Installation manual | Desa Tech SL30PT Gas Heater User Manual

(VENT-FREE) PROPANE/LP GAS
STOVE HEATER
OWNER’S OPERATION AND INSTALLATION MANUAL
Model SL30PT Series Thermostat Control Gas Log Heater
(Burner System For Cast Iron Stoves)
SL30PT
Patent Pending
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury, or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your
building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
WARNING: The SL30PT series vent-free gas
log heater is only approved for use in the
Comfort Glow series cast iron stove models
CISC and CISG.
WARNING: Improper installation, adjustment, alteration, service, or maintenance
can cause injury or property damage.
Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency,
or the gas supplier.
WARNING: This is an unvented gas-fired
heater. It uses air (oxygen) from the room
in which it is installed. Provisions for
adequate combustion and ventilation air
must be provided. Refer to Air for Combustion and Ventilation section on page
4 of this manual.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
VENT-FREE PROPANE/LP GAS STOVE HEATER
SAFETY
INFORMATION
WARNING ICON
G 001
Due to high temperatures, the
appliance should be located out
of traffic and away from furniture
and draperies.
WARNINGS
Stove becomes very hot when
running heater. Keep children and
adults away from hot surface to
avoid burns or clothing ignition.
Heater will remain hot for a time
after shutdown. Allow surface to
cool before touching.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning: Early signs
Carefully supervise young children when they are in the room
with fireplace.
Make certain you read and understand all
Warnings. Keep this manual for reference.
It is your guide to safe and proper operation
of this heater.
1.
2.
3.
WARNING: Any change to
this heater or its controls can be
dangerous.
WARNING: Do not allow fans
to blow directly into the stove.
Avoid any drafts that alter burner
flame patterns. Ceiling fans can
create drafts that alter burner
flame patterns. Altered burner
patterns can cause sooting.
WARNING: Do not use a
blower insert, heat exchanger
insert or other accessory not approved for use with this heater.
9.
10.
11.
Keep the appliance area clear and
free from combustible materials,
gasoline, and other flammable
vapors and liquids.
Propane/LP Gas: Propane/LP gas is odor-
less. An odor-making agent is added to the gas.
The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas
may be present even though no odor exists.
8.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate, or service this heater. Improper use of this heater can
cause serious injury or death from
burns, fire, explosion, electrical
shock, and carbon monoxide
poisoning.
of carbon monoxide poisoning resemble the
flu, with headaches, dizziness, or nausea. If
you have these signs, the heater may not be
working properly. Get fresh air at once!
Have heater serviced. Some people are more
affected by carbon monoxide than others. These
include pregnant women, people with heart or
lung disease or anemia, those under the influence of alcohol, and those at high altitudes.
7.
4.
5.
6.
This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases.
Do not place propane/LP supply tank(s)
inside any structure. Locate propane/
LP supply tank(s) outdoors.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do
not use any phone in your building
• immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions
• if you cannot reach your gas supplier,
call the fire department
This heater shall not be installed in a
bedroom or bathroom.
Do not place stove directly on carpeting, vinyl tile, or any combustible material other than wood. The stove must
set on a metal or wood panel extending
the full width and depth of the appliance.
Do not use this stove as a wood burning fireplace. Use only model SL30PT
vent-free gas log heater.
2
12.
13.
14.
15.
16.
17.
18.
Do not add extra logs or ornaments
such as pine cones, vermiculite, or rock
wool. Using these added items can
cause sooting.
This log heater is designed to be smokeless. If logs ever appear to smoke, turn
off heater and call a qualified service
person. Note: During initial operation,
slight smoking could occur due to log
curing and heater burning manufacturing residues.
To prevent the creation of soot, follow
the instructions in Cleaning and Maintenance, page 15.
Before using furniture polish, wax, carpet cleaners, or similar products, turn
heater off. If heated, the vapors from
these products may create a white powder residue within burner box or on
adjacent walls or furniture.
This heater needs fresh, outside air ventilation to run properly. This heater has
an Oxygen Depletion Sensing (ODS)
safety shutoff system. The ODS shuts
down the heater if not enough fresh air
is available. See Air for Combustion
and Ventilation, pages 4 through 6. If
heater keeps shutting off, see Troubleshooting, pages 16 through 18.
Do not run heater
• where flammable liquids or vapors
are used or stored
• under dusty conditions
Do not use this stove to cook food or
burn paper or other objects.
Do not use heater if any part has been
exposed to or under water. Immediately
call a qualified service technician to inspect the room heater and to replace any
part of the control system and any gas
control which has been under water.
Do not operate heater if any log is broken. Do not operate heater if a log is
chipped (dime-sized or larger).
Turn heater off and let cool before servicing. Only a qualified service person
should service and repair heater.
Operating heater above elevations of
4,500 feet could cause pilot outage.
To prevent performance problems, the
use of a propane/LP tank of less than
100 lb. capacity is not recommended.
104464
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
PRODUCT
FEATURES
OPERATION
Stove
Body
One Piece
Log Set
Inside Stove
Cavity
This heater is clean burning. It requires no
outside venting. There is no heat loss out a
vent or up a chimney. Heat is generated by
realistic, dancing yellow flames. This heater
is designed for vent-free operation. State
and local codes in some areas prohibit the
use of vent-free heaters.
