Installation manual | Desa 50 Electric Heater User Manual

DIRECT-VENT FIREPLACE
OWNER’S OPERATION AND
INSTALLATION MANUAL
NATURAL GAS “TUDOR” MODELS (V)T32N-A SERIES AND CGDV32NR
PROPANE/LP GAS “TUDOR” MODEL (V)T32P-A SERIES
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
WARNING: Improper installation, adjustment, alteration, service or maintenance
can cause injury or property
damage. Refer to this manual
for correct installation and
operational procedures.
For assistance or additional
information consult a qualified installer, service agency
or the gas supplier.
Installation and service
must be performed by a
qualified installer, service
agency or the gas supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance
is not convertible for use with other gases, unless a certified kit is used.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
For more information, visit www.desatech.com
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ..............................................................2
CLEANING AND MAINTENANCE..............................................28
PRODUCT IDENTIFICATION ......................................................3
TROUBLESHOOTING ...............................................................29
LOCAL CODES ............................................................................3
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ........ 32
PRODUCT FEATURES ................................................................4
REPLACEMENT PARTS ............................................................34
PRE-INSTALLATION PREPARATION..........................................4
SPECIFICATIONS ......................................................................34
LOCATION OF TERMINATION CAP............................................6
SERVICE HINTS ........................................................................34
VENTING INSTALLATION INSTRUCTIONS ................................7
TECHNICAL SERVICE ..............................................................34
FIREPLACE INSTALLATION .....................................................16
OWNER'S REGISTRATION FORM ...........................................35
OPERATING FIREPLACE..........................................................24
ACCESSORIES .........................................................................37
INSPECTING BURNERS ...........................................................27
WARRANTY INFORMATION ....................................... Back Page
SAFETY INFORMATION
Natural and Propane/LP Gas: Natural and propane/LP gases are
WARNING: This product contains and/or generates
chemicals known to the State of California to cause
cancer or birth defects or other reproductive harm.
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate or
service this fireplace. Improper use of this fireplace
can cause serious injury or death from burns, fire,
explosions, electrical shock and carbon monoxide
poisoning.
DANGER: Carbon monoxide poisoning may lead
to death!
This fireplace must be installed by a qualified (certified or licensed)
service person. It has a sealed gas combustion chamber that uses a
coaxial pipe (pipe within a pipe and having the same center) venting
system. It brings in fresh air for combustion through the outer pipe and
combustion gases are exhausted through the inner pipe. If the glass
door assembly and venting pipe are not properly seated, connected
and sealed, carbon monoxide leakage (spillage) can occur.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness or nausea.
If you have these signs, the fireplace may not have been installed
properly. Get fresh air at once! Have fireplace inspected and serviced by a qualified service person. Some people are more affected
by carbon monoxide than others. These include pregnant women,
people with heart or lung disease or anemia, those under the influence of alcohol and those at high altitudes.
odorless. An odor-making agent is added to the gas. The odor helps
you detect a gas leak. However, the odor added to the gas can fade.
Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this fireplace.
WARNING: Any change to this fireplace or its
controls can be dangerous.
1.
2.
3.
4.
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
For propane/LP fireplace, do not place propane/LP supply
tank(s) inside any structure. Locate propane/LP supply tank(s)
outdoors. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighborʼs phone.
Follow the gas supplier's instructions
• if you cannot reach you gas supplier, call the fire department.
Never install the fireplace
• in a recreational vehicle
• in windy or drafty areas where curtains or other combustible
(flammable) objects can make contact with the fireplace
front
• in high traffic areas
www.desatech.com
116646-01A
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
SAFETY INFORMATION
PRODUCT IDENTIFICATION
Continued
Upper Louver
Panel
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Flue Collar
3
3
This fireplace reaches high temperatures. Keep children and
adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow
surfaces to cool before touching.
Carefully supervise young children when they are in the room
Nailing
with fireplace.
Do not modify this fireplace under any circumstances. Any Flange
parts removed for servicing must be replaced prior to operating
fireplace.
Log
Turn fireplace off and let cool before servicing, installing or Glass
Set
repairing. Only a qualified service person should install, service Door
or repair this fireplace. Have fireplace inspected annually by a Assembly
qualified service person.
Piezo
Lava
You must keep control compartments, burners and circulating
Ignitor
Rock
air passages clean. More frequent cleaning may be needed due
to excessive lint and dust from carpeting, bedding material, etc.
Turn off the gas valve and pilot light before cleaning fireplace.
Have venting system inspected annually by a qualified service
Control
person. If needed, have venting system cleaned or repaired. See
Valve
Cleaning and Maintenance, page 28.
Grate
Lower
Assembly
Keep the area around your fireplace clear of combustible maLouver Glowing
Embers
terials, gasoline and other flammable vapor and liquids. Do
Panel
not run fireplace where these are used or stored. Do not place
Blower Switch
ON/OFF/REMOTE Switch
items such as clothing or decorations on or around fireplace.
(Optional Installation)
(Optional Installation)
Do not use this fireplace to cook food or burn paper or other
objects.
Figure 1 - Direct-Vent Fireplace with Millivolt Ignition
Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this fireplace. Use only the gas type indicated on fireplace
nameplate.
This appliance, when installed, must be electrically grounded Install and use fireplace with care. Follow all local codes. In the
in accordance with local codes or, in the absence of local absence to local codes, use the current National Fuel Gas Code
codes, with the National Electrical Code, ANSI/NFPA 70 or ANSI Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Installation Code (Canada).
the Canadian Electrical Code, CSA C22.1.
Do not use fireplace if any part has been exposed to or under *Available from:
American National Standards Institute, Inc.
water. Immediately call a qualified service person to arrange
1430 Broadway
for replacement of the unit.
New York, NY 10018
Do not operate fireplace if any log is broken.
National Fire Protection Association, Inc.
Do not use a blower insert, heat exchanger insert or other acBatterymarch Park
cessory not approved for use with this fireplace.
Quincy, MA 02269
Do not operate fireplace with glass door removed, cracked or
broken.
Provide adequate clearances around air openings.
116646-01A
LOCAL CODES
www.desatech.com
4
PRODUCT FEATURES
PRE-INSTALLATION PREPARATION
Location and Space Requirements
PRODUCT FEATURES
These are a few facts that can help you understand and enjoy your
direct-vent fireplace:
• The venting system may be routed to the outside of your home
in several ways. It may vent through the roof (vertical) or it may
vent to an outside/exterior wall (horizontal). The vent pipe installation is very important to allow for proper operation. You must
follow the venting instructions very carefully for either vertical
or horizontal applications.
• This fireplace may be installed in any room of your house provided
all local codes and these installation instructions are followed.
• This fireplace does not require electricity to operate.
• Only the blower requires electricity if installed and if you plan to
install the blower at a later date, do not forget to wire the outlet
at the bottom of the fireplace when framing.
• A piezo ignitor and ceramic electrode create spark to ignite the
pilot light. It does not require any matches, batteries or any other
sources of ignition to light the pilot.
• Each time you turn on your fireplace, you may notice some
amount of condensation on the inside of the fireplace glass. This
is normal and will disappear after 10-20 minutes of operation.
• Your direct-vent gas fireplace system (fireplace and venting) is a
balanced and sealed gas operating unit. It requires approximately 1020 minutes of operating time before the flame pattern stabilizes.
• Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against
any exterior surface on the back, sides or top of your fireplace,
except where standoff spacers are integrally attached. If standoff
spacers are attached to your fireplace, these spacers can be placed
directly against wall or framing material. See framing details on
page 5.
• If you plan on installing a television or entertainment center recessed above your fireplace, it is recommended that you maintain
a minimum 18" above top of louver opening.
• When locating termination cap, it is important to observe the
minimum clearances shown in Figure 7, page 6.
• If recessing into a wall, you can avoid extra framing by positioning your fireplace against an already existing framing member.
• Do not recess termination cap into a wall or siding.
• You may paint the termination cap with 450ºF (232ºC) heatresistant paint to coordinate with the exterior finish.
• There must not be any obstruction such as bushes, garden sheds,
fences, decks or utility buildings within 24" from the front of the
termination cap.
• Do not locate termination cap where excessive snow or ice
build up may occur. Be sure to clear vent termination area after
snow falls to prevent accidental blockage of venting system.
When using snow blowers, do not direct snow towards vent
termination area.
PRE-INSTALLATION
PREPARATION
LOCATION AND SPACE REQUIREMENTS
Determine the safest and most efficient location for your DESA
direct-vent fireplace. Make sure that rafters and wall studs are not
in the way of the venting system. Choose a location where the heat
output is not affected by drafts, air conditioning ducts, windows
or doors. Figure 2 shows some common locations. Be aware of all
restrictions and precautions before deciding the exact location for
your fireplace and termination cap.
When deciding the location of your fireplace, follow these rules:
• Do not connect this fireplace venting to a chimney flue serving
a separate solid-fuel burning fireplace or appliance.
• Due to high temperatures, do not locate this fireplace in high traffic
areas, windy or drafty areas or near furniture or draperies.
• Proper clearances must be maintained.
• If your fireplace is to be installed directly on carpeting, vinyl tile
or any combustible material other than wood, it must be installed
on a metal or wood panel extending the full width and depth of
the fireplace. See Figure 3.
Flush with a wall
Through exterior wall
enclosed in a chase
Corner
installation
Figure 2 - Common Fireplace Locations
1
RW
22
/2"
16D/8"
5
3
34
/8"
FW
Figure 3 - Fireplace Bottom Dimensions
www.desatech.com
116646-01A
PRE-INSTALLATION PREPARATION
5
5
Clearances
Framing and Finishing
PRE-INSTALLATION
PREPARATION
For available accessories for this fireplace, see Accessories on page
37. If you are using a separate combustible mantel piece, refer to
Figure 6 for proper installation height. You can install noncombustible mantels at any height above the fireplace.
Note: Noncombustible mantels may discolor!
Continued
CLEARANCES
Minimum clearances to combustibles for the fireplace are as follows:
*Back and sides
0"/mm
Perpendicular walls
6" (152mm)
Floor
0"/mm
Ceiling to louver opening 42" (1067mm)
Front
36" (914mm)
Top of Standoffs
0"/mm
Vent
(See venting instructions for
specific venting clearances.)
Combustible material with a maximum thickness of 5/8" may be
flush with the top front of fireplace.
