Installation manual | Desa (V)JM36 Outdoor Fireplace User Manual

Outdoor Wood Burning Fireplace
OWNER’S OPERATION AND INSTALLATION MANUAL
(V)JM36, (V)JM42,
(V)JM50 Series, WCM-36J,
WCM-42J AND WCM-50J
Wood Burning Masonry
Fireplaces with Insulation
SAVE THIS BOOK
This book is valuable. In addition to instructing you
on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to ANS
Z21.60, Z21.84 or RGA 2-72 standards or for use with a ventfree gas log heater approved to ANS Z21.11.2 standard.
This wood burning fireplace complies with UL127CAN/ULS-S610-M87 standard as a FACTORY BUILT
APPLIANCE.
FOR CANADA: The authority having jurisdiction (such
as the municipal building department, fire department,
etc.) should be contacted before installation to determine the need to obtain a permit.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
For more information, visit www.desatech.com
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury, property
damage or loss of life. Refer to this manual for assistance or additional information. Consult a qualified
installer or local distributor.
Table of Contents
Safety................................................................... 2
Specifications....................................................... 3
Fireplace Installation............................................ 6
Venting Installation............................................... 8
Optional Gas Line Installation............................ 13
Brick Installation................................................. 14
Glass Door Installation....................................... 29
Operation and Maintenance Guidelines............. 31
Technical Service............................................... 33
Replacement Parts............................................. 33
Parts .................................................................. 34
Accessories........................................................ 37
Safety
IMPORTANT: Check local codes
before installing this fireplace.
Before beginning the installation of the
fireplace, read these instructions through
completely.
• This DESA Heating, LLC fireplace and its
components are safe when installed according to this installation manual. Unless
you use DESA Heating, LLC components,
which have been designed and tested for
the fireplace system, you may cause a fire
hazard.
• The DESA Heating, LLC warranty will be
voided by and DESA Heating, LLC disclaims any responsibility for the following
actions.
a. Modification of the fireplace, components, doors, air inlet system and
damper control.
b. Use of any component part not manufactured or approved by DESA Heating, LLC in combination with a DESA
Heating, LLC fireplace system.
Proper installation is the most important step
in ensuring safe and continuous operation
of the fireplace. Consult the local building
codes as to the particular requirements
concerned with the installation of all factory
built fireplaces.
WARNING: Do not install a
fireplace insert in this box unless
the manufacturer's instructions
with the insert specifically state
this fireplace has been tested for
use with this insert.
FOR YOUR SAFETY
• Do not store or use gasoline
or any other flammable vapors
or liquids in the vicinity of this
or any other appliance.
• Due to high temperatures, the
appliance should be located
out of traffic and away from
furniture and draperies.
• Do not place clothing or other
flammable materials on or near
the appliance.
• Never leave children unattended when a fire is burning
in the fireplace.
WARNING: Use solid wood
or processed solid fuel firelogs
only. When processed wood fuel
fire logs are used, do not poke or
stir the logs while they are burning. Use only fire logs that have
been evaluated for the application
in fireplace and refer to fire log
warnings and caution markings
on packaging prior to use.
This fireplace is not intended to be
used as a substitute for a furnace
to heat an entire home. Use for
supplemental heat only.
www.desatech.com
122273-01A
Specifications
36" mODELS
29"
22 1/2"
14 1/2"
22"
18 3/8" 19 13/16"
(Ref.)
26 5/8"
15 5/8"
35 3/8"
36" HEARTH
4 1/2"
1 5/16"
11"
OUTSIDE AIR
ACCESS
67"
61"
49"
58"
GAS LINE
ACCESS
30"
7"
1"
1"
36"
45 1/8"
10 1/2" 9 1/2"
3 1/2"
4 1/2"
7 1/4"
11"
15 1/4"
Figure 1 - 36" Models (V)JM36 Series and WCM-36J
122273-01A
www.desatech.com
Specifications Continued
42" Models
30 1/2"
22 3/4"
15 3/4"
25"
22 1/2"
23 13/16"
(Ref.)
29"
17 5/8"
4 3/8"
41 3/8"
1 5/16"
42" HEARTH
5/8"
OUTSIDE
AIR
ACCESS
11"
67" 58"
61"
49"
GAS LINE
ACCESS
30"
10 1/2" 9 1/2"
3 1/2"
7"
1"
42"
51 1/8"
4 1/2"
81/2"
13"
17"
Figure 2 - 42" Models (V)JM42 Series and WCM-42J
www.desatech.com
122273-01A
Specifications Continued
50" Models
38 1/2"
24"
19 1/4"
33"
23 13/16"
22 1/2"(Ref.)
28 1/2"
17 5/8"
49 3/8"
50" HEARTH
43/8"
OUTSIDE
AIR
ACCESS
11"
67"
61"
1 5/16"
GAS LINE
ACCESS
58"
49"
30"
10 1/2"
7"
1"
50"
59"
9 1/2"
3 1/2"
4 1/2"
8 1/2"
13"
17"
Figure 3 - 50" Models (V)JM50 Series and WCM-50J
122273-01A
www.desatech.com
Fireplace Installation
selecting location
Framing
To determine the safest and most efficient
location for the fireplace, you must take into
consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 4 and 5).
2. Consider a location where fireplace will
not be affected by drafts, air conditioning
ducts, windows or doors.
3. A location that avoids cutting of joists or
roof rafters will make installation easier.
4. An outside air kit is available with this
fireplace (see Optional Outside Air Kit on
page 8).
1. Frame opening for fireplace using dimensions shown in Figures 4 and 5.
2. If fireplace is to be installed directly on
carpeting, tile (other than ceramic) or any
combustible material other than wood
flooring, fireplace must be installed upon
a metal or wood panel extending full width
and depth of fireplace.
3. Set fireplace directly in front of this opening and slide unit back until nailing flanges
touch side framing.
4. Check level of the fireplace and shim with
sheet metal if necessary.
5. Before securing fireplace to prepared
framing, ember protector (provided) must
be placed between hearth extension (not
supplied) and under bottom front edge of
fireplace to protect against glowing embers
falling through. If fireplace is to be installed
on a raised platform, a Z-type ember protector (not supplied) must be fabricated to
fit your required platform height. Ember
protector should extend under fireplace a
minimum of 1 1/2". Ember protector should
be made of galvanized sheet metal (28
gauge minimum to prevent corrosion.
6. Using screws or nails, secure fireplace to
framing through flanges located on sides
of fireplace.
Minimum clearance to
combustibles
Back and sides of fireplace
1 1/2" min.*
Front of fireplace
48" min.
Floor**
0" min.
Perpendicular wall to opening
18" min.
36" Models
12" min.
Top spacers
0" min.
Mantel clearances
see Mantels, page 7
Chimney outer pipe surface
2" min.
36" Model
1" min.
* Not required at nailing flanges
** See step 2 of Framing
WARNING: Do not pack required air spaces with insulation
or other materials.
Minimum/Maximum Chimney Height for
Residential Installation
Minimum height of chimney, measured from
base of fireplace to flue gas outlet of termination, is 16 feet for straight flue or a flue with
one elbow set. Maximum distance between
elbows is 6 feet. For systems with two elbow
sets, minimum height is 22 feet. Maximum
height of any system is 50 feet. This measurement includes fireplace, chimney sections and
height of termination assembly at level of the
flue gas outlet (see Figure 15, page 11).
Minimum/Maximum Chimney Height for
Outdoor Installation
Minimum height of chimney, measured
from base of fireplace to flue gas outlet of
termination, is 9.5 feet (minimum of 4 feet of
chimney pipe sections required for outdoor
installation).
67.125"
58.125"
45.25" (36" Models)
51.25" (42" Models)
59" (50" Models)
30.125"
28.250" (36" Models)
Figure 4 - Framing Dimensions
Maintain 1 1/2"
Clearance
at Sides and
Back of Fireplace
61" (36" Models)
65" (42" Models)
71" (50" Models)
1 1/2" Clearance
Not Required at
Nailing Flanges
86.5" (36" Models)
92" (42" Models)
100" (50" Models)
Figure 5 - Corner Installation
www.desatech.com
122273-01A
Fireplace Installation
Continued
Hearth Extension
Mantels
A mantel may be installed if desired (see Figure
7). Woodwork such as wood trims, mantels or
any other combustible material projecting from
front face must not be placed within 12" (36"
Models) or 18" (42/50" Models) of fireplace
opening. Combustible materials above 12" (36"
Models) or 18" (42/50" Models) and projecting
more than 1 1/2" from fireplace must not be
placed less than 15" (36" Models) or 21" (42/50"
Models) from the top opening of the fireplace
(NFPA STD 211, Sec. 7-3.3.3).
Mantels or any other combustible material
also may come up to side edge of black metal
face of fireplace as long as projections from
front face fall within limit shown in Figure 7.
WARNING: Hearth extension
is to be installed only as shown
in Figure 6.
Seal Gap
Fireplace Front
Hearth
Extension
Seal Gap
Combustible
Material
Safe
Zone for
Projection of
Combustible
Materials
3" Nom.
