Installation manual | Desa (V)JM50 SERIES Outdoor Fireplace User Manual

DIRECT-VENT FIREPLACE
OWNER’S OPERATION AND
INSTALLATION MANUAL
For more information, visit www.desatech.com
NATURAL GAS MODELS (V)K36N SERIES
PROPANE/LP GAS MODEL (V)K36P SERIES
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
WARNING: Improper installation, adjustment, alteration,
service, or maintenance can
cause injury or property damage. Refer to this manual for
correct installation and operational procedures. For assistance or additional information consult a qualified
installer, service agency, or
the gas supplier.
Installation and service
must be performed by a
qualified installer, service
agency, or the gas supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance
is not convertible for use with other gases, unless a certified kit is used.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
CLEANING AND MAINTENANCE ............................................ 27
PRODUCT IDENTIFICATION ..................................................... 3
TROUBLESHOOTING .............................................................. 28
LOCAL CODES ........................................................................... 3
REPLACEMENT PARTS .......................................................... 31
PRODUCT FEATURES .............................................................. 4
SPECIFICATIONS .................................................................... 31
PRE-INSTALLATION PREPARATION ........................................ 4
SERVICE HINTS ....................................................................... 31
LOCATION OF TERMINATION CAP .......................................... 6
TECHNICAL SERVICE ............................................................. 31
VENTING INSTALLATION INSTRUCTIONS .............................. 7
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 32
FIREPLACE INSTALLATION .................................................... 16
ACCESSORIES ........................................................................ 36
OPERATING FIREPLACE ........................................................ 23
OWNER’S REGISTRATION FORM .......................................... 37
INSPECTING BURNERS .......................................................... 26
WARRANTY INFORMATION ...................................... Back Cover
SAFETY INFORMATION
Natural and Propane/LP Gas: Natural and propane/LP gases are
WARNINGS
WARNING: This product contains and/or generates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
IMPORTANT: Read this owner’s manual carefully
and completely before trying to assemble, operate, or
service this fireplace. Improper use of this fireplace
can cause serious injury or death from burns, fire,
explosions, electrical shock, and carbon monoxide
poisoning.
DANGER: Carbon monoxide poisoning may lead
to death!
This fireplace must be installed by a qualified (certified or licensed)
service person. It has a sealed gas combustion chamber that uses a
coaxial pipe (pipe within a pipe and having the same center) venting
system. It brings in fresh air for combustion through the outer pipe and
combustion gases are exhausted through the inner pipe. If the glass
door assembly and venting pipe are not properly seated, connected,
and sealed, carbon monoxide leakage (spillage) can occur.
odorless. An odor-making agent is added to the gas. The odor helps
you detect a gas leak. However, the odor added to the gas can fade.
Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this fireplace.
WARNING: Any change to this fireplace or its
controls can be dangerous.
1.
2.
3.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the fireplace may not have been installed
properly. Get fresh air at once! Have fireplace inspected and
serviced by a qualified service person. Some people are more
affected by carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
4.
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
For propane/LP fireplace, do not place propane/LP supply
tank(s) inside any structure. Locate propane/LP supply tank(s)
outdoors. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier's instructions
• if you cannot reach you gas supplier, call the fire department.
Never install the fireplace
• in a recreational vehicle
• in windy or drafty areas where curtains or other combustible
(flammable) objects can make contact with the fireplace front
• in high traffic areas
For more information, visit www.desatech.com
111923-01B
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
SAFETY INFORMATION
Continued
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
This fireplace reaches high temperatures. Keep children and
adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they are in the room
with fireplace.
Do not modify this fireplace under any circumstances. Any
parts removed for servicing must be replaced prior to operating fireplace.
Turn fireplace off and let cool before servicing, installing, or
repairing. Only a qualified service person should install, service, or repair this fireplace. Have fireplace inspected annually by a qualified service person.
You must keep control compartments, burners, and circulating air passages clean. More frequent cleaning may be needed
due to excessive lint and dust from carpeting, bedding material, etc. Turn off the gas valve and pilot light before cleaning
fireplace.
Have venting system inspected annually by a qualified service
person. If needed, have venting system cleaned or repaired.
See Cleaning and Maintenance, page 27.
Keep the area around your fireplace clear of combustible materials, gasoline, and other flammable vapor and liquids. Do
not run fireplace where these are used or stored. Do not place
items such as clothing or decorations on or around fireplace.
Do not use this fireplace to cook food or burn paper or other
objects.
Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this fireplace. Use only the gas type indicated on fireplace
nameplate.
This appliance, when installed, must be electrically grounded
in accordance with local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
Do not use fireplace if any part has been exposed to or under
water. Immediately call a qualified service person to arrange
for replacement of the unit.
Do not operate fireplace if any log is broken.
Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this fireplace.
Do not operate fireplace with glass door removed, cracked, or
broken.
Provide adequate clearances around air openings.
PRODUCT IDENTIFICATION
Upper Louver
Panel
Flue Collar
Nailing
Flange
Log
Set
Glass
Door
Assembly
Lava
Rock
Lower
Louver
Panel
Control
Valve with
Piezo Ignitor
Glowing
Embers
Burner
Assembly
Switch Bracket for
Optional Remote and
Blower
Figure 1 - Direct-Vent Fireplace with Millivolt Ignition
LOCAL CODES
Install and use fireplace with care. Follow all local codes. In the
absence to local codes, use the current National Fuel Gas Code
ANSI Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Installation Code (Canada).
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
For more information, visit www.desatech.com
111923-01B
3
3
4
PRODUCT FEATURES
PRE-INSTALLATION PREPARATION
Location and Space Requirements
PRODUCT FEATURES
These are a few facts that can help you understand and enjoy your
direct-vent fireplace:
• The venting system may be routed to the outside of your home
in several ways. It may vent through the roof (vertical) or it may
vent to an outside/exterior wall (horizontal). The vent pipe installation is very important to allow for proper operation. You
must follow the venting instructions very carefully for either
vertical or horizontal applications.
• This fireplace may be installed in any room of your house provided
all local codes and these installation instructions are followed.
• This fireplace requires a wall switch, hand-held remote or wall
thermostat (millivolt) for operation (see Accessories, page 36).
• This fireplace does not require electricity to operate.
• Only the blower requires electricity if installed and if you plan
to install the blower at a later date, do not forget to wire the
outlet at the bottom of the fireplace when framing.
• A piezo ignitor and ceramic electrode create spark to ignite the
pilot light. It does not require any matches, batteries or any other
sources of ignition to light the pilot.
• Each time you turn on your fireplace, you may notice some
amount of condensation on the inside of the fireplace glass. This
is normal and will disappear after 10-20 minutes of operation.
• Your direct-vent gas fireplace system (fireplace and venting) is a
balanced and sealed gas operating unit. It requires approximately
10-20 minutes of operating time before the flame pattern stabilizes.
• Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against
any exterior surface on the back, sides, or top of your fireplace,
except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be
placed directly against wall or framing material. See framing
details on page 5.
• If you plan on installing a television or entertainment center recessed above your fireplace, it is recommended that you maintain a minimum 18" above top of louver opening.
• When locating termination cap, it is important to observe the
minimum clearances shown in Figure 7, page 6.
• If recessing into a wall, you can avoid extra framing by positioning your fireplace against an already existing framing member.
• Do not recess termination cap into a wall or siding.
• You may paint the termination cap with 450ºF (232ºC) heatresistant paint to coordinate with the exterior finish.
• There must not be any obstruction such as bushes, garden sheds,
fences, decks, or utility buildings within 24" from the front of
the termination cap.
• Do not locate termination cap where excessive snow or ice
build up may occur. Be sure to clear vent termination area after snow falls to prevent accidental blockage of venting system. When using snow blowers, do not direct snow towards
vent termination area.
PRE-INSTALLATION
PREPARATION
LOCATION AND SPACE REQUIREMENTS
Determine the safest and most efficient location for your DESA
direct-vent fireplace. Make sure that rafters and wall studs are not
in the way of the venting system. Choose a location where the heat
output is not affected by drafts, air conditioning ducts, windows or
doors. Figure 2 shows some common locations. Be aware of all
restrictions and precautions before deciding the exact location for
your fireplace and termination cap.
When deciding the location of your fireplace, follow these rules:
• Do not connect this fireplace venting to a chimney flue serving
a separate solid-fuel burning fireplace or appliance.
• Due to high temperatures, do not locate this fireplace in high traffic areas, windy or drafty areas, or near furniture or draperies.
• Proper clearances must be maintained.
• If your fireplace is to be installed directly on carpeting, vinyl
tile, or any combustible material other than wood, it must be
installed on a metal or wood panel extending the full width and
depth of the fireplace. See Figure 3.
Flush with a wall
Through exterior wall
enclosed in a chase
Corner
installation
Figure 2 - Common Fireplace Locations
29"
RW
1
21D/8"
41"
FW
Figure 3 - Fireplace Bottom Dimensions
For more information, visit www.desatech.com
111923-01B
PRE-INSTALLATION PREPARATION
Clearances
Framing and Finishing
5
5
PRE-INSTALLATION
PREPARATION
Continued
CLEARANCES
Minimum clearances to combustibles for the fireplace are as follows:
Back, and sides
0"/mm
Perpendicular walls
6" (152mm)
Floor
0"/mm
Ceiling to louver opening 42" (1067mm)
Front
36" (914mm)
Top of Standoffs
0"/mm
Vent
(See venting instructions for
specific venting clearances.)
Combustible material with a maximum thickness of 5/8" may be
flush with the top front of fireplace .
NOTICE: This fireplace is intended for use as supplemental heat. Use this fireplace along with your primary heating system. Do not install this fireplace as
your primary heat source. If you have a central heating system, you may run system’s circulating blower
while using fireplace. This will help circulate the heat
throughout the house. In the event of a power outage,
you can use this fireplace as a heat source.
15"
B
D 3/8"
10
49C5/8"
A 3/4"
35
13 3/4"
E
F
41"
41
G 1/4"
Nailing Tabs
68H 1/2"
Figure 5 - Framing Clearances for Corner Installation
1
2
3
A
4
B
FRAMING AND FINISHING
For available accessories for this fireplace, see Accessories on
page 36. If you are using a separate combustible mantel piece,
refer to Figure 6 for proper installation height. You can install
noncombustible mantels at any height above the fireplace.