SAFETY PILOT
This heater has a pilot with an Oxygen
Depletion Sening (ODS)safety shutoff system. The ODS/pilot is a required feature for
vent-free room heaters. The ODS/pilot shuts
off the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.
Piezo Ignitor
Stove Door
(Shown in the
open position)
Gas Log Heater
Base Assembly
Control Knob
Figure 1 - Typical Stove Cabinet Model with Comfort Glow Gas Log Heater
LOCAL CODES
Install and use heater with care. Follow all
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas
Code ANS Z223.1, also known as NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
104464
3
VENT-FREE PROPANE/LP GAS STOVE HEATER
AIR FOR
COMBUSTION AND
VENTILATION
WARNING: This heater shall
not be installed in a confined space
or unusually tight construction
unless provisions are provided
for adequate combustion and ventilation air. Read the following instructions to insure proper fresh
air for this and other fuel-burning
appliances in your home.
Today’s homes are built more energy efficient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home owners
weather strip and caulk around windows and
doors to keep the cold air out and the warm air
in. During heating months, home owners
want their homes as airtight as possible.
While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide adequate fresh air for these appliances. This
will insure proper venting of vented fuelburning appliances.
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from National Fuel Gas Code, NFPA 54/ANS
Z223.1, Section 5.3, Air for Combustion
and Ventilation.
All spaces in homes fall into one of the three
following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will
help you classify your space and provide
adequate ventilation.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.
Confined and Unconfined Space
The National Fuel Gas Code ANS Z223.1
defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000
Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed
in that space and an unconfined space as a
space whose volume is not less than 50
cubic feet per 1,000 Btu per hour (4.8 m3 per
kw) of the aggregate input rating of all
appliances installed in that space. Rooms
communicating directly with the space in
which the appliances are installed*, through
openings not furnished with doors, are considered a part of the unconfined space.
This heater shall not be installed in a confined space or unusually tight construction
unless provisions are provided for adequate
combustion and ventilation air.
* Adjoining rooms are communicating only
if there are doorless passageways or ventilation grills between them.
Unusually tight construction is defined as construction where:
a. walls and ceilings exposed to the
outside atmosphere have a continuous water vapor retarder with
a rating of one perm (6 x 10-11 kg
per pa-sec-m2) or less with openings gasketed or sealed and
b. weather stripping has been
added on openable windows and
doors and
c. caulking or sealants are applied
to areas such as joints around
window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three
criteria above, you must provide additional fresh air. See Ventilation Air
From Outdoors, page 6.
If your home does not meet all of the
three criteria above, proceed to Determining Fresh-Air Flow For Heater
Location, page 5.
4
104464
OWNER’S MANUAL
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this work sheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between
the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = ____________________ cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
_________________ (volume of space) ÷ 50 cu. ft. = (maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
___________________ Btu/Hr
Gas water heater*
___________________ Btu/Hr
Example:
Gas furnace
___________________ Btu/Hr
Gas water heater
40,000
Btu/Hr
Vented gas heater
___________________ Btu/Hr
Vent-free heater + 30,000
Btu/Hr
Gas fireplace logs
___________________ Btu/Hr
Total
= 70,000
Btu/Hr
Other gas appliances* + ___________________ Btu/Hr
Total
= ___________________ Btu/Hr
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
70,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.
Continued
104464
5
VENT-FREE PROPANE/LP GAS STOVE HEATER
AIR FOR
COMBUSTION AND
VENTILATION
Continued
VENTILATION AIR
Ventilation Air From Inside
Building
12"
Ventilation
Grills
Into Adjoining
Room,
Option 1
This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must provide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel
Gas Code, NFPA 54/ANS Z223.1, Section
5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
WARNING: Rework worksheet, adding the space of the
adjoining unconfined space. The
combined spaces must have
enough fresh air to supply all
appliances in both spaces.
IMPORTANT: Do not provide openings
for inlet or outlet air into attic if attic has
a thermostat-controlled power vent.
Heated air entering the attic will activate
the power vent.
Or
Remove
Door into
Adjoining
Room,
Option
3
12"
Figure 2 - Ventilation Air from Inside Building
Outlet
Air
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two permanent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
or spaces open to the outdoors. These spaces
include attics and crawl spaces. Follow the
National Fuel Gas Code, NFPA 54/ANS
Z223.1, Section 5.3, Air for Combustion and
Ventilation for required size of ventilation
grills or ducts.
Ventilation Grills
Into Adjoining Room,
Option 2
Ventilated
Attic
Outlet
Air
To Attic
To
Crawl
Space
Inlet
Air
Inlet Air
Ventilated
Crawl Space
Figure 3 - Ventilation Air from Outdoors
6
104464
OWNER’S MANUAL
INSTALLATION
NOTICE: This heater is intended
for use as supplemental heat. Use
this heater along with your primary heating system. Do not install this heater as your primary
heat source. If you have a central
heating system, you may run
system’s circulating blower while
using heater. This will help circulate the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.
WARNING: A qualified service person must install heater.
Follow all local codes.
WARNING: Never install the
heater
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objects are less than 42 inches
from the front, top, or sides of
the heater
• in high traffic areas
• in windy or drafty areas
CAUTION: This heater creates warm air currents. These
currents move heat to wall surfaces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as tobacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
IMPORTANT: Vent-free heaters add moisture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Combustion and Ventilation, pages 4 through 6.