11/2" Max.
Upper
Section of
Fireplace
Fireplace Opening
Top View of Fireplace
33°
Ember Protector
Figure 6 - Hearth Extension
122273-01A
33°
SAFE ZONE
Fireplace Front
Raised Hearth
Fireplace Front
Elevated
12 1/4" Ref.
7.75" (36" Models)
11.5" (42/50" Models)
Ember Protector
Ember Protector
15" Min. (36" Models)
21" Min. (42/50"
Models)
A hearth extension projecting a minimum of
20" in front of and a minimum of 12" beyond
each side of fireplace opening is required to
protect combustible floor construction in front
of fireplace. Fabricate a hearth extension
using a material which meets the following
specifications: a layer of noncombustible,
inorganic material having a thermal conductivity of K=0.84 BTU IN/FT, HR. F (or less) at
1" thick. For example, if the material selected
has a K factor of 0.25, such as glass fiber, the
following formula would apply:
0.25 x 1.0" = 0.30" thickness required
0.84
Thermal conductivity "K" of materials can be 6"
obtained from manufacturer or supplier of Ref.
noncombustible material. If hearth extension
is to be covered, use noncombustible material such as tile, slate, brick, concrete, metal,
glass, marble, stone, etc. Provide a means
to prevent hearth extension from shifting and
seal gap between fireplace frame and hearth
extension with a noncombustible material
(see Figure 6).
12" Min.
(36" Models)
18" Min.
(42/50"
Models)
Note: For outdoor installations, fireplace
enclosure must allow for adequate drainage
and fresh air ventilation. It is recommended
that a sealed, corrosion resistant catch pan
with provision for drainage be installed under
fireplace within fireplace enclosure.
FIREBOX
3" Max.
Combustible
4.5" Material
Must Not
Overlap
Front Face
Min. to
Perpendicular
Side Wall
12" - 36" Models
18" - 42/50" Models
Figure 7 - Mantel Clearances to
Combustible Material
www.desatech.com
Venting Installation
Optional Outside air Kit
(Model ak4/ak4f)
PART NO.
The installation of an outside air kit should
be performed during the rough framing of
the fireplace due to the nature of it's location.
Outside combustion air is accessed through
a vented crawl space (AK4F) or through a
sidewall (AK4).
CAUTION: Combustion air
inlet ducts shall not terminate
in attic space.
Secure to Collars with Metal Tape,
Screws or Straps (Min. of 1/4" x 20"
in size)
Air Inlet
Location
Must Allow
For Bushes
or Snow
GAIN
Georgian
Fireplace
66 1/2"
12-12DM
Pipe Section
10 5/8"
12-12HT
18-12DM
Pipe Section
16 5/8"
18-12HT
24-12DM
Pipe Section
23 5/8"
24-12HT
36-12DM
Pipe Section
34 5/8"
36-12HT
48-12DM
Pipe Section
46 5/8"
48-12HT
RLT-12D
Round Termination
7 3/4"*
RLT-12HT
Square Chase-Top
STL-12D
7" to 15"*
with Slip Section
* The lineal gain for the terminations is measured to the flue gas outlet height.
12" Galvanized
Outer Pipe
Air Inlet
Eyebrow
Vent Hood
Vented Crawl Space
Required for
(Check Local Codes
Wall Installation
Before Installing in a
Vented Crawl Space)
Figure 8 - Outside Air Kit
Chimney Pipe
The DESA Heating, LLC chimney system
consists of 12", 18", 24", 36" and 48" snaplock, double-wall pipe segments, planned
for maximum adaptability to individual site
requirements. Actual lengths gained after
fitting overlaps must be taken into consideration (lineal gain) and are given in the lineal
gain chart (see Figure 9). Lineal Gain is the
actual measurable length of a part after two or
more parts are connected. For Canada, use
chimney parts designated "HT".
WARNING: The opening in the
collar around the chimney at the
top of the fireplace must not be
obstructed. Never use blown insulation to fill the chimney enclosure.
LINEAL GAIN
DESCRIPTION
Hemmed
End
12 3/8"
Stainless
Inner Pipe
Figure 9 - Lineal Gain
Assembly and installation of
double wall chimney system
Each double wall chimney section consists
of a galvanized outer pipe, a stainless steel
inner flue pipe and a wire spacer. The pipe
sections must be assembled independently
as the chimney is installed. When connecting
chimney directly to the fireplace, the inner flue
pipe section must be installed first with the
lanced side up. The outer pipe section can
then be installed over 5 the flue pipe section
with the hemmed end up. Press down on each
pipe section until the lances securely engage
the hem on the fireplace starter. The wire will
assure the proper spacing between the inner
and outer pipe sections.
Continue to assemble chimney sections as
outlined above, making sure that both the
inner and outer pipe sections are locked together. When installing double wall snap-lock
chimney together, it is important to assure
the joint between the chimney sections is
locked. Check by pulling chimney upward
after locking. The chimney will not come apart
www.desatech.com
122273-01A
Venting Installation
Continued
if properly locked. It is not necessary to add
screws to keep the chimney together (exception, see Figure 10).
Using ELBOW offsets (30E-12DM)
1. To achieve desired offset, you may install
combinations of 12", 18", 24", 36" and 48"
length of double wall pipe (see offset chart
and Figure 10).
OFFSET
A
RISE
B
4 3/8"
9 3/4"
12 3/4"
15"
18"
21 1/4"
23 3/4"
27 3/4"
30"
33"
36"
38 1/4"
41 1/4"
45"
46 3/4"
51"
53 1/4"
56 1/4"
59 1/4"
61 3/4"
64 3/4"
68 1/4"
70"
74 1/4"
76 3/4"
79 3/4"
16 3/8"
25 1/2"
30 3/4"
34 3/4"
40"
46 1/4"
49 1/4"
56 3/4"
60 3/4"
66"
71"
75"
80 1/4"
86 3/4"
89 1/2"
97"
101"
106 1/4"
111 1/2"
115 1/2"
120 3/4"
127"
130"
137 1/2"
141 1/2"
146 3/4"
12"
CHIMNEY LENGTH
18" 24" 36" 48"
ELBOW SET ONLY
1
1
2. Chimney weight above offset rests on
return elbow. Straps must be securely
nailed to rafters or joists (see Figure 11,
details A and B).
3. Maximum length of pipe between supports (return elbow or 12S-12DM) is 6'
of angle run. Maximum of two 6' angle
run sections per chimney system (see
Figure 12, page 10).
4. All pipe connections between the offset
and return must be secured with two
screws on the outer pipe only (see
Figure 10). Do not penetrate the inner
stainless.
1
1
See Detail A
1
1
1
2" Min.
1
1
1
1
1
1
1
1
1
1
1
Straps
Detail B
Angle Firestop
2
1
2
1
2
1
1
1
1
2
1
1
Straps
1
2
2
4
1
See Detail B
1
1
2
1
2
2
1
2
1
1
Straps
Straps
Detail A
Return Elbow
Figure 11 - Ceiling Support Pipe
12S-12DM
OFFSET CHART (22-50 FT. SYSTEM HEIGHT)
Screws
B
A
Figure 10 - Elbow Offset
122273-01A
www.desatech.com
Venting Installation
Continued
Return
Elbow
Return
Elbow
Offset
Elbow
Return
Elbow
Offset
Elbow
6' Max.
Return
Elbow
6' Max. Ceiling
Support Pipe
12S-12DM
Return
Elbow
6' Max.
Offset
Elbow
Offset
Elbow
A
Offset
6' Max. Elbow
B
6' Max.
6' Max.
C
Figure 12 - Typical Offset Terminations
Firestop Spacers (FS-10,
1100EFS-10DM for 36" Models)
Firestop spacers are required at each point
where the chimney penetrates a floor space.
Their purpose is to establish and maintain
the required clearance between the chimney
and the combustible materials. When the pipe
passes through a framed opening into a living
space above, the firestop must be placed onto
the ceiling from below as shown in Figure 13.
They also provide complete separation from
one floor space to another or attic space as
required by most codes. When the double wall
pipe passes through a framed opening into an
attic space, the firestop must be placed into an
attic floor as shown in Figure 14.
Existing
Ceiling
Frame
Firestop
Spacer
Screws or
Staples
(Min. of 8)
Figure 13 - Firestop Spacer with Living
Space Above Ceiling
10
Firestop
Spacer
Screws or Staples
(Min. of 8)
Existing
Ceiling
Frame
Figure 14 - Firestop Spacer with Attic
Space Above Ceiling
Penetrating the roof
To maintain a 1" (36" Models) or 2" (42/50"
Models) clearance to the pipe on a roof with a
pitch, a rectangular opening must be cut.
1. Determine center point through which pipe
will penetrate roof.
2. Determine center point of roof. Pitch is
distance the roof drops over a given span,
usually 12". A 6/12 pitch means that roof
drops 6" for each 12" measured horizontally down from roof rafters.
3. Use roof opening chart (Figure 15, page
11) to determine correct opening length
and flashing required.
