Operating instructions | Denon AVR-886 Stereo Receiver User Manual

AV SURROUND RECEIVER
AVR-886
OPERATING INSTRUCTIONS
MODE D’EMPLOI
FRANCAIS
SAFETY INSTRUCTIONS
2 SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
FCC INFORMATION (For US customers)
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this product may not cause
harmful interference, and (2) this product must accept any interference
received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modification not expressly
approved by DENON may void your authority, granted by the FCC, to
use the product.
3. NOTE
This product has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This product generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product
OFF and ON, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of
product or an experienced radio/TV technician for help.
ENGLISH
1.
Read Instructions – All the safety and operating instructions should be
read before the product is operated.
2. Retain Instructions – The safety and operating instructions should be
retained for future reference.
3. Heed Warnings – All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should be
followed.
5. Cleaning – Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in
a wet basement; or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
9. A product and cart combination should be moved
with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11. Power Sources – This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer
or local power company. For products intended to operate from
battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization – This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
13. Power-Cord Protection – Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
product.
15. Outdoor Antenna Grounding – If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See Figure A.
16. Lightning – For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to
lightning and power-line surges.
17. Power Lines – An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them
might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
19. Object and Liquid Entry – Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
20. Servicing – Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21. Damage Requiring Service – Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance – this
indicates a need for service.
22. Replacement Parts – When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23. Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
ENGLISH
FRANCAIS
2 System setup menu / Menu de configuration système
page
page
page
page
page
8~11
50
50, 51
51
51
page
page
page
page
page
46
47
47, 48
48
49
page
page
page
page
page
page
page
41
41
41
42
42
43
43
page 44
page 44
page
page
page
page
45
45
45
46
ENGLISH
Getting Started
Advanced Operation
Getting Started
Thank you for choosing the DENON AVR-886 A/V Surround Receiver. This remarkable component has been engineered to provide
superb surround sound listening with home theater sources, such as DVD, as well as providing outstanding high fidelity reproduction
of your favorite music sources.
As this product is provided we recommend with an immense array of features, before you begin hookup and operation that you review
the contents of this manual before proceeding.
Contents
Getting Started
Accessories ··············································································2
Before using·············································································2
Cautions on installation ·························································2
Cautions on handling······························································2
Preparing the remote control unit ········································2
Inserting the batteries ····························································3
Operating range of the remote control unit ························3
Part names and functions
Front panel··············································································3
Remote control unit································································4
Easy Setup and Operation
Easy setup flow ·······································································4
Speaker system layout ···························································5
Speaker connections ··························································5, 6
Connecting a DVD player and monitor TV···························7
Auto Setup / Room EQ
Connecting a microphone ······················································8
Turning on the power ·····························································8
Starting Auto Setup ································································9
About error messages ··························································10
Check of the measurement results································10, 11
Playing a DVD with surround sound ··································11
Connecting Other Sources
Cable indications···································································11
The video conversion function ············································12
On screen display signals·····················································12
Connecting a TV/DBS tuner ················································13
Connecting a video camera or video game························13
Connecting the external inputs (EXT. IN) terminals··········13
Connecting a CD player························································13
Connecting a DVD recorder ·················································14
Connecting a VCR ·································································14
Connecting a tape deck························································15
Connecting a turntable·························································15
Connecting a CD recorder or MD recorder·························15
Connecting the antenna terminals······································16
Connecting the XM terminal ···············································16
Connecting the MULTI ZONE terminals
ZONE2 out connections ·······················································17
ZONE2 speaker out connections··········································17
Connecting the pre-out terminals ·······································18
Connecting the power supply cord·····································18
Basic Operation
Playback
Playing the input source ·······················································19
Playback using the external input (EXT. IN) terminals ··········19
Turning the sound off temporarily (MUTING) ·······················19
Listening over headphones ··················································20
Combining the currently playing sound with the
desired image (VIDEO SELECT) ···········································20
Selecting the front speakers ················································20
Checking the currently playing program source···················20
Input mode ·····································································20, 21
Surround
Playing audio sources (CDs and DVDs)
2-channel playback modes ···················································21
Dolby Pro Logic IIx (Pro Logic II) mode ·······························22
DTS NEO:6 mode ·································································23
Dolby Digital mode and DTS surround ···························24, 25
Night mode···········································································25
Adjusting the audio delay ·····················································26
DENON original surround modes
Surround modes and their features······································26
DSP surround simulation ······················································27
Room EQ setting ··································································28
Tone control setting
• Adjusting the sound quality ·············································29
• Tone defeat mode ···························································29
Channel Level ·······································································29
Listening to the radio
Auto preset memory ····························································30
Auto tuning ···········································································30
Manual tuning·······································································31
Preset stations······································································31
Checking the preset stations················································31
Recalling preset stations ······················································31
XM Satellite Radio ································································32
Checking the XM signal strength and Radio ID ···················32
Channel selection ·································································32
Category search····································································32
Remote control unit
Operating DENON audio components ·································33
Preset memory·····································································34
Operating a component stored in the
preset memory·······························································34~36
Punch through ······································································36
Multi zone music entertainment system ···························37
Outputting a program source to amplifier, etc.,
in a different room (ZONE2 mode)·······································38
Remote control unit operations during
multi-source playback ···························································38
Other functions
Playing one source while recording another
(REC OUT mode) ··································································39
Last function memory ··························································39
Initialization of the microprocessor·······································39
Advanced Setup – Part 1
Navigating through the System Setup Menu····················40
On screen display and front display ···································40
Input Setup
Setting the Digital In Assign. ················································41
Setting the Ext In SW Level ·················································41
Setting the Input Function Level ··········································41
Setting the Function Rename···············································42
Setting the Component In Assign. ·······································42
Setting the Video Input Mode ··············································43
Setting the Auto Tuner Preset··············································43
Advanced Playback
Setting the Audio Delay························································44
Setting the Auto Surround Mode ·········································44
Option Setup
Setting the Muting Level······················································45
Setting the On Screen Display ·············································45
Setting the Power Amp Assign. ···········································45
Setting the Setup Lock·························································46
Advanced Setup – Part 2
Speaker Setup
Setting the Speaker Config. ·················································46
Setting the Delay Time ·························································47
Setting the Channel Level ··············································47, 48
Setting the Crossover Frequency·········································48
Setting the SW Mode Setup ················································49
Others Setup
Setting the Manual EQ Setup···············································50
Setting the Room EQ Setup···········································50, 51
Setting the Direct Mode Setup ············································51
Check the EQ parameter······················································51
System setup items and default values ·······················52, 53
Troubleshooting ····································································54
Additional information···················································55~60
Specifications ········································································61
List of preset codes ····································End of this manual
1
ENGLISH
ENGLISH
Getting Started
Getting Started
Accessories
Cautions on installation
Check that the following parts are included in addition to the main unit:
q Operating instructions ............................1
w Warranty .................................................1
e Service station list ..................................1
r Remote control unit (RC-1004) ...............1
r
t
Noise or disturbance of the picture may be
generated if this unit or any other electronic
equipment using microprocessors is used near
a tuner or TV.
If this happens, take the following steps:
• Install this unit as far away as possible
from the tuner or TV.
• Run the antenna wires from the tuner or
TV away from this unit’s power supply cord
and input/output connection cables.
• Noise or disturbance tends to occur
particularly when using indoor antennas or
300 Ω/ohm feeder wires. We recommend
using outdoor antennas and 75 Ω/ohm
coaxial cables.
t R6P/AA batteries ....................................2
y AM loop antenna ....................................1
u FM indoor antenna .................................1
i Omnidirectional microphone...................1
y
u
i
Before using
Pay attention to the following before using this
unit:
• Moving the unit
To prevent short-circuits or damaged wires in
the connection cables, always unplug the power
supply cord and disconnect the connection
cables between all other audio components
when moving the unit.
• Before turning the power switch on
Check once again that all connections are
correct and that there are not problems with
the connection cables. Always set the power
switch to the standby position before
connecting and disconnecting connection
cables.
Note
Wall
Note:
For heat dispersal, do not install this unit in a confined space such as a bookcase or similar
enclosure.
• Store these instructions in a safe place.
After reading, store this instructions along with
the warranty card in a safe place.
• Note that the illustrations in these
instructions may differ from the actual unit
for explanation purposes.
Cautions on handling
• Switching the input source when input terminals are not connected.
A clicking noise may be produced if the input source is switched when nothing is connected to
the input terminals. If this happens, either turn down the MASTER VOLUME control knob or
connect components to the input terminals.
• V. AUX terminals
The AVR-886’s front panel is equipped with V.
AUX terminals. Remove the cap covering the
terminals when you want to use them.
• Muting of PRE OUT terminals, PHONES jack and SPEAKER terminals.
The PRE OUT terminals, PHONES jack and SPEAKER terminals include a muting circuit. Because
of this, the output signals are greatly attenuated for several seconds after the power switch is
turned on or the input source, surround mode or any other set-up is changed. If the volume is
turned up during this time, the output will be very high after the muting circuit stops functioning.
Always wait until the muting circuit turns off before adjusting the volume.
• Whenever the power switch is in the STANDBY state, the unit is still connected to AC line
voltage.
Please be sure to turn off the power switch or unplug the cord when you leave home for,
say, a vacation.
Preparing the remote control unit
The included remote control unit (RC-1004) can be used to operate not only the AVR-886 but other
remote control compatible DENON components as well. In addition, the memory contains control
signals for other remote control units, so it can be used to operate non-DENON remote control
compatible products.
2
ENGLISH
ENGLISH
Getting Started
Getting Started
Inserting the batteries
Part names and functions
q Remove the remote control unit’s rear
cover.
w Set two R6P/AA batteries in the battery
compartment in the indicated direction.
e Put the rear cover back on.
Notes on batteries:
• Replace the batteries with new ones if the set
does not operate even when the remote
control unit is operated nearby the unit. (The
included batteries are only for verifying
operation.)
• When inserting the batteries, be sure to do so
in the proper direction, following the “<” and
“>” marks in the battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an
old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• If the battery fluid should leak, carefully wipe
the fluid off the inside of the battery
compartment and insert new batteries.
• When replacing the batteries, have the new
batteries ready and insert them as quickly as
possible.
Front panel
For details on the functions of these parts, refer to the pages given in parentheses ( ).
#5 #4
t u
o !1
i !0
q we r y
q Power ON/STANDBY switch ················(8)
w Power indicator······································(8)
e Power switch ···································(8, 39)
r Headphones jack (PHONES) ···············(20)
t ANALOG button···································(20)
y SPEAKER A/B buttons ··················(20, 39)
u ZONE2 button ······································(38)
i Preset station select buttons ·······(30, 31)
o STANDARD/NIGHT button ···········(22~25)
!0 5CH/7CH STEREO button ···················(26)
!1 STEREO/DIRECT/PURE DIRECT
Operating range of the remote control unit
• Point the remote control unit at the remote sensor on the main unit as shown in the diagram.
• The remote control unit can be used from a straight distance of approximately 23 feet from the
main unit, but this distance will be shorter if there are obstacles in the way or if the remote control
unit is not pointed directly at the remote sensor.
• The remote control unit can be operated at a horizontal angle of up to 30 degrees with respect
to the remote sensor.
30°
30°
Approx. 23 feet
@7
@2 @0
#3 #2 #1 #0 @9 @8 @6 @5 @4 @3 @1
NOTE:
• It may be difficult to operate the remote control
unit if the remote sensor is exposed to direct
sunlight or strong artificial light.
• Do not press buttons on the main unit and
remote control unit simultaneously. Doing so
may result in malfunction.
• Neon signs or other devices emitting pulsetype noise nearby may result in malfunction,
so keep the set as far away from such devices
as possible.
button ···················································(21)
!2 V. AUX INPUT terminals ·····················(13)
!3 SETUP MIC jack ·····································(8)
!4 SURROUND MODE button ·················(19)
!5 SURROUND PARAMETER
button ···················································(22)
!6 SELECT knob····························(19, 22, 29)
!7 TONE DEFEAT button··························(29)
3
ENGLISH
!2
!9
!4
!3 !5 !6 !7 !8
!8 TONE CONTROL button······················(29)
!9 MASTER VOLUME control knob ········(19)
@0 TUNING • (up)/ª (down) buttons ·····(30)
@1 STATUS button ······························(20, 25)
@2 DIMMER button ···································(20)
@3 VIDEO SELECT button·························(20)
@4 OUTPUT indicator··························(24, 38)
@5 Master volume indicator·····················(19)
@6 Display
@7 INPUT mode indicator·························(21)
@8 SIGNAL indicator ·································(21)
@9 BAND button ········································(30)
#0 EXT. IN button······································(19)
#1 Remote control sensor··························(3)
#2 INPUT MODE button ···························(20)
#3 ZONE2/REC SELECT button ·········(38, 39)
#4 FUNCTION knob ····························(19, 38)
#5 MAIN button·········································(19)
ENGLISH
Getting Started
Remote control unit
Easy Setup and Operation
For details on the functions of these parts, refer to the pages given in parentheses ( ).
Indicator ···············(34, 36)
ZONE2 buttons····(36, 38)
SURROUND MODE
buttons·················(19, 27)
Power buttons
································(8, 34)
• This section contains the basic steps necessary to configure the AVR-886 according to your
listening room environment and the source equipment and loudspeakers you are using.
• For optimum performance, we recommend using the Auto Setup function.
• If you wish, you can set the various settings manually without using Auto Setup (
page 46 ~
51).
MAIN buttons
································(4, 36)
Easy setup flow
Remote control signal
transmitter···················(3)
Placing the speakers.
Auto setup flow
Input source selector
buttons·················(19, 34)
Connecting a microphone.
Connecting the
speakers.
Tuner system/System
buttons·················(30, 35)
Connecting a monitor
and a DVD player.
Mode selector switches
································(8, 33)
System buttons
······························(33~35)
Master volume control
buttons·················(19, 38)
SYSTEM SETUP/SETUP
button·····················(9, 34)
MUTING button
····································(19)
Cursor buttons
································(9, 22)
SURROUND
PARAMETER/System
button···················(22, 34)
ON SCREEN/DISPLAY
button ············(20, 25, 34)
TEST TONE button
····································(48)
VIDEO SELECT button
····································(20)
Input mode selector
buttons·················(19, 20)
Starting the Auto
Setup.
1)
2)
3)
4)
Speaker Configuration
Delay Time
Channel Level
Room EQ
Check of the measurement result.
Store the measurement result in the memory.
Playing a DVD with
surround sound.
CH SELECT/ENTER
button·················(9, 23, 29)
SURROUND BACK/
RETURN button···(24, 34)
SPEAKER button
································(8, 20)
DIMMER button
····································(20)
MEMO
• The Dolby Surround Pro Logic II(x) Cinema or Music mode can be chosen directly by pressing the
CINEMA or MUSIC button on the remote control unit during playback in the Dolby Surround Pro
Logic II(x) mode.
• The DTS NEO:6 Cinema or Music mode can be chosen directly by pressing the CINEMA or MUSIC
button on the remote control unit during playback in the DTS NEO:6 mode.
• The main zone output can be turned on and off with the MAIN button.
Measurement of the speakers
in the listening position.
4
ENGLISH
ENGLISH
Easy Setup and Operation
Easy Setup and Operation
Speaker system layout
Speaker connections
• Connect the speaker terminals with the
speakers making sure that like polarities are
matched (< with <, > with >). Mismatching
of polarities will result in weak central sound,
unclear orientation of the various instruments,
and the stereo image being impaired.
• When making connections, take care that
none of the individual conductors of the speaker
cable come in contact with adjacent terminals,
with other speaker cable conductors, or with
the rear panel.
2 Basic system layout
The following is an example of the basic layout for a system consisting of eight speaker systems
and a television monitor:
Subwoofer
Center speaker system
Surround back speaker systems
NOTE:
NEVER touch the speaker terminals
when the power is on. Doing so could
result in electric shocks.
Connecting the speaker cables
1. Loosen by turning
counterclockwise.
2. Insert the cable.
3. Tighten by turning
clockwise.
Connecting banana plugs
Banana plug
2 Speaker impedance
Front speaker systems
Set these at the sides of the TV
or screen with their front surfaces
as flush with the front of the
screen as possible.
• When speaker systems A and B are used
separately, speakers with an impedance of 6
to 16 Ω/ohms can be connected for use as
front speakers.
• Be careful when using two pairs of front
speakers (A + B) at the same time, since
speakers with an impedance of 12 to 16
Ω/ohms in this case must be used.
• Speakers with an impedance of 6 to 16
Ω/ohms can be connected for use as center
and surround and surround back speakers.
• The protector circuit may be activated if the
unit is operated for long periods of time at
high volumes when speakers with an
impedance lower than the specified
impedance are connected.
Surround speaker systems
Note on speaker impedance
The protector circuit may be activated if the
unit is operated for long periods of time at
high volumes when speakers with an
impedance lower than the specified
impedance (for example speakers with an
impedance of less than 4 Ω/ohms) are
connected. If the protector circuit is
activated, the speaker output is cut off. Turn
off the unit’s power, wait for the unit to cool
down, improve the ventilation around the
unit, then turn the power back on.
5
ENGLISH
Turn clockwise to
tighten, then insert
the banana plug.
Protector circuit
This unit is equipped with a high-speed
protection circuit. The purpose of this circuit
is to protect the speakers under circumstances
such as when the output of the power
amplifier is inadvertently short-circuited and
a large current flows, when the temperature
surrounding the unit becomes unusually
high, or when the unit is used at high output
over a long period which results in an
extreme temperature rise.
When the protection circuit is activated, the
speaker output is cut off and the power
supply indicator flashes. Should this occur,
please follow these steps: be sure to switch
off the power of this unit, check whether
there are any faults with the wiring of the
speaker cables or input cables, and wait for
the unit to cool down if it is very hot.
Improve the ventilation condition around the
unit and switch the power back on.
If the protection circuit is activated again
even though there are no problems with the
wiring or the ventilation around the unit,
switch off the power and contact a DENON
service center.
ENGLISH
Easy Setup and Operation
Easy Setup and Operation
2 Connections
2 Bi-Amp connections
When making connections, also refer to the operating instructions of the other components.
Certain loudspeakers are equipped with two sets of input terminals, for bi-amplification. The AVR886 Power Amp Assign. mode allows you to power bi-amp-capable speakers with two amplifier
channels (
page 45). Be sure to consult the owner’s manual of your bi-amp-capable speakers
for further information before proceeding.
Center
speaker
Subwoofer
Surround speaker
systems
AVR-886
(L)
IN
>
>
<
(R)
< >
<
Connection terminal
for a subwoofer with
built-in amplifier.
SPEAKER
SPEAKER
NOTE:
• When making Bi-Amp connections, be sure to remove the short-circuiting bar included with
the speaker.
(L)
<
(R)
>
>
Front speaker
systems (B)
(L)
<
<
(L)
(R)
>
>
<
Front speaker
systems (A)
Precautions when connecting speakers:
If a speaker is placed near a TV or video
monitor, the colors on the screen may be
disturbed by the speaker’s magnetism. If
this should happen, move the speaker away
to a position where it does not cause this
effect.
>
(R)
< >
<
Surround back
speaker systems
NOTE:
• When using only one surround back speaker,
connect it to the left channel.
6
ENGLISH
ENGLISH
Easy Setup and Operation
Easy Setup and Operation
• For best picture quality (especially with progressive DVD and other high definition sources),
choose the component video connection to your monitor TV. S-Video and composite video
outputs are also provided if your TV does not have component video inputs.
Connecting a DVD player and monitor TV
• To connect the video output from the DVD player to the AVR-886, you only need to choose one
connection type. Component video connection offers the best quality (and is required for
progressive DVD playback), followed by S-Video, while composite video offers the lowest picture
quality of the three connection types. For more information about the video up conversion
function (
page 12).
• To connect the digital audio output from the DVD player, you can choose from either the coaxial
or optical connections. If you choose to use the coaxial connection, it needs to be assigned. For
more information about Digital Input Assignment (
page 41).
• Connect a non-DVD video disc player (such as a laser disc, VCD/SVCD, or future high definition
disc player) to the DVD/VDP terminals in the same way.
Monitor TV
I
Y
PB
PR
H
S VIDEO
IN
G
DVD player
I
COMPONENT VIDEO IN
VIDEO
IN
COMPONENT VIDEO OUT
Y
PB
PR
H
NOTE:
• The component video input and/or output terminals may be labeled differently on some TVs,
monitors or video components (Y, PB, PR; Y, CB, CR; Y, B-Y, R-Y). Check the owner’s manuals
for the other components for further information.
