Denon AVR-591 Home Theater System User Manual

Model 435
Owner’s Guide
G435A
Downloaded from: http://www.guardianalarms.net
Limited Lifetime
Consumer Warranty
Directed Electronics, Inc. ("DEI®") promises to the original purchaser to repair or replace with a comparable reconditioned model any DEI unit (hereafter the "unit"), excluding
without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable
use during the lifetime of the vehicle provided the following conditions are met: the
unit was professionally installed and serviced by an authorized DEI dealer; the unit will
be professionally reinstalled in the vehicle in which it was originally installed by an
authorized DEI dealer; and the unit is returned to DEI, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following
information: consumer's name, telephone number and address; the authorized dealers
name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle
identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry
a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty
card and mailed it within ten (10) days of the date of purchase to the address listed
on the card; the unit's date code or serial number is defaced, missing or altered; the
unit has been modified or used in a manner contrary to its intended purpose; the unit
has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The
warranty does not cover damage to the unit caused by installation or removal of the
unit. DEI, in its sole discretion, will determine what constitutes excessive damage and
may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT
ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY, ARE EXPRESSLY EXCLUDED; AND DEI NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY
IN CONNECTION WITH ITS PRODUCTS. DEI DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED
DEALERS OR INSTALLERS. DEI SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DEI IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS
OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM.
THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR
© 1999 Directed Electronics, Inc.
i
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN
THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DEI OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA
STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DEI SHALL BE STRICTLY
LIMITED TO THE AUTHORIZED DEI DEALER'S PURCHASE PRICE OF THE UNIT. DEI SHALL
NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE
LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER
A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED
ABOVE. Some states do not allow limitations on how long an implied warranty will last
or the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights and you may also have other rights that vary from State
to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized DEI dealer for details of the plan or call DEI Customer Service at 1-800-876-0800.
DEI security systems, including this unit, are deterrents against possible theft. DEI is
not offering a guarantee or insurance against vandalism, damage or theft of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including
without limitation, liability for theft, damage and/or vandalism. DEI does not and has
not authorized any person or entity to create for it any other obligation, promise, duty
or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
■
■
■
■
■
■
■
■
■
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 1999 Directed Electronics, Inc.
Table of Contents
Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Transmitter Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Disarming Without a Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Silent Mode™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Valet® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Nuisance Prevention® Circuitry (NPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Arming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disarming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Code Hopping™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Owner Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Multi-vehicle Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rapid Resume Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Security & Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Glossary Of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Quick Reference Guide (Removable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
© 1999 Directed Electronics, Inc.
1
Standard Configuration
2
© 1999 Directed Electronics, Inc.
What is Included
■ A control module
■ Two four-button remote transmitters
■ A Stinger® dual-stage shock sensor (on-board the control module)
■ A Revenger® Soft Chirp® six-tone programmable siren
■ A red status LED indicator light
■ A push-button Valet switch
■ A Failsafe® Starter Kill relay (may require additional labor)
Important Information
This security system has been designed to provide years of troublefree operation. Due to its complexity, it must be installed by an
authorized dealer only. Installation of this product by anyone other
than an authorized dealer voids the warranty. All dealers are provided with preprinted dealer certificates to verify that they are
authorized.
By carefully reading this owner's guide prior to using your security system, you will maximize the use of this system and its
features.
© 1999 Directed Electronics, Inc.
3
System Maintenance
This system requires no specific maintenance. Your remote is powered by a miniature 3-volt battery, type 2032, that lasts approximately
one year under normal use. When the battery weakens, the LED on
the remote will dim and operating range will be reduced.
Your Warranty
Your warranty card must be returned and the barcode serial number
must not be removed. If the warranty card is not returned, no warranty will be honored on your unit. It is also necessary to keep your
proof of purchase, which reflects that the product was installed by
an authorized dealer. Make sure you receive the warranty card from
your dealer.
FCC/ID Notice
This device complies with part 15 of FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this device.
4
© 1999 Directed Electronics, Inc.
Transmitter Functions
Your vehicle security system is programmable, making it possible
to assign any button on the remote to any specific receiver function. The transmitter initially comes programmed with the Standard
Configuration, but may also be customized by an authorized dealer.
Unless otherwise specified, all instructions in this manual assume
operation using the Standard Configuration.
