Desa (V)VC36N Series Indoor Fireplace User Manual

DIRECT-VENT FIREPLACE
TM
OWNER’S OPERATION AND
INSTALLATION MANUAL
For more information, visit www.desatech.com
NATURAL GAS
“TUDOR” MODEL (V)T32N, (V)T36N SERIES, CHDV32NR, CTDV36NR
PROPANE/LP GAS “TUDOR” MODEL (V)T32P, (V)T36P SERIES
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire
department.
WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property
damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer,
service agency, or the gas supplier.
— Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
— This appliance is only for use with
the type of gas indicated on the rating
plate. This appliance is not convertible
for use with other gases, unless a
certified kit is used.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by state or local codes.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
CLEANING AND MAINTENANCE ............................................ 28
PRODUCT IDENTIFICATION ..................................................... 3
TROUBLESHOOTING .............................................................. 29
LOCAL CODES ........................................................................... 3
REPLACEMENT PARTS .......................................................... 32
PRODUCT FEATURES .............................................................. 4
SPECIFICATIONS .................................................................... 32
PRE-INSTALLATION PREPARATION ........................................ 4
SERVICE HINTS ....................................................................... 32
LOCATION OF TERMINATION CAP .......................................... 6
TECHNICAL SERVICE ............................................................. 32
VENTING INSTALLATION INSTRUCTIONS .............................. 7
ACCESSORIES ........................................................................ 33
FIREPLACE INSTALLATION .................................................... 16
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 34
OPERATING FIREPLACE ........................................................ 25
WARRANTY INFORMATION ...................................... Back Cover
INSPECTING BURNERS .......................................................... 27
SAFETY INFORMATION
affected by carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
WARNINGS
WARNING: This product contains and/or generates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate, or service
this fireplace. Improper use of this fireplace can cause
serious injury or death from burns, fire, explosions,
electrical shock, and carbon monoxide poisoning.
WARNING: This product contains chemicals
known to the State of California to cause cancer or
birth defects, or other reproductive harm.
Propane/LP gas and natural gas are both odorless. An odor-making
agent is added to each of these gases. The odor helps you detect a gas
leak. However, the odor added to these gases can fade. Gas may be
present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this fireplace.
WARNING: Any change to this fireplace or its
controls can be dangerous.
1.
2.
DANGER: Carbon monoxide poisoning may lead
to death!
This fireplace must be installed by a qualified (certified or licensed)
service person. It has a sealed gas combustion chamber that uses a
coaxial pipe (pipe within a pipe and having the same center) venting
system. It brings in fresh air for combustion through the outer pipe and
combustion gases are exhausted through the inner pipe. If the glass
door assembly and venting pipe are not properly seated, connected,
and sealed, carbon monoxide leakage (spillage) can occur.
3.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the fireplace may not have been installed
properly. Get fresh air at once! Have fireplace inspected and
serviced by a qualified service person. Some people are more
4.
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
For propane/LP fireplace, do not place propane/LP supply
tank(s) inside any structure. Locate propane/LP supply tank(s)
outdoors. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier's instructions
• if you cannot reach you gas supplier, call the fire department.
Never install the fireplace
• in a recreational vehicle
• in windy or drafty areas where curtains or other combustible
(flammable) objects can make contact with the fireplace front
• in high traffic areas
For more information, visit www.desatech.com
108661-01E
SAFETY INFORMATION
PRODUCT IDENTIFICATION
LOCAL CODES
SAFETY INFORMATION
3
3
PRODUCT IDENTIFICATION
Continued
Upper Louver
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
This fireplace reaches high temperatures. Keep children and
Panel
Flue Collar
adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.
Carefully supervise young children when they are in the room
with fireplace.
Nailing
Do not modify this fireplace under any circumstances. Any Flange
parts removed for servicing must be replaced prior to operating fireplace.
Turn fireplace off and let cool before servicing, installing, or
Log
repairing. Only a qualified service person should install, ser- Glass
Set
vice, or repair this fireplace. Have fireplace inspected annu- Door
Assembly
ally by a qualified service person.
You must keep control compartments, burners, and circulat- Piezo
Lava
ing air passages clean. More frequent cleaning may be needed Ignitor
Rock
due to excessive lint and dust from carpeting, bedding material, etc. Turn off the gas valve and pilot light before cleaning
fireplace.
Have venting system inspected annually by a qualified service Control
person. If needed, have venting system cleaned or repaired. Valve
Grate
See Cleaning and Maintenance, page 28.
Lower
Assembly
Glowing
Keep the area around your fireplace clear of combustible maLouver
Embers
Panel
terials, gasoline, and other flammable vapor and liquids. Do
not run fireplace where these are used or stored. Do not place
Blower Switch
ON/OFF/REMOTE Switch
items such as clothing or decorations on or around fireplace.
(Optional Installation)
(Optional Installation)
Do not use this fireplace to cook food or burn paper or other
Figure 1 - Tudor Direct-Vent Fireplace with Millivolt Ignition
objects.
Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this fireplace. Use only the gas type indicated on fireplace
nameplate.
Install and use fireplace with care. Follow all local codes. In the
This appliance, when installed, must be electrically grounded absence to local codes, use the current National Fuel Gas Code
in accordance with local codes or, in the absence of local codes, ANSI Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Instalwith the National Electrical Code, ANSI/NFPA 70, or the Ca- lation Code (Canada).
nadian Electrical Code, CSA C22.1.
*Available from:
Do not use fireplace if any part has been exposed to or under
American National Standards Institute, Inc.
water. Immediately call a qualified service person to arrange
1430 Broadway
for replacement of the unit.
New York, NY 10018
National Fire Protection Association, Inc.
Do not operate fireplace if any log is broken.
Batterymarch Park
Do not use a blower insert, heat exchanger insert, or other acQuincy, MA 02269
cessory not approved for use with this fireplace.
Do not operate fireplace with glass door removed, cracked, or
broken.
Provide adequate clearances around air openings.
LOCAL CODES
For more information, visit www.desatech.com
108661-01E
4
PRODUCT FEATURES
PRE-INSTALLATION PREPARATION
Location and Space Requirements
PRODUCT FEATURES
These are a few facts that can help you understand and enjoy your
direct-vent fireplace:
• The venting system may be routed to the outside of your home
in several ways. It may vent through the roof (vertical) or it may
vent to an outside/exterior wall (horizontal). The vent pipe installation is very important to allow for proper operation. You
must follow the venting instructions very carefully for either
vertical or horizontal applications.
• This fireplace may be installed in any room of your house provided
all local codes and these installation instructions are followed.
• This fireplace does not require electricity to operate.
• Only the blower requires electricity if installed and if you plan
to install the blower at a later date, do not forget to wire the
outlet at the bottom of the fireplace when framing.
• A piezo ignitor and ceramic electrode create spark to ignite the
pilot light. It does not require any matches, batteries or any other
sources of ignition to light the pilot.
• Each time you turn on your fireplace, you may notice some
amount of condensation on the inside of the fireplace glass. This
is normal and will disappear after 10-20 minutes of operation.
• Your direct-vent gas fireplace system (fireplace and venting) is a
balanced and sealed gas operating unit. It requires approximately
10-20 minutes of operating time before the flame pattern stabilizes.
PRE-INSTALLATION
PREPARATION
• Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against
any exterior surface on the back, sides, or top of your fireplace,
except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be
placed directly against wall or framing material. See framing
details on page 5.
• If you plan on installing a television or entertainment center recessed above your fireplace, it is recommended that you maintain a minimum 18" above top of louver opening.
• When locating termination cap, it is important to observe the
minimum clearances shown in Figure 7, page 6.
• If recessing into a wall, you can avoid extra framing by positioning your fireplace against an already existing framing member.
• Do not recess termination cap into a wall or siding.
• You may paint the termination cap with 450ºF (232ºC) heatresistant paint to coordinate with the exterior finish.
• There must not be any obstruction such as bushes, garden sheds,
fences, decks, or utility buildings within 24" from the front of
the termination cap.
• Do not locate termination cap where excessive snow or ice build
up may occur. Be sure to clear vent termination area after snow
falls to prevent accidental blockage of venting system. When
using snow blowers, do not direct snow towards vent termination area.
LOCATION AND SPACE REQUIREMENTS
Determine the safest and most efficient location for your DESA
International direct-vent fireplace. Make sure that rafters and wall
studs are not in the way of the venting system. Choose a location
where the heat output is not affected by drafts, air conditioning
ducts, windows or doors. Figure 2 shows some common locations.
Be aware of all restrictions and precautions before deciding the
exact location for your fireplace and termination cap.
When deciding the location of your fireplace, follow these rules:
• Do not connect this fireplace venting to a chimney flue serving
a separate solid-fuel burning fireplace or appliance.
• Due to high temperatures, do not locate this fireplace in high traffic areas, windy or drafty areas, or near furniture or draperies.
• Proper clearances must be maintained.
• If your fireplace is to be installed directly on carpeting, vinyl
tile, or any combustible material other than wood, it must be
installed on a metal or wood panel extending the full width and
depth of the fireplace. See Figure 3.