S VIDEO
OUT
G
VIDEO
OUT
D
OPTICAL
OUT
A
AUDIO OUT
L
L
L
R
R
R
Audio signal flow is shown with white arrows; video signal flow is shown with gray arrows.
7
ENGLISH
ENGLISH
Easy Setup and Operation
Easy Setup and Operation
ON/SOURCE
POWER
SPEAKER A
MODE 1
ENTER
SETUP
CURSOR
ON/STANDBY
SETUP MIC
Auto Setup / Room EQ
Connecting a microphone
1
Connect the microphone for Auto Setup to the
SETUP MIC jack on the front panel of the unit.
q: This sets the speaker connection, polarity, and bass
reproduction ability.
w: This sets the delay time from each speaker corresponding to
the listening position.
e: This sets the volume that is output from each speaker.
r: This sets the frequency response of each speaker.
Press the POWER switch.
The power turns on and the indicator lights.
Set the POWER switch to this position to turn the power on
and off from the included remote control unit.
The power turns off and the indicator is off.
In this position, the power cannot be turned on and off from
the remote control unit.
4
Press the ON/STANDBY switch on the main unit
or ON/SOURCE button on the remote control
unit.
• Turn on the power.
2
Place the microphone for Auto Setup at the
actual listening position which will be at the
same height as your ears.
Microphone
NOTE:
• A loud test tone is output during the measurement. Please
consider this should you be planning night time
measurements, and consider not allowing small children
into the listening room at this time.
Turn on your monitor (TV).
£ OFF:
2 Measurement and setting details
For accurate measurements
• Keep quiet during the auto setup procedure. It is recommended
that you turn off the power of any air-conditioner, projector or
other equipment that may produce noise.
• Do not stand between the microphone and speakers while
Auto Setup is performed.
• Do not place any obstacles between the microphone and
speakers. Also, be sure to point the speakers towards the
listening position.
1
2
3
Turn on your subwoofer.
¢ ON:
SPEAKER
The Auto Setup and Room EQ function of this unit performs an
analysis of the speaker system and measures the acoustic
characteristics of your room to permit an appropriate automatic
setting.
Turning on the power
Place the microphone on a tripod or level surface.
8
ENGLISH
5
6
Press the SPEAKER A button to turn the speakers
on.
Set the MODE 1 switch to “AUDIO” (only when
operating with the remote control unit).
ENGLISH
Easy Setup and Operation
Starting Auto Setup
1
Press the SETUP button.
• The “System Setup” menu appears.
Easy Setup and Operation
When “S. Back” is selected, the test tone during Auto
Setup will be output from the surround back speaker.
When “ZONE2” is selected, change the setting to
“ZONE2”. The test tone during Auto Setup is set so that it
will not be output to ZONE2 (Another room).
When “Bi-Amp” is selected, change the setting to “BiAmp”. The test tone during Auto Setup is set so that it will
be output from the Bi-Amp speaker.
5
2
• Measurement is cancelled if the MASTER VOLUME control knob
is operated while the Auto Setup is performed.
• If the output volume and crossover frequency of your
subwoofer speaker can be changed, then set the volume to
halfway and the crossover filter to maximum or switch off
the low-pass filter.
2 About automatic retry
Press the CURSOR D or H button to select
“Start”, then press the CURSOR F button.
• Start the measurements.
Press the CURSOR D or H button to select “Auto
Setup/Room EQ”, then press the ENTER button.
To confirm the results of the measurements, remeasurement is
automatically performed.
Remeasurement is performed up to 2 times. During this time,
“Retry1” or “Retry2” is displayed on the screen.
• The “Auto Setup/Room EQ” menu appears.
Measurement of each channel is performed as follows:
1
FL
3
Press the CURSOR D or H button to select “Auto
Setup”, then press the ENTER button.
4
Press the CURSOR D or H button to select
“Power Amp Assign”, then press the CURSOR F
or G button to select “S. Back”, “ZONE2” or
“Bi-Amp”.
• The “Auto Setup” screen appears.
2
FR
C
SW
3
SL
SR
SBL
SBR
1: Only the front speakers (A) are measured, front speakers
(B) are not available. Even if the front speakers (B) are
set, the setting automatically switches to the front
speakers (A) once measurements are completed.
2: The subwoofer speaker is measured twice.
3: When “ZONE2” and “Bi-Amp” are selected, these are
not displayed.
After each channel is measured, “Calculating” appears.
The display switches to the Auto Setup check screen
automatically.
9
ENGLISH
NOTE:
• When measurements have been made using the
measurement microphone, speakers with built-in filters,
such as a subwoofer, might be set to a value that differs
from the physical distance because of the internal electrical
delay.
ENGLISH
Easy Setup and Operation
Easy Setup and Operation
Check of the measurement results
About error messages
• These error screens may be displayed when performing Auto Setup measurement and the automatic measurements can not be
completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters,
reset the pertinent items, and measure again.
• When there is too much noise in the room, the speakers may not be detected properly. Should this happen, perform the
measurements when the noise level is low, or switch off the power of the equipment that is producing the noise for the duration
of the measurements.
Screen example
Cause
1
Press the CURSOR D or H button to select an
item, then press the ENTER button.
Measures
q This screen will be displayed when the speakers • Check that the pertinent speakers are
required for producing suitable reproduction have properly connected.
not been detected.
• The front L or front R speaker was not properly
detected.
• Only one channel of the surround speakers was
detected.
• Sound was output from the R channel when only
one surround back speaker was connected.
• The surround back speaker was detected, but the
surround speaker was not detected.
The measurement results of each item can be checked
here.
2
Press the ENTER button.
• The verification screen appears.
Example: Speaker Config. Check
w This screen will be displayed when the speaker • Check the polarity of the pertinent
speakers. For some speakers, this
polarity is connected in reverse.
screen may be displayed even though
the speakers are properly connected. If
so, select “Skip0”.
e This screen will be displayed when accurate • Set up the speakers so that their position
measurements cannot be made due to the input is farther away from the listening
position.
level of the microphone being too high.
• Lower the volume of the subwoofer
speaker.
r This screen will be displayed when
measurement microphone is not connected.
the • Connect the measurement microphone
to the microphone connector.
10
ENGLISH
3
Press the ENTER button again once you have
checked the results.
ENGLISH
Easy Setup and Operation
4
Press the CURSOR D or H button to select from
the following three items based on the
measurement results, then press the CURSOR F
button.
Connecting Other Sources
Cable indications
The hookup diagrams on the subsequent pages assume the use of the following optional connection cables (not supplied).
Store:
Store the checked measurement values.
All parameters are stored.
Retry:
Perform the measurement again.
Measurement is repeated.
Audio cable
A
Cancel:
Cancel the checked measurement values.
Video cable
G
Analog terminal (Stereo)
(White)
L
L
(Red)
R
R
Video terminal
(Yellow)
Video cable (75 Ω/ohm video pin-plug cable)
Pin-plug cable
B
Analog terminal (Monaural, for subwoofer)
H
S-Video terminal
Pin-plug cable
C
I
Digital terminal (Coaxial)
Coaxial cable (75 Ω/ohm pin-plug cable)
1
2
3
4
5
D
Component video terminal
(Y)
(Green)
(Orange)
Playing a DVD with surround sound
S-Video cable
(PB/CB)
(Blue)
(Red)
Digital terminal (Optical)
(PR/CR)
Component video cable
Signal direction
Disconnect the microphone from the unit.
Optical cable (Optical fiber cable)
Select the input source to be played.
E
Speaker terminal
Audio signal
Select the play (surround) mode.
Speaker cable
Start DVD playback.
Adjust the volume.
F
XM terminal
IN
OUT
OUT
IN
IN
OUT
OUT
IN
Video signal
XM cable
NOTE:
• Do not plug in the power supply cord until all connections have been completed.
• When making connections, also refer to the operating instructions of the other components.
• Be sure to connect the left and right channels properly (left with left, right with right).
• Note that binding pin-plug cables together with power supply cords or placing them near a power transformer will result in hum
or other noise.
11
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
The video conversion function
On screen display signals
With the AVR-886, the Video signal and the S-Video signal which
were inputted are mutually converted. And also the Video signal
and the S-Video signal which were inputted are converted into a
higher quality.
The flow of the video signals.
(Component video
terminals)
(Component video
terminals)
VIDEO signal
input terminal
(yellow)
S-Video signal
input terminal
Video signal output to
VIDEO MONITOR OUT
terminal (yellow)
Video signal output to
S-Video MONITOR OUT
terminal
Video signal output to Color
Difference (Component) Video
MONITOR OUT terminal
1
E
E
C
C
C
2
C
E
C
C
C
3
E
C
C
C
C
E
C
4
C
(C: Signal
(S-Video terminal)
(S-Video terminal)
(Video terminal)
(Video terminal)
This unit’s input
terminals
This unit’s output
terminals
On screen display signal output
Signals input to the AVR-886
C
E: No signal)
Cautions on the video conversion function:
When the component video terminals are used to connect the
AVR-886 with a TV (or monitor, projector, etc.) and the video
(yellow) or S-Video terminals are used to connect the AVR-886
with a VTR, depending on the combination of the TV and VTR
the picture may flicker in the horizontal direction, be distorted,
be out of sync not display at all when playing video tapes.
If this happens, connect a commercially available video
stabilizer, etc., with a TBC (time base corrector) function
between the AVR-886 and the VTR, or if your VTR has a TBC
function, turn it on.
12
ENGLISH
(C: On screen signals output
C
E: On screen signals not output)
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting a TV/DBS tuner
Connecting the external inputs (EXT. IN) terminals
• For best picture quality choose the component video connection to your TV or DBS tuner. S-Video
and composite video inputs are also provided if your TV or DBS tuner does not have component
video outputs.
• To connect the digital audio output from the TV or DBS tuner, you can choose from either the
coaxial or optical connections. If you choose to use the coaxial connection, it needs to be
assigned. For more information about Digital Input Assignment (
page 41).
• These terminals are for inputting multi-channel audio signals from an external decoder, or a
component with a different type of multi-channel decoder, such as a DVD Audio player, a multichannel Super Audio CD player, or another future multi-channel sound format decoder.
• The video signal connection is the same as that for a DVD player.
• For instructions on playback using the external input (EXT. IN) terminals (
page 19).
DVD Audio-Video /
Super Audio CD player /
External decoder
TV
I
COMPONENT VIDEO OUT
A
Y
L
PB
R
5.1ch AUDIO OUT
FRONT
L
L
R
R
PR
B
H
CENTER
S VIDEO
OUT
A
G
VIDEO
OUT
D
L
L
SURROUND
L
R
R
R
B
SUBWOOFER
OPTICAL
OUT
A
AUDIO OUT
L
L
L
R
R
R
• With discs on which special copyright protection measures have been taken, the digital signals
may not be output from the DVD player. In this case, connect the DVD player’s analog multichannel output to the AVR-886’s EXT. IN terminals for playback. Also refer to your DVD player’s
operating instructions.
Connecting a video camera or video game
G
Video camera /
Video game
Connecting a CD player
VIDEO
OUT
A
To connect the digital audio output from the CD player, you can choose either coaxial or optical
connection. If you choose to use the optical connection, it needs to be assigned. For more
information about Digital Input Assignment (
page 41).
AUDIO OUT
L
L
L
R
R
R
CD player
D
OPTICAL
OUT
AUDIO OUT
A
H
L
L
L
R
R
R
S VIDEO
OUT
C
COAXIAL
OUT
13
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting a DVD recorder
Connecting a VCR
• For best picture quality choose the component video connection to your VCR. S-Video and
composite video outputs are also provided. If you choose to use the component video
connection, it needs to be assigned. For more information about Component Input Assignment
(
page 42).
• You can connect a second video recorder to the VCR-2 terminals.
• If you wish to perform analog dubbing from a digital source, such as a DVD recorder to an analog
recorder such as a cassette deck, you will need to connect the analog inputs and outputs as
shown below, in addition to the digital audio connections.
• The digital inputs and outputs connection is the same as that for a CD (MD) recorder.
DVD recorder
H
G
S VIDEO
OUT
VIDEO
OUT
G
H
VIDEO
OUT
I
Video deck
S VIDEO
OUT
COMPONENT VIDEO OUT
G
Y
VIDEO
IN
PB
H
PR
S VIDEO
IN
G
VIDEO
IN
A
H
S VIDEO
IN
AUDIO IN
L
L
L
R
R
R
A
D
OPTICAL
IN
AUDIO OUT
L
L
L
R
R
R
D
OPTICAL
OUT
NOTE:
• When recording to VCR, it is necessary that the type of cable used with the playback source
equipment be the same type that is connected to the AVR-886 VCR-1 (to 2) OUTPUT terminal.
Example: VCR-2 IN → S-Video cable : VCR-2 OUT → S-Video cable
VCR-2 IN → Video cable : VCR-2 OUT → Video cable
C
COAXIAL
OUT
A
AUDIO IN
L
L
L
R
R
R
A
AUDIO OUT
L
L
R
R
L
R
NOTE:
• When recording to a DVD recorder, it is necessary that the type of cable used with the
playback source equipment be the same type that is connected to the AVR-886 VCR-1 (to 2)
OUTPUT terminal.
Example: VCR-1 IN → S-Video cable : VCR-1 OUT → S-Video cable
VCR-1 IN → Video cable : VCR-1 OUT → Video cable
14
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting a tape deck
Connecting a CD recorder or MD recorder
If you wish to perform analog dubbing from a digital source, such as a CD or MD recorder to an
analog recorder such as a tape deck, you will need to connect the analog inputs and outputs as
shown below, in addition to the digital audio connections.
Tape deck
AUDIO OUT
A
L
L
L
R
R
R
A
L
L
R
R
CD recorder /
MD recorder
AUDIO OUT
AUDIO IN
A
L
L
L
L
R
R
R
R
D
OPTICAL
OUT
D
OPTICAL
IN
• If humming noise is generated, move the tape deck further away from the source of such noise.
AUDIO IN
A
Connecting a turntable
If humming or other noise is generated when the ground wire is connected, disconnect the ground
wire.
L
L
R
R
R
NOTE:
• Do not connect the output of the component connected to the OPTICAL 3 OUT terminal on
the AVR-886’s rear panel to any terminal other than the OPTICAL 3 IN terminal (
page 41).
Turntable
(MM cartridge)
A
L
L
AUDIO OUT
R
GND
NOTE:
• The phono input can accept signals from moving magnet (MM) and high output moving coil
(MC) phono cartridges. If your turntable is equipped with a low output MC cartridge, you will
need to use a separate MC head amplifier or step-up MC transformer.
15
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting the antenna terminals
Connecting the XM terminal
• AVR-886 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the
XM Connect-and-Play™ (sold separately) and subscribing the XM service.
• Plug the XM Connect-and-Play antenna into XM terminal on the rear panel.
• Position the XM Connect-and-Play antenna near a south-facing window to receive the best signal.
For details, see “XM Satellite Radio” (
page 32).
When making connections, also refer to the operating instructions of the XM Connect-and-Play
antenna.
An FM antenna cable plug can be connected directly to the unit.
Direction of broadcasting
station
AM loop
antenna
(Supplied)
FM antenna
75 Ω/ohm
COAXIAL
cable
FM indoor
antenna
(Supplied)
Note to CATV system installer:
This reminder is provided to call the
CATV system installer’s attention to
Article 820-40 of the NEC which
provides guidelines for proper
grounding and, in particular, specifies
that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as practical.
XM Connect-and
-Play Antenna
XM
F
NOTE:
• Do not connect two FM antennas
simultaneously.
• Even if an external AM antenna is
used, do not disconnect the AM
loop antenna.
• Make sure the AM loop antenna
lead terminals do not touch metal
parts of the panel.
Ground
NOTE:
• Keep the power supply cord unplugged until the XM Connect-and-Play antenna connection
have been completed.
AM outdoor antenna
2 AM loop antenna assembly
1
2
Connect to the AM
antenna terminals.
Connection of AM antennas
3
1. Push the lever.
Remove the vinyl tie
and take out the
connection line.
Bend in the reverse
direction.
4
a. Antenna placed on
a stable surface.
2. Insert the conductor.
Mount
b. Hanging the
antenna on a wall.
3. Return the lever.
Use the
installation hole to secure the antenna to a wall, etc.
16
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting the MULTI ZONE terminals
ZONE2 speaker out connections
For instructions on operations using the MULTI ZONE functions (
• When the power amplifier is assigned to the ZONE2 output channel at “Power Amp Assign.” in
the “System Setup” menu, the surround back speaker terminals can be used as the ZONE2
speaker out terminals (
page 37).
• The connections diagram below is an example for when the surround back speaker is assigned
to the ZONE2 stereo 2 channel.
In this case, surround back speaker out can not be used for MAIN ZONE.
page 37, 38).
ZONE2 out connections
• If another power amplifier or pre-main (integrated) amplifier is connected, the ZONE2 out (variable
level) terminals can be used to play a different program source in ZONE2 the same time (
page 37).
• When a sold separately room-to-room remote control unit (DENON RC-616, 617 or 618) is wired
and connected between the MAIN ZONE and ZONE2, the remote-controllable devices in the
MAIN ZONE can be controlled from ZONE2 using the remote control unit.
Center
speaker
Subwoofer
Surround speaker
systems
(L)
Power amplifier
(ZONE2)
A
L
IN
L
L
IN
R
R
R
(Variable)
>
>
<
(R)
< >
<
Connection terminal
for a subwoofer with
built-in amplifier.
RC-617 INFRARED SENSOR
+
OUTPUT
+
INPUT
AUX OUT
Extension terminals for future use.
RC-616 INFRARED
RETRANSMITTER
NOTE:
• For instructions on installation and operation of separately sold devices, refer to the devices’
operating instructions.
(L)
<
(R)
>
>
Front speaker
systems (B)
(L)
<
<
(L)
(R)
>
>
Front speaker
systems (A)
<
>
(R)
< >
<
ZONE2 speaker
systems
NOTE:
• The settings must be
changed to use this
speaker for ZONE2 (
page 45).
17
ENGLISH
ENGLISH
Connecting Other Sources
Connecting Other Sources
Connecting the pre-out terminals
• Use these terminals if you wish to connect external power amplifier(s) to increase the power of
the front, center, surround and surround back sound channels, or for connection to powered
loudspeakers.
• When using only one surround back speaker, connect it to the left channel.
Power amplifier
B
CENTER
A
L
L
SURROUND
L
R
R
R
A
L
L
R
R
SURROUND
BACK
L
R
B
SUBWOOFER
A
L
L
FRONT
L
R
R
R
Connecting the power supply cord
AC outlets (Wall)
AC 120 V, 60 Hz
AC OUTLETS
• SWITCHED (total capacity – 120 W (1 A.))
The power to these outlets is turned on and
off in conjunction with the POWER switch on
the main unit, and when the power is
switched between on and standby from the
remote control unit.
No power is supplied from these outlets
when this unit’s power is at standby. Never
connect equipment whose total power
consumption exceeds 120 W (1 A.).
NOTE:
• Only use the AC OUTLETS for connecting audio equipment. Never use it for hair driers, TVs
or other electrical appliances.
18
ENGLISH
ENGLISH
Basic Operation
Playback using the external input (EXT. IN)
terminals
Basic Operation
The signals being input to the external decoder input terminals
are played without passing through the surround circuitry.
Playback
MASTER VOLUME
INPUT MODE ANALOG
FUNCTION
DIMMER STATUS
SURROUND
MODE
FUNCTION
VIDEO SELECT
MAIN
EXT. IN
SELECT
SURROUND MODE
PHONES SPEAKER
VOLUME
MUTING
Playing the input source
1
Example: CD
(Main unit)
(Remote control unit)
To select the input source when ZONE2/REC OUT is selected,
press the MAIN button, then operate the input function
selector.
2
ON SCREEN
VIDEO SELECT
INPUT MODE
Select the input source to be played.
Select the play (surround) mode.
3
Start playback on the selected component.
For operating instructions, refer to the component’s manual.
4
SELECT
(Main unit)
(Remote control unit)
To select the surround mode while adjusting the surround
parameters, tone defeat or tone control, press the SURROUND
MODE button and then operate the selector.
• Canceling the external input mode:
Press the INPUT MODE or ANALOG button to switch to the
desired input mode (
page 20, 21).
• The external input mode can be set for any input source. To
watch video while listening to sound, select the input source to
which the video signal is connected, then set this mode.