Standard Configuration
The functions of the buttons described below correspond to a transmitter programmed with the default Standard Configuration. These
buttons will function differently in a Custom Configuration.
Button
The arming and locking functions are controlled by pressing this button for one second.
Button
The disarming and unlocking functions are controlled by pressing
this button for one second.
Button
Silent Mode™ and an optional auxiliary function are controlled by pressing this button. Silent Mode™ works by pressing
for less than
one second. An optional auxiliary function, such as trunk release,
is controlled by pressing and holding
for 1.5 seconds. The aux-
iliary output controls _____________________________.
© 1999 Directed Electronics, Inc.
5
Button
Panic Mode is activated by pressing and holding
for one sec-
ond.
and
Buttons
An optional auxiliary convenience or expansion function that you
have added to your system can be activated by pressing these buttons simultaneously.
The auxiliary output controls _____________________________.
and
Buttons
Another optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls _____________________________.
6
© 1999 Directed Electronics, Inc.
Using Your System
The buttons described in all instructions in this manual correspond
to the standard configuration, unless otherwise specified.
Arming
You can arm the security system and lock your vehicle’s doors (if
connected) by pressing
for one second. When the system arms,
you will hear a short siren sound (chirp) and the parking lights will
flash once. Once armed, the status LED will flash twice per second
to indicate that the system is actively protecting your vehicle. If
you hear a second chirp after arming and notice that the status LED
is flashing in a grouped pattern, this signals Bypass Notification,
which is described in the Diagnostics section of this manual.
The system can also be programmed to arm itself automatically 30
seconds after the ignition is turned off and the last vehicle door has
been closed (called Passive Arming). Once the 30-second countdown
period initiates, the status LED will flash twice as fast as it does
when the system is armed. After 20 seconds, the siren will chirp once
to warn that the system has only 10 seconds remaining prior to arming. The system is not actually armed at this point. The system arms
itself at the 30-second mark. At this point, the vehicle doors will
also lock (if programmed for Passive Locking) and the status LED
will begin flashing twice per second to indicate armed status. If Passive Locking is activated, care must be taken to prevent the keys
from being locked in the vehicle.
© 1999 Directed Electronics, Inc.
7
NOTE: If any protected entry point (such as a door or switch-protected trunk
or hood) is open, Passive Arming will not engage. Additionally, each time
a sensor is triggered during the 30-second arming countdown, the countdown starts over.
Arming your security system protects your vehicle in the following
ways:
■ Light impacts will trigger a Warn Away® Response, causing the
siren to chirp and the parking lights to flash for a few seconds.
■ Heavy impacts will trip a Triggered Sequence, causing the siren to
sound continuously and the parking lights to flash for 30 seconds.
■ If a door is opened, the siren immediately starts chirping and
the parking lights start flashing to provide an instant response.
Three seconds later, the siren output changes to a continuous
blast. This two-stage Progressive Response allows you time to
disarm the system with your transmitter if the door is inadvertently opened while the system is armed.
■ Turning on the ignition key triggers the same two-stage Progressive
Response as opening a door.
■ The Failsafe® Starter Kill Relay prevents the vehicle’s starter from
cranking.
Disarming
Press
to disarm the security system and unlock the doors (if
connected). Disarming is confirmed when the parking lights flash
twice and the siren emits two chirps. The siren chirping either four
or five times when disarming indicates Tamper Alert, which is described in the Diagnostics section of this manual.
8
© 1999 Directed Electronics, Inc.
Disarming Without a Transmitter
This feature allows you to disarm the security system without the
remote transmitter, in case that the transmitter is lost, damaged or
disabled. To disarm the system without a transmitter, you must have
the vehicle’s ignition key and know where the Valet switch is located.
Be sure to check with your installer at the time of installation for
both the location and the preset response (1-5 presses) of the
Valet switch.
To disarm the system, turn the ignition
key on and press the Valet switch the
preset number of times within 15 seconds. If the security system does not
DRW-35
disarm, you may have waited too long;
turn the ignition off and repeat the
process.
IMPORTANT: The Valet switch can be programmed to respond to 1-5
presses for the disarm function. You must check with the installer to verify the programming for your individual unit.
