Desa 30LP Electric Heater User Manual

PROPANE
CONSTRUCTION
HEATER
OWNER’S MANUAL
BLP30, RLP30, and REM30LP
IMPORTANT: Read and understand this manual before assembling, starting, or
servicing heater. Improper use of heater can cause serious injury. Keep this
manual for future reference.
GENERAL HAZARD WARNING: FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN
DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM
HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE
POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS
SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER.
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
SAFETY
INFORMATION
WARNINGS
WARNING: FIRE, BURN, INHALATION, AND EXPLOSION
HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE
AWAY FROM THE HEATER AS
RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE
HEATER IN SPACES WHICH DO
OR MAY CONTAIN VOLATILE OR
AIRBORNE COMBUSTIBLES, OR
PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.
WARNING: NOT FOR HOME
OR RECREATIONAL VEHICLE
USE.
The heater is designed for use as a construction
heater in accordance with ANSI Z83.7/
CGA2.14. Other standards govern the use of
fuel gases and heating products for specific
uses. Your local authority can advise you
about these. The primary purpose of construction heaters is to provide temporary heating of
buildings under construction, alteration or repair. Properly used, the heater provides safe
economical heating. Products of combustion
are vented into the area being heated.
We cannot foresee every use which may be
made of our heaters. Check with your local
fire safety authority if you have questions
about heater use.
Other standards govern the use of fuel gases
and heat producing products for specific uses.
Your local authorities can advise you about
these.
Carbon Monoxide Poisoning: Some
people are more affected by carbon monoxide
than others. Early signs of carbon monoxide
poisoning resemble the flu, with headaches,
dizziness, and/or nausea. If you have these
signs, the heater may not be working properly.
Get fresh air at once! Check for proper ventilation and have heater serviced.
Propane Gas: Propane gas is odorless. An
odor-making agent is added to propane gas.
The odor helps you detect a propane gas leak.
However, the odor added to propane gas can
fade. Propane gas may be present even though
no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It is
your guide to safe and proper operation of this
heater.
• Install and use heater with care. Follow all
local ordinances and codes. In the absence
of local ordinances and codes, refer to the
Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58 and
the Propane Gas Installation Code, CAN/
CGA B149.2. This instructs on the safe storage and handling of propane gases.
• Use only the electrical voltage and frequency specified on model plate. The electrical connections and grounding of the
heater shall follow the National Electric
Code, ANSI/NFPA 70 or the Canadian
Electrical Code, Part 1.
• Electrical grounding instructions — This
appliance is equipped with a three-prong
(grounding) plug for your protection
against shock hazard and should be plugged
directly into a properly grounded threeprong receptacle or extension cord.
• Approved by the New York City Fire Department under Certificate of Approval
#4953. To be used only at construction site
with applicable New York City Codes, Regulations, Rules, Directives, Permits, etc.
• This product has been approved for use in
the Commonwealth of Massachusetts.
• This heater produces carbon monoxide,
which is listed by the State of California as
a reproductive toxin under Proposition 65.
• Use only a three-prong, grounded extension cord.
• Use only the hose and factory preset regulator provided with the heater.
• Use only propane gas set up for vapor withdrawal.
• Provide adequate ventilation. Before using
heater, provide at least a one-square-foot
opening of fresh, outside air.
• For indoor use only. Do not use heater outdoors.
• Do not use heater in occupied dwellings or
in living or sleeping quarters.
2
• Do not use heater in basement or below
ground level. Propane gas is heavier than
air. If a leak occurs, propane gas will sink
to the lowest possible level.
• Keep appliance area clear and free from
combustible materials, gasoline, paint thinner, and other flammable vapors and liquids.
• Do not use heater in areas with high dust
content. Dust is combustible.
• Minimum heater clearances from combustibles:
Outlet: 6 Ft.
Sides: 2 Ft.
Top: 6 Ft.
Rear: 2 Ft.