Note: Noncombustible mantels may discolor!
5
C
Figure 4 shows typical framing of this fireplace. Figure 5 shows
framing for corner installation. All minimum clearances must be met.
Wall
6
D
E
7
F
G
Top of Louver Opening
Ref. Mantel Depth Ref. Mantel from Top
of Louver Opening
1
2
3
4
5
6
7
36 1/8"
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
2" (51mm)
A
B
C
D
E
F
G
16" (406mm)
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
Figure 6 - Clearances for Combustible Mantels
41 1/4"
23 1/2"
Figure 4 - Framing Clearances for Installation Against an Exterior
Wall
For more information, visit www.desatech.com
111923-01B
6
LOCATION OF TERMINATION CAP
LOCATION OF TERMINATION CAP
N
N
D
H
V
L
E
B
C
Fixed
Closed
F
B
Openable Fixed
Closed
V
Openable
V
I
V
G
B
V
B
B
J
X
V
G
G
M
A
V
K
X
V
A
V TERMINATION CAP
A = clearance above grade, veranda, porch, deck, or balcony
[*12 inches (30.5mc) minimum]
B = clearance to window or door that may be opened
[12 inches (30.5cm) minimum]
C = clearance to permanently closed window [minimum 12 inches
(30.5cm) recommended to prevent condensation on window]
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (61cm) from the
center-line of the terminal [18 inches (45.7cm) minimum]
E = clearance to unventilated soffit [12 inches (30.5cm) minimum]
F = clearance to outside corner (see below)
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly within
36 inches (91.4cm) horizontally from the center-line of the regulator
I =
J =
K =
L =
M=
N =
G GAS METER
RESTRICTED AREA
(TERMINATION PROHIBITED)
clearance to service regulator vent outlet [*72 inches (182.9cm)
minimum]
clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other fireplace [*12 inches (30.5cm)
minimum]
clearance to a mechanical air supply inlet [*72 inches (182.9cm)
minimum]
clearance above paved side-walk or a paved driveway located on
public property [*84 inches (213.3cm) minimum]
clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ]
clearance above a roof shall extend a minimum of 24 inches (61cm)
above the highest point when it passes through the roof surface and
any other obstruction within a horizontal distance of 18 inches (45.7cm)
X AIR SUPPLY INLET
vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
*
as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.
Note: Local codes or regulations may require different clearances
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Inside Corner
Outside Corner
Recessed Location
D
C
A
C
A = 6" (15.2cm)
E
V
V
V
B = 6" (15.2cm)
B
Balcony with No Side Wall
Balcony with Perpendicular Side Wall
H
G
V
V
J
G = 12" (30.5cm) minimum clearance
Combustible &
Noncombustible
H = 24" (61cm)
J = 20" (50.8cm)
C = Maximum depth of 48" (121.9cm) for
recessed location
D = Minimum width for back wall of
recessed location Combustible - 38" (965mm)
Noncombustible - 24" (61cm)
E = Clearance from corner in
recessed locationCombustible - 6" (15.2cm)
Noncombustible - 2" (5.1cm)
Figure 7 - Minimum Clearances for Termination Cap
For more information, visit www.desatech.com
111923-01B
VENTING INSTALLATION INSTRUCTIONS
Installation Precautions
7
7
VENTING INSTALLATION
INSTRUCTIONS
NOTICE: Read these instructions completely before attempting installation.
These models are tested and approved for use with DESA (directvent) pipe components and terminations.
The venting system must terminate on the outside of the structure and
can not be attached to a chimney or flue system serving a separate
solid fuel or gas burning appliance. A direct-vent appliance must have
its own venting system. DO NOT common vent this appliance.
These models are approved to be vented either horizontally through
an outside wall or vertically through a roof or chase enclosure using
the following guidelines:
• When venting system terminates horizontally on an outside wall,
you must install a standoff if the termination cap is to be installed directly on a combustible finish such as vinyl, wood,
stucco, etc.
• Never run the vent downward as this may cause excessive temperatures which could cause a fire.
• Vent pipe air space clearances to combustibles are 1" on all sides
except on the horizontal sections, which requires 2" clearance
from the top of the pipe. Where the termination cap penetrates a
combustible wall, 1" air space clearance is required.
• Snorkel terminations are required when minimum clearance to
grade cannot be met (see Figure 16 on page 11).
• Have fireplace and selected vent components on hand to help
determine the exact measurements when elbowing or offsetting.
Always use wall firestops when penetrating walls and firestops
when penetrating ceilings or attic spaces.
• Install horizontal venting with a 1/4" rise for every 12" of run
toward the termination.
INSTALLATION PRECAUTIONS
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
• Installation of any damaged venting component
• Unauthorized modification of the venting system (Do not cut
or alter vent components)
• Installation of any component part not manufactured or approved by DESA
• Installation other than as instructed by these instructions
WARNING: This gas fireplace and vent assembly
must be vented directly to the outside. The venting
system must NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each
direct-vent gas appliance must use a separate vent
system. Do not use common vent systems.
WARNING: Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal
sections, which require 2" clearances from the top of
the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
do so could result in serious injury, property damage
or loss of life.
NOTICE: Failure to follow these instructions will void
the warranty.
NOTICE: Do not seal termination cap to vent pipe.
Cap must be removable for vent inspection and
maintenance.
For more information, visit www.desatech.com
111923-01B
8
VENTING INSTALLATION INSTRUCTIONS
Installation Planning
VENTING INSTALLATION
INSTRUCTIONS
Continued
Male
Slots
INSTALLATION PLANNING
There are two basic types of direct-vent installation:
• Horizontal Termination
• Vertical Termination
Female Locking Lugs
Horizontal Termination Installation
IMPORTANT: Horizontal square terminations require only inner
portion of wall firestop. Horizontal installations using round termination require exterior portion of wall firestop (see Figure 14, page 10).
1. Set the fireplace in its desired location and determine the route
your horizontal venting will take. Do not secure the fireplace
until all venting has been installed. Some installations require
sliding the fireplace in and out of position to make final venting
connections. Figures 14 through 18 on pages 10 through 12 show
different configurations for venting with horizontal termination
that will help you decide which application best suits your installation. Check to see if wall studs or roof rafters are in the
path of your desired venting route. If they are, you may want to
adjust the location of the fireplace.
2. Direct vent pipe sections and components are designed with
special twist-lock connections.
Twist-Lock Procedure: The female ends of the pipes have
locking lugs (indentations). These lugs will slide straight into
matching slots on the male ends of adjacent pipes. Push pipe
sections together and twist one section clockwise approximately one-quarter turn until the sections are fully locked
(see Figure 8). Note: Horizontal runs of vent must be supported every three feet. Use wall straps for this purpose.
3. Use a 45° elbow to connect venting system to fireplace flue collar. The elbow is designed to be twist-locked onto the flue collar
as described in step 2. IMPORTANT: Do not attempt to alter the
configuration of the elbow by cutting, twisting, bending, etc.
4. Assemble the desired combination of pipe and elbows to the
fireplace flue collar. If there are long portions of venting run,
pre-assembled pipe sections may be installed as subassemblies
for convenience.
5. Carefully determine the location where the vent pipe assembly
will penetrate the outside wall. The center of the hole should line
up with the center-line of the horizontal vent pipe. Mark the wall
for a 10 3/4" x 10 3/4" square hole. Cut and frame the square hole in
the exterior wall where the vent will be terminated. If the wall
being penetrated is constructed of noncombustible material, such
as masonry block or concrete, a 8 1/2" hole with zero clearance is
acceptable (see Figure 9).
Figure 8 - Vent Pipe Connections
Vent Opening
Combustible Wall
10 3/4"
(273mm)
10 3/4" Inside Framing
(273mm)
10 3/4"
(273mm)
Vent Opening
Noncombustible Wall
(Framing
Detail)
8 1/2"
(216mm)
Center
of Hole
Figure 9 - Vent Opening Requirements
For more information, visit www.desatech.com
111923-01B
VENTING INSTALLATION INSTRUCTIONS
9
9
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
WARNING: Do not recess vent termination into
any wall. This will cause a fire hazard.
6.
7.
8.
Cut Siding Away
to Fit Standoff
Noncombustible Exterior Wall: Position the horizontal vent
cap in the center of the 8 1/2" round hole and attach to the exterior wall with four wood screws provided. Before attaching
the vent cap to exterior wall, run a bead of non-hardening mastic
(pliable sealant) around the outside edges to make a seal between it and the outside wall. Note: The four wood screws
provided should be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of sidings.
Combustible Exterior Wall: For vinyl siding, stucco, or wood
exteriors, a siding standoff may be installed between the vent
cap and exterior wall. The siding standoff prevents excessive
heat from damaging the siding materials. Siding material must
be cut to accommodate standoff. Bolt the vent cap to the standoff. Apply non-hardening mastic around outside edge of standoff. Position the standoff/cap assembly in the center of the
10 3/4" square hole and attach to exterior wall with wood
screws provided (see Figure 11). The siding standoff must sit
flush against the exterior fascia material.
Combustible Exterior Wall Only: Slide the wall firestop over
the vent pipe before connecting horizontal run to vent cap (see
Figure 12).
Carefully move fireplace, with vent assembly attached, toward
wall and insert vent pipe into horizontal termination. The pipe
overlap should be a minimum of 11/4".
Vent Cap
Standoff
Wood Screw
Vent Cap
Screws
Apply Mastic
to All Four Sides
Figure 11 - Installing Siding Standoff (Combustible
Exterior Wall)
Interior Wall
Surface
Wall
Firestop
Vent Cap
(Horizontal
Termination)
Horizontal
Vent Pipe
Screw
Figure 12 - Connecting Vent Cap with Horizontal Vent Pipe
Wood Screw
Figure 10 - Installing Horizontal Vent Cap
(Noncombustible Exterior)
For more information, visit www.desatech.com
111923-01B
10
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
9.
Combustible Exterior Wall Only: Slide wall firestop against
interior wall surface and attach with screws provided. See Figure 13 for horizontal termination details.