4. Remove shingles around opening measured. Cut out this section.
www.desatech.com
122273-01A
Venting Installation
Continued
5. Add next sections of pipe until end
penetrates roof line. Check to see that
proper clearances are maintained. Extend
chimney by adding sections of double wall
pipe until pipe is minimum of 30" above
highest point of roof cutout. Termination
and chimney must extend a minimum of
36" above highest point where it passes
through roof.
17" Min.
30" Min.
1" Min.
1" Min.
1" Min.
Opening "A"
Pitch
Slope
0°
26.6°
Opening
"A" Max.
17"
19"
Used Flashing
Model No.
V6F-10DM
V6F-10DM
Flat
0-6/12
6/1212/12
45.0°
24"
V12F-10DM
Flashing installation (v6f-10dm
or v12f-10dm)
Determine the flashing to be used with the roof
opening chart. Slide flashing over pipe until
base is flat against roof. Replace as many
shingles as needed to cover exposed area
and flashing base. Secure in position by nailing through shingles (see Figure 16). DO NOT
NAIL THROUGH FLASHING CONE.
Installing Flashing on a Metal Roof
When installing the flashing on a metal roof,
it is required that putty tape be used between
the flashing and the roof. The flashing must be
secured to the roof using #8 x 3/4" screws and
then sealed with roof coating to prevent leakage through the screw holes. A roof coating
must also be applied around the perimeter of
the flashing to provide a proper seal.
Overlap
Storm Collar
Shingles Top
Flashing
and Sides Only
Cone
Nail Only
Outer
Perimeter
of Flashing
Roof Opening 36" Models
19.5" Min.
30" Min.
2" Min.
2" Min.
Underlap Shingles
at Bottom
Figure 16 - Flashing Installation
2" Min.
Opening "A"
Pitch
Slope
Flat
0-6/12
6/1212/12
0°
26.6°
45.0°
Opening Used Flashing
"A" Max.
Model No.
19.5"
V6F-10DM
22'
V6F-10DM
27"
Storm Collar Installation (SC2-1)
Place storm collar over pipe and slide down
until it is snug against the open edge of the
flashing (see Figure 17). Apply waterproof
caulk around the perimeter of the collar to
provide a proper seal.
Chimney
Pipe
Waterproof
Caulk
Storm
Collar
Flashing
V12F-10DM
Roof Opening 42" and 50" Models
Figure 15 - Roof Opening Measurements
Figure 17 - Storm Collar
122273-01A
www.desatech.com
11
Venting Installation
Continued
Terminations/Spark Arrestor
The fireplace system must be terminated with
the listed round top or chase terminations. In
any case, refer to the installation instructions
supplied with the termination.
CAUTION: Do not seal openings on the rooftop flashing. Follow the installation instructions
provided with the termination
being used.
Stainless
Inner Flue
Pipe
Secure
Termination
to Outer
Pipe with 3
Screws
18"
Min.
Typ.
24" Min.
24" Min.
RTL-10D
Level of
Flue Gas
Outlet
Waterproof
Caulking
Storm
Collar
Figure 19 - Multiple Chase Installation
10 foot rule
All flue gas outlet chimney terminations must
extend a minimum of 3 feet in height above the
highest point where it passes through the roof
and must be at least 2 feet above the highest point of the roof that is within a horizontal
distance of 10 feet (see Figure 20).
Level of
Flue Gas
Outlet
10'
10'
Flashing
Overlap
Shingles (Top
and Sides of
Flashing Base)
2' Min.
Underlap
Shingles
3' Min.
2' Min.
3' Min.
Figure 18 - Termination
Chase installations
Figure 20 - 10 Foot Rule
Instructions for chase installations are
included with the chase style termination
chosen. In a multiple chase installation, be
sure to provide adequate distance between
terminations to prevent smoke spillage from
one termination to another. We suggest that
terminations be separated at least 24", center
to center and stacked at a vertical height difference of 18" (see Figure 19).
Note: If a decorative shroud is to be installed,
contact the manufacturer for specifications.
12
finishing the fireplace
Combustible materials, such as wallboard,
gypsum board, sheet rock, drywall, plywood,
etc. may make direct contact with sides and top
around the fireplace face. It is important that
combustible materials do not overlap the face
itself. Brick, glass, tile or other noncombustible
materials may overlap the front face provided
they do not obstruct essential openings like
louvered slots or any other opening. When
overlapping with a noncombustible facing
material, use only noncombustible mortar or
adhesive.
www.desatech.com
122273-01A
Optional Gas Line Installation
Gas line hook up should be done by your
supplier or a qualified service person.
Note: Before you proceed, make sure your
gas supply is turned off.
Use only a 1/2" black iron pipe and appropriate fittings.
1. Remove knockout indentation on refractory or firebrick wall located above refractory hearth floor. Knockout indentation
must be firmly tapped with any solid object
such as a 1/2" dowel until it is released.
Remove fragmented portions of refractory
(see Figure 21).
2. Remove gas line cover plate located on
either side of fireplace and pull out insulation from gas line conduit sleeve. Save
insulation for reuse. Replace screws.
3. Run a 1/2" black iron gas line into fireplace
through the rear at gas line conduit sleeve (if
using a raised platform, add height). Provide
sufficient gas line into fireplace chamber for
fitting connection (see Figure 22).
Note: Secure incoming gas line to wood
framing to provide rigidity for threaded end.
4. Repack insulation around gas line and into
sleeve opening. Seal any gaps between
gas line and refractory knockout hole with
refractory cement or commercial furnace
cement, Install the gas appliance or cap-off
gas line if desired.
CAUTION: All gas piping
and connections must be tested
for leaks after the installation
is completed. After ensuring
that the gas valve is on, apply
soap and water solution to all
connections and joints. Bubbles
forming show a leak. Correct
all leaks at once. DO NOT USE
AN OPEN FLAME FOR LEAK
TESTING AND DO NOT OPERATE ANY APPLIANCE IF A LEAK
IS DETECTED. LEAK TESTING
SHOULD BE DONE BY A QUALIFIED SERVICE PERSON.
WARNING: Do not operate an
unvented gas log set in this fireplace with the chimney removed.
122273-01A
If you install a decorative gas appliance
(vented gas log), the decorative gas appliance
must comply with the Standard for Decorative
Gas Appliance for Installation in Solid Fuel
Burning Fireplaces, ANS Z21.60, Z21.84 or
RG 2-72 and shall also be installed in accordance with the National Fuel Gas Code, ANSI
7223NFPA 54 latest edition.
WARNING: If the fireplace
has been used for wood burning,
the firebox and chimney must be
cleaned of soot, creosote and
ashes be a qualified chimney
cleaner. Creosote will ignite if
heavily heated.
WARNING: When using a
decorative vented gas log, the
damper must be removed or permanently locked in the fully open
position and the glass doors must
be in the fully open position.
Outside of
Fireplace
Gas Line
Conduit
Insulation
Remove
Knockout
Side
Firebrick
Finished
Side
1/2" Dowel
Gas
Conduit
Cover
Brick with
Access
Hole
Figure 21 - Gas Line Access
Side
Outside of
Firebrick
Fireplace
Finished
Incoming
Side
1/2" Black
Gas Line
Iron Pipe
Conduit
Repack
Insulation
Seal
Opening
with
Refractory
Cement
Provide Enough
Threaded
End for Fitting
Connection
Figure 22 - Gas Line Installation
www.desatech.com
13
Brick Installation
Brick Panel Installation
IMPORTANT: Installation of brick
should be done after the fireplace is placed in a permanent
location.
The brick housings are already installed on
the panels. When installing brick housing
panels into fireplace, wear gloves as edges
may be sharp.
1. Beginning with left side panel, place
panel, bottom edge first, at an angle into
fireplace. Secure to bottom of fireplace
with screws provided.
2. Install right side as left side in step 1 using
screws provided.
3. Install back panel and secure back to
sides and bottom of firebox with screws
provided.
4. Using self-tapping screws and a drill, place
screws into large holes in back and side
panels (see Parts, page 34), through wire
mesh and into firebox wrapper to secure.
Brick Installation
Each brick housing is stamped with a number
(full size bricks are not stamped). These numbers will help identify the brick when installing.
It is important to install these bricks exactly as
instructed. Press brick firmly into brick housing
until it snaps. Groove line on side of brick will
come in contact with flange on the brick housing. This secures brick into housing (see Figure
24). Smaller bricks may require a small portion
of furnace cement applied to back of brick to
secure it until grouting has been completed.
Bricks are packaged in separate boxes. The
brick matrixes on pages 15 through 27 show
how bricks are packaged and placed for each
size fireplace and the number of bricks per
box. There are 2 extra full bricks included in
Hearth Brick package.
Install bricks one section at a time starting with
hearth panel followed by the rear panel, left
panel and right panel. It is important to install
the bricks in sequence. Please note, full size
bricks are NOT stamped.