• If the subwoofer output level is too high, set the “SW ATT.”
surround parameter to “ON”.
NOTE:
• When the input mode is set to the external input (EXT. IN),
the play mode (DIRECT PURE DIRECT, VIRTUAL SURROUND,
STEREO, STANDARD (DOLBY/DTS SURROUND), 5CH/7CH
STEREO or DSP SIMULATION) cannot be selected.
• In play modes other than the external input mode, the
signals connected to the EXT. IN terminals cannot be
reproduced. In addition, signals cannot be output from
channels not connected to the input terminals.
Turning the sound off temporarily (MUTING)
Use this to turn off the audio output temporarily.
Press the MUTING button.
Adjust the volume.
Example: STEREO
(Main unit)
DIMMER
SPEAKER
EXT. IN
ANALOG
Press the EXT. IN button to select the external input.
• You can adjust the muting level (
The volume level is
displayed on the
master volume level
(Remote control unit) display.
The volume can be adjusted within the range of –80 to 0 to
18 dB, in steps of 0.5 dB. However, when the channel level
is set as described (
page 29), if the volume for any
channel is set at +0.5 dB or greater, the volume cannot be
adjusted up to 18 dB. (In this case the maximum volume is
adjusted to “18 dB — (Maximum value of channel level)”.)
19
ENGLISH
page 45).
• Canceling the MUTING mode:
q Press the MUTING button again.
w Press the VOLUME button on the remote control unit, or
adjust the volume up or down via the front panel MASTER
VOLUME knob.
ENGLISH
Basic Operation
Basic Operation
Listening over headphones
Connect the headphones to the PHONES jack.
• The pre-out output (including the speaker output) is automatically
turned off when headphones are connected.
Checking the currently playing program
source
2 On screen display
Press the ON SCREEN button.
NOTE:
• To prevent hearing loss, do not raise the volume level
excessively when using headphones.
Combining the currently playing sound with
the desired image (VIDEO SELECT)
Press the VIDEO SELECT button repeatedly until the
desired source appears on the display.
IN=V SOURCE
Use this switch to monitor a video source other than the
audio source.
Each time an operation is performed, a description of that
operation appears on the display connected to the unit’s
VIDEO MONITOR OUT terminal. Also, the unit’s operating
status can be checked during playback.
Such information as the position of the input selector and
the surround parameter settings is output in sequence.
2 Front panel display
Press the STATUS button.
Descriptions of the unit’s operations are also displayed on
the front panel display. In addition, the display can be
switched to check the unit’s operating status while playing
a source.
2 Using the dimmer function
• Canceling simulcast playback:
q Select “SOURCE” by pressing the VIDEO SELECT button.
w Switch the program source to the component connected to
the video input terminals.
The front speaker A, B setting can be also be changed with
the SPEAKER button on the remote control unit.
PCM (exclusive PCM signal playback mode):
Decoding and playback are only performed when PCM signals
are being input.
Note that noise may be generated when using this mode to
play signals other than PCM signals.
DTS (exclusive DTS signal playback mode):
Decoding and playback are only performed when DTS signals
are being input.
2 Selecting the analog mode
Press the DIMMER button.
The display brightness changes in four steps (bright, medium,
dim and off).
Press the ANALOG button to switch to the analog
input.
ANALOG (exclusive analog audio signal playback mode):
The signals input to the analog input terminals are decoded
and played.
Selecting the front speakers
Press the SPEAKER A or B button to turn the
corresponding speaker pair on.
AUTO (auto mode):
In this mode, the types of signals being input to the digital and
analog input terminals for the selected input source are
detected and the program in the AVR-886’s surround decoder
is selected automatically upon playback. This mode can be
selected for all input sources other than PHONO and TUNER.
The presence or absence of digital signals is detected, the
signals input to the digital input terminals are identified and
decoding and playback are performed automatically with the
DTS, Dolby Digital or PCM (2 channel stereo) format. If no
digital signal is being input, the analog input terminals are
selected.
Use this mode to play Dolby Digital signals.
Input mode
The AVR-886 has an AUTO signal detection mode that
automatically identifies the type of incoming audio signals, but is
also equipped with a manual mode that can be switched
according to the type of input audio signals.
2 Selecting the AUTO, PCM and DTS modes
Press the INPUT MODE button.
The mode switches as shown below each time the INPUT
MODE button is pressed:
AUTO
PCM
20
ENGLISH
DTS
NOTE:
• Input mode when playing DTS sources:
Noise will be output if DTS-compatible CDs or LDs are
played in the “ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect
the source component to the digital input terminals
(OPTICAL/COAXIAL) and set the input mode to “DTS”.
ENGLISH
Basic Operation
Basic Operation
2 Input mode display
• In the AUTO mode
STEREO/DIRECT/PURE DIRECT
Depending on the input signal.
STANDARD
DIRECT/
PURE DIRECT
STEREO
• In the DIGITAL PCM mode
ENTER
• In the DIGITAL DTS mode
STANDARD
SELECT
SURROUND PARAMETER
CURSOR
SURROUND
PARAMETER
• In the ANALOG mode
Surround
2 Input signal display
• The AVR-886 is equipped with 2-channel playback modes
exclusively for music.
• Select the mode to suit your tastes.
• DOLBY DIGITAL
• DTS
• PCM
Playing audio sources (CDs and DVDs)
2-channel playback modes
The “DIGITAL” indicator lights
when digital signals are being input
properly. If the “DIGITAL” indicator
does not light, check whether the
Digital In Assign. setup (
page
41) and connections are correct and
whether the component’s power is
turned on.
2 PURE DIRECT mode
Use this mode to achieve good quality 2-channel sound while
watching images. In this mode, the audio signals bypass such
circuits as the tone circuit and display circuit and are transmitted
directly, resulting in good quality sound.
Press the STEREO/DIRECT/PURE DIRECT button on
the main unit or the DIRECT/PURE DIRECT button
on the remote control unit to select the PURE DIRECT
mode.
NOTE:
• The “DIGITAL” indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will
be heard.
21
ENGLISH
2 DIRECT mode
Use this mode to achieve good quality 2-channel sound while
watching images. In this mode, the audio signals bypass such
circuits as the tone circuit and are transmitted directly, resulting
in good quality sound.
Press the STEREO/DIRECT/PURE DIRECT button on
the main unit or the DIRECT/PURE DIRECT button
on the remote control unit to select the DIRECT
mode.
2 STEREO mode
Use this mode to adjust the tone and achieve the desired sound
while watching images.
Press the STEREO/DIRECT/PURE DIRECT button on
the main unit or the STEREO button on the remote
control unit to select the STEREO mode.
ENGLISH
Basic Operation
Basic Operation
Dolby Pro Logic IIx (Pro Logic II) mode
• To play in the PLIIx mode, set “S. BackSp” at the “Speaker
Configuration” setting to “1sp” or “2sp”.
• To play in the PLIIx mode, set “Surround Back” at the “Power
Amp Assign.” setting.
1
When the “SB CH OUT” parameter is set to “OFF”. (Set
“S. BACK” at system setup to “NONE”.)
Display
(Pro Logic II Cinema mode)
Press the STANDARD button to select the Dolby
Pro Logic IIx mode.
(Pro Logic II Music mode)
• The Dolby Pro Logic II indicator lights.
(Pro Logic II Game mode)
Lights
(Dolby Pro Logic mode)
The mode switches as shown below each time the
STANDARD button is pressed.
DOLBY PLIIx
2
DTS NEO:6
Play a program source.
5
Press the SURROUND PARAMETER button, and
press the CURSOR D or H button to select the
various parameters.
Example: DOLBY PLIIx music mode screen
For operating instructions, refer to the manuals of the
respective components.
3
Press the SURROUND PARAMETER button to
select the surround parameter mode.
See “Surround parameters q” for a description of the various
parameters.
6
4
Turn the SELECT knob, and press the CURSOR
F or G button to select the optimum mode for
the source.
When the “SB CH OUT” parameter is set to “ON”. (Set “S.
BACK” at system setup to “SMALL” or “LARGE”.)
Display
(Pro Logic IIx Cinema mode)
Turn the SELECT knob, and press the CURSOR
F or G button to set the various surround
parameters.
When the surround parameters are set using the buttons on
the main unit, stop operating the buttons after completing
the settings. The settings are automatically finalized and the
normal display reappears after several seconds.
7
Press the ENTER button to finish the surround
parameter mode.
(Pro Logic IIx Music mode)
(Pro Logic IIx Game mode)
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
22
ENGLISH
2 Surround parameters q
Pro Logic IIx and Pro Logic II Mode:
The Cinema mode is for use with stereo television shows and
all programs encoded in Dolby Surround.
The Music mode is recommended for stereo music and
surround-encoded stereo music sources.
The Pro Logic mode offers the same robust surround
processing as original Pro Logic in case the source content is
not of optimum quality.
The Game mode is for playing games. The game mode can only
be used with 2-channel audio sources.
Select one of the modes (“Cinema”, “Music”, “Pro Logic” or
“Game”).
• Panorama Control:
This mode extends the front stereo image to include the
surround speakers for an exciting “wraparound” effect with
side wall imaging.
Select “OFF” or “ON”.
• Dimension Control:
This control gradually adjusts the soundfield either towards
the front or towards the rear.
The control can be set in 7 steps from 0 to 6.
• Center Width Control:
This control adjusts the center image so it may be heard only
from the center speaker; only from the left/right speakers as
a phantom image; or from all three front speakers to varying
degrees.
The control can be set in 8 steps from 0 to 7.
ENGLISH
Basic Operation
Basic Operation
2 Surround parameters w
STANDARD
FUNCTION INPUT MODE SURROUND MODE
FUNCTION
ENTER
SURROUND
PARAMETER
CURSOR
STANDARD
SELECT
SURROUND PARAMETER
SURROUND
BACK
INPUT MODE
DTS NEO:6 mode
1
Press the STANDARD button to select the DTS
NEO:6 mode.
The mode switches as shown below each time the button
is pressed.
DOLBY PLIIx
2
3
4
5
DTS NEO:6
Play a program source.
Press the SURROUND PARAMETER button to
select the surround parameter mode.
Turn the SELECT knob, and press the CURSOR
F or G button to select the optimum mode for
the source.
6
Turn the SELECT knob, and press the CURSOR
F or G button to set the various surround
parameters.
When the surround parameters are set using the buttons on
the main unit, stop operating the buttons after completing
the settings. The settings are automatically finalized and the
normal display reappears after several seconds.
7
Press the ENTER button to finish the surround
parameter mode.
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
Press the SURROUND PARAMETER button, and
press the CURSOR D or H button to select the
various parameters.
23
ENGLISH
DTS NEO:6 Mode:
• Cinema:
This mode is optimum for playing movies. Decoding is
performed with emphasis on separation performance to
achieve the same atmosphere with 2-channel sources as with
6.1-channel sources.
This mode is effective for playing sources recorded in
conventional surround formats as well, because the in-phase
component is assigned mainly to the center channel (C) and the
reversed phase component to the surround (SL, SR and SB
channels).
• Music:
This mode is suited mainly for playing music. The front channel
(FL and FR) signals bypass the decoder and are played directly
so there is no loss of sound quality, and the effect of the
surround signals output from the center (C) and surround (SL,
SR and SB) channels add a natural sense of expansion to the
sound field.
CENTER IMAGE (0.0 to 1.0: default 0.3):
The center image parameter for adjusting the expansion of the
center channel in the DTS NEO:6 MUSIC mode has been
added.
ENGLISH
Basic Operation
Basic Operation
Dolby Digital mode and DTS surround
(only with digital input)
1
Select an input source set to digital (COAXIAL/
OPTICAL) (
page 41).
Example: DVD
(Main unit)
2
3
7
8
Turn the SELECT knob, and press the CURSOR
F or G button to adjust the parameter settings.
Press the ENTER button to finish the surround
parameter mode.
Press the INPUT MODE button to set the input
mode to “AUTO” or “DTS”.
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
Press the STANDARD button to select the
STANDARD (Dolby/DTS Surround) mode.
2 Surround parameters e
Play a program source with the
symbol.
• The Dolby Digital indicator lights
when playing Dolby Digital
sources.
• The DTS indicator lights when
playing DTS sources.
Operate the SURROUND BACK button
to switch Surround Back CH ON/OFF.
• The SURROUND BACK indicator
lights when the SURROUND BACK
button is on.
5
Press the SURROUND PARAMETER button, and
press the CURSOR D or H button to select the
various parameters.
(Remote control unit)
When performing this operation from the main unit’s panel,
press the SURROUND MODE button, then turn the SELECT
knob and select Dolby Pro Logic IIx or DTS NEO:6.
4
6
or
Lights
Lights
Lights
Press the SURROUND PARAMETER button.
• The surround parameter screen is displayed.
Program source and adjustment range:
1. Dolby Digital: –10 dB to 0 dB
2. DTS Surround: –10 dB to 0 dB
When DTS encoded movie software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
correct DTS playback.
When DTS encoded music software is played, it is
recommended that the LFE LEVEL be set to –10 dB for
correct DTS playback.
TONE:
This enables the tone control. This can be set individually for
the separate surround modes other than PURE DIRECT and
DIRECT mode.
SB CH OUT (Surround Back):
D.COMP. (Dynamic Range Compression):
Motion picture soundtracks have tremendous dynamic range
(the contrast between very soft and very loud sounds). For
listening late at night, or whenever the maximum sound level is
lower than usual, the Dynamic Range Compression allows you
to hear all of the sounds in the soundtrack (but with reduced
dynamic range). (This only works when playing program
sources recorded in Dolby Digital or DTS). Select one of the
four parameters (“OFF”, “LOW”, “MID” (middle) or “HIGH”).
Set to OFF for normal listening.
(1) Multi-channel source
• OFF:
Playback is conducted without using the surround back
speaker.
• NON MTRX:
The same signals as those of the surround channels are
output from the surround back channels.
• MTRX ON:
The surround back channel is reproduced using digital matrix
processing.
• ES MTRX:
When playing DTS signals, the surround back signals undergo
digital matrix processing for playback.
• ES DSCRT:
When a signal identifying the source as a discrete 6.1-channel
source is included in the DTS signals, the surround back
signals included in the source are played.
• PLIIx Cinema:
Processing is performed with the Cinema mode of the PLIIx
decoder and the surround back channel is reproduced.
• PLIIx Music:
Processing is performed with the Music mode of the PLIIx
decoder and the surround back channel is reproduced.
LFE (Low Frequency Effect):
This sets the level of the LFE (Low Frequency Effect) sounds
included in the source when playing program sources recorded
in Dolby Digital or DTS.
If the sound produced from the subwoofer sounds distorted
due to the LFE signals when playing Dolby Digital or DTS
sources when the peak limiter is turned off with the subwoofer
peak limit level setting (system setup menu), adjust the level as
necessary.
(2) 2ch source
• OFF:
Playback is conducted without using the surround back
speaker.
• ON:
Playback is conducted using the surround back speaker.
This operation can be performed directly by pressing the
SURROUND BACK button.
CINEMA EQ. (Cinema Equalizer):
The Cinema EQ function gently decreases the level of the
extreme high frequencies, compensating for overly-bright
sounding motion picture soundtracks. Select this function if the
sound from the front speakers is too bright.
This function only works in the Dolby Pro Logic IIx, Dolby
Digital, DTS Surround and DTS NEO:6 modes. (The same
contents are set for all operating modes.)
24
ENGLISH
ENGLISH
Basic Operation
Basic Operation
2 Dialog normalization
FUNCTION INPUT MODE
STATUS
The dialog normalization function is activated automatically when
playing Dolby Digital program sources.
Dialog normalization is a basic function of Dolby Digital which
automatically normalizes the dialog level (standard level) of the
signals which are recorded at different levels for different
program sources, such as DVD, DTV and other future formats
that will use Dolby Digital.
These contents can be verified with the STATUS or ON SCREEN
buttons.
STANDARD
FUNCTION
Display
ENTER
STANDARD/NIGHT
OFFSET
CURSOR
ON SCREEN
- 4dB
The number indicates the normalization level when the
currently playing program is normalized to the standard level.
INPUT MODE
2 Checking the input signal
The input signal can be checked by pressing the remote control
unit’s ON SCREEN button.
SIGNAL:
Displays the type of signal (DTS, DOLBY DIGITAL, PCM, etc.).
• In addition, screen information is displayed in the following
order when the ON SCREEN button is pressed repeatedly:
OSD-1
Input signal
OSD-2
Input/output
OSD-3
Auto surround mode
OSD-4~10 Tuner preset stations
fs:
Displays the input signal’s sampling frequency.
FORMAT:
Displays the input signal’s number of channels.
“Number of front channels/Number of surround channels/ LFE
on/off”.
“SURROUND” is displayed for 2-channel signal sources
recorded in Dolby Surround.
OFFSET:
Displays the dialog normalization offset value.
FLAG:
Displays the special identification signal recorded in the input
signal.
“MATRIX” is displayed when matrix processing is conducted
on the surround back channel, “DISCRETE” is displayed when
discrete processing is conducted.
Not displayed if an identification signal has not been recorded.
Night mode
When listening at night or at lower volumes, the night mode
improves listenability.
Press and hold the NIGHT button for several seconds
to enter the night mode.
• Canceling night mode:
Press and hold the NIGHT button again.
• The night mode only works when playing program sources
recorded in Dolby Digital or DTS.
NOTE:
• OSD-3:
This is displayed when the auto surround mode is set to
“ON” and the input mode is set to “Auto”.
It is not displayed when the input mode is set to “Analog”
or “EXT. IN”.
25
ENGLISH
ENGLISH
Basic Operation
Basic Operation
Adjusting the audio delay
• When watching a DVD or other video source, the picture on the
monitor may seem delayed with respect to the sound. In this
case, adjust the audio delay to delay the sound and synchronize
it with the picture.
• The audio delay setting is stored separately for each input
source.
• This adjustment can be performed with the system setup
(
page 44) or from the remote control unit, as described
below.
1
• The audio delay setting does not apply when playing in the EXT. IN mode or in the analog input direct, pure direct or stereo mode
(TONE DEFEAT “ON”).
DENON original surround modes
This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically
recreate the sound field. One of 7 preset surround modes can be selected according to the program source and the parameters can
be adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound.
Surround modes and their features
Select the input source.
Example: DVD
1 5CH/7CH STEREO
2
(Main unit)
2
3
(Remote control unit)
Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming from all
directions.
Press the INPUT MODE button to set the input
mode to “AUTO”.
4 JAZZ CLUB
This mode creates the sound field of a live house with a low ceiling and hard walls. This mode gives jazz
a very vivid realism.
Select Dolby/DTS Surround.
5 VIDEO GAME
Use this to enjoy video game sources.
6 MATRIX
Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals consisting
of the component difference of the input signals (the component that provides the sense of expansion)
processed for delay are output from the surround channel.
7 VIRTUAL
Select this mode to enjoy a virtual sound field, produced from the front 2-channel speakers or headphones.
(Remote control unit)
Play a program source (DVD, etc.).
Depending on the program source being played, the effect may not be very noticeable.
In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes.
Press the CURSOR D button.
• Switch to the Audio Delay adjustment screen.
Press the CURSOR F or G button to set the
delay time (0 ms ~ 200 ms).
With a movie source, for example, adjust so that the
movement of the actors’ lips is synchronized with the
sound.
7
Select this when watching monaural movies for a greater sense of expansion.
3 ROCK ARENA
(Main unit)
4
5
6
MONO MOVIE
(NOTE)
The front left channel signals are output to the surround and surround back left channels, the front right
channel signals are output to the surround and surround back right channels, and the in-phase component
of the left and right channels is output to the center channel. Use this mode to enjoy stereo sound.
Press the ENTER button to complete the setting.
NOTE: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one channel (left or right),
so input signals to both channels. If you have a source component with only one audio output (monophonic camcorder, etc.)
obtain a “Y” adapter cable to split the mono output to two outputs, and connect to the L and R inputs.
2 Personal memory plus
This set is equipped with a personal memorize function that automatically memorizes the surround modes and input modes selected
for the different sources. When the input source is switched, the modes set for that source last time it was used are automatically
recalled.
The surround parameters, tone control settings and playback level balance for the different output channels are memorized for
each surround mode.
26
ENGLISH
ENGLISH
Basic Operation
Basic Operation
2 Operating the surround mode and the surround
parameters from the main unit‘s panel
SURROUND MODE
SURROUND
MODE
1
ENTER
SURROUND
PARAMETER
CURSOR
Turn the SELECT knob to select the surround
mode.
