Installation manual | Desa (V)V36EP Outdoor Fireplace User Manual

DIRECT-VENT FIREPLACE
TM
OWNER’S OPERATION AND
INSTALLATION MANUAL
For more information, visit www.desatech.com
NATURAL GAS “VICTORIAN” MODEL (V)V36EN,
(V)V42EN SERIES
PROPANE/LP GAS “VICTORIAN” MODEL (V)V36EP,
(V)V42EP SERIES
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire
department.
WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property
damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer,
service agency, or the gas supplier.
— Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
— This appliance is only for use with
the type of gas indicated on the rating
plate. This appliance is not convertible
for use with other gases, unless a
certified kit is used.
This appliance may be installed in an aftermarket* manufactured (mobile) home, where not
prohibited by state or local codes.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
INSPECTING BURNERS .......................................................... 26
PRODUCT IDENTIFICATION ..................................................... 3
CLEANING AND MAINTENANCE ............................................ 27
LOCAL CODES ........................................................................... 3
TROUBLESHOOTING .............................................................. 28
PRODUCT FEATURES .............................................................. 4
REPLACEMENT PARTS .......................................................... 30
PRE-INSTALLATION PREPARATION ........................................ 4
SPECIFICATIONS .................................................................... 30
LOCATION OF TERMINATION CAP .......................................... 6
SERVICE HINTS ....................................................................... 30
VENTING INSTALLATION INSTRUCTIONS .............................. 7
TECHNICAL SERVICE ............................................................. 30
FIREPLACE INSTALLATION .................................................... 16
ACCESSORIES ........................................................................ 31
WIRING DIAGRAM ................................................................... 24
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 32
OPERATING FIREPLACE ........................................................ 25
WARRANTY INFORMATION ...................................... Back Cover
SAFETY INFORMATION
WARNINGS
WARNING: This product contains and/or generates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
IMPORTANT: Read this owner’s manual carefully
and completely before trying to assemble, operate, or
service this fireplace. Improper use of this fireplace
can cause serious injury or death from burns, fire,
explosions, electrical shock, and carbon monoxide
poisoning.
DANGER: Carbon monoxide poisoning may lead
to death!
This fireplace must be installed by a qualified (certified or licensed)
service person. It has a sealed gas combustion chamber that uses a
coaxial pipe (pipe within a pipe and having the same center) venting
system. It brings in fresh air for combustion through the outer pipe and
combustion gases are exhausted through the inner pipe. If the glass
door assembly and venting pipe are not properly seated, connected,
and sealed, carbon monoxide leakage (spillage) can occur.
Propane/LP gas and natural gas are both odorless. An odor-making
agent is added to each of these gases. The odor helps you detect a gas
leak. However, the odor added to these gases can fade. Gas may be
present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this fireplace.
WARNING: Any change to this fireplace or its
controls can be dangerous.
1.
2.
3.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the fireplace may not have been installed
properly. Get fresh air at once! Have fireplace inspected and
serviced by a qualified service person. Some people are more
affected by carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
4.
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
For propane/LP fireplace, do not place propane/LP supply
tank(s) inside any structure. Locate propane/LP supply tank(s)
outdoors. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier's instructions
• if you cannot reach you gas supplier, call the fire department.
Never install the fireplace
• in a recreational vehicle
• in windy or drafty areas where curtains or other combustible
(flammable) objects can make contact with the fireplace front
• in high traffic areas
For more information, visit www.desatech.com
108862-01D
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
SAFETY INFORMATION
3
3
PRODUCT IDENTIFICATION
Continued
Upper Louver
5.
6.
7.
8.
9.
10.
11.
12.
13.
This fireplace reaches high temperatures. Keep children and
Panel
Flue Collar
adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they are in the room
with fireplace.
Nailing
Do not modify this fireplace under any circumstances. Any Flange
parts removed for servicing must be replaced prior to operating fireplace.
Log
Turn fireplace off and let cool before servicing, installing, or
Set
repairing. Only a qualified service person should install, ser- Glass
vice, or repair this fireplace. Have fireplace inspected annu- Door
Assembly
ally by a qualified service person.
You must keep control compartments, burners, and circulatLava
ing air passages clean. More frequent cleaning may be needed
Rock
due to excessive lint and dust from carpeting, bedding material, etc. Turn off the gas valve and pilot light before cleaning
fireplace.
Have venting system inspected annually by a qualified service Control
person. If needed, have venting system cleaned or repaired. Valve
Grate
See Cleaning and Maintenance, page 27.
Assembly
Lower
Keep the area around your fireplace clear of combustible maLouver Glowing
Panel Embers
terials, gasoline, and other flammable vapor and liquids. Do
not run fireplace where these are used or stored. Do not place
ON/OFF/REMOTE Switch
Blower Switch
items such as clothing or decorations on or around fireplace.
(Optional Installation)
(Optional Installation)
Do not use this fireplace to cook food or burn paper or other
Figure 1 - Victorian Direct-Vent Fireplace with Electronic Ignition
objects.
Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this fireplace. Use only the gas type indicated on fireplace
nameplate.
This appliance, when installed, must be electrically grounded Install and use fireplace with care. Follow all local codes. In the
in accordance with local codes or, in the absence of local codes, absence to local codes, use the current National Fuel Gas Code
with the National Electrical Code, ANSI/NFPA 70, or the Ca- ANSI Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Instalnadian Electrical Code, CSA C22.1.
lation Code (Canada).
Do not use fireplace if any part has been exposed to or under *Available from:
water. Immediately call a qualified service person to arrange
American National Standards Institute, Inc.
for replacement of the unit.
1430 Broadway
New York, NY 10018
Do not operate fireplace if any log is broken.
National Fire Protection Association, Inc.
Do not use a blower insert, heat exchanger insert, or other acBatterymarch Park
cessory not approved for use with this fireplace.
Quincy, MA 02269
Do not operate fireplace with glass door removed, cracked, or
broken.
Provide adequate clearances around air openings.
LOCAL CODES
14.
15.
16.
17.
18.
19.
For more information, visit www.desatech.com
108862-01D
4
PRODUCT FEATURES
PRE-INSTALLATION PREPARATION
Location and Space Requirements
PRODUCT FEATURES
These are a few facts that can help you understand and enjoy your
direct-vent fireplace:
• The venting system may be routed to the outside of your home
in several ways. It may vent through the roof (vertical) or it may
vent to an outside/exterior wall (horizontal). The vent pipe installation is very important to allow for proper operation. You
must follow the venting instructions very carefully for either
vertical or horizontal applications.
• This fireplace may be installed in any room of your house provided
all local codes and these installation instructions are followed.
• This fireplace does not require electricity to operate.
• Only the blower requires electricity if installed and if you plan
to install the blower at a later date, do not forget to wire the
outlet at the bottom of the fireplace when framing.
• A piezo ignitor and ceramic electrode create spark to ignite the
pilot light. It does not require any matches, batteries or any other
sources of ignition to light the pilot.
• Each time you turn on your fireplace, you may notice some
amount of condensation on the inside of the fireplace glass. This
is normal and will disappear after 10-20 minutes of operation.
• Your direct-vent gas fireplace system (fireplace and venting) is a
balanced and sealed gas operating unit. It requires approximately
10-20 minutes of operating time before the flame pattern stabilizes.
PRE-INSTALLATION
PREPARATION
• Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against
any exterior surface on the back, sides, or top of your fireplace,
except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be
placed directly against wall or framing material. See framing
details on page 5.
• If you plan on installing a television or entertainment center recessed above your fireplace, it is recommended that you maintain a minimum 18" above top of louver opening.
• When locating termination cap, it is important to observe the
minimum clearances shown in Figure 7, page 6.
• If recessing into a wall, you can avoid extra framing by positioning your fireplace against an already existing framing member.
• Do not recess termination cap into a wall or siding.
• You may paint the termination cap with 450ºF (232ºC) heatresistant paint to coordinate with the exterior finish.
• There must not be any obstruction such as bushes, garden sheds,
fences, decks, or utility buildings within 24" from the front of
the termination cap.
• Do not locate termination cap where excessive snow or ice build
up may occur. Be sure to clear vent termination area after snow
falls to prevent accidental blockage of venting system. When
using snow blowers, do not direct snow towards vent termination area.
LOCATION AND SPACE REQUIREMENTS
Determine the safest and most efficient location for your DESA
International direct-vent fireplace. Make sure that rafters and wall
studs are not in the way of the venting system. Choose a location
where the heat output is not affected by drafts, air conditioning
ducts, windows or doors. Figure 2 shows some common locations.
Be aware of all restrictions and precautions before deciding the
exact location for your fireplace and termination cap.
When deciding the location of your fireplace, follow these rules:
• Do not connect this fireplace venting to a chimney flue serving
a separate solid-fuel burning fireplace or appliance.
• Due to high temperatures, do not locate this fireplace in high traffic areas, windy or drafty areas, or near furniture or draperies.
• Proper clearances must be maintained.
• If your fireplace is to be installed directly on carpeting, vinyl
tile, or any combustible material other than wood, it must be
installed on a metal or wood panel extending the full width and
depth of the fireplace. See Figure 3.
Flush with a wall
Through exterior wall
enclosed in a chase
Corner
installation
Figure 2 - Common Fireplace Locations
RW
D
FW
Fireplace size
D x FW x RW
36"
21 1/8" 41"
29"
42"
23 1/4" 48" 36 1/4"
Figure 3 - Fireplace Bottom Dimensions
For more information, visit www.desatech.com
108862-01D
PRE-INSTALLATION PREPARATION
Clearances
Framing and Finishing
5
5
PRE-INSTALLATION
PREPARATION
Continued
CLEARANCES
Minimum clearances to combustibles for the fireplace are as follows:
Back, and sides
0"/mm
Perpendicular walls
6" (152mm)
Floor
0"/mm
Ceiling to louver opening 42" (1067mm)
Front
36" (914mm)
Top
0"/mm
Vent
(See venting instructions for
specific venting clearances.)
Combustible material with a maximum thickness of 5/8" may be
flush with the top front of fireplace .
NOTICE: This fireplace is intended for use as supplemental heat. Use this fireplace along with your primary heating system. Do not install this fireplace as
your primary heat source. If you have a central heating system, you may run system’s circulating blower
while using fireplace. This will help circulate the heat
throughout the house. In the event of a power outage,
you can use this fireplace as a heat source.