Stamped
Letter
Location
Brick
Hole in
Side Panel
Flanges
Figure 23 - Hole in Side Panel to Attach
to Firebox Wrapper
Brick Housing
Figure 24 - Installing Brick
14
www.desatech.com
122273-01A
Brick Installation
Continued
HEARTH BRICK MATRIX
FULL
F124
FULL
FULL
F126
FULL
F128
QTY
11*
RED
IVORY
FULL
FULL
(112140-01) (112140-05)
ASH BRICK ASH BRICK
(120848-01) (120848-03)
F011R
F011W
F059R
F059W
F123R
F123W
F124R
F124W
F126R
F126W
F132R
F132W
F133R
F133W
* Includes 2 extra bricks.
QTY
13*
RED
IVORY
FULL
FULL
(112140-01) (112140-05)
ASH BRICK ASH BRICK
(120848-01) (120848-03)
F011R
F011W
F012R
F012W
F021R
F021W
F024R
F024W
F025R
F025W
F059R
F059W
F126R
F126W
F134R
F134W
F135R
F135W
* Includes 2 extra bricks.
QTY
17*
FULL
FULL
F126
FULL
120848
FULL
F125
RED
IVORY
FULL
FULL
(112140-01) (112140-05)
ASH BRICK ASH BRICK
(120848-01) (120848-03)
F012R
F012W
F124R
F124W
F125R
F125W
F126R
F126W
F128R
F128W
* Includes 2 extra bricks.
F124
FULL
Ash Brick
F012
F012
F125
F128
36" Hearth
F133
F123
F011
FULL
FULL
F132
FULL
FULL
FULL
FULL
120848
FULL
F126
F059
F123
FULL
FULL
F124
F133
Ash Brick
F059
F124
FULL
FULL
F059
F126
F132
F059
42" Hearth
F135
FULL
F024
F126
F021
F134
FULL
FULL
FULL
FULL
120848
Ash Brick
F012
F012
50" Hearth
122273-01A
F135
FULL
FULL
FULL
FULL
F059
F011
F011
FULL
FULL
FULL
F025
F011
F024
F126
FULL
FULL
F021
FULL
F059
F134
F025
www.desatech.com
1
2
2
2
2
2
1
1
4
2
2
2
2
2
1
3
2
2
2
2
2
2
2
2
15
Brick Installation
Continued
36" FULL STACKED BRICK MATRIX
F147
FULL
FULL
F159
FULL
FULL
FULL
FULL
F143
FULL
F143
F158
F143
F158
FULL
F144
F185 or
F191
F143
F036
FULL
FULL
F158
F144
F158
16
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
8
(112140-01) (112140-05)
F148R
F150R
F152R
F153R
F159R
F160R
F148W
F150W
F152W
F153W
F159W
F160W
1
2
1
2
6
4
F153
F148
FULL
F158
F143
F158
F185 or
F191
3
2
1
1
2
3
1
1
1
F147
F148
FULL
F144
F160
F152
F148
FULL
F144
F160
FULL
F160
F159
FULL
F159
F159
F160
F185 or
F191
F036R
F036W
F143R
F143W
F036
FULL
F144R
F144W
F147R FULL F147W
F148R
F148W
F158R
FULL
F036F158W
F185R
F185W
F191R F192 F191W
F192R
F192W
F150
F148
FULL
FULL
F158
F159
F150
F159
F158
F185 or
F191
F192
F148
LEFT
REFRACTORY
RED
QTY
FULL
F036IVORY
FULL
FULL
7
(112140-01)
(112140-05)
FULL
FULL
F158
F143
FULL
F036
F158
F158
FULL
FULL
LL
F158
FULL
F036
F147
F148
F143
FULL
LL
LL
FULL
F036
F153
F147
F148
F143
F148
F036
FULL
FULL
F036
F192
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
7
(112140-01) (112140-05)
F036R
F143R
F144R
F147R
F148R
F158R
F185R
F191R
F192R
www.desatech.com
F036W
F143W
F144W
F147W
F148W
F158W
F185W
F195W
F192W
3
2
1
1
2
3
1
1
1
122273-01A
Brick Installation
Continued
42" FULL STACKED BRICK MATRIX
FULL
FULL
F032
F033
FULL
F033
FULL
F032
F154
F156
F143
F143
F143
F143
F151
FULL
FULL
F151
122273-01A
F033
F032
FULL
FULL
F158
F143
F143
F158
186
FULL
F017R
F032R
F033R
F152R
F154R
F157R
F190 or F186
1
3
3
3
1
1
1
2
1
1
F017W
F032W
F033W
F152W
F154W
F157W
2
6
4
2
2
2
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
8
(112140-01) (112140-05)
F143
F033
F032
FULL
F032W
F033
F033W
F143W
F032
F151W
F155W
F033
F156W
F158W
F032
F186W
F190W
F154
F155
FULL
F032
F017W
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
7
(112140-01) (112140-05)
F033
F152
FULL
F032R
FULL
FULL
F033R
F143R
FULL
F158
F151R
F155R
FULL
FULL
F156R
F190F158R
or F186
F151
F186R
F190R
F032
F017
F158
F033
FULL
FULL
F156
FULL
F017R
F032
F152
F158
FULL
FULL
FULL
LEFT REFRACTORY
F155
RED
IVORY
QTY
FULL
FULL
F033
FULL
FULL
8
(112140-01) (112140-05)
F017
F157
F032
FULL
F032
F151
F017
FULL
F033
FULL
FULL
F017
F158
F158
F190 or F186
F032
FULL
FULL
FULL
F032
F157
F158
F143
F033
FULL
F143
F032
F143
FULL
F156
F143
F033
F156
F017
F143
F155
F033
F032
www.desatech.com
F017R
F032R
F033R
F143R
F151R
F155R
F156R
F158R
F186R
F190R
F017W
F032W
F033W
F143W
F151W
F155W
F156W
F158W
F186W
F190W
1
3
3
3
1
1
1
2
1
1
17
Brick Installation
Continued
50" FULL STACKED BRICK MATRIX
F147
FULL
FULL
FULL
F159
F159
FULL
F153
FULL
F145 or
F191
F144
F158
18
F148
F148
FULL
FULL
F145 or
F191
F143
F143
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
13
(112140-01) (112140-05)
F148R
F150R
F152R
F153R
F159R
F160R
F148W
F150W
F152W
F153W
F159W
F160W
2
2
2
2
6
4
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
7
(112140-01) (112140-05)
F144
F033
F032
FULL
FULL
F158
F149
F032
FULL
F033
F153
FULL
FULL
3
1
1
F191
F160
FULL
F152
F158R F192 F158W
F191R
F191W
F192R
F191W
F143
F143
FULL
F152
F158
F143
F143
F143
F158
FULL
FULL
F158
F144
L
F160
F147
F148
FULL
FULL
FULL
3
3
2
1
1
1
1
2
1
F150
FULL
FULL
FULL
F160
F158
FULL
FULL
F160
F147
F148
F159
F148
F159
F150
F158
F145 or
F191
F146 or
F192
F032R
F032W
F033
F033RFULL F033W
F143R
F143W
FULL
F032
F158
F144R
F144W
F145R
F145W
FULL
FULL
F033
F146R
F146W
F147R
F147W
FULL
F032
F158
F148R
F148W
F145 or F149RF146 or F149W
FULL
F159
F032
F033
F158
FULL
FULL
F158
F159
F032
F033
F158
FULL
FULL
LEFT REFRACTORY
RED F148 IVORY
QTY
F149
FULL
FULL
7
FULL
F032
(112140-01)
(112140-05)
F148
F143
F033
F147
F148
FULL
F032
L
L
F148
F144
F149
F033
F032
F146 or
F192
F033
www.desatech.com
F032R
F033R
F143R
F144R
F145R
F146R
F147R
F148R
F149R
F158R
F191R
F192R
F032W
F033W
F143W
F144W
F145W
F146W
F147W
F148W
F149W
F158W
F191W
F192W
3
3
2
1
1
1
1
2
1
3
1
1
122273-01A
Brick Installation
Continued
36" FULL HERRINGBONE BRICK MATRIX
F074
F074
15
F1
F0
72
F0
FU
72
68
F0
LEFT REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F068R
F068W
F071R
F071W
F072R
F072W
F074R
F074W
F113R
F113W
F115R
F115W
F165R
F165W
F181R
F181W
F189R
F189W
S011R
S011W
QTY
6
FU
13
F1
LL
LL
F0
FU
72
FU
13
F1
LL
LL
13
F1
FU
72
LL
F0
FU
LL
F0
F1
72
89
F1
65
1
1
5
2
3
1
1
1
1
1
F181 or F071
S011
F074
F074
F117
F1
LL
FU
84
F0
08
68
F0
72
F0
F074
F074
07
LL
F1
FU
LL
FU
84
F0
F074
LL
07
F1
FU
84
F0
LL
FU
F074
0
F1
LL
FU
7
9
6
F1
7
F1
8
68
6
F1
1
F1
F187
REAR REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F068R
F068W
F072R
F072W
F074R
F074W
F084R
F084W
F107R
F107W
F108R
F108W
F117R
F117W
F161R
F161W
F168R
F168W
F179R
F179W
F187R
F187W
QTY
6
1
1
6
3
3
1
1
1
2
1
1
F074
68
F0
20
72
F1
F0
12
F1
F122
F0
68
10
F1
2
F1