* For back and sides of fireplace, do not pack with insulation or
other materials. Zero inch clearance to combustible materials are
for framing purpose only.
NOTICE: This fireplace is intended for use as supplemental heat. Use this fireplace along with your primary
heating system. Do not install this fireplace as your
primary heat source. If you have a central heating
system, you may run system’s circulating blower
while using fireplace. This will help circulate the heat
throughout the house. In the event of a power outage,
you can use this fireplace as a heat source.
13 B5/8"
9D1/2"
39C3/8"
28
A 1/2"
9 7/8"
E
F 3/8"
34
34 5/8"
G
Nailing
Nailing Tabs
Tabs
1
54
H /8"
Figure 5 - Framing Clearances for Corner Installation
1
2
3
A
4
B
FRAMING AND FINISHING
5
C
Figure 4 shows typical framing of this fireplace. Figure 5 shows framing for corner installation. All minimum clearances must be met.
Wall
6
D
E
7
F
G
Top of Louver Opening
Ref. Mantel Depth Ref. Mantel from Top
of Louver Opening
1
2
3
4
5
6
7
323/8"
34 5/8"
17" Horizontal Vent
20" Vertical Vent
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
2" (51mm)
16" (406mm)
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
Figure 6 - Clearances for Combustible Mantels
Figure 4 - Framing Clearances for Installation Against an
Exterior Wall
116646-01A
A
B
C
D
E
F
G
www.desatech.com
6
LOCATION OF TERMINATION CAP
LOCATION OF TERMINATION CAP
N
N
D
H
V
L
E
B
C
Fixed
Closed
F
B
Openable Fixed
Closed
V
Openable
V
I
V
G
B
V
B
B
J
X
V
G
G
M
A
V
K
X
V
A
V TERMINATION CAP
G GAS METER
RESTRICTED AREA
(TERMINATION PROHIBITED)
clearance to service regulator vent outlet [*72 inches (182.9cm)
minimum]
clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other fireplace [*12 inches (30.5cm)
minimum]
clearance to a mechanical air supply inlet [*72 inches (182.9cm)
minimum]
† clearance above paved side-walk or a paved driveway located on
public property [*84 inches (213.3cm) minimum]
clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ‡]
clearance above a roof shall extend a minimum of 24 inches (61cm)
above the highest point when it passes through the roof surface and
any other obstruction within a horizontal distance of 18 inches (45.7cm)
X AIR SUPPLY INLET
A = clearance above grade, veranda, porch, deck, or balcony
I =
[*12 inches (30.5mc) minimum]
B = clearance to window or door that may be opened
J =
[12 inches (30.5cm) minimum]
C = clearance to permanently closed window [minimum 12 inches
(30.5cm) recommended to prevent condensation on window]
K =
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (61cm) from the
L =
center-line of the terminal [18 inches (45.7cm) minimum]
E = clearance to unventilated soffit [12 inches (30.5cm) minimum]
M=
F = clearance to outside corner (see below)
N =
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly within
36 inches (91.4cm) horizontally from the center-line of the regulator
† vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
*
as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.
Note: Local codes or regulations may require different clearances
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Inside Corner
Outside Corner
Recessed Location
D
C
A
C
A = 6" (15.2cm)
E
V
V
V
B = 6" (15.2cm)
B
Balcony with No Side Wall
Balcony with Perpendicular Side Wall
H
G
V
V
G = 12" (30.5cm) minimum clearance
J
Combustible &
Noncombustible
H = 24" (61cm)
J = 20" (50.8cm)
C = Maximum depth of 48" (121.9cm) for
recessed location
D = Minimum width for back wall of
recessed location Combustible - 38" (965mm)
Noncombustible - 24" (61cm)
E = Clearance from corner in
recessed locationCombustible - 6" (15.2cm)
Noncombustible - 2" (5.1cm)
Figure 7 - Minimum Clearances for Termination Cap
www.desatech.com
116646-01A
VENTING INSTALLATION INSTRUCTIONS
Installation Precautions
VENTING INSTALLATION
INSTRUCTIONS
NOTICE: Read these instructions completely before
attempting installation.
These models are tested and approved for use with DESA (directvent) pipe components and terminations.
The venting system must terminate on the outside of the structure and
can not be attached to a chimney or flue system serving a separate
solid fuel or gas burning appliance. A direct-vent appliance must have
its own venting system. DO NOT common vent this appliance.
These models are approved to be vented either horizontally through
an outside wall or vertically through a roof or chase enclosure using
the following guidelines:
• When venting system terminates horizontally on an outside
wall, you may install a standoff if the termination cap is to be
installed directly on a combustible finish such as vinyl, wood,
stucco, etc.
• Never run the vent downward as this may cause excessive temperatures which could cause a fire.
• Vent pipe air space clearances to combustibles are 1" on all sides
except on the horizontal sections, which requires 2" clearance
from the top of the pipe. Where the termination cap penetrates
a combustible wall, 1" air space clearance is required.
• Snorkel terminations are required when minimum clearance to
grade cannot be met (see Figure 16 on page 11).
• Have fireplace and selected vent components on hand to help
determine the exact measurements when elbowing or offsetting.
Always use wall firestops when penetrating walls and firestops
when penetrating ceilings or attic spaces.
• Install horizontal venting with a 1/4" rise for every 12" of run
toward the termination.
INSTALLATION PRECAUTIONS
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
• Installation of any damaged venting component
• Unauthorized modification of the venting system (Do not cut
or alter vent components)
• Installation of any component part not manufactured or
approved by DESA
• Installation other than as instructed by these instructions
WARNING: This gas fireplace and vent assembly
must be vented directly to the outside. The venting
system must NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each
direct-vent gas appliance must use a separate vent
system. Do not use common vent systems.
WARNING: Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal
sections, which require 2" clearances from the top of
the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
do so could result in serious injury, property damage
or loss of life.
NOTICE: Failure to follow these instructions will void
the warranty.
NOTICE: Do not seal termination cap to vent pipe.
Cap must be removable for vent inspection and
maintenance.
116646-01A
7
7
www.desatech.com
8
VENTING INSTALLATION INSTRUCTIONS
Installation Planning
VENTING INSTALLATION
INSTRUCTIONS
Continued
Female
Locking
Lugs
INSTALLATION PLANNING
There are two basic types of direct-vent installation:
• Horizontal Termination
• Vertical Termination
Male
Slots
Horizontal Termination Installation
IMPORTANT: Horizontal square terminations require only inner
portion of wall firestop. Horizontal installations using round termination require exterior portion of wall firestop available only in
vent kit HTK (see Figure 14, page 10).
1. Set the fireplace in its desired location and determine the route
your horizontal venting will take. Do not secure the fireplace
until all venting has been installed. Some installations require
sliding the fireplace in and out of position to make final venting
connections. Figures 14 through 18 on pages 10 through 12 show
different configurations for venting with horizontal termination
that will help you decide which application best suits your installation. Check to see if wall studs or roof rafters are in the path of
your desired venting route. If they are, you may want to adjust
the location of the fireplace.
2. Direct vent pipe sections and components are designed with
special twist-lock connections.
Twist-Lock Procedure: The female ends of the pipes have
locking lugs (indentations). These lugs will slide straight into
matching slots on the male ends of adjacent pipes. Push pipe
sections together and twist one section clockwise approximately one-quarter turn until the sections are fully locked (see
Figure 8). Note: Horizontal runs of vent must be supported
every three feet. Use wall straps for this purpose.
3. Use a 45° elbow to connect venting system to fireplace flue
collar. The elbow is designed to be twist-locked onto the flue
collar as described in step 2. IMPORTANT: Do not attempt
to alter the configuration of the elbow by cutting, twisting,
bending, etc.
4. Assemble the desired combination of pipe and elbows to the
fireplace flue collar. If there are long portions of venting run,
pre-assembled pipe sections may be installed as subassemblies
for convenience.
5. Carefully determine the location where the vent pipe assembly
will penetrate the outside wall. The center of the hole should
line up with the center-line of the horizontal vent pipe. Mark the
wall for a 10 3/4" x 10 3/4" square hole. Cut and frame the square
hole in the exterior wall where the vent will be terminated. If
the wall being penetrated is constructed of noncombustible
material, such as masonry block or concrete, a 8 1/2" hole with
zero clearance is acceptable (see Figure 9).
Figure 8 - Vent Pipe Connections
Vent Opening
Combustible Wall
10 3/4"
(273 mm)
10 3/4" Inside Framing
(273 mm)
10 3/4"
(273 mm)
Vent Opening
Noncombustible Wall
(Framing
Detail)
8 1/2"
(216 mm)
Center
of Hole
Figure 9 - Vent Opening Requirements
www.desatech.com
116646-01A
VENTING INSTALLATION INSTRUCTIONS
9
9
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Cut Siding Away
to Fit Standoff
Continued
Standoff
WARNING: Do not recess vent termination into
any wall. This will cause a fire hazard.
6.
7.
8.
Noncombustible Exterior Wall: Position the horizontal vent
cap in the center of the 8 1/2" round hole and attach to the
exterior wall with four wood screws provided. Before attaching the vent cap to exterior wall, run a bead of non-hardening
mastic (pliable sealant) around the outside edges to make a seal
between it and the outside wall. Note: The four wood screws
provided should be replaced with appropriate fasteners for
stucco, brick, concrete or other types of sidings.
Combustible Exterior Wall: For vinyl siding, stucco or wood
exteriors, a siding standoff may be installed between the vent
cap and exterior wall. The siding standoff prevents excessive
heat from damaging the siding materials. Siding material
must be cut to accommodate standoff. Bolt the vent cap to the
standoff. Apply non-hardening mastic around outside edge of
standoff. Position the standoff/cap assembly in the center of
the 10 3/4" square hole and attach to exterior wall with wood
screws provided (see Figure 11). The siding standoff must sit
flush against the exterior fascia material.
Combustible Exterior Wall Only: Slide the wall firestop over
the vent pipe before connecting horizontal run to vent cap (see
Figure 12).
Carefully move fireplace, with vent assembly attached, toward
wall and insert vent pipe into horizontal termination. The pipe
overlap should be a minimum of 11/4" (see Figure 13, page 10)..