10. Place fireplace into position and shim with noncombustible material if needed. Nail or screw side flanges to framing to secure
unit in place. IMPORTANT: Make sure fireplace is level before
securing. If fireplace is not level it will not work properly.
WARNING: Never run vent downward as this may
cause excessive temperatures which could cause a
fire. Operation of improperly installed and maintained venting system could result in serious injury,
property damage or loss of life.
GROUND FLOOR INSTALLATION
Minimum Pipe
Overlap 11/4"
Siding Standoff
Screws
Direct Vent
Pipe
Recommended Applications:
• Installation using cabinet surrounds
• Through the wall using round or square termination
(up to 12" horizontal pipe)
• NOT FOR CORNER INSTALLATION
45° Elbow
Horizontal High
Wind Square
Termination
Wall
Firestop
Adjustable
Pipe 12" Max.
Wall Firestop
Maintain 1"
Minimum Air
Space Around
Outer Pipe When
Penetrating a Wall
3
Square Termination
High Wind
Termination
3
10 /4" x 10 /4"
Framed
Opening
Vertical (V)
3
32 /4" min.
Apply Mastic to
Outside Edge of
Standoff
45° Elbow
Exterior Wall
with Vinyl Siding
Wall
Firestop
Horizontal (H)
17" max.
Exterior Portion of Wall
Firestop (Round
Termination Only)
Figure 13 - Typical Horizontal Termination Cap Mounting with
Additional Siding Standoff Installed
Horizontal Termination Configurations
Figures 14 through 18 show different configurations and alternatives
for venting with horizontal termination. Each figure includes a chart
with critical minimum and maximum dimensions which MUST be
met. IMPORTANT: Remember that a horizontal run of venting must
have a 1/4" rise for every 12" of run toward the termination.
NOTICE: Do not seal termination cap to vent pipe.
Cap must be removable for vent inspection and
maintenance.
Horizontal
Round
Termination
Round Termination
Figure 14 - Horizontal Termination Configuration for Square or
Round Terminations
For more information, visit www.desatech.com
111923-01B
VENTING INSTALLATION INSTRUCTIONS
11
11
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
CORNER INSTALLATION
Recommended Applications:
• Corner ground floor installation
• Ground floor installation where pipe vents horizontally through wall
(over 12" horizontal pipe)
• Basement installation where one foot clearance from ground to
termination is possible
Required
Vertical Pipe Horizontal (H)
None
30" max.
1 ft.
48" max.
2 ft.
60" max.
3 ft.
84" max.
4 ft.
20' max.
* Ground Floor Corner Venting
Not to Exceed
(H) Limits
Not to Exceed
(H) Limits
90° Elbow
Square
Termination
Wall
Firestop
Vertical (V)
*43 1/2" min.
54 1/2" min.
66 1/2" min.
78 1/2" min.
90 1/2" min.
90° Elbow
Square
Termination
As Required for (V)
See Chart for Pipe
Section Required
Wall
Firestop
12" Minimum
45°
Elbow
45° Elbow
Figure 15 - Horizontal Termination Configuration for Corner Installation Using One 90° Elbow
SNORKEL TERMINATION INSTALLATION
Recommended Applications:
• Installations requiring a vertical rise on building exterior
• Any installation using snorkel termination to achieve one foot above ground
Snorkel terminations are available for installations requiring a vertical rise on the exterior of the building. If
installing snorkel termination below grade, you must provide proper drainage to prevent water from entering snorkel
termination (see Figure 16). Do not back fill around snorkel termination.
Snorkel
Termination
Snorkel
Termination
90° Elbow
12"
Minimum
45°
Elbow
12"
Minimum
Adequate
Drainage
Figure 16 - Snorkel Termination Configurations for Below Ground Installation
For more information, visit www.desatech.com
111923-01B
Wall
Firestop
Snorkel
Termination
12"
Minimum
12
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
HORIZONTAL SYSTEM INSTALLATION USING TWO 90°
ELBOWS
The following configurations show the minimum vertical rise
requirements for a horizontal system using two 90° elbows.
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45°Elbow
6' max.
12' max.
18' max.
20' max.
20' max.
Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
6' max.
12' max.
18' max.
20' max.
20' max.
45° Elbow
Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace
For more information, visit www.desatech.com
111923-01B
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination
13
13
VENTING INSTALLATION
INSTRUCTIONS
Continued
INSTALLATION FOR VERTICAL TERMINATION
Note: Vertical restrictor must be installed in all vertical installations.
1. Determine the route your vertical venting will take. If ceiling
joists, roof rafters, or other framing will obstruct the venting
system, consider an offset (see Figure 19) to avoid cutting load
bearing members. Note: Pay special attention to these installation instructions for required clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, etc. Do not pack air spaces with insulation.
Also note maximum vertical rise of the venting system and
any maximum horizontal offset limitations.
2. Set the fireplace in desired location. Drop a plumb line down
from the ceiling to the position of the fireplace exit flue. Mark
the center point where the vent will penetrate the ceiling. Drill
a small locating hole at this point.
Drop a plumb line from the inside of the roof to the locating
hole in the ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
Roof Flashing
Wall Strap
45° Elbow
Ceiling Firestop
Figure 19 - Offset with Wall Strap and 45° Elbows
2.
Assemble the desired lengths of pipe and elbows necessary to
reach from the fireplace flue up through the firestop. Be sure
all pipe and elbow connections are fully twist-locked (see Figure 8, page 8).
3. Cut a hole in the roof using the locating hole as a center point.
(Cover any exposed open vent pipes before cutting hole in roof.)
The 10 3/4"x10 3/4" hole must be measured on the horizontal;
actual length may be larger depending on the pitch of the roof.
There must be a 1" clearance from the vent pipe to combustible
materials. Frame the opening as shown in Figure 9, page 8.
4. Connect a section of pipe and extend up through the hole.
Note: If an offset is needed to avoid obstructions, you must
support the vent pipe every 3 feet. Use wall straps for this
purpose (see Figure 19). Whenever possible, use 45° elbows
instead of 90° elbows. The 45° elbow offers less restriction to
the flow of the flue gases and intake air.
5. Place the flashing over the pipe section(s) extending through
the roof. Secure the base of the flashing to the roof and framing with roofing nails. Be sure roofing material overlaps the
top edge of the flashing as shown in Figure 19. There must be
a 1" clearance from the vent pipe to combustible materials.
6. Continue to add pipe sections until the height of the vent cap
meets the minimum building code requirements described in
Figure 7 on page 6. Note: You must increase vent height for
steep roof pitches. Nearby trees, adjoining rooflines, steep
pitched roofs, and other similar factors may cause poor draft
or down-drafting in high winds. Increasing the vent height may
solve this problem.
7. Twist-lock the vent cap onto the last section of vent pipe.
Note: If the vent pipe passes through any occupied areas above the first
floor, including storage spaces and closets, you must enclose pipe. You
may frame and sheetrock the enclosure with standard construction
material. Make sure and meet the minimum allowable clearances to
combustibles. Do not fill any of the required air spaces with insulation.
If area above is a room, install
firestop above framed hole.
Flat Ceiling Installation
1.
Cut a 10 3/4" square hole in the ceiling using the locating hole as
a center point. The opening should be framed to 10 3/4"x10 3/4"
(273mm x 273mm) inside dimensions, as shown in Figure 9 on
page 8 using framing lumber the same size as the ceiling joists.
If the area above the ceiling is an insulated ceiling or a room,
nail firestop from the top side. This prevents loose insulation
from falling into the required clearance space. Otherwise, install firestop below the framed hole. The firestop should be installed with no less than three nails per side (see Figure 20).
Figure 20 - Installing Firestop
For more information, visit www.desatech.com
111923-01B
If area above is not a room, install
firestop below framed hole.
14
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
Vertical Termination Configurations
Venting with One 90° Elbow
Figures 21 through 24 show four different configurations for vertical termination.
Venting with Two 90° Elbows
Vertical (V)
5' min.
6' min.
7' min.
8' min.
20' max.
45° Elbow
Horizontal (H1) +
Horizontal (H2)
Vertical (V)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
Note: Install
restrictor into inner
collar of fireplace
as shown.
45° Elbow
2' max.
4' max.
6' max.
8' max.
8' max.
Note: Install
restrictor into inner
collar of fireplace
as shown.
Figure 22 - Vertical Venting Configuration Using One 90° Elbow
(Vertical Round High Wind Termination Shown)
Venting with Two 90° Elbows
Figure 21 - Vertical Venting Configuration Using Two 90° Elbows
with Two Horizontal Runs (Vertical Round High Wind Termination
Shown)
Vertical (V1)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
6' max.
12' max.
18' max.
20' max.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Note: Vertical (V1) + Vertical (V2) = 40' max.
Figure 23 - Vertical Venting Configuration Using Two 90° Elbows
(Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
111923-01B
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
High Altitude Installation
15
15
VENTING INSTALLATION
INSTRUCTIONS
Continued
HIGH ALTITUDE INSTALLATION
Vertical Venting
V = 40' max.
Your DESA direct-vent fireplace has been tested and approved for
elevations from 0-2000 feet (USA) and elevations from 0-4500 feet
(Canada) .
When installing this fireplace at an elevation above 2000 feet (in the
USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet above sea level. Check with your local gas company for
proper orifice size identification.
When installing this fireplace at an elevation above 4500 feet (in
Canada), check with local authorities.
Consult your local gas company to help determine the proper orifice
for your location.