0
FU
LL
F122
F0
68
10
F1
F1
20
FU
LL
F122
F0
68
10
F1
20
F1
LL
FU
F122
F1
0
88
8
F1
F074
RIGHT REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F068R
F068W
F071R
F071W
F072R
F072W
F074R
F074W
F110R
F110W
F112R
F112W
F120R
F120W
F122R
F122W
F180R
F180W
F181R
F181W
F188R
F188W
QTY
3
4
1
1
2
3
1
4
4
1
1
1
F181 or F071
122273-01A
www.desatech.com
19
Brick Installation
Continued
42" FULL HERRINGBONE BRICK MATRIX
F074
F0
F0
72
LL
FU
68
F0
64
F0
68
F0
72
F120
LEFT REFRACTORY
F074
LL
68
FU
F0
64
F0
LL
FU
F120
68
LL
F0
FU
64
F0
LL
FU
F120
63
69
F1
F1
F176
64
F0
LL
FU
F120
F175 or F182
F177
RED
FULL
(112140-01)
IVORY
FULL
(112140-05)
QTY
6
F064R
F068R
F072R
F074R
F120R
F163R
F169R
F175R
F176R
F177R
F182R
F064W
F068W
F072W
F074W
F120W
F163W
F169W
F175W
F176W
F177W
F182W
4
4
2
2
4
1
1
1
1
1
1
F074
F074
72
F0
68
F0
72
89
F0
F0
72
F0
LL
63
F0
LL
FU
FU
REAR REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
QTY
9
LL
LL
FU
72
F0
LL
FU
FU
LL
63
F0
LL
FU
FU
72
F0
LL
FU
63
F0
F0
61
8
6
F1
8
7
F1
61
72
F1
LL
FU
F1
F063R
F068R
F072R
F074R
F089R
F161R
F063W
F068W
F072W
F074W
F089W
F161W
3
1
6
2
1
2
F168R
F168W
1
F171R
F171W
1
F178R
F178W
1
F171
F074
F0
72
8
6
F0
2
7
F0
1
0
F1
LL
LL
FU
00
F1
LL
66
FU
FU
F0
RIGHT REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
66
F0
FU
LL
LL
FU
LL
FU
0
0
F1
66
F0
FU
LL
LL
FU
FU
0
0
F1
LL
66
F0
65
F1
64
F1
4
7
F1
F068R
F071R
F072R
F074R
F100R
F101R
F162R
F164R
F165R
F174R
F068W
F071W
F072W
F074W
F100W
F101W
F162W
F164W
F165W
F174W
QTY
9
1
4
2
1
3
1
1
1
1
1
F162 or F184
20
www.desatech.com
122273-01A
Brick Installation
Continued
50" FULL HERRINGBONE BRICK MATRIX
F074
72
F0
FU
68
F0
64
F0
68
F0
72
F0
F120
LEFT REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F074
LL
LL
FU
68
F0
64
F0
LL
FU
F120
LL
68
F0
FU
64
F0
LL
FU
F120
63
F1
69
F1
F176
64
F0
LL
FU
F120
F175 or F182
F177
F074
F074
82
F0
68
F0
72
F0
68
F0
72
F0
89
F0
F0
LL
65
FU
LL
FU
LL
LL
FU
FU
63
F0
F0
LL
65
FU
LL
FU
FU
LL
LL
FU
63
F0
F0
LL
LL
65
FU
FU
LL
FU
LL
FU
63
F0
F168
F178
F074
F093
F074
68
F0
68
F0
72
85
F0
F0
F0
84
LL
FU
83
F0
FU
FU
LL
FU
84
F0
LL
LL
83
F0
FU
84
F0
LL
FU
LL
FU
LL
8
F0
3
84
F0
LL
FU
or
72
F1 183
F
LL
FU
F1
73
122273-01A
F167
F166
70
61
F1
F1
61
F1
F168
QTY
6
F064R
F068R
F072R
F064W
F068W
F072W
4
4
2
F074R
F120R
F163R
F169R
F175R
F176R
F074W
F120W
F163W
F169W
F175W
F176W
2
4
1
1
1
1
F177R
F182R
F177W
F182W
1
1
REAR REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F063R
F063W
F065R
F065W
F068R
F068W
F072R
F072W
F074R
F074W
F082R
F082W
QTY
12
3
3
2
2
2
1
F089R
F089W
1
F161R
F161W
2
F168R
F168W
2
F170R
F170W
1
F178R
F178W
1
RIGHT REFRACTORY
RED
IVORY
FULL
FULL
(112140-01)
(112140-05)
F068R
F072R
F074R
F083R
F084R
F085R
F093R
F166R
F167R
F172R
F173R
F183R
www.desatech.com
F068W
F072W
F074W
F083W
F084W
F085W
F093W
F166W
F167W
F172W
F173W
F183W
QTY
9
2
1
2
3
4
1
1
1
1
1
1
1
21
BRICK Installation
Continued
36" SPLIT STACKED BRICK MATRIX
FULL
S047
S046
FULL
FULL
FULL
S047
FULL
FULL
S047
FULL
FULL
FULL
FULL
S047
FULL
S044 or S095 S043
S045
FULL
S049
FULL
FULL
FULL
S049
FULL
S049
FULL
S049
FULL
S049
FULL
S051
S046
S050
FULL
FULL
S046
S050
FULL
FULL
S046
S050
FULL
S046
S047
S047
S047
FULL
FULL
FULL
S046
S047
FULL
FULL
S050
S048
FULL
FULL
S047
FULL
FULL
S054
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
17
(112140-02) (112140-06)
S048R
S048W
12
S049R
S049W
10
S051R
S051W
1
S052R
S052W
2
S052
FULL
FULL
S046
S050
S048
FULL
FULL
S052
S048
FULL
FULL
S049
S048
FULL
FULL
S049
S048
FULL
FULL
S049
S048
S049
FULL
S049
S048
LEFT REFRACTORY
RED
IVORY QTY
FULL
FULL
16
(112140-02) (112140-06)
S043R
S043W
1
S044R
S044W
1
S045R
S045W
1
S046R
S046W
6
S047R
S047W
6
S050R
S050W
5
S095R
S095W
1
S046
FULL
S048
S050
FULL
S047
S048
S050
S046
FULL
S048
S050
S046
FULL
S048
S050
S046
FULL
S047
S048
S050
S046
S047
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
16
(112140-02) (112140-06)
S044R
S044W
1
S045R
S045W
1
S046R
S046W
6
S047R
S047W
6
S050R
S050W
5
S054R
S054W
1
S095R
S095W
1
S045
S044 or S095
22
www.desatech.com
122273-01A
Brick Installation
Continued
42" SPLIT STACKED BRICK MATRIX
S077
FULL
S076
S046
FULL
S077
S077
S046
FULL
S046
FULL
S077
S046
FULL
S077
S076
S046
FULL
S076
FULL
FULL
S077
S076
S077
FULL
FULL
S077
S076
S076
S076
FULL
S076
FULL
S050
FULL
FULL
FULL
S050
FULL
FULL
FULL
S050
FULL
FULL
FULL
S050
S082
122273-01A
S045 or S081
S077
S077
S076
FULL
FULL
S046
S077
S076
FULL
S046
S050
S077
S076
FULL
FULL
S046
S078
S076
FULL
S046
S050
S077
S051
FULL
S046
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
16
(112140-02) (112140-06)
S051R
S051W
2
S076R
S076W
12
S077R
S077W
10
S078R
S078W
2
S076
FULL
S051
S078
S077
FULL
FULL
S076
S077
FULL
FULL
S077
S077
FULL
FULL
S076
S077
S076
FULL
FULL
S077
S080
S076
FULL
S076
LEFT REFRACTORY
RED
IVORY
QTY
FULL
FULL
17
(112140-02) (112140-06)
S045R
S045W
1
S046R
S046W
5
S050R
S050W
6
S076R
S076W
6
S077R
S077W
6
S080R
S080W
1
S081R
S081W
1
S050
FULL
S045
or S081
S076
S050
FULL
FULL
S077
S050
FULL
FULL
S076
S050
FULL
FULL
S076
S050
FULL
FULL
S076
S050
FULL
FULL
S077
S076
FULL
S077
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
17
(112140-02) (112140-06)
S045R
S045W
1
S046R
S046W
5
S050R
S050W
6
S076R
S076W
6
S077R
S077W
6
S081R
S081W
1
S082R
S082W
1
S076
www.desatech.com
23
brick Installation
Continued
50" SPLIT STACKED BRICK MATRIX
S076
FULL
S076
S077
FULL
FULL
FULL
FULL
FULL
FULL
FULL
FULL
FULL
S049
S048
S048
S048
S050
FULL
S050
S054
24
S076
FULL
S076
S077
FULL
S076
FULL
FULL
S077
FULL
FULL
S095
S077
FULL
FULL
S046
S077
FULL
FULL
S046
S077
S076
FULL
S046
S050
FULL
FULL
S046
S048
S052
S076
FULL
S046
S050
FULL
S051
FULL
S048
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
28
(112140-02) (112140-06)
S048R
S048W
12
S049R
S049W
10
S051R
S051W
2
S052R
S052W
2
S049
FULL
S046
S050
FULL
FULL
S051
S048
S049
FULL
FULL
S052
FULL
FULL
FULL
S048
S049
FULL
FULL
S049
FULL
FULL
FULL
S048
S049
FULL
FULL
S049
S048
FULL
FULL
FULL
LEFT REFRACTORY
RED
IVORY
QTY
FULL
FULL
16
(112140-02) (112140-06)
S043R
S043W
1
S045R
S045W
1
S046R
S046W
6
S050R
S050W
5
S076R
S076W
6
S077R
S077W
6
S095R
S095W
1
S096R
S096W
1
S049