• Keep heater at least six feet from propane
tank(s). Do not point heater at propane
tank(s) within 20 feet.
• Keep propane tank(s) below 100° F.
• Check heater for damage before each use.
Do not use a damaged heater.
• Check hose before each use of heater. If
highly worn or cut, replace with hose specified by manufacturer before using heater.
• Locate heater on stable and level surface if
heater is hot or operating.
• Not intended for use on finished floors.
• Never block air inlet (rear) or air outlet
(front) of heater.
• Keep heater away from strong drafts, water spray, rain, or dripping water.
• Do not leave heater unattended.
• Keep children and animals away from
heater.
• Never move, handle, or service a hot, operating, or plugged-in heater. Severe burns
may result. You must wait 15 minutes after
turning heater off.
• To prevent injury, wear gloves when handling heater.
• Never attach duct work to front or rear of
heater.
• Do not alter heater. Keep heater in its original state.
• Do not use heater if altered.
• Turn off propane supply and unplug heater
when not in use.
• Use only original replacement parts. This
heater must use design-specific parts. Do
not substitute or use generic parts. Improper
replacement parts could cause serious or
fatal injuries.
104163
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
Hot Air Outlet
(Front)
UNPACKING
1.
Outer Shell
Handle
2.
3.
Motor
Remove all packing items applied to
heater for shipment. Keep plastic cover
caps (attached to inlet connector and
hose/regulator assembly) for storage.
Remove all items from carton.
Check all items for shipping damage.
If heater is damaged, promptly inform
dealer where you bought heater.
Piezo Ignitor
Button
Power Cord
Automatic Control
Valve Button
Hose/Regulator
Assembly
Figure 1 - 30,000 BTU/Hr Model
FUNDAMENTALS
OF OPERATION
The Fuel System: The hose/regulator
assembly attaches to the propane gas supply. This provides fuel to the heater.
Fan
Motor
Clean
Heated
Air Out
(Front)
Cool Air
In (Back)
The Air System: The motor turns the fan.
The fan pushes air into and around the
combustion chamber. This air is heated and
provides a stream of clean, hot air.
The Ignition System: The piezo ignitor
lights the burner.
Hose/
Regulator
Assembly
Combustion
Chamber
The Automatic Control System: This
system causes the heater to shut down if the
flame goes out.
Air For Combustion
Figure 2 - Cross Section Operational View
104163
3
Air For Heating
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
ASSEMBLY
PROPANE SUPPLY
1.
1.
Propane gas and propane tank(s) are to be
furnished by the user.
2.
2.
3.
Remove screw from top of fan guard.
Discard screw.
Insert nut clip (provided with handle)
with flat side facing up through slot in
top of shell. Align holes in nut clip with
screw hole behind slot in top of shell.
(see Figure 4).
Place handle over hole and clip. Insert two screws (provided with handle)
through handle and tighten into shell.
Make sure rear screw goes through
shell and into fan guard. Tighten
screws firmly.
Remove
Screw
Figure 3 - Removing Screw from Top of
Fan Guard
Nut Clip
Flat Side Facing Up
Shell
Slot
Use this heater only with a propane vapor
withdrawal supply system. See Chapter 5 of
the Standard for Storage and Handling of
Liquefied Petroleum Gas, ANSI/NFPA 58
and/or CAN/CGA B149.2. Your local library
or fire department will have this booklet.
The amount of propane gas ready for use
from propane tanks varies. Two factors decide this amount:
1. The amount of propane gas in tank(s)
2. The temperature of tank(s)
This heater is designed to operate with a
minimum 20-pound propane tank. You may
need two or more tanks or one larger tank in
colder weather. Use a 100-pound tank for
longer operation or in very cold weather.
Less gas is vaporized at lower temperatures.
Your local propane gas dealer will help you
select the proper supply system. The minimum surrounding air temperature rating for
each heater is -20°F (-29°C).