D
B
C
A
E
F
G
Nailing Tabs
H
A
B
C
D
E
F
G
H
36" Models 42" Models
41 5/8"
35 3/4"
15"
21 5/8"
58 1/2"
49 5/8"
10 3/8"
13 1/2"
16 3/4"
13 3/4"
41"
48"
48 1/4"
41 1/4"
81 1/2"
68 1/2"
Figure 5 - Framing Clearances for Corner Installation
FRAMING AND FINISHING
1
Figure 4 shows typical framing of this fireplace. Figure 5 shows
framing for corner installation. All minimum clearances must be met.
2
3
A
For available accessories for this fireplace, see Accessories on page
31. If you are using a separate combustible mantel piece, refer to
Figure 6 for proper installation height. You can install noncombustible mantels at any height above the fireplace. Note: Noncombustible mantels may discolor!
A
B
C
4
B
Wall
5
C
6
D
E
7
F
36" Models 42" Models
40 1/8"
36 1/8"
41 1/4"
48 1/4"
1
25 5/8"
23 /2"
G
Top of Louver Opening
Ref. Mantel Depth Ref. Mantel from Top
of Louver Opening
A
B
C
Figure 4 - Framing Clearances for Installation Against an Exterior
Wall
1
2
3
4
5
6
7
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
2" (51mm)
A
B
C
D
E
F
G
16" (406mm)
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
Figure 6 - Clearances for Combustible Mantels
For more information, visit www.desatech.com
108862-01D
6
LOCATION OF TERMINATION CAP
LOCATION OF TERMINATION CAP
N
N
D
H
V
L
E
B
C
Fixed
Closed
F
B
Openable Fixed
Closed
V
Openable
V
I
V
G
B
V
B
B
J
X
V
G
G
M
A
V
K
X
V
A
V TERMINATION CAP
A = clearance above grade, veranda, porch, deck, or balcony
[*12 inches (305mm) minimum]
B = clearance to window or door that may be opened
[12 inches (305mm) minimum]
C = clearance to permanently closed window [minimum 12 inches
(305mm) recommended to prevent condensation on window]
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (610mm) from the
center-line of the terminal [18 inches (457mm) minimum]
E = clearance to unventilated soffit [12 inches (305mm) minimum]
F = clearance to outside corner (see below)
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly within
36 inches (914mm) horizontally from the center-line of the regulator
I =
J =
K =
L =
M=
N =
G GAS METER
RESTRICTED AREA
(TERMINATION PROHIBITED)
clearance to service regulator vent outlet [*72 inches (1829mm)
minimum]
clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other fireplace [*12 inches (305mm)
minimum]
clearance to a mechanical air supply inlet [*72 inches (1829mm)
minimum]
† clearance above paved side-walk or a paved driveway located on
public property [*84 inches (2133mm) minimum]
clearance under veranda, porch, deck [*12 inches (305mm) minimum ‡]
clearance above a roof shall extend a minimum of 24 inches (610mm)
above the highest point when it passes through the roof surface and
any other obstruction within a horizontal distance of 18 inches (457mm)
X AIR SUPPLY INLET
† vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
*
as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.
Note: Local codes or regulations may require different clearances
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Inside Corner
Outside Corner
Recessed Location
D
C
A
C
A = 6" (152mm)
E
V
V
V
B = 6" (152mm)
B
Balcony with No Side Wall
Balcony with Perpendicular Side Wall
H
G
V
V
J
G = 12" (305mm) minimum clearance
Combustible &
Noncombustible
H = 24" (610mm)
J = 20" (508mm)
C = Maximum depth of 48" (1219mm) for
recessed location
D = Minimum width for back wall of
recessed location Combustible - 38" (965mm)
Noncombustible - 24" (610mm)
E = Clearance from corner in
recessed locationCombustible - 6" (152mm)
Noncombustible - 2" (51mm)
Figure 7 - Minimum Clearances for Termination Cap
For more information, visit www.desatech.com
108862-01D
VENTING INSTALLATION INSTRUCTIONS
Installation Precautions
7
7
VENTING INSTALLATION
INSTRUCTIONS
NOTICE: Read these instructions completely before attempting installation.
These models are tested and approved for use with DESA International (direct-vent) pipe components and terminations.
The venting system must terminate on the outside of the structure and
can not be attached to a chimney or flue system serving a separate
solid fuel or gas burning appliance. A direct-vent appliance must have
its own venting system. DO NOT common vent this appliance.
These models are approved to be vented either horizontally through
an outside wall or vertically through a roof or chase enclosure using
the following guidelines:
• When venting system terminates horizontally on an outside wall,
you must install a standoff if the termination cap is to be installed directly on a combustible finish such as vinyl, wood,
stucco, etc.
• Never run the vent downward as this may cause excessive temperatures which could cause a fire.
• Vent pipe air space clearances to combustibles are 1" on all sides
except on the horizontal sections, which requires 2" clearance
from the top of the pipe. Where the termination cap penetrates a
combustible wall, 1" air space clearance is required.
• Snorkel terminations are required when minimum clearance to grade
cannot be met (see Figure 16 on page 11).
• Have fireplace and selected vent components on hand to help
determine the exact measurements when elbowing or offsetting.
Always use wall firestops when penetrating walls and firestops
when penetrating ceilings or attic spaces.
• Install horizontal venting with a 1/4" rise for every 12" of run
toward the termination.
NOTICE: Failure to follow these instructions will void
the warranty.
INSTALLATION PRECAUTIONS
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
• Installation of any damaged venting component
• Unauthorized modification of the venting system (Do not cut
or alter vent components)
• Installation of any component part not manufactured or approved by DESA International
• Installation other than as instructed by these instructions
WARNING: This gas fireplace and vent assembly
must be vented directly to the outside. The venting
system must NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each
direct-vent gas appliance must use a separate vent
system. Do not use common vent systems.
WARNING: Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal
sections, which require 2" clearances from the top of
the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
do so could result in serious injury, property damage
or loss of life.
For more information, visit www.desatech.com
108862-01D
8
VENTING INSTALLATION INSTRUCTIONS
Installation Planning
VENTING INSTALLATION
INSTRUCTIONS
Continued
INSTALLATION PLANNING
There are two basic types of direct-vent installation:
• Horizontal Termination
• Vertical Termination
Female
Locking
Lugs
Male
Slots
Horizontal Termination Installation
IMPORTANT: Horizontal square terminations require only inner
portion of wall firestop. Horizontal installations using round termination require exterior portion of wall firestop available only in vent
kit 01491 (see Figure 14, page 10).
1. Set the fireplace in its desired location and determine the route
your horizontal venting will take. Do not secure the fireplace
until all venting has been installed. Some installations require
sliding the fireplace in and out of position to make final venting connections. Figures 14 through 18 on pages 10 through
12 show different configurations for venting with horizontal
termination that will help you decide which application best
suits your installation. Check to see if wall studs or roof rafters
are in the path of your desired venting route. If they are, you
may want to adjust the location of the fireplace.
2. Direct vent pipe sections and components are designed with
special twist-lock connections.
Twist-Lock Procedure: The female ends of the pipes have
locking lugs (indentations). These lugs will slide straight into
matching slots on the male ends of adjacent pipes. Push pipe
sections together and twist one section clockwise approximately one-quarter turn until the sections are fully locked
(see Figure 8). Note: Horizontal runs of vent must be supported every three feet. Use wall straps for this purpose.
3. Use a 45° elbow to connect venting system to fireplace flue collar. The elbow is designed to be twist-locked onto the flue collar
as described in step 2. IMPORTANT: Do not attempt to alter the
configuration of the elbow by cutting, twisting, bending, etc.
4. Assemble the desired combination of pipe and elbows to the
fireplace flue collar. If there are long portions of venting run,
pre-assembled pipe sections may be installed as subassemblies
for convenience.
5. Carefully determine the location where the vent pipe assembly
will penetrate the outside wall. The center of the hole should line
up with the center-line of the horizontal vent pipe. Mark the wall
for a 10 3/4" x 10 3/4" square hole. Cut and frame the square hole in
the exterior wall where the vent will be terminated. If the wall
being penetrated is constructed of noncombustible material, such
as masonry block or concrete, a 8 1/2" hole with zero clearance is
acceptable (see Figure 9).
Figure 8 - Vent Pipe Connections
Vent Opening
Combustible Wall
10 3/4"
(273mm)
10 3/4" Inside Framing
(273mm)
10 3/4"
(273mm)
Vent Opening
Noncombustible Wall
(Framing
Detail)
8 1/2"
(216mm)
Center
of Hole
Figure 9 - Vent Opening Requirements
For more information, visit www.desatech.com
108862-01D
VENTING INSTALLATION INSTRUCTIONS
9
9
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
WARNING: Do not recess vent termination into
any wall. This will cause a fire hazard.
6.
7.
8.
Cut Siding Away
to Fit Standoff
Standoff
Noncombustible Exterior Wall: Position the horizontal vent
cap in the center of the 8 1/2" round hole and attach to the exterior wall with four wood screws provided. Before attaching
the vent cap to exterior wall, run a bead of non-hardening mastic
(pliable sealant) around the outside edges to make a seal between it and the outside wall. Note: The four wood screws
provided should be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of sidings.
Combustible Exterior Wall: For vinyl siding, stucco, or wood
exteriors, a siding standoff must be installed between the vent
cap and exterior wall. The siding standoff prevents excessive
heat from damaging the siding materials. Siding material must
be cut to accommodate standoff. Bolt the vent cap to the standoff. Apply non-hardening mastic around outside edge of standoff. Position the standoff/cap assembly in the center of the 10
3
/4" square hole and attach to exterior wall with wood screws
provided (see Figure 11). The siding standoff must sit flush
against the exterior fascia material.
Slide the wall firestop over the vent pipe before connecting
horizontal run to vent cap (see Figure 12).
Carefully move fireplace, with vent assembly attached, toward
wall and insert vent pipe into horizontal termination. The pipe
overlap should be a minimum of 11/4".
Wood Screw
Vent Cap
Screws
Apply Mastic
to All Four Sides
Figure 11 - Installing Siding Standoff
Interior Wall
Surface
Wall
Firestop
Vent Cap
(Horizontal
Termination)
Horizontal
Vent Pipe
Apply Mastic to
All Four Sides
Screw
Vent Cap
Figure 12 - Connecting Vent Cap with Horizontal Vent Pipe
Wood Screw
Figure 10 - Installing Horizontal Vent Cap
For more information, visit www.desatech.com
108862-01D
10
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
9.
Slide wall firestop against interior wall surface and attach with
screws provided. See Figure 13 for horizontal termination details.