When turned clockwise:
DIRECT
STEREO
MONO MOVIE
SURROUND PARAMETER
SELECT
ROCK ARENA
2 To operate the surround mode and the surround
parameters from the remote control unit
3
Press the SURROUND PARAMETER button, and
press the CURSOR D or H button to select the
various parameters.
4
5
Press the CURSOR F or G button to adjust the
parameter settings.
Press the ENTER button to finish the surround
parameter mode.
(Remote control unit)
The surround mode switches in the following order each
time the DSP SIMULATION button is pressed:
MATRIX
2
ROCK ARENA
VIDEO GAME
JAZZ CLUB
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
JAZZ CLUB
Press the SURROUND PARAMETER button to
enter the surround parameter setting mode.
DTS NEO:6
VIDEO GAME
MATRIX
When turned counterclockwise:
DIRECT
STEREO
MONO MOVIE
Select the surround mode for the input channel.
MONO MOVIE
5CH/7CH STEREO
VIRTUAL SURROUND
DSP surround simulation
1
DOLBY PRO LOGIC IIx
ROCK ARENA
DOLBY PRO LOGIC IIx
5CH/7CH STEREO
JAZZ CLUB
VIRTUAL SURROUND
DTS NEO:6
VIDEO GAME
MATRIX
To select the surround mode while adjusting the surround
parameters, tone defeat or tone control, press the
SURROUND MODE button, then operate the selector.
2
Press and hold in the SURROUND PARAMETER
button to select the parameter you want to set.
The parameters which can be set differ for the different
surround modes are displayed. (Refer to “Surround modes
and parameters” (
page 60).)
3
Display the parameter you want to adjust, then
turn the SELECT knob to set it.
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
The surround parameter switches in the following order
each time the SURROUND PARAMETER button is pressed for
the different surround modes.
27
ENGLISH
ENGLISH
Basic Operation
Basic Operation
Room EQ setting
2 Operate the Room EQ from the remote control
unit
1
2 Operate the Room EQ from the main unit
2 Surround parameters r
1
ROOM SIZE:
This sets the size of the sound field.
There are five settings: “small”, “med.s” (medium-small),
“medium”, “med.l” (medium-large) and “large”. “small”
recreates a small sound field, “large” a large sound field.
• The surround parameter screen appears.
EFFECT LEVEL:
This sets the strength of the surround effect.
The level can be set in 15 steps from 1 to 15. Lower the level
if the sound seems distorted.
Press the CURSOR F or G button to select the
equalizer setting.
OFF
Manual
4
Press the SURROUND PARAMETER button to
select “Room EQ”.
Normal
Flat
Front
DELAY TIME:
The delay time can be set within the range of 0 to 110 ms only
in the matrix mode.
TONE CONTROL:
This can be set individually for each surround mode except
PURE DIRECT and DIRECT.
Press the CURSOR D or H button to select “Room
EQ”.
3
3
• The surround parameter screen is appears.
Press the SURROUND PARAMETER button.
2
2
Press the SURROUND PARAMETER button.
Turn the SELECT knob to select the equalizer
setting.
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
Press the ENTER button to finish surround
parameter mode.
• The equalizer setting of Normal, Flat, and Front can be selected
after performing the Auto Setup.
• When headphone is connected, the Room EQ cannot be used.
28
ENGLISH
ROOM EQ:
This sets the frequency response of each speaker.
• OFF:
The Equalizer is not used.
• Normal:
Adjust the frequency response of all speaker suitable for
general surround system.
• Flat:
Adjust the frequency response of all speakers flat.
• Front:
Adjusts the characteristics of each speaker to the
characteristics of the front speakers.
• Manual:
Selects the setting value that was set in the Manual EQ setup.
ENGLISH
Basic Operation
Basic Operation
TONE CONTROL
SELECT
CH SELECT
CURSOR G
CURSOR F
TONE DEFEAT
Tone control setting
Channel Level
2 Adjusting the sound quality (tone)
The tone control function will not work in the PURE DIRECT or
DIRECT mode.
1
Press the TONE CONTROL button.
The tone switches as follows each time the TONE CONTROL
button is pressed.
BASS
2
You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
1
Press the CH SELECT button to select the
speaker whose level you want to adjust.
The channel switches as shown below each time the button
is pressed.
FL
C
FR
SR
SW
SL
SBL
SBR
TREBLE
Turn the SELECT knob to adjust the level of the
bass or treble.
To increase the bass or treble:
Turn the control clockwise. (The bass or treble sound can be
increased up to +6 dB in steps of 1 dB.)
To decrease the bass or treble:
Turn the control counterclockwise. (The bass or treble sound
can be decreased down to –6 dB in steps of 1 dB.)
2 Tone defeat mode
If you do not want the bass and treble to be adjusted, turn on the
tone defeat mode.
When the surround back speaker setting is set to “1sp” for
“Speaker Configuration”, this is set to “SB”.
“SB” appears only when the “Power Amp Assign.” setting
is the surround back mode.
2
Press the CURSOR F or G button to adjust the
level of the selected speaker.
The default setting of the channel level is 0 dB.
The level of the selected speaker can be adjusted within the
range of +12 to –12 dB by pressing the CURSOR buttons.
The SW channel level can be turned off by decreasing it one
step from –12 dB.
OFF ´ –12 dB ´ +12 dB
Press the TONE DEFEAT button.
The signals do not pass through the bass and treble
adjustment circuits, thus resulting in higher quality sound.
29
ENGLISH
ENGLISH
Basic Operation
FUNCTION
ON/STANDBY
Basic Operation
BAND
POWER
Auto tuning
PRESET •
TUNER
TUNING
MODE
BAND
TUNING
Listening to the radio
Auto preset memory
• This unit is equipped with a function for automatically searching
for FM broadcast stations and storing them in the preset
memory.
• The “Auto tuner preset” operation can also be performed at
“System setup” (
page 43).
Hold the PRESET • button and press the POWER
switch on the main unit.
• The unit automatically begins searching for FM broadcast
stations.
When the first FM broadcast station is found, that station is
stored in the preset memory at channel A1.
Subsequent stations are automatically stored in order at
preset channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1
to E8, F1 to F8 and G1 to G8 for a maximum of 56 stations.
Channel A1 is tuned in after the auto preset memory
operation is completed.
1
Set the input source to “TUNER”.
(Main unit)
(Remote control unit)
2
3
Watching the display, press the BAND button to
select the desired band (AM or FM).
4
Press the TUNING (+) or (–) button.
Press the MODE button to set the auto tuning
mode.
2 DEFAULT SETTINGS
A1 ~ A8
B1 ~ B8
C1
D1
E1
F1
G1
~
~
~
~
~
C8
D8
E8
F8
G8
Auto tuner presets
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 /
90.1 / 90.1 MHz
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
Automatic searching begins, then stops when a station is
tuned in.
• When in the auto tuning mode on the FM band, the “STEREO”
indicator lights on the display when a stereo broadcast is tuned
in. At open frequencies, the noise is muted and the “TUNED”
and “STEREO” indicators turn off.
• If an FM station cannot be preset automatically due to poor
reception, use the “Manual tuning” operation to tune in the
station, then preset it using the manual “Preset memory”
operation.
• To interrupt this function, press the ON/STANDBY switch.
30
ENGLISH
ENGLISH
Basic Operation
Basic Operation
Checking the preset stations
FUNCTION BAND PRESET STATUS
TUNING
TUNER
BAND
MEMORY
PRESET
MODE
SHIFT
The preset (broadcast) stations can be checked on the on screen
display.
Press the ON SCREEN button repeatedly until the
“Tuner Preset Stations” screen appears on the OSD.
ON SCREEN
SHIFT
TUNING
Manual tuning
1
2
3
Set the input source to “TUNER”.
Watching the display, press the BAND button to
select the desired band (AM or FM).
Press the MODE button to set the manual tuning
mode.
Check that the display’s “AUTO” indicator turns off.
4
Press the TUNING (+) or (–) button to tune in
the desired station.
The frequency changes continuously when the button is
held in.
• When the manual tuning mode is set, FM stereo broadcasts are
received in monaural and the “STEREO” indicator turns off.
Preset stations
1
Use the “Auto tuning” or “Manual tuning”
operation to tune in the station to be preset in
the memory.
2
3
4
5
Press the MEMORY button.
Press the SHIFT button and select the desired
memory block (A to G).
Press the PRESET (+) or (–) button to select the
desired preset channel (1 to 8).
Press the MEMORY button again.
• Store the station in the preset memory.
• To preset other channels, repeat steps 1 to 4.
A total of 56 broadcast stations can be preset — 8 stations
(channels 1 to 8) in each of blocks A to G.
31
ENGLISH
Recalling preset stations
1
2
Watching the display, press the SHIFT button to
select the preset memory block.
Watching the display, press the PRESET • (+) or
ª (–) button to select the desired preset channel.
ENGLISH
Basic Operation
XM Satellite Radio
2 Introducing XM Satellite Radio
There’s a world of audio listening pleasure beyond AM and FM.
XM Satellite Radio. Select from over 150 channels of music,
news, sports, comedy, talk, and entertainment. Coast-to-coast
coverage. Digital quality sound. With all music channels 100%
commercial free.
Questions?: Visit www.xmradio.com.
2 How to subscribe
Listeners can subscribe by visiting XM on the Web at
www.xmradio.com or by calling XM’s Listener Care at (800) 9672346.
Customers should have their Radio ID and credit card ready. The
Radio ID can be found by selecting channel 0 on the radio.
Basic Operation
Checking the XM signal strength and Radio ID
1
2
3
Hardware and required basic monthly subscription sold
separately. Premium Channel available at additional monthly
cost.
Installation costs and other fees and taxes, including a onetime activation fee may apply. Subscription fee is consumer
only.
All fees and programming subject to change. Subscriptions
subject to Customer Agreement available at xmradio.com.
Only available in the 48 contiguous United States. ©2005 XM
Satellite Radio Inc. All rights reserved. All other trademarks
are the property of their respective owners.
Watching the display, press the BAND button to
select the XM mode.
Press the STATUS button until “SIGNAL” is
displayed.
• The display changes as shown below according to the
receiving condition.
Display
GOOD
MARGINAL
WEAK
NO
2 A warning against reverse engineering
It is prohibited to copy, decompile, disassemble, reverse
engineer, or manipulate any technology incorporated in receivers
compatible with the XM Satellite Radio system.
Furthermore, the AMBE® voice compression software included
in this product is protected by intellectual property rights
including patent rights, copyrights, and trade secrets of Digital
Voice Systems, Inc. The user of this or any other software
contained in an XM Radio is explicitly prohibited from attempting
to copy, decompile, reverse engineer, or disassemble the object
code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this
product.
Set the input source to “TUNER”.
4
5
6
Condition
Signal strength is good
Signal strength is marginal
Signal strength is poor
Loss of the signal
Adjust the antenna location until “SIGNAL:
GOOD” is displayed.
Press the STATUS button until the XM channel
(ex.XM001) is displayed.
Channel selection
1
2
3
DeepTrks
Channel name
The channel changes continuously when you press and hold
the TUNING button.
Category search
1
Press the CURSOR F or G button in the XM
mode.
• The current category name is displayed.
CAT:
2
Radio ID
Press the TUNING (+) or (–) button to reach the
desired channel.
Channel number
• The Radio ID is displayed.
¡¡¡¡¡¡¡¡
Watching the display, press the BAND button to
select the XM mode.
XM040
Press the TUNING (–) button to select channel 0
(XM000).
XM000
Set the input source to “TUNER”.
Rock
Press the CURSOR F or G button to select the
category, and press the CURSOR D or H button
to select the channel within the selected
category.
• “LOADING” is displayed while receiving the channel or
information.
• “UPDATING” is displayed while updating encryption code.
• When the selected channel is not available, “XM– – –” is
displayed.
• Information on the artist name, song title, category and signal
level can be checked using the STATUS button on the main unit.
• The XM Satellite Radio channels can be preset in the same way
as AM/FM band.
Please refer to “Preset stations” and “Recalling preset
stations” (
page 31).
32
ENGLISH
ENGLISH
Advanced Operation
Advanced Operation
OFF
ON SOURCE
3. Tuner system buttons
1. CD player (CD), CD recorder and MD recorder (CDR/MD)
system buttons
NUMBER
MODE 1
MODE 2
Remote control unit
Operating DENON audio components
6, 7
2
1
8, 9
3
DISC SKIP +
:
:
:
:
:
:
Manual search (forward and reverse)
Stop
Play
Auto search (cue)
Pause
Switch discs (for CD changers only)
2. Tape deck (TAPE) system buttons
1
Set the MODE 1 switch to “AUDIO”.
2
Set the MODE 2 switch to the position for the
component to be operated (CD, CDR/MD or
TAPE).
6
7
2
1
0
A/B
3
:
:
:
:
:
:
Rewind
Fast-forward
Stop
Forward play
Reverse play
Switch between decks A and B
Operate the audio component.
For details, refer to the component’s operating instructions.
While this remote control is compatible with a wide range of
infrared controlled components, it may be the case that
some component models cannot be operated with this
remote control.
33
ENGLISH
SHIFT
CHANNEL +, –
TUNING +, –
BAND
MODE
MEMORY
:
:
:
:
:
:
Switch preset channel range
Preset channel up/down
Frequency up/down
Switch between the AM and FM bands
Switch between auto and mono
Preset memory
• TUNER can be operated when the switch is at “AUDIO”
position.
ENGLISH
Advanced Operation
Advanced Operation
Preset memory
• DENON and other makes of components can be operated by
setting the preset memory.
• This remote control unit can be used to operate components of
other manufacturers without using the learning function by
registering the manufacturer of the component as shown in the
list of preset codes (
End of this manual).
• Operation is not possible for some models.
1
Set the MODE 1 switch to “AUDIO” or “VIDEO”.
Set to the AUDIO side for the CD, Tape deck or CDR/MD
position, and to the VIDEO side for the DVD/VDP,
DBS/CABLE, VCR or TV position.
2
Set the MODE 2 switch to the component to be
registered.
1. Digital video disc player (DVD) system buttons
• The signals for the pressed buttons are emitted while setting
the preset memory. To avoid accidental operation, cover the
remote control unit’s transmitting window while setting the
preset memory.
• Depending on the model and year of manufacture, this function
cannot be used for some models, even if they are of makes
listed in the list of preset codes.
• Some manufacturers use more than one type of remote control
code. Refer to the included list of preset codes to change the
number and verify correct operation.
• The preset memory can be set for one component only among
the following: CDR/MD, DVD/VDP and DBS/CABLE.
2 The
preset codes are as follows upon shipment from the
factory and after resetting:
• TV, VCR .........................................HITACHI
• CD, TAPE.......................................DENON
• CDR/MD ........................................DENON (CDR)
• DVD/VDP .......................................DENON (DVD)
• DBS/CABLE...................................ABC (CABLE)
Operating a component stored in the preset
memory
3
Press the ON/SOURCE and OFF button at the
same time.
4
Referring to the included list of preset codes,
press the NUMBER buttons to input the preset
code (a 3-digit number) for the manufacturer of
the component whose signals you want to store
in the memory.
5
• The indicator starts flashing.
To store the codes of another component in the
memory, repeat steps 1 to 4.
1
Set the MODE 1 switch to “AUDIO” or “VIDEO”.
Set to the AUDIO side for the CD, Tape deck or CDR/MD
position, and to the VIDEO side for the DVD/VDP,
DBS/CABLE, VCR or TV position.
2
Set the MODE 2 switch to the component you
want to operate.
3
Operate the component.
For details, refer to the component’s operating instructions.
Some models cannot be operated with this remote control
unit.
34
ENGLISH
ON/SOURCE : Power on/standby
OFF
: DENON DVD power off
6, 7
: Manual search (forward and reverse)
2
: Stop
1
: Play
8, 9
: Auto search (to beginning of track)
3
: Pause
0 ~ 9, +10
: Number
DISC SKIP + : Disc skip (for DVD changer only)
DISPLAY
: Switch display
MENU
: Menu
RETURN
: Return
SETUP
: Setup
•, ª, 0, 1 : Cursor up, down, left and right
ENTER
: Enter setting
• Some manufacturers use different names for the DVD remote
control buttons, so also refer to the instructions on remote
control for that component.
ENGLISH
Advanced Operation
2. Video disc player (VDP) system buttons
ON/SOURCE : Power on/standby
6, 7
: Manual search (forward and reverse)
2
: Stop
1
: Play
8, 9
: Auto search (cue)
3
: Pause
0 ~ 9, +10
: Number
Advanced Operation
3. Video deck (VCR) system buttons
ON/SOURCE : Power on/standby
6, 7
: Manual search (forward and reverse)
2
: Stop
1
: Play
3
: Pause
Channel +, – : Channel up/down
35
ENGLISH
4. Digital broadcast satellite (DBS) tuner and
cable (CABLE) system buttons
ON/SOURCE
MENU
RETURN
•, ª, 0, 1
ENTER
CHANNEL +, –
0 ~ 9, +10
DISPLAY
VOL +, –
:
:
:
:
:
:
:
:
:
Power on/standby
Menu
Return
Cursor up, down, left and right
Enter
Channel up/down
Number
Switch display
Volume up/down
ENGLISH
Advanced Operation
Advanced Operation
5. Monitor TV (TV) system buttons
MAIN ON
ZONE2 OFF
NUMBER
MODE 1
MODE 2
Punch through
“Punch Through” is a function allowing you to operate the PLAY,
STOP, MANUAL SEARCH and AUTO SEARCH buttons on CD, TAPE,
CDR/MD, DVD/VDP or VCR components when in the
DBS/CABLE or TV mode. By default, nothing is set.
ON/SOURCE
MENU
RETURN
•, ª, 0, 1
ENTER
CHANNEL +, –
0 ~ 9, +10
DISPLAY
TV/VCR
VOL +, –
:
:
:
:
:
:
:
:
:
:
Power on/standby
Menu
Return
Cursor up, down, left and right
Enter
Channel up/down
Number
Switch display
Switch between TV and video player
Volume up/down
• For CD, CDR, MD and TAPE components, the buttons can be
operated in the same way as for DENON audio components
(
page 33).
• A TV can be operated when the switch is at the DVD/VDP, VCR,
TV position.
1
Set the MODE 1 switch to “VIDEO”.
2
Set the MODE 2 switch to the component to be
registered (DBS/CABLE or TV).
3
Press the ZONE2 OFF and MAIN ON buttons at
the same time.
4
Input the number of the component you want to
set.
• The indicator starts flashing.
No.
1
2
3
4
5
0
CD
TAPE
CDR/MD
DVD/VDP
VCR
No setting
36
ENGLISH
ENGLISH
Advanced Operation
Advanced Operation
Multi zone music entertainment system
• When the outputs of the ZONE2 OUT terminals are wired and connected to integrated amplifiers installed in other rooms, different
sources can be played in rooms other than the MAIN ZONE in which this unit and the playback devices are installed.
• ZONE2 speaker out and pre-out can be used when “ZONE2” is selected at “Power Amp Assign.” in the “System Setup” menu.
In this case, surround back speaker out cannot be used for MAIN ZONE.
• When a sold separately room-to-room remote control unit (DENON RC-616, 617 or 618) is wired and connected between the MAIN
ZONE and ZONE2, the remote-controllable devices in the MAIN ZONE can be controlled from ZONE2 using the remote control unit.
• For the AUDIO outputs, use high quality pin-plug cables and wire in such a way that there is no humming or noise.
• For instructions on installation and operation of separately sold devices, refer to the devices’ operating instructions.
• When the main unit is set to the recording output mode, ZONE2 remote control button cannot be operated.
2 When using the SURR.BACK/ZONE2 amplifier as the ZONE2
• The SPEAKER OUT and PRE OUT terminals can be used simultaneously in ZONE2.
• To use the ZONE2, turn on the ZONE2 button.
• The output of the ZONE2 SPEAKER OUT terminals can be adjusted with the remote control unit’s ZONE2 VOLUME button.
[System configuration and connections example]
Using this unit’s internal amplifier as the ZONE2.
MAIN ZONE 5.1-channel systems
Monitor
FL
ZONE2
FR
C
This unit
DVD player
B
SW
Input
RC-617
ZONE2 SPEAKER OUT
SL
RC-616
SR
SYSTEM REMOTE
CONTROL UNIT RC-1015
PROGRAMMABLE
REMOTE CONTROL UNIT
: ROOM-TO-ROOM REMOTE CONTROL SYSTEM
(separately sold) control line
: SPEAKER cable
Refer to “Connections” (
37
ENGLISH
page 17).