FULL
FULL
S048
FULL
FULL
FULL
S049
S043
S095
S077 S045 or S096
S048
S050
S046
FULL
FULL
S050
S046
FULL
S076
S049
S050
S046
FULL
S076
S048
S046
FULL
S076
S077
S050
FULL
FULL
S077
S050
S046
FULL
S076
S077
S046
FULL
FULL
S077
S076
S045 or S096
S077
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
16
(112140-02) (112140-06)
S045R
S045W
1
S046R
S046W
6
S050R
S050W
5
S054R
S054W
1
S076R
S076W
6
S077R
S077W
6
S095R
S095W
1
S096R
S096W
1
www.desatech.com
122273-01A
brick Installation
Continued
36" SPLIT HERRINGBONE BRICK MATRIX
S003
S0
02
FU
LL
FU
LL
FU
LL
FU
LL
FU
LL
S0
72
69
S0
S0
74
69
S0
LL
2
FU
03 03
S1 r S
o
FU
LL
69
S0
LL
FU
F120
S073
S003
S003
90
02
S0
14
14
S0
14
S0
14
S0
FU
14
FU
LL
14
S0
LL
FU
FU
LL
S0
LL
S0
FU
FU
LL
14
LL
S0
FU
FU
LL
04
91
S0
S0
01
S0
01
S0
S0
F1
94
S0
58
S0
58
S0
58
S0
58
69
S0
LL
FU
S0
58
69
S0
LL
FU
S0
58
69
S0
LL
FU
S0
58
69
S0
LL
FU
S0
75
71
S0
01
S0
04
S0
LEFT REFRACTORY
RED
IVORY
QTY
FULL
FULL
12
(112140-02) (112140-06)
S001R
S001W
1
S002R
S002W
1
S003R
S003W
1
S004R
S004W
1
S032R
S032W
1
S058R
S058W
7
S069R
S069W
7
S071R
S071W
1
S072R
S072W
1
S073R
S073W
1
S074R
S074W
1
S075R
S075W
1
S103R
S103W
1
F120R
F120W
1
F194R
F194W
1
LL
S0
14
S0
LL
FU
LL
S0
FU
FU
LL
14
S0
62
14
S0
S0
1
S0
59
7
F0
S0
14
15
S0
61
FU
LL
14
F129
F120
S003
57
S0
S0
55
S0
55
S0
55
S0
55
55
S0
66
FU
55
S0
S0
or
67
68
S0
S0
56
S0
65
S0
63
58
LL
F129
S0
FU
S0
LL
LL
58
FU
122273-01A
S0
FU
LL
58
LL
FU
S0
FU
LL
58
LL
FU
S0
FU
LL
8
LL
FU
5
S0
FU
LL
LL
FU
58
S0
FU
LL
04
S0
S0
55
93
F1
01
S0
S0
02
S064
F130
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
12
(112140-02) (112140-06)
S001R
S001W
2
S002R
S002W
1
S003R
S003W
2
S004R
S004W
1
S014R
S014W
12
S015R
S015W
1
S059R
S059W
1
S061R
S061W
1
S062R
S062W
1
S090R
S090W
1
S091R
S091W
1
F071R
F071W
1
F120R
F120W
1
F129R
F129W
1
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
(112140-02) (112140-06)
12
S001R
S001W
1
S002R
S002W
1
S003R
S003W
1
S004R
S004W
1
S055R
S055W
7
S056R
S056W
1
S057R
S057W
1
S058R
S058W
6
S063R
S063W
1
S064R
S064W
1
S065R
S065W
1
S066R
S066W
1
S067R
S067W
1
S068R
S068W
1
F129R
F129W
1
F130R
F130W
1
F193R
F193W
1
www.desatech.com
25
brick Installation
Continued
42" SPLIT HERRINGBONE BRICK MATRIX
S003
02
S0
LL
S085
S085
FU
LL
LL
LL
S0
FU
FU
FU
FU
LL
77
S085
FU
S0
F1
3
1
03
7
F0
75
S085
S0
S1
02
LL
S0
LL
FU
FU
02
LL
S0
FU
S085
LL
FU
FU
02
LL
LL
S0
FU
FU
02
LL
LL
S0
FU
FU
02
LL
S0
S085
LL
FU
FU
02
LL
S0
S085
LL
FU
FU
02
LL
04
S0
S0
01
01
02
S0
S0
S087
LL
S003
1
F054 or S088
S003
S003
02
S0
02
74
S0
74
S0
74
S0
74
S0
S0
59
S0
S0
74
S0
FU
84
86
S0
S0
02
S0
0
2
F054
02
S0
S0
02
02
S0
S0
02
02
LL
LL
LL
LL
LL
LL
04
S1
65
S0
74
LL
FU
LL
FU
S092 or S093
S0
2
S0
0
FU
FU
FU
FU
FU
LL
FU
LL
FU
FU
LL
FU
LL
S0
LL
FU
FU
S094
26
LL
LL
S089
FU
FU
S089
LL
LL
FU
S089
FU
LL
FU
S089
S003
01
S0
04
S0
04
S0
S089
1
0
S0
S089
71
F0
60
S0
62
61
S0
S0
LL
04
S0
FU
74
LL
LL
FU
04
S0
FU
LL
LL
FU
04
S0
FU
LL
LL
FU
04
S0
FU
LL
LL
FU
04
S0
FU
LL
LL
FU
04
S0
FU
LL
04
S0
S0
01
S0
83
S0
01
S0
S003
S089
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
12
(112140-02) (112140-06)
S001R
S001W
2
S002R
S002W
2
S003R
S003W
2
S004R
S004W
7
S059R
S059W
1
S060R
S060W
1
S061R
S061W
1
S062R
S062W
1
S071R
S071W
1
S074R
S074W
6
S083R
S083W
1
S084R
S084W
1
F120R
F120W
1
F129R
F129W
1
F129
F120
S089
LEFT REFRACTORY
RED
IVORY
QTY
FULL
FULL
12
(112140-02) (112140-06)
S001R
S001W
1
S002R
S002W
1
S003R
S003W
1
S004R
S004W
1
S032R
S032W
1
S058R
S058W
7
S069R
S069W
7
S071R
S071W
1
S072R
S072W
1
S073R
S073W
1
S074R
S074W
1
S075R
S075W
1
S103R
S103W
1
F056R
F056W
1
F120R
F120W
1
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
18
(112140-02) (112140-06)
S001R
S001W
2
S002R
S002W
8
S003R
S003W
2
S004R
S004W
2
S065R
S065W
1
S074R
S074W
1
S086R
S086W
1
S089R
S089W
8
S092R
S092W
1
S093R
S093W
1
S094R
S094W
1
S104R
S104W
1
F054R
F054W
2
F054
www.desatech.com
122273-01A
brick Installation
Continued
50" SPLIT HERRINGBONE BRICK MATRIX
S003
S0
9
7
7
7
S0
9
7
7
7
02
S0
LL
02
S0
FU
FU
LL
12
LL
LL
FU
FU
LL
LL
FU
FU
LL
LL
FU
FU
LL
LL
FU
FU
LL
LL
FU
FU
60
S0
S0
62
59
08
S0
60
06
S0
S0
S0
LL
FU
LL 9
FU 05
S
02
S0
LL
S007
FU
FU
LL
FU
S007
LL
FU
FU
LL
FU
LL
FU
S007
3
0
S1
1
7
S088 or F054
S0
6
LL
0
S1
S007
7
LL
FU
LL
FU
LL
FU
S007
FU
1
7
0
S1
LL
FU
01
S1
LL
FU
01
S1
LL
FU
FU
LL
LL
01
S1
S007
FU
01
S1
LL
FU
01
S007
FU
LL
LL
4
S1
S0
6
F195
LL
02
S0
0
S0
01
S0
08
S1
S0
9
REAR REFRACTORY
RED
IVORY
QTY
FULL
FULL
(112140-02) (112140-06) 24
S001R
S001W
2
S002R
S002W
2
S003R
S003W
2
S004R
S004W
2
S006R
S006W
13
S008R
S008W
1
S012R
S012W
1
S059R
S059W
2
S060R
S060W
2
S062R
S062W
2
S100R
S100W
1
F129R
F129W
3
F136R
F136W
1
F129
S003
S0
75
S0
06
S0
06
S0
06
S0
06
LL
S0
06
LL
FU
FU
00
S0
S0
06
LL
06
S0
LL
FU
FU
S0
06
LL
S102
S0
LL
FU
FU
06
06
LL
F129
S003
122273-01A
S0
LL
FU
FU
S0
06
S0
LL
LL
S1
36
04
FU
FU
F129
F1
01
S0
04
06
S003
S0
S0
01
S0
S0
7
S0
9
F1
3
7
S0
6
5
F120
S003
62
7
6
S0
0
0
S1
LL
FU
LL
S0
0
FU
LL
LL
S0
9
FU
LL
S0
0
FU
LL
LL
S0
9
FU
LL
S0
0
FU
LL
LL
FU
LL
S0
0
FU
LL
LL
S0
9
FU
LL
S0
0
FU
LL
LL
S0
9
FU
LL
S0
0
FU
LL
04
0
S1
S093 or S099
F130
LEFT REFRACTORY
RED
IVORY
QTY
FULL
FULL
(112140-02) (112140-06) 18
S001R
S001W
2
S002R
S002W
1
S003R
S003W
2
S004R
S004W
2
S007R
S007W
8
S067R
S067W
1
S093R
S093W
1
S097R
S097W
6
S098R
S098W
1
S099R
S099W
1
S105R
S105W
1
S106R
S106W
1
F120R
F120W
1
F130R
F130W
1
F137R
F137W
1
8
S0
02
7
FU
S0
0
7
7
7
7
7
FU
04
FU
S0
FU
01
S0
FU
01
S0
S0
FU
7
S003
F139
RIGHT REFRACTORY
RED
IVORY
QTY
FULL
FULL
(112140-02) (112140-06( 18
S001R
S001W
1
S002R
S002W
2
S003R
S003W
2
S004R
S004W
1
S007R
S007W
7
S067R
S067W
2
S075R
S075W
1
S088R
S088W
1
S093R
S093W
1
S101R
S101W
7
S102R
S102W
1
S107R
S107W
1
S108R
S108W
1
F054R
F054W
1
F139R
F139W
1
F195R
F195W
1
www.desatech.com
27
Brick Installation
Continued
Grouting instructions
Material provided:
1 or 2 - 10 lb. bags of cement (depending
on model)
1 or 2 - 10 lb. bags of sand (depending
on model)
Material required:
1 - Piping bag
1 - Joints striker
1 - Heavy duty mixing bucket
1 - Trowel
1. Moisten brick surface with damp sponge
or spray bottle just prior to application.