Wood Screw
Vent Cap
Screws
Apply Mastic
to All Four Sides
Figure 11 - Installing Siding Standoff (Combustible
Exterior Wall)
Interior Wall
Surface
Wall
Firestop
Vent Cap
(Horizontal
Termination)
Horizontal
Vent Pipe
Screw
Figure 12 - Connecting Vent Cap with Horizontal Vent Pipe
Vent Cap
Wood Screw
Figure 10 - Installing Horizontal Vent Cap
(Noncombustible Exterior)
116646-01A
www.desatech.com
VENTING INSTALLATION INSTRUCTIONS
10
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
9.
Combustible Exterior Wall Only: Slide wall firestop against
interior wall surface and attach with screws provided. See
Figure 13 for horizontal termination details.
10. Place fireplace into position and shim with noncombustible material if needed. Nail or screw side flanges to framing to secure
unit in place. IMPORTANT: Make sure fireplace is level before
securing. If fireplace is not level it will not work properly.
Minimum Pipe
Overlap 11/4"
Siding Standoff
Screws
Direct Vent
Pipe
WARNING: Never run vent downward as this may
cause excessive temperatures which could cause a
fire. Operation of improperly installed and maintained
venting system could result in serious injury, property
damage or loss of life.
GROUND FLOOR INSTALLATION
Recommended Applications:
• Installation using cabinet surrounds
• Through the wall using round or square termination
(up to 12" horizontal pipe)
• NOT FOR CORNER INSTALLATION
Horizontal High
Wind Square
Termination
45° Elbow
Adjustable
Pipe 12" Max.
Wall
Firestop
Wall Firestop
Square Termination
Vertical (V)
Horizontal (H)
29 /4" min.
17" max.
3
Maintain 1"
Minimum Air
Space Around
Outer Pipe When
Penetrating a Wall
10 /4" x 10 /4"
Framed Opening
3
3
Termination
45° Elbow
Wall
Firestop
Apply Mastic to
Outside Edge of
Standoff
Exterior Portion of
Wall Firestop (Round
Termination Only)
Exterior Wall
with Vinyl Siding
Figure 13 - Typical Horizontal Termination Cap Mounting with
Additional Siding Standoff Installed
Slide Ring Over
Elbow to Complete
Connection
Horizontal Termination Configurations
Figures 14 through 18 show different configurations and alternatives
for venting with horizontal termination. Each figure includes a chart
with critical minimum and maximum dimensions which MUST be
met. IMPORTANT: Remember that a horizontal run of venting must
have a 1/4" rise for every 12" of run toward the termination.
Horizontal
Round
Termination
Round Termination
(Kit HTK Shown)
Figure 14 - Horizontal Termination Configuration for Square or
Round Terminations
NOTICE: Do not seal termination cap to vent pipe.
Cap must be removable for vent inspection and
maintenance.
www.desatech.com
116646-01A
VENTING INSTALLATION INSTRUCTIONS
11
11
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
CORNER INSTALLATION
Recommended Applications:
• Corner ground floor installation
• Ground floor installation where pipe vents horizontally through wall
(over 12" horizontal pipe)
• Basement installation where one foot clearance from ground to
termination is possible
Not to Exceed
(H) Limits
Required
Vertical Pipe Horizontal (H)
None
30" max.
1 ft.
48" max.
2 ft.
60" max.
3 ft.
84" max.
4 ft.
20' max.
* Ground Floor Corner Venting
Not to Exceed
(H) Limits
90° Elbow
Square
Termination
Wall
Firestop
Vertical (V)
*43 3/4" min.
53 3/4" min.
65 3/4" min.
77 3/4" min.
89 3/4" min.
90° Elbow
As Required for (V)
See Chart for Pipe
Section Required
Wall
Firestop
Square
Termination
12" Minimum
45°
Elbow
45° Elbow
Figure 15 - Horizontal Termination Configuration for Corner Installation Using One 90° Elbow
SNORKEL TERMINATION INSTALLATION
Recommended Applications:
• Installations requiring a vertical rise on building exterior
• Any installation using snorkel termination to achieve one foot above ground
Snorkel terminations are available for installations requiring a vertical rise on the exterior of the building. If installing snorkel termination below grade, you must provide proper drainage to prevent water from entering snorkel
termination (see Figure 16). Do not back fill around snorkel termination.
Snorkel Termination
Snorkel
Termination
90° Elbow
12"
Minimum
12"
Minimum
Adequate
Drainage
Figure 16 - Snorkel Termination Configurations for Below Ground Installation
116646-01A
www.desatech.com
45°
Elbow
Wall
Firestop
Snorkel
Termination
12"
Minimum
12
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
HORIZONTAL SYSTEM INSTALLATION USING TWO 90°
ELBOWS
The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows.
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
6' max.
12' max.
18' max.
20' max.
20' max.
Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
6' max.
12' max.
18' max.
20' max.
20' max.
45° Elbow
Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace
www.desatech.com
116646-01A
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination
VENTING INSTALLATION
INSTRUCTIONS
Continued
INSTALLATION FOR VERTICAL TERMINATION
Note: Vertical restrictor must be installed in all vertical installations.
1. Determine the route your vertical venting will take. If ceiling
joists, roof rafters or other framing will obstruct the venting
system, consider an offset (see Figure 19) to avoid cutting
load bearing members. Note: Pay special attention to these
installation instructions for required clearances (air space)
to combustibles when passing through ceilings, walls, roofs,
enclosures, attic rafters, etc. Do not pack air spaces with insulation. Also note maximum vertical rise of the venting system
and any maximum horizontal offset limitations.
2. Set the fireplace in desired location. Drop a plumb line down
from the ceiling to the position of the fireplace exit flue. Mark
the center point where the vent will penetrate the ceiling. Drill
a small locating hole at this point.
Drop a plumb line from the inside of the roof to the locating
hole in the ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
2.
3.
4.
5.
6.
Roof Flashing
7.
Assemble the desired lengths of pipe and elbows necessary to
reach from the fireplace flue up through the firestop. Be sure all
pipe and elbow connections are fully twist-locked (see Figure
8, page 8).
Cut a hole in the roof using the locating hole as a center point.
(Cover any exposed open vent pipes before cutting hole in roof.)
The 10 3/4"x10 3/4" hole must be measured on the horizontal;
actual length may be larger depending on the pitch of the roof.
There must be a 1" clearance from the vent pipe to combustible
materials. Frame the opening as shown in Figure 9, page 8.
Connect a section of pipe and extend up through the hole.
Note: If an offset is needed to avoid obstructions, you must
support the vent pipe every 3 feet. Use wall straps for this
purpose (see Figure 19). Whenever possible, use 45° elbows
instead of 90° elbows. The 45° elbow offers less restriction to
the flow of the flue gases and intake air.
Place the flashing over the pipe section(s) extending through
the roof. Secure the base of the flashing to the roof and framing
with roofing nails. Be sure roofing material overlaps the top
edge of the flashing as shown in Figure 19. There must be a
1" clearance from the vent pipe to combustible materials.
Continue to add pipe sections until the height of the vent cap
meets the minimum building code requirements described in
Figure 7 on page 6. Note: You must increase vent height for
steep roof pitches. Nearby trees, adjoining rooflines, steep
pitched roofs and other similar factors may cause poor draft or
down-drafting in high winds. Increasing the vent height may
solve this problem.
Twist-lock the vent cap onto the last section of vent pipe.
Note: If the vent pipe passes through any occupied areas above the
first floor, including storage spaces and closets, you must enclose
pipe. You may frame and sheetrock the enclosure with standard
construction material. Make sure and meet the minimum allowable clearances to combustibles. Do not fill any of the required air
spaces with insulation.
Wall Strap
45° Elbow
If area above is a room or
insulated area, install firestop
above framed hole.
Ceiling Firestop
Figure 19 - Offset with Wall Strap and 45° Elbows
Flat Ceiling Installation
1.
Cut a 10 3/4" square hole in the ceiling using the locating hole as
a center point. The opening should be framed to 10 3/4"x10 3/4"
(273mm x 273mm) inside dimensions, as shown in Figure 9 on
page 8 using framing lumber the same size as the ceiling joists.
If the area above the ceiling is an insulated ceiling or a room,
nail firestop from the top side. This prevents loose insulation
from falling into the required clearance space. Otherwise, install
firestop below the framed hole. The firestop should be installed
with no less than three nails per side (see Figure 20).
116646-01A
13
13
Figure 20 - Installing Firestop
www.desatech.com
If area above is not a room, install
firestop below framed hole.
14
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Venting with One 90° Elbow
Continued
Vertical Termination Configurations
Figures 21 through 24 show four different configurations for vertical termination.
Vertical (V)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
Note: Install
restrictor into inner
collar of fireplace
as shown.
45° Elbow
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
Note: Install
restrictor into inner
collar of fireplace
as shown.
Figure 22 - Vertical Venting Configuration Using One 90° Elbow
(Vertical Round High Wind Termination Shown)
Venting with Two 90° Elbows
Vertical (V1)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
6' max.
12' max.
18' max.
20' max.
Note: Install restrictor
into inner collar of
fireplace as shown.
Figure 21 - Vertical Venting Configuration Using Two 90°
Elbows with Two Horizontal Runs (Vertical Round High Wind
Termination Shown)
45° Elbow
Note: Vertical (V1) + Vertical (V2) = 40' max.
Figure 23 - Vertical Venting Configuration Using Two 90° Elbows
(Vertical Round High Wind Termination Shown)
www.desatech.com
116646-01A
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
High Altitude Installation
VENTING INSTALLATION
INSTRUCTIONS
Continued
HIGH ALTITUDE INSTALLATION
Your DESA direct-vent fireplace has been tested and approved for
elevations from 0-2000 feet (USA) and elevations from 0-4500
feet (Canada) .
When installing this fireplace at an elevation above 2000 feet (in
the USA), you may need to decrease the input rating by changing
the existing burner orifice to a smaller size. Reduce input 4% for
each 1000 feet above sea level. Check with your local gas company
for proper orifice size identification.
When installing this fireplace at an elevation above 4500 feet (in
Canada), check with local authorities.
Consult your local gas company to help determine the proper orifice
for your location.
For assistance with any high altitude installation contact DESAʼs
Customer Service Department at 1-866-672-6040.