For assistance with any high altitude installation contact DESA’s
Customer Service Department at 1-866-672-6040.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Figure 24 - Vertical Venting Configuration With No Horizontal
Run (Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
111923-01B
16
VENTING INSTALLATION INSTRUCTIONS
Parts Lists for Venting Kits and Components
FIREPLACE INSTALLATION
Check Gas Type
Installing Optional Blower Accessories
VENTING INSTALLATION
INSTRUCTIONS
Continued
PARTS LISTS FOR VENTING KITS AND
COMPONENTS
DESA (5/8") Pipe & Vent Kits
Number Description
P58-6
P58-12
P58-24
P58-36
P58-48
PA58-712
6" Section Double Wall Pipe, Galvanized
12" Section Double Wall Pipe, Galvanized
24" Section Double Wall Pipe, Galvanized
36" Section Double Wall Pipe, Galvanized
48" Section Double Wall Pipe, Galvanized
Adjustable 7"-12" Section Double Wall Pipe, Galvanized
FPA58-6 6" Duravent Collar to FMI Pipe Adaptor (6" Collar/Pipe
Section)
DPA58-6 6" FMI Collar to Pipe Duravent Adaptor (6" Collar/Pipe
Section)
E58-45
45° Elbow, Galvanized
E58-90
90° Elbow, Galvanized
FSE58-45 45° Starter Elbow, Galvanized (Duravent Collar to
FMI Pipe)
DSE58-45 45 deg. Starter Elbow, Galvanized (FMI Collar to
Duravent Pipe)
VKG-58 Ground Floor Vent Kit
VKB-58 Basement Vent Kit
VKS-58 Snorkel Vent Kit
VKR-58 Roof Vent Kit
VKC-58 Corner Vent Kit
HTK
Horizontal Round Termination Kit
HT-58
Horizontal Round Termination, Galvanized
HTS-58 Horizontal Square Termination, Galvanized
VT-58
Vertical Round Termination, Galvanized
ST-58-14 14" Snorkel Termination, Galvanized
ST-58-36 36" Snorkel Termination, Galvanized
SC-58
Storm Collar, Galvanized
WF-58
Wall Firestop, Galvanized
RF-58-6 Roof Flashing - 0 to 6/12 Pitch, Galvanized
RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch, Galvanized
VR-58
Vertical Restrictor, Galvanized
S-58
Vinyl Siding Standoff, Galvanized
WS-58
Wall Strap
CS-58
Cathedral Ceiling Support
FP-58
Firestop Plate
SF-58
Stucco Flashing - For use with HTS-5
FIREPLACE INSTALLATION
.
CHECK
GAS TYPE
Use proper gas type for the fireplace unit you are installing. If you have
conflicting gas types, do not install fireplace. See retailer where you
purchased the fireplace for proper fireplace according to your gas type
or to purchase gas conversion kit (see Accessories, page 36).
INSTALLING OPTIONAL BLOWER
ACCESSORIES
NOTICE: If installing blower in an existing fireplace
with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex electrical outlet
installed in the right side of the bottom of the fireplace
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
Model BK Installation
Follow all instructions provided in the blower accessory kit.
1. Attach the power cord to the blower motor by firmly pushing the
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25).
2. Attach green ground wire from power cord to blower housing
using screw provided (see Figure 25). Tighten screws securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward. The blower
will fit inside the back opening and be held in position against
the back wall by the magnets (see Figure 25).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green
ground wire is tight.
Blower
Location
Lower Firebox
Cavity
Side View
Magnetic
Strips
Spade Terminals
Green Ground Wire
Screw
Exhaust Port
Figure 25 - Blower Model BK
For more information, visit www.desatech.com
111923-01B
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
17
17
FIREPLACE INSTALLATION
Continued
5.
6.
7.
8.
Mount speed control box to switch bracket by placing the plastic
control shaft forward through the round opening in the switch
bracket (see Figure 26).
While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it
is tight against front panel. Place control knob provided on shaft.
Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
Plug in blower power cord.
a. If your firebox is installed as a freestanding unit with an
accessory mantel, determine whether the power cord will
exit the left side or the right side of the firebox. Route power
cord through exit hole and plug the power cord into a wall
receptacle near the firebox.
b. If your firebox installation is recessed and/or pre-wired, plug
the power cord into the duplex outlet provided. Refer to your firebox owner’s manual for instructions on wiring the duplex outlet.
CAUTION: Never touch the blower wheel while in
operation.
9.
Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Turn blower on and check for operation. Turn blower off
by turning knob fully counterclockwise before continuing.
10. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27).
Note: When installing the BKT thermostatically-controlled blower,
you must first secure the thermal switch bracket to the blower if it
has not already been factory installed.
1. Place the green ground wire with ring terminal between the
bottom hole on the thermal switch bracket and the top ear hole
on the blower assembly. Insert the phillips screw into all three
pieces and tighten securely (see Figure 28).
2. Connect wire harness and power cord terminals. Connect the
blue jumper wire to the blower motor terminal and the right
side terminal of the thermal switch. Connect the black wire to
the left side of the thermal switch and the white wire to the
other remaining blower motor terminal.
Note: The power cord outer insulation sleeve may have to be
stripped slightly to allow enough wire length to reach and make all
connections. DO NOT trim excessive length away. Just enable
enough to make all connections securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward and the thermodisc
positioned up near the fireplace bottom. The thermodisc must be
oriented near the fireplace bottom as shown in Figure 28 in order
to sense temperature and properly operate. The blower will be
held in position against the back wall by the magnets incorporated onto the blower housing (see Figure 28).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and thermal switch, and that the screw
for the thermodisc bracket and green ground wire is tight.
Speed Control
Switch
Bracket
Control
Knob
Model BKT Installation
Blower
Plug-In
Locknut
Control Shaft
White Wire
Blue Wire
Power Cord
Thermal
Switch
Bracket
Duplex Outlet
(Located
underneath firebox
floor against lower
right outside wall)
Magnetic
Strips
Air Flow
Direction
Black
Wire
Phillips
Screw
Figure 26 - Attaching Speed Control to Firebox
Ring Terminal
on Green Wire
Air Flow Direction
Magnets
Thermal Switch
hc elba
tiw ira
Sn V
aF
B
ol
w M
r e ot o
r
nO
ff O
k
ca
kc lB
al
B
k
eti calB
hW
k
e c al
ne tihW B
er G
5
. C. 1 1/ 0
A.V 11
Wiring Diagram Decal
12" in Front of Blower
Route BKT
Blower Through
This Area
Thermodisc
Side View Firebox Bottom
Figure 28 - Blower Model BKT
Figure 27 - Location of Wiring Diagram Decal (Model May Vary
From Illustration)
For more information, visit www.desatech.com
111923-01B
Blower
Location
18
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
Installing Gas Piping to Fireplace Location
FIREPLACE INSTALLATION
Continued
Mount the speed control box against the mounting plate provided in the lower fireplace cavity by placing the plastic control
shaft forward through the round hole (see Figure 26, page 17).
6. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it is tight against mounting plate. Place control knob provided on shaft (see Figure 26, page 17).
7. Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Also double check all wire leads and make sure wire routing is not pinched or in a precarious position. Correct accordingly.
8. Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
9. Plug in blower power cord to duplex outlet.
10. The blower will only run when the speed control knob is in the
ON position and the thermal switch senses temperature after the
fireplace begins to heat up. The blower speed can be adjusted by
rotating the control knob. To turn off, turn knob fully counterclockwise until it clicks off. If the blower is ON and has been
running with the fireplace operating, the blower will continue to
run for a short time after the fireplace has been turned off. As the
thermal switch cools down, the blower shuts down automatically.
11. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27, page 17).
INSTALLING GAS PIPING TO FIREPLACE
LOCATION
Blower Wiring Diagram
* A CSA design-certified equipment shutoff valve with 1/8" NPT tap
is an acceptable alternative to test gauge connection. Purchase the
CSA design-certified equipment shutoff valve from your retailer.
5.
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
Variable
Fan Switch
Off
Fan Switch
(N.O.)
1
2
WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.
CAUTION: For propane/LP units, never connect
fireplace directly to the propane/LP supply. This
heater requires an external regulator (not supplied).
Install the external regulator between the fireplace
and propane/LP supply.
Installation Items Needed
Before installing fireplace, make sure you have the items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local codes)
For propane/LP connection only, the installer must supply an
external regulator. The external regulator will reduce incoming gas
pressure. You must reduce incoming gas pressure to between 11 and
14 inches of water. If you do not reduce incoming gas pressure,
fireplace regulator damage could occur. Install external regulator
with the vent pointing down as shown in Figure 30. Pointing the vent
down protects it from freezing rain or sleet.
Black
External
Regulator
On
Propane/LP
Supply Tank
Blue
110/115
V.A.C.
Black
White
Green
Blower
Motor
Figure 29 - Blower Wiring Diagram for Thermostat-Controlled
Models
Vent
Pointing
Down
Figure 30 - External Regulator with Vent Pointing Down
(Propane/LP Only)
For more information, visit www.desatech.com
111923-01B
FIREPLACE INSTALLATION
Installing Gas Piping to Fireplace Location (Cont.)
Connecting Fireplace to Gas Supply
Checking Gas Connections
19
19
FIREPLACE INSTALLATION
Continued
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to fireplace.
If pipe is too small, undue loss of volume will occur.
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from fireplace (see Figure 31).
IMPORTANT: Install main gas valve (equipment shutoff valve) in
an accessible location. The main gas valve is for turning on or
shutting off the gas to the appliance.
Check your building codes for any special requirements for locating
equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 31. Locate sediment trap/drip leg where it
is within reach for cleaning. Install in piping system between fuel
supply and fireplace. Locate sediment trap/drip leg where trapped
matter is not likely to freeze. A sediment trap traps moisture and
contaminants. This keeps them from going into fireplace gas controls. If sediment trap/drip leg is not installed or is installed wrong,
fireplace may not run properly.
CSA Design-Certified
Equipment Shutoff Valve
with 1/8" NPT Tap*
Approved Flexible
Gas Line
3" Minimum
CONNECTING FIREPLACE TO GAS SUPPLY
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower louver door panel by gently pulling forward.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to fireplace. Route flexible gas supply line through
one of the access holes on side of fireplace.
3. Attach flexible gas line from gas supply to control valve (see
Figure 32).
4. Check all gas connections for leaks. See Checking Gas
Connections.
To Gas Supply
(Natural)
To External
Regulator
(Propane/LP)
Equipment
Shutoff Valve
Control Valve
Flexible Gas Line
Do NOT Kink
Figure 32 - Connecting Flexible Gas Line to Millivolt Valve
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections ,
internal and external to unit, for leaks after installing
or servicing. Correct all leaks at once.