10. Place fireplace into position and shim with noncombustible material if needed. Nail or screw side flanges to framing to secure
unit in place. IMPORTANT: Make sure fireplace is level before
securing. If fireplace is not level it will not work properly.
WARNING: Never run vent downward as this may
cause excessive temperatures which could cause a
fire. Operation of improperly installed and maintained venting system could result in serious injury,
property damage or loss of life.
GROUND FLOOR INSTALLATION
Minimum Pipe
Overlap 11/4"
Siding Standoff
Screws
Direct Vent
Pipe
Recommended Applications:
• Installation using cabinet surrounds
• Through the wall using round or square termination
(up to 12" horizontal pipe)
• NOT FOR CORNER INSTALLATION
45° Elbow
Wall
Firestop
Horizontal High
Wind Square
Termination
Adjustable
Pipe 12" Max.
Wall
Firestop
Maintain 1"
Minimum Air
Space Around
Outer Pipe When
Penetrating a Wall
Square Termination
High Wind
Termination
10 3/4" x 10 3/4"
Framed
Opening
Apply Mastic to
Outside Edge of
Standoff
Exterior Wall
with Vinyl Siding
V36 Series
V42 Series
Vertical (V)
Horizontal (H)
32 3/4"
17" max.
3
17" max.
36 /4"
45° Elbow
Wall
Firestop
Exterior Portion of Wall
Firestop (Round
Termination Only)
Figure 13 - Typical Horizontal Termination Cap Mounting with
Additional Siding Standoff Installed
Horizontal Termination Configurations
Horizontal
Round
Termination
Figures 14 through 18 show different configurations and alternatives
for venting with horizontal termination. Each figure includes a chart
with critical minimum and maximum dimensions which MUST be
met. IMPORTANT: Remember that a horizontal run of venting must
have a 1/4" rise for every 12" of run toward the termination.
Round Termination
(Kit 01491 Shown)
Figure 14 - Horizontal Termination Configuration for Square or
Round Termination
For more information, visit www.desatech.com
108862-01D
VENTING INSTALLATION INSTRUCTIONS
11
11
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
CORNER INSTALLATION
Recommended Applications:
• Corner ground floor installation
• Ground floor installation where pipe vents horizontally through wall
(over 12" horizontal pipe)
• Basement installation where one foot clearance from ground to
termination is possible
Not to Exceed
(H) Limits
Horizontal (H) (36"/42")
30" max.
48" max.
60" max.
84" max.
20' max.
* Ground Floor Corner Venting
Not to Exceed
(H) Limits
90° Elbow
90° Elbow
Square
Termination
Wall
Firestop
Vertical (V)
Required
36"
42"
Vertical Pipe
None
*43 1/2" min. 46 1/4" min.
1 ft.
54 1/2" min. 57 1/4" min.
2 ft.
66 1/2" min. 69 1/4" min.
3 ft.
78 1/2" min. 81 1/4" min.
4 ft.
90 1/2" min. 93 1/4" min.
Square
Termination
As Required for (V)
See Chart for Pipe
Section Required
Wall
Firestop
12" Minimum
45°
Elbow
45° Elbow
Figure 15 - Horizontal Termination Configuration for Corner Installation Using One 90° Elbow
SNORKEL TERMINATION INSTALLATION
Recommended Applications:
• Installations requiring a vertical rise on building exterior
• Any installation using snorkel termination to achieve one foot above ground
Snorkel terminations are available for installations requiring a vertical rise on the exterior of the building. If
installing snorkel termination below grade, you must provide proper drainage to prevent water from entering snorkel
termination (see Figure 16). Do not back fill around snorkel termination.
Snorkel
Termination
Snorkel
Termination
90° Elbow
12"
Minimum
12"
Minimum
Wall
Firestop
45°
Elbow
Adequate
Drainage
Figure 16 - Snorkel Termination Configurations for Below Ground Installation
For more information, visit www.desatech.com
108862-01D
Snorkel
Termination
12"
Minimum
12
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
HORIZONTAL SYSTEM INSTALLATION USING TWO 90°
ELBOWS
The following configurations show the minimum vertical rise
requirements for a horizontal system using two 90° elbows.
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45°Elbow
6' max.
12' max.
18' max.
20' max.
20' max.
Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
6' max.
12' max.
18' max.
20' max.
20' max.
45° Elbow
Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace
For more information, visit www.desatech.com
108862-01D
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination
13
13
VENTING INSTALLATION
INSTRUCTIONS
Continued
INSTALLATION FOR VERTICAL TERMINATION
Note: Vertical restrictor must be installed in all vertical installations.
1. Determine the route your vertical venting will take. If ceiling
joists, roof rafters, or other framing will obstruct the venting
system, consider an offset (see Figure 19) to avoid cutting load
bearing members. Note: Pay special attention to these installation instructions for required clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, etc. Do not pack air spaces with insulation.
Also note maximum vertical rise of the venting system and
any maximum horizontal offset limitations.
2. Set the fireplace in desired location. Drop a plumb line down
from the ceiling to the position of the fireplace exit flue. Mark
the center point where the vent will penetrate the ceiling. Drill
a small locating hole at this point.
Drop a plumb line from the inside of the roof to the locating
hole in the ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
Roof Flashing
Wall Strap
45° Elbow
Ceiling Firestop
Figure 19 - Offset with Wall Strap and 45° Elbows
2.
Assemble the desired lengths of pipe and elbows necessary to
reach from the fireplace flue up through the firestop. Be sure
all pipe and elbow connections are fully twist-locked (see Figure 8, page 8).
3. Cut a hole in the roof using the locating hole as a center point.
(Cover any exposed open vent pipes before cutting hole in roof.)
The 10 3/4"x10 3/4" hole must be measured on the horizontal;
actual length may be larger depending on the pitch of the roof.
There must be a 1" clearance from the vent pipe to combustible
materials. Frame the opening as shown in Figure 9, page 8.
4. Connect a section of pipe and extend up through the hole.
Note: If an offset is needed to avoid obstructions, you must
support the vent pipe every 3 feet. Use wall straps for this
purpose (see Figure 19). Whenever possible, use 45° elbows
instead of 90° elbows. The 45° elbow offers less restriction to
the flow of the flue gases and intake air.
5. Place the flashing over the pipe section(s) extending through
the roof. Secure the base of the flashing to the roof and framing with roofing nails. Be sure roofing material overlaps the
top edge of the flashing as shown in Figure 19. There must be
a 1" clearance from the vent pipe to combustible materials.
6. Continue to add pipe sections until the height of the vent cap
meets the minimum building code requirements described in
Figure 7 on page 6. Note: You must increase vent height for
steep roof pitches. Nearby trees, adjoining rooflines, steep
pitched roofs, and other similar factors may cause poor draft
or down-drafting in high winds. Increasing the vent height may
solve this problem.
7. Twist-lock the vent cap onto the last section of vent pipe.
Note: If the vent pipe passes through any occupied areas above the first
floor, including storage spaces and closets, you must enclose pipe. You
may frame and sheetrock the enclosure with standard construction
material. Make sure and meet the minimum allowable clearances to
combustibles. Do not fill any of the required air spaces with insulation.
If area above is a room, install
firestop above framed hole.
Flat Ceiling Installation
1.
Cut a 10 3/4" square hole in the ceiling using the locating hole as
a center point. The opening should be framed to 10 3/4"x10 3/4"
(273 mm x 273 mm) inside dimensions, as shown in Figure 9
on page 8 using framing lumber the same size as the ceiling
joists. If the area above the ceiling is an insulated ceiling or a
room, nail firestop from the top side. This prevents loose insulation from falling into the required clearance space. Otherwise,
install firestop below the framed hole. The firestop should be
installed with no less than three nails per side (see Figure 20).
Figure 20 - Installing Firestop
For more information, visit www.desatech.com
108862-01D
If area above is not a room, install
firestop below framed hole.
14
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
Vertical Termination Configurations
Venting with One 90° Elbow
Figures 21 through 24 show four different configurations for vertical termination.
Venting with Two 90° Elbows
Vertical (V)
5' min.
6' min.
7' min.
8' min.
20' max.
45° Elbow
Horizontal (H1) +
Horizontal (H2)
2' max.
4' max.
6' max.
8' max.
8' max.
Vertical (V)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
Note: Install restrictor
into inner collar of
fireplace as shown.
Note: Install
restrictor into
inner collar of
fireplace as
shown.
Figure 22 - Vertical Venting Configuration Using One 90° Elbow
(Vertical Round High Wind Termination Shown)
Venting with Two 90° Elbows
Figure 21 - Vertical Venting Configuration Using Two 90° Elbows
with Two Horizontal Runs (Vertical Round High Wind Termination
Shown)
Vertical (V1)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
6' max.
12' max.
18' max.
20' max.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Note: Vertical (V1) + Vertical (V2) = 40' max.
Figure 23 - Vertical Venting Configuration Using Two 90° Elbows
(Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
108862-01D
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
High Altitude Installation
15
15
VENTING INSTALLATION
INSTRUCTIONS
Continued
HIGH ALTITUDE INSTALLATION
Vertical Venting
V = 40' max.
Your DESA International direct-vent fireplace has been CSA tested
and approved for elevations from 0-2000 feet (USA) and elevations
from 0-4500 feet (Canada) .
When installing this fireplace at an elevation above 2000 feet (in the
USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet above sea level. Check with your local gas company for
proper orifice size identification.
When installing this fireplace at an elevation above 4500 feet (in
Canada), check with local authorities.
Consult your local gas company to help determine the proper orifice
for your location.