Vertical Venting
V = 40' max.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Figure 24 - Vertical Venting Configuration With No Horizontal
Run (Vertical Round High Wind Termination Shown)
116646-01A
15
15
www.desatech.com
16
VENTING INSTALLATION INSTRUCTIONS
Parts List for Venting Kits and Components
FIREPLACE INSTALLATION
Check Gas Type
Installing Optional Blower Accessories
VENTING INSTALLATION
INSTRUCTIONS
FIREPLACE INSTALLATION
Continued
Use proper gas type for the fireplace unit you are installing. If you have
conflicting gas types, do not install fireplace. See retailer where you
purchased the fireplace for proper fireplace according to your gas type
or to purchase gas conversion kit (see Accessories, page 37).
PARTS LIST FOR VENTING KITS AND
COMPONENTS
DESA (5/8") Pipe & Vent Kits
Number Description
P58-6
P58-12
P58-24
P58-36
P58-48
PA58-712
E58-45
E58-90
VKG-58
VKB-58
VKS-58
VKR-58
VKC-58
HTK-58
HT-58
HTS-58
HTKS-58
VT-58
ST-58-14
ST-58-36
SC-58
WF-58
RF-58-6
RF-58-12
VR-58
S-58
WS-58
CS-58
FP-58
SF-58
6" Section Double Wall Pipe, Galvanized
12" Section Double Wall Pipe, Galvanized
24" Section Double Wall Pipe, Galvanized
36" Section Double Wall Pipe, Galvanized
48" Section Double Wall Pipe, Galvanized
Adjustable 7"-12" Section Double Wall Pipe,
Galvanized
45° Elbow, Galvanized
90° Elbow, Galvanized
Ground Floor Vent Kit, Galvanized (Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall Firestop, Horizontal
Square Termination, 16 Screws)
Basement Vent Kit, Galvanized (Includes: 45° Elbow,
7"-12" Adjustable Pipe, Wall Firestop, Horizontal
Square Termination, 4' Pipe, 90° Elbow, 20 Screws)
Snorkel Vent Kit, Galvanized (Includes: 45° Elbow,
7"-12" Adjustable Pipe, Wall Firestop, 36" Snorkel
Termination, 4' Pipe, 1' Pipe, 90° Elbow, 26 Screws)
Roof Vent Kit, Galvanized (Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Flue Restrictor, Vertical High Wind
Termination, 2' Pipe, 4' Pipe, Wall Firestop, Storm
Collar, Roof Flashing [0/12 - 6/12], 26 Screws)
Corner Vent Kit, Galvanized (Includes 45° Elbow,
7"-12" Adjustable Pipe, Wall Firestop, Horizontal
Termination, 6" Pipe, 90° Elbow, 18 Screws)
Horizontal Round Termination Kit (Includes Round
Termination, Wall Firestop, 45° Elbow)
Horizontal Round Termination, Galvanized
Horizontal Square Termination, Galvanized
Horizontal Square Termination Kit (Includes: Square
Termination, Wall Firestop, 45° Elbow)
Vertical Round Termination, Galvanized
14" Snorkel Termination, Galvanized
36" Snorkel Termination, Galvanized
Storm Collar, Galvanized
Wall Firestop, Galvanized
Roof Flashing - 0 to 6/12 Pitch, Galvanized
Roof Flashing - 6/12 to 12/12 Pitch, Galvanized
Vertical Restrictor, Galvanized
Vinyl Siding Standoff, Galvanized
Wall Strap
Cathedral Ceiling Support
Firestop Plate
Stucco Flashing - For use with HTS-58
.CHECK
GAS TYPE
INSTALLING OPTIONAL BLOWER
ACCESSORIES
NOTICE: If installing blower in an existing fireplace
with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex electrical outlet
installed in the right side of the bottom of the fireplace
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
Model BK Installation
Follow all instructions provided in the blower accessory kit.
1. Attach the power cord to the blower motor by firmly pushing the
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25).
2. Attach green ground wire from power cord to blower housing using screw provided (see Figure 25). Tighten screws
securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward. The blower will
fit inside the back opening and be held in position against the
back wall by the magnets (see Figure 25).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green
ground wire is tight.
Blower
Location
Lower Firebox
Cavity
Side View
Magnetic
Strips
Spade Terminals
Green Ground Wire
Screw
Exhaust Port
Figure 25 - Blower Model BK
www.desatech.com
116646-01A
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
FIREPLACE INSTALLATION
Continued
5.
6.
7.
8.
Mount speed control box to switch bracket by placing the plastic
control shaft forward through the round opening in the switch
bracket (see Figure 26).
While supporting speed control, secure control shaft with lock nut
by pushing and turning lock nut with pliers clockwise until it is
tight against front panel. Place control knob provided on shaft.
Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
Plug in blower power cord.
a. If your firebox is installed as a freestanding unit with an
accessory mantel, determine whether the power cord will
exit the left side or the right side of the firebox. Route power
cord through exit hole and plug the power cord into a wall
receptacle near the firebox.
b. If your firebox installation is recessed and/or pre-wired, plug
the power cord into the duplex outlet provided. Refer to your
firebox ownerʼs manual for instructions on wiring the duplex
outlet.
CAUTION: Never touch the blower wheel while
in operation.
9.
Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Turn blower on and check for operation. Turn blower off
by turning knob fully counterclockwise before continuing.
10. Peel off the backing paper and stick the supplied wiring diagram
decal on the firebox bottom approximately 12" in front of the
blower (see Figure 27).
Speed Control
Switch
Bracket
Model BKT Installation
Note: When installing the BKT thermostatically-controlled blower,
you must first secure the thermal switch bracket to the blower if it
has not already been factory installed.
1. Place the green ground wire with ring terminal between the
bottom hole on the thermal switch bracket and the top ear hole
on the blower assembly. Insert the phillips screw into all three
pieces and tighten securely (see Figure 28).
2. Connect wire harness and power cord terminals. Connect the
blue jumper wire to the blower motor terminal and the right
side terminal of the thermal switch. Connect the black wire to
the left side of the thermal switch and the white wire to the
other remaining blower motor terminal.
Note: The power cord outer insulation sleeve may have to be
stripped slightly to allow enough wire length to reach and make
all connections. DO NOT trim excessive length away. Just enable
enough to make all connections securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward and the thermodisc
positioned up near the fireplace bottom. The thermodisc must
be oriented near the fireplace bottom as shown in Figure 28 in
order to sense temperature and properly operate. The blower
will be held in position against the back wall by the magnets
incorporated onto the blower housing (see Figure 28).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and thermal switch and that the screw
for the thermodisc bracket and green ground wire is tight.
White Wire
Blue Wire
Power Cord
Thermal
Switch
Bracket
Magnetic
Strips
Air Flow
Direction
Black
Wire
Blower
Plug-In
17
17
Phillips
Screw
Control
Knob
Locknut
Control
Shaft
Duplex Outlet
(Located underneath
firebox floor against
lower right outside wall)
Figure 26 - Attaching Speed Control to Firebox
110
V.A /11
.C. 5
Bla
Wh ck
ite
Ring Terminal
on Green Wire
Air Flow Direction
Magnets
Thermodisc
Side View Firebox Bottom
Fa Var
n iab
Sw le
itch
On
ck
Bla
ck
Off
Route BKT
Blower Through
This Area
Bla
Bla
Wh ck
Gre ite
en
Thermal Switch
Blo
Mo we
tor r
Figure 28 - Blower Model BKT
Wiring Diagram Decal
12" in Front of Blower
Figure 27 - Location of Wiring Diagram Decal (Model May Vary
From Illustration)
116646-01A
www.desatech.com
Blower
Location
18
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
Installing Gas Piping to Fireplace Location
FIREPLACE INSTALLATION
Continued
Mount the speed control box against the mounting plate provided
in the lower fireplace cavity by placing the plastic control shaft
forward through the round hole (see Figure 26, page 17).
6. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until
it is tight against mounting plate. Place control knob provided
on shaft (see Figure 26, page 17).
7. Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Also double check all wire leads and make sure wire routing
is not pinched or in a precarious position. Correct accordingly.
8. Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
9. Plug in blower power cord to duplex outlet.
10. The blower will only run when the speed control knob is in the
ON position and the thermal switch senses temperature after the
fireplace begins to heat up. The blower speed can be adjusted by
rotating the control knob. To turn off, turn knob fully counterclockwise until it clicks off. If the blower is ON and has been running
with the fireplace operating, the blower will continue to run for a
short time after the fireplace has been turned off. As the thermal
switch cools down, the blower shuts down automatically.
11. Peel off the backing paper and stick the supplied wiring diagram
decal on the firebox bottom approximately 12" in front of the
blower (see Figure 27, page 17).
5.
Blower Wiring Diagram
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
Variable
Fan Switch
Off
1
2
Fan Switch
(N.O.)
WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.
CAUTION: For propane/LP units, never connect
fireplace directly to the propane/LP supply. This
heater requires an external regulator (not supplied).
Install the external regulator between the fireplace
and propane/LP supply.
Installation Items Needed
Before installing fireplace, make sure you have the items listed
below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local
codes)
* A CSA design-certified equipment shutoff valve with 1/8" NPT tap
is an acceptable alternative to test gauge connection. Purchase the
CSA design-certified equipment shutoff valve from your retailer.
For propane/LP connection only, the installer must supply an external regulator. The external regulator will reduce incoming gas
pressure. You must reduce incoming gas pressure to between 11
and 14 inches of water. If you do not reduce incoming gas pressure,
fireplace regulator damage could occur. Install external regulator
with the vent pointing down as shown in Figure 30. Pointing the
vent down protects it from freezing rain or sleet.
Black
Propane/LP
Supply Tank
On
110/115
V.A.C.
INSTALLING GAS PIPING TO FIREPLACE
LOCATION
External
Regulator
Blue
Black
White
Green
Blower
Motor
Figure 29 - Blower Wiring Diagram for Thermostat-Controlled
Models
Vent
Pointing
Down
Figure 30 - External Regulator with Vent Pointing Down
(Propane/LP Only)
www.desatech.com
116646-01A
FIREPLACE INSTALLATION
Installing Gas Piping to Fireplace Location (Cont.)
Connecting Fireplace to Gas Supply
Checking Gas Connections
19
19
FIREPLACE INSTALLATION
CONNECTING FIREPLACE TO GAS SUPPLY
Continued
Installation Items Needed
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter
or greater to allow proper gas volume to fireplace. If
pipe is too small, undue loss of volume will occur.