Flush with a wall
Through exterior wall
enclosed in a chase
Corner
installation
Figure 2 - Common Fireplace Locations
RW
D
FW
Fireplace size
D x FW x RW
32"
36"
16 5/8" 34 3/8" 22 1/2"
29"
21 1/8" 41"
Figure 3 - Fireplace Bottom Dimensions
For more information, visit www.desatech.com
108661-01E
PRE-INSTALLATION PREPARATION
Clearances
Framing and Finishing
5
5
PRE-INSTALLATION
PREPARATION
Continued
CLEARANCES
Minimum clearances to combustibles for the fireplace are as follows:
Back, and sides
0"/mm
Perpendicular walls
6" (152mm)
Floor
0"/mm
Ceiling to louver opening 42" (1067mm)
Front
36" (914mm)
Top
0"/mm
Vent
(See venting instructions for
specific venting clearances.)
Combustible material with a maximum thickness of 5/8" may be
flush with the top front of fireplace .
NOTICE: This fireplace is intended for use as supplemental heat. Use this fireplace along with your primary heating system. Do not install this fireplace as
your primary heat source. If you have a central heating system, you may run system’s circulating blower
while using fireplace. This will help circulate the heat
throughout the house. In the event of a power outage,
you can use this fireplace as a heat source.
D
B
C
A
E
F
G
Nailing Tabs
H
A
B
C
D
E
F
G
H
32" Models 36" Models
353/4"
281/2"
15"
135/8"
495/8"
393/8"
91/2"
103/8"
133/4"
97/8"
41"
343/8"
345/8"
411/4"
681/2"
541/8"
Figure 5 - Framing Clearances for Corner Installation
FRAMING AND FINISHING
1
Figure 4 shows typical framing of this fireplace. Figure 5 shows
framing for corner installation. All minimum clearances must be met.
2
3
A
For available accessories for this fireplace, see Accessories on page
37. If you are using a separate combustible mantel piece, refer to
Figure 6 for proper installation height. You can install noncombustible mantels at any height above the fireplace. Note: Noncombustible mantels may discolor!
A
B
C
4
B
Wall
5
C
6
D
E
7
F
32" Models 36" Models
361/8"
323/8"
345/8"
411/4"
19"
231/2"
G
Top of Louver Opening
Ref. Mantel Depth Ref. Mantel from Top
of Louver Opening
A
B
C
Figure 4 - Framing Clearances for Installation Against an Exterior
Wall
1
2
3
4
5
6
7
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
2" (51mm)
A
B
C
D
E
F
G
16" (406mm)
14" (356mm)
12" (305mm)
10" (254mm)
8" (203mm)
6" (152mm)
4" (101mm)
Figure 6 - Clearances for Combustible Mantels
For more information, visit www.desatech.com
108661-01E
6
LOCATION OF TERMINATION CAP
LOCATION OF TERMINATION CAP
N
N
D
H
V
L
E
B
C
Fixed
Closed
F
B
Openable Fixed
Closed
V
Openable
V
I
V
G
B
V
B
B
J
X
V
G
G
M
A
V
K
X
V
A
V TERMINATION CAP
A = clearance above grade, veranda, porch, deck, or balcony
[*12 inches (305mm) minimum]
B = clearance to window or door that may be opened
[12 inches (305mm) minimum]
C = clearance to permanently closed window [minimum 12 inches
(305mm) recommended to prevent condensation on window]
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (610mm) from the
center-line of the terminal [18 inches (457mm) minimum]
E = clearance to unventilated soffit [12 inches (305mm) minimum]
F = clearance to outside corner (see below)
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly within
36 inches (914mm) horizontally from the center-line of the regulator
I =
J =
K =
L =
M=
N =
G GAS METER
RESTRICTED AREA
(TERMINATION PROHIBITED)
clearance to service regulator vent outlet [*72 inches (1829mm)
minimum]
clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other fireplace [*12 inches (305mm)
minimum]
clearance to a mechanical air supply inlet [*72 inches (1829mm)
minimum]
† clearance above paved side-walk or a paved driveway located on
public property [*84 inches (2133mm) minimum]
clearance under veranda, porch, deck [*12 inches (305mm) minimum ‡]
clearance above a roof shall extend a minimum of 24 inches (610mm)
above the highest point when it passes through the roof surface and
any other obstruction within a horizontal distance of 18 inches (457mm)
X AIR SUPPLY INLET
† vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
*
as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.
Note: Local codes or regulations may require different clearances
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Inside Corner
Outside Corner
Recessed Location
D
C
A
C
A = 6" (152mm)
E
V
V
V
B = 6" (152mm)
B
Balcony with No Side Wall
Balcony with Perpendicular Side Wall
H
G
V
V
J
G = 12" (305mm) minimum clearance
Combustible &
Noncombustible
H = 24" (610mm)
J = 20" (508mm)
C = Maximum depth of 48" (1219mm) for
recessed location
D = Minimum width for back wall of
recessed location Combustible - 38" (965mm)
Noncombustible - 24" (610mm)
E = Clearance from corner in
recessed locationCombustible - 6" (152mm)
Noncombustible - 2" (51mm)
Figure 7 - Minimum Clearances for Termination Cap
For more information, visit www.desatech.com
108661-01E
VENTING INSTALLATION INSTRUCTIONS
Installation Precautions
Installation Planning
7
7
VENTING INSTALLATION
INSTRUCTIONS
NOTICE: Read these instructions completely before attempting installation.
These models are tested and approved for use with DESA International (direct-vent) pipe components and terminations.
The venting system must terminate on the outside of the structure and
can not be attached to a chimney or flue system serving a separate
solid fuel or gas burning appliance. A direct-vent appliance must have
its own venting system. DO NOT common vent this appliance.
These models are approved to be vented either horizontally through
an outside wall or vertically through a roof or chase enclosure using
the following guidelines:
• When venting system terminates horizontally on an outside wall,
you must install a standoff if the termination cap is to be installed directly on a combustible finish such as vinyl, wood,
stucco, etc.
• Never run the vent downward as this may cause excessive temperatures which could cause a fire.
• Vent pipe air space clearances to combustibles are 1" on all sides
except on the horizontal sections, which requires 2" clearance
from the top of the pipe. Where the termination cap penetrates a
combustible wall, 1" air space clearance is required.
• Snorkel terminations are required when minimum clearance to grade
cannot be met (see Figure 16 on page 11).
• Have fireplace and selected vent components on hand to help
determine the exact measurements when elbowing or offsetting.
Always use wall firestops when penetrating walls and firestops
when penetrating ceilings or attic spaces.
• Install horizontal venting with a 1/4" rise for every 12" of run
toward the termination.
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
do so could result in serious injury, property damage
or loss of life.
NOTICE: Failure to follow these instructions will void
the warranty.
INSTALLATION PRECAUTIONS
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
• Installation of any damaged venting component
• Unauthorized modification of the venting system (Do not cut
or alter vent components)
• Installation of any component part not manufactured or approved by DESA International
• Installation other than as instructed by these instructions
WARNING: This gas fireplace and vent assembly
must be vented directly to the outside. The venting
system must NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each
direct-vent gas appliance must use a separate vent
system. Do not use common vent systems.
WARNING: Vent pipe air space clearances to combustibles are 1" on all sides except on the horizontal
sections, which require 2" clearances from the top of
the pipe. Where the termination cap penetrates a combustible wall, 1" air space clearance is required.
INSTALLATION PLANNING
There are two basic types of direct-vent installation:
• Horizontal Termination
• Vertical Termination
Horizontal Termination Installation
IMPORTANT: Horizontal square terminations require only inner
portion of wall firestop. Horizontal installations using round termination require exterior portion of wall firestop available only in vent
kit HTK (see Figure 14, page 10).
1. Set the fireplace in its desired location and determine the route
your horizontal venting will take. Do not secure the fireplace
until all venting has been installed. Some installations require
sliding the fireplace in and out of position to make final venting connections. Figures 14 through 18 on pages 10 through
12 show different configurations for venting with horizontal
termination that will help you decide which application best
suits your installation. Check to see if wall studs or roof rafters
are in the path of your desired venting route. If they are, you
may want to adjust the location of the fireplace.
For more information, visit www.desatech.com
108661-01E
8
VENTING INSTALLATION INSTRUCTIONS
Installation Planning
VENTING INSTALLATION
INSTRUCTIONS
Continued
2.
3.
4.
5.
Direct vent pipe sections and components are designed with
special twist-lock connections.
Twist-Lock Procedure: The female ends of the pipes have
locking lugs (indentations). These lugs will slide straight into
matching slots on the male ends of adjacent pipes. Push pipe
sections together and twist one section clockwise approximately
one-quarter turn until the sections are fully locked (see Figure
8). Note: Horizontal runs of vent must be supported every three
feet. Use wall straps for this purpose.
Use a 45° elbow to connect venting system to fireplace flue collar. The elbow is designed to be twist-locked onto the flue collar
as described in step 2. IMPORTANT: Do not attempt to alter the
configuration of the elbow by cutting, twisting, bending, etc.
Assemble the desired combination of pipe and elbows to the
fireplace. If there are long portions of venting run, pre-assembled pipe sections may be installed as subassemblies for
convenience.