LOCATION OF VALET SWITCH_____________________________
Silent Mode
Use Silent Mode to temporarily turn off the arming or disarming chirps
by briefly pressing
before either arming or disarming. The con-
firmation chirp(s) will be eliminated for that one operation only.
To permanently turn off the arming and disarming chirps, contact
your dealer.
© 1999 Directed Electronics, Inc.
9
NOTE: The Warn Away® Response to lighter impacts is bypassed if the system is armed using the Silent Mode. This ensures that the siren does not
chirp in an environment where you don’t want chirps to be emitted. The
system is still capable of being triggered by heavier impacts; only the Warn
Away Response generated by light impacts is bypassed.
Panic Mode
If you are threatened in or near your vehicle, pressing
on your
remote transmitter for 1.5 seconds will trigger your alarm system
and attract attention. The siren will sound and the parking lights
will flash for 30 seconds. To stop the Panic Mode at any time, press
,
, or
.
Valet® Mode
Valet Mode prevents your system from arming and triggering either automatically or with the transmitter. In Valet Mode, all
convenience functions (door locks, trunk release, etc.) will remain
operational. This feature is useful when washing or servicing
your vehicle.
To enter or exit Valet Mode with the Valet switch:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet switch
DRW-35
within 10 seconds.
The status LED will light steadily if you are entering Valet Mode
and will turn off if you are exiting Valet Mode.
10
© 1999 Directed Electronics, Inc.
Remote Valet®
You can also enter or exit Valet Mode using your remote transmitter:
1. Open any vehicle door.
2. Press
.
3. Press
.
4. Press
again.
The status LED will light solid if you are entering Valet Mode and
will turn off if you are exiting Valet Mode.
Nuisance Prevention® Circuitry
Your system has Nuisance Prevention® Circuitry (NPC®) to prevent
annoying repetitive trigger sequences caused by faulty door pin
switches or environmental conditions such as thunder, jackhammers,
airport noise, etc.
Here’s how NPC® works: If the alarm is triggered by the same sensor or switch three times within a 60-minute period, your system
interprets this pattern of triggers as false alarms. After the third
trigger, your system ignores, or bypasses, that sensor or switch (along
with any other sensors or switches sharing the same zone) for 60
minutes. If the bypassed sensor is triggered again while it is already
being bypassed, the 60-minute bypass period will start over.
This ensures that a sensor that is continually being triggered will
remain bypassed.
NOTE: Arming and disarming the system does not reset the Nuisance Prevention Circuitry. The only ways to reset a bypassed zone are for that zone
not to be triggered for 60 minutes or to turn the ignition key on. When
© 1999 Directed Electronics, Inc.
11
testing your system, it is important to remember that this circuitry can
cause zones to be bypassed and appear to not work. If five chirps are heard
when disarming the system, the NPC was engaged. To clear the memory,
turn the ignition key on.
Diagnostics
The microprocessor at the heart of your system has the ability to
constantly monitor all of the switches and sensors connected to it.
It can detect any faulty switches or sensors and prevent them from
disabling the entire system. It can also record and report any triggers that occur when you are away from your vehicle.
Arming Diagnostics
If the security system is armed at the same time that an input is
active (door opening, sensor triggering, etc.), you will hear one chirp
to indicate arming and a second chirp to indicate Bypass Notification. A Bypass Notification chirp means that the system ignores the
input that was active when the system was armed, until that input
ceases. Three seconds after that input ceases, the system will resume normal monitoring. For example, if your vehicle has an interior
light exit delay and you arm the system before the light turns off,
you may hear a second Bypass Notification chirp. Once the light turns
off, however, the system resumes normal monitoring.
NOTE: Bypass Notification does not occur when the system is in Silent Mode
or if the chirps have been programmed by the installer not to sound.
12
© 1999 Directed Electronics, Inc.
Disarming Diagnostics
Your system has a Tamper Alert feature that notifies you of triggers
that occur while you are away from your vehicle. If you hear four chirps
when you disarm, this indicates that the system was triggered in your
absence. If you hear five chirps when you disarm, this indicates that
a specific zone was triggered so many times that the Nuisance Prevention Circuitry has bypassed that zone. In both cases, the pattern
of the flashing status LED will indicate which zone was triggered (see
Table of Zones). The system retains this information in its memory
and will continue to chirp four or five times each time the system
is disarmed, until the next time the ignition is turned on.