Natural - From
Gas Meter (5.5"
W.C. to 10.5"
W.C. Pressure)
Propane/LP
From External
Regulator (11"
W.C. to 14"
W.C. Pressure)
WARNING: Never use an open flame to check for a
leak. Apply noncorrosive leak detection fluid to all joints.
Bubbles forming show a leak. Correct all leaks at once.
Pressure Testing Gas Supply Piping System
Cap
Figure 31 - Gas Connection
Pipe Nipple
Tee Joint
Sediment Trap/Drip Leg
* The CSA design-certified equipment shutoff valve may be supplied with the appliance or you can purchase it from your retailer.
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
Disconnect fireplace and its individual equipment shutoff valve
from gas supply piping system. Pressures in excess of 1/2 psig
(3.5 kPa) will damage fireplace gas regulator.
For more information, visit www.desatech.com
111923-01B
20
FIREPLACE INSTALLATION
Checking Gas Connections (Cont.)
Installing Optional Wall Mount Switch - GWMS2
FIREPLACE INSTALLATION
Continued
2.
3.
4.
5.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace, or using compressed air.
Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a
leak. Correct all leaks at once.
Reconnect fireplace and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.
Equipment
Shutoff
Valve
Gas
Meter
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
Close equipment shutoff valve (see Figure 33).
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace, or using compressed air.
Check all joints from propane/LP supply tank or gas meter to
equipment shutoff valve (see Figure 34, for propane/LP or
Figure 35, for natural gas). Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct
all leaks at once.
Equipment
Shutoff
Valve
Gas Valve
Figure 35 - Checking Gas Joints for Natural Gas Fireplace
Pressure Testing Fireplace Gas Connections
1.
2.
3.
4.
Open
5.
Closed
Figure 33 - Equipment Shutoff Valve
6.
INSTALLING OPTIONAL WALL MOUNT
SWITCH - GWMS2
1.
Propane/LP
Supply Tank
Open equipment shutoff valve (see Figure 33).
Open propane/LP supply tank valve for propane/LP fireplace
or main gas valve located on or near gas meter for natural
gas fireplace.
Make sure control knob of fireplace is in the OFF position.
Check all joints from equipment shutoff valve to gas valve
(see Figure 34 for propane/LP or Figure 35 for natural gas).
Apply noncorrosive leak detection fluid to all joints. Bubbles
forming show a leak. Correct all leaks at once.
Light fireplace (see Operating Fireplace, pages 23 through
26). Check all other internal joints for leaks.
Turn off fireplace (see To Turn Off Gas to Appliance, page 24).
Equipment
Shutoff
Valve
2.
3.
4.
Connect one terminal of 25 ft. wire for the wall switch to the
TPTH terminal on the valve. Connect remaining wire terminal
to the TH terminal on the valve. Make sure that the wire terminals are in the positions on the unit as pictured in Figure 36. If
wires are not connected as shown the switch will not work.
Route the 25 ft. wire through openings provided on the sides of
the burner system to a convenient location to mount your switch.
Connect one bare wire end to each of the terminals of the
GWMS2 wall switch.
Install the wall switch and cover in the wall.
To Wall Switch
Accessory
Gas Valve
Figure 34 - Checking Gas Joints for Propane/LP Gas Fireplace
Figure 36 - Connecting Wall Swith to Control Valve
For more information, visit www.desatech.com
111923-01B
FIREPLACE INSTALLATION
Installing Optional Wireless Hand-Held Remote Control - GHRCB and GHRCTB Series
Removing/Replacing Glass Door
21
21
FIREPLACE INSTALLATION
Continued
INSTALLING OPTIONAL WIRELESS HANDHELD REMOTE CONTROL - GHRCB AND
GHRCTB SERIES
NOTICE: Use only alkaline batteries (not included).
3.
4.
5.
6.
Terminal
Wires
9-Volt
Alkaline
Battery
Battery
Housing
Figure 39 - Installing Alkaline Battery in Hand-Held Remote
Control Unit (GHRCB)
Installing Remote Receiver
1.
2.
Remote Control Unit
Battery Cover
Open bottom louver and locate the switch bracket on the left.
Unscrew the switch bracket. Lean bracket forward so you are
able to access the back of the remote receiver.
Locate the battery clip mounted on the back of the receiver.
Slide a 9-volt alkaline battery (not included) through the clip
(see Figure 37).
Attach the terminal wires to the battery.
Connect wires from receiver to TH and TPTH to control valve
(see Figure 38).
Replace the switch bracket.
9-Volt
Battery
Terminal
Wires
Remote
Control
Unit
Battery
Cover
Figure 40 - Installing Battery in Hand-Held Remote Control Unit
(GHRCTB Series)
REMOVING/REPLACING GLASS DOOR
Receiver
CAUTION: Do not operate this fireplace with a
broken glass door panel or without the glass door
panel securely in place. For replacement part information see Replacement Parts, page 31.
9-Volt Alkaline
Battery
Terminal Wires
Battery Clip
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
Figure 37 - Attaching Alkaline Battery to Receiver
To Optional
Remote
Accessory
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before removing
glass door or louvers.
Removing Louver Panels
Figure 38 - Control Valve Terminals
Installing 9-Volt Alkaline Battery in Hand-Held
Remote Control Unit
1.
2.
3.
Remove battery cover on back of remote control unit.
Attach terminal wires to a 9-volt alkaline battery (not included).
Place battery into the battery housing.
Replace battery cover onto remote control unit.
Remove the top and bottom louver panels by simultaneously pulling
both top end spring latches towards the center of the appliance until
they are disengaged from the locating holes (see Figure 41). Repeat
for bottom spring latches and pull the louvers outward. To install or
replace items removed, simply reverse the procedures above.
Louver Panel
Spring Latch
Figure 41 - Removing Louver Panel
For more information, visit www.desatech.com
111923-01B
FIREPLACE INSTALLATION
22
Removing/Replacing Glass Door (Cont.)
Installing Optional Brick Liner Models BL36D(S) and BL36DH(S)
FIREPLACE INSTALLATION
Continued
Removing Glass Doors
If replacement of glass is necessary, the entire assembly, glass and
frame, must be replaced. If glass is broken, wear gloves and tape the
remaining fragments onto the frame.
1. Remove screen assembly by pushing the rod either left or right
and then down and forward to remove screen/rod assembly
from the firebox. Set assembly aside.
2. Lift up on latches to unlock. There are two on top of firebox and
two below firebox that hold glass door in place (see Figure 42).
3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on
the left side of door frame assembly (see Figure 42).
4. Remount the new frame at the hinge with five new screws
before closing door. This will ensure seating of the gasket.
5. Close glass door frame. Lock latches by placing the bar under the
tab on door and pushing down and back on latch (see Figure 42).
6. Replace screen/rod assembly by reversing step 1.
7. Replace louvers by reversing procedure under Removing
Louver Panels, page 21.
Cleaning Glass Door
See Cleaning and Maintenance on page 27.
Latch Unlock
Lock
Screw
INSTALLING BRICK LINER MODELS
BL36DA(SA) AND BL36DHA(SA)
WARNING: If fireplace has been running, turn
off unit. Let cool before installing brick liner.
You may purchase brick liner from your local retailer or see
Accessories, page 36.
CAUTION: Always handle brick panels with two
hands. Do not force brick panels into place. Excessive force will break brick panels.
1.
2.
Remove top and bottom louvers to allow access to door latches.
Unlock door latches and open glass door. See Removing/Replacing Glass Door, steps 1 and 2.
3. If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs,
lava rock, and ember material.
4. Remove three screws from deflector shield on the inside top
of firebox. Set shield and screws aside.
5. Install rear brick panel first. Rest bottom edge of panel on back
edge of burner assembly (see Figure 43).
6. Install left side brick panel by sliding it between the burner
assembly and the side of the firebox (see Figure 43).
7. Install the right brick panel using the same method described
8. Replace deflector shield using screws removed in step 4.
9. Follow instructions to install logs, lava rock, and ember material.
10. Close glass door and lock latches on top and bottom of door
and replace screen. See Removing/Replacing Glass Door,
steps 5 and 6.
11. Close top and bottom louvers.
Hinge
Left Side
Brick Panel
Glass Frame
Assembly
Figure 42 - Removing/Replacing Glass Door
Rear Brick
Panel
Figure 43 - Installing Rear Brick Panel
For more information, visit www.desatech.com
111923-01B
FIREPLACE INSTALLATION
Installing Logs, Lava Rock and Glowing Embers
23
23
OPERATING FIREPLACE
For Your Safety Read Before Lighting
FIREPLACE INSTALLATION
Continued
INSTALLING LOGS, LAVA ROCK AND
GLOWING EMBERS
5
Each log is marked with a number. These numbers will help you
identify the log when installing. It is very important to install these
logs exactly as instructed. Do not modify logs. Only use logs
supplied with fireplace.
Open louvers, remove screen, unlock door latches, and open glass
door. See Removing/Replacing Glass Door, steps 1 and 2 on page 22.
Install logs according to instructions for fireplace model numbers.
1. Place log #1 (left base log) onto pin on left side of burner as
shown in Figure 44.
2. Place log #2 (right base log) onto pin on right side of burner as
shown in Figure 44.
3. Place logs #3 (left front log) and log #4 (right front log) onto
pins as shown in Figure 45.
4. Place log #5 (right rear log) onto pins on right rear of burner
(see Figure 46). Rest log #6 (middle crossover log) on top of
log number 2 as shown in Figure 46.
5. Place back end of log #7 (left rear log) onto pin on left rear
burner and rest front onto log #1 as shown in Figure 47.
6. Rest log #8 (left crossover log) onto log #3 and rest log #9 (right
crossover log) onto logs #4 and #5 as shown in Figure 48.
7. Pull ember material apart into pieces no larger than a dime. Place
these pieces loosely and sparingly directly onto the exposed front
section of the burner (see Figure 49). This will create the glowing
ember appearance as the flame touches the ember material. Do
not block air slots by using too much ember material in one area.
It is not necessary to use all of the ember material provided.
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner will cause performance problems.
8.
Close glass door, lock door latches, replace screen, and close
louvers (see Removing/Replacing Glass Door, steps 5 through
7 on page 22).