Carefully determine the location where the vent pipe assembly
will penetrate the outside wall. The center of the hole should line
up with the center-line of the horizontal vent pipe. Mark the wall
for a 10" x 10" square hole. Cut and frame the square hole in the
exterior wall where the vent will be terminated. If the wall being
penetrated is constructed of noncombustible material, such as
masonry block or concrete, a 7 3/4" hole with zero clearance is
acceptable (see Figure 9).
WARNING: Do not recess vent termination into
any wall. This will cause a fire hazard.
6.
Male
Slots
Female
Locking
Lugs
Figure 8 - Vent Pipe Connections
Vent Opening
Combustible Wall
10"
(254mm)
10" Inside Framing
(254mm)
10"
(254mm)
Vent Opening
Noncombustible Wall
(Framing
Detail)
7 3/4"
(197mm)
Noncombustible Exterior Wall: Position the horizontal vent
cap in the center of the 7 3/4" round hole and attach to the exterior wall with four wood screws provided. Before attaching
the vent cap to exterior wall, run a bead of non-hardening mastic
(pliable sealant) around the outside edges to make a seal between it and the outside wall. Note: The four wood screws
provided should be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of sidings.
Center
of Hole
Figure 9 - Vent Opening Requirements
For more information, visit www.desatech.com
108661-01E
VENTING INSTALLATION INSTRUCTIONS
9
9
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
Combustible Exterior Wall: For vinyl siding, stucco, or wood
exteriors, a siding standoff must be installed between the vent
cap and exterior wall. The siding standoff prevents excessive
heat from damaging the siding materials. Siding material must
be cut to accommodate standoff. Bolt the vent cap to the standoff. Apply non-hardening mastic around outside edge of standoff. Position the standoff/cap assembly in the center of the 10"
square hole and attach to exterior wall with wood screws provided (see Figure 11). The siding standoff must sit flush against
the exterior fascia material.
7. Slide the wall firestop over the vent pipe before connecting
horizontal run to vent cap (see Figure 12).
8. Carefully move fireplace, with vent assembly attached, toward
wall and insert vent pipe into horizontal termination. The pipe
overlap should be a minimum of 11/4".
9. Slide wall firestop against interior wall surface and attach with
screws provided. See Figure 13, page 10 for horizontal termination details.
10. Place fireplace into position and shim with noncombustible material if needed. Nail or screw side flanges to framing to secure
unit in place. IMPORTANT: Make sure fireplace is level before
securing. If fireplace is not level it will not work properly.
Cut Siding Away
to Fit Standoff
Standoff
Wood Screw
Vent Cap
Screws
Apply Mastic
to All Four Sides
Figure 11 - Installing Siding Standoff
Interior Wall
Surface
Wall
Firestop
Apply Mastic to
All Four Sides
Vent Cap
(Horizontal
Termination)
Horizontal
Vent Pipe
Vent Cap
Wood Screw
Screw
Figure 12 - Connecting Vent Cap with Horizontal Vent Pipe
Figure 10 - Installing Horizontal Vent Cap
For more information, visit www.desatech.com
108661-01E
10
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
Minimum Pipe
Overlap 11/4"
Siding Standoff
WARNING: Never run vent downward as this may
cause excessive temperatures which could cause a
fire. Operation of improperly installed and maintained venting system could result in serious injury,
property damage or loss of life.
Screws
Direct Vent
Pipe
GROUND FLOOR INSTALLATION
Recommended Applications:
• Installation using cabinet surrounds
• Through the wall using round or square termination (up to 12"
horizontal pipe)
• NOT FOR CORNER INSTALLATION
Wall
Firestop
Adjustable
45° Elbow
Pipe 12" Max.
Horizontal High
Wind Square
Termination
Maintain 1"
Minimum Air
Space Around
Outer Pipe When
Penetrating a Wall
High Wind
Termination
10" x 10"
Framed
Opening
Apply Mastic to
Outside Edge of
Standoff
Wall Firestop
Square Termination
Exterior Wall
with Vinyl Siding
Figure 13 - Typical Horizontal Termination Cap Mounting with
Additional Siding Standoff Installed
32" Series
36" Series
45° Elbow
Horizontal Termination Configurations
Figures 14 through 18 show different configurations and alternatives
for venting with horizontal termination. Each figure includes a chart
with critical minimum and maximum dimensions which MUST be
met. IMPORTANT: Remember that a horizontal run of venting must
have a 1/4" rise for every 12" of run toward the termination.
Wall
Firestop
Vertical (V) Horizontal (H)
29" min.
17" max.
32" min.
17" max.
Exterior Portion of Wall
Firestop (Round
Termination Only)
Slide Ring
Over Elbow to
Complete
Connection
Round
Termination
Cap
Round Termination
(Kit HTK Shown)
Figure 14 - Horizontal Termination Configuration for Square and
Round Terminations
For more information, visit www.desatech.com
108661-01E
VENTING INSTALLATION INSTRUCTIONS
11
11
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
CORNER AND ALTERNATE INSTALLATION
Recommended Applications:
• Corner ground floor installation
• Ground floor installation where pipe vents horizontally through wall
(over 12" horizontal pipe)
• Basement installation where one foot clearance from ground to
termination is possible
Wall
Firestop
Square
Termination
Not to Exceed
(H) Limits
Vertical (V)
Required
32"
36"
Vertical Pipe
None
*401/2" min. 431/4" min.
1 ft.
511/2" min. 541/4" min.
631/2" min. 661/4" min.
2 ft.
3 ft.
751/2" min. 781/4" min.
4 ft.
871/2" min. 901/4" min.
*Note: Ground Floor Corner Venting
Horizontal (H) (32"/36")
30" max.
48" max.
60" max.
84" max.
20' max.
Not to Exceed
(H) Limits
90° Elbow
Square
Termination
90° Elbow
As Required for (V)
See Chart for Pipe
Section Required
Wall
Firestop
12" Minimum
45°
Elbow
45° Elbow
Figure 15 - Horizontal Termination Configuration for Corner Installation Using One 90° Elbow
SNORKEL TERMINATION INSTALLATION
Recommended Applications:
• Installations requiring a vertical rise on building exterior
• Any installation using snorkel termination to achieve one foot above ground
Snorkel terminations are available for installations requiring a vertical rise on the exterior of the building. If
installing snorkel termination below grade, you must provide proper drainage to prevent water from entering snorkel
termination (see Figure 16). Do not back fill around snorkel termination.
Snorkel
Termination
Snorkel
Termination
90° Elbow
12"
Minimum
45°
Elbow
12"
Minimum
Adequate
Drainage
Figure 16 - Snorkel Termination Configurations for Below Ground Installation
For more information, visit www.desatech.com
108661-01E
Wall
Firestop
Snorkel
Termination
12"
Minimum
12
VENTING INSTALLATION INSTRUCTIONS
Installation Planning (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
HORIZONTAL SYSTEM INSTALLATION USING TWO 90°
ELBOWS
The following configurations show the minimum vertical rise
requirements for a horizontal system using two 90° elbows.
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
6' max.
12' max.
18' max.
20' max.
20' max.
Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
6' max.
12' max.
18' max.
20' max.
20' max.
45° Elbow
Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace
For more information, visit www.desatech.com
108661-01E
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination
13
13
VENTING INSTALLATION
INSTRUCTIONS
Continued
INSTALLATION FOR VERTICAL TERMINATION
Note: Vertical restrictor must be installed in all vertical installations.
1. Determine the route your vertical venting will take. If ceiling
joists, roof rafters, or other framing will obstruct the venting
system, consider an offset (see Figure 19) to avoid cutting load
bearing members. Note: Pay special attention to these installation instructions for required clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, etc. Do not pack air spaces with insulation.
Also note maximum vertical rise of the venting system and
any maximum horizontal offset limitations.
2. Set the fireplace in desired location. Drop a plumb line down
from the ceiling to the position of the fireplace exit flue. Mark
the center point where the vent will penetrate the ceiling. Drill
a small locating hole at this point.
Drop a plumb line from the inside of the roof to the locating
hole in the ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
Roof Flashing
Wall Strap
45° Elbow
Ceiling Firestop
Figure 19 - Offset with Wall Strap and 45° Elbows
2.
Assemble the desired lengths of pipe and elbows necessary to
reach from the fireplace flue up through the firestop. Be sure
all pipe and elbow connections are fully twist-locked (see Figure 8, page 8).
3. Cut a hole in the roof using the locating hole as a center point.
(Cover any exposed open vent pipes before cutting hole in roof.)
The 10"x10" hole must be measured on the horizontal; actual
length may be larger depending on the pitch of the roof. There
must be a 1" clearance from the vent pipe to combustible materials. Frame the opening as shown in Figure 9, page 8.
4. Connect a section of pipe and extend up through the hole.
Note: If an offset is needed to avoid obstructions, you must
support the vent pipe every 3 feet. Use wall straps for this
purpose (see Figure 19). Whenever possible, use 45° elbows
instead of 90° elbows. The 45° elbow offers less restriction to
the flow of the flue gases and intake air.