Installation must include an equipment shutoff valve, union and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from fireplace (see Figure 31).
IMPORTANT: Install main gas valve (equipment shutoff valve)
in an accessible location. The main gas valve is for turning on or
shutting off the gas to the appliance.
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower louver door panel by gently pulling forward.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to fireplace. Route flexible gas supply line through
one of the access holes on side of fireplace.
3. Attach flexible gas line from gas supply to control valve (see
Figure 32).
4. Check all gas connections for leaks. See Checking Gas
Connections.
To Gas Supply
(Natural)
Check your building codes for any special requirements for locating
equipment shutoff valve to fireplaces.
To External
Regulator
(Propane/LP)
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.
Figure 32 - Connecting Flexible Gas Line to Millivolt Valve
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections ,
internal and external to unit, for leaks after installing
or servicing. Correct all leaks at once.
CSA Design-Certified
Equipment Shutoff Valve
with 1/8" NPT Tap*
Approved Flexible
Gas Line
3" Minimum
Natural - From
Gas Meter (5.5"
W.C. to 10.5"
W.C. Pressure)
Propane/LP
From External
Regulator (11"
W.C. to 14" W.C.
Pressure)
WARNING: Never use an open flame to check for
a leak. Apply noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak. Correct all leaks
at once.
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
2.
3.
Cap
Figure 31 - Gas Connection
Pipe Nipple
Tee Joint
Sediment Trap/Drip Leg
* The CSA design-certified equipment shutoff valve may be supplied
with the appliance or you can purchase it from your retailer.
116646-01A
Control Valve
Flexible Gas Line
Do NOT Kink
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 31. Locate sediment trap/drip leg where it
is within reach for cleaning. Install in piping system between fuel
supply and fireplace. Locate sediment trap/drip leg where trapped
matter is not likely to freeze. A sediment trap traps moisture and
contaminants. This keeps them from going into fireplace gas controls. If sediment trap/drip leg is not installed or is installed wrong,
fireplace may not run properly.
Equipment
Shutoff Valve
4.
Disconnect fireplace and its individual equipment shutoff valve
from gas supply piping system. Pressures in excess of 1/2 psig
(3.5 kPa) will damage fireplace gas regulator.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace
or using compressed air.
Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show
a leak. Correct all leaks at once.
www.desatech.com
20
FIREPLACE INSTALLATION
Checking Gas Connections (Cont.)
Installing Optional Wall Mount Switch - GWMS2
FIREPLACE INSTALLATION
Continued
5.
Reconnect fireplace and equipment shutoff valve to gas supply.
Check reconnected fittings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
Close equipment shutoff valve (see Figure 33).
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace
or using compressed air.
Check all joints from propane/LP supply tank or gas meter
to equipment shutoff valve (see Figure 34, for propane/LP or
Figure 35, for natural gas). Apply noncorrosive leak detection
fluid to all joints. Bubbles forming show a leak. Correct all
leaks at once.
Equipment
Shutoff
Valve
Open
Pressure Testing Fireplace Gas Connections
1.
2.
3.
4.
5.
6.
INSTALLING OPTIONAL WALL MOUNT
SWITCH - GWMS2
1.
2.
Closed
Figure 33 - Equipment Shutoff Valve
3.
Propane/LP
Supply Tank
Equipment
Shutoff
Valve
Open equipment shutoff valve (see Figure 33).
Open propane/LP supply tank valve for propane/LP fireplace
or main gas valve located on or near gas meter for natural gas
fireplace.
Make sure control knob of fireplace is in the OFF position.
Check all joints from equipment shutoff valve to gas valve (see
Figure 34 for propane/LP or Figure 35 for natural gas). Apply
noncorrosive leak detection fluid to all joints. Bubbles forming
show a leak. Correct all leaks at once.
Light fireplace (see Operating Fireplace, page 24). Check all
other internal joints for leaks.
Turn off fireplace (see To Turn Off Gas to Appliance, page 2).
4.
Connect one terminal of 25 ft. wire for the wall switch to the
TPTH terminal on the valve. Connect remaining wire terminal to
the TH terminal on the valve. Make sure that the wire terminals
are in the positions on the unit as pictured in Figure 36. If wires
are not connected as shown the switch will not work.
Route the 25 ft. wire through openings provided on the sides
of the burner system to a convenient location to mount your
switch.
Connect one bare wire end to each of the terminals of the
GWMS2 wall switch.
Install the wall switch and cover in the wall.
To Wall Switch
Accessory
Gas Valve
Figure 36 - Connecting Wall Switch to Control Valve
Figure 34 - Checking Gas Joints for Propane/LP Gas
Fireplace
Equipment
Shutoff
Valve
Gas
Meter
Gas Valve
Figure 35 - Checking Gas Joints for Natural Gas Fireplace
www.desatech.com
116646-01A
FIREPLACE INSTALLATION
Installing Optional Wireless Hand-Held Remote Control - GHRCB and GHRCTB Series
Removing/Replacing Glass Door
FIREPLACE INSTALLATION
Continued
INSTALLING OPTIONAL WIRELESS HANDHELD REMOTE CONTROL - GHRCB AND
GHRCTB SERIES
NOTICE: Use only alkaline batteries (not included).
Installing Remote Receiver
1.
2.
3.
4.
5.
6.
Open bottom louver and locate the switch bracket on the left.
Unscrew the switch bracket. Lean bracket forward so you are
able to access the back of the remote receiver.
Locate the battery clip mounted on the back of the receiver.
Slide a 9-volt alkaline battery (not included) through the clip
(see Figure 37).
Attach the terminal wires to the battery.
Connect wires from receiver to TH and TPTH to control valve
(see Figure 38).
Replace the switch bracket.
21
21
Remote Control Unit
Battery Cover
Terminal
Wires
9-Volt
Alkaline
Battery
Battery
Housing
Figure 39 - Installing Alkaline Battery in Hand-Held Remote
Control Unit (GHRCB)
9-Volt
Battery
Terminal
Wires
Remote
Control
Unit
Battery
Cover
Figure 40 - Installing Battery in Hand-Held Remote Control Unit
(GHRCTB Series)
REMOVING/REPLACING GLASS DOOR
CAUTION: Do not operate this fireplace with a
broken glass door panel or without the glass door
panel securely in place. For replacement part information see Replacement Parts, page 34.
Receiver
9-Volt Alkaline
Battery
Terminal Wires
Battery Clip
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
Figure 37 - Attaching Alkaline Battery to Receiver
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before removing
glass door or louvers.
To Optional
To Wall
Remote
Thermostat
Accessory
Removing Louver Panels
Figure 38 - Control Valve Terminals
Installing 9-Volt Alkaline Battery in Hand-Held
Remote Control Unit
1.
2.
3.
Remove battery cover on back of remote control unit.
Attach terminal wires to a 9-volt alkaline battery (not included).
Place battery into the battery housing.
Replace battery cover onto remote control unit.
Remove the top and bottom louver panels by simultaneously pulling
both top end spring latches towards the center of the appliance until
they are disengaged from the locating holes (see Figure 41). Repeat
for bottom spring latches and pull the louvers outward. To install or
replace items removed, simply reverse the procedures above.
Louver Panel
Spring Latch
Figure 41 - Removing Louver Panel
116646-01A
www.desatech.com
FIREPLACE INSTALLATION
22
Removing/Replacing Glass Door (Cont.)
Installing Optional Brick Liner Model BL32D
FIREPLACE INSTALLATION
Continued
INSTALLING OPTIONAL BRICK LINER
MODEL BL32D
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before installing
brick liner.
Removing Glass Door
If replacement of glass is necessary, the entire assembly, glass and
frame, must be replaced. If glass is broken, wear gloves and tape
the remaining fragments onto the frame.
1. Remove screen assembly by pushing the rod either left or right
and then down and forward to remove screen/rod assembly
from the firebox. Set assembly aside.
2. Lift up on latches to unlock. There are two on top of firebox and
two below firebox that hold glass door in place (see Figure 42).
3. While holding glass door to prevent it from falling and causing
injury, remove the five screws from the hinge located on the
left side of door frame assembly (see Figure 42).
4. Remount the new frame at the hinge with five new screws
before closing door. This will ensure seating of the gasket.
5. Close glass door frame. Lock latches by placing the bar under the
tab on door and pushing down and back on latch (see Figure 42).
6. Replace screen/rod assembly by reversing step 1.
7. Replace louvers by reversing procedure under Removing
Louver Panels, page 21.
Unlock
Lock
Latch
Screw
This brick liner kit is optional. You may purchase brick liner from
your local retailer or see page 37.
CAUTION: Always handle brick panels with two
hands. Do not force brick panels into place. Excessive force will break brick panels.
1.
2.
Remove top and bottom louvers to allow access to door latches.
Unlock door latches and open glass door. See steps 1 and 2 of
Removing/Replacing Glass Door, column 1.
3. If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs,
lava rock and ember material.
4. Remove three screws from deflector shield on the inside top
of firebox. Set shield and screws aside.
5. Install rear brick panel first. Rest bottom edge of panel on back
edge of grate (see Figure 43).
6. Install left side brick panel by sliding it between the grate and
the side of the firebox (see Figure 44, page 23).
7. Install the right brick panel using the same method described
8. Replace deflector shield using screws removed in step 4.
9. Follow instructions on page 23 to install logs, lava rock and
ember material.
10. Close glass door, lock latches on top and bottom of door and
replace screen (see steps 5 and 6 of Removing Glass Door,
column 1).
11. Close top and bottom louvers.
Hinge
Glass Frame
Assembly
Rear Brick Panel
Figure 42 - Removing/Replacing Glass Door
Cleaning Glass Door
See Cleaning and Maintenance on page 28.
Figure 43 - Installing Rear Brick Panel
www.desatech.com
116646-01A
FIREPLACE INSTALLATION
Installing Optional Brick Liner Model BL32D (Cont.)
Installing Logs, Lava Rock and Glowing Embers
FIREPLACE INSTALLATION
Continued
2.
3.
4.
Rest log #2 (large front log) on the pins on the front part of the
grate (see Figure 46).
Place log #3 (crossover log) onto the rear and front logs. Make
sure it is seated properly on the smooth surface on the front log
and on the pin on the back log as shown in Figure 47.
Place log #4 (right log) on the pin on the right side of front log
as shown in Figure 48.