Table of Zones
A zone is represented by the number of LED flashes used by the system to identify a particular type of input. Standard input assignments
are listed below, along with spaces to write in any optional sensors
or switches that have been installed.
ZONE
(Number of
LED Flashes)
DESCRIPTION
1
Instant trigger—often used
for hood/trunk pinswitches
2
Instant trigger—a heavier impact
detected by the shock sensor
3
Door switch trigger
4
Instant trigger—for optional
sensors
5
Ignition trigger
© 1999 Directed Electronics, Inc.
DEALER-INSTALLED
OPTIONS
13
Code Hopping ®
The receiver and transmitter use mathematical formulas called algorithms to change their codes each time the transmitter is used. This
Code Hopping technology has been developed to increase the security of the unit. By following this set code sequence, the receiver and
transmitter stay synchronized, even if the remote transmitter is used
out of range of the vehicle. If, however, the transmitter is pressed many
times out of range of the vehicle, or the battery is removed, the transmitter may get temporarily out of sync and fail to operate the system.
To resynchronize the remote transmitter, simply press
several
times within range of the vehicle. The system will automatically resynchronize and the transmitter will respond normally.
Owner Recognition
Using a system programming device, your dealer can program specific
settings for each transmitter that is used with your system. The system is then capable of recalling the individual settings assigned to
each transmitter. This Owner Recognition feature allows up to four
users of the same system to have four different settings that meet
their individual needs.
NOTE: Owner Recognition cannot be programmed without a system programming device and the necessary software. Check with your dealer for
more information.
14
© 1999 Directed Electronics, Inc.
Multi-Vehicle
Operation
Your DEI security system has the ability to interface with other DEI
vehicle security systems to control multiple vehicles using the same
remote transmitter. Contact your local DEI dealer for more details.
Rapid Resume Logic
Your security system stores its current operational state in non-volatile
memory, so that if power is lost and then reconnected, the system
will recall the stored state from memory. For example, if the system
is in Valet Mode when the battery is disconnected, it will still be in
Valet Mode when the battery is reconnected. This applies to all system features, including arming, disarming, and Valet Mode.
Installation Options
Your system has some options that may require extra parts and labor.
One of these options, Progressive Unlocking, configures the system
so that when you press
locks. Pressing
to disarm, only the driver’s door un-
again within 15 seconds unlocks the remaining
doors.
© 1999 Directed Electronics, Inc.
15
Programming Options
Programming options control your system’s normal, operational setup. Most options do not require additional parts, but some may require
installation labor.
The system’s programming options are listed below. The factory default settings are in bold:
■ Active Arming (only with the transmitter) or Passive Arming (automatic arming 30 seconds after the last door is closed).
■ Arming and disarming confirmation siren chirps, on or off.
■ Ignition controlled door lock feature, on or off. With this feature on, the doors will lock three seconds after the ignition key
is turned on, and unlock when the ignition is turned off. The
system also prevents the doors from locking when the ignition
is turned on while any vehicle door is open.
■ Active Door Locking (only when arming with the transmitter)
or Passive Door Locking (with Passive Arming).
■ Valet Switch Pulse Count: The number of times the Valet switch
needs to be pressed to disarm the system. One to five pulses
can be programmed, with the default setting being one pulse.
■ Siren Tones and Chirp Volume: The output of the soft chirp siren
consists of six different tones in sequence. Your dealer can
eliminate any of these tones, resulting in a unique, easily identifiable siren sound. The chirps can be programmed for either
full volume or six decibels quieter than the full alarm blast.
16
© 1999 Directed Electronics, Inc.
Security & Convenience
Expansions
Many options can be added to your system for increased security,
protection and convenience. A few of these options are listed below.
Contact your dealer for a complete list of options compatible with
your system.
Digital Failsafe® Starter Kill: The 103T Digital Failsafe Starter Kill
can be used as serial controller to enhance your vehicle’s security system. With the 103T, you can control your system’s basic functions from
an illuminated, dash-mounted keypad. Simply enter coded key sequences to control arming, disarming, panic and Valet Mode functions.
Dome Light Supervision: If this option is installed, the dome light
will illuminate for 30 seconds each time the system is disarmed using
the transmitter. This is useful in dark environments for seeing inside the vehicle prior to entering it.