5. Place the flashing over the pipe section(s) extending through
the roof. Secure the base of the flashing to the roof and framing with roofing nails. Be sure roofing material overlaps the
top edge of the flashing as shown in Figure 19. There must be
a 1" clearance from the vent pipe to combustible materials.
6. Continue to add pipe sections until the height of the vent cap
meets the minimum building code requirements described in
Figure 7 on page 6. Note: You must increase vent height for
steep roof pitches. Nearby trees, adjoining roof lines, steep
pitched roofs, and other similar factors may cause poor draft
or down-drafting in high winds. Increasing the vent height may
solve this problem.
7. Twist-lock the vent cap onto the last section of vent pipe.
Note: If the vent pipe passes through any occupied areas above the first
floor, including storage spaces and closets, you must enclose pipe. You
may frame and sheetrock the enclosure with standard construction
material. Make sure and meet the minimum allowable clearances to
combustibles. Do not fill any of the required air spaces with insulation.
If area above is a room, install
firestop above framed hole.
Flat Ceiling Installation
1.
Cut a 10" square hole in the ceiling using the locating hole as a
center point. The opening should be framed to 10"x10" (254mm
x 254mm) inside dimensions, as shown in Figure 9 on page 8
using framing lumber the same size as the ceiling joists. If the
area above the ceiling is an insulated ceiling or a room, nail
firestop from the top side. This prevents loose insulation from
falling into the required clearance space. Otherwise, install
firestop below the framed hole. The firestop should be installed
with no less than three nails per side (see Figure 20).
Figure 20 - Installing Firestop
For more information, visit www.desatech.com
108661-01E
If area above is not a room, install
firestop below framed hole.
14
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
VENTING INSTALLATION
INSTRUCTIONS
Continued
Vertical Termination Configurations
Venting with One 90° Elbow
Figures 21 through 24 show four different configurations for vertical termination.
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
Vertical (V)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
45° Elbow
Note: Install restrictor
into inner collar of
fireplace as shown.
Note: Install
restrictor into
inner collar of
fireplace as
shown.
Figure 22 - Vertical Venting Configuration Using One 90° Elbow
(Vertical Round High Wind Termination Shown)
Venting with Two 90° Elbows
Figure 21 - Vertical Venting Configuration Using Two 90° Elbows
with Two Horizontal Runs (Vertical Round High Wind Termination
Shown)
Vertical (V1)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
6' max.
12' max.
18' max.
20' max.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Note: Vertical (V1) + Vertical (V2) = 40' max.
Figure 23 - Vertical Venting Configuration Using Two 90° Elbows
(Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
108661-01E
VENTING INSTALLATION INSTRUCTIONS
Installation for Vertical Termination (Cont.)
High Altitude Installation
15
15
VENTING INSTALLATION
INSTRUCTIONS
Continued
HIGH ALTITUDE INSTALLATION
Vertical Venting
V = 40' max.
Your DESA International direct-vent fireplace has been CSA tested
and approved for elevations from 0-2000 feet (USA) and elevations
from 0-4500 feet (Canada) .
When installing this fireplace at an elevation above 2000 feet (in the
USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet above sea level. Check with your local gas company for
proper orifice size identification.
When installing this fireplace at an elevation above 4500 feet (in
Canada), check with local authorities.
Consult your local gas company to help determine the proper orifice
for your location.
For assistance with any high altitude installation contact DESA
International’s Customer Service Department at 1-866-672-6040.
Note: Install restrictor
into inner collar of
fireplace as shown.
45° Elbow
Figure 24 - Vertical Venting Configuration With No Horizontal
Run (Vertical Round High Wind Termination Shown)
For more information, visit www.desatech.com
108661-01E
16
VENTING INSTALLATION INSTRUCTIONS
Parts Lists for Venting Kits and Components
FIREPLACE INSTALLATION
Check Gas Type
Installing Optional Blower Accessories
VENTING INSTALLATION
INSTRUCTIONS
Continued
PARTS LISTS FOR VENTING KITS AND
COMPONENTS
DESA International Venting Accessories
DESA International Pipe & Vent Kits
SC-47
WF-47
RF-47-6
RF-47-12
VR-47
S-47
WS-47
FP-47
Number Description
P47-6
6" Section Coaxial Pipe - Galvanized
P47-12
12" Section Coaxial Pipe - Galvanized
P47-24
24" Section Coaxial Pipe - Galvanized
P47-36
36" Section Coaxial Pipe - Galvanized
P47-48
48" Section Coaxial Pipe - Galvanized
PA47-712 Adjustable 7"-12" Section Coaxial Pipe - Galvanized
VKG-47 Ground Floor Vent Kit - Galvanized
VKB-47
VKR-47
FIREPLACE INSTALLATION
Basement Vent Kit - Galvanized
CHECK GAS TYPE
Snorkel Kit - Galvanized
Use proper gas type for the fireplace unit you are installing. If you
have conflicting gas types, do not install fireplace. See retailer
where you purchased the fireplace for proper fireplace according to
your gas type.
Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall
Firestop, 36" Snorkel Termination, 4' Pipe, 90° Elbow,
and 26 Screws
INSTALLING OPTIONAL BLOWER
ACCESSORIES
Roof Vent Kit - Galvanized
Includes: 45° Elbow, 7"-12" Adjustable Pipe, Flue Restrictor, Vertical High Wind Termination, 2' Pipe, 4' Pipe,
Firestop Plate, Roof Flashing (0/12-6/12), and 26 Screws
VKC-47
Corner Vent Kit - Galvanized
Includes: 45° Elbow, 7"-12" Adjustable Pipe, Horizontal Termination, 6" Pipe, 90° Elbow, Wall Firestop,
and 18 Screws
HTK
Horizontal Round Termination Kit
Includes: Round Termination, Wall Firestop, and 45° Elbow
DESA International Elbows
Number Description
E47-45
E47-90
45° Elbow - Galvanized
90° Elbow - Galvanized
DESA International Terminations
Number Description
HT-47
HTS-47
VT-47
ST-47-14
ST-47-36
Storm Collar - Galvanized
Wall Firestop - Galvanized
Roof Flashing - 0 to 6/12 Pitch - Galvanized
Roof Flashing - 6/12 to 12/12 Pitch - Galvanized
Vertical Restrictor - Galvanized
Combustible Siding Standoff - Galvanized
Wall Strap
Firestop Plate
Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall Firestop,
Horizontal Square Termination, and 16 Screws
Includes: 45° Elbow, 7"-12" Adjustable Pipe, Wall
Firestop, Horizontal Square Termination, 4' Pipe, 90°
Elbow, and 20 Screws
VKS-47
Number Description
Horizontal Round Termination - Galvanized
Horizontal Square Termination - Galvanized
Vertical Round Termination - Galvanized
14" Snorkel Termination - Galvanized
36" Snorkel Termination - Galvanized
NOTICE: If installing blower in an existing fireplace
with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex electrical outlet
installed in the right side of the bottom of the fireplace
base area, be sure that the electrical power to the outlet
is turned off before proceeding with blower installation.
Failure to do this may result in serious injury.
Model BK Installation
Follow all instructions provided in the blower accessory kit.
1. Attach the power cord to the blower motor by firmly pushing the
two female terminals at the end of the power cord onto the two
spade terminals on the blower motor (see Figure 25, page 17).
2. Attach green ground wire from power cord to blower housing using
screw provided (see Figure 25, page 17). Tighten screws securely.
For more information, visit www.desatech.com
108661-01E
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
17
17
FIREPLACE INSTALLATION
Continued
3.
4.
5.
6.
7.
8.
Spade
Terminals
Magnetic
Strips
k
et i c a l B
hW
ff O
k
e c al
n e ti h W B
er G
5
. C 1 1/ 0
. A. 1 1
V
Wiring Diagram Decal
12" in Front of Blower
Figure 27 - Location of Wiring Diagram Decal (Model May Vary
From Illustration)
Model BKT Installation
Note: When installing the BKT thermostatically-controlled blower,
you must first secure the thermal switch bracket to the blower if it
has not already been factory installed.
1. Place the green ground wire with ring terminal between the
bottom hole on the thermal switch bracket and the top ear hole
on the blower assembly. Insert the phillips screw into all three
pieces and tighten securely (see Figure 28, page 18).
2. Connect wire harness and power cord terminals. Connect the
blue jumper wire to the blower motor terminal and the right
side terminal of the thermal switch. Connect the black wire to
the left side of the thermal switch and the white wire to the
other remaining blower motor terminal.
Note: The power cord outer insulation sleeve may have to be
stripped slightly to allow enough wire length to reach and make all
connections. DO NOT trim excessive length away. Just enable
enough to make all connections securely.
Exhaust
Port
Green
Ground Wire
Screw
Figure 25 - Blower Model BK
For more information, visit www.desatech.com
108661-01E
h c el b a
ti w i r a
Sn V
aF
nO
B
Side View
Figure 26 - Attaching Speed Control to Firebox
al
Lower Firebox
Cavity
Control Shaft
Duplex Outlet (Located
underneath firebox floor
against lower right
outside wall)
kc
Blower
Location
Locknut
Control Knob
B
Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Turn blower on and check for operation. Turn blower off
by turning knob fully counterclockwise before continuing.
10. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27).