ENGLISH
Advanced Operation
Advanced Operation
ZONE2 OFF
FUNCTION ZONE2/REC SELECT
ZONE2 ON
FUNCTION
CHANNEL
MODE 1
MODE 2
VOLUME
ZONE2
Outputting a program source to amplifier,
etc., in a different room (ZONE2 mode)
1
Press the ZONE2/REC SELECT button to display
the “ZONE2 SOURCE” on the display.
Remote control unit operations during
multi-source playback (selecting the source)
1
Set the MODE 1 switch to the “AUDIO”.
2
Set the MODE 2 switch to the “ZONE2”.
3
Press the ZONE2 ON button.
The display switches as follows each time the button is
pressed.
ZONE2
2
3
REC
Turn the FUNCTION knob to select the source
you want to output appears on the display.
Start playing the source to be output.
For operating instructions, refer to the manuals of the
respective components.
To cancel, turn the FUNCTION knob and select “SOURCE”.
4
Press the ZONE2 button.
Lights
To cancel the ZONE2 mode:
Press the ZONE2 OFF button.
4
Press the FUNCTION button.
The ZONE2 source switches directly.
• The signals of the source selected in the ZONE2 mode are also
output from the VCR-1, VCR-2 and CDR/TAPE recording output
terminals.
• Digital signals are not output to the ZONE2 output terminals.
5
The output level of the ZONE2 SPEAKER OUT
terminals can be controlled pressing the
VOLUME button on the remote control unit.
Default setting (ZONE2 VOLUME LEVEL):
– – – dB (MINIMUM)
38
ENGLISH
6
When the ZONE2 SOURCE function is set to
TUNER, the preset channel can be selected
using the CHANNEL button on the remote
control unit.
This is only possible when the main unit in the ZONE2 mode
(
page 45).
ENGLISH
Advanced Operation
Advanced Operation
Initialization of the microprocessor
FUNCTION ZONE2/REC SELECT
POWER
If the indication on the display is not normal or if the operation of
the unit is not correct, then the microprocessor should be reset
by the following procedure.
SPEAKER
Other functions
Playing one source while recording another
(REC OUT mode)
1
Press the ZONE2/REC SELECT button to display
the “RECOUT SOURCE” on the display.
The display switches as follows each time the button is
pressed.
ZONE2
2
3
REC
1
2
Switch off the unit using the main unit’s
POWER switch.
3
Check that the entire display is flashing at 1second intervals and release the buttons.
Keep both SPEAKER A and B buttons depressed
and turn on the unit by pressing the main unit’s
POWER switch.
• The microprocessor will be initialized.
Last function memory
• This unit is equipped with a last function memory which stores
the input and output setting conditions as they were
immediately before the power is switched off.
This function eliminates the need to perform complicated
resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function
provides approximately one week of memory storage when the
main unit’s POWER switch is off and the power supply cord
disconnected.
Turn the FUNCTION knob to select the source
you want to output appears on the display.
Set the recording mode.
For operating instructions, refer to the manual of the
component on which you want to record.
To cancel, turn the FUNCTION knob and select “SOURCE”.
• Recording sources other than digital inputs selected in the REC
OUT mode are also output to the ZONE2 audio output
terminals.
• Digital signals are not output to the REC SOURCE or audio
output terminals.
• The DIGITAL IN’s signal selected with the FUNCTION knob is
output to the DIGITAL OUT (OPTICAL) terminal.
39
ENGLISH
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from
the factory).
ENGLISH
Advanced Setup – Part 1
On screen display and front display
Advanced Setup – Part 1
The AVR-886 is equipped with an intuitive and easy-to-understand on screen display, and is
equipped with an alphanumeric front panel display that can also be used to check and adjust
settings. We recommend that you use the on screen display when you make system adjustments.
Some representative front display and on screen display examples are shown below.
Use System Setup to customize a variety of settings to suit your listening environment.
For the contents of a system menu and the initial setting of this unit (
page 52, 53).
Navigating through the System Setup Menu
[ On screen display ]
You can change the settings using the buttons on the remote control unit.
Top menu
[ Front display ]
MODE 1
Top menu
ENTER
SETUP
CURSOR
1
2
Screen title
No.
*Auto Setup/EQ
Sub-menu title
*Speaker Setup
To select a menu, press the
CURSOR D or H button.
[ On screen display ]
2
[ Display ]
Set the MODE 1 switch to “AUDIO”.
*Input Setup
Press the SETUP button to display
the “System Setup” menu.
Press the CURSOR D or H button
to select the menu, then press the
ENTER button.
Main menu
3
Screen title
Main menu
No.
*Digital In
Sub-menu title
*Digital In
3
4
5
6
Press the ENTER button to enter
the selected menu.
4
To change a setting, first select it
pressing the CURSOR D or H
button, and then change the
setting pressing the CURSOR F or
G button.
Press the ENTER button to confirm
the new settings.
*AutoSet <Start
*COAX1
Currently selected line
CD
Current setting
6
Currently selected line
*COAX1
Press the SETUP button to return
to the “System Setup” menu and
again to return to the main screen.
Press the CURSOR F button
to execute.
*Exit
40
ENGLISH
CD
ENGLISH
Advanced Setup – Part 1
Advanced Setup – Part 1
Input Setup
Setting the Input Function Level
Setting the Digital In Assign.
This setting assigns the digital input terminals of the AVR-886 for
the different input sources.
1
Press the CURSOR D or H button to select
“Input Setup” at the “System Setup” menu,
then press the ENTER button.
• The “Input Setup” menu appears.
• The OPTICAL 3 terminal on the AVR-886’s rear panel is
equipped with an optical digital output terminal for recording
digital signals on a CD recorder, MD recorder or other digital
recorder. Use this for digital recording between a digital audio
source (stereo – 2 channels) and a digital audio recorder.
• Do not connect the output of the component connected to the
OPTICAL 3 OUT terminal on the AVR-886’s rear panel to any
terminal other than the OPTICAL 3 IN terminal.
• “PHONO”, “TUNER” and “V. AUX” cannot be selected with
“Setting the Digital In Assign.”.
• Correct the playback level of the different input sources.
• Adjust the playback levels of the devices connected to the
different input sources to the same level to eliminate the need
for adjusting the main volume each time the input source is
switched.
1
Press the CURSOR D or H button to select
“Input Function Level” at the “Input Setup”
menu, then press the ENTER button.
• The “Input Function Level” screen appears.
Setting the Ext In SW Level
Set the method of playback of the analog input signal connected
to the Ext. In Subwoofer.
2
Press the CURSOR D or H button to select
“Digital In Assign.”, then press the ENTER
button.
1
Press the CURSOR D or H button to select “Ext
In SW Level” at the “Input Setup” menu, then
press the ENTER button.
2
• The “Ext In SW Level” screen appears.
• The “Digital In Assign.” screen appears.
Press the CURSOR D or H button to select the
input source, then press the CURSOR F or G
button to adjust the level.
The level can be adjusted between –12 dB and +12 dB in
units of 1 dB.
If “Yes” is selected for “Default”, the settings are
automatically reset to the default values.
3
3
Press the CURSOR D or H button to select the
digital input terminal, then press the CURSOR
F or G button to select the input source.
Select “OFF” for input sources for which no digital input
terminals are used.
If “Yes” is selected for “Default”, the settings are automatically
reset to the default values.
4
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
2
Press the CURSOR F or G button to select
according to the specifications of the player
being used.
Also refer to the player’s operating instructions.
+15dB (default) recommended (0, +5, +10 or +15 can be
selected).
3
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
41
ENGLISH
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
• After completing this setting, check that the playback levels for
the different sources are the same.
ENGLISH
Advanced Setup – Part 1
Setting the Function Rename
The names of the input sources displayed on the front display
and the on screen display can be changed. The names or brands
of the devices connected to the input sources can be input.
1
Press the CURSOR D or H button to select
“Function Rename” at the “Input Setup” menu,
then press the ENTER button.
Advanced Setup – Part 1
4
Repeat step 3 to complete input of the input
source name.
If you wish to return the input source to its initial setting,
press the CURSOR H button while the input source is
highlighted.
If “Yes” is selected for “Default”, the setting is automatically
reset to the default name.
Setting the Component In Assign.
This setting assigns the color difference (component) video input
terminals of the AVR-886 for the different input sources.
1
Press the CURSOR D or H button to select
“Component In Assign.” at the “Input Setup”
menu, then press the ENTER button.
• The “Component In Assign.” screen appears.
• The “Function Rename” screen appears.
2
Press the CURSOR D or H button to select the
input source whose name you want to change,
then press the CURSOR F or G button.
• The screen switches to the character input screen.
Example:
When “CD” is selected and the CURSOR F or G button
is pressed
5
Once all the characters have been input, press
the ENTER button.
• The “Function Rename” screen appears.
Use the same procedure to change other input source
names as well.
6
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
• When the input source is selected, the display is as shown
below.
Example:
When the name has been changed to “DENON”
3
Press the CURSOR F or G button to move the
cursor ( 2 ) to the character, number, symbol or
punctuation mark you wish to input, and press
the CURSOR D or H button to select that
character.
ABCDEFGHIJKLMNOPQRSTUVWXY
Zabcdefghijklmnopqrstuvwxyz
0123456789
’ ( ) + , – . / : ; < = > ? [ ] (space)
Up to 5 characters can be input.
42
ENGLISH
2
Press the CURSOR D or H button to select the
component video input terminal, then press the
CURSOR F or G button to select the input
source.
Select “OFF” for sources for which the component (Y,
PB/CB and PR/CR) video input is not to be used.
When the default, “Yes”, is selected, the settings are reset
to the factory defaults.
3
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
ENGLISH
Advanced Setup – Part 1
Advanced Setup – Part 1
Setting the Video Input Mode
Select the input signal to be output to the composite S-Video and
component monitor output terminals using the video conversion
function.
1
Press the CURSOR D or H button to select
“Video Input Mode” at the “Input Setup”
menu, then press the ENTER button.
• The “Video Input Mode” screen appears.
AUTO:
When there are multiple input signals, the input signals are
detected and the input signal to be output from the video
monitor output terminal is selected automatically in the
following order: component video, S-Video, composite video.
Component:
The signal connected to the component video terminal is
always played.
Video conversion is not conducted, so no image is output
from the monitor output terminal when there is no input
signal to the component terminal.
Setting the Auto Tuner Preset
Use this to automatically search for FM broadcasts and store up
to 56 stations at preset channels A1 to 8, B1 to 8, C1 to 8, D1 to
8, E1 to 8, F1 to 8 and G1 to 8.
1
Press the CURSOR D or H button to select
“Auto Tuner Preset” at the “Input Setup” menu,
then press the ENTER button.
• The “Auto Tuner Preset” screen appears.
S-Video:
The signal connected to the S-Video terminal is always played.
The S-Video input signal is converted and output from the
composite and component monitor output terminal.
2
Press the CURSOR D or H button to select the
input source for which you want to set the video
input mode.
3
Press the CURSOR F or G button to select the
Video:
The signal connected to the composite video terminal is
always played.
The composite video input signal is up-converted and output
from the S-Video and component monitor output terminals.
4
Press the ENTER button to enter the setting.
• The “Input Setup” menu appears.
mode as below.
The details in each mode are as follows.
AUTO
Component
S-Video
Video
• Down-converting from the component video signal to the SVideo and composite video signal is not possible, so when not
using the component video monitor output terminal connect
the player using the S-Video or composite video input terminal
(
page 12).
43
ENGLISH
2
3
Press the CURSOR F button to select “Start”.
• “Search” appears on the screen and searching begins.
• “Completed” appears once searching is completed.
Press the CURSOR D or H button to select
“Exit”, then press the ENTER button.
• The “System Setup” menu appears.
ENGLISH
Advanced Setup – Part 1
Advanced Setup – Part 1
Advanced playback
Setting the Auto Surround Mode
Setting the Audio Delay
• When watching a DVD or other video source, the picture on the
monitor may seem delayed with respect to the sound. In this
case, adjust the audio delay to delay the sound and synchronize
it with the picture.
• The audio delay setting is stored separately for each input
source.
1
• The audio delay setting does not apply when playing in the EXT.
IN mode or in the analog input direct mode, pure direct or
stereo mode (TONE DEFEAT “ON”).
Press the CURSOR D or H button to select
“Advanced Playback” at the “System Setup”
menu, then press the ENTER button.
• The “Advanced Playback” menu appears.
The surround mode used last for the three types of input signals
shown below is stored in the memory, and the signal is
automatically played with that surround mode the next time it is
input.
Note that the surround mode setting is also stored separately for
the different input sources.
q Analog and PCM 2-channel signals (STEREO)
w 2-channel signals in the Dolby Digital, DTS or another multichannel format (DOLBY PLIIx Cinema)
e Multi-channel signals in the Dolby Digital, DTS or another
multi-channel format (DOLBY/DTS SURROUND)
Default settings are indicated in ( ).
During playback in the PURE DIRECT mode, the surround
mode does not change even if the input signal is changed.
1
Press the CURSOR D or H button to select “Auto
Surround Mode” at the “Advanced Playback”
menu, then press the ENTER button.
• The “Auto Surround Mode” screen appears.
2
3
Press the CURSOR D or H button to select
“Audio Delay”, then press the ENTER button.
• The “Audio Delay” screen appears.
Press the CURSOR F or G button to set the
delay time (0 ms ~ 200 ms).
With a movie source, for example, adjust so that the
movement of the actors’ lips is synchronized with the
sound.
4
Press the ENTER button to enter the setting.
• The “Advanced Playback” menu appears.
44
ENGLISH
2
Press the CURSOR F or G button to select “ON”
if you want to use the auto surround mode, or
“OFF” if you do not want to use it.
3
4
Press the ENTER button to enter the setting.
• The “Advanced Playback” menu appears.
Press the CURSOR D or H button to select
“Exit”, then press the ENTER button.
• The “System Setup” menu appears.
ENGLISH
Advanced Setup – Part 1
Advanced Setup – Part 1
Option Setup
Setting the Muting Level
This sets the amount of attenuation applied for audio output
muting.
1
Press the CURSOR D or H button to select
“Option Setup” at the “System Setup” menu,
then press the ENTER button.
Setting the Power Amp Assign.
Setting the On Screen Display (OSD)
• Use this to turn the on screen display (messages other than the
menu screens) “ON” or “OFF”.
• Sets the on screen display mode.
1
• The “Option Setup” menu appears.
Press the CURSOR D or H button to select “On
Screen Display” at the “Option Setup” menu,
then press the ENTER button.
• The “On Screen Display” screen appears.
Make this setting to switch the power amplifier for the surround
back channel to ZONE2 or Bi-Amp.
Power Amp
Assign.
Surround back
ZONE2
Bi-Amp
1
SPEAKER OUT
MAIN ZONE
ZONE2
7.1ch system
–
5.1ch system 2ch system
–
5.1ch system
PRE-OUT
S.BACK/ZONE
Surround back
ZONE2
–
Press the CURSOR D or H button to select
“Power Amp Assign.” at the “Option Setup”
menu, then press the ENTER button.
• The “Power Amp Assign.” screen appears.
2
Press the CURSOR D or H button to select
“Muting Level” at the “Option Setup” menu,
then press the ENTER button.
• The “Muting Level” screen appears.
2
3
Press the CURSOR F or G button to select “ON”
or “OFF”.
Press the CURSOR D or H button to select the
on screen display mode, then press the CURSOR
F or G button to select “MODE1” or
“MODE2”.
MODE1:
Prevents flickering of the on screen display when there is no
video signal.
3
Press the CURSOR F or G button to select the
desired setting.
–20 dB:
Attenuation of the volume by –20 dB from the present level.
–40 dB:
Attenuation of the volume by –40 dB from the present level.
– – – dB:
The volume level is completely muted.
4
MODE2:
Flickering is not prevented.
Use this mode if the on screen display does not appear in
MODE1, which may happen depending on the TV being used.
4
Press the ENTER button to enter the setting.
• The “Option Setup” menu appears.
Press the ENTER button to enter the setting.
• The “Option Setup” menu appears.
45
ENGLISH
2
Press the CURSOR F or G button to select the
Amp Assign mode according to the speaker
system you want to set up.
3
Press the ENTER button to enter the setting.
• The “Option Setup” menu appears.
ENGLISH
Advanced Setup – Part 1
Setting the Setup Lock
The system setup settings can be locked so that they cannot be
changed easily.
1
Press the CURSOR D or H button to select
“Setup Lock” at the “Option Setup” menu, then
press the ENTER button.
Advanced Setup – Part 2
This Speaker Setup section describes the procedures to make
speaker settings manually (without using the Auto Setup
function), as well as to make manual changes to settings that
have already been made by the Auto Setup function.
ENTER
CURSOR
• The “Setup Lock” screen appears.
Speaker Setup
Setting the Speaker Config.
2
3
Press the CURSOR F button to select “ON”, to
lock the system setup settings.
The composition of the signals output to each channel and the
frequency response are adjusted automatically according to the
combination of speakers actually being used.
Press the ENTER button to finalize the setting
and exit the system setup mode.
1
3
Press the CURSOR D or H button to select
“Speaker Setup” at the “System Setup” menu,
then press the ENTER button.
Center Sp.
Front Sp.
Subwoofer
Surround Sp.
• The “Speaker Setup” menu appears.
• When the setup lock function is activated, the settings listed
below cannot be changed, and “SETUP LOCKED” is displayed
when related buttons are operated.
• System setup settings
• Surround parameter settings
• Tone control settings
• Channel level settings (including test tones)
• To unlock, press the SETUP button again and display the “Setup
Lock” screen, then select “OFF” and press the ENTER button.
• System setup is complete. Once these settings are made,
there is no need to change them unless different AV components
are connected or the speakers are repositioned.
Press the CURSOR D or H button to select a
speaker, then press the CURSOR F or G button
to select a parameter.
Surround back Sp.
4
2
Press the CURSOR D or H button to select
“Speaker Config.”, then press the ENTER button.
• The “Speaker Config.” screen appears.
46
ENGLISH
Press the ENTER button to enter the setting.
• The “Speaker Setup” menu appears.
• Select “Large” or “Small” not according to the actual size of
the speaker but according to the speaker’s capacity for playing
low frequency (bass sound below the frequency set for the
Crossover Frequency) signals. If you are unsure, try comparing
the sound at both settings (setting the volume to a level low
enough so as not to damage the speakers) to determine the
proper setting.
ENGLISH
Advanced Setup – Part 2
2 Parameters
Large:
Select this when using speakers that have sufficient ability to
reproduce bass sound below the frequency set for the
crossover frequency mode.
Small:
Select this when using speakers that do not have sufficient
ability to reproduce bass sound below the frequency set for the
crossover frequency mode. When this is set, bass sound with
a frequency below the frequency set for the crossover
frequency mode is sent to the subwoofer.
Advanced Setup – Part 2
Setting the Delay Time
Input the distance between the listening position and each
speaker to set the delay time for the surround playback.
Preparations:
Measure the distances between the listening position and the
speakers.
FL
Center
Subwoofer
None:
Select this when no speakers are installed.
If the subwoofer has sufficient low frequency playback
capacity, good sound can be achieved even when “Small” is
set for the front, center and surround speakers.
Press the ENTER button to enter the setting.
• The “Speaker Setup” menu appears.
Setting the Channel Level
• Use this setting to balance the playback levels in different
channels and make them appear equal.
• From the listening position, listen to the test tones produced
from the speakers to adjust the level.
• The levels can also be adjusted directly from the remote control
unit (
page 48).
Listening position
Yes / No:
Select “Yes” when a subwoofer is installed, “No” when a
subwoofer is not installed.
2sp / 1sp:
Set the number of speakers to be used for the surround back
channel.
FR
4
SL
SR
SBL
1
1
SBR
Press the CURSOR D or H button to select
“Channel Level” at the “Speaker Setup” menu,
then press the ENTER button.
• The “Channel Level” screen appears.
Press the CURSOR D or H button to select
“Delay Time” at the “Speaker Setup” menu,
then press the ENTER button.
• The “Delay Time” screen appears.
2
Press the CURSOR F or G button to select
“Auto” or “Manual”.
Auto:
Adjust the level while listening to the test tones produced
automatically from each speaker.
2
3
Press the CURSOR D or H button to select the
speaker to be set.
Press the CURSOR F or G button to set the
distance between the speaker and the listening
position.
The distance changes in units of 1 foot each time the button
is pressed. Select the value closest to the measured
distance.