Valet® Start System: For the ultimate convenience option, the Valet
Start System can start your vehicle, monitor engine functions, and
power your climate control system with a push of a button. Overrev protection, open-hood lockout, brake pedal shutoff, and automatic
timer shutoff are also included. This option is available only for automatic transmission, fuel-injected gasoline vehicles.
Power Window Control: You can add various power window control
features with either the 529T Power Window Roll-Up Module or the
530T Window Automation System.
© 1999 Directed Electronics, Inc.
17
Glossary of Terms
Control Module: The “brain” of your system. Usually hidden underneath
the dash area of the vehicle. It houses the microprocessor that monitors your vehicle and controls all of the alarm’s functions.
Failsafe® Starter Kill Relay: An automatic switch controlled by the
security system that prevents the vehicle’s starter from cranking whenever the system is armed. The vehicle is never prevented from
cranking when the system is disarmed, in Valet Mode, or if the Starter
Kill Relay fails.
Input: Any physical connection to the security system. An input can
be provided through a sensor, pinswitch or by existing systems in
the vehicle, such as ignition or courtesy lights.
LED: A red light mounted inside the vehicle, at a location determined
by the installer. The LED indicates the status of your system and also
reports triggers and faults in the system or sensors.
Siren: A noise generating device, usually installed in the engine compartment of the vehicle. The siren generates the chirps and tones
heard when the system is triggered.
Stinger® Double-Guard® Shock Sensor: A dual-stage shock sensor,
which is located on the control module, and is designed to detect
impacts to the vehicle or glass.
18
© 1999 Directed Electronics, Inc.
Transmitter: A hand-held, remote control that operates the various functions of the security system.
Trigger or Triggered Sequence: The “setting off” or “tripping” of
the alarm. A Triggered Response consists of the siren sounding and
the parking lights flashing for 30 seconds.
Valet Switch: A small, push-button switch mounted inside the vehicle, at a location determined by the installer. This switch is used
to override the alarm when a transmitter is lost or damage, or can
be used to put the system into Valet Mode.
Warn Away Response: Light impacts to the vehicle generate the Warn
Away Response, which consists of several seconds of siren chirps and
flashing parking lights.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular zone.
Two or more inputs may share the same zone.
© 1999 Directed Electronics, Inc.
19
Notes
20
© 1999 Directed Electronics, Inc.
✂
Quick Reference Operating Card
To arm the system using your transmitter
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
■ Press
for one second to arm the system and lock the doors (if the
door locks are connected to the system). When the system arms, you will
hear one chirp and the parking lights will flash once.
To disarm the system using your transmitter
■ Press
to disarm the system and unlock the doors (if the door locks
are connected to the system). When the system disarms, you will hear
two chirps and the parking lights will flash twice.
Disarming without a transmitter
■ To disarm without a transmitter, you must have the vehicle’s ignition key
and know where the Valet switch is. (Contact your installer for both the
location and the preset number of presses required for the Valet switch).
Turn on the ignition key. Press the Valet switch the pre-programmed number of times within 15 seconds. If the system does not disarm, you may
have waited too long; turn the ignition off and repeat the process.
To enter or exit Valet Mode
■ To enter or exit Valet Mode, turn the ignition key on and then off. Then
press and release the Valet switch within 10 seconds. The status LED will
light steadily if you are entering Valet Mode and will turn off if you are
exiting Valet Mode.
To activate Panic Mode
■ Press and hold
for 1.5 seconds.
To exit Panic Mode
■ Press
,
, or
.
To activate Silent® Mode
✂
■ Press
briefly before arming or disarming. The confirmation chirp(s)
will be eliminated for that one operation only.
© 1999 Directed Electronics, Inc.
21
The company behind this system is Directed Electronics, Inc.
Since its inception, DEI® has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of more
than 20 patents in the field of advanced electronic technology, DEI is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 477-1372 for more information about our products and services.
DEI is committed to delivering on time, the best products we know how to provide, and
to constantly work with our customers and vendors to improve our products, quality,
delivery and customer friendly features.
®
Directed Electronics, Inc.
Vista, CA 92083
www.dei.com
© 1999 Directed Electronics, Inc. - All rights reserved
G435A 2/00
Download PDF

advertising