CHECK GAS TYPE
Use only propane/LP gas. If your gas supply
is not propane/LP gas, do not install heater.
Call dealer where you bought heater for
proper type heater.
CLEARANCES TO
COMBUSTIBLES
(Vent-Free Operation Only)
WARNING: Maintain the minimum clearances. If you can, provide greater clearances from
floor, ceiling, and adjoining side
and back walls.
Carefully follow the instructions below. This
stove is a freestanding unit designed to set
directly on the floor. IMPORTANT: You
must maintain minimum wall and ceiling
clearances during installation. The minimum clearances are shown in Figure 4.
Measure from outermost point of stove top.
Minimum Wall and Ceiling
Clearances (see Figure 4)
A. Clearances from outermost point of
stove top to any combustible side wall
should not be less than 12 inches.
B. Clearances from outermost point of
stove top to any combustible back wall
should not be less than 6 inches (Includes Corner Installations).
C. Clearances from the stove top to the
ceiling should not be less than 48
inches.
Ceiling
Front View
48"
Minimum
Side Wall
12"
Minimum
12"
Minimum
Side Wall
Top View
Back Wall
6"
Minimum
Side View
Ceiling
12 "
Minimum
12 "
Minimum
Side Wall
Side Wall
48"
Minimum
Corner
Wall
Back Wall
6"
Minimum
Wall
6"
Minimum
Front of
Stove Unit
6"
Minimum
Floor
Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on
Model)
Continued
104464
7
VENT-FREE PROPANE/LP GAS STOVE HEATER
INSTALLATION
Continued
Bolt
STOVE CAVITY ASSEMBLY
1.
2.
3.
4.
5.
6.
7.
8.
Lift off corrugated box enclosing stove
body crating.
Remove all screws fastening the wood
frame enclosure. Spread wood frame
open and lift away from plastic-bagged
stove body. The bottom pieces of pallet wood will remain bolted to the stove
body.
Remove plastic bag from stove body.
Remove back panel from stove (see
Figure 5). Use an adjustable wrench or
a 10 mm socket. Remove six (6) bolts
and washers. Keep bolts and washers
to reattach back panel later.
Remove all contents from inside stove
cavity. Contents include:
(1) - Stove bottom
(4) - Legs (Amity models include leg
leveler bolts)
(1) - Bottom door
(1) - Top grate
(1) - Hardware kit bag with fasteners
Carefully lay stove body on back to
attach bottom components to stove
body (see Figure 6). Rest stove on drop
cloth or blanket to avoid scratching
stove edges.
Remove remaining pallet wood attached to bottom of stove body (see
Figure 7). Use an adjustable wrench to
remove bolts.
Fasten each leg to stove with four (4)
bolts. Use a flat screw driver to tighten
bolt to leg. Thread bolt in tapped holes
on stove body (see Figure 8 and Figure
9, page 9).
Product
Back Stove Panel
Identification Label
Figure 5 - Removing Back Panel
Top of Stove Unit
Front of
Stove Unit
Top of
Stove
Unit
Front of
Stove Unit
Pallet Wood
Bolted to
Stove Body
Bottom
Drop Cloth/
Blanket
Figure 6 - Laying Down Stove On Side (Stove Style May Vary Depending on Model)
Front
Pallet
Wood
Bolt
Bottom Of
Stove Unit
Pallet
Wood
Figure 7 - Removing Pallet Wood From The Bottom of The Stove
Door Hinge Step
Bolt Hole
Front
Leg
Hole
Door Catch Bolt
With Adjustable
Hex Nuts Hole
Leg
Hole
Stove
Bottom
Holes
Leg
Hole
Bottom Of
Stove Unit
Leg
Hole
Figure 8 - Locating Threaded Holes for Stove Bottom, Legs, and Door Attachment
(Appearance May Vary Depending on Model)
8
104464
OWNER’S MANUAL
INSTALLATION
Continued
9.
10.
11.
12.
13.
14.
15.
Fasten stove bottom to stove with four
(4) M6 x 1 - 25mm bolts. Use a flat
washer and lock washer with each bolt.
Tighten bolts into threaded holes on
stove body (see Figure 8, page 8 and
10). Use an adjustable wrench or a
10mm socket.
Attach stove door by inserting step bolt
through door hinge pivot holes and into
threaded hole in stove body (see Figure 11). Use an adjustable wrench or a
12mm socket to fasten step bolt.
Tighten step bolt until snug. Make sure
door moves freely.
Install door catch bolt (M8 x 1.2555mm with two M8 hex nuts) into
threaded hole on stove body (see Figure 8, page 8). Use an adjustable
wrench or a 12mm socket. The catch
bolt has two hex nuts attached to it (see
Figure 12). The top nut is a bolt stop
and the bottom nut is for door leveling
adjustment.
Check general catch bolt alignment
with door claw. Make final adjustment
and door leveling after stove is in normal standing position.
Carefully lift stove back up on its four
attached legs.
If available, install gas log heater inside stove cavity before installing the
back panel (see Installing Gas Log
Heater Into Stove, page 10).
Fasten back panel to stove with six (6)
M6 x 1 - 20mm bolts and washers.
Make sure product identification label
is located on the outside in lower lefthand corner.