Average Temp (°F)
At Tank Location
40°
32°
20°
10°
0°
-10°
-20°
No. Of Tanks
(100-pound)
1
1
1
1
1
2
2
INSTALLATION
Figure 4 - Installing Nut Clip
Screws
Handle
WARNING: Review and understand the warnings in the
Safety Information section, page
2. They are needed to safely operate this heater. Follow all local
codes when using this heater.
3.
4.
5.
6.
Provide propane supply system (see
Propane Supply).
Connect POL fitting on hose/regulator
assembly to propane tank(s). Turn POL
fitting counterclockwise into threads on
tank. Tighten firmly using wrench.
IMPORTANT: Position regulator so
that hose leaving the regulator is in a
horizontal position (see Figure 6). This
places the regulator vent in the proper
position to protect it from the weather.
Connect hose to valve inlet (see Figure
7). Tighten firmly using a wrench.
IMPORTANT: Use extra hose or piping if needed. Install extra hose or piping between hose/regulator assembly
and propane tank. You must use the
regulator supplied with heater.
Open propane supply valve on propane
tank(s) slowly. Note: If not opened
slowly, excess-flow check valve on propane tank will stop gas flow. You may
hear a click from the excess-flow check
valve closing. If this happens, reset the
excess-flow check valve by closing propane supply valve and open again slowly.
Check all connections for leaks. Apply
mixture of liquid soap and water to gas
joints. Bubbles forming show a leak
that must be corrected.
Close propane supply valve.
Propane Supply
Valve
Propane
Tank
Regulator
Hose
POL Fitting
Figure 6 - Regulator Position
Nut Clip
Rear of
Heater
Figure 5 - Attaching Handle
WARNING: Test all gas piping and connections for leaks
after installation or servicing.
Never use an open flame to check
for a leak. Apply a mixture of
liquid soap and water to all joints.
Bubbles forming show a leak.
Correct all leaks at once.
4
Figure 7 - Hose and Inlet Connector
104163
OWNER’S MANUAL
VENTILATION
WARNING: Provide at least a
one square foot opening of fresh,
outside air while running heater.
If proper fresh, outside air ventilation is not provided, carbon
monoxide poisoning can occur.
Provide proper fresh, outside air
ventilation before running heater.
OPERATION
6.
WARNING: Review and understand the warnings in the
Safety Information section, page
2. They are needed to safely operate this heater. Follow all local
codes when using this heater.
To Start Heater
1.
2.
3.
4.
5.
Follow all installation, ventilation, and
safety information.
Locate heater on stable and level surface. Make sure strong drafts do not
blow into front or rear of heater.
Plug power cord of heater into a threeprong, grounded extension cord. Extension cord must be at least six feet long.
Extension cord must be UL listed.
Extension Cord Wire Size
Requirements
• Up to 50 ft long, use 18 AWG
rated cord.
• 51 to 100 ft long, use 16 AWG
rated cord.
• 101 to 200 ft long, use 14 AWG
rated cord.
Plug extension cord into a 120 volt/60
hertz, 3-hole, grounded outlet. Motor
will start. Fan will turn, forcing air out
front of heater.
Open propane supply valve on propane
tank(s) slowly. Note: If not opened
slowly, excess-flow check valve on propane tank will stop gas flow. You may
hear a click from the excess-flow check
valve closing. If this happens, reset the
excess-flow check valve by closing propane supply valve and open again slowly.
Piezo
Ignitor
Button
Automatic Control
Valve Button
Figure 8 - Automatic Control Valve Button
and Piezo Ignitor Button
NOTICE: If heater is unplugged or
power outage occurs while heater
is running, the thermal limit device will stop fuel flow. A few seconds occur before the thermal limit
device activates. During this short
time, flames may appear outside
the heater. This is normal. The
flames will go out when thermal
limit device activates.
To Stop Heater
1.