For assistance with any high altitude installation contact DESA
International’s Customer Service Department at 1-866-672-6040.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Figure 24 - Vertical Venting Configuration With No Horizontal
Run (Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
108862-01D
16
VENTING INSTALLATION INSTRUCTIONS
Parts Lists for Venting Kits and Components
FIREPLACE INSTALLATION
Check Gas Type
Installing Optional Blower Accessory
VENTING INSTALLATION
INSTRUCTIONS
Continued
PARTS LISTS FOR VENTING KITS AND
COMPONENTS
DESA International Venting Accessories
DESA International (5/8") Pipe & Vent Kits
Number Description
Horizontal Round Termination Kit
01504
01505
01506
01507
01508
01514
01607
VR-58
Includes: Round Termination, Wall Firestop, and
45° Elbow (Through 5" Wall)
FIREPLACE INSTALLATION
01497
01498
12" Section Coaxial Pipe - Galvanized (4)
18" Section Coaxial Pipe - Galvanized (4)
CHECK GAS TYPE
01499
24" Section Coaxial Pipe - Galvanized (4)
01500
36" Section Coaxial Pipe - Galvanized (4)
01501
48" Section Coaxial Pipe - Galvanized (4)
01513
01606
6" Section Coaxial Pipe - Galvanized (4)
Adjustable 17"-24" Section Coaxial Pipe Galvanized (4)
F8030
Adjustable 7"-12" Section Coaxial Pipe - Galvanized (6)
D1032
Adjustable 7"-12" Section Coaxial Pipe - Galvanized (1)
Number Description
01492
Horizontal Square Termination Kit
Includes: 45° Elbow (Through 5" Wall), Wall Firestop,
Horizontal Square Termination
01493
Basic Vertical Termination Kit
Includes: Vertical Termination, Adjustable Flashing,
Storm Collar
01491
DESA International Elbows
Number Description
01502
45° Elbow - Galvanized (4)
01503
90° Elbow - Galvanized (4)
DESA International Terminations
Number Description
01494
Vertical Round Termination - Galvanized (1)
01495
Horizontal Round Termination - Galvanized (1)
01496
01798
01800
01801
Horizontal Square Termination - Galvanized (1)
Vertical Round High Wind Termination (1)
Horizontal Square High Wind Termination (1)
14" Snorkel Termination - Galvanized (1)
01802
36" Snorkel Termination - Galvanized (1)
Firestop Plate (4)
Adjustable Roof Flashing 0 to 8/12 - Galvanized (6)
Steep Pitch Flashing 9/12 to 12/12 - Galvanized (6)
Storm Collar - Galvanized (4)
Wall Strap (4)
Combustible Siding Standoff - Galvanized (1)
Wall Firestop - Galvanized (4)
Vertical Restrictor - Galvanized
Use proper gas type for the fireplace unit you are installing. If you
have conflicting gas types, do not install fireplace. See retailer
where you purchased the fireplace for proper fireplace according to
your gas type.
INSTALLING OPTIONAL BLOWER
ACCESSORY
NOTICE: If installing blower in an existing fireplace
with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex electrical outlet
installed in the right side of the bottom of the fireplace
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
Model BK Installation
Follow all instructions provided in the blower accessory kit.
1. Attach the power cord to the blower motor by firmly pushing the
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25, page 17).
2. Attach green ground wire from power cord to blower housing using screw provided (see Figure 25, page 17). Tighten
screws securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward. The blower
will fit inside the back opening and be held in position against
the back wall by the magnets (see Figure 25, page 17).
For more information, visit www.desatech.com
108862-01D
FIREPLACE INSTALLATION
Installing Optional Blower Accessory (Cont.)
17
17
FIREPLACE INSTALLATION
Continued
4.
5.
6.
7.
8.
Speed Control
Switch
Bracket
Blower
Plug-In
Control
Knob
Locknut
Control
Shaft
Duplex Outlet
(Located underneath
firebox floor against
lower right outside wall)
Figure 26 - Attaching Speed Control to Firebox
B
ol
w M
re oto
r
V F
ira na
ba S
el tiw
hc
Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green
ground wire is tight.
Mount speed control box to switch bracket by placing the plastic
control shaft forward through the opening in the switch bracket
(see Figure 26).
While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it
is tight against front panel. Place control knob provided on shaft.
Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
Plug in blower power cord.
a. If your firebox is installed as a freestanding unit with an
accessory mantel, determine whether the power cord will
exit the left side or the right side of the firebox. Route power
cord through exit hole and plug the power cord into a wall
receptacle near the firebox.
b. If your firebox installation is recessed and/or pre-wired,
plug the power cord into the duplex outlet provided. Refer
to your firebox owner’s manual for instructions on wiring
the duplex outlet.
nO
ffO
k
ca
kc lB
al
B
B
al
kc W
ih
et
1
01
1/ .V
51 C.A
.
B
al
kc hW
i
et erG
ne
CAUTION: Never touch the blower wheel while in
operation.
9.
Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Turn blower on and check for operation. Turn blower off
by turning knob fully counterclockwise before continuing.
10. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27).
Wiring Diagram Decal
12" in Front of Blower
Figure 27 - Location of Wiring Diagram Decal (Model May Vary
From Illustration)
Blower
Location
Lower Firebox
Cavity
Magnetic Strips
Side View
Exhaust
Port
Spade Terminals
Green
Ground Wire
Screw
Figure 25 - Blower Model BK
For more information, visit www.desatech.com
108862-01D
FIREPLACE INSTALLATION
18
Installing Optional Blower Accessory (Cont.)
FIREPLACE INSTALLATION
Continued
Model BKT Installation
Note: When installing the BKT thermostatically-controlled blower,
you must first secure the thermal switch bracket to the blower if it
has not already been factory installed.
1. Place the green ground wire with ring terminal between the
bottom hole on the thermal switch bracket and the top ear hole
on the blower assembly. Insert the phillips screw into all three
pieces and tighten securely (see Figure 28, page 18).
2. Connect wire harness and power cord terminals. Connect the
blue jumper wire to the blower motor terminal and the right
side terminal of the thermal switch. Connect the black wire to
the left side of the thermal switch and the white wire to the
other remaining blower motor terminal.
Note: The power cord outer insulation sleeve may have to be
stripped slightly to allow enough wire length to reach and make all
connections. DO NOT trim excessive length away. Just enable
enough to make all connections securely.
3. Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward and the thermodisc
positioned up near the fireplace bottom. The thermodisc must be
oriented near the fireplace bottom as shown in Figure 28 in order
to sense temperature and properly operate. The blower will be
held in position against the back wall by the magnets incorporated onto the blower housing (see Figure 28).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and thermal switch, and that the screw
for the thermodisc bracket and green ground wire is tight.
White Wire
Blue Wire
Power Cord
Thermal
Switch
Bracket
Mount the speed control box against the mounting plate provided in the lower fireplace cavity by placing the plastic control
shaft forward through the round hole (see Figure 26, page 17).
6. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it is tight against mounting plate. Place control knob provided on shaft (see Figure 26, page 17).
7. Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Also double check all wire leads and make sure wire routing is not pinched or in a precarious position. Correct accordingly.
8. Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
9. Plug in blower power cord to duplex outlet.
10. The blower will only run when the speed control knob is in the
ON position and the thermal switch senses temperature after
the fireplace begins to heat up. The blower speed can be adjusted by rotating the control knob. To turn off, turn knob fully
counterclockwise until it clicks off. If the blower is ON and
has been running with the fireplace operating, the blower will
continue to run for a short time after the fireplace has been
turned off. As the thermal switch cools down, the blower shuts
down automatically.
11. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27, page 17).
.
Blower Wiring Diagram
Magnetic
Strips
Air Flow
Direction
Black
Wire
5.
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
Variable
Fan Switch
Phillips
Screw
Thermal Switch
Route BKT
Blower Through
This Area
Ring Terminal
on Green Wire
Air Flow Direction
Magnets
Thermodisc
Side View Firebox Bottom
Figure 28 - Blower Model BKT
Off
Fan Switch
(N.O.)
1
2
Black
On
Blue
110/115
V.A.C.
Black
White
Green
Blower
Location
Blower
Motor
Figure 29 - Blower Wiring Diagram for Thermostat-Controlled
Models
For more information, visit www.desatech.com
108862-01D
FIREPLACE INSTALLATION
Installing Gas Piping to Fireplace Location
19
19
FIREPLACE INSTALLATION
Continued
INSTALLING GAS PIPING TO FIREPLACE
LOCATION
WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.
CAUTION: For propane/LP units, never connect
fireplace directly to the propane/LP supply. This
heater requires an external regulator (not supplied).
Install the external regulator between the fireplace
and propane/LP supply.
Installation Items Needed
Before installing fireplace, make sure you have the items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local codes)
* A CSA design-certified equipment shutoff valve with 1/8" NPT tap
is an acceptable alternative to test gauge connection. Purchase the
CSA design-certified equipment shutoff valve from your retailer.
For propane/LP connection only, the installer must supply an
external regulator. The external regulator will reduce incoming gas
pressure. You must reduce incoming gas pressure to between 11 and
14 inches of water. If you do not reduce incoming gas pressure,
fireplace regulator damage could occur. Install external regulator
with the vent pointing down as shown in Figure 31. Pointing the vent
down protects it from freezing rain or sleet.
External
Regulator
Propane/LP
Supply Tank
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to fireplace.
If pipe is too small, undue loss of volume will occur.
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from fireplace (see Figure 31).
IMPORTANT: Install main gas valve (equipment shutoff valve) in
an accessible location. The main gas valve is for turning on or
shutting off the gas to the appliance.
Check your building codes for any special requirements for locating
equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 31. Locate sediment trap/drip leg where it
is within reach for cleaning. Install in piping system between fuel
supply and fireplace. Locate sediment trap/drip leg where trapped
matter is not likely to freeze. A sediment trap traps moisture and
contaminants. This keeps them from going into fireplace gas controls. If sediment trap/drip leg is not installed or is installed wrong,
fireplace may not run properly.
CSA Design-Certified
Equipment Shutoff Valve
with 1/8" NPT Tap*
Approved Flexible
Gas Line
3" Minimum
Vent
Pointing
Down
Cap
Figure 31 - Gas Connection
Figure 30 - External Regulator with Vent Pointing Down
(Propane/LP Only)
Pipe Nipple
Tee Joint
Sediment Trap/Drip Leg
* The CSA design-certified equipment shutoff valve may be supplied with the appliance or you can purchase it from your retailer.
For more information, visit www.desatech.com
108862-01D
Natural - From
Gas Meter (5.5"
W.C. to 10.5"
W.C. Pressure)
Propane/LP
From External
Regulator (11"
W.C. to 14"
W.C. Pressure)
20
FIREPLACE INSTALLATION
Connecting Fireplace To Gas Supply
Checking Gas Connections
FIREPLACE INSTALLATION
Continued
CONNECTING FIREPLACE TO GAS SUPPLY
4.
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower louver door panel by gently pulling forward.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to fireplace. Route flexible gas supply line through
one of the access holes on side of fireplace.
3. Attach flexible gas line from gas supply to control valve (see
Figure 32).
4. Check all gas connections for leaks. See Checking Gas
Connections.
Equipment
Shutoff Valve
Flexible Gas Line
Do NOT Kink
Red Surface Indicates
For Propane/LP Use Only
5.
Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a
leak. Correct all leaks at once.
Reconnect fireplace and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
Close equipment shutoff valve (see Figure 33).
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace, or using compressed air.