If “Yes” is selected for “Default”, the settings are
automatically reset to the default values.
The difference in distance for the various speaker
settings must not be greater than 20 ft.
47
ENGLISH
Manual:
Select the speaker from which you want to produce the test
tone to adjust the level.
3
Press the CURSOR D or H button to select
“TEST TONE Start”, then press the CURSOR F
button to select “Start”.
ENGLISH
Advanced Setup – Part 2
4
-1
When “Auto” mode is selected:
Press the CURSOR F or G button to adjust all
the speakers to the same volume.
• The test tones are emitted from each speaker in the
following order: at 4-second intervals during the first and
second cycle, and at the 2-second intervals during the
third and subsequent cycles.
FL
C
SR
FR
2sp
SW
SL
SBL
SBR
SB
1sp
When the surround back speaker setting is set to
“1sp” for “Speaker Configuration”, this is set to “SB”.
Example:
When the volume is set to –12.0 dB while the test tone
is being produced from the Front Lch speaker
Setting the Crossover Frequency
• To cancel the settings, press the CURSOR H button to select
“Level Clear” on the “Channel Level” screen, then make the
settings again.
• When adjusting the level of an active subwoofer system, you
may also need to adjust the subwoofer’s own volume control.
• When you adjust the channel levels while in the system setup
channel level mode, the channel level adjustments made will
affect all surround modes. Consider this mode a master
channel level adjustment mode.
• After you have completed the system setup channel level
adjustments, you can then activate the individual surround
modes and adjust channel levels that will be remembered for
each of those modes. Then, whenever you activate a particular
surround sound mode, your preferred channel level
adjustments for just that mode will be recalled. Check the
instructions for adjusting channel levels within each surround
mode (
page 29).
2 Adjusting the test tone
The volume can be adjusted between –12 dB and +12
dB in units of 0.5 dB.
4
When “Manual” mode is selected:
Press the CURSOR D or H button to select the
speaker, then press the CURSOR F or G button
to adjust all the speakers to the same volume.
5
Press the ENTER button to enter the setting.
-2
• The “Speaker Setup” menu appears.
• Before playing with the surround function, be sure to use the
test tones to adjust the playback level from the different
speakers. This adjustment can be performed with the system
setup (
page 47, 48) or from the remote control unit, as
described below.
• Adjusting with the remote control unit using the test tones is
only possible in the “Auto” mode and only effective in the
STANDARD (DOLBY/DTS SURROUND) modes. The adjusted
levels for the different modes are automatically stored in the
memory.
1
Press the STANDARD button to select the
STANDARD (DOLBY/DTS SURROUND)
modes.
2
3
Press the TEST TONE button.
4
• Test tones are output from the different speakers.
Press the CURSOR F or G button to adjust so
that the volume of the test tones is the same for
all the speakers.
After completing the adjustment, press the
TEST TONE button again.
48
ENGLISH
Set the crossover frequency mode according to the speaker
system being used.
1
Press the CURSOR D or H button to select
“Crossover Frequency” at the “Speaker Setup”
menu, then press the ENTER button.
• The “Crossover Frequency” screen appears.
2
Press the CURSOR F or G button to select the
frequency.
40 / 60 / 80 / 100 / 120 / 150 / 200 / 250 Hz can be selected.
3
Press the ENTER button to enter the setting.
• The “Speaker Setup” menu appears.
ENGLISH
Advanced Setup – Part 2
Setting the SW Mode Setup
Set the subwoofer mode according to the speaker system being
used.
1
Press the CURSOR D or H button to select “SW
Mode Setup” at the “Speaker Setup” menu, then
press the ENTER button.
• The “Subwoofer Mode Setup” screen appears.
2
3
4
Press the CURSOR F or G button to select a
setting.
Press the ENTER button to enter the setting.
• The “Speaker Setup” menu appears.
Advanced Setup – Part 2
2 Assignment of low frequency signal range
2 Subwoofer Mode
The only signals produced from the subwoofer channel are LFE
signals (during playback of Dolby Digital or DTS signals) and the
low frequency signal range of channels set to “Small” in the
setup menu. The low frequency signal range of channels set to
“Large” are produced from those channels.
• The subwoofer mode setting is only valid when “Large” is set
for the front speakers and “Yes” is set for the subwoofer in
“Setting the Speaker Config.” (
page 46).
• When the “LFE+MAIN” playback mode is selected, the low
frequency signal range of channels set to “Large” is produced
simultaneously from those channels and the subwoofer
channel.
In this playback mode, the low frequency range expands more
uniformly through the room, but depending on the size and
shape of the room, interference may result in a decrease of the
actual volume of the low frequency range.
• Selection of the “LFE” play mode will play the low frequency
signal range of the channel selected with “Large” from that
channel only. Therefore, the low frequency signal range that is
played from the subwoofer channel is only the low frequency
signal range of LFE (only during Dolby Digital or DTS signal
playback) and the channels specified as “Small” in the setup
menu.
• Select the play mode that offers the fullest bass.
• When the subwoofer is set to “Yes”, bass sound is output from
the subwoofer regardless of the subwoofer mode setting in
surround modes other than Dolby/DTS.
• In surround modes other than Dolby Digital and DTS, if the
subwoofer is set to “Yes”, the low frequency portion is always
output to the subwoofer channel. For details, refer to
“Surround modes and parameters” (
page 60).
2 Crossover Frequency
• When “Subwoofer” is set to “Yes” at the “Speaker Config.”
screen, set the frequency (Hz) below which the bass sound of
the various speakers is to be output from the subwoofer (the
crossover frequency).
• For speakers set to “Small”, sound with a frequency below
the crossover frequency is cut, and the cut bass sound is
output from the subwoofer instead.
(• When “Subwoofer” is set to “No”, the bass sound is output
from the speakers set as “Large”.)
NOTE:
• For ordinary speaker systems, we recommend setting the
crossover frequency to 80 Hz. When using small speakers,
however, setting the crossover frequency to a higher
frequency may improve frequency response for frequencies
near the crossover frequency.
Press the CURSOR D or H button to select
“Exit”, then press the ENTER button.
• The “System Setup” menu reappears.
• This screen is not displayed when not using a subwoofer and
all speakers are set to small size.
49
ENGLISH
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
Others Setup
Setting the Manual EQ Setup
Adjust the tone of the various speakers except subwoofer
speaker while listening to the sound (music).
1
4
2
Press the CURSOR D or H button to select the
frequency.
Press the CURSOR F or G button to select “All”
or “Assign”.
All:
The Equalizer to all surround mode is set as once.
Assign:
The Equalizer to each surround mode is to set individually.
Press the CURSOR D or H button to select
“Auto Setup/Room EQ” at the “System Setup”
menu, then press the ENTER button.
• The “Auto Setup/Room EQ” menu appears.
3
When “All” is selected:
Press the ENTER button.
3
When “All” is selected:
Press the CURSOR F or G button to select the
equalizer setting.
-1
5
• The “Select The EQ Curve” screen appears.
Press the CURSOR F or G button to to adjust
the gain level.
Each frequency can be adjusted the range from –6 dB to +6
dB in 0.5 dB step.
2
Press the CURSOR D or H button to select
“Manual EQ Setup”, then press the ENTER
button.
• The “Manual EQ Setup” screen appears.
6
Press the ENTER button to enter the setting.
• The “Auto Setup/Room EQ” menu appears.
-2
Setting the Room EQ Setup
Select the setting of an Equalizer that has been set with “Auto
Setup” or “Manual EQ”.
1
3
Press the CURSOR D or H button to select
“Room EQ Setup” at the “Auto Setup/Room
EQ” menu, then press the ENTER button.
• The “Room EQ Setup” screen appears.
Press the CURSOR F or G button to select the
speaker to be set.
FR
SBR
SBL
SB
SL
C
Normal:
Adjust the frequency response of all speaker suitable for
general surround system.
Flat:
Adjust the frequency response of all speakers flat.
Front:
Adjusts the characteristics of each speaker to the
characteristics of the front speakers.
Manual:
Selects the setting value that was set in the Manual EQ
setup.
The display changes as follows.
FL
OFF:
The Equalizer is not used.
SR
4
1sp
When the surround back speaker setting is set to “1sp” at
“Speaker Configuration”, this is set to “SB”.
50
ENGLISH
Press the ENTER button to enter the setting.
• The “Auto Setup/Room EQ” menu appears.
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
Check the EQ parameter
• The Equalizer setting of “Normal”, “Flat” and “Front” can be
selected after performing the Auto Setup.
• When the speaker set as “None” with the Auto Setup is
change to on manually, the equalizer of “Normal”, “Front” and
“Flat” cannot be used.
• The Equalizer setting can be selected by SURROUND
PARAMETER button.
• When headphone is connected, the Room EQ cannot be used.
• The frequency characteristic of each speaker is rectified and
the tone of the speaker is unified.
• The EQ parameters that were set in Auto Setup can be
checked.
• This item is automatically displayed, after the measurement
result of the “Auto Setup/Room EQ” is decided.
1
Setting the Direct Mode Setup
6
Press the CURSOR D or H button to select
“Direct Mode Setup” at the “Auto Setup/Room
EQ” menu, then press the ENTER button.
2
Press the CURSOR D or H button to select the
equalizer curve, then press the ENTER button.
3
4
Press the CURSOR F or G button to select the
speaker channel.
• The parameter screen appears.
Press the CURSOR F or G button to select “ON”
or “OFF”.
Press the ENTER button to enter the setting.
• The “Auto Setup/Room EQ” menu appears.
• The “Auto Setup/Room EQ” menu appears.
• The “EQ Parameter Check” screen appears.
• The “Direct Mode Setup” screen appears.
2
3
If the check ends, press the CURSOR D or H
button to select “Exit”, then press the ENTER
button.
Press the CURSOR D or H button to select “EQ
Parameter Check” at the “Auto Setup/ Room
EQ” menu, then press the ENTER button.
Perform the ON/OFF setting of Room EQ when the surround
mode is “Direct” or “Pure Direct”.
1
5
Press the ENTER button to enter the setting.
51
ENGLISH
Press the CURSOR D or H button to select
“Exit”, then press the ENTER button.
• The “System Setup” menu appears.
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
System setup items and default values (set upon shipment from the factory)
1. Auto Setup / Room EQ
Auto Setup / Room EQ
1 Auto Setup
Power Amp
Assign.
Set this to switch the surround back
channel’s power amplifier for ZONE2 or BiAmp use .
Default setting
Page
SURROUND BACK
8~11
2
Manual EQ
Setup
This parameter is for optimizing the Room EQ with which
the audio signals are produced from the speakers.
All Channel and Frequency = 0 dB
50
3
Room EQ
Setup
Set the Room EQ setting with “All” or “Assign” for each
surround mode.
All
50, 51
4
Direct Mode
Setup
Set the ON/OFF setting of Room EQ, in the case of the
surround mode is in “Direct” or “Pure Direct”.
OFF
51
2. Speaker Setup
Speaker Setup
1
Speaker
Config.
2 Delay Time
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE
for full-size, full-range) to automatically set the composition
of the signals output from the speakers and the frequency
response.
This parameter is for optimizing the timing with which the
audio signals are produced from the speakers and
subwoofer according to the listening position.
Default setting
Page
Front Sp.
Center Sp.
Subwoofer
Surround Sp.
Surround Back
Sp.
Large
Small
Yes
Small
Small / 2sp
Front
L&R
Center
Subwoofer
Surround
L&R
Surround Back
L&R
12 ft
12 ft
12 ft
10 ft
10 ft
46
Center
0 dB
0 dB
Surround
Back L
Surround
Back R
Subwoofer
0 dB
0 dB
0 dB
Channel
Level
This adjusts the volume of the signals output from the Front
L
speakers and subwoofer for the different channels in order
to obtain optimum effects.
0 dB
4
Crossover
Frequency
Sets the frequency (Hz) below which the bass sound of
the various speaker is to be output from the subwoofer.
80 Hz
48
5
SW Mode
Setup
This selects the subwoofer speaker for playing deep bass
signals.
LFE (Normal)
49
3
Front
R
47
Surround L Surround R
0 dB
0 dB
52
ENGLISH
47, 48
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
3. Input Setup
Input Setup
1
2
CD
DVD / VDP
TV / DBS
VCR-1
CDR / TAPE
Digital
Inputs
COAX1
OPT1
OPT2
COAX2
OPT3
Digital In
Assign.
This assigns the digital input terminals for the
different input sources.
Ext In SW
Level
Sets the Ext. In Subwoofer terminal playback level.
41
Subwoofer = +15 dB
Input
3 Function
Level
The playback level can be corrected individually for the PHONO
different input sources.
0 dB
4
Function
Rename
The names of the different input source can be changed as
PHONO
desired and displayed on the display.
5
Component
In Assign.
This assigns the color difference (component) video input
terminals for the different input sources.
6
Video Input
Mode
Set the input signal to be output from the monitor output
terminal.
7
Auto Tuner
Preset
Page
Default setting
Input
source
FM stations are received automatically and stored in the
memory.
41
CD
TUNER
CDR /
TAPE
DVD /
TV / DBS VCR-1
VDP
VCR-2
V. AUX
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
CD
TUNER
CDR
DVD
TV
VCR-1
VCR-2
V. AUX
DVD / VDP
TV / DBS
VCR-1
VCR-2
V. AUX
VIDEO1
VIDEO2
VIDEO3
OFF
OFF
AUTO
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 / 90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
41
42
42
43
43
4. Advanced Playback
Advanced Playback
Default setting
Page
0 ms
44
1 Audio Delay
Sets the audio delay to delay the sound and synchronize it
with the picture.
Auto
2 Surround
Mode
Sets the Auto surround mode function.
Auto Surround Mode = ON
44
Option Setup
5. Option Setup
Default setting
Page
1 Muting Level
This sets the amount of attenuation for audio output
muting.
– – – dB (minimum)
45
2
On Screen
Display
This sets whether or not to display the on screen display
that appears on the monitor screen when the controls on
the remote control unit or main unit are operated.
A setting to prevent flickering.
On Screen Display = ON / MODE1
45
3
Power Amp
Assign.
Set this to switch the surround back channel’s power
amplifier for ZONE2 or Bi-Amp use.
Surround Back
45
4 Setup Lock
Sets whether or not to lock the system setup settings so
that they cannot be changed.
Setup Lock = OFF
46
53
ENGLISH
ENGLISH
Troubleshooting
Symptom
Cause
This unit does not
operate properly when
remote control unit is
used.
• Batteries dead.
• Remote control unit too far from
this unit.
• Obstacle between this unit and
remote control unit.
• Different button is being pressed.
• < and > ends of batteries inserted
in reverse.
Troubleshooting
If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properly?
If this unit is not operating properly, check the items listed in the table below. Should the problem
persist, there may be a malfunction. Disconnect the power immediately and contact your store of
purchase.
Symptom
Display not lit and
sound not produced
when POWER switch
set to on.
Display lit but sound
not produced.
Cause
Measures
• Power supply cord not plugged in • Check the insertion of the power
securely.
supply cord plug.
• Turn the power on with the remote
control unit after turning the
POWER switch on.
• Speaker cables not securely
connected.
• Improper setting of the FUNCTION
knob.
• Volume control set to minimum.
• MUTING is on.
• Digital signals not input. Digital
input selected.
Page
18
8
• Connect securely.
6
• Set to a suitable position.
19
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input
terminals to which digital signals
are being input.
5, 6
• Incomplete connection of speaker • Connect securely.
cables.
• Incomplete connection of input/ • Connect securely.
output cables.
5, 6
Sound produced only
from one channel.
Positions of
instruments reversed
during stereo playback.
• Reverse connections of left and • Check left and right connections.
right speakers or left and right
input/output cables.
6
Howling noise
produced when
volume is high.
• Speaker systems too close • Separate as much as possible.
together.
• Floor is unstable and vibrates • Use cushions to absorb speaker
easily.
vibrations transmitted by floor.
—
Sound is distorted.
• Stylus pressure too weak.
• Dust or dirt on stylus.
—
—
Display not lit and
power indicator is
flashing rapidly.
are
• Apply proper stylus pressure.
• Check stylus.
Page
• Replace with new batteries.
• Move closer.
3
3
• Remove obstacle.
3
• Press the proper button.
• Insert batteries properly.
—
3
“CHECK ANTENNA” is • AVR-886’s XM terminal and the • Check that the connection are
XM Connect-and-Play antenna is
correct.
displayed.
not properly connected.
16
“NO SIGNAL” is
displayed.
• The signal cannot be received.
32
“OFF AIR” is
displayed.
• The selected channel is not • Select the another channel.
currently broadcasting.
32
Receiving only XM
channels 0 and 1.
• The XM Tuner is not activated.
32
• Reposition your XM Connect-andPlay antenna.
• Contact XM Radio.
2 NOTE ON USE
19
19
20, 21
short- • Switch power off, connect
speakers properly, then switch
power back on.
• The ventilation holes of the set are • Turn off the set’s power, then
ventilate it well and allow it to cool
blocked.
down.
Once the set has cooled down,
turn the power back on.
• The unit is operating at continuous • Turn off the set’s power, then
ventilate it well and allow it to cool
high power conditions and/or with
down.
inadequate ventilation.
Once the set has cooled down,
turn the power back on.
• Speaker terminals
circuited.
Measures
2, 5
Keep the apparatus free from
moisture, water, and dust.
Do not let foreign objects into the
apparatus.
Avoid high temperatures.
Allow for sufficient heat dispersion
when installed in a rack.
2, 5
Unplug the power cord when not
using the apparatus for long
periods of time.
5~7,
11~18
Handle the power cord carefully.
Hold the plug when unplugging the
cord.
—
* (For apparatuses with ventilation holes)
Do not obstruct the ventilation holes.
54
ENGLISH
Do not let insecticides, benzene,
and thinner come in contact with
the apparatus.
Never disassemble or modify the
apparatus in any way.
ENGLISH
Additional Information
Surround back speakers
Additional Information
• Other types of audio:
These signals are designed to recreate a 360° sound field using
three to five speakers.
Optimum surround sound for different
sources
There are currently various types of multi-channel signals (signals
or formats with more than two channels).
FL
SW
C
FR
2 Types of multi-channel signals
Dolby Digital, Dolby Pro Logic, DTS, high definition 3-1 signals
(Japan MUSE Hi-Vision audio), DVD-Audio, Super Audio CD,
MPEG multi-channel audio, etc.
A 6.1-channel system is a conventional 5.1-channel system to
which the “surround back” (SB) channel has been added. This
makes it easy to achieve sound positioned directly behind the
listener, something that was previously difficult with sources
designed for conventional multi surround speakers. In addition,
the acoustic image extending between the sides and the rear is
narrowed, thus greatly improving the expression of the surround
signals for sounds moving from the sides to the back and from
the front to the point directly behind the listening position.
Change of positioning and acoustic image
with 5.1-channel systems
FL
“Source” here does not refer to the type of signal (format) but
the recorded content. Sources can be divided into two major
categories.
2 Types of sources
• Movie audio:
Signals created to be played in movie theaters. In general
sound is recorded to be played in movie theaters equipped with
multiple surround speakers, regardless of the format (Dolby
Digital, DTS, etc.).
Movie theater sound field
FL
SW
C
SL
SL
SR
FL
SW
C
FR
In this case the speakers should surround the listener from all
sides to create a uniform sound field from 360°. Ideally the
surround speakers should function as “point” sound sources in
the same way as the front speakers.
These two types of sources thus have different properties, and
different speaker settings, particularly for the surround speakers,
are required in order to achieve the ideal sound.
SL ch
SR ch
Movement of acoustic image from SR to SL
Change of positioning and acoustic image
with 6.1-channel systems
FR
FL
SL
C
SR
Listening room
sound field
FR
SW
SW
C
FR
SR
SB
SL ch
SR ch
SB
Multiple surround speakers
(For 6.1-channel system)
SB ch
In this case it is important to achieve the same sense of
expansion as in a movie theater with the surround channels.
To do so, in some cases the number of surround speakers is
increased (to four or eight) or speakers with bipolar or dipolar
properties are used.
 SL : Surround L channel
 SR : Surround R channel

 SB : Surround back channel (1 speaker or 2 speakers)
Movement of acoustic image from SR to SB to SL
55
ENGLISH
ENGLISH
Additional Information
With this set, speaker(s) for 1 or 2 channels are required to
achieve a 6.1-channel system (DTS-ES, etc.). Adding these
speakers, however, increases the surround effect not only with
sources recorded in 6.1 channels but also with conventional 2- to
5.1-channel sources. Furthermore, all the DENON original
surround modes (
page 26) are compatible with 7.1-channel
playback, so you can enjoy 7.1-channel sound with any signal
source.