WARNING: Be sure motor and
fan are running before pushing
in automatic control valve button. Flames could flash outside
heater if motor and fan are not
running.
2.
3.
5
Tightly close propane supply valve on
propane tank(s).
Wait a few seconds. Heater will burn
gas left in supply hose.
Unplug heater.
To Restart Heater
1.
2.
104163
Push in and hold automatic control
valve button (see Figure 8). Push piezo
ignitor button (see Figure 8). Keep
pushing ignitor button until the burner
lights. When burner lights, keep automatic control valve button pushed in.
Release button after 30 seconds. This
activates the automatic control system.
Note: If heater fails to ignite, hose may
have air in it. If so, keep automatic control valve button pressed and wait 20 seconds. Release automatic control valve
button and wait 20 seconds for unburned
fuel to exit heater. Repeat this step.
Wait five minutes after stopping heater.
Repeat steps under To Start Heater.
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
STORAGE
CAUTION: Disconnect heater
from propane supply tank(s).
1.
2.
3.
4.
Store propane tank(s) in safe manner.
See Chapter 5 of Standard for Storage
and Handling of Liquefied Petroleum
Gases, ANSI/NFPA 58. Follow all local codes. Always store propane tanks
outdoors.
Place plastic cover caps over brass
fittings on inlet connector and hose/
regulator assembly.
Store in dry, clean, and safe place. Do
not store hose/regulator assembly inside heater combustion chamber.
When taking heater out of storage, always check inside of heater. Insects and
small animals may place foreign objects in heater. Remove motor and other
internal parts if needed to remove foreign objects (see Service Procedures,
page 8).
MAINTENANCE
WARNINGS
• Never service heater while it is
plugged in, connected to propane supply, operating, or hot.
Severe burns and electrical
shock can occur.
• Keep heater clear and free from
combustible materials, gasoline, and other flammable vapors and liquids.
• Do not block the flow of combustion or ventilation air.
1.
2.
3.
Keep heater clean. Clean heater annually or as needed to remove dust and
debris. If heater is dirty or dusty, clean
heater with a damp cloth. Use household cleaners on difficult spots.
Inspect heater before each use. Check
connections for leaks. Apply mixture
of liquid soap and water to connections.
Bubbles forming show a leak. Correct
all leaks at once.
Inspect hose/regulator assembly before each use. If hose is highly worn
or cut, replace with hose specified by
manufacturer.
4.
5.
6.
Have heater inspected yearly by a qualified service agency.
Keep inside of heater free from combustible and foreign objects. Remove
motor and other internal parts if needed
to clean inside of heater (see Service
Procedures, page 8).
Clean fan blades each season or as
needed (see Fan, page 9).
SPECIFICATIONS
Output Rating (BTU/Hr)
30,000
Fuel
Fuel Consumption
Gallons/Hour
Pounds/Hour
Supply Pressure To Regulator
Minimum (for purposes
of input adjustment)
Maximum
Regulator Outlet Pressure
Manifold Pressure
Hot Air Output
(CFM Approx)
Motor
Electric Input
Amperage
Ignition
Weight (Pounds)
Heater
Shipping
Size - L x W x H (Inches)
Heater
Temperature Range for Heater Operation
Propane Vapor Only
.33
1.4
20 psi
Tank Pressure or 200 psi
10 PSI
10.1 PSI
175
3045 RPM
120 volt/60 hertz
.6
Manual, Piezo
9
9.5
18.5 x 7.7 x 12.8
-20° F to 85° F*
* When running heater in temperatures above 85° F, high internal temperatures may cause
thermal limit device to shut down heater.
6
104163
OWNER’S MANUAL
TROUBLESHOOTING
Note: For additional help, visit DESA
International’s Technical Service web
site at www.desatech.com.
WARNING: Never service heater while it is plugged in, connected
to propane supply, operating, or hot. Severe burns and electrical
shock can occur.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Fan does not turn when heater is plugged in.