Blower
Plug-In
al
9.
Speed Control
kc
CAUTION: Never touch the blower wheel while in
operation.
Switch
Bracket
B
ol
w M
re oto
r
Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward. The blower
will fit inside the back opening and be held in position against
the back wall by the magnets (see Figure 25).
Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green
ground wire is tight.
Mount speed control box to switch bracket by placing the plastic
control shaft forward through the opening in the switch bracket
(see Figure 26).
While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it
is tight against front panel. Place control knob provided on shaft.
Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
Plug in blower power cord.
a. If your firebox is installed as a freestanding unit with an
accessory mantel, determine whether the power cord will
exit the left side or the right side of the firebox. Route power
cord through exit hole and plug the power cord into a wall
receptacle near the firebox.
b. If your firebox installation is recessed and/or pre-wired,
plug the power cord into the duplex outlet provided. Refer
to your firebox owner’s manual for instructions on wiring
the duplex outlet.
18
FIREPLACE INSTALLATION
Installing Optional Blower Accessories (Cont.)
FIREPLACE INSTALLATION
Continued
3.
Place the blower against the lower rear wall of the firebox outer
wrapper with the exhaust port directed upward and the thermodisc
positioned up near the fireplace bottom. The thermodisc must be
oriented near the fireplace bottom as shown in Figure 28 in order
to sense temperature and properly operate. The blower will be
held in position against the back wall by the magnets incorporated onto the blower housing (see Figure 28).
4. Be certain that all wire terminals are securely attached to terminals on blower motor and thermal switch, and that the screw
for the thermodisc bracket and green ground wire is tight.
5. Mount the speed control box against the mounting plate provided in the lower fireplace cavity by placing the plastic control
shaft forward through the round hole (see Figure 26, page 17).
6. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until it is tight against mounting plate. Place control knob provided on shaft (see Figure 26, page 17).
7. Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Also double check all wire leads and make sure wire routing is not pinched or in a precarious position. Correct accordingly.
8. Turn on power to duplex outlet if previously turned off per the
warning in column 2, page 16.
9. Plug in blower power cord to duplex outlet.
10. The blower will only run when the speed control knob is in the
ON position and the thermal switch senses temperature after
the fireplace begins to heat up. The blower speed can be adjusted by rotating the control knob. To turn off, turn knob fully
counterclockwise until it clicks off. If the blower is ON and
has been running with the fireplace operating, the blower will
continue to run for a short time after the fireplace has been
turned off. As the thermal switch cools down, the blower shuts
down automatically.
11. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front
of the blower (see Figure 27, page 17).
White Wire
Blue Wire
Power Cord
Thermal
Switch
Bracket
Magnetic
Strips
Air Flow
Direction
Black
Wire
Phillips
Screw
Ring Terminal
on Green Wire
Air Flow Direction
Magnets
Thermal Switch
Route BKT
Blower Through
This Area
Thermodisc
Blower
Location
Side View Firebox Bottom
Figure 28 - Blower Model BKT
Blower Wiring Diagram
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
Variable
Fan Switch
Off
Fan Switch
(N.O.)
1
2
Black
On
Blue
110/115
V.A.C.
Black
White
Green
Blower
Motor
Figure 29 - Blower Wiring Diagram for Thermostat-Controlled
Models
For more information, visit www.desatech.com
108661-01E
FIREPLACE INSTALLATION
Installing Gas Piping to Fireplace Location
19
19
FIREPLACE INSTALLATION
Continued
INSTALLING GAS PIPING TO FIREPLACE
LOCATION
WARNING: A qualified service person must connect fireplace to gas supply. Follow all local codes.
CAUTION: For propane/LP units, never connect
fireplace directly to the propane/LP supply. This
heater requires an external regulator (not supplied).
Install the external regulator between the fireplace
and propane/LP supply.
Installation Items Needed
Before installing fireplace, make sure you have the items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local codes)
* A CSA design-certified equipment shutoff valve with 1/8" NPT tap
is an acceptable alternative to test gauge connection. Purchase the
CSA design-certified equipment shutoff valve from your retailer.
For propane/LP connection only, the installer must supply an
external regulator. The external regulator will reduce incoming gas
pressure. You must reduce incoming gas pressure to between 11 and
14 inches of water. If you do not reduce incoming gas pressure,
fireplace regulator damage could occur. Install external regulator
with the vent pointing down as shown in Figure 30. Pointing the vent
down protects it from freezing rain or sleet.
External
Regulator
Propane/LP
Supply Tank
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to fireplace.
If pipe is too small, undue loss of volume will occur.
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from fireplace (see Figure 31).
IMPORTANT: Install main gas valve (equipment shutoff valve) in
an accessible location. The main gas valve is for turning on or
shutting off the gas to the appliance.
Check your building codes for any special requirements for locating
equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 31. Locate sediment trap/drip leg where it
is within reach for cleaning. Install in piping system between fuel
supply and fireplace. Locate sediment trap/drip leg where trapped
matter is not likely to freeze. A sediment trap traps moisture and
contaminants. This keeps them from going into fireplace gas controls. If sediment trap/drip leg is not installed or is installed wrong,
fireplace may not run properly.
CSA Design-Certified
Equipment Shutoff Valve
with 1/8" NPT Tap*
Approved Flexible
Gas Line
3" Minimum
Vent
Pointing
Down
Cap
Figure 31 - Gas Connection
Figure 30 - External Regulator with Vent Pointing Down
(Propane/LP Only)
Pipe Nipple
Tee Joint
Sediment Trap/Drip Leg
* The CSA design-certified equipment shutoff valve may be supplied with the appliance or you can purchase it from your retailer.
For more information, visit www.desatech.com
108661-01E
Natural - From
Gas Meter (5.5"
W.C. to 10.5"
W.C. Pressure)
Propane/LP
From External
Regulator (11"
W.C. to 14"
W.C. Pressure)
FIREPLACE INSTALLATION
20
Connecting Fireplace To Gas Supply
Checking Gas Connections
FIREPLACE INSTALLATION
Continued
CONNECTING FIREPLACE TO GAS SUPPLY
4.
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower louver door panel by gently pulling forward.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to fireplace. Route flexible gas supply line through
one of the access holes on side of fireplace.
3. Attach flexible gas line from gas supply to control valve (see
Figure 32).
4. Check all gas connections for leaks. See Checking Gas
Connections.
To Gas Supply
(Natural)
To External
Regulator
(Propane/LP)
Equipment
Shutoff Valve
Control
Valve
5.
Check all joints of gas supply piping system. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a
leak. Correct all leaks at once.
Reconnect fireplace and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
Close equipment shutoff valve (see Figure 33).
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace, or using compressed air.
Check all joints from propane/LP supply tank or gas meter to
equipment shutoff valve (see Figure 34 for propane/LP or
Figure 35 for natural gas). Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct
all leaks at once.
Equipment
Shutoff
Valve
Open
Flexible Gas Line
Do NOT Kink
Closed
Figure 33 - Equipment Shutoff Valve
Figure 32 - Attaching Flexible Gas Line to Control Valve
CHECKING GAS CONNECTIONS
Propane/LP
Supply Tank
Equipment
Shutoff
Valve
WARNING: Test all gas piping and connections
for leaks after installing or servicing. Correct all
leaks at once.
WARNING: Never use an open flame to check for
a leak. Apply a noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak. Correct all leaks
at once.
Gas Valve
Figure 34 - Checking Gas Joints for Propane/LP Gas Fireplace
Pressure Testing Gas Supply Piping System
Equipment
Shutoff
Valve
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
2.
3.
Disconnect fireplace and its individual equipment shutoff valve
from gas supply piping system. Pressures in excess of 1/2 psig
(3.5 kPa) will damage fireplace gas regulator.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas fireplace or opening main
gas valve located on or near gas meter for natural gas fireplace,
or using compressed air.
Gas
Meter
Gas Valve
Figure 35 - Checking Gas Joints for Natural Gas Fireplace
For more information, visit www.desatech.com
108661-01E
FIREPLACE INSTALLATION
Checking Gas Connections (Cont.)
Installing Optional Wireless Hand-Held Remote Control - GHRC and GHRCT(A) Series
21
21
FIREPLACE INSTALLATION
Continued
Pressure Testing Fireplace Gas Connections
1.
2.
3.
4.
5.
6.
Open equipment shutoff valve (see Figure 33, page 20).
Open propane/LP supply tank valve for propane/LP fireplace
or main gas valve located on or near gas meter for natural gas
fireplace.
Make sure control knob of fireplace is in the OFF position.
Check all joints from equipment shutoff valve to gas valve (see
Figure 34 for propane/LP or Figure 35 for natural gas, page 20).
Apply noncorrosive leak detection fluid to all joints. Bubbles
forming show a leak. Correct all leaks at once.
Light fireplace (see Operating Fireplace, pages 25 through
27). Check all other internal joints for leaks.
Turn off fireplace (see To Turn Off Gas to Appliance, page 25).
INSTALLING OPTIONAL WIRELESS HANDHELD REMOTE CONTROL - GHRC AND
GHRCT(A) SERIES
To Optional
Remote
Accessory
Figure 37 - Disconnecting TH to
TPTH Wire
Figure 38 - Control Valve
Terminals
Installing 9-Volt Alkaline Battery in Hand-Held
Remote Control Unit
1.