Check all joints from propane/LP supply tank or gas meter to
equipment shutoff valve (see Figure 34 for propane/LP or Figure
35 for natural gas). Apply noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak. Correct all leaks at once.
Equipment
Shutoff
Valve
1/2" NPT Incoming
Gas Line
Inlet Pressure Tap
Open
Outlet Pressure Tap
Note: Wire Connections Not Shown for Clarity
Closed
Figure 33 - Equipment Shutoff Valve
Figure 32 - Connecting Flexible Gas Line to Electronic Valve
CHECKING GAS CONNECTIONS
Propane/LP
Supply Tank
Equipment
Shutoff
Valve
WARNING: Test all gas piping and connections
for leaks after installing or servicing. Correct all leaks
at once.
WARNING: Never use an open flame to check for a
leak. Apply noncorrosive leak detection fluid to all joints.
Bubbles forming show a leak. Correct all leaks at once.
Gas Valve
Figure 34 - Checking Gas Joints for Propane/LP Gas Fireplace
Equipment
Shutoff
Valve
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
2.
3.
Disconnect fireplace and its individual equipment shutoff valve
from gas supply piping system. Pressures in excess of 1/2 psig
(3.5 kPa) will damage fireplace gas regulator.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace, or using compressed air.
Gas
Meter
Gas Valve
Figure 35 - Checking Gas Joints for Natural Gas Fireplace
For more information, visit www.desatech.com
108862-01D
FIREPLACE INSTALLATION
Checking Gas Connections (Cont.)
Removing/Replacing Glass Door
21
21
FIREPLACE INSTALLATION
Continued
Pressure Testing Fireplace Gas Connections
Removing Glass Door
1.
2.
If replacement of glass is necessary, the entire assembly, glass and
frame, must be replaced. If glass is broken, wear gloves and tape the
remaining fragments onto the frame.
1. Remove screen assembly by pushing the rod either left or right
and then down and forward to remove screen/rod assembly
from the firebox. Set assembly aside.
2. Lift up on latches to unlock. There are two on top of firebox and
two below firebox that hold glass door in place (see Figure 37).
3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on
the left side of door frame assembly (see Figure 37).
4. Remount the new frame at the hinge with five new screws
before closing door. This will ensure seating of the gasket.
5. Close glass door frame. Lock latches by placing the bar under the
tab on door and pushing down and back on latch (see Figure 37).
6. Replace screen/rod assembly by reversing step 1.
7. Replace louvers by reversing procedure under Removing Louver Panels.
3.
4.
5.
6.
Open equipment shutoff valve (see Figure 33, page 20).
Open propane/LP supply tank valve for propane/LP fireplace
or main gas valve located on or near gas meter for natural
gas fireplace.
Make sure control knob of fireplace is in the OFF position.
Check all joints from equipment shutoff valve to gas valve
(see Figure 34 for propane/LP or Figure 35 for natural gas,
page 20). Apply noncorrosive leak detection fluid to all joints.
Bubbles forming show a leak. Correct all leaks at once.
Light fireplace (see Operating Fireplace, pages 25 and 26).
Check all other internal joints for leaks.
Turn off fireplace (see To Turn Off Gas to Appliance, page 25).
REMOVING/REPLACING GLASS DOOR
CAUTION: Do not operate this fireplace with a
broken glass door panel or without the glass door
panel securely in place. For replacement part information see Replacement Parts, page 30.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
Latch
Unlock
Lock
Hinge
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before removing
glass door or louvers.
Screw
Removing Louver Panels
Remove the top and bottom louver panels by simultaneously pulling
both top end spring latches towards the center of the appliance until
they are disengaged from the locating holes (see Figure 36). Repeat
for bottom spring latches and pull the louvers outward. To install or
replace items removed, simply reverse the procedures above.
Glass
Frame
Assembly
Figure 37 - Removing/Replacing Glass Door
Cleaning Glass Door
See Cleaning and Maintenance on page 27.
Spring Latch
Louver Panel
Figure 36 - Removing Louver Panel
For more information, visit www.desatech.com
108862-01D
22
FIREPLACE INSTALLATION
Installing Optional Brick Liner Models BL36D(S), BL36DH(S), BL42D(S), BL42DH(S)
FIREPLACE INSTALLATION
Continued
INSTALLING OPTIONAL BRICK LINER
MODELS BL36D(S), BL36DH(S), BL42D(S),
BL42DH(S)
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before installing
brick liner.
9.
Install logs, lava rock and glowing embers. See Installing Logs,
Lava Rock and Glowing Embers, pages 22 and 23.
10. Close glass door and lock latches on top and bottom of door
and replace screen. See Removing/Replacing Glass Door, steps
5 and 6, page 21.
11. Close top and bottom louvers.
This brick liner kit is optional. You may purchase brick liner from
your local retailer or see Accessories, page 31.
CAUTION: Always handle brick panels with two
hands. Do not force brick panels into place. Excessive force will break brick panels.
1.
2.
3.
4.
5.
6.
7.
8.
Remove top and bottom louvers to allow access to door latches.
Remove screen, unlock door latches and open glass door. See
Removing/Replacing Glass Door, steps 1 and 2, page 21.
If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs,
lava rock, and ember material.
Remove three screws from deflector shield on the inside top
of firebox. Set shield and screws aside.
Install rear brick panel first. Rest bottom edge of panel on back
edge of grate (see Figure 38).
Install top brick panel by resting on the top of the rear panel.
Hold the top brick panel in place and install left side brick
panel by sliding it between the grate and the side of the firebox, securing top panel (see Figure 39).
Install the right brick panel using the same method described
in step 6 for left brick panel.
Replace deflector shield using screws removed in step 4.
Top Brick
Panel
Left Side
Brick Panel
Figure 39 - Installing Left Side and Top Brick Panels
INSTALLING LOGS, LAVA ROCK AND
GLOWING EMBERS
Each log is marked with a number. These numbers will help you
identify the log when installing. It is very important to install these
logs exactly as instructed. Do not modify logs. Only use logs
supplied with fireplace.
Open louvers, remove screen, unlock door latches, and open glass
door. See Removing/Replacing Glass Door, steps 1 and 2, page 21.
Install logs according to instructions for fireplace model numbers.
1. Place log #1 (base log) onto pin on left front side of grate as
shown in Figure 40.
Rear Brick Panel
11
Figure 38 - Installing Rear Brick Panel
Figure 40 - Installing Log No. 1
For more information, visit www.desatech.com
108862-01D
FIREPLACE INSTALLATION
Installing Logs, Lava Rock, and Glowing Embers
23
23
FIREPLACE INSTALLATION
Continued
2.
3.
4.
5.
6.
7.
8.
Rest left side of log #2 (front log) onto top of log #1. Place
right side of log onto second pin located on right side of grate
(see Figure 41).
Place log #3 (rear log) onto pins on rear of grate as shown in
Figure 42.
Place log #4 (crossover log) onto pins from both logs #2 and
#3 as shown in Figure 43.
Place log #5 (top log) onto right pin of front log (#2) and the
smooth surface of crossover log (#4) as shown in Figure 44.
Make sure it is seated properly.
Place log #6 (left log) onto left pin of front log (#2) and the
smooth surface of rear log (#3) as shown in Figure 45. Make
sure it is seated properly.
For (V)V42 series only, place log #7 onto right pin of top log
(#5) as shown in Figure 45. Make sure it is seated properly
Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the
lava rock provided.
9.
Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between
the burner and grate prongs (see Figure 46). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember
material provided.
10. Close glass door, lock door latches, replace screen, and close
louvers (see Removing/Replacing Glass Door, steps 5 through
7, page 21).
WARNING: The glass door must be securely in
place before running this fireplace. Do not run this
fireplace if glass is missing or broken.
5
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner will cause performance problems.
2
Figure 44 - Installing Log No. 5
6
7
42" Series Only
Figure 41- Installing Log No. 2
3
4
Figure 45 - Installing Log No. 6 (36" and 42" Series) and
Log No. 7 (42" Series Only)
Figure 42 - Installing Log No. 3
Figure 43 - Installing Log No. 4
Ember Material
Figure 46 - Placing Ember Material on Burner
For more information, visit www.desatech.com
108862-01D
24
FIREPLACE INSTALLATION
Wall Switch Installation
Optional Remote Control Installation
WIRING DIAGRAM
FIREPLACE INSTALLATION
Continued
WALL SWITCH INSTALLATION
Fireplace
Receptacle
The installation of a wall switch allows you to activate the gas
control valve and turn the fireplace on and off. The wall switch is
to be connected to the incoming 120 volt regular household wiring
that supplies the electricity to the fireplace. Refer to wiring
diagram below.
Remote Control
Receiver
OPTIONAL REMOTE CONTROL
INSTALLATION (Model WRC)
Note: If using optional wireless hand-held remote control, the wall
switch must be in the ON position to be operational. The remote control
then becomes the switching mechanism for fireplace operation.
1. Open lower louver panel.
2. The WRC model receiver does not require a battery. The receiver can be installed by first plugging the short extension
cord into the fireplace receptacle. Then plug the receiver unit
into the extension cord. Finally plug the ignition module plug
into the receiver unit (see Figure 47).
3. Activate the remote handset battery by removing the insulating tab on the back of the handset (see Figure 48). The battery
is included pre-installed.
4. Once the battery is activated the unit is ready to use.
5. Close lower louver panel.
Extension Cord
Ignition
Module Plug
Figure 47 - Installing the WRC Remote Receiver
Battery Cover
12 Volt Battery
Back of
Handset
Pull to Remove
Insulation Tab
Figure 48 - Installing Battery into Back of Handset
WIRING DIAGRAM
Pilot
Burner
Pilot Gas
Line
OFF
WALL SWITCH
(SUPPLIED)
ON
INCOMING MAIN
GAS SUPPLY
BLACK
MV
WHITE
TR GND
PV
BLACK
WHITE
GREEN
PV/MV
Robertshaw
MODEL SP745 IGNITION CONTROL
TH
EV1
GREEN
INCOMING
120V AC
(FUSE BOX
OR BREAKER)
IGN
ELECTRICAL RATING:
120v, 60Hz, 0.7A
EV2
24V AC
STEP DOWN
TRANSFORMER
120V AC
GAS LINE TO
BURNER
OPTIONAL
REMOTE
CONTROL
For more information, visit www.desatech.com
108862-01D
OPERATING FIREPLACE
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Optional Remote Operation
25
25
OPERATING FIREPLACE
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot
by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange
flame will also be present. Open damper or window to
vent smell. This will only last a few hours.