WARNING: The glass door must be securely in
place before running this fireplace. Do not run this
fireplace if glass is missing or broken.
2
1
Figure 44 - Installing Logs
No. 1 and No. 2
3
4
6
Figure 46 - Installing Logs
No. 5 and No. 6
Figure 47 - Installing Log No. 7
9
8
Figure 48 - Installing Logs No. 8 and No. 9
Ember Material
Figure 49 - Placing Ember Material on Burner
OPERATING FIREPLACE
FOR YOUR SAFETY READ
BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
Figure 45 - Installing Logs
No. 3 and No. 4
For more information, visit www.desatech.com
111923-01B
7
24
OPERATING FIREPLACE
For Your Safety Read Before Lighting (Cont.)
Lighting Instructions
To Turn Off Gas To Appliance
Manual Lighting Procedure
Optional Hand-Held Remote Operation
OPERATING FIREPLACE
Continued
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to inspect the appliance and to replace any part
of the control system and any gas control which has
been under water.
LIGHTING
INSTRUCTIONS
1.
2.
3.
4.
STOP! Read the safety information above.
Open lower louver panel.
Turn off all electric power to the fireplace.
Push in gas control knob slightly and turn clockwise
to “OFF”.
5. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don't smell
gas, go to the next step.
6. The pilot is located by the main burner and should not require accessing for lighting.
7. Turn gas control knob counterclockwise
to “PILOT”.
8. Push in gas control knob all the way and hold. Immediately light the pilot by repeatedly depressing the piezo spark
ignitor until a flame appears. Continue to hold for about
one (1) minute after the pilot is lit. Release gas control knob
and it will pop back. Pilot should remain lit. If it goes out,
repeat steps 5 through 8.
• If gas control knob does not pop up when released, stop
and immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician
or gas supplier.
9. Turn on all electric power to the fireplace.
10. Turn gas control knob counterclockwise
to “ON”.
11. This valve is equipped with a HI/LO feature. Set fireplace
input as desired.
12. Close lower louver panel.
3.
4.
5.
ON
OFF
IH
LO
Open lower louver panel.
Set selector switch in the OFF position to prevent draining
battery.
Turn off all electrical power to the appliance if service is to
be performed.
Push in gas control knob slightly and turn clockwise
to “OFF”.
Close lower louver panel.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
1. Turn gas control knob clockwise
to the PILOT
position.
2. Set selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
1.
2.
3.
4.
5.
Remove glass door (see Removing/Replacing Glass Door,
pages 21 and 22).
Follow steps 1 through 8 under Lighting Instructions.
Depress gas control knob and light pilot with match.
Keep gas control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release gas control knob. Follow steps 10 through 14 under Lighting Instructions.
Replace glass door (see Removing/Replacing Glass Door,
pages 21 and 22).
OPTIONAL HAND-HELD
REMOTE OPERATION
Note: All remote control accessories must be purchased separately (see Accessories, page 36). Follow instructions included
with the remote control.
NOTICE: You must light the pilot before using the handheld remote control unit. See Lighting Instructions.
1.
LOT
PI
Figure 50 - Control Valve
1.
2.
Variable Control Knob
Gas Control
Knob
Piezo
Ignitor
TO TURN OFF GAS
TO APPLIANCE
After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position (see Figure 51, page
25). Note: The burner may light if hand-held remote was
on when selector switch was last turned off. You can now
turn the burner on and off with the hand-held remote control unit.
For more information, visit www.desatech.com
111923-01B
OPERATING FIREPLACE
Optional Hand-Held Remote Operation (Cont.)
25
25
OPERATING FIREPLACE
Continued
IMPORTANT: Do not leave the selector switch in the REMOTE or ON position when the pilot is not lit. This will
drain the battery.
4.
Blower Control Knob
(Optional Accessory)
Variable
Control Knob
T
F
ON
OFF
REMOTE
OF
LO
PILO
Selector Switch
in Remote
Position
HI
ON
ON
OFF
Gas Control Knob
in ON Position
Figure 51 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
ON/OFF SERIES MODEL GHRCB
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 52).
TO LOCK press both buttons on hand-held remote control until
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
TO UNLOCK press both buttons together on hand-held remote
control until the light stops flashing. The hand-held remote is
now unlocked.
Control Button
Turns Burners
On and Off
Figure 52 - On/Off Hand-Held Remote Control Unit GHRCB
THERMOSTAT SERIES MODEL GHRCTB
The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 53). To
select Fahrenheit/Centigrade mode display, carefully press the ˚C/
˚F mode button with the end of a paper clip or similar blunt object.
Manual Mode
1.
2.
3.
Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
Press the MANU button to turn on the fireplace.
Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
1.
2.
3.
Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
Press AUTO button to select this mode.
Set the desired room temperature by pressing the TEMP
+ or - buttons.
Press the POWER and LOCK buttons together to turn off
the fireplace
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Digital Display
Shows
Temperature and
Settings
Turns Hand-Held
Remote On or Off and
Allows You to Choose
the Manual Setting
Turns Burners
On or Off
Selects Auto Setting
Decreases Room
Temperature in
AUTO Mode
Locks System to
Prevent Accidental
Ignition
Figure 53 - Thermostat Hand-Held Remote Control Unit GHRCTB
Safety Features
When away from home for an extended period of time or as a
child safety feature to prevent accidental ignition of the fireplace, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
Auto Shutoff Feature
1. If the average room temperature exceeds 82 degrees Fahrenheit (28 degrees Centigrade), the hand-held remote control will perform a safety override and shut the fireplace
off. This feature is not available in the MANU mode.
2. The receiver continuously receives signals from the handheld remote to control the room temperature. If the handheld remote is misplaced, obstructed, or for any reason
cannot transmit to the receiver, the receiver will shut off
the fireplace after 8 minutes.
Key Pad Lock Feature
This feature allows the user to lock/unlock the keypad on the
hand-held remote in the MANU or AUTO mode to prevent
inadvertent operation (i.e. children operating the hand-held remote control, etc.). The keypad is locked in either on or off. Press
the POWER and LOCK buttons together to turn the unit on or off.
For more information, visit www.desatech.com
111923-01B
Increases Room
Temperature in AUTO
Mode
26
OPERATING FIREPLACE
Operating Optional GWMT1 Wall Mounted Thermostat
Operating Optional Blower Accessory
INSPECTING BURNERS
Pilot Assembly
Burner Flame Pattern
OPERATING FIREPLACE
Continued
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT ASSEMBLY
WARNING: Do not connect the thermostat to a
power source. Electrical shock and/or a fire hazard
will occur.
Light the fireplace as instructed in Lighting Instructions on
page 24. Set wall thermostat to desired temperature.
This thermostat has been electronically calibrated at the factory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper
operation.
To turn the fireplace off, adjust thermostat to the lowest setting
and turn the gas control knob back to PILOT. The pilot will
remain lit.
The pilot assembly is factory preset for the proper flame height.
Alterations may have occurred during shipping and handling. Call
a qualified service person to readjust the pilot if necessary.
The height of the thermopile must be 3/8" to 1/2" above the pilot
flame as shown in Figure 54. The thermocouple must be at a height
of about 1/8" above the pilot flame. The flame from the pilot burner
must extend beyond both the thermocouple and thermopile.
If you pilot assembly does not meet these requirements:
• turn fireplace off (see To Turn Off Gas to Appliance, page 24)
• see Troubleshooting, pages 28 through 30
Thermopile
3/8" to 1/2"
Pilot Burner
IMPORTANT: To turn the pilot off, turn the gas control knob
on the heater to the OFF position.
1/8"
OPERATING OPTIONAL
BLOWER ACCESSORY
Locate the blower controls by opening the lower louver panel on
the fireplace. Blower controls are located on the left side of the
switch bracket to the left just inside the louver panel.
The BK manual blower and the BKT thermostatically-controlled blower have an ON setting and an OFF setting. The
blower will only run when the switch is in the ON position. In the
OFF position, the blower will not operate.
Note for BKT Only: If you are using BKT blower with optional
thermostat (wall mounted or remote control) for the fireplace,
your fireplace and blower will not turn on and off at the same
time. The fireplace may run for several minutes before the
blower turns on. After the heater modulates to the pilot position,
the blower will continue to run. The blower will shut off after the
firebox temperature decreases.
The blower helps distribute heated air from the fireplace.
Periodically check the louvers of the firebox and remove any
dust, dirt, or other obstructions that will hinder the flow of air.
Thermocouple
Piezo
Ignitor
Figure 54 - Pilot Assembly
BURNER FLAME PATTERN
Burner flames will be steady; not lifting or floating. Flame patterns
will be different from unit to unit and will vary depending on
installation type and weather conditions.
If the vent configuration is installed incorrectly, the flames will lift
or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.
Figure 55 shows a typical flame pattern.
If burner flame pattern differs from that described:
• turn fireplace off (see To Turn Off Gas to Appliance, page 24)
• see Troubleshooting, pages 28 through 30
Figure 55 - Typical Flame Pattern
For more information, visit www.desatech.com
111923-01B
CLEANING AND MAINTENANCE
Glass Door
Pilot and Burners
Logs
Venting System
27
27
CLEANING AND MAINTENANCE
WARNING: Turn off fireplace and let cool before
cleaning.
CAUTION: You must keep control areas, burners,
and circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have
fireplace inspected yearly by a qualified service person.
Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.
GLASS DOOR
WARNING: Handle glass door panel with care. Do not
strike, slam, or otherwise abuse glass. Do not operate
fireplace with the glass door removed, cracked, or broken.
Use only the tempered glass door replacement intended for this
fireplace (see Replacement Parts, page 31 for detail on ordering).
No substitutions may be made. See Removing/Replacing Glass
Door, pages 21 and 22 for instructions for replacing glass door.
WARNING: Do not operate fireplace with the glass
door removed, cracked, or broken.
PILOT AND BURNERS
• Remove ember material before cleaning burners and replace
when cleaning is complete.
• Burner and controls should be cleaned with compressed air to
remove dust, dirt, or lint.
• Use a vacuum cleaner or small, soft bristled brush to remove
excess dust, dirt, or lint.