2.
3.
Remove battery cover on back of remote control unit.
Attach terminal wires to a 9-volt alkaline battery (not included).
Place battery into the battery housing.
Replace battery cover onto remote control unit.
Battery Cover
Terminal
Wires
Remote
Control Unit
NOTICE: Use only alkaline batteries (not included).
9-Volt
Alkaline
Battery
Installing Remote Receiver
1.
2.
3.
4.
5.
6.
7.
Open bottom louver and locate the switch bracket on the left.
Unscrew the switch bracket. Lean bracket forward so you are
able to access the back of the remote receiver.
Locate the battery clip mounted on the back of the receiver.
Slide a 9-volt alkaline battery (not included) through the clip
(see Figure 36).
Attach the terminal wires to the battery.
Remove wire from TH to TPTH on control valve (see Figure 37).
Connect wires from receiver to TH and TPTH to control valve
(see Figure 38).
Replace the switch bracket.
Battery
Housing
Figure 39 - Installing Alkaline Battery in Hand-Held Remote
Control Unit ([C]GHRC)
Terminal
Wires
9-Volt
Battery
Receiver
Battery
Cover
9-Volt
Alkaline
Battery
Terminal
Wires
Figure 40 - Installing Battery in Hand-Held Remote Control Unit
([C]GHRCT[A] Series)
Battery Clip
Figure 36 - Attaching Alkaline Battery to Receiver
For more information, visit www.desatech.com
108661-01E
Remote
Control
Unit
22
FIREPLACE INSTALLATION
Removing/Replacing Glass Door
Installing Optional Brick Liner Models BL32D, BL36D(S), BL36DH(S)
FIREPLACE INSTALLATION
Continued
REMOVING/REPLACING GLASS DOOR
CAUTION: Do not operate this fireplace with a
broken glass door panel or without the glass door
panel securely in place. For replacement part information see Replacement Parts, page 36.
6.
7.
Replace screen/rod assembly by reversing step 1.
Replace louvers by reversing procedure under Removing Louver Panels, page 22.
Unlock
Lock
Latch
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before removing
glass door or louvers.
Hinge
Screw
Removing Louver Panels
Remove the top and bottom louver panels by simultaneously pulling
both top end spring latches towards the center of the appliance until
they are disengaged from the locating holes (see Figure 41). Repeat
for bottom spring latches and pull the louvers outward. To install or
replace items removed, simply reverse the procedures above.
Glass
Frame
Assembly
Figure 42 - Removing/Replacing Glass Door
Cleaning Glass Door
See Cleaning and Maintenance on page 28.
Spring Latch
Louver Panel
INSTALLING OPTIONAL BRICK LINER
MODELS BL32D, BL36D(S), BL36DH(S)
Figure 41 - Removing Louver Panel
WARNING: If fireplace has been running, turn
off and unplug fireplace. Let cool before installing
brick liner.
Removing Glass Door
If replacement of glass is necessary, the entire assembly, glass and
frame, must be replaced. If glass is broken, wear gloves and tape the
remaining fragments onto the frame.
1. Remove screen assembly by pushing the rod either left or right
and then down and forward to remove screen/rod assembly
from the firebox. Set assembly aside.
2. Lift up on latches to unlock. There are two on top of firebox and
two below firebox that hold glass door in place (see Figure 42).
3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on
the left side of door frame assembly (see Figure 42).
4. Remount the new frame at the hinge with five new screws
before closing door. This will ensure seating of the gasket.
5. Close glass door frame. Lock latches by placing the bar under the
tab on door and pushing down and back on latch (see Figure 42).
This brick liner kit is optional. You may purchase brick liner from
your local retailer or see Accessories, page 37.
CAUTION: Always handle brick panels with two
hands. Do not force brick panels into place. Excessive force will break brick panels.
1.
2.
3.
Remove top and bottom louvers to allow access to door latches.
Unlock door latches and open glass door. See steps 1 and 2 of
Removing/Replacing Glass Door, page 22.
If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs,
lava rock, and ember material.
For more information, visit www.desatech.com
108661-01E
FIREPLACE INSTALLATION
Installing Optional Brick Liner Models BL32D, BL36D(S), BL36DH(S)
Installing Logs, Lava Rock and Glowing Embers
23
23
FIREPLACE INSTALLATION
Continued
4.
Remove three screws from deflector shield on the inside top
of firebox. Set shield and screws aside.
5. Install rear brick panel first. Rest bottom edge of panel on back
edge of grate (see Figure 43).
6. Install top brick panel (36" Series only) by resting on the top
of the rear panel. Hold the top brick panel in place and install
left side brick panel by sliding it between the grate and the
side of the firebox, securing top panel (see Figure 44).
7. Install the right brick panel using the same method described
8. Replace deflector shield using screws removed in step 4.
9. Follow instructions on page 24 to install logs, lava rock, and
ember material.
10. Close glass door, lock latches on top and bottom of door and
replace screen (see steps 5 and 6 of Removing/Replacing Glass
Door, page 22).
11. Close top and bottom louvers.
INSTALLING LOGS, LAVA ROCK AND
GLOWING EMBERS
Note: 36" models shown. Logs will vary slightly for 32" models.
Each log is marked with a number. These numbers will help you
identify the log when installing. It is very important to install these
logs exactly as instructed. Do not modify logs. Only use logs
supplied with fireplace.
Open louvers, remove screen, unlock door latches, and open glass
door. See steps 1 and 2 of Removing/Replacing Glass Door, page 22.
Install logs according to instructions for fireplace model numbers.
1. Place log #1 (rear log) on top of grate. Make sure the notches
in the bottom of the log fit over the grate (see Figure 45).
2. Rest log #2 (large front log) on the pins on the front part of the grate
(see Figure 46).
1
Rear Brick Panel
Figure 45 - Installing Log No. 1
Figure 43 - Installing Rear Brick Panel
2
Top Brick Panel
((V)T36 Series
and CTDV36NR
Only)
Left Side
Brick Panel
Figure 46 - Installing Log No. 2
Figure 44 - Installing Left Side and Top Brick Panels
For more information, visit www.desatech.com
108661-01E
24
FIREPLACE INSTALLATION
Installing Logs, Lava Rock and Glowing Embers (Cont.)
FIREPLACE INSTALLATION
Continued
3.
4.
5.
6.
7.
Place log #3 (crossover log) onto the rear and front logs. Make
sure it is seated properly on the smooth surface on the front log
and on the pin on the back log as shown in Figure 47.
Place log #4 (right log) on the pin on the right side of front log
as shown in Figure 48.
Place log #5 (base log) onto the front left part of the grate making
sure the notches fit over the prongs of the grate). See Figure 49.
Place log #6 (left log) onto two pins on the left side of back and
front log. See Figure 49.
Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the
lava rock provided.
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner will cause performance problems.
8.
9.
Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between
the burner and grate prongs (see Figure 50). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember
material provided.
Close glass door, lock door latches, replace screen and close
louvers (see steps 5 and 7 of Removing/Replacing Glass Door,
page 22).
WARNING: The glass door must be securely in
place before running this fireplace. Do not run this
fireplace if glass is missing or broken.
4
Figure 48 - Installing Log No. 4
6
5
Figure 49 - Installing Logs No. 5 and No. 6
3
Ember Material
Figure 50 - Placing Ember Material on Burner
Figure 47 - Installing Log No. 3
For more information, visit www.desatech.com
108661-01E
OPERATING FIREPLACE
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Manual Lighting Procedure
25
25
OPERATING FIREPLACE
FOR YOUR SAFETY READ
BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
STOP! Read the safety information above.
Open lower louver panel.
Disconnect the wire that runs from TH to TPTH from the
control valve.
Turn off all electric power to the fireplace.
Push in gas control knob slightly and turn clockwise
to “OFF”.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don't smell
gas, go to the next step.
The pilot is located by the main burner and should not require accessing for lighting.
Turn gas control knob counterclockwise
to “PILOT”.
Push in gas control knob all the way and hold. Immediately light the pilot by repeatedly depressing the piezo spark
ignitor until a flame appears. Continue to hold for about
one (1) minute after the pilot is lit. Release gas control knob
and it will pop back. Pilot should remain lit. If it goes out,
repeat steps 5 through 8.
11.
12.
13.
14.
Variable Control Knob
Gas Control
Knob
Piezo
Ignitor
LOT
PI
LO
Figure 51 - Control Valve
TO TURN OFF GAS
TO APPLIANCE
1.
2.
3.
4.
5.
Open lower louver panel.
Set selector switch in the OFF position to prevent draining
battery.
Turn off all electrical power to the appliance if service is to
be performed.
Push in gas control knob slightly and turn clockwise
to “OFF”.
Close lower louver panel.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
1. Turn gas control knob clockwise
to the PILOT
position.
2. Set selector switch in the OFF position.
MANUAL LIGHTING
PROCEDURE
1.
2.
3.
4.
5.
Remove glass door (see Removing/Replacing Glass Door,
page 22.)
Follow steps 1 through 8 under Lighting Instructions.