2
Left Side
Brick Panel
Figure 44 - Installing Side Brick Panels
INSTALLING LOGS, LAVA ROCK AND
GLOWING EMBERS
Figure 46 - Installing Log No. 2
Each log is marked with a number. These numbers will help you
identify the log when installing. It is very important to install these
logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace.
3
Open louvers, remove screen, unlock door latches and open glass
door. See steps 1 and 2 of Removing Glass Door, page 22. Install
logs according to instructions for fireplace model numbers.
1. Place log #1 (rear log) on top of grate. Make sure the notches
in the bottom of the log fit over the grate (see Figure 45).
1
Figure 47 - Installing Log No. 3
4
Figure 45 - Installing Log No. 1
Figure 48 - Installing Log No. 4
116646-01A
23
23
www.desatech.com
24
OPERATING FIREPLACE
Installing Logs, Lava Rock and Glowing Embers (Cont.)
For Your Safety Read Before Lighting
Lighting Instructions
FIREPLACE INSTALLATION
OPERATING FIREPLACE
Continued
5.
6.
7.
8.
9.
Place log #5 (base log) onto the front left part of the grate
making sure the notches fit over the prongs of the grate). See
Figure 49.
Place log #6 (left log) onto two pins on the left side of back
and front log. See Figure 49.
Place lava rock along sides and front of firebox bottom in areas
that are visible only. It is not necessary to use all of the lava
rock provided.
Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between
the burner and grate prongs (see Figure 50). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember
material in one area. It is not necessary to use all of the ember
material provided.
Close glass door, lock door latches, replace screen and close
louvers (see steps 5 and 7 of Removing Glass Door, page 22).
6
5
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
1.
2.
3.
4.
Figure 49 - Installing Logs No. 5 and No. 6
5.
6.
7.
STOP! Read the safety information above.
Open lower louver panel.
Turn off all electric power to the fireplace.
Push in gas control knob slightly and turn clockwise
to “OFF”.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow
“B” in the safety information above. If you don't smell gas,
go to the next step.
The pilot is located by the main burner and should not
require accessing for lighting.
to “PILOT”
Turn gas control knob counterclockwise
(see Figure 51, page 25).
Ember Material
Figure 50 - Placing Ember Material on Burner
www.desatech.com
116646-01A
25
25
OPERATING FIREPLACE
Lighting Instructions (Cont.)
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Hand-Held Remote Operation
OPERATING FIREPLACE
MANUAL LIGHTING
PROCEDURE
Continued
Push in gas control knob all the way and hold. Immediately
light the pilot by repeatedly depressing the piezo spark
ignitor until a flame appears. Continue to hold for about
one (1) minute after the pilot is lit. Release gas control knob
and it will pop back. Pilot should remain lit. If it goes out,
repeat steps 4 through 8.
• If gas control knob does not pop up when released, stop and
immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician
or gas supplier.
9. Turn on all electric power to the fireplace.
to “ON”.
10. Turn gas control knob counterclockwise
11. This valve is equipped with a HI/LO feature. Set fireplace
input as desired.
12. Close lower louver panel.
8.
Variable Control Knob
You may shut off the burners and keep the pilot lit by doing
one of the following:
to the PILOT position.
1. Turn gas control knob clockwise
2. Set selector switch in the OFF position.
116646-01A
Blower Control Knob
(Optional Accessory)
OFF
Variable
Control Knob
ON
Selector Switch
in Remote
Position
N
O
Shutting Off Burners Only (pilot stays lit)
IMPORTANT: Do not leave the selector switch in the REMOTE
or ON position when the pilot is not lit. This will drain the
battery.
HI
Open lower louver panel.
Set selector switch in the OFF position to prevent draining
battery.
Turn off all electrical power to the appliance if service is to
be performed.
Push in gas control knob slightly and turn clockwise
to “OFF”.
Close lower louver panel.
LO
5.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instructions, page 24.
O
TO TURN OFF GAS
TO APPLIANCE
4.
Note: All remote control accessories must be purchased separately (see Accessories, page 36). Follow instructions included
with the remote control.
OT
Figure 51 - Control Valve
3.
OPTIONAL HAND-HELD
REMOTE OPERATION
ON
OFF
REMOTE
OFF
LO
1.
2.
5.
After lighting, let pilot flame burn for about one minute. Turn
control knob to ON position. Adjust flame adjustment knob
anywhere between HI and LO. Slide the selector switch to the
REMOTE position (see Figure 52). Note: The burner may light
if hand-held remote was on when selector switch was last turned
off. You can now turn the burner on and off with the hand-held
remote control unit.
IH
PILOT
ON
Piezo
Ignitor
2.
3.
4.
Remove glass door (see Removing/Replacing Glass Door,
page 21).
Follow steps 1 through 8 under Lighting Instructions, page 24.
Depress gas control knob and light pilot with match.
Keep gas control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release gas control knob. Follow
steps 10 through 12 under Lighting Instructions,.
Replace glass door (see Removing/Replacing Glass Door,
page 21).
FF PIL
Gas Control
Knob
1.
Gas Control Knob
in ON Position
Figure 52 - Setting the Selector Switch, Gas Control Knob and
Variable Control Knob for Remote Operation
www.desatech.com
26
OPERATING FIREPLACE
Optional Hand-Held Remote Operation (Cont.)
Operating Optional GWMT1 Wall Mounted Thermostat
OPERATING FIREPLACE
Continued
safety feature to prevent accidental ignition of the fireplace, the receiver ON/OFF/REMOTE switch should be in the OFF position.
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
Auto Shutoff Feature
1. If the average room temperature exceeds 82 degrees
Fahrenheit (28 degrees Centigrade), the hand-held remote
control will perform a safety override and shut the fireplace
off. This feature is not available in the MANU mode.
2. The receiver continuously receives signals from the handheld remote to control the room temperature. If the handheld remote is misplaced, obstructed or for any reason
cannot transmit to the receiver, the receiver will shut off
the fireplace after 8 minutes.
TO UNLOCK press both buttons together on hand-held remote
Key Pad Lock Feature
ON/OFF SERIES
(Model GHRCB and CGHRCB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 53).
TO LOCK press both buttons on hand-held remote control until
control until the light stops flashing. The hand-held remote is
Control Button
Turns Burners
On and Off
Figure 53 - On/Off Hand-Held Remote Control Unit GHRCB
now unlocked.
THERMOSTAT SERIES
(Model GHRCTB and CGHRCTB)
The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 54). To
select Fahrenheit/Centigrade mode display, carefully press the ˚C/˚F
mode button with the end of a paper clip or similar blunt object.
Manual Mode
1.
2.
3.
Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
Press the MANU button to turn on the fireplace.
Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
+ or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the fireplace.
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
1.
Safety Features
This feature allows the user to lock/unlock the keypad on the handheld remote in the MANU or AUTO mode to prevent inadvertent
operation (i.e. children operating the hand-held remote control,
Digital Display
Shows
Temperature and
Settings
Turns Hand-Held
Remote On or Off and
Allows You to Choose
the Manual Setting
Turns Burners
On or Off
Selects Auto Setting
Decreases Room
Temperature in
AUTO Mode
Increases Room
Temperature in AUTO
Mode
Locks System to
Prevent Accidental
Ignition
Figure 54 - Thermostat Hand-Held Remote Control Unit
GHRCTB
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
WARNING: Do not connect the thermostat to a
power source. Electrical shock and/or a fire hazard
will occur.
Light the fireplace as instructed in Lighting Instructions on page
24. Set wall thermostat to desired temperature.
This thermostat has been electronically calibrated at the factory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize
at room temperature for a minimum of 30 minutes for proper
operation.
To turn the fireplace off, adjust thermostat to the lowest setting
and turn the gas control knob back to PILOT. The pilot will
remain lit.
IMPORTANT: To turn the pilot off, turn the gas control knob
on the heater to the OFF position.
When away from home for an extended period of time or as a child
www.desatech.com
116646-01A
OPERATING FIREPLACE
Operating Optional GWMT1 Wall Mounted Thermostat
Operating Optional Blower Accessory
27
27
INSPECTING BURNERS
Pilot Assembly
Burner Flame Pattern
OPERATING FIREPLACE
INSPECTING BURNERS
Continued
Check pilot flame pattern and burner flame patterns often.
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
WARNING: Do not connect the thermostat to a
power source. Electrical shock and/or a fire hazard
will occur.
Light the fireplace as instructed in Lighting Instructions on
page 24. Set wall thermostat to desired temperature.
This thermostat has been electronically calibrated at the factory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize
at room temperature for a minimum of 30 minutes for proper
operation.
To turn the fireplace off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot
will remain lit.
PILOT ASSEMBLY
The pilot assembly is factory preset for the proper flame height.
Alterations may have occurred during shipping and handling. Call
a qualified service person to readjust the pilot if necessary.
The height of the thermopile must be 3/8" to 1/2" above the pilot
flame as shown in Figure 55. The thermocouple must be at a height
of about 1/8" above the pilot flame. The flame from the pilot burner
must extend beyond both the thermocouple and thermopile.
If you pilot assembly does not meet these requirements:
• turn fireplace off (see To Turn Off Gas to Appliance, page 25)
• see Troubleshooting, page 29
3/8" to 1/2"
Pilot Burner
Thermopile
IMPORTANT: To turn the pilot off, turn the gas control knob
on the heater to the OFF position.
Thermocouple
OPERATING OPTIONAL
BLOWER ACCESSORY
Piezo
Ignitor
Locate the blower controls by opening the lower louver panel
on the fireplace. Blower controls are located on the right side of
the switch bracket to the left just inside the louver panel.
The BK manual blower and the BKT thermostatically-controlled
blower have an ON setting and an OFF setting. The blower
will only run when the switch is in the ON position. In the OFF
position, the blower will not operate.
Note for BKT Only: If you are using BKT blower with optional
thermostat (wall mounted or remote control) for the fireplace,
your fireplace and blower will not turn on and off at the same
time. The fireplace may run for several minutes before the blower
turns on. After the heater modulates to the pilot position, the
blower will continue to run. The blower will shut off after the
firebox temperature decreases.
Figure 55 - Pilot Assembly
BURNER FLAME PATTERN
Burner flames will be steady; not lifting or floating. Flame patterns
will be different from unit to unit and will vary depending on installation type and weather conditions.