LOGS
WARNING: Do not use abrasive cleaners as this
may damage glass. Use a nonabrasive household glass
cleaner to clean glass. Do not clean glass when hot.
Glass must be cleaned periodically. During start-up it is normal for
condensation to form on the inside of the glass causing lint, dust, and
other airborne particles to cling to the glass surface. During initial
start-up a slight film may form on the glass due to paint curing. The
glass should be cleaned several times with a non-ammonia, nonabrasive household cleaner and warm water after the first two weeks
of operation. Thereafter, clean the glass two or three times during
each heating season, depending on the usage and circumstances
present. Refer to Removing/Replacing Glass Door, pages 21 and 22
of this manual when removing glass door for cleaning.
WARNING: Only parts supplied by the manufacturer should be used when replacing broken or damaged glass door panel (see Replacement Parts, page
31). This glass door panel is a complete unit. No
substitute materials may be used.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
• If you remove logs for cleaning, refer to Installing Logs, Lava
Rock, and Glowing Embers, page 24, to properly replace logs.
• Use a vacuum cleaner to remove any carbon buildup on logs.
• Replace log(s) if broken. See Replacement Parts on page 31.
• Replace ember material periodically as needed. See Replacement Parts on page 31.
VENTING SYSTEM
Conduct annual inspection of the venting system following these
guidelines:
1. Check areas of venting system that are exposed to the weather for
corrosion (rust spots or streaks and, in extreme cases, holes). Have
these items replaced immediately by a qualified service person.
2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.
3. Check for evidence of excessive condensation. Continuous
condensation can cause corrosion of caps, pipes, and fittings
and can be caused by having excessive lateral runs, too many
elbows, or exterior portions of the system being exposed to
cold weather.
4. Inspect joints to verify that no pipe section or fitting has been
disturbed and loosened. Check mechanical supports such as wall
straps for rigidity.
If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, pages 21 and 22). Vacuum all glass
pieces with a shop vac.
CAUTION: Do not vacuum if pieces are hot.
For more information, visit www.desatech.com
111923-01B
28
TROUBLESHOOTING
TROUBLESHOOTING
Note: For additional help, visit
DESA’s technical service web site at
www.desatech.com.
WARNING: Turn off heater and
let cool before servicing. Only a qualified service person should service
and repair heater.
Note: All troubleshooting items are listed in
order of operation.
CAUTION: Never use a wire,
needle, or similar object to
clean pilot. This can damage
pilot unit.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3. Piezo ignitor nut is loose
4.
5.
6.
7.
When ignitor button is pressed, there is
spark at pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Gas control knob not in PILOT position
3. Gas control knob not pressed in while
in PILOT position
4. Air in gas lines when installed
5. Depleted gas supply (propane/LP models
only)
6. Pilot is clogged
7. Gas regulator setting is not correct
Pilot lights but flame goes out when control
knob is released
1. Gas control knob not fully pressed in
2. Gas control knob not pressed in long
enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor. Nut
is located behind the mounting bracket
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace pilot assembly
7. Replace pilot assembly
1. Turn on gas supply or open equipment
shutoff valve
2. Turn gas control knob to PILOT position
3. Press in gas control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is removed
5. Contact local propane/LP gas company
6. Clean pilot (see Cleaning and Maintenance, page 27) or replace pilot assembly
7. Replace gas control
1. Press in gas control knob fully
2. After pilot lights, keep gas control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural or propane/LP
gas company
B) Clean pilot (see Cleaning and
Maintenance, page 27) or replace pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace pilot assembly
7. Replace control valve
For more information, visit www.desatech.com
111923-01B
TROUBLESHOOTING
29
29
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Maintenance, page 27) or replace burner orifice
2. Contact local propane/LP or natural gas
company
3. Reconnect leads
2. Inlet gas pressure is too low
3. Thermopile leads disconnected or improperly connected
4. Thermopile is defective
Delayed ignition burner
1. Manifold pressure is too low
2. Burner porting or orifice clogged
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
4. Replace thermopile
1. Contact local propane/LP or natural gas
company
2. Clean burner (see Cleaning and Maintenance, page 27) or replace burner orifice
2. Damaged burner
3. Gas regulator defective
1. Clean burner (see Cleaning and Maintenance, page 27) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
Slight smoke or odor during initial operation
1. Residues from manufacturing processes
and logs curing
1. Problem will stop after a few hours of
operation
Heater produces a whistling noise when
burner is lit
1. Turning gas control knob to HI position
when burner is cold
2. Air in gas line
1. Turn gas control knob to LO position and
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local propane/LP or natural gas company
3. Clean burner (see Cleaning and Maintenance, page 27) or replace burner orifice
3. Dirty or partially clogged burner orifice
2. Debris around burner air mixer
1. Adjust the log set so that the flame does
not excessively impinge on it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
Fireplace produces a clicking/ticking noise
just after burners are lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common. If noise is excessive,
contact qualified service person
Remote does not function
1. Battery is not installed or battery power
is low
1. Replace 9-volt batteries in receiver and
remote control
Glass soots
1. Flame impingement on logs
For more information, visit www.desatech.com
111923-01B
30
TROUBLESHOOTING
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
•
•
•
•
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Fireplace produces unwanted odors
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, pages 19 and 20)
Fireplace shuts off in use
1. High or gusting winds
1. Fireplace has been tested for up to
40mph winds. However, extreme conditions may occur. See Lighting Instructions on page 24
2. Contact local propane/LP or natural gas
company
3. Clean pilot (see Cleaning and Maintenance, page 27)
4. Locate and correct all leaks (see Checking Gas Connections, pages 19 and 20)
5. Tighten glass
2. Low line pressure
3. Pilot is partially clogged
4. Inner vent pipe leaking exhaust gasses
into system
5. Glass too loose and air tight gasket leaks
in corners after usage
6. Bad thermopile or thermocouple
7. Improper vent cap installation
6. Replace faulty component
7. Check for proper installation and freedom from debris or blockage
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement
above
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, pages 19 and 20)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, pages 19 and 20)
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing Logs,
Lava Rock, and Glowing Embers, page 23)
2. Clean out air holes at burner inlets. Periodically repeat as needed
3. Remove blockage or replace burner
4. Have the vent system inspected, including the termination cap. Remove any
restrictions or obstruction
5. Clear excess embers until a minimum
gap of 1/2" remains under the grate
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
4. Improper venting or excessive blockage
5. Excessive amounts of embers and pan
material
For more information, visit www.desatech.com
111923-01B
REPLACEMENT PARTS
SPECIFICATIONS
SERVICE HINTS
TECHNICAL SERVICE
REPLACEMENT PARTS
SERVICE HINTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
When Gas Pressure Is Too Low
PARTS UNDER WARRANTY
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESA’s Customer Service Department at 1-866-672-6040.
When calling DESA, have ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
•
•
•
•
pilot will not stay lit
burners will have delayed ignition
fireplace will not produce specified heat
propane/LP gas supply might be low (propane/LP units only)
You may feel your gas pressure is too low. If so, contact your local
gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. If so, contact DESA’s Customer Service Department at 1-866-672-6040. When calling, please have your model and
serial numbers of your heater ready.
You can also visit DESA’s technical service web site at
www.desatech.com.
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESA at 1-866-672-6040 for
referral information.
When calling DESA, have ready
• model number of your fireplace
• the replacement part number
SPECIFICATIONS
(V)K36N Series
(V)K36P Series
19,000/27,000 Btu/hr
18,000/26,000 Btu/hr
Natural
Propane/LP
Piezo
Piezo
Manifold Pressure
3.5" w.c.
10.0" w.c.
Minimum Inlet
Supply Pressure
5.5" w.c.
11.0" w.c.
Btu
Gas Type
Ignition
Dimension (H x W x D) Fireplace
(Actual size of firebox.
36" x 41" x 21 1/8"
Measurements do not include
914 x 1041 x 537 mm
nailing flanges or standoffs).
Carton
Weight, lbs/kg*
Fireplace
Shipping
36" x 41" x 21 1/8"
914 x 1041 x 537 mm
38" x 44" x 22"
965 x 1118 x 559 mm
38" x 44" x 22"
965 x 1118 x 559 mm
165 lbs/75 kg
168 lbs/76 kg
165 lbs/75 kg
168 lbs/76 kg
For more information, visit www.desatech.com
111923-01B
31
31
32
ILLUSTRATED PARTS BREAKDOWN
Models (V)K36N, (V)K36NH, (V)K36P, (V)K36PH
ILLUSTRATED PARTS
BREAKDOWN
MODELS
(V)K36N, (V)K36NH, (V)K36P, (V)K36PH
10-9
10-7
10-8
10-5
6
7
10-6
8
10-4
1
10-3
4
9
10-2
11
3
10-1
20
18
14
16
15
19
12
17
21
13
2
5
For more information, visit www.desatech.com
111923-01B
PARTS LIST
Models (V)K36N, (V)K36NH, (V)K36P, (V)K36PH
PARTS LIST
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 31 of this manual.
KEY
NO.
1
2
3
4
5
6
7
8
9
10
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
10-9
11
12
13
14
15
16
17
18
19
20
21
PART
NUMBER
**
**
108010-01
108010-02
108011-01
108011-02
**
**
**
109082-01
111958-01
111933-01
111932-01
111961-01
111960-01
111926-01
111929-01
111959-01
111930-01
111962-01
See Below
See Below
See Below
108719-01
12105
11418
14123
21171
24353
24460
111956-01
111956-02
DESCRIPTION
QTY.