Depress gas control knob and light pilot with match.
Keep gas control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release gas control knob. Follow steps 10 through 14 under Lighting Instructions.
Replace glass door (see Removing/Replacing Glass Door,
page 22).
For more information, visit www.desatech.com
108661-01E
IH
ON
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
10.
OFF
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
• If gas control knob does not pop up when released, stop
and immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician
or gas supplier.
Reconnect the wire that runs from TH to TPTH to the
control valve.
Turn on all electric power to the fireplace.
Turn gas control knob counterclockwise
to “ON”.
This valve is equipped with a HI/LO feature. Set fireplace
input as desired.
Close lower louver panel.
26
OPERATING FIREPLACE
Optional Remote Operation
OPERATING FIREPLACE
Continued
Note: All remote control accessories must be purchased separately (see Accessories, page 37). Follow instructions included
with the remote control.
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
GHRCT(A) Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 54). The lights to the left of the button
will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held remote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
Selector Switch in
Remote Position
T
ON
ON
OF
GHRC Series Operation:
OFF
Variable
Control Knob
LO
After lighting, let pilot flame burn for about one minute. Turn
gas control knob to ON position. Adjust variable control knob
anywhere between HI and LO. Slide the selector switch to the
REMOTE position (see Figure 53). Note: The burners may
light if hand-held remote ON button was on when selector
switch was last turned off. You can now turn the burners on
and off with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
ON
OFF
REMOTE
1.
Blower Control Knob
(Optional Accessory)
PILO
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instructions on page 25.
3.
F
(Optional [C]GHRCT[A] Only) The thermostat control setting
on the remote control unit can be set to any comfort level
between HI and LO. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort
setting will vary by household depending upon the amount of
space to be heated, the output of the central heating system, etc.
IMPORTANT: This remote control has been specially
engineered to take an air temperature sample every 5.5
minutes in the auto mode. It will not respond immediately to the temperature setting being turned up or down.
IMPORTANT: The hand-held remote control unit must
be near the heater. Do not keep the hand-held remote
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the fireplace off.
To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position.
HI
OPTIONAL REMOTE
OPERATION
Gas Control Knob
in ON Position
Figure 52 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
Shows
Temperature
Setting
The Log Heater
will Automatically
Cycle between
Pilot and the Heat
Setting that has
been Selected
Increases Room
Temperature in
AUTO Mode
Decreases Room
Temperature in
AUTO Mode
Turns Burners On
or Off and Allows
You to Choose the
Auto Setting
Figure 53 - Thermostat Hand-Held Remote Control Unit Selections
([C]GHRCT[A] Series Only)
For more information, visit www.desatech.com
108661-01E
OPERATING FIREPLACE
Operating Optional GWMT1 Wall Mounted Thermostat
Operating Optional Blower Accessory
27
27
INSPECTING BURNERS
Pilot Assembly
Burner Flame Pattern
OPERATING FIREPLACE
INSPECTING BURNERS
Continued
Check pilot flame pattern and burner flame patterns often.
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
WARNING: Do not connect the thermostat to a
power source. Electrical shock and/or a fire hazard
will occur.
Light the fireplace as instructed in Lighting Instructions on page
25. Set wall thermostat to desired temperature.
This thermostat has been electronically calibrated at the factory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper
operation.
To turn the fireplace off, adjust thermostat to the lowest setting
and turn the gas control knob back to PILOT. The pilot will
remain lit.
PILOT ASSEMBLY
The pilot assembly is factory preset for the proper flame height.
Alterations may have occurred during shipping and handling. Call
a qualified service person to readjust the pilot if necessary.
The height of the thermopile must be 3/8" to 1/2" above the pilot
flame as shown in Figure 55. The thermocouple must be at a height
of about 1/8" above the pilot flame. The flame from the pilot burner
must extend beyond both the thermocouple and thermopile.
If you pilot assembly does not meet these requirements:
• turn fireplace off (see To Turn Off Gas to Appliance, page 25)
• see Troubleshooting, pages 29 through 31
Thermopile
3/8" to 1/2"
Pilot Burner
1/8"
IMPORTANT: To turn the pilot off, turn the gas control knob
on the heater to the OFF position.
OPERATING OPTIONAL
BLOWER ACCESSORY
Thermocouple
Piezo
Ignitor
Locate the blower controls by opening the lower louver panel on
the fireplace. Blower controls are located on the left side of the
switch bracket to the left just inside the louver panel.
Figure 54 - Pilot Assembly
The BK manual blower and the BKT thermostatically-controlled blower have an ON setting and an OFF setting. The
blower will only run when the switch is in the ON position. In the
OFF position, the blower will not operate.
Burner flames will be steady; not lifting or floating. Flame patterns
will be different from unit to unit and will vary depending on
installation type and weather conditions.
Note for BKT Only: If you are using BKT blower with optional
thermostat (wall mounted or remote control) for the fireplace,
your fireplace and blower will not turn on and off at the same
time. The fireplace may run for several minutes before the
blower turns on. After the heater modulates to the pilot position,
the blower will continue to run. The blower will shut off after the
firebox temperature decreases.
The blower helps distribute heated air from the fireplace.
Periodically check the louvers of the firebox and remove any
dust, dirt, or other obstructions that will hinder the flow of air.
BURNER FLAME PATTERN
If the vent configuration is installed incorrectly, the flames will lift
or "ghost". This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.
Figure 56 shows a typical flame pattern for (V)T32 and (V)T36 series
models.
If burner flame pattern differs from that described:
• turn fireplace off (see To Turn Off Gas to Appliance, page 25)
• see Troubleshooting, pages 29 through 31
Figure 55 - Typical Flame Pattern for (V)T32 and (V)T36 Series
Models
For more information, visit www.desatech.com
108661-01E
28
CLEANING AND MAINTENANCE
Glass Door
Pilot and Burners
Logs
Venting System
CLEANING AND
MAINTENANCE
WARNING: Turn off fireplace and let cool before
cleaning.
CAUTION: You must keep control areas, burners,
and circulating air passageways of fireplace clean.
Inspect these areas of fireplace before each use.
Have fireplace inspected yearly by a qualified service
person. Fireplace may need more frequent cleaning
due to excessive lint from carpeting, bedding material, pet hair, etc.
GLASS DOOR
WARNING: Handle glass door panel with care. Do
not strike, slam, or otherwise abuse glass. Do not
operate fireplace with the glass door removed,
cracked, or broken.
WARNING: Do not use abrasive cleaners as this
may damage glass. Use a nonabrasive household glass
cleaner to clean glass. Do not clean glass when hot.
Glass must be cleaned periodically. During start-up it is normal for
condensation to form on the inside of the glass causing lint, dust, and
other airborne particles to cling to the glass surface. During initial
start-up a slight film may form on the glass due to paint curing. The
glass should be cleaned several times with a non-ammonia, nonabrasive household cleaner and warm water after the first two weeks
of operation. Thereafter, clean the glass two or three times during
each heating season, depending on the usage and circumstances
present. Refer to Removing/Replacing Glass Door on page 22 of this
manual when removing glass door for cleaning.
WARNING: Only parts supplied by the manufacturer should be used when replacing broken or damaged glass door panel (see Replacement Parts, page
36). This glass door panel is a complete unit. No
substitute materials may be used.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
CAUTION: Do not vacuum if pieces are hot.
Use only the tempered glass door replacement intended for this
fireplace (see Replacement Parts, page 36 for detail on ordering).
No substitutions may be made. See Removing/Replacing Glass
Door, page 22 for instructions for replacing glass door.
WARNING: Do not operate fireplace with the glass
door removed, cracked, or broken.
PILOT AND BURNERS
• Remove ember material before cleaning burners and replace
when cleaning is complete.
• Burner and controls should be cleaned with compressed air to
remove dust, dirt, or lint.
• Use a vacuum cleaner or small, soft bristled brush to remove
excess dust, dirt, or lint.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, Lava
Rock, and Glowing Embers, page 24, to properly replace logs.
• Use a vacuum cleaner to remove any carbon buildup on logs.
• Replace log(s) if broken. See Replacement Parts on page 36.
• Replace ember material periodically as needed. See Replacement Parts on page 36.
VENTING SYSTEM
Conduct annual inspection of the venting system following these
guidelines:
1. Check areas of venting system that are exposed to the weather
for corrosion (rust spots or streaks and, in extreme cases, holes).
Have these items replaced immediately by a qualified service
person.
2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material.
3. Check for evidence of excessive condensation. Continuous
condensation can cause corrosion of caps, pipes, and fittings
and can be caused by having excessive lateral runs, too many
elbows, or exterior portions of the system being exposed to
cold weather.
4. Inspect joints to verify that no pipe section or fitting has been
disturbed and loosened. Check mechanical supports such as
wall straps for rigidity.
If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, page 22). Vacuum all glass pieces with
a shop vac.
For more information, visit www.desatech.com
108661-01E
TROUBLESHOOTING
29
29
TROUBLESHOOTING
Note: For additional help, visit DESA
International’s technical service web
site at www.desatech.com.
WARNING: Turn off heater and
let cool before servicing. Only a qualified service person should service
and repair heater.