1. No electrical power to heater
1. Check voltage to electrical outlet. If voltage is good, check heater power cord for
breaks
2. Adjust motor/fan guard to keep fan from
hitting inside of heater shell. Bend fan
guard if necessary
3. Replace fan. See Fan, page 9
4. Replace motor. See Motor, page 8
2. Fan hitting inside of heater shell
3. Fan blades bent
4. Defective motor
Heater will not ignite.
1. User did not follow installation or operation instructions properly
2. No spark at ignitor. To test for spark, follow step 8 under Ignitor, page 10. If you
see spark at ignitor, have heater serviced
by qualified service person. If no spark
seen:
A) Loose or disconnected ignitor wire
B) Wrong spark gap
C) Piezo ignitor loose
D) Bad ignitor electrode
Heater shuts down while running.
1. High surrounding air temperature causing thermal limit device to shut down
heater
2. Restricted air flow
3. Damaged fan
4. Excessive dust or debris in surrounding area
1. Repeat installation and operation instructions. See Installation, page 4 and
Operation, page 5
2. A) Check ignitor wire. Tighten or reattach loose ignitor wire. See Figure
14, page 10 for ignitor wire location
B) Set gap between ignitor electrode and
target plate to .17"
C) Tighten nut holding piezo ignitor to
base of heater
D) Replace ignitor electrode. See
Ignitor, page 10
1. This can happen when running heater in
temperatures above 85°F. Run heater in
cooler temperatures
2 Check heater inlet and outlet. Remove
any obstructions
3. Replace fan. See Fan, page 9
4. Clean heater. See Maintenance, page 6
WARNING: Use only in areas
free of high dust content.
www.desatech.com
104163
7
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
SERVICE
PROCEDURES
You can also visit DESA International’s
Technical Service web site at
www.desatech.com.
WARNING: Never service
heater while it is plugged in, connected to propane supply, operating, or hot. Severe burns and
electrical shock can occur.
ELECTRICAL SYSTEM
The entire electrical system for this heater is
contained within the motor. If any part of the
electrical system is damaged, you must replace motor.
Figure 9 - Removing Motor and Fan Guard from Heater
MOTOR
1.
Remove three screws that attach fan
guard to heater shell.
2. Remove motor and fan guard from
heater shell (see Figure 9).
3. Use hex wrench to loosen set screw
which holds fan to motor shaft (see Figure 10). Remove fan. Be careful not to
damage the fan blade pitch.
4. Remove two nuts and two screws that
attach fan guard to motor using nutdriver. Remove fan guard from motor
(see Figure 11).
5 Disconnect the green power cord wire
from motor and remove black and white
wire terminals.
6. Discard old motor.
7. Attach green power cord wire to motor.
8. Attach fan guard to new motor with two
nuts and two screws.
9. Replace black and white terminals.
10. Place fan onto motor shaft of new motor. Make sure set screw contacts flat
surface on motor shaft. Tighten set
screw firmly (40-50 inch-pounds).
11. Place motor and fan guard into rear of
heater shell. Make sure power cord is
properly located (see Figure 12).
12. Insert three screws through heater shell
and into fan guard. Tighten screws
firmly.
Setscrew
Figure 10 - Setscrew Location
Figure 11 - Removing or Attaching Fan
Guard from Motor
Figure 12 - Replacing Motor and Fan Guard into Heater
8
104163
OWNER’S MANUAL
SERVICE
PROCEDURES
Continued
FAN
1.
Remove three screws that attach fan
guard to heater shell.
2. Remove motor and fan guard from
heater shell (see Figure 13).
3. Use hex wrench to loosen set screw that
holds fan to motor shaft (see Figure 14).
4. Remove fan. Be careful not to damage
the fan blade pitch.
5a. If replacing fan, remove old fan and
discard. Go to step 7 below.
5b. If cleaning fan,use soft cloth moistened
with kerosene or solvent.