If the vent configuration is installed incorrectly, the flames will lift
or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.
Figure 56 shows a typical flame pattern.
If burner flame pattern differs from that described:
• turn fireplace off (see To Turn Off Gas to Appliance, page 25)
• see Troubleshooting, page 29
The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust,
dirt or other obstructions that will hinder the flow of air.
Figure 56 - Typical Flame Pattern
116646-01A
1/8"
www.desatech.com
28
CLEANING AND MAINTENANCE
Glass Door
Pilot and Burners
Logs
Venting System
CLEANING AND MAINTENANCE
WARNING: Turn off fireplace and let cool before
cleaning.
CAUTION: You must keep control areas, burners and
circulating air passageways of fireplace clean. Inspect
these areas of fireplace before each use. Have fireplace
inspected yearly by a qualified service person. Fireplace
may need more frequent cleaning due to excessive lint
from carpeting, bedding material, pet hair, etc.
GLASS DOOR
WARNING: Handle glass door panel with care. Do
not strike, slam or otherwise abuse glass. Do not operate fireplace with the glass door unlatched removed,
cracked or broken.
WARNING: Do not use abrasive cleaners as this
may damage glass. Use a nonabrasive household glass
cleaner to clean glass. Do not clean glass when hot.
Glass must be cleaned periodically. During start-up it is normal for
condensation to form on the inside of the glass causing lint, dust and
other airborne particles to cling to the glass surface. During initial
start-up a slight film may form on the glass due to paint curing.
The glass should be cleaned several times with a non-ammonia,
nonabrasive household cleaner and warm water after the first two
weeks of operation. Thereafter, clean the glass two or three times
during each heating season, depending on the usage and circumstances present. Refer to Removing/Replacing Glass Door, page 21
of this manual when removing glass door for cleaning.
WARNING: Only parts supplied by the manufacturer should be used when replacing broken or
damaged glass door panel (see Replacement Parts,
page 31). This glass door panel is a complete unit.
No substitute materials may be used.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove
if glass is hot. Keep children and pets away from
glass.
Use only the tempered glass door replacement intended for this
fireplace (see Replacement Parts, page 34 for detail on ordering).
No substitutions may be made. See Removing/Replacing Glass
Door, page 21 for instructions for replacing glass door.
WARNING: Do not operate fireplace with the glass
door unlatched, removed, cracked or broken.
PILOT AND BURNERS
• Remove ember material before cleaning burners and replace
when cleaning is complete.
• Burner and controls should be cleaned with compressed air to
remove dust, dirt or lint.
• Use a vacuum cleaner or small, soft bristled brush to remove
excess dust, dirt or lint.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, Lava
Rock and Glowing Embers, page 23, to properly replace logs.
• Use a vacuum cleaner to remove any carbon buildup on logs.
• Replace log(s) if broken. See Replacement Parts on page 34.
• Replace ember material periodically as needed. See Replacement
Parts on page 34.
VENTING SYSTEM
Conduct annual inspection of the venting system following these
guidelines:
1. Check areas of venting system that are exposed to the weather for
corrosion (rust spots or streaks and, in extreme cases, holes). Have
these items replaced immediately by a qualified service person.
2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.
3. Check for evidence of excessive condensation. Continuous
condensation can cause corrosion of caps, pipes and fittings
and can be caused by having excessive lateral runs, too many
elbows or exterior portions of the system being exposed to cold
weather.
4. Inspect joints to verify that no pipe section or fitting has been
disturbed and loosened. Check mechanical supports such as wall
straps for rigidity.
If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, page 21). Vacuum all glass pieces with
a shop vac.
CAUTION: Do not vacuum if pieces are hot.
www.desatech.com
116646-01A
TROUBLESHOOTING
29
29
TROUBLESHOOTING
WARNING: Turn off heater and let cool before
servicing. Only a qualified service person should
service and repair heater.
CAUTION: Never use a wire, needle or similar
object to clean pilot. This can damage pilot unit.
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to ignitor
cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3. Piezo ignitor nut is loose
4.
5.
6.
7.
When ignitor button is pressed, there is spark
at pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Gas control knob not in PILOT position
3. Gas control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
5. Depleted gas supply (propane/LP models
only)
6. Pilot is clogged
7. Gas regulator setting is not correct
Pilot lights but flame goes out when control
knob is released
116646-01A
1. Gas control knob not fully pressed in
2. Gas control knob not pressed in long
enough
3. Equipment shutoff valve not fully
open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
www.desatech.com
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor. Nut is
located behind the mounting bracket
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace pilot assembly
7. Tighten electrode. Replace if necessary
1. Turn on gas supply or open equipment
shutoff valve
2. Turn gas control knob to PILOT position
3. Press in gas control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is
removed
5. Contact local propane/LP gas company
6. Clean pilot (see Cleaning and Maintenance,
page 28) or replace pilot assembly
7. Replace gas regulator
1. Press in gas control knob fully
2. After pilot lights, keep gas control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural or propane/LP
gas company
B) Clean pilot (see Cleaning and
Maintenance, page 28) or replace pilot
assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace pilot assembly
7. Replace control valve
TROUBLESHOOTING
30
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Contact local propane/LP or natural gas
company
3. Reconnect leads
2. Inlet gas pressure is too low
3. Thermopile leads disconnected or improperly connected
4. Thermopile is defective
Delayed ignition burner
1. Manifold pressure is too low
2. Burner porting or orifice clogged
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
4. Replace thermopile
1. Contact local propane/LP or natural gas
company
2. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Damaged burner
3. Gas regulator defective
1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
Slight smoke or odor during initial operation
1. Residues from manufacturing processes
and logs curing
1. Problem will stop after a few hours of
operation
Heater produces a whistling noise when
burner is lit
1. Turning gas control knob to HI position
when burner is cold
2. Air in gas line
1. Turn gas control knob to LO position
and let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local
propane/LP or natural gas company
3. Clean burner (see Cleaning and Maintenance, page 27) or replace burner
orifice
3. Dirty or partially clogged burner orifice
Glass soots
1. Flame inmpingement on logs
2. Debris around burner air mixer
1. Adjust log set so that the flame does not
excessively impinge in it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
Fireplace produces a clicking/ticking noise
just after burners are lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common. If noise is excessive,
contact qualified service person
Remote does not function
1. Battery is not installed or battery power
is low
1. Replace 9-volt batteries in receiver and
remote control
www.desatech.com
116646-01A
TROUBLESHOOTING
31
31
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
•
•
•
•
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Fireplace produces unwanted odors
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, page 19)
Fireplace shuts off in use
1. High or gusting winds
1. Fireplace has been tested for up to
40mph winds. However, extreme conditions may occur. See Lighting Instructions on page 24
2. Contact local propane/LP or natural gas
company
3. Clean pilot (see Cleaning and Maintenance, page 28)
4. Locate and correct all leaks (see Checking Gas Connections, page 19)
5. Tighten glass
2. Low line pressure
3. Pilot is partially clogged
4. Inner vent pipe leaking exhaust gasses
into system
5. Glass too loose and air tight gasket leaks
in corners after usage
6. Bad thermopile or thermocouple
7. Improper vent cap installation
6. Replace faulty component
7. Check for proper installation and freedom from debris or blockage
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement
above
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, page 19)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, page 19)
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing
Logs, Lava Rock anc Glowing Embers,
page 23)
2. Clean out air holes at burner inlets. Periodically repeat as needed
3. Remove blockage or replace burner
4. Have the vent system inspected, including the termination cap. Remove any
restrictions or obstruction
5. Clear excess embers until a minimum
gap of 1/2" remains under the grate
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
4. Improper venting or excessive blockage
5. Excessive amounts of embers and pan
material
116646-01A
www.desatech.com
32
ILLUSTRATED PARTS BREAKDOWN
(V)T32N-A, (V)T32NB-A, (V)T32NR-A, (V)T32NRB-A
(V)T32P-A, (V)T32PB-A, (V)T32PR-A, (V)T32PRB-A, CGDV32NR
ILLUSTRATED PARTS
BREAKDOWN
(V)T32N-A, (V)T32NB-A
(V)T32NR-A
(V)T32NRB-A
(V)T32P-A, (V)T32PB-A
(V)T32PR-A
22-1
(V)T32PRB-A
CGDV32NR
22-3
6
22-4
22-5
22-6
7
22-2
8
4
1
12
14
9
3
17
21
19
15
11
20
10
18
9-17
9-19
13
16
9-16
9-15
9-1
9-2
2
9-8
16
9-13
9-3
9-7
9-18
5
9-9
9-14
9-6
9-12
9-4
9-11
9-5
9-10
www.desatech.com
116646-01A
PARTS LIST
(V)T32N-A, (V)T32NB-A, (V)T32NR-A, (V)T32NRB-A
(V)T32P-A, (V)T32PB-A, (V)T32PR-A, (V)T32PRB-A, CGDV32NR
33
33
PARTS LIST
(V)T32N-A, (V)T32NB-A, (V)T32NR-A, (V)T32NRB-A, (V)T32P-A, (V)T32PB-A, (V)T32PR-A,
(V)T32PRB-A, CGDV32NR
This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts
on page 34 of this manual.