Note: All troubleshooting items are listed in
order of operation.
CAUTION: Never use a wire,
needle, or similar object to
clean pilot. This can damage
pilot unit.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3. Piezo ignitor nut is loose
4.
5.
6.
7.
When ignitor button is pressed, there is
spark at pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Gas control knob not in PILOT position
3. Gas control knob not pressed in while
in PILOT position
4. Air in gas lines when installed
5. Depleted gas supply (propane/LP models
only)
6. Pilot is clogged
7. Gas regulator setting is not correct
Pilot lights but flame goes out when control
knob is released
1. Gas control knob not fully pressed in
2. Gas control knob not pressed in long
enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor. Nut
is located behind the mounting bracket
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace pilot assembly
7. Replace pilot assembly
1. Turn on gas supply or open equipment
shutoff valve
2. Turn gas control knob to PILOT position
3. Press in gas control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is removed
5. Contact local propane/LP gas company
6. Clean pilot (see Cleaning and Maintenance, page 28) or replace pilot assembly
7. Replace gas control
1. Press in gas control knob fully
2. After pilot lights, keep gas control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural or propane/LP
gas company
B) Clean pilot (see Cleaning and
Maintenance, page 28) or replace pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace pilot assembly
7. Replace control valve
For more information, visit www.desatech.com
108661-01E
30
TROUBLESHOOTING
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Contact local propane/LP or natural gas
company
3. Reconnect leads
2. Inlet gas pressure is too low
3. Thermopile leads disconnected or improperly connected
4. Thermopile is defective
Delayed ignition burner
1. Manifold pressure is too low
2. Burner porting or orifice clogged
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
4. Replace thermopile
1. Contact local propane/LP or natural gas
company
2. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Damaged burner
3. Gas regulator defective
1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
2. Replace damaged burner
3. Replace gas control
Slight smoke or odor during initial operation
1. Residues from manufacturing processes
and logs curing
1. Problem will stop after a few hours of
operation
Heater produces a whistling noise when
burner is lit
1. Turning gas control knob to HI position
when burner is cold
2. Air in gas line
1. Turn gas control knob to LO position and
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local propane/LP or natural gas company
3. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice
3. Dirty or partially clogged burner orifice
Glass soots
1. Flame impingement on logs
2. Debris around burner air mixer
1. Adjust the log set so that the flame does
not excessively impinge on it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
Fireplace produces a clicking/ticking noise
just after burners are lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common. If noise is excessive,
contact qualified service person
Remote does not function
1. Battery is not installed or battery power
is low
1. Replace 9-volt batteries in receiver and
remote control
For more information, visit www.desatech.com
108661-01E
TROUBLESHOOTING
31
31
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
•
•
•
•
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Fireplace produces unwanted odors
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, page 20)
Fireplace shuts off in use
1. High or gusting winds
1. Fireplace has been tested for up to
40mph winds. However, extreme conditions may occur. See Lighting Instructions on page 25
2. Contact local propane/LP or natural gas
company
3. Clean pilot (see Cleaning and Maintenance, page 28)
4. Locate and correct all leaks (see Checking Gas Connections, page 20)
5. Tighten glass
2. Low line pressure
3. Pilot is partially clogged
4. Inner vent pipe leaking exhaust gasses
into system
5. Glass too loose and air tight gasket leaks
in corners after usage
6. Bad thermopile or thermocouple
7. Improper vent cap installation
6. Replace faulty component
7. Check for proper installation and freedom from debris or blockage
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement
above
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, page 20)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, page 20)
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing Logs,
Lava Rock, and Glowing Embers, page 24)
2. Clean out air holes at burner inlets. Periodically repeat as needed
3. Remove blockage
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
For more information, visit www.desatech.com
108661-01E
32
REPLACEMENT PARTS
SPECIFICATIONS
SERVICE HINTS
TECHNICAL SERVICE
REPLACEMENT PARTS
SERVICE HINTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
When Gas Pressure Is Too Low
PARTS UNDER WARRANTY
Contact authorized retailers of this product. If they can not supply
original replacement part(s), call DESA International’s Customer
Service Department at 1-866-672-6040.
When calling DESA International, have ready
• your name
• your address
• model and serial numbers of your fireplace
• how fireplace was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
•
•
•
•
pilot will not stay lit
burners will have delayed ignition
fireplace will not produce specified heat
propane/LP gas supply might be low (propane/LP units only)
You may feel your gas pressure is too low. If so, contact your local
gas supplier.
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. If so, contact DESA International’s Customer
Service Department at 1-866-672-6040. When calling please have
your model and serial numbers of your heater ready.
You can also visit DESA International’s technical service web site
at www.desatech.com.
Contact authorized retailers of this product. If they can not
supply original replacement part(s), call DESA International at
1-866-672-6040 for referral information.
When calling DESA International, have ready
• model number of your fireplace
• the replacement part number
SPECIFICATIONS
CHDV32NR
(V)T32N(R)
CTDV36NR
(V)T36N(R)
(V)T32P(R)
(V)T36P(R)
12,000/18,000 Btu/hr
18,000/26,000 Btu/hr
11,000/17,000 Btu/hr
17,000/24,000 Btu/hr
Natural
Natural
Propane/LP
Propane/LP
Piezo
Piezo
Piezo
Piezo
Manifold Pressure
3.5" w.c.
3.5" w.c.
10.0" w.c.
10.0" w.c.
Minimum Inlet Supply Pressure
5.5" w.c.
5.5" w.c.
11.0" w.c.
11.0" w.c.
Btu
Gas Type
Ignition
Dimension, Inches/mm (HxWxD)
Fireplace (Actual size of
firebox. Measurements do not 32 1/4" x 34 1/2" x 16 5/8" 36" x 41" x 21 1/8" 32 1/4" x 34 1/2" x 16 5/8" 36" x 41" x 21 1/8"
include nailing flanges or
819 x 876 x 422 mm 914 x 1041 x 537 mm 819 x 876 x 422 mm 914 x 1041 x 537 mm
standoffs).
Carton
Weight, lbs/kg*
Fireplace
Shipping
33 1/2" x 37 1/2" x 17 1/2"
38" x 44" x 22"
33 1/2" x 37 1/2" x 17 1/2"
38" x 44" x 22"
851 x 953 x 445 mm 965 x 1118 x 559 mm 851 x 953 x 445 mm 965 x 1118 x 559 mm
80 lbs/36 kg
83 lbs/38 kg
120 lbs/55 kg
123 lbs/56 kg
80 lbs/36 kg
83 lbs/38 kg
120 lbs/55 kg
123 lbs/56 kg
*For refractory lined models add 45 pounds for 32" models and 60 pounds for 36" models.
For more information, visit www.desatech.com
108661-01E
ACCESSORIES
33
33
ACCESSORIES
Notice: All accessories may not be available for all
fireplace models.
Purchase these fireplace accessories from your local retailer. If they
can not supply these accessories, call DESA International’s Sales
Department at 1-866-672-6040. for information. You can also write
to the address listed on the back page of this manual.
BRICK LINER
DEFLECTION HOODS
(Not Shown)
HD32 - 32" Hood - Black (2" Brow)
HD36 - 36" Hood - Black (2" Brow)
PERIMETER TRIM KIT
(Not Shown)
BL32D - 32" Refractory Brick Liner Kit
BL36D - 36" Textured Refractory Brick Liner Kit
BL36DS - 36" Standard Refractory Brick Liner Kit
BL36DH - 36" Textured Refractory Herringbone Brick Liner Kit
BL36DHS - 36" Standard Refractory Herringbone Brick Liner Kit
PT32 - 32" Perimeter Trim Kit - Black
PT32B - 32" Perimeter Trim Kit - Brushed Brass
PT32P - 32" Perimeter Trim Kit - Platinum
PT32PB - 32" Perimeter Trim Kit - Polished Brass
PT36 - 36" Perimeter Trim Kit - Black
PT36B - 36" Perimeter Trim Kit - Brushed Brass
PT36P - 36" Perimeter Trim Kit - Platinum
PT36PB - 36" Perimeter Trim Kit - Polished Brass
This brick liner adds a touch of style to your direct-vent fireplace.
Complete installation and operation instructions included in this manual.
MANUAL BLOWER KIT - BK
(Not Shown)
FLEXIBLE GAS LINE CONNECTOR - GA5081
(Not Shown)
For all models.
PROPANE/NATURAL GAS CONVERSION KIT
(Not Shown) Included with CHDV32 and CTDV36
Models
PCDM-32T - Propane/LP Gas Conversion Kit for 32" Direct-Vent
Millivolt Fireplace
PCDM-36T - Propane/LP Gas Conversion Kit for 36" Direct-Vent
Millivolt Fireplace
NCDM-32T - Natural Gas Conversion Kit for 32" Direct-Vent
Millivolt Fireplace
NCDM-36T - Natural Gas Conversion Kit for 36" Direct-Vent
Millivolt Fireplace
FACE/LOUVER PANEL KIT
(Not Shown)
RLD32 - 32" Rolled Louver Panels - Black
RLD36 - 36" Rolled Louver Panels - Black
FPD36 - 36" Filligree Panel Kit - Black