When bricks are wet, any excess grout
mixture on bricks will easily wipe off.
2. In a heavy duty mixing bucket, pour seven
(7) cups of water. Add 5 lbs. (half of a bag)
of sand and 5 lbs (half of a bag) of cement.
Mix together well using a power drill with
mixing wand attachment.
3. The overall length of piping bag should be
about 16". If the bag is longer than 16",
cut it down to size by removing end with
larger opening. This will make the bag
easier to handle.
4. Put 2 to 3 cups of grout mixture into piping
bag making sure the smaller opening is
downward and over a moist towel to avoid
spilling. Place a wet towel over the bucket
making sure it is directly on the surface of
grout mixture. This will keep the mixture
moist and it will not dry out before use.
5. Begin grouting by first doing a “Filler
Pass”. This is done by filling the joint about
3/4 full with grout mixture. It is important
to work with only 6 bricks at a time so
grout doesn't have time to set up before
striking.
6. Complete a “Finishing Pass” around 6
bricks you just put filler pass around. This
is done by slowly filling in remainder of the
joint with a thick amount of grout mixture.
Mixture should be a little higher than the
brick surface.
7. Using a trowel, remove excess grout mixture by moving trowel in the direction of the
joint. Grout mixture in the joint should now
be flush with brick surface.
28
8. Using a joint striker, force grout mixture
into joint and sweep back and forth
until grout is smooth and round. If grout
becomes too shallow, add more grout
mixture with piping bag and strike again.
9. Continue procedure around each group of
6 bricks until an entire panel is finished.
10.Using trowel, scrape in direction of joints
to remove any grout that may have collected around bricks during striking. If
desired, take a moist sponge and lightly
sweep over bricks to remove any grout
that may have gotten on bricks. DO NO
PRESS HARD OR RUB IN A CIRCULAR
MOTION. This will press the grout into
brick and turn brick a different color.
Allow 72 hours before
operating fireplace.
Figure 25 - Grouting Brick
www.desatech.com
122273-01A
Brick Installation
Continued
INSTALLING FIREPLACE SCREEN
1. Mount screen rod brackets on left and right
side of smoke shelf with #8 x 1/2" screws
provided (see Figure 26).
2. Slide round end of screen rod into rings
at top of screen. Attach one push-on nut
to end of rod before attaching last ring of
screen.
3. Insert round end of rod into rod bracket
on left side of fireplace.
4. Mount flat end of screen rod with #10 x 5/8"
to center of smoke shelf (see Figure 26).
5. Install other screen rod in same manner.
Screen
Rod
Bracket
Fireplace Front
Smoke Shelf
Push
On Nut
Screen
Rod
Ring
Screen
Figure 26 - Installing Fireplace Screen
Glass Door Installation
door frame MODELS
BDMO36E/G/C, BDMO42E/G/C AND
BDMO50E/G/C
Installation
1. Remove screws from smoke shelf (see
Figure 27).
2. Mount top door frame and secure with
screws provided (see Figure 27).
3. Place bottom door frame on top of ash lip
at front of fireplace (see Figure 28).
Top Door
Frame
Smoke
Shelf
4. Using a 7/16" open end or adjustable
wrench, secure bottom door frame to
brick with two hex screws provided (see
Figure 28).
Ash Lip
Bottom
Door
Frame
Ash Lip
Hex
Screw
Figure 28 - Installing Bottom Door Frame
Figure 27 - Installing Top Door Frame
122273-01A
www.desatech.com
29
Glass Door Installation
Continued
Installing glass doors
Door Adjustment
Spring clips have been installed. Some adjustments may be needed. Install doors using the
following steps:
1. With bifold doors completely folded, insert
bottom pivot pin into pivot hole located
near bottom corner of front face opening
and swing door to vertical position making
sure top pins slide into door track. Door
is installed when top door pin snaps into
spring clip.
2. Repeat step 1 for remaining door.
If you find the doors do not close properly or
do not appear level or straight, proceed with
section on door adjustment,
Remove doors and slightly loosen lower pivot
clips and upper spring clips. Replace doors
and fully close them. Use 1/8" shims (any
material) to level doors. Once proper setting
is achieved, carefully open doors enough so
that you can access spring clips with a phillips
screwdriver. Tighten screws. See Figure 30.
Fold Door
and Slide
Top Pins
Into Track
Spring
Clip
Insert Pin
into Spring
Clip
Figure 30 - Adjusting Bi-Fold Doors
Insert
Bottom
Pivot Pin
into Hole
Pivot
Hole
Figure 29 - Installing Bi-Fold Doors
30
www.desatech.com
122273-01A
Operation and Maintenance Guidelines
Glass Doors
Glass doors are optional with the fireplace.
When fireplace is in operation, doors must be
fully opened or fully closed position only or a
fire hazard may be created (see Figure 31).
A fireplace equipped with glass doors operates much differently than a fireplace with an
open front. A fireplace with glass doors has a
limited amount of air for combustion.
Excessive heat within the fireplace can result
if too large a fire is built or if combustion air
gate is not completely open. The following
tips should be followed to assure that both
the fireplace and glass door retain their beauty
and function properly. Both the flue damper
and glass doors must be fully opened before
starting fire. This will provide sufficient combustion air and maintain safe temperatures
in firebox.
IMPORTANT: The glass must be allowed to
warm slowly and evenly. The tempered glass
will withstand a gradual temperature rise to
550° F, which is more than a normal fire will
generate. Such materials as pitch/wax laden
logs, very dry mill end lumber and large
amounts of paper or cardboard boxes can
create an excessively hot fire and should not
be burned in this fireplace. Always keep the
fire well back from the doors and never allow
flames to contact the glass.
WARNING: Fireplaces
equipped with glass doors
should be operated only with
doors fully opened or doors fully
closed. Doors, if left partly open,
may draw gas and flame out of
the fireplace opening creating
risks of both fire and smoke.
122273-01A
Cleaning Glass
Clean glass with any commercial glass
cleaner or soap and water. Do not use any
abrasive material to clean glass. Do not clean
glass with any cool water if glass is still hot
from the fire and smoke.
A gas line or gas log lighter may be installed
for the purpose of installing a vented or ventfree decorative gas appliance incorporating an
automatic shutoff device and complying with
the Standard for Decorative Gas Appliances
for Installation in Vented Fireplaces, ANSI
Z21.60 or American Gas Association draft
requirements for Gas Fired Log Lighters for
Wood Burning Fireplaces, Draft NO. 4 dated
August, 1993.