6. Dry fan thoroughly.
7. Place fan onto motor shaft. Make sure
set screw contacts flat surface on motor shaft. Tighten set screw firmly (4050 inch-pounds).
8. Place motor and fan guard into rear of
heater shell. Make sure power cord is
properly located (see Figure 15).
9. Insert three screws through heater shell
and into fan guard. Tighten screws
firmly.
Figure 13 - Removing Motor and Fan Guard from Heater
Setscrew
Figure 14 - Setscrew Location
Figure 15 - Replacing Motor and Fan Guard into Heater
Continued
104163
9
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
SERVICE
PROCEDURES
Continued
IGNITOR
1.
2.
3.
4.
5.
6.
7.
8.
Remove motor and fan guard from heater
(see Motor, page 8, steps 1 and 2).
Remove black ignitor wire from piezo
ignitor. Access ignitor wire through underside of heater base (see Figure 16).
Push wire up through notch in filler
panel.
Remove ignitor mounting screw from
rear head using nut-driver or standard
screwdriver (see Figure 17).
Remove ignitor from rear head.
Install new ignitor. Attach ignitor to rear
head with ignitor mounting screw.
Run ignitor wire from new ignitor
through notch in filler panel. Attach ignitor wire to piezo ignitor.
Set gap between ignitor electrode and
target plate to .17" (see Figure 18).
Test for spark.
Piezo Ignitor
Underside of
Heater
Ignitor Wire
Figure 16 - Removing Ignitor Wire from Piezo Ignitor
Mounting Screw
Ignitor
WARNING: Make sure heater
is disconnected from propane
supply. Heater could ignite causing severe burns.
9.
Push piezo ignitor button and watch for
spark between ignitor electrode and
target plate.
Place motor and fan guard into rear of
heater shell (see Motor, page 8, steps 9
and 10).
Figure 17 - Removing Ignitor Mounting Screw and Ignitor
Ignitor Electrode
Gap
Area
Figure 18 - Clearance between Ignitor Electrode and Target Plate
10
104163
OWNER’S MANUAL
ACCESSORIES
Purchase accessories and parts from your
nearest dealer or service center. If they can
not supply an accessory or part, either contact your nearest Parts Central (listed in the
separate Authorized Service Center booklet) or contact DESA International for referral information.
DESA International
P.O. Box 90004
Bowling Green, KY
42102-9004
1-800-972-7879
Parts Department
LPA1020: 10' Rubber Hose with
Brass Fitting U.L. listed.
LPA2170: Propane Gas Regulator
U.L. listed.
LPA3120: Hose/Regulator Assembly U.L. listed.
LPA4020: Fuel Gas Connector
Connects regulator to all standard
propane tanks. U.L. and A.G.A. listed.
REPLACEMENT
PARTS
WARNING: Use only original
replacement parts. This heater
must use design-specific parts.
Do not substitute or use generic
parts. Improper replacement
parts could cause serious or fatal injuries. This will also protect
your warranty coverage for parts
replaced under warranty.
Parts Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
either contact your nearest Parts Central or
call DESA International’s Technical Service
Department at 1-800-323-5190.
When calling DESA International, have
ready
• your name
• your address
• model number of your heater
• how heater was malfunctioning
• purchase date
Parts Not Under Warranty
Contact authorized dealers of this product.
If they can’t supply original replacement
part(s), either contact your nearest Parts
Central (listed in Authorized Service Center booklet) or call DESA International’s
Parts Department at 1-800-972-7879 for
referral information.
When calling DESA International, have
ready
• model number of your heater
• the replacement part number
104163
11
TECHNICAL
SERVICE
You may have further questions about this
heater. If so, contact DESA International’s
Technical Service Department at 1-800323-5190.
You can also visit DESA International’s
Technical Service web site at
www.desatech.com.