1.
2.
3.
4.
5.
STOP! Read the safety information, above.
Turn off all electric power to the appliance.
Turn wall switch to the OFF position.
Open lower louver panel.
Turn equipment shutoff valve clockwise Clockwise to the OFF
position (see Figure 49). Do not force.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don’t smell
gas, go to the next step.
7. Turn equipment shutoff valve counterclockwise C-clockwise
to the ON position. Do not force.
8. Close lower louver panel.
9. Turn on all electric power to the appliance.
10. Turn the wall switch to the ON position.
11. Visually locate the pilot. The ignitor should begin to spark and
the main burner should ignite once flame appears at pilot.
• If lighting the appliance for the first time each season, it
may take several attempts before the supply gas can reach
the pilot and main burners.
• If the appliance will not stay lit after several attempts,
follow the instructions To Turn Off Gas To Appliance,
below, and call your service technician or gas supplier.
Figure 49 - Turning Equipment Shutoff Valve to the OFF Position
TO TURN OFF GAS
TO APPLIANCE
1.
2.
3.
4.
5.
6.
Turn off the wall switch.
Turn off all electric power to the appliance if service is to
be performed.
Open lower louver panel.
Remove front hearth brick and control access panel.
Turn equipment shutoff valve clockwise Clockwise to OFF.
Do not force.
Close lower louver panel.
Sensing Rod
Pilot Burner
Ignitor
Figure 50 - Pilot
OPTIONAL REMOTE
OPERATION
Note: The WRC receiver and hand-held remote control kit
must be purchased separately (see Accessories, page 31). Follow
installation instructions on page 24.
1. Turn equipment shutoff valve to ON position. You can now turn
the burner on and off with the hand-held remote control unit.
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
2. Press the ON/OFF button to turn the burner on and off.
For more information, visit www.desatech.com
108862-01D
Adjustment
Screw
Equipment Shutoff Valve
OPERATING FIREPLACE
26
Operating Optional Blower Accessory
INSPECTING BURNERS
Pilot Assembly
Burner Flame Pattern
OPERATING FIREPLACE
INSPECTING BURNERS
Continued
Check pilot flame pattern and burner flame patterns often.
OPERATING OPTIONAL
BLOWER ACCESSORY
Locate the blower controls by opening the lower louver panel on
the fireplace. Blower controls are located on the left side of the
switch bracket to the left just inside the louver panel.
The BK manual blower and the BKT thermostatically-controlled blower have an ON setting and an OFF setting. The
blower will only run when the switch is in the ON position. In the
OFF position, the blower will not operate.
Note for BKT Only: If you are using BKT blower with optional
thermostat (wall mounted or remote control) for the fireplace,
your fireplace and blower will not turn on and off at the same
time. The fireplace may run for several minutes before the
blower turns on. After the heater modulates to the pilot position,
the blower will continue to run. The blower will shut off after the
firebox temperature decreases.
PILOT ASSEMBLY
The pilot assembly is factory preset for the proper flame. Alterations
may have occurred during shipping and handling. The pilot is
located on the back right hand side of the burner.
The flame must envelope 1/4" of top of the ignitor/sensor and
grounding stem.
If your pilot assembly does not meet these requirements:
• Turn the adjustment screw marked PILOT clockwise to decrease
or counterclockwise to increase the flame to proper size (see
Figure 49, page 25). Do not remove the adjustment screw.
• see Troubleshooting, pages 28 and 29
Sensing Rod
Pilot Burner
Ignitor/Sensor
The blower helps distribute heated air from the fireplace.
Periodically check the louvers of the firebox and remove any
dust, dirt, or other obstructions that will hinder the flow of air.
Figure 51 - Correct Pilot Flame Pattern
BURNER FLAME PATTERN
Burner flames will be steady; not lifting or floating. Flame patterns
will be different from unit to unit and will vary depending on
installation type and weather conditions.
If the vent configuration is installed incorrectly, the flames will lift
or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.
Figure 52 shows a typical flame pattern for (V)V36E and (V)V42E
series models.
If burner flame pattern differs from that described:
• turn fireplace off (see To Turn Off Gas to Appliance, page 25)
• see Troubleshooting, pages 28 and 29
Figure 52 - Typical Flame Pattern for (V)V36E and (V)V42E Series
Models
For more information, visit www.desatech.com
108862-01D
CLEANING AND MAINTENANCE
Glass Door
Pilot and Burners
Logs
Venting System
27
27
CLEANING AND
MAINTENANCE
WARNING: Turn off fireplace and let cool before
cleaning.
CAUTION: You must keep control areas, burners,
and circulating air passageways of fireplace clean.
Inspect these areas of fireplace before each use.
Have fireplace inspected yearly by a qualified service
person. Fireplace may need more frequent cleaning
due to excessive lint from carpeting, bedding material, pet hair, etc.
GLASS DOOR
WARNING: Handle glass door panel with care. Do
not strike, slam, or otherwise abuse glass. Do not
operate fireplace with the glass door removed,
cracked, or broken.
WARNING: Do not use abrasive cleaners as this
may damage glass. Use a nonabrasive household glass
cleaner to clean glass. Do not clean glass when hot.
Glass must be cleaned periodically. During start-up it is normal for
condensation to form on the inside of the glass causing lint, dust, and
other airborne particles to cling to the glass surface. During initial
start-up a slight film may form on the glass due to paint curing. The
glass should be cleaned several times with a non-ammonia, nonabrasive household cleaner and warm water after the first two weeks
of operation. Thereafter, clean the glass two or three times during
each heating season, depending on the usage and circumstances
present. Refer to Removing/Replacing Glass Door on page 21 of this
manual when removing glass door for cleaning.
WARNING: Only parts supplied by the manufacturer should be used when replacing broken or damaged glass door panel (see Replacement Parts, page
30). This glass door panel is a complete unit. No
substitute materials may be used.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, page 21). Vacuum all glass pieces with
a shop vac.
CAUTION: Do not vacuum if pieces are hot.
Use only the tempered glass door replacement intended for this
fireplace (see Replacement Parts, page 30 for detail on ordering).
No substitutions may be made. See Removing/Replacing Glass
Door, page 21 for instructions for replacing glass door.
WARNING: Do not operate fireplace with the glass
door removed, cracked, or broken.
PILOT AND BURNERS
• Remove ember material before cleaning burners and replace
when cleaning is complete.
• Burner and controls should be cleaned with compressed air to
remove dust, dirt, or lint.
• Use a vacuum cleaner or small, soft bristled brush to remove
excess dust, dirt, or lint.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, Lava
Rock, and Glowing Embers, pages 22 and 23, to properly replace logs.
• Use a vacuum cleaner to remove any carbon buildup on logs.
• Replace log(s) if broken. See Replacement Parts on page 30.
• Replace ember material periodically as needed. See Replacement Parts on page 30.
VENTING SYSTEM
Conduct annual inspection of the venting system following these
guidelines:
1. Check areas of venting system that are exposed to the weather
for corrosion (rust spots or streaks and, in extreme cases, holes).
Have these items replaced immediately by a qualified service
person.
2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.
3. Check for evidence of excessive condensation. Continuous
condensation can cause corrosion of caps, pipes, and fittings
and can be caused by having excessive lateral runs, too many
elbows, or exterior portions of the system being exposed to
cold weather.
4. Inspect joints to verify that no pipe section or fitting has been
disturbed and loosened. Check mechanical supports such as
wall straps for rigidity.
For more information, visit www.desatech.com
108862-01D
28
TROUBLESHOOTING
TROUBLESHOOTING
Note: For additional help, visit DESA
International’s technical service web site
at www.desatech.com.
Note: Before troubleshooting the system,
make sure the gas shutoff valve is ON.
WARNING: Turn off heater
and let cool before servicing. Only
a qualified service person should
service and repair heater.
CAUTION: Never use a wire,
needle, or similar object to
clean pilot. This can damage
pilot unit.
The two most common causes of a malfunctioning gas appliance are:
1. Loose wiring connections
2. Construction debris clogging the pilot and/or gas control valve filter
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Ignitor will not spark or pilot will not light
1. No gas supply, or shutoff valve is OFF
1. Check to see if you have gas supply and
that equipment shutoff valve is opened
2. Repeat lighting procedure several times
to purge all air out of lines. If after repeated attempts appliance does not light,
call for qualified service and repair.
3. Remove debris and dirt, inspect and
clean any other possible obstructions
4. Contact your gas supplier to check
pressure
5. Have a qualified technician replace pilot line
6. Replace control valve (Refer to Replacement Parts, page 30)
7. Check that main power is on and that all
wire connections are made correctly to
the ignition model (see Wiring Diagram,
page 24). Check for 24 VAC at the secondary side of the transformer. If 24
VAC is present, and the module does not
oporate, have the module replaced otherwise have the transformer replaced.
8. Open vent damper until fully locked in
OPEN position
2. Air in gas line
3. Construction debris clogging pilot orifice
4. Low gas pressure
5. Kinked pilot line
6. Control valve knob is not opening
7. No power to unit or the ignition module
or power transformer is bad
8. Vent damper not fully open
Pilot will not stay lit
1. Loose wiring on ignitor wire to ignition
module and/or poor ground to ignition
module
2. Pilot flame too low to sense
1. Check wiring connection. Refer to wiring diagram (see Wiring Diagram, page
24) and/or check ground wire to ignition module
2. Clean and adjust pilot burner and check
gas supply and inlet pressure to unit
Note: Have a qualified technician replace
pilot assembly if broken or corroded
No gas to burner, although wall switch and
valve are set to the ON position
1. Wall switch wires defective or too long
1. Check electrical connections
Frequent pilot outage
1. Pilot flame may be too low, causing
safety pilot to “drop out”
2. Improper venting or excessive blockage
1. Clean and adjust pilot flame for maximum
flame impingement on thermopile
2. Have the vent system inspected, including the termination cap. Remove any
restriction or obstruction
For more information, visit www.desatech.com
108862-01D
TROUBLESHOOTING
29
29
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Fireplace produces a clicking/ticking noise
just after burner is lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common with most fireplaces. If
noise is excessive, contact qualified service person
Slight smoke or odor during initial operation
1. Residues from manufacturing processes
and logs curing
1. Problem will stop after a few hours of
operation
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement at
top of page
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, pages 20 and 21)
2. Replace control valve
Gas odor during combustion
1. Foreign matter between control valve
and burner
2. Gas leak. See Warning statement at
top of page
1. Take apart gas tubing and remove foreign matter
2. Locate and correct all leaks (see Checking Gas Connections, pages 20 and 21)
Glass soots
1. Flame impingement on logs
1. Adjust the log set so that the flame does
not excessively impinge on it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
2. Debris around burner air mixer
Dark residue on logs or inside of fireplace
1. Improper log placement
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
4. Improper venting or excessive blockage
5. Excessive amounts of embers and pan
material
1. Properly locate logs (see log placement
sections on pages 22 and 23)
2. Clean out air holes at burner inlets. Periodically repeat as needed
3. Remove blockage
4. Have the vent system inspected, including the termination cap. Remove any
restrictions or obstruction
5. Clear excess embers until a minimum
gap of 1/2" remains under the grate
For more information, visit www.desatech.com
108862-01D
30
REPLACEMENT PARTS
SPECIFICATIONS
SERVICE HINTS
TECHNICAL SERVICE
REPLACEMENT PARTS
SERVICE HINTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
When Gas Pressure Is Too Low
PARTS UNDER WARRANTY
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESA International’s Customer
Service Department at 1-866-672-6040.