Washers
Bolt
Bottom Of
Stove Unit
Bolt
Leg
Bottom Of
Stove Unit
Figure 9 - Attaching Stove Legs
Stove
Bottom
Figure 10 - Attaching Stove Bottom
Stove
Door
Stove
Door
Bolt
Shoulder
Threaded
Hole
Door
Hinge
Door
Hinge
Step
Bolt
Step
Bolt
Bolt
Stove Bottom
Shoulder
Figure 11 - Attaching Stove Door (Appearance May Vary Depending on Model)
Bolt Stop
Adjusting Nut
Door
Door Claw
Catch Bolt
Figure 12 - Catch Bolt and Door Claw Orientation
Continued
104464
9
VENT-FREE PROPANE/LP GAS STOVE HEATER
2.
3.
4.
5.
6.
Remove log and gas log heater from
carton. Note: Do not pick up gas log
heater by the burner itself. This could
damage heater. Always handle the gas
log heater by the heater base only.
Remove all protective packaging applied
to log and gas log heater for shipment.
Check all items for any shipping damage. If damaged, promptly inform
dealer where you bought heater.
If not already removed, remove back
panel from assembled stove body (see
Figure 5, page 8). Use an adjustable
wrench or a 10 mm socket. Remove six
(6) bolts and washers. Keep bolts and
washers to reattach back panel later.
Set gas log heater inside stove (see Figure 13). Make sure control knob extensions pass through bottom front opening.
Align outside holes on heater base with
four (4) mounting holes on the stove
bottom (see Figure 13).
Burner
Bolt
Stove
Bottom
Hex Nut
Figure 14 - Fastening Heater Base to
Stove Drop Bottom
One-Piece
Log Set
Middle
Section at
Bottom of
Log Set
Burner
LO
Heater
Base
OT
1.
Heater
Base
PIL
INSTALLING GAS LOG
HEATER INTO STOVE
Fasten heater base to stove bottom with
#10-24 x .50 bolts and hex nuts provided with gas log heater (see Figure
14). Attachment hardware is factory
packed inside plastic bag with installation manual and owner’s registration
card. Push bolt through heater base
mounting hole and through stove bottom. Connect hex nut to bolt on underside of stove bottom. The bolt hex head
is for a 5/16" socket and the hex nuts
are for a 3/8" socket. If sockets are not
available, use adjustable wrenches.
8. Set one-piece log on heater base as
shown in Figure 15. Make sure middle
section at bottom of log is seated into
"U" shaped cutout in center of heater
base. Log will fit securely on base.
IMPORTANT: Make sure log does not
cover any burner ports and does not
touch the stove cavity (see Figure 16).
9. Fasten back panel to stove with six (6)
M6 x 1.20mm bolts and washers. Make
sure product identification label is located
on the outside lower left-hand corner.
10. Place freestanding stove in desired position in room. Be sure to maintain
clearances to combustibles as outlined
on page 7.
F
HI
Continued
7.
OF
INSTALLATION
"U" Shaped
Cutout in
Chassis
Figure 15 - Installing One-Piece Stove
Log Set
Bottom
Front
Opening
Burner Porting Areas
(double slotted
rectangular openings
Bolt
Heater
Base
Stove
Bottom
Figure 13 - Placing Heater Base In Stove Cavity (Appearance May Vary Depending on
Model)
Safety Pilot Location
One-Piece
Log Set
Figure 16 - Top View of One-Piece Log
Set on Gas Log Heater
10
104464
OWNER’S MANUAL
INSTALLATION
Continued
CONNECTING TO GAS
SUPPLY
WARNING: This appliance requires a 1/2" NPT (National Pipe
Thread) inlet connection to the
pressure regulator.
WARNING: A qualified service
person must connect heater to gas
supply. Follow all local codes.
CAUTION: Never connect
heater directly to the propane/LP
supply. This heater requires an external regulator (not supplied). Install the external regulator between
the heater and propane/LP supply.
Installation Items Needed
Before installing heater, make sure you have
the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
* An CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an
acceptable alternative to test gauge connection. Purchase the optional CSA/AGA design-certified equipment shutoff valve from
your dealer. See Accessories, page 19.
From External
Regulator (11"
W.C.** to 14" W.C.
Pressure)
Tee Joint
Pipe
Nipple
Cap
Figure 19 - Gas Connection
The gas inlet connection for the stove heater
is located on the lower right-hand side of the
stove when viewed from the front of the
unit. The gas connection can be made either
through the bottom right side or through the
lower back opening as illustrated in Figure
17. Make sure gas log heater is secured to
the stove cavity assembly.
The installer must supply an external regulator. The external regulator will reduce
incoming gas pressure. You must reduce
incoming gas pressure to between 11 and 14
inches of water. If you do not reduce incoming gas pressure, heater regulator damage
could occur. Install external regulator with
the vent pointing down as shown in Figure
18. Pointing the vent down protects it from
freezing rain or sleet.
Back Stove
Panel
Product
Identification
Label
Back View
Gas
Log
Heater
Side View
Front
of
Stove
Unit
Gas Inlet
Connection
Access
WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly
known as wellhead gas.
CAUTION: Use only new,
black iron or steel pipe. Internally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of 1/2"
diameter or greater to allow
proper gas volume to heater. If
pipe is too small, undue loss of
pressure will occur.