If you wish to install an unvented (vent-free)
gas log set, only unvented gas log sets which
have been found to comply with the standard
for unvented room heaters, ANSI Z21.11.2 are
to be installed in this fireplace.
Doors Fully Closed
Fireplace Front
Doors
Fully Opened
Fireplace Front
Figure 31 - Bi-Fold Glass Doors
www.desatech.com
31
Operation and Maintenance Guidelines
Continued
outside air and damper
handle operation
The damper handle, which opens and closes
the damper blade, is located in the upper front
face of the fireplace. Pushing the handle forward and up through the keyway slot will free
damper blade to automatically open. Pushing
the handle forward and down will lock damper
blade closed (see Figure 32).
Damper
Weight
The outside air kit lever is located at the left
and right hand sides of fireplace (see Figure
33). Lifting lever up will free the outside air
door to open. Pulling lever down will lock
the door.
WARNING: Risk of fire!
Replace grate with DESA Heating, LLC grate only (see Parts,
page 35). This grate has been
designed to keep the operation of your fireplace safe and
efficient.
Open Position
Closed Position
To Close
Damper
Damper
Weight
Figure 33 - Outside Air Kit Lever
To Open
Damper
Figure 32 - Operating Damper Handle
32
www.desatech.com
122273-01A
Technical Service
You may have further questions about installation, operation, or troubleshooting. If so, contact DESA Heating, LLC at 1-866-672-6040.
When calling please have your model and serial numbers of your heater ready.
You can also visit DESA Heating, LLC’s web
site at www.desatech.com.
Replacement Parts
Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
Parts Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040.
When calling DESA Heating, LLC, have
ready
• your name
• your address
• model and serial numbers of your firebox
• how firebox was malfunctioning
• type of gas used (propane/LP or natural
gas)
• purchase date
Usually, we will ask you to return the part to
the factory.
122273-01A
Parts Not Under Warranty
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040 for
referral information. A list of authorized dealers
can be found by visiting www.desatech.com.
When calling DESA Heating, LLC, have
ready
• model number of your firebox
• the replacement part number
www.desatech.com
33
Parts
Models (V)Jm36(Sr,SI,HR,HI), (V)Jm42(Sr,SI,HR,HI), (V)Jm50(Sr,SI,HR,HI),
WCM-36J, WCM-42J, WCM-50J
11
9
8
7
10
6
12
13
24
25
19
15
5
14
26 28
1
17/18
22
16
21
27
4
2
19
30
23
3
29
20
31
34
www.desatech.com
122273-01A
Parts
KEY
NO. PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
**
**
**
120827-01
120827-02
120827-03
**
**
**
**
**
110285-03
110285-02
110285-01
23490SA
**
109720-02
117891-01
20042
21171
109752-01
109752-02
109726-01
**
**
**
**
**
**
**
**
**
117566-03
117566-01
117566-02
117568-03
117568-01
117568-02
117544-03
117544-01
117544-02
DESCRIPTION
Face Assembly
Firebox Bottom Assembly
Firebox Bottom
Hearth Brick Panel, 36"
Hearth Brick Panel, 42"
Hearth Brick Panel, 50"
Firebox Surround
Outer Dome Assembly
Insulation Pan Support
Insulation Pan
Top Insulation
Fireplace Top Assembly, 36"
Fireplace Top Assembly, 42"
Fireplace Top Assembly, 50"
Standoff
Fireplace Surround Assembly
Clearance Spacer
Fireplace Handle Bracket
Outside Air Cover Plate
Gas Conduit Cover
Conduit One
Conduit Two
Air Duct
Heat Shield Support
Ash Box Assembly
Ash Box Ring
Hearth Support Brace
Inner Dome Assembly
Smoke Shield
Damper Control Bracket
Air Kit Door Assembly, Right
Air Kit Door Assembly, Left
Screen
Screen
Screen
Screen Rod
Screen Rod
Screen Rod
Grate
Grate
Grate
(V)JM
36, W
CM-3
(V)JM
6J
42, W
CM-4
(V)JM
2J
50, W
CM-5
0J
This list contains replaceable parts used in your firebox. When ordering parts, follow the
instructions listed under Replacement Parts on page 33 of this manual.
QTY.
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
6
4
2
4
2
2
6
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
•
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PARTS AVAILABLE NOT SHOWN
see page 36 Brick Panel Assemblies with Brick
Housings (1 each, right, left, rear)
•
•
** Not a field replaceable part.
122273-01A
www.desatech.com
35
Parts
Models (V)Jm36(Sr,SI,HR,HI), (V)Jm42(Sr,SI,HR,HI), (V)Jm50(Sr,SI,HR,HI)
36
DESCRIPTION
36" Full Stack Left Panel Assembly
42" Full Stack Left Panel Assembly
50" Full Stack Left Panel Assembly
36" Full Herringbone Left Panel Assembly
42" Full Herringbone Left Panel Assembly
50" Full Herringbone Left Panel Assembly
36" Full Stack Right Panel Assembly
42" Full Stack Right Panel Assembly
50" Full Stack Right Panel Assembly
36" Full Herringbone Right Panel Assembly
42" Full Herringbone Right Panel Assembly
50" Full Herringbone Right Panel Assembly
36" Full Stack Rear Panel Assembly
42" Full Stack Rear Panel Assembly
50" Full Stack Rear Panel Assembly
36" Full Herringbone Rear Panel Assembly
42" Full Herringbone Rear Panel Assembly
50" Full Herringbone Rear Panel Assembly
QTY.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
MK36S
S-(R
)(I)
MK36S
H-(R
)(I)
MK42S
S-(R
)
(I)
MK42S
H-(R
MK)(I)
50S
S-(R
)(I)
MK50S
H-(R
)(I)
PART NO.
122317-02
122319-02
122321-02
122323-02
122327-02
122327-02
122317-01
122319-01
122321-01
122323-01
122325-01
122327-01
122354-01
122354-02
122354-03
122356-01
122356-02
122356-03
(V)J
(V)J
M36
S(R
)(I)
M36
S(R
)(I)
(V)J
M42
H(R
)(I)
(V)J
M42
S(R
)(I)
(V)J
M50
H(R
)(I)
(V)J
M50
S(R
)(I)
This list contains replaceable parts used in your firebox. When ordering parts, follow the
instructions listed under Replacement Parts on page 33 of this manual.
PART NO.
DESCRIPTION
120842-01
120842-02
120842-03
120845-01
120845-02
120845-03
120843-01
120843-02
120843-03
120846-01
120846-02
120846-03
120844-01
120844-02
120844-03
120847-01
120847-02
120847-03
36" Split Stack Left Panel Assembly
42" Split Stack Left Panel Assembly
50" Split Stack Left Panel Assembly
36" Split Herringbone Left Panel Assembly •
42" Split Herringbone Left Panel Assembly
50" Split Herringbone Left Panel Assembly
36" Split Stack Right Panel Assembly
42" Split Stack Right Panel Assembly
50" Split Stack Right Panel Assembly
36" Split Herringbone Right Panel Assembly •
42" Split Herringbone Right Panel Assembly
50" Split Herringbone Right Panel Assembly
36" Split Stack Rear Panel Assembly
42" Split Stack Rear Panel Assembly
50" Split Stack Rear Panel Assembly
36" Split Herringbone Rear Panel Assembly •
42" Split Herringbone Rear Panel Assembly
50" Split Herringbone Rear Panel Assembly
QTY.
www.desatech.com
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
122273-01A
Accessories
BiFold Glass Masonry Door
BDMO36E - 36" Ebony
BDMO36G - 36" Pewter
BDMO36C - 36" Oiled Bronze
BDMO42E - 42" Ebony
BDMO42G - 42" Pewter
BDMO42C - 42" Oiled Bronze
BDMO50E - 50" Ebony
BDMO50G - 50" Pewter
BDMO50C - 50" Oiled Bronze
Optional Outside air kit for
floor installation - ak4f
Optional Outside Air Kit for
Sidewall Installation - AK-4
Double Wall Pipe - 12-12DM,
18-12DM, 24-12DM, 36-12DM, 48-12DM,
12-12HT, 18-12HT, 24-12HT, 36-12HT and
48-12HT
30° Offset and Return
30E-12DM and 30E-12HT
Storm Collar - SC2-1
Firestop Spacer - FS-10
(1100EFS-10DM for 36" Models)
Ember Protector - 20093
Roof Flashing
V6F-10DM - 0 to 6/12 Pitch
V12F-10DM - 6/12 to 12/12 Pitch
122273-01A
www.desatech.com
37
AccessorIES
Continued
SQUARE CHASE-TOP
TERMINATION - STL-12D
38
Round ToP TErminations
RLT-12D and RLT-12HT
www.desatech.com
122273-01A
NOTES
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
122273-01A
www.desatech.com
39
DESA Heating, LLC
2701 Industrial Drive
Bowling Green, KY 42101
www.desatech.com
1-866-672-6040
122273.01
NOT A UPC
122273-01
Rev. A
11/07
Download PDF

advertising