When calling DESA International, have ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
•
•
•
•
pilot will not stay lit
burners will have delayed ignition
fireplace will not produce specified heat
propane/LP gas supply might be low (propane/LP units only)
You may feel your gas pressure is too low. If so, contact your local
gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. If so, contact DESA International’s Customer
Service Department at 1-866-672-6040. When calling, please have
your model and serial numbers of your heater ready.
You can also visit DESA International’s technical service web site
at www.desatech.com.
Contact authorized retailers of this product. If they can not
supply original replacement part(s), call DESA International at
1-866-672-6040 for referral information.
When calling DESA International, have ready
• model number of your fireplace
• the replacement part number
SPECIFICATIONS
(V)V36EN Series
(V)V42EN Series
(V)V36EP Series
(V)V42EP Series
22,000/31,000 Btu/hr
25,000/35,000 Btu/hr
21,000/30,000 Btu/hr
23,000/33,000 Btu/hr
Natural
Natural
Propane/LP
Propane/LP
Ignition
Electronic
Electronic
Electronic
Electronic
Manifold Pressure
3.5" w.c.
3.5" w.c.
10.0" w.c.
10.0" w.c.
Minimum Inlet Supply Pressure
5.5" w.c.
5.5" w.c.
11.0" w.c.
11.0" w.c.
Btu
Gas Type
Dimension, Inches/mm (HxWxD)
Fireplace (Actual size of
firebox. Measurements do not
36" x 41" x 21 1/8"
40" x 48" x 23 1/2"
36" x 41" x 21 1/8"
40" x 48" x 23 1/2"
include nailing flanges or
914 x 1041 x 537 mm 1016 x 1219 x 599 mm 914 x 1041 x 537 mm 1016 x 1219 x 599 mm
standoffs).
Carton
Weight, lbs/kg*
Fireplace
Shipping
38" x 44" x 22"
41" x 51" x 24"
38" x 44" x 22"
41" x 51" x 24"
965 x 1118 x 559 mm 1041 x 1295 x 610 mm 965 x 1118 x 559 mm 1041 x 1295 x 610 mm
120 lbs/55 kg
123 lbs/56 kg
145 lbs/55 kg
148 lbs/56 kg
120 lbs/55 kg
123 lbs/56 kg
145 lbs/55 kg
148 lbs/56 kg
*For refractory lined models add 60 pounds for 36" models and 70 pounds for 42" models.
For more information, visit www.desatech.com
108862-01D
ACCESSORIES
ACCESSORIES
Notice: All accessories may not be available for all
fireplace models.
Purchase these fireplace accessories from your local retailer. If they
can not supply these accessories, call DESA International’s Sales
Department at 1-866-672-6040. for information. You can also write
to the address listed on the back page of this manual.
BRICK LINER
LOUVER TRIM KIT (Rolled Louvers Only)
(Not Shown)
LT36B - 36" Rolled Louver Trim Kit - Brushed Brass
LT36P - 36" Rolled Louver Trim Kit - Platinum
LT36PB - 36" Rolled Louver Trim Kit - Polished Brass
LT42B - 42" Rolled Louver Trim Kit - Brushed Brass
LT42P - 42" Rolled Louver Trim Kit - Platinum
LT42PB - 42" Rolled Louver Trim Kit - Polished Brass
(Not Shown)
DEFLECTION HOODS
BL36D - 36" Textured Refractory Brick Liner Kit
BL36DS - 36" Standard Refractory Brick Liner Kit
BL36DH - 36" Textured Refractory Herringbone Brick Liner Kit
BL36DHS - 36" Standard Refractory Herringbone Brick Liner Kit
BL42D - 42" Textured Refractory Brick Liner Kit
BL42DS - 42" Standard Refractory Brick Liner Kit
BL42DH - 42" Textured Refractory Herringbone Brick Liner Kit
BL42DHS - 42" Standard Refractory Herringbone Brick Liner Kit
(Not Shown)
HD36 - 36" Hood - Black (2" Brow)
HD42 - 42" Hood - Black (2" Brow)
PERIMETER TRIM KIT
(Not Shown)
For all models.
PT36 - 36" Perimeter Trim Kit - Black
PT36B - 36" Perimeter Trim Kit - Brushed Brass
PT36P - 36" Perimeter Trim Kit - Platinum
PT36PB - 36" Perimeter Trim Kit - Polished Brass
PT42 - 42" Perimeter Trim Kit - Black
PT42B - 42" Perimeter Trim Kit - Brushed Brass
PT42P - 42" Perimeter Trim Kit - Platinum
PT42PB - 42" Perimeter Trim Kit - Polished Brass
PROPANE/NATURAL GAS CONVERSION KIT
MANUAL BLOWER KIT - BK
(Not Shown)
Manual variable control blower accessory
provides better heat distribution. Complete
installation and operation instructions included in this manual.
This brick liner adds a touch of style to your direct-vent fireplace.
Complete installation and operation instructions included in this manual.
FLEXIBLE GAS LINE CONNECTOR - GA5081
(Not Shown)
PCDE-36V - Propane/LP Gas Conversion Kit for 36" Victorian
Direct-Vent Electronic Fireplace
PCDE-42V - Propane/LP Gas Conversion Kit for 42" Victorian
Direct-Vent Electronic Fireplace
NCDE-36V - Natural Gas Conversion Kit for 36" Victorian DirectVent Electronic Fireplace
NCDE-42V - Natural Gas Conversion Kit for 42" Victorian DirectVent Electronic Fireplace
FACE/LOUVER PANEL KIT
(Not Shown)
RLD36 - 36" Rolled Louver Panels - Black
FPD36 - 36" Filligree Panel Kit - Black
FPD36B - 36" Filligree Panel Kit - Brushed Brass
FPD36P - 36" Filligree Panel Kit - Platinum
FPD36PB - 36" Filligree Panel Kit - Polished Brass
RLD42 - 42" Rolled Louver Panels - Black
FPD42 - 42" Filligree Panel Kit - Black
FPD42B - 42" Filligree Panel Kit - Brushed Brass
FPD42P - 42" Filligree Panel Kit - Platinum
FPD42PB - 42" Filligree Panel Kit - Polished Brass
THERMOSTATICALLYCONTROLLED BLOWER KIT
BKT
Provides better heat distribution. Blower
turns off and on automatically, as needed.
Complete installation and operation instructions included in this manual.
REMOTE CONTROL KIT - WRC SERIES
(Not Shown)
Standard ON/OFF electronic remote control kit.
For more information, visit www.desatech.com
108862-01D
31
31
32
ILLUSTRATED PARTS BREAKDOWN
(V)V36EN, (V)V36ENS, (V)V36ENH, (V)V36EP, (V)V36EPS, (V)V36EPH
ILLUSTRATED PARTS
BREAKDOWN
(V)V36EN, (V)V36ENS, (V)V36ENH
(V)V36EP, (V)V36EPS, (V)V36EPH
23-2
23-1
6
7
8
23-4
1
23-5
23-3
23-6
10
9
11
4
3
21
17
19
15
22
12
20
18
14
13
2
16
16
5
For more information, visit www.desatech.com
108862-01D
PARTS LIST
33
33
(V)V36EN, (V)V36ENS, (V)V36ENH, (V)V36EP, (V)V36EPS, (V)V36EPH
PARTS LIST
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 30 of this manual.
KEY
NO.
(V)V36EN
(V)V36EP
(V)V36ENS
(V)V36EPS
(V)V36ENH
(V)V36EPH
DESCRIPTION
1
2
3
**
**
108010-01
108010-02
108011-01
108011-02
**
**
**
109082-01
___
___
___
___
108076-01
108719-01
12105
11418
14123
21171
24353
24460
108760-03
108760-04
108032-01
109128-01
109129-01
109130-01
109131-01
109132-01
109133-01
**
**
108010-01
108010-02
108011-01
108011-02
**
**
**
109082-01
See Below
See Below
See Below
See Below
108076-01
108719-01
12105
11418
14123
21171
24353
24460
108760-03
108760-04
108032-01
109128-01
109129-01
109130-01
109131-01
109132-01
109133-01
**
**
108010-01
108010-02
108011-01
108011-02
**
**
**
109082-01
See Below
See Below
See Below
See Below
108076-01
108719-01
12105
11418
14123
21171
24353
24460
108760-03
108760-04
108032-01
109128-01
109129-01
109130-01
109131-01
109132-01
109133-01
Firebox Assembly
Face Weldment
Door Assembly (V Models Only)
Door Assembly (VV Models Only)
Top Panel Louver Assy
Bottom Panel Louver Assy
Fireplace Top
Fireplace Top Insulation
Fireplace Surround
Heat Shield
Top Refractory Brick Panel
Left Refractory Brick Panel
Rear Refractory Brick Panel
Right Refractory Brick Panel
Burner Base Gasket
Screen Rod
Screen
Push-On Nut
Strain Relief
Gas Knock-Out Cover
Handy Box Assembly
Gas Conduit Assembly
Burner Assembly (Natural Gas)
Burner Assembly (Propane/LP Gas)
Log Set
Front Log (Log 1)
Rear Log (Log 2)
Crossover Log (Log 3)
Top Log (Log 4)
Left Log (Log 5)
Base Log (Log 6)