Installation must include a equipment shutoff
valve, union, and plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from
heater (see Figure 19).
IMPORTANT: Install equipment shutoff
valve in an accessible location. The equipment shutoff valve is for turning on or
shutting off the gas to the appliance.
Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged heater valves.
CAUTION: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.
External
Regulator
Figure 17 - Gas Regulator Location and
Gas Line Access Into Stove Cabinet
Propane/LP
Supply Tank
CSA/AGA Design-Certified
Equipment Shutoff Valve With
1/8" NPT Tap*
Approved Flexible Gas
Hose (if allowed by
local codes)
Sediment
Trap
3" Minimum
Gas
Regulator
* Purchase the optional CSA/AGA design-certified equipment shutoff valve from your
dealer. See Accessories, page 19.
** Minimum inlet pressure for purpose of input adjustment.
104464
11
Vent Pointing Down
Figure 18 - External Regulator With Vent
Pointing Down
Continued
VENT-FREE PROPANE/LP GAS STOVE HEATER
INSTALLATION
3.
Continued
We recommend that you install a sediment
trap in supply line as shown in Figure 19,
page 11. Locate sediment trap where it is
within reach for cleaning. Install in piping
system between fuel supply and heater. Locate sediment trap where trapped matter is
not likely to freeze. A sediment trap traps
moisture and contaminants. This keeps them
from going into heater controls. If sediment
trap is not installed or is installed wrong,
heater may not run properly.
4.
5.
6.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1.
CAUTION: Avoid damage to
regulator. Hold gas regulator with
wrench when connecting it to gas
piping and/or fittings.
2.
3.
CHECKING GAS
CONNECTIONS
WARNING: Test all gas piping and connections for leaks
after installing or servicing. Correct all leaks at once.
WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water
to all joints. Bubbles forming
show a leak. Correct all leaks at
once.
CAUTION: Make sure external regulator has been installed
between propane/LP supply and
heater. See guidelines under Connecting to Gas Supply, page 11.
Pressurize supply piping system by either using compressed air or opening
propane/LP supply tank valve.
Check all joints of gas supply piping
system. Apply mixture of liquid soap
and water to gas joints. Bubbles forming show a leak.
Correct all leaks at once.
Reconnect heater and equipment
shutoff valve to gas supply. Check reconnected fittings for leaks.
4.
Close equipment shutoff valve (see Figure 20).
Pressurize supply piping system by either
using compressed air or opening propane/
LP supply tank valve.
Check all joints from gas meter to equipment shutoff valve (see Figure 21). Apply mixture of liquid soap and water to
gas joints. Bubbles forming show a leak.
Correct all leaks at once.
Pressure Testing Heater Gas
Connections
1.
2.
3.
4.
5.
6.
7.
Open equipment shutoff valve (see Figure 20).
Open propane/LP supply tank valve.
Make sure control knob of heater is in
the OFF position.
Check all joints from equipment shutoff
valve to control valve (see Figure 21).
Apply mixture of liquid soap and water to gas joints. Bubbles forming show
a leak.
Correct all leaks at once.
Light heater (see Operating Heater,
page 13). Check all other internal joints
for leaks.
Turn off heater (see To Turn Off Gas to
Appliance, page 13).
Open
ON
POSIT
Equipment
Shutoff
Valve
O
POS
Closed
Figure 20- Equipment Shutoff Valve
Equipment
Shutoff Valve
Propane/LP
Supply Tank
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1.
2.
Disconnect appliance with its appliance
main gas valve (control valve) and
equipment shutoff valve from gas supply piping system. Pressures in excess
of 1/2 psig will damage heater regulator.
Cap off open end of gas pipe where
equipment shutoff valve was connected.
Control Valve Location
Figure 21 - Checking Gas Joints
12
104464
OWNER’S MANUAL
OPERATING
HEATER
LIGHTING
INSTRUCTIONS
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Orange flame will also be present.
Open a window to vent smell. This
will only last a few hours.
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not follow these instructions exactly, a
fire or explosion may result causing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part
of the control system and any gas control which has been under water.
7.
1.
2.
3.
4.
5.
6.
STOP! Read the safety information,
column 1.
Make sure equipment shutoff valve
is fully open.
Turn control knob clockwise Clockwise
to the OFF position.
Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety information, column 1. If you don’t
smell gas, go to the next step.
Turn control knob counterclockwise
to the PILOT position.
C-clockwise
Press in control knob for five (5) seconds (see Figure 22).
Note: You may be running this
heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in
for 30 seconds or less. This will allow
air to bleed from the gas system.
With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep pressing ignitor button until pilot lights.
Note: If pilot does not stay lit, contact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Lighting Procedure, page 14.
8.
Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
• If control knob does not pop out when
released, contact a qualified service
person or gas supplier for repairs.
Note: If pilot goes out, repeat steps 3
through 7. This heater has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again.
Turn control knob counterclockwise
to desired heating level. The
burners should light. Set control knob
to any heat level between HI and LO.
C-clockwise
Pilot Burner
Thermocouple
Figure 23 - Pilot
CAUTION: Do not try to adjust
heating levels by using the equipment shutoff valve.
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater
Turn control knob clockwise
the OFF position.
Clockwise
to
Shutting Off Burners Only (pilot
stays lit)
Turn control knob clockwise
the PILOT position.