30,000 BTU/Hr
PROPANE CONSTRUCTION HEATER
ILLUSTRATED
PARTS
BREAKDOWN
BLP30
RLP30
REM30LP
1
16
6
15
2
13
5
7
8
14
18
19
4
20
12
9
10
22
21
11
3
17
12
104163
OWNER’S MANUAL
PARTS LIST
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 11 of this manual.
BLP30
RLP30
REM30LP
KEY
NO.
PART
NO.
DESCRIPTION
1
2
104154-01
104152-01
104152-02
104152-03
M11143-1
M11084-27
099237-01
103894-01
104162-01
M11084-38
101478-02
104156-01
103863-01
097384-02
101480-12
104786-01
101732-05
103895-01
098219-17
104146-01
104144-01
102445-01
104153-01
M12461-14
Combustion Chamber
Unichassis (BLP30)
Unichassis (RLP30)
Unichassis (REM30LP)
Bushing, Strain Relief
Screw
Thermocouple Nut
Target Bracket Kit
Electrode Ignitor
Hex Tap Screw, #8-18 x 3/8"
Fan
Motor Assembly
Fan Guard
Captive Washer Nut
Wire Assembly
Handle Assembly
Thermal Switch Kit
Rear Head Kit
Cord, Power Supply
Thermocouple
Valve/Orifice/Burner Tube Assembly
Piezo Ignitor Kit
Filler Panel
Hex Screw, 8-32 x 3/8
097647-09
097941-26
099596-15
104161-01
104160-01
Tradename Decal, (BLP30)
Tradename Decal, (RLP30)
Tradename Decal, (REM30LP)
General Information Decal
Operation Decal
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
QTY.
1
1
1
1
1
5
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
PARTS AVAILABLE - NOT SHOWN
2
2
2
1
1
ACCESSORIES
LPA3120
LPA1020
LPA2170
LPA4020
104163
Regulator & Hose Assembly
10' Hose
Regulator
POL Connector
13
1
1
1
1
WARRANTY AND REPAIR SERVICE
KEEP THIS WARRANTY
LIMITED WARRANTY
DESA International warrants this product and any parts thereof, to be free from defects in materials and workmanship for one (1) year from the
date of first purchase when operated and maintained in accordance with instructions. This warranty is extended only to the original retail
purchaser, when proof of purchase is provided.
This warranty covers only the cost of parts and labor required to restore the product to proper operating condition. Transportation and incidental
costs associated with warranty repairs are not reimbursable under this warranty.
Warranty service is available only through authorized dealers and service centers.
This warranty does not cover defects resulting from misuse, abuse, negligence, accidents, lack of proper maintenance, normal wear, alteration,
modification, tampering, contaminated fuels, repair using improper parts, or repair by anyone other than an authorized dealer or service center.
Routine maintenance is the responsibility of the owner.
THIS EXPRESS WARRANTY IS GIVEN IN LIEU OF ANY OTHER WARRANTY EITHER EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DESA International assumes no responsibility for indirect, incidental or consequential damages. Some states do not allow the exclusion or
limitation of incidental or consequential damages, or limitations or exclusions may not apply to you. This Limited Warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
This warranty does not cover discoloration due to operation of heater. We reserve the right to amend these specifications at any time without notice.
The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
WARRANTY SERVICE
Should your heater require service, return it to your nearest authorized service center. Proof of purchase must be presented with the heater. The
heater will be inspected. A defect may be caused by faulty materials or workmanship. If so, DESA International will repair or replace the heater
without charge.
REPAIR SERVICE
Return your heater to your nearest authorized service center. Repairs not covered by the warranty will be billed at standard prices. Each Service
Center is independently owned and operated. We reserve the right to amend these specifications at any time without notice.
Model
Serial No.
Date of Purchase
Complete the following information for future reference.
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
104163 01
NOT A UPC
For information, write: DESA International, P.O. Box 90004
Bowling Green, Kentucky 42102-9004 ATTN: Customer Service Department
When writing, always include model number and serial number.
104163-01
Rev. F
03/00