25487
27253
55240
25487
27253
55240
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23-1
23-2
23-3
23-4
23-5
23-6
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
25487
27253
55240
Lava Rock/Bag Assy
Notice Label
Vent Label
1
1
1
REFRACTORY BRICK PANELS
V36ENS, V36EPS VV36ENS, VV36EPS V36ENH, V36EPH VV36ENH, VV36EPH
108081-02
108083-02
108080-02
108082-02
108081-01
108083-01
108080-01
108082-01
108175-02
108177-02
108174-02
108176-02
108175-01
108177-01
108174-01
108176-01
DESCRIPTION
QTY
Top Refractory Brick Panel
Left Refractory Brick Panel
Rear Refractory Brick Panel
Right Refractory Brick Panel
1
1
1
1
** Part not available for field replacement.
For more information, visit www.desatech.com
108862-01D
34
ILLUSTRATED PARTS BREAKDOWN
Burner Assembly for Models (V)V36EN, (V)V36ENS, (V)V36ENH, (V)V36EP, (V)V36EPS, (V)V36EPH
ILLUSTRATED PARTS
BREAKDOWN
BURNER ASSEMBLY FOR MODELS
(V)V36EN, (V)V36ENS, (V)V36ENH,
(V)V36EP, (V)V36EPS, AND (V)V36EPH
4
3
2
5
32
33
31
6
1
7
8
31
17
14
9
16
15
19
12
26
18
10
23
28
13
12
27
30
27
21
11
29
20
22
24
25
For more information, visit www.desatech.com
108862-01D
PARTS LIST
Burner Assembly for Models (V)V36EN, (V)V36ENS, (V)V36ENH, (V)V36EP, (V)V36EPS, (V)V36EPH
PARTS LIST
BURNER ASSEMBLY FOR MODELS
(V)V36EN, (V)V36ENS, (V)V36ENH,
(V)V36EP, (V)V36EPS, AND (V)V36EPH
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 30 of this manual.
KEY
NO.
PART
NUMBER
DESCRIPTION
1
2
3
4
5
108075-02
108759-01
11165
108763-01
104506-25
14514
108866-01
108866-02
11102
108755-01
14546
14544
14528
14554
14500
14569
14570
14253
11107
26808
26827
11147
11186
14115
14120
14126
14129
14134
14149
14301
17223
23416
108863-01
11201
109144-01
108761-01
108754-01
Burner Assembly Base
Burner Pan Assembly
Screw #10 x 5/8 MD TR BLK
Tube Burner
Pan Burner Orifice (Natural Gas)
Pan Burner Orifice (Propane/LPGas)
Pilot Assembly (Natural Gas)
Pilot Assembly (Propane/LP Gas)
Screw #8-32 x 3/8 PPH Zinc
Pilot Bracket
Tube Burner Orifice (Natural Gas)
Tube Burner Orifice (Propane/LPGas)
Brass Elbow Fitting
Tubing Assembly
Brass Fitting
Electronic Valve (Natural Gas)
Electronic Valve (Propane/LP Gas)
Flexible Gas Line
Screw #10-32 x 1/4 PPH Zinc
Valve Bracket
Switch Bracket
Screw #10-24 x 1/2 PPH Zinc
Screw #8-32 x 1 Zinc
Spade Tongue Connector
Spade 1/4 Female Connector
16 GA Green Wire (Ground)
Transformer, 24V
18 GA Black Wire
Spade 1/4 Right Angle Connector
Ignition Module SP745
Magnet
Electronic Components Board
24" Supply Connect Plug
Nut #8-32 Hex Zinc
Air Baffle, 36" (Natural Gas Only)
Grate Assembly
Grate Base
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
For more information, visit www.desatech.com
108862-01D
QTY.
1
1
12
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
4
1
1
2
4
1
4
1
1
5
4
1
2
1
1
4
2
1
1
35
35
36
ILLUSTRATED PARTS BREAKDOWN
(V)V42EN, (V)V42ENS, (V)V42ENH, (V)V42EP, (V)V42EPS, (V)V42EPH
ILLUSTRATED PARTS
BREAKDOWN
(V)V42EN, (V)V42ENS, (V)V42ENH
(V)V42EP, (V)V42EPS, (V)V42EPH
23-2
23-6
23-1
6
7
8
23-4
1
23-5
23-3
23-7
10
9
11
4
3
21
17
19
15
22
12
20
18
14
13
2
16
16
5
For more information, visit www.desatech.com
108862-01D
PARTS LIST
37
37
(V)V42EN, (V)V42ENS, (V)V42ENH, (V)V42EP, (V)V42EPS, (V)V42EPH
PARTS LIST
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 30 of this manual.
KEY
NO.
(V)V42EN
(V)V42EP
(V)V42ENS
(V)V42EPS
(V)V42ENH
(V)V42EPH
DESCRIPTION
1
2
3
**
**
108328-01
108328-02
108331-01
108331-02
**
**
**
109082-02
___
___
___
___
**
**
108328-01
108328-02
108331-01
108331-02
**
**
**
109082-02
See Below
See Below
See Below
See Below
108374-01
108455-01
108740-01
11418
14123
21171
24353
24460
108329-03
108329-04
108778-01
109396-01
109397-01
109398-01
109399-01
109400-01
109401-02
109401-01
**
**
108328-01
108328-02
108331-01
108331-02
**
**
**
109082-02
See Below
See Below
See Below
See Below
108374-01
108455-01
108740-01
11418
14123
21171
24353
24460
108329-03
108329-04
108778-01
109396-01
109397-01
109398-01
109399-01
109400-01
109402-02
109401-01
Firebox Assembly
Face Weldment
Door Assembly (V Models Only)
Door Assembly (VV Models Only)
Top Panel Louver Assy
Bottom Panel Louver Assy
Fireplace Top
Fireplace Top Insulation
Fireplace Surround
Heat Shield
Top Refractory Brick Panel
Left Refractory Brick Panel
Rear Refractory Brick Panel
Right Refractory Brick Panel
Burner Base Gasket
Screen Rod
Screen
Push-On Nut
Strain Relief
Gas Knock-Out Cover
Handy Box Assembly
Gas Conduit Assembly
Burner Assembly (Natural Gas)
Burner Assembly (Propane/LP Gas)
Log Set
Front Log (Log 1)
Rear Log (Log 2)
Crossover Log (Log 3)
Top Log (Log 4)
Left Log (Log 5)
Right Log (Log 6)
Base Log (Log 7)
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23-1
23-2
23-3
23-4
23-5
23-6
23-7
108374-01
108455-01
108740-01
11418
14123
21171
24353
24460
108329-03
108329-04
108778-01
109396-01
109397-01
109398-01
109399-01
109400-01
109401-02
109401-01
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
25487
27253
55240
25487
27253
55240
25487
27253
55240
Lava Rock/Bag Assy
Notice Label
Vent Label
1
1
1
REFRACTORY BRICK PANELS
V42ENS, V42EPS VV42ENS, VV42EPS V42ENH, V42EPH VV42ENH, VV42EPH
108352-02
108354-02
108351-02
108353-02
108352-01
108354-01
108351-01
108353-01
108356-02
108358-02
108355-02
108357-02
108356-01
108358-01
108355-01
108357-01
DESCRIPTION
QTY
Top Refractory Brick Panel
Left Refractory Brick Panel
Rear Refractory Brick Panel
Right Refractory Brick Panel
1
1
1
1
For more information, visit www.desatech.com
108862-01D
38
ILLUSTRATED PARTS BREAKDOWN
Burner Assembly for Models (V)V42EN, (V)V42ENS, (V)V42ENH, (V)V42EP, (V)V42EPS, (V)V42EPH
ILLUSTRATED PARTS
BREAKDOWN
BURNER ASSEMBLY FOR MODELS
(V)V42EN, (V)V42ENS, (V)V42ENH,
(V)V42EP, (V)V42EPS, AND (V)V42EPH
4
3
2
5
32
33
34
31
6
1
7
8
31
17
14
9
16
15
19
12
26
18
10
23
28
13
12
27
30
27
21
11
29
20
22
24
25
For more information, visit www.desatech.com
108862-01D
PARTS LIST
Burner Assembly for Models (V)V42EN, (V)V42ENS, (V)V42ENH, (V)V42EP, (V)V42EPS, (V)V42EPH
PARTS LIST
BURNER ASSEMBLY FOR MODELS
(V)V42EN, (V)V42ENS, (V)V42ENH,
(V)V42EP, (V)V42EPS, AND (V)V42EPH
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 30 of this manual.
KEY
NO.
PART
NUMBER
DESCRIPTION
1
2
3
4
5
108373-01
108330-01
11165
108376-01
104506-24
104506-20
108866-01
108866-02
11102
108755-01
104506-25
104506-20
14528
14554
14500
14569
14570
14253
11107
26808
26827
11147
11186
14115
14120
14126
14129
14134
14149
14301
17223
23416
108863-01
11201
109144-02
108761-02
108346-01
11429
Burner Assembly Base
Burner Pan Assembly
Screw #10 x 5/8 MD TR BLK
Tube Burner
Pan Burner Orifice (Natural Gas)
Pan Burner Orifice (Propane/LPGas)
Pilot Assembly (Natural Gas)
Pilot Assembly (Propane/LP Gas)
Screw #8-32 x 3/8 PPH Zinc
Pilot Bracket
Tube Burner Orifice (Natural Gas)
Tube Burner Orifice (Propane/LPGas)
Brass Elbow Fitting
Tubing Assembly
Brass Fitting
Electronic Valve (Natural Gas)
Electronic Valve (Propane/LP Gas)
Flexible Gas Line
Screw #10-32 x 1/4 PPH Zinc
Valve Bracket
Switch Bracket
Screw #10-24 x 1/2 PPH Zinc
Screw #8-32 x 1 Zinc
Spade Tongue Connector
Spade 1/4 Female Connector
16 GA Green Wire (Ground)
Transformer, 24V
18 GA Black Wire
Spade 1/4 Right Angle Connector
Ignition Module SP745
Magnet
Electronic Components Board
24" Supply Connect Plug
Nut #8-32 Hex Zinc
Air Baffle, 42" (Natural Gas Only)
Grate Assembly
Grate Base
Pin
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
For more information, visit www.desatech.com
108862-01D
QTY.
1
1
12
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
4
1
1
2
4
1
4
1
1
5
4
1
2
1
1
4
2
1
1
2
39
39
40
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
LIMITED WARRANTY
DIRECT-VENT FIREPLACE
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase,
provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under
this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating
condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized
retailers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts
voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a
result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and
any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY
IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY
OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
108862 01
NOT A UPC
108862-01
Rev. D
08/02
For more information, visit www.desatech.com
108862-01D
Download PDF

advertising