Clockwise
to
Control Knob
Ignitor Button
Figure 22- Control Knob and Ignitor
Button Location
Continued
104464
13
VENT-FREE PROPANE/LP GAS STOVE HEATER
OPERATING
HEATER
INSPECTING
BURNERS
Continued
Check pilot flame pattern and burner flame
patterns often.
THERMOSTAT
CONTROL
OPERATION
The thermostat control knob can be set to
any comfort level between Hi and Lo. The
thermostat will gradually modulate the heat
output and flame height from higher to
lower settings, or pilot, in order to maintain
the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated,
the output of the central heating system, etc.
Note: Selecting the Hi setting with the
control knob will cause the burner to remain fully on, without modulating down
in most cases.
PILOT FLAME PATTERN
Figure 24 shows a correct pilot flame pattern. Figure 25 shows an incorrect pilot flame
pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the
thermocouple to cool. When the thermocouple cools, the heater will shut down.
If pilot flame pattern is incorrect, as shown
in Figure 25
• turn heater off (see To Turn Off Gas to
Appliance, page 13)
• see Troubleshooting, pages 16 through 18
Pilot Burner
2.
3.
Follow steps 1 through 5 under Lighting Instructions, page 13.
Depress control knob and light pilot
with match.
Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 8 in Lighting Instructions,
page 13.
Btu (Variable)
16,000/30,000
Type Gas
Propane/LP Only
Ignition
Piezo
Pressure Manifold
8" W.C.
Inlet Gas Pressure (in. of water)
Maximum
14"
Minimum*
11"
Shipping Weight
28 lbs.
* For input adjustment
SERVICE HINTS
When Gas Pressure Is Too Low
• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specified heat
When Gas Quality Is Bad
Thermocouple
MANUAL LIGHTING
PROCEDURE
1.
SPECIFICATIONS
Figure 24 - Correct Pilot Flame Pattern
Pilot Burner
Thermocouple
• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit
You may feel your gas pressure is too low or
gas quality is bad. If so, contact your local
propane/LP gas supplier.
TECHNICAL
SERVICE
You may have further questions about installation, operation, or troubleshooting.
Figure 25 - Incorrect Pilot Flame Pattern
If so, contact DESA International’s Technical Service Department at 1-800-DESA LOG
(1-800-337-2564).
You can also visit DESA International’s
technical service web site at
www.desatech.com.
14
104464
OWNER’S MANUAL
CLEANING AND
MAINTENANCE
WARNING: Turn off heater
and let cool before cleaning.
4.
5.
6.
CAUTION: You must keep
control areas, burner, and circulating air passageways of heater
clean. Inspect these areas of
heater before each use. Have
heater inspected yearly by a qualified service person. Heater may
need more frequent cleaning due
to excessive lint from carpeting,
pet hair, etc.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
The primary air inlet holes allow the proper
amount of air to mix with the gas. This provides a clean burning flame. Keep these holes
clear of dust, dirt, and lint. Clean these air inlet
holes prior to each heating season. Blocked
air holes will create soot. We recommend that
you clean the unit every three months during
operation and have heater inspected yearly by
a qualified service person.
We also recommend that you keep the burner
tube and pilot assembly clean and free of
dust and dirt. To clean these parts we recommend using compressed air no greater than
30 PSI. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum
cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot
assembly. Note: Removing the rear panel
and top grates of your stove will make
cleaning easier.
1. Shut off the unit, including the pilot.
Allow the unit to cool for at least thirty
minutes.
2. Inspect burner, pilot, and primary air
inlet holes on injector holder for dust
and dirt (see Figure 26).
3. Blow air through the ports/slots and
holes in the burner.
Check the injector holder located at the
end of the burner tube again. Remove
any large particles of dust, dirt, lint, or
pet hair with a soft cloth or vacuum
cleaner nozzle.
Blow air into the primary air holes on
the injector holder.
In case any large clumps of dust have
now been pushed into the burner repeat
steps 3 and 4.
Clean the pilot assembly also. A yellow tip
on the pilot flame indicates dust and dirt in
the pilot assembly. There is a small pilot air
inlet hole about two inches from where the
pilot flame comes out of the pilot assembly
(see Figure 27). With the unit off, lightly
blow air through the air inlet hole. You may
blow through a drinking straw if compressed
air is not available.
Injector Holder
(May Be Brass
or Aluminum
Depending on
Model)
Burner
Tube
Primary Air Inlet
Holes (Shape of
Holes May Vary
by Model)
Figure 26 - Injector Holder On Outlet
Burner Tube
Ports/Slots
Burner
Tube
Pilot
Assembly
Pilot Air
Inlet
Hole
Figure 27 - Pilot Inlet Air Hole
104464
15
LOGS
• If you remove logs for cleaning, refer to
Installing Gas Log Heater into Stove,
page 10, to properly replace logs.
• Replace log(s) if broken or chipped
(dime-sized or larger).
MAIN BURNER
Periodically inspect all burner flame holes
with the heater running. All slotted burner
flame holes should be open with yellow
flame present. All round burner flame holes
should be open with a small blue flame
present. Some burner flame holes may become blocked by debris or rust, with no
flame present. If so, turn off heater and let
cool. Either remove blockage or replace
burner. Blocked burner flame holes will
create soot.