2 Number of surround back speakers
Though the surround back channel only consists of 1 channel of
playback signals for 6.1-channel sources (DTS-ES, etc.), we
recommend using two speakers. When using speakers with
dipolar characteristics in particular, it is essential to use two
speakers.
Using two speakers results in a smoother blend with the sound
of the surround channels and better sound positioning of the
surround back channel when listening from a position other than
the center.
Additional Information
60°
Path of the surround sound from the
speakers to the listening position
Surround
speakers
60°
Surround back speakers
[ As seen from above ]
Using surround back speakers greatly improves the positioning
of the sound at the rear. Because of this, the surround left and
right channels play an important role in achieving a smooth
transition of the acoustic image from the front to the back. As
shown in the diagram above, in a movie theater the surround
signals are also produced from diagonally in front of the listeners,
creating an acoustic image as if the sound were floating in space.
To achieve these effects, we recommend placing the speakers
for the surround left and right channels slightly more towards the
front than with conventional surround systems. Doing so
sometimes increases the surround effect when playing
conventional 5.1-channel sources in the 6.1 surround or DTS-ES
Matrix 6.1 mode. Check the surround effects of the various
modes before selecting the surround mode.
Front speaker
[1] DTS-ES compatible system
(using surround back speakers)
q Basic setting for primarily watching movies
For the greatest sense of surround sound envelopment, diffuse
radiation speakers such as bipolar types, or dipolar types, provide
a wider dispersion than is possible to obtain from a direct
radiating speaker (monopolar). Place these speakers at either
side of the prime listening position, mounted above ear level.
Subwoofer
Surround speaker
Here we describe a number of speaker settings for different
purposes. Use these examples as guides to set up your system
according to the type of speakers used and the main usage
purpose.
diffusion type speakers for the surround
speakers
Monitor
2 Placement of the surround left and right
channels when using surround back speakers
Speaker setting examples
w Setting for primarily watching movies using
Front speakers
Center speaker
Surround
speakers
Surround back
speaker
Point slightly
downwards
2 to 3 feet
60°
Surround back speakers
[ As seen from above ]
[ As seen from the side ]
• Set the front speakers with their front surfaces as flush with
the TV or monitor screen as possible. Set the center speaker
between the front left and right speakers and no further from
the listening position than the front speakers.
• Consult the owner’s manual for your subwoofer for advice on
placing the subwoofer within the listening room.
• If the surround speakers are direct-radiating (monopolar), then
place them slightly behind and at an angle to the listening
position and parallel to the walls at a position 2 to 3 feet above
ear level at the prime listening position.
• When using two surround back speakers, place them at the
back facing the front at a narrower distance than the front left
and right speakers. When using one surround back speaker,
place it at the rear center facing the front at a slightly higher
position 0 to 0.7 feet than the surround speakers.
• We recommend installing the surround back speaker(s) at a
slightly downward facing angle. This effectively prevents the
surround back channel signals from reflecting off the monitor or
screen at the front center, resulting in interference and making
the sense of movement from the front to the back less sharp.
This is recommended when mainly playing movies and using
regular single way or 2-way speakers for the surround speakers.
56
ENGLISH
Surround speaker
Surround back
speaker
Front speaker
Point slightly
downwards
2 to 3 feet
[ As seen from the side ]
• Set the front speakers, center speaker and subwoofer in the
same positions as in example (1).
• It is best to place the surround speakers directly at the side or
slightly to the front of the viewing position, and 2 to 3 feet
above the ears.
• Same as surround back speaker installation method (1). Using
dipolar speakers for the surround back speakers as well is more
effective.
• The signals from the surround channels reflect off the walls as
shown in the diagram above, creating an enveloping and
realistic surround sound presentation.
ENGLISH
Additional Information
Additional Information
[2] When not using surround back speakers
Front speakers
Center speaker
Monitor
Subwoofer
60°
120°
Surround speakers
[ As seen from above ]
Surround speaker
Surround
The AVR-886 is equipped with a digital signal processing circuit
that lets you play program sources in the surround mode to
achieve the same sense of presence as in a movie theater.
q Dolby Digital
Dolby Digital is the multi-channel digital signal format developed
by Dolby Laboratories.
Dolby Digital consists of up to “5.1” channels – front left, front
right, center, surround left, surround right, and an additional
channel exclusively reserved for additional deep bass sound
effects (the Low Frequency Effects –LFE– channel, also called
the “.1” channel, containing bass frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital’s main
channels can all contain full range sound information, from the
lowest bass, up to the highest frequencies – 22 kHz. The signals
within each channel are distinct from the others, allowing
pinpoint sound imaging, and Dolby Digital offers tremendous
dynamic range from the most powerful sound effects to the
quietest, softest sounds, free from noise and distortion.
2 to 3 feet
[ As seen from the side ]
• Set the front speakers with their front surfaces as flush with
the TV or monitor screen as possible. Set the center speaker
between the front left and right speakers and no further from
the listening position than the front speakers.
• Consult the owner’s manual for your subwoofer for advice on
placing the subwoofer within the listening room.
• If the surround speakers are direct-radiating (monopolar), then
place them slightly behind and at an angle to the listening
position and parallel to the walls at a position 2 to 3 feet above
ear level at the prime listening position.
Symbol indicating Dolby Digital compatibility:
The following are general examples. Also refer to the player’s
operating instructions.
[1] Dolby Surround
2 Dolby Digital and Dolby Pro Logic
Front speaker
2 Dolby Digital compatible media and playback
methods
Comparison of home
surround systems
Dolby Digital
Dolby Pro Logic
No. of recorded
channels (elements)
5.1 ch
2 ch
No. of playback
channels
5.1 ch
4 ch
Playback channels
(max.)
L, R, C, SL, SR, SW
L, R, C, S
(SW – recommended)
Audio processing
Digital discrete
processing Dolby
Digital encoding /
decoding
Analog matrix
processing Dolby
Surround
High frequency
playback limit of
surround channel
20 kHz
7 kHz
57
ENGLISH
Media
Dolby Digital output
terminals
Playback method
(reference page)
LD (VDP)
Coaxial Dolby Digital
RF output terminal
1
Set the input mode to
“AUTO”
(
page 20, 21).
DVD
Optical or coaxial
digital output
(same as for PCM)
2
Set the input mode to
“AUTO”
(
page 20, 21).
Others
(satellite broadcasts,
CATV, etc.)
Optical or coaxial
digital output
(same as for PCM)
Set the input mode to
“AUTO”
(
page 20, 21).
1: Please use a commercially available adapter when
connecting the Dolby Digital RF output terminal of the LD
player to the digital input terminal.
Please refer to the instruction manual of the adapter when
making connection.
2: Some DVD digital outputs have the function of switching
the Dolby Digital signal output method between “bit
stream” and “(convert to) PCM”. When playing in Dolby
Digital surround on the AVR-886, switch the DVD player’s
output mode to “bit stream”. In some cases players are
equipped with both “bit stream + PCM” and “PCM only”
digital outputs. In this case connect the “bit stream +
PCM” terminals to the AVR-886.
w Dolby Pro Logic II
• Dolby Pro Logic II is a new multi-channel playback format
developed by Dolby Laboratories using feedback logic steering
technology and offering improvements over conventional Dolby
Pro Logic circuits.
• Dolby Pro Logic II can be used to decode not only sources
recorded in Dolby Surround ( ) but also regular stereo sources
into five channels (front left, front right, center, surround left
and surround right) to achieve surround sound.
ENGLISH
Additional Information
• Whereas with conventional Dolby Pro Logic the surround
channel playback frequency band was limited, Dolby Pro Logic
II offers a wider band range (20 Hz to 20 kHz or greater). In
addition, the surround channels were monaural (the surround
left and right channels were the same) with previous Dolby Pro
Logic, but with Dolby Pro Logic II they are played as stereo
signals.
• Various parameters can be set according to the type of source
and the contents, so it is possible to achieve optimum decoding
(
page 60).
e Dolby Pro Logic IIx
Dolby Pro Logic IIx furthers the matrix decoding technology of
Dolby Pro Logic II to decode audio signals recorded on two
channels into up to 7.1 playback channels, including the surround
back channel. Dolby Pro Logic IIx also allows 5.1-channel
sources to be played in up to 7.1 channels.
The mode can be selected according to the source. The Music
mode is best suited for playing music, the Cinema mode for
playing movies, and the Game mode for playing games. The
Game mode can only be used with 2-channel audio sources.
Sources recorded in Dolby Surround
• These are sources in which three or more channels of surround
have been recorded as two channels of signals using Dolby
Surround encoding technology.
• Dolby Surround is used for the sound tracks of movies recorded
on DVDs, LDs and video cassette tapes, as well as for stereo
broadcast signals from FM radio, TV, satellite broadcasts and
cable TV.
• Decoding these signals with Dolby Pro Logic II makes it
possible to achieve multi-channel surround playback. The
signals can also be played on ordinary stereo equipment, in
which case they provide normal stereo sound.
• There are two types of DVD Dolby surround recording signals.
q 2-channel PCM stereo signals
w 2-channel Dolby Digital signals
• When either of these signals is input to the AVR-886, the
surround mode is automatically set to Dolby Pro Logic II when
the DOLBY/DTS SURROUND mode is selected.
2 Sources recorded in Dolby Surround are
indicated with the logo symbol shown below
Additional Information
[2] DTS Digital Surround
Digital Theater Surround (also called simply DTS) is a multichannel digital signal format developed by Digital Theater
Systems.
DTS offers the same “5.1” playback channels as Dolby Digital
(front left, front right, center, surround left and surround right) as
well as the stereo 2-channel mode. The signals for the different
channels are fully independent, eliminating the risk of
deterioration of sound quality due to interference between
signals, crosstalk, etc.
DTS features a relatively higher bit rate as compared to Dolby
Digital (1234 kbps for CDs and LDs, 1536 kbps for DVDs) so it
operates with a relatively low compression rate. Because of this
the amount of data is great, and when DTS playback is used in
movie theaters, a separate CD-ROM synchronized with the film
is played.
With LDs and DVDs, there is of course no need for an extra disc;
the pictures and sound can be recorded simultaneously on the
same disc, so the discs can be handled in the same way as discs
with other formats.
There are also music CDs recorded in DTS. These CDs include
5.1-channel surround signals (compared to two channels on
current CDs). They do not include picture data, but they offer
surround playback on CD players that are equipped with digital
outputs (PCM type digital output required).
DTS surround track playback offers the same intricate, grand
sound as in a movie theater, right in your own listening room.
2 DTS compatible media and playback methods
Symbols indicating DTS compatibility:
and
The following are general examples. Also refer to the player’s
operating instructions.
MANUFACTURED UNDER LICENSE FROM DIGITAL
THEATER SYSTEMS, INC.
U.S. PAT. NO’S. 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535 AND OTHER U.S. AND WORLDWIDE
PATENTS ISSUED AND PENDING.
“DTS”, “DTS–ES”, “Neo:6”, AND “DTS 96/24” ARE
TRADEMARKS OF DIGITAL THEATER SYSTEMS, INC. ©
1996, 2003 DIGITAL THEATER SYSTEMS, INC. ALL RIGHTS
RESERVED.
Dolby Surround logo symbol:
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
58
ENGLISH
Media
Dolby Digital output
terminals
Playback method
(reference page)
CD
Optical or coaxial digital
output
(same as for PCM)
2
Set the input mode to
“AUTO” or “DTS”
(
page 20, 21).
Never set the mode to
“ANALOG” or “PCM”.
1
LD (VDP)
Optical or coaxial digital
output
(same as for PCM)
2
Set the input mode to
“AUTO” or “DTS”
(
page 20, 21).
Never set the mode to
“ANALOG” or “PCM”.
1
DVD
Optical or coaxial digital
output
(same as for PCM)
3
Set the input mode to
“AUTO” or “DTS”
(
page 20, 21).
1: DTS signals are recorded in the same way on CDs and LDs
as PCM signals. Because of this, the un-decoded DTS
signals are output as random “hissing” noise from the CD
or LD player’s analog outputs. If this noise is played with
the amplifier set at a very high volume, it may possibly
cause damage to the speakers. To avoid this, be sure to
switch the input mode to “AUTO” or “DTS” before playing
CDs or LDs recorded in DTS. Also, never switch the input
mode to “ANALOG” or “PCM” during playback. The same
holds true when playing CDs or LDs on a DVD player or
LD/DVD compatible player. For DVDs, the DTS signals are
recorded in a special way so this problem does not occur.
2: The signals provided at the digital outputs of a CD or LD
player may undergo some sort of internal signal processing
(output level adjustment, sampling frequency conversion,
etc.). In this case the DTS-encoded signals may be
processed erroneously, in which case they cannot be
decoded by the AVR-886, or may only produce noise.
Before playing DTS signals for the first time, turn down the
master volume to a low level, start playing the DTS disc,
then check whether the DTS indicator on the AVR-886
(
page 24) lights before turning up the master volume.
3: A DVD player with DTS-compatible digital output is required
to play DTS DVDs. A DTS Digital Output logo is featured on
the front panel of compatible DVD players. Recent DENON
DVD player models feature DTS-compatible digital output –
consult the player’s owner’s manual for information on
configuring the digital output for DTS playback of DTSencoded DVDs.
ENGLISH
Additional Information
[3] DTS-ES Extended Surround™
DTS-ES Extended Surround is a new multi-channel digital signal
format developed by Digital Theater Systems Inc. While offering
high compatibility with the conventional DTS Digital Surround
format, DTS-ES Extended Surround greatly improves the 360degree surround impression and space expression thanks to
further expanded surround signals. This format has been used
professionally in movie theaters since 1999.
In addition to the 5.1 surround channels (FL, FR, C, SL, SR and
LFE), DTS-ES Extended Surround also offers the SB (Surround
Back, sometimes also referred to as “surround center”) channel
for surround playback with a total of 6.1 channels. DTS-ES
Extended Surround includes two signal formats with different
surround signal recording methods, as described below.
2 DTS-ES™ Discrete 6.1
DTS-ES Discrete 6.1 is the newest recording format. With it, all
6.1 channels (including the SB channel) are recorded
independently using a digital discrete system. The main feature
of this format is that because the SL, SR and SB channels are
fully independent, the sound can be designed with total freedom
and it is possible to achieve a sense that the acoustic images are
moving about freely among the background sounds surrounding
the listener from 360 degrees.
Though maximum performance is achieved when sound tracks
recorded with this system are played using a DTS-ES decoder,
when played with a conventional DTS decoder the SB channel
signals are automatically down-mixed to the SL and SR channels,
so none of the signal components are lost.
2 DTS-ES™ Matrix 6.1
With this format, the additional SB channel signals undergo
matrix encoding and are input to the SL and SR channels
beforehand. Upon playback they are decoded to the SL, SR and
SB channels. The performance of the encoder used at the time
of recording can be fully matched using a high precision digital
matrix decoder developed by DTS, thereby achieving surround
sound more faithful to the producer’s sound design aims than
with conventional 5.1- or 6.1-channel systems.
In addition, the bit stream format is 100% compatible with
conventional DTS signals, so the effect of the Matrix 6.1 format
can be achieved even with 5.1-channel signal sources. Of course
it is also possible to play DTS-ES Matrix 6.1 encoded sources
with a DTS 5.1-channel decoder.
Additional Information
When DTS-ES Discrete 6.1 or Matrix 6.1 encoded sources are
decoded with a DTS-ES decoder, the format is automatically
detected upon decoding and the optimum playing mode is
selected. However, some Matrix 6.1 sources may be detected
as having a 5.1-channel format, so the DTS-ES Matrix 6.1 mode
must be set manually to play these sources. (For instructions on
selecting the surround mode (
page 24).)
The DTS-ES decoder includes another function, the DTS Neo:6
surround mode for 6.1-channel playback of digital PCM and
analog signal sources.
2 DTS Neo:6™ surround
This mode applies conventional 2-channel signals to the high
precision digital matrix decoder used for DTS-ES Matrix 6.1 to
achieve 6.1-channel surround playback. High precision input
signal detection and matrix processing enable full band
reproduction (frequency response of 20 Hz to 20 kHz or greater)
for all 6.1 channels, and separation between the different
channels is improved to the same level as that of a digital
discrete system.
DTS Neo:6 surround includes two modes for selecting the
optimum decoding for the signal source.
• DTS Neo:6 Cinema
This mode is optimum for playing movies. Decoding is
performed with emphasis on separation performance to
achieve the same atmosphere with 2-channel sources as with
6.1-channel sources.
This mode is effective for playing sources recorded in
conventional surround formats as well, because the in-phase
component is assigned mainly to the center channel (C) and the
reversed phase component to the surround (SL, SR and SB)
channels.
• DTS Neo:6 Music
This mode is suited mainly for playing music. Changes in the
sound quality are reduced by decoding with emphasis on the
front channel signals (FL and FR), and a natural sense of
expansion is given to the sound field by the effect of the
surround signals output from the center (C) and surround (SL,
SR and SB) channels.
59
ENGLISH
[4] DTS 96/24
The sampling frequency, number of bits and number of channels
used for recording of music, etc., in studios have been increasing
in recent years, and there are a growing number of high quality
signal sources, including 96 kHz/24-bit 5.1-channel sources.
For example, there are high picture/sound quality DVD video
sources with 96 kHz/24-bit stereo PCM audio tracks.
However, because the data rate for these audio tracks is
extremely high, there are limits to recording them on two
channels only, and since the quality of the pictures must be
restricted it is common to only include still pictures.
In addition, 96 kHz/24-bit 5.1-channel surround is possible with
DVD audio sources, but DVD audio players are required to play
them with this high quality.
DTS 96/24 is a multi-channel digital signal format developed by
Digital Theater Systems Inc. in order to deal with this situation.
Conventional surround formats used sampling frequencies of 48
or 44.1 kHz, so 20 kHz was about the maximum playback signal
frequency. With DTS 96/24, the sampling frequency is increased
to 96 or 88.2 kHz to achieve a wide frequency range of over 40
kHz.
In addition, DTS 96/24 has a resolution of 24-bits, resulting in the
same frequency band and dynamic range as 96 kHz/24-bit PCM.
As with conventional DTS Surround, DTS 96/24 is compatible
with a maximum of 5.1 channels, so sources recorded using DTS
96/24 can be played in high sampling frequency, multiple channel
audio with such normal media as DVD videos and CDs.
Thus, with DTS 96/24, the same 96 kHz/24-bit multi-channel
surround sound as with DVD-Audio can be achieved while
viewing DVD-Video images on a conventional DVD-Video player
( 1). Furthermore, with DTS 96/24 compatible CDs, 88.2
kHz/24-bit multi-channel surround can be achieved using normal
CD/LD players ( 1).
Even with the high quality multi-channel signals, the recording
time is the same as with conventional DTS surround sources.
What’s more, DTS 96/24 is fully compatible with the conventional
DTS surround format, so DTS 96/24 signal sources can be played
with a sampling frequency of 48 kHz or 44.1 kHz on conventional
DTS or DTS-ES surround decoders ( 2).
1 A DVD player with DTS digital output capabilities (for CD/LD
players, a player with digital outputs for conventional DTS
CDs/LDs) and a disc recorded in DTS 96/24 are required.
2 The resolution is 24 or 20 bits, depending on the decoder.
ENGLISH
Additional Information
Additional Information
Surround modes and parameters
Signals and adjustability in the different modes
When playing Dolby Digital and
DTS signals
Channel output
Mode
FRONT L/R
CENTER
SURROUND L/R
SURROUND
BACK L/R
SUBWOOFER
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
B
B
B
B
B
B
B
B
B
B
B
B
E
E
E
B
B
B
B
B
B
B
B
B
B
B
B
E
E
E
E
B
B
B
B
B
B
B
B
B
B
B
E
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
DIRECT/PURE DIRECT
STEREO
EXTERNAL INPUT
DOLBY PRO LOGIC II
DOLBY PRO LOGIC IIx
DTS NEO:6
DOLBY DIGITAL
DTS SURROUND
5CH/7CH STEREO
ROCK ARENA
JAZZ CLUB
VIDEO GAME
MONO MOVIE
MATRIX
VIRTUAL
When playing
DTS signals
C
C
E
C*
C*
C*
C
E
C
C
C
C
C
C
C
C : Signal / Adjustable
E : No signal
B : Turned on or off by speaker configuration setting
C
C
E
C*
C*
C*
E
C
C
C
C
C
C
C
C
When playing
PCM signals
When playing
ANALOG signals
D. COMP.
LFE
C
C
E
C
C
C
E
E
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
C
C
C
C
C
C
C
C (OFF)
C (OFF)
E
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (0 dB)
C (0 dB)
E
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C : Able
E : Unable
* : Only for 2 ch contents
C : Able
E : Unable
Signals and adjustability in the different modes
Surround parameter
PRO LOGIC II / IIx only
Mode
DIRECT/PURE DIRECT
STEREO
EXTERNAL INPUT
DOLBY PRO LOGIC II
DOLBY PRO LOGIC IIx
DTS NEO:6
DOLBY DIGITAL
DTS SURROUND
5CH/7CH STEREO
ROCK ARENA
JAZZ CLUB
VIDEO GAME
MONO MOVIE
MATRIX
VIRTUAL
When playing
Dolby Digital
signals
SB CH OUT
(MODE)
TONE
CONTROL
CINEMA
EQ.