KEY PART
NO. NUMBER
1
2
3
4
**
**
108892-01
108892-02
109155-01
108903-01
5
109155-02
108903-02
6
7
8
9
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
9-14
**
**
**
108885-01
108885-02
11102
11105
11179
11237
14389
14390
14492
14500
14253
14511
14528
104506-25
14514
104509-02
26808
26827
KEY PART
QTY. NO. NUMBER
DESCRIPTION
Firebox Assembly
Face Weldment
Door Assembly (T & CGDV Models Only)
Door Assembly (VT Models Only)
Top Stamped Panel Assy
T32N/P, T32NB/PB Models
Top Rolled Louver Assy T32NR/PR,
T32NRB/PRB & CHDV32NR Models
Bottom Stamped Panel Assy
T32N/P, T32NB/PB Models
Bottom Rolled Louver Assy (T32NR/PR,
T32NRB/PRB, CHDV32NR Models)
Fireplace Top
Fireplace Top Insulation
Fireplace Surround
Burner Assembly (Natural)
Burner Assembly (Propane/LP)
Screw #8-32 x 3/8 PPH Zinc
Screw #10 x 1/2 Zinc
Screw #10-24 x 1/4 Zinc
Screw, Trilab M4 x 8mm
Millivolt Valve (Natural)
Millivolt Valve (Propane/LP)
Piezo Ignitor
Brass Fitting
Flexible Connector
Ignitor Bracket
Brass Elbow Fitting
Orifice (Natural #47)
Orifice (Propane/LP #55)
Aluminum Tubing Assy
Valve Bracket
Switch Bracket
1
1
1
1
1
1
9-15 108886-01
9-16 108891-01
9-17 108084-02
108084-03
9-18 108889-01
9-19 27113
10
108890-01
11
108897-01
1
1
1
1
1
1
1
2
9
4
1
1
1
1
2
1
1
1
1
1
1
1
1
12
13
109082-03
108901-01
14
108901-02
15
16
17
18
19
20
21
22
22-1
22-2
22-3
22-4
22-5
22-6
11418
108440-01
109479-01
14123
21171
24353
24460
109222-01
109403-01
109404-01
109407-01
109406-01
109405-01
109408-01
Base Grate Assembly
Burner
Pilot Assembly (Natural)
Pilot Assembly (Propane/LP)
Burner Base Assembly
Air Deflector
Burner Base Gasket
Rear Refractory Brick Panel
(B Models Only)
Heat Shield
Right Refractory Brick Panel
(B Models Only)
Left Refractory Brick Panel
(B Models Only)
Push-On Nut
Screen
Screen Rod
Strain Relief
Gas Knock-Out Cover
Handy Box Assembly
Gas Conduit Assembly
Log Set
Front Log (Log 1)
Rear Log (Log 2)
Base Log (Log 3)
Crossover Log (Log 4)
Left Top Log (Log 5)
Right Top Log (Log 6)
QTY.
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
25487
PCDM-32T
** Not a field replaceable part.
116646-01A
DESCRIPTION
www.desatech.com
Lava Rock/Bag Assy
Conversion Kit (CGDV32NR only)
1
1
34
REPLACEMENT PARTS
SPECIFICATIONS
SERVICE HINTS
TECHNICAL SERVICE
REPLACEMENT PARTS
SERVICE HINTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
When Gas Pressure Is Too Low
PARTS UNDER WARRANTY
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESAʼs Customer Service Department at 1-866-672-6040.
When calling DESA, have ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
•
•
•
•
pilot will not stay lit
burners will have delayed ignition
fireplace will not produce specified heat
propane/LP gas supply might be low (propane/LP units only)
You may feel your gas pressure is too low. If so, contact your local
gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation or
troubleshooting. If so, contact DESAʼs Customer Service Department at 1-866-672-6040. When calling, please have your model
and serial numbers of your heater ready.
You can also visit DESAʼs technical service web site at
www.desatech.com.
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESA at 1-866-672-6040 for
referral information.
When calling DESA, have ready
• model number of your fireplace
• the replacement part number
SPECIFICATIONS
CGDV32NR
(V)T32N(R)-A
(V)T32P(R)-A
12,000/18,000 Btu/hr
11,000/17,000 Btu/hr
Natural
Propane/LP
Piezo
Piezo
Manifold Pressure
3.5" w.c.
10.0" w.c.
Minimum Inlet Supply Pressure
5.5" w.c.
11.0" w.c.
32 1/4" x 34 1/2" x 16 5/8"
819 x 876 x 422 mm
32 1/4" x 34 1/2" x 16 5/8"
819 x 876 x 422 mm
33 1/2" x 37 1/2" x 17 1/2"
851 x 953 x 445 mm
33 1/2" x 37 1/2" x 17 1/2"
851 x 953 x 445 mm
Fireplace
80 lbs/36 kg
80 lbs/36 kg
Shipping
83 lbs/38 kg
83 lbs/38 kg
Btu
Gas Type
Ignition
Dimension (H x W x D) Fireplace
(Actual size of firebox.
Measurements do not include
nailing flanges or standoffs).
Carton
Weight, lbs/kg*
*For refractory lined models add 45 pounds.
www.desatech.com
116646-01A
35
35
OWNER'S REGISTRATION FORM
In order to provide better customer service for this and future purchases, we recommend that you register your product with us.
You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner's
Registration Form and mail to the address on the back of this owner's manual. Please provide the following product information:
Brand:
(Comfort Glow, Vanguard, etc.)
Model:
(EFP33PR, VTGH33NR, etc.)
Date Purchased:
Note: Keep receipt for warranty verification.
Serial Number:
7 or 9 digit number located on product or identification tag.
First Name:
Last Name:
Address:
City:
Home Phone:
State:
(
)
Zip:
Country:
-
E-Mail:
Please answer the following questions to register your product with DESA:
1.
Where will the product be used?
� Living/Family Room
� Office/Warehouse
� Utility Shed/Outbuilding
� Garage
� Bedroom
� Bathroom
2.
If you bought this product yourself, did you plan to purchase this type of product before going into the store?
3.
Who selected the product? � Male � Female � Both
4.
What is the population of your area? � Under 10,000
� 100,000 to 250,000
� 10,000 to 25,000
What is your primary source of heat?
6.
How was the product installed? � Professional Installer
7.
Cost of product excluding sales tax? $___________________
8.
Cost to install product? $____________________
� Propane (LP Gas)
� Farm Store
� Fuel Oil
� Self
Type of store where product was purchased? � Hardware
� Fireplace or Hearth Shop
� Emergency Back-Up Heat
� Propane Dealer
12. Level of Education of Purchaser: � Some High School
� 30 - 39
� $75,000 to $99,999
� Replace Older Model
� Relative or Friend
� 40 - 49
� 50 - 59
� D.I.Y. Home Project
� Completed College
� $15,000 to $19,999
� $20,000 to $34,999
� $100,000 and Over
Name: ______________________________________
City: _______________________ State: __________
16. In choosing this product, how important were the following:
Not Important
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
� Other
� Other ________________________
� Completed Graduate School
� 60 or Over
15. Store where product was purchased:
Heat Output
Made in USA
Warranty
Local Service
Value for Price
Prior Brand Experience
Controls Location
Thermostat, Remote, or Manual Operation
Ease of Operation
Special Features
Salesperson's Recommendation
Friend/Relative's Recommendation
116646-01A
Portability
Quiet Operation
� Other
� Home Center/Builder's Supply
� Construction Project
� Store Display
� Completed High School
14. Buyer's total annual household income: � Under $15,000
Availability
Price
Brand Name
Overall Quality
� Electric
� Natural Gas/Utility Co.
� Energy Savings/High Efficiency
11. How did you learn about this product brand? � Advertising
� 20 - 29
� Natural Gas
� Other
� Heater was on Sale
13. Age of Purchaser: � Under 20
� Wood
� Other
10. What motivated you to buy this product? � Sudden Cold Weather
� $50,000 to $74,999
� 50,000 to 100,000
� Over 250,000
5.
9.
� 25,000 to 50,000
� Other
� Yes � No
Somewhat Important
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
www.desatech.com
�
�
Very Important
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
� $35,000 to $49,999
TAPE
36
Postage
Required
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
TAPE
116646-01A
ACCESSORIES
37
37
ACCESSORIES
NOTICE: All accessories may not be available for all
fireplace models.
Purchase these fireplace accessories from your local retailer. If they
can not supply these accessories, call DESAʼs Sales Department at
1-866-672-6040. for information. You can also write to the address
listed on the back page of this manual.
BRICK LINER
(Not Shown)
THERMOSTATICALLY- CONTROLLED
BLOWER KIT - BKT
Provides better heat distribution. Blower turns off and on automatically, as needed. Complete installation and operation instructions
included in this manual.
BL32D - Refractory Brick Liner Kit
This brick liner adds a touch of style to your direct-vent fireplace.
Complete installation instructions included in this manual.
FLEXIBLE GAS LINE CONNECTOR - GA5081
(Not Shown)
For all models.
PROPANE/NATURAL GAS CONVERSION KIT
(Not Shown)
RECEIVER AND HAND-HELD THERMOSTAT
REMOTE CONTROL KIT - GHRCTB AND
CGHRCTB
For all Remote-Ready Models. Allows the fireplace to be operated
in a manually or thermostatically-controlled mode. You can adjust
your heat settings and turn the fireplace on or off without leaving the
comfort of your easy chair.
PCDM-32T - Propane/LP Gas Conversion Kit
NCDM-32T - Natural Gas Conversion Kit
FACE/LOUVER PANEL KIT
(Not Shown)
RLD32 - Rolled Louver Panels - Black
LOUVER TRIM KIT (Rolled Louvers Only)
(Not Shown)
LT32B - Rolled Louver Trim Kit - Brushed Brass
LT32P - Rolled Louver Trim Kit - Platinum
LT32PB - Rolled Louver Trim Kit - Polished Brass
DEFLECTION HOODS
(Not Shown)
HD32 - Hood - Black (2" Brow)
PERIMETER TRIM KIT
(Not Shown)
PT32 - Perimeter Trim Kit - Black
PT32B - Perimeter Trim Kit - Brushed Brass
PT32P - Perimeter Trim Kit - Platinum
PT32PB - Perimeter Trim Kit - Polished Brass
RECEIVER AND HAND-HELD ON/OFF REMOTE
CONTROL KIT - GHRCB AND CGHRCB
For all Remote-Ready Models. Allows the fireplace to be turned
on and off conveniently.
WALL MOUNTED THERMOSTAT CONTROL
KIT - GWMT1 (Not Shown)
Allows easy wall access for thermostatic operation of your fireplace.
WALL MOUNTED ON/OFF SWITCH - GWMS2
(Not Shown)
Allows burner system to be turned on and off with a wall switch.
MANUAL BLOWER KIT - BK
Manual variable control blower accessory
provides better heat distribution. Complete
installation and operation instructions included in this manual.
116646-01A
www.desatech.com
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
LIMITED WARRANTY
DIRECT-VENT FIREPLACE
DESA warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase, provided that the
product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty
the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating
condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized
retailers of this product and/or DESA who will provide original factory replacement parts. Failure to use original factory replacement parts voids this
warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts that fail or become damaged as
a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation
and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESAʼS LIABILITY IS HEREBY LIMITED
TO THE PURCHASE PRICE OF THE PRODUCT AND DESA SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER
INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
116646 01
NOT A UPC
116646-01
Rev. A
03/05
Download PDF

advertising