Review your video included with your heater
for additional cleaning instructions.
VENT-FREE PROPANE/LP GAS STOVE HEATER
TROUBLESHOOTING
WARNING: Turn off heater
and let cool before servicing. Only
a qualified service person should
service and repair heater.
Note: For additional help, visit DESA
International’s Technical Service web
site at www.desatech.com.
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage ODS/
pilot unit.
Note: All troubleshooting items are listed in
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at ODS/pilot
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3.
4.
5.
6.
When ignitor button is pressed, there is
spark at ODS/pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
5. ODS/pilot is clogged
6. Gas regulator setting is not correct
7. Depleted gas supply
ODS/pilot lights but flame goes out when
control knob is released
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged ODS/pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Replace ignitor cable
4. Replace piezo ignitor
5. Replace piezo ignitor
6. Replace piezo ignitor
1. Turn on gas supply or open equipment
shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is removed
5. Clean ODS/pilot (see Cleaning and
Maintenance, page 15) or replace ODS/
pilot assembly
6. Replace gas control
7. Contact local propane/LP gas company
1. Press in control knob fully
2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local propane/LP gas company
B) Clean ODS/pilot (see Cleaning and
Maintenance, page 15) or replace ODS/
pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace thermocouple
7. Replace control valve
www.desatech.com
16
104464
OWNER’S MANUAL
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after ODS/pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Maintenance, page 15) or replace burner orifice
2. Contact local propane/LP gas company
3. Replace burner orifice
2. Inlet gas pressure is too low
3. Burner orifice diameter is too small
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local propane/LP gas company
2. Clean burner (see Cleaning and Maintenance, page 15) or replace burner orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
1. Clean burner (see Cleaning and Maintenance, page 15) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
2. Damaged burner
3. Gas regulator defective
Slight smoke or odor during initial operation
1. Not enough air
2. Gas regulator defective
3. Residues from manufacturing processes
and logs curing
1. Check burner for dirt and debris. If
found, clean burner (see Cleaning and
Maintenance, page 15)
2. Replace gas control
3. Problem will stop after a few hours of
operation
Moisture/condensation noticed on windows
1. Not enough combustion/ventilation air
1. Refer to Air for Combustion and Ventilation requirements (page 4)
Heater produces a whistling noise when
burner is lit
1. Turning control knob to HI position
when burner is cold
2. Air in gas line
1. Turn control knob to LO position and
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local propane/LP gas company
3. Observe minimum installation clearances (see page 7)
4. Clean burner (see Cleaning and Maintenance, page 15) or replace burner orifice
3. Air passageways on heater blocked
4. Dirty or partially clogged burner orifice
Dark residue on logs or inside of fireplace
1. Improper log placement
2. Drafts or other air currents affecting
flame pattern
3. Air holes at burner inlet blocked
White powder residue forming within burner
box or on adjacent walls or furniture
4. Burner flame holes blocked
3. Clean out air holes at burner inlet. Periodically repeat as needed
4. Remove blockage or replace burner
1. When heated, vapors from furniture polish, wax, carpet cleaners, etc. turn into
white powder residue
1. Turn heater off when using furniture
polish, wax, carpet cleaners, or similar
products
www.desatech.com
104464
1. Properly locate logs (see Installing Gas
Log Heater Into Stove, page 10)
2. Eliminate source of drafts around heater
17
Continued
VENT-FREE PROPANE/LP GAS STOVE HEATER
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors.
Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors. These odors will disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Heater produces a clicking/ticking noise
just after burner is lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common with most heaters. If
noise is excessive, contact qualified service person
Heater produces unwanted odors
1. Heater burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (See IMPORTANT statement above)
2. Gas leak. See Warning statement at
top of page
1. Open window and ventilate room. Stop
using odor causing products while heater
is running
Heater shuts off in use (ODS operates)
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
1. Open window and/or door for ventilation
2. Contact local propane/LP gas company
3. Clean ODS/pilot (see Cleaning and
Maintenance, page 15)
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement at
top of page
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, page 12)
2. Replace control valve
Gas odor during combustion
1. Foreign matter between control valve
and burner
2. Gas leak. See Warning statement at
top of page
1. Take apart gas tubing and remove foreign matter
2. Locate and correct all leaks (see Checking Gas Connections, page 12)
2. Locate and correct all leaks (see Checking Gas Connections, page 12)
www.desatech.com
18
104464
OWNER’S MANUAL
PARTS CENTRALS
These Parts Centrals are privately owned businesses. They have agreed to support our
customer’s needs by providing original replacement parts and accessories.
Baltimore Electric
Washer Equipment Co.
Dayton Hardware
1348 Dixwell Avenue
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Parts Department
1715 Main Street
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
www.washerparts.com
Portable Heater Parts
East Coast Energy Products
P.O. Box 275
North Dayton Station
Dayton, OH 45404-0275
All States
937-258-3721
OH 1-800-762-3426
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
219-462-7441
1-800-362-6951
sales@portableheaterparts.com
techservice@portableheaterparts.com
707 Broadway
W. Long Branch, NJ 07764-1542
732-870-8809
1-800-755-8809
www.njplaza.com/ecep
FBD
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
1-800-654-8534
Fax: 1-800-846-0090
franktalk@aol.com
Master Parts Dist.