Firebox Assembly
1
Face Weldment
1
Door Assembly
1
Door Assembly (V Models Only)
1
Top Louver Assembly
1
Bottom Louver Assembly
1
Fireplace Top
1
Fireplace Top Insulation
1
Fireplace Surround
1
Heat Shield
1
Log Set
1
Left Base Log
1
Right Base Log
1
Left Front Log
1
Right Front Log
1
Right Rear Log
1
Middle Crossover Log
1
Left Rear Log
1
Left Crossover Log
1
Right Crossover Log
1
Left Refractory Brick Panel
1
Rear Refractory Brick Panel
1
Right Refractory Brick Panel
1
Screen Rod
1
Screen
2
Push-On Nut
2
Strain Relief
1
Gas Knock-Out Cover
2
Handy Box Assembly
1
Gas Conduit Assembly
1
Burner Assembly (Natural Gas)(See pages 34 and 35)
1
Burner Assembly (Propane/LP Gas)
1
PARTS AVAILABLE - NOT SHOWN
25487
27253
55240
Lava Rock/Bag Assy
Notice Label
Vent Label
1
1
1
** Part not available for field replacement.
REFRACTORY BRICK PANELS
K36N
K36P
VK36N
VK36P
K36NH
K36PH
VK36NH
VK36PH
110989-02
110991-02
110990-02
110989-01
110991-01
110990-01
111215-02
111217-02
111216-02
111215-01
111217-01
111216-01
DESCRIPTION
Left Refractory Brick Panel
Rear Refractory Brick Panel
Right Refractory Brick Panel
For more information, visit www.desatech.com
111923-01B
QTY
1
1
1
33
33
34
ILLUSTRATED PARTS BREAKDOWN
Models (V)K36N, (V)K36NH, (V)K36P, (V)K36PH
ILLUSTRATED PARTS
BREAKDOWN
BURNER ASSEMBLY FOR MODELS
(V)K36N, (V)K36NH, (V)K36P, (V)K36PH
1
12
7
12
16
2
10
15
3
13
12
(#56)
4
5
9
TPTH TP TH
5
11
12
6
14
17
8
For more information, visit www.desatech.com
111923-01B
PARTS LIST
Models (V)K36N, (V)K36NH, (V)K36P, (V)K36PH
PARTS LIST
BURNER ASSEMBLY FOR MODELS
(V)K36N, (V)K36NH, (V)K36P, (V)K36PH
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 31 of this manual.
KEY
NO.
PART
NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
111957-01
111311-01
111313-01
26808
11107
111310-01
11102
111912-01
111288-02
108084-02
108084-03
14389
14390
11165
111913-02
14500
111316-01
104506-23
104506-17
26827
Pan Assembly Burner
Grate Base
Burner Base Bottom
Valve Bracket
Screw, #10-32 x 1/4 PPH Zinc
Firebox Bottom
Screw, #8-32 x 3/8 PPH Zinc
Tubing Assembly
Flex Gas Line
Pilot Assembly (Natural Gas)
Pilot Assembly (Propane/LP Gas)
Hi-Lo Natural Gas Valve
Hi-Lo Propane/LP Gas Valve
Screw, #10 x 5/8 HWH Zinc
Burner Base Gasket
Brass Fitting
Pilot Bracket
Burner Orifice (Natural Gas)
Burner Orifice (Propane/LP Gas)
Switch Bracket
11
12
13
14
15
16
17
QTY.
1
1
1
1
4
1
2
1
1
1
1
1
1
22
1
1
1
1
1
1
For more information, visit www.desatech.com
111923-01B
35
35
36
ACCESSORIES
ACCESSORIES
NOTICE: All accessories may not be available for all
fireplace models.
Purchase these fireplace accessories from your local retailer. If they
can not supply these accessories, call DESA’s Sales Department at
1-866-672-6040. for information. You can also write to the address
listed on the back page of this manual.
MANUAL BLOWER KIT - BK
Manual variable control blower accessory provides better heat
distribution. Complete installation and operation instructions included in this manual.
BRICK LINER
(Not Shown)
BL36DA - Textured Refractory Brick Liner Kit
BL36DSA - Standard Refractory Brick Liner Kit
BL36DHA - Textured Refractory Herringbone Brick Liner Kit
BL36DHSA - Standard Refractory Herringbone Brick Liner Kit
This brick liner adds a touch of style to your direct-vent fireplace.
Complete installation instructions included in this manual.
FLEXIBLE GAS LINE CONNECTOR - GA5081
(Not Shown)
For all models.
PROPANE/NATURAL GAS CONVERSION KIT
THERMOSTATICALLY- CONTROLLED
BLOWER KIT - BKT
Provides better heat distribution. Blower turns off and on automatically, as needed. Complete installation and operation instructions
included in this manual.
(Not Shown)
PCDM-36C - Propane/LP Gas Conversion Kit
NCDM-36C - Natural Gas Conversion Kit
FACE/LOUVER PANEL KIT
(Not Shown)
FPD36 - Filligree Panel Kit - Black
FPD36B - Filligree Panel Kit - Brushed Brass
FPD36P - Filligree Panel Kit - Platinum
FPD36PB - Filligree Panel Kit - Polished Brass
RECEIVER AND HAND-HELD THERMOSTAT
REMOTE CONTROL KIT - GHRCTB SERIES
Allows the fireplace to be operated in a manually or thermostaticallycontrolled mode. You can adjust your heat settings and turn the
fireplace on or off without leaving the comfort of your easy chair.
LOUVER TRIM KIT (Rolled Louvers Only)
(Not Shown)
LT36B - Rolled Louver Trim Kit - Brushed Brass
LT36P - Rolled Louver Trim Kit - Platinum
LT36PB - Rolled Louver Trim Kit - Polished Brass
DEFLECTION HOODS
(Not Shown)
HD36 - Hood - Black (2" Brow)
PERIMETER TRIM KIT
(Not Shown)
PT36 - Perimeter Trim Kit - Black
PT36B - Perimeter Trim Kit - Brushed Brass
PT36P - Perimeter Trim Kit - Platinum
PT36PB - Perimeter Trim Kit - Polished Brass
RECEIVER AND HAND-HELD ON/OFF REMOTE
CONTROL KIT - GHRCB SERIES
Allows the fireplace to be turned on and off conveniently.
WALL MOUNTED THERMOSTAT CONTROL
KIT - GWMT1 (Not Shown)
Allows easy wall access for thermostatic operation of your fireplace.
WALL MOUNTED ON/OFF SWITCH - GWMS2
(Not Shown)
Allows burner system to be turned on and off with a wall switch.
For more information, visit www.desatech.com
111923-01B
37
37
OWNER'S REGISTRATION FORM
In order to provide better customer service for this and future purchases, we recommend that you register your product with us.
You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner’s
Registration Form and mail to the address on the back of this owner’s manual. Please provide the following product information:
Brand:
(Comfort Glow, Vanguard, etc.)
Model:
(EFP33PR, VTGH33NR, etc.)
Date Purchased:
Note: Keep receipt for warranty verification.
Serial Number:
7 or 9 digit number located on product or identification tag.
First Name:
Last Name:
Address:
City:
Home Phone:
State:
(
)
Zip:
Country:
-
E-Mail:
Please answer the following questions to register your product with DESA:
1.
Where will the product be used?
2.
If you bought this product yourself, did you plan to purchase this type of product before going into the store?
❍ Living/Family Room
❍ Office/Warehouse
❍ Utility Shed/Outbuilding
3.
Who selected the product? ❍ Male ❍ Female ❍ Both
4.
What is the population of your area? ❍ Under 10,000
❍ 100,000 to 250,000
❍ 10,000 to 25,000
❍ Bedroom
❍ 25,000 to 50,000
❍ Bathroom
❍ Propane (LP Gas)
❍ Fuel Oil
5.
What is your primary source of heat?
How was the product installed? ❍ Professional Installer
7.
Cost of product excluding sales tax? $___________________
8.
Cost to install product? $____________________
9.
Type of store where product was purchased? ❍ Hardware
❍ Fireplace or Hearth Shop
❍ Farm Store
❍ Self
❍ 50,000 to 100,000
❍ Emergency Back-Up Heat
❍ Propane Dealer
❍ Electric
❍ Natural Gas/Utility Co.
12. Level of Education of Purchaser: ❍ Some High School
❍ Relative or Friend
❍ Other
❍ Home Center/Builder’s Supply
❍ 40 - 49
14. Buyer’s total annual household income: ❍ Under $15,000
❍ 50 - 59
❍ D.I.Y. Home Project
❍ Construction Project
❍ Store Display
❍ Completed High School
❍ 30 - 39
❍ $75,000 to $99,999
❍ Replace Older Model
❍ Energy Savings/High Efficiency
11. How did you learn about this product brand? ❍ Advertising
❍ 20 - 29
❍ Natural Gas
❍ Other
❍ Heater was on Sale
13. Age of Purchaser: ❍ Under 20
❍ Wood
❍ Other
10. What motivated you to buy this product? ❍ Sudden Cold Weather
❍ Completed College
❍ $15,000 to $19,999
❍ $20,000 to $34,999
❍ $100,000 and Over
City: _______________________ State: __________
16. In choosing this product, how important were the following:
Not Important
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
visit
❍
❍
Somewhat Important
❍ Completed Graduate School
❍ 60 or Over
Name: ______________________________________
Availability
Price
Brand Name
Overall Quality
Heat Output
Made in USA
Warranty
Local Service
Value for Price
Prior Brand Experience
Controls Location
Thermostat, Remote, or Manual Operation
Ease of Operation
Special Features
Salesperson’s Recommendation
Friend/Relative’s Recommendation
For more information,
Portability
Quiet Operation
❍ Other
❍ Other ________________________
15. Store where product was purchased:
111923-01B
❍ Other
❍ Yes ❍ No
❍ Over 250,000
6.
❍ $50,000 to $74,999
❍ Garage
Very Important
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
www.desatech.com
❍
❍
❍
❍
❍ $35,000 to $49,999
TAPE
38
Postage
Required
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
For more information, visit www.desatech.com
TAPE
111923-01B
39
39
NOTES
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
For more information, visit www.desatech.com
111923-01B
40
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
LIMITED WARRANTY
DIRECT-VENT FIREPLACE
DESA warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase, provided that the
product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty
the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating
condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized
retailers of this product and/or DESA who will provide original factory replacement parts. Failure to use original factory replacement parts voids this
warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a
result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and
any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA’S LIABILITY IS HEREBY LIMITED
TO THE PURCHASE PRICE OF THE PRODUCT AND DESA SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER
INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
111923 01
NOT A UPC
111923-01
Rev. B
09/03
For more information, visit www.desatech.com
111923-01B
Download PDF

advertising