MODE
ROOM SIZE
EFFECT
LEVEL
Room EQ
DELAY TIME
E
E
E
C
C
C
C
C
C
C
C
C
C
C
E
E
C (0 dB)
E
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
C (0 dB)
E
E
E
E
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
E
E
E
E
E
E
E
E
E
E
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C (Medium)
C (Medium)
C (Medium)
C (Medium)
E
E
E
E
E
E
E
E
E
E
E
C (10)
C (10)
C (10)
C (10)
E
E
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
C (OFF)
E
E
E
E
E
E
E
E
E
E
E
E
E
C (30 msec)
E
C : Adjustable
E : Not adjustable
60
ENGLISH
SUBWOOFER PANORAMA DIMENSION
ON/OFF
C (OFF)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C (OFF)
C (OFF)
E
E
E
E
E
E
E
E
E
E
E
E
E
C (3)
C (3)
E
E
E
E
E
E
E
E
E
E
NEO:6 MUSIC
EXT. IN
CENTER
WIDTH
CENTER
IMAGE
SW ATT
E
E
E
C (3)
C (3)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C (0.3)
E
E
E
E
E
E
E
E
E
E
E
C
E
E
E
E
E
E
E
E
E
E
E
E
ENGLISH
Specifications
2 Video section
Specifications
• Standard video terminals
Input / output level
and impedance:
1 Vp-p, 75 Ω/ohms
Frequency response:
5 Hz ~ 10 MHz — +1, –3 dB
• S-Video terminals
Input / output level
and impedance:
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
Frequency response:
5 Hz ~ 10 MHz — +1, –3 dB
• Color component video terminal
Input / output level
and impedance:
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB/CB (blue) signal — 0.7 Vp-p, 75 Ω/ohms
PR/CR (red) signal — 0.7 Vp-p, 75 Ω/ohms
Frequency response:
DC ~ 100 MHz — +0, –3 dB
2 Audio section
• Power amplifier
Rated output:
Dynamic power:
Output terminals:
• Analog
Input sensitivity /
input impedance:
Frequency response:
S/N:
Distortion:
Rated output:
• Phono equalizer (PHONO
Input sensitivity:
RIAA deviation:
S/N:
Rated output /
Maximum output:
Distortion factor:
Front:
100 W + 100 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08%
135 W + 135 W
(6 Ω/ohms, 1 kHz with 0.7% T.H.D.)
Center:
100 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08%
135 W
(6 Ω/ohms, 1 kHz with 0.7% T.H.D.)
Surround:
100 W + 100 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08%
135 W + 135 W
(6 Ω/ohms, 1 kHz with 0.7% T.H.D.)
Surround Back: 100 W + 100 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08%
135 W + 135 W
(6 Ω/ohms, 1 kHz with 0.7% T.H.D.)
120 W x 2 ch (8 Ω/ohms)
170 W x 2 ch (4 Ω/ohms)
200 W x 2 ch (2 Ω/ohms)
Front:
A or B
16 ~ 16 Ω/ohms
A+B
12 ~ 16 Ω/ohms
Center, Surround, Surr.Back: 16 ~ 16 Ω/ohms
T.H.D.)
T.H.D.)
T.H.D.)
2 Tuner section
T.H.D.)
Receiving Range:
Usable Sensitivity:
50 dB Quieting
Sensitivity:
S/N (IHF-A):
[FM] (note: µV at 75 Ω/ohms,
0 dBf=1 x 10–15 W)
87.50 MHz ~ 107.90 MHz
1.0 µV (11.2 dBf)
MONO
STEREO
MONO
STEREO
Total Harmonic Distortion
(at 1 kHz):
MONO
STEREO
200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz: +1, –3 dB (DIRECT mode)
100 dB (IHF-A weighted) (DIRECT mode)
0.008% (20 Hz ~ 20 kHz) (DIRECT mode)
1.2 V
input — REC OUT)
2.5 mV
±1 dB (20 Hz to 20 kHz)
74 dB (A weighting, with 5 mV input)
[AM]
520 kHz ~ 1710 kHz
18 µV
1.6 µV (15.3 dBf)
23 µV (38.5 dBf)
77 dB (IHF-A weighted)
72 dB (IHF-A weighted)
0.15 % (1 kHz)
0.3 % (1 kHz)
2 General
Power supply:
Power consumption:
Maximum external
dimensions:
Mass:
150 mV / 7 V
0.03 % (1 kHz, 3 V)
AC 120 V, 60 Hz
5.5 A
1 W max. (Standby)
434 (W) x 171 (H) x 417 (D) mm
(17-3/32” x 6-47/64” x 16-27/64”)
13.0 kg (28 lbs 11 oz)
2 Remote control unit (RC-1004)
Batteries:
External dimensions:
Mass:
R6P/AA Type (two batteries)
55 (W) x 225 (H) x 34.5 (D) mm
(2-11/64” x 8-55/64” x 1-9/64”)
165 g (Approx. 5.8 oz) (including batteries)
* For purposes of improvement, specifications and design are subject to change without notice.
61
ENGLISH
FRANCAIS
ENGLISH
2 List of preset codes / Liste de codes préréglés
DVD
Audio Dynamic
005, 085
Denon
014, *[111]
Audiovox
088
Aiwa
009
Beaumark
087
Jensen
Hitachi
010
Broksonic
086, 093
JVC
JVC
006, 011
Calix
088
Konka
012, 013
Candle
006, 087, 088, 089, 090
Magnavox
005
Canon
049, 057
Mitsubishi
004
Capehart
025, 055, 056, 071
Kodak
088
Panasonic
014
Carver
015
Lloyd
009, 094
Philips
005, 015, 016, 017
CCE
095
LXI
088
Pioneer
003, 008
Citizen
006, 007, 087, 088, 089, 090, 095
Magnavox
015, 016, 042, 049, 063, 106
Sanyo
018
Craig
007, 087, 088, 091, 115
Magnin
087
Sony
002, 019, 020
Curtis Mathes
006, 049, 073, 080, 087, 090, 092
Marantz
004, 005, 006, 015, 042, 049, 085, 090
Toshiba
001, 021, 022
Cybernex
087
Marta
088
Zenith
023
Daewoo
025, 055, 059, 074, 089, 093, 095, 096
MEI
049
Daytron
025, 055
Memorex
009, 033, 049, 053, 060, 081, 087, 088,
VDP
JC Penny
004, 005, 007, 023, 028, 049, 062, 085,
087, 088
013, 026
004, 005, 006, 026, 029, 043, 044, 045,
046, 085
Kenwood
004, 005, 006, 026, 029, 033, 045, 085,
090
091, 094, 115
DBX
005, 085
Denon
028, 029, 112
Dumont
053
Metz
Magnavox
026
Dynatech
009
MGA
001, 017, 027, 041, 097
Mitsubishi
028
Electrohome
001, 088, 097
MGN Technology
087
Panasonic
029, 030
Electrophonic
088
Midland
011
Philips
026
Emerson
001, 009, 017, 027, 086, 088, 089, 092,
Minolta
013, 023
Pioneer
028, 031
093, 097, 100, 101, 102, 103, 104, 117
Mitsubishi
RCA
032
Fisher
Sony
033, 034, 035, 036
GE
VCR
123, 124, 125, 126, 127, 128
001, 003, 008, 013, 014, 017, 027, 029,
039, 040, 041, 045, 097
009, 028, 031, 053, 054, 091, 099, 115
007, 011, 049, 050, 051, 052, 073, 080,
Motorola
081
087
Montgomery Ward
001, 002, 007, 009, 049, 063, 081, 115,
Go Video
047, 048
117
Admiral
081
Goldstar
000, 006, 012, 062, 088
MTC
009, 087, 094
Aiko
095
Gradiente
094
Multitech
007, 009, 011, 087, 090, 094
Aiwa
009
Grundig
042
NAD
038
Akai
026, 027, 070, 072, 082, 083, 084
Harley Davidson
094
NEC
004, 005, 006, 018, 026, 029, 045, 061,
Alba
055
Harman Kardon
040, 062
Amstrad
009
Hi-Q
091
Nikko
088
ASA
042
Hitachi
009, 013, 023, 026, 058, *[108], 109,
Noblex
087
110, 111
Optimus
081, 088
Asha
087
062, 085
ENGLISH
FRANCAIS
Optonica
021
Sylvania
009, 015, 016, 017, 041, 049, 094
Bauer
155
Panasonic
024, 049, 064, 066, 067, 068, 069, 107
Symphonic
009, 094
Belcor
047
Perdio
009
Tandy
009
Bell & Howell
045, 118
Pentax
009, 013, 023, 058, 090
Tashiko
009, 088
Bradford
061
Philco
015, 016, 049
Tatung
004, 026, 030
Brockwood
003, 047
Philips
015, 021, 042, 049, 105
Teac
004, 009, 026, 094
Candle
Pilot
088
Technics
024, 049
Pioneer
005, 013, 029, 036, 037, 038, 045, 085
Teknika
009, 010, 022, 049, 088, 094
Capehart
003
Portland
025, 055, 090
TMK
087, 092
Celebrity
046
Proscan
063, 080
Toshiba
013, 017, 020, 041, 059, 089, 098, 099,
Circuit City
003
Pulsar
060
117
Citizen
029, 030, 031, 032, 034, 038, 047, 049,
Quartz
033
Totevision
007, 087, 088
Quasar
034, 035, 049
Unirech
087
Concerto
003, 030, 031, 032, 038, 047, 049, 050,
122
050, 054, 061, 095, 122, 123
031, 047, 049
001, 002, 021, 081, 087, 088, 091, 094,
Vecrtor Research
005, 062, 085, 089, 090
Colortyme
003, 047, 049, 135
097, 098, 115
Victor
005, 045, 046, 085
Contec
013, 051, 052, 061
088
Video Concepts
005, 027, 085, 089, 090
Cony
051, 052, 061
Randex
088
Videosonic
007, 087
Craig
004, 061
RCA
007, 013, 019, 023, 058, 063, 064, 065,
Wards
013, 021, 023, 087, 088, 089, 091, 094,
Crown
029
097, 118, 119, 120
Curtis Mathes
Radio Shack
Radix
073, 080, 082, 087
Realistic
Ricoh
009, 021, 031, 033, 049, 053, 081, 087,
XR-1000
094
088, 091, 094, 097, 098
Yamaha
004, 005, 006, 026, 062, 085
055
Zenith
060, 078, 079
Salora
033, 041
Samsung
007, 011, 051, 059, 070, 083, 087, 089,
TV
113
Admiral
029, 034, 038, 044, 047, 049, 053, 095,
118
Daewoo
027, 029, 039, 048, 049, 054, 055, 106,
107, 137
Daytron
003, 049
Dimensia
044
045, 121
Dixi
007, 015, 027
046
Sanky
081
Adventura
122
Electroband
Sansui
005, 026, 029, 045, 061, 085, 114
Aiko
054
Electrohome
029, 056, 057, 058, 147
Sanyo
032, 033, 053, 087, 091, 115, 116
Akai
016, 027, 046
Elta
027
SBR
042
Alleron
062
Emerson
029, 051, 059, 060, 061, 062, 118, 123,
Scott
017, 020, 086, 089, 093, 117
A-Mark
007
Sears
013, 023, 028, 031, 033, 053, 054, 088,
Amtron
091, 098, 099, 115
Anam
Sentra
124, 139, 148
061
Envision
038
006, 007, 036
Etron
027
014, 021, 063, 064, 065, 118
055
Anam National
061, 147
Fisher
Sharp
001, 002, 021, 097
AOC
003, 007, 033, 038, 039, 047, 048, 049,
Formenti
155
Shogun
087
133
Fortress
012
Sony
075, 076, 077, 078, 079, 121, 122
007
Fujitsu
004, 062
STS
023
007, 061
Funai
004, 062
Archer
Audiovox
FRANCAIS
Futuretech
004
Minutz
066
SBR
015
GE
020, 036, 037, 040, 044, 058, 066, 088,
Mitsubishi
001, 016, 039, 048, 056, 057, 058, 065,
Schneider
015
ENGLISH
081, 082, 083, 105
Scott
062
000, 015, 029, 031, 039, 048, 051, 056,
Montgomery Ward
011, 020, 144, 145, 146
Sears
008, 014, 021, 022, 023, 024, 025, 040,
057, 067, 068, 069, 116
Motorola
121, 147
Grundy
062
MTC
031, 034, 039, 048, 095
Hitachi
029, 031, 051, 052, 070, 111, 112, 113,
NAD
008, 075, 076, 128
124, *[134]
National
002, 036, 061, 147
151
National Quenties
002
Siemens
Infinity
017, 071
NEC
Janeil
122
119, 120, 125, 147
Goldstar
Hitachi Pay TV
052, 057, 062, 063, 064, 065, 073, 075,
076, 097, 098, 125, 159
Sharp
011, 012, 013, 026, 093, 099, 100, 104,
121
013
031, 038, 039, 048, 057, 084, 086, 135,
Signature
045, 144
147
Simpson
050
JBL
017, 071
Nikko
054
Sony
043, 046, 138, 146, 150
JC Penny
020, 034, 039, 040, 041, 044, 048, 050,
NTC
054
Soundesign
030, 050, 062
058, 066, 069, 076, 088, 090, 095, 125,
Optimus
128
Spectricon
007, 033
136, 159
Optonica
011, 012, 093, 121
Squareview
004
JCB
046
Orion
004, 139
Supre-Macy
032, 122
JVC
019, 051, 052, 072, 073, 091, 117, 126
Panasonic
002, 009, 017, 036, 037, 071, 141, 143,
Supreme
046
Kawasho
018, 046
147
Sylvania
005, 010, 017, 030, 078, 079, 085, 089,
Kenwood
038, 056, 057
Kloss
010, 032
Kloss Novabeam
005, 122, 127, 131
KTV
074, 123
Philco
Philips
101, 127, 131, 132, 145, 155
005, 010, 030, 050, 051, 056, 079, 085,
127, 131, 132, 145, 147
Symphonic
004, 148
005, 015, 017, 050, 051, 056, 078, 087,
Tandy
012, 121
088, 089, 131, 132, 147
Tatung
036, 124
Loewe
071
Pioneer
124, 128, 142
Technics
037
Logik
144
Portland
054
Teknika
001, 030, 032, 034, 052, 054, 078, 083,
Luxman
031
Price Club
095
LXI
008, 014, 017, 024, 040, 044, 063, 071,
Proscan
040, 044, 125
Tera
075, 076, 077, 118, 125
Proton
035, 051, 092, 129
Toshiba
005, 010, 017, 030, 033, 038, 050, 056,
Pulsar
042
071, 078, 079, 085, 089, 108, 109, 110,
Quasar
036, 037, 074, 141
Universal
Magnavox
095, 144, 156, 157
035, 129
008, 014, 034, 063, 075, 076, 095, 097,
136, 158, 159
020, 066, 088
127, 131, 132, 145
Radio Shack
011, 044, 063, 093, 118
Victor
019, 073, 126
Marantz
015, 017, 071, 080
RCA
040, 044, 125, 130, 137, 151, 152
Video Concepts
016
Matsui
027
Realistic
014, 063, 093, 118
Viking
032, 122
Memorex
014, 027, 045, 083, 118, 144
Saisho
027
Wards
005, 045, 066, 078, 085, 088, 089, 093,
Metz
160, 161, 162, 163
Samsung
MGA
001, 039, 048, 056, 057, 058, 065, 081,
Midland
102, 103, 131, 132, 148
003, 015, 034, 053, 055, 057, 094, 095,
136, 153
Zenith
042, 114, 115, 140, 144, 149
Zonda
007
083
Sansui
139
125
Sanyo
013, 014, 021, 022, 063, 064, 081, 096
ENGLISH
FRANCAIS
CABLE
DBS (SATELLITE)
Emerson
004, 005, 006, 007
003, 008, 009, 010
ABC
006, *[007], 008, 009
Alphastar
054
Fisher
Archer
010, 011
Chaparral
035, 036
JVC
018, 019
011, 012, 013, 014, 017
006, 015, 035
Century
011
Dishnet
053
Kenwood
Citizen
011
Drake
037, 038
Magnavox
Colour Voice
012, 013
Echostar Dish
062, 066
Marantz
016, 028, 035
Comtronic
014
GE
048, 055, 056
MCS
016, 024
Eastern
015
General Instruments
039, 040, 041
Onkyo
025, 027
Garrard
011
Grundig
070, 071, 072, 073
Optimus
017, 020, 021, 022, 023
Gemini
030, 033, 034
Hitachi
058, 059
Philips
014, 032, 033, 035
006, 022, 030
General Instrument
030, 031, 032
Hughes Network
063, 064, 065, 069
Pioneer
Hytex
006
JVC
057
Sears
006
023, 031
Jasco
011
Kathrein
074, 075, 076, 083
Sony
Jerrold
009, 016, 017, 026, 032
Magnavox
060
Teac
002, 009, 028
016, 029, 036
Magnavox
018
Nokia
070, 080, 084, 085, 086
Technics
Movie Time
019
Philips
060
Wards
035, 037
NSC
019
Primestar
051
Yamaha
038, 039, 040, 041
Oak
000, 006, 020
Proscan
048, 055, 056
Zenith
042
Panasonic
001, 005
RCA
048, 055, 056, 068
Philips
011, 012, 013, 018, 021
Realistic
042
CDR
Pioneer
002, 003, 022
Sierra I
036
Denon
*[111], 112
Philips
112
RCA
029
Sierra II
036
Regency
015
Sierra III
036
Samsung
014, 023
Sony
049, 067
MD
Scientific Atlanta
004, 024, 025
STS1
043
Denon
113
Signal
014
STS2
044
Kenwood
003, 004
SL Marx
014
STS3
045
Onkyo
007
Starcom
009
SRS4
046
Sharp
005
Stargate
014
Technisat
077, 078, 079, 081, 082
Sony
006
Teleview
014
Toshiba
047, 050
Tocom
007, 016
Uniden
061
TV86
019
Unika
011
CD
Aiwa
001, 002
United Artists
006
Denon
*[111]
Carver
002
Universal
010, 011
Aiwa
001, 035, 043
Harman/Kardon
002, 003
Viewstar
018, 019
Burmster
002
JVC
004, 005
Zenith
027, 028
Carver
003, 035
Kenwood
006
TAPE
Denon
*[111]
FRANCAIS
Magnavox
002
Marantz
002
Onkyo
016, 018
Optimus
007, 008
Panasonic
012
Philips
002
Pioneer
007, 008, 009
Sony
013, 014, 015
Technics
012
Victor
004
Wards
007
Yamaha
010, 011
*[ ] : Preset codes set upon shipment from the factory.
*[ ] : Les codes préréglés diffèrent en fonctiom des livraison de
l’usine.
DVD preset codes
Codes préréglés DVD
B
Model No.
Modéle numéro
111
DVD-555
DVD-755
DVD-900
DVD-910
DVD-955
DVD-1000
DVD-1200
DVD-1500
DVD-1710
DVD-1910
DVD-2200
DVD-2800
DVD-2800II
DVD-2900
DVD-2910
DVD-3800
DVD-3910
DVD-5900
DVD-5910
DVD-9000
DVM-715
DVM-1800
DVM-1805
DVM-1815
DVM-2815
DVM-4800
014
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
ENGLISH
TOKYO, JAPAN
www.denon.com
Denon Brand Company, D&M Holdings Inc.
Printed in China 00D 511 4330 001
Download PDF

advertising