1251 Mound Ave NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Fax: 616-791-8270
www.nbmc.com
Tarantin Tank Co.
LA Porte’s Parts & Service
Heater & Fireplace Store
Cans Unlimited, Inc.
58 Halbe Lane
Cape May Court, NJ 08210-1110
609-390-1100
Parts Department
P.O. Box 645
Taylor, SC 29687-0013
All States
803-879-3009
1-800-845-5301
cuisales@aol.com
CLEANING KIT - CCK
(Not Shown)
Your vent-free gas appliance requires regular cleaning and maintenance to prevent
performance problems. This kit gives you
the tools and instructions to make it easy to
clean all critical areas of your appliance.
EQUIPMENT SHUTOFF
VALVE GA5010
For all models. Equipment shutoff valve with
1/8" NPT tap. Fits 1/2" NPT pipe.
104464
208 Carter Drive, Unit 21
West Chester, PA 19382-4500
610-430-7717
1-800-368-0803
www.halcoenterprises.com
P.O. Box 6129
Freehold, NJ 07728-6129
908-780-9340
1-800-922-0724
www.tarantin.com
ACCESSORIES
Purchase these heater accessories from your
local dealer. If they can not supply these
accessories, call DESA International’s Parts
Department at 1-800-972-7879 for referral
information. You can also write to the address listed on the back page of this manual.
Halco Enterprises
19
2444 N. 5th Street
Hartsville, SC 29550-7704
803-332-0191
Parts Department
VENT-FREE PROPANE/LP GAS STOVE HEATER
ILLUSTRATED
PARTS
BREAKDOWN
SL30PT
1
17
2
15
9
7
8
10
6
12
5
15
18
4
18
11
13
3
14
16
18
20
104464
OWNER’S MANUAL
PARTS LIST
This list contains replaceable parts used in your stove. For replacement parts see Parts Central on page 19
of this manual.
SL30PT
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
104459-01
098249-01
104384-03
104454-01
098867-10
104425-01
104422-02
099056-19
102843-01
102980-01
101329-22
104472-01
099211-01
102445-01
099387-13
098271-07
104286-01
M11084-38
Stove Log
Nut, M5
Painted Base Assembly
Bracket, Regulator
Gas Regulator
Inlet Tube
Outlet Burner Tube
Burner Orifice Injector
Burner Clip
Burner
Control Valve
Bracket
Screw
Piezo Ignitor
Pilot Tube
Ignitor Cable
ODS Pilot (LP)
Screw, Hex Head (#8-18 x .38)
QTY.
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
PARTS AVAILABLE — NOT SHOWN
100563-01
101054-01
100565-01
101137-04
104310-04
104464
Warning Plate
Lighting Instructions Plate
Warning Plate Fastener
Hardware Kit
Information Video
21
1
1
1
1
1
VENT-FREE PROPANE/LP GAS STOVE HEATER
ILLUSTRATED
PARTS
BREAKDOWN
CISC
CISG
1L
1C
7
1R
6
5-4
5-4
4
4
5-1
2
3
5-2
5-3
22
104464
OWNER’S MANUAL
PARTS LIST
This list contains replaceable parts used in your stove. For replacement parts see Parts Central on page 19
of this manual.
CISC
CISG
KEY
NO.
PART
NO.
1L
1C
1R
2
104171-06
104171-05
104171-07
104969-01
104969-02
104174-03
104970-01
104970-02
104971-01
*
*
3
4
5
5-1
5-2
5-3
*
5-4
*
6
104178-01
7
104968-01
DESCRIPTION
QTY.
Top Grate with Screen - Left (Black Only)
Top Grate with Screen - Center (Black Only)
Top Grate with Screen - Right (Black Only)
Bottom Door (Charcoal)
Bottom Door (Forest Green)
Stove Dropped Bottom
One Leg (Charcoal) (4 Total Per Stove)
One Leg (Forest Green) (4 Total Per Stove)
Hardware Kit
Door Hinge Step Bolt With Shoulder (1 Per Unit)
Door Catch Bolt M8 x 1.25 - 55mm Long With Two M8
Hex Nuts (1 Per Unit)
Bottom Floor Bolts M6 x 1 - 25mm Long With Flat Washer
And Lock Washer (4 Per Unit)
Leg Attachment Stud, Headless, Slotted,
M10 x 1.5 - 40mm Long
Back Panel Bolts M6 x 1 - 20mm Long With Flat Washer
And Lock Washer (6 Per Unit)
Stove Back Panel (Black Only)
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
PARTS AVAILABLE — NOT SHOWN
104108-08
104108-05
Touch-up Spray Paint 12 oz Can (Charcoal)
Touch-up Spray Paint 12 oz Can (Forest Green)
* Included In Hardware Kit
104464
23
1
1
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written
warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE/LP GAS LOG HEATERS AND EMPIRE STOVE CHASSIS
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers only the cost of part(s) required to restore this heater
to proper operating condition. Warranty part(s) MUST be obtained through authorized dealers of this product and/or DESA International
who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty. The heater
MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become
damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,
labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;
THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE TO TWO (2) YEARS FROM THE DATE OF FIRST PURCHASE; AND DESA
INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA
INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
104464 01
NOT A UPC
104464-01
Rev. C
02/00
Download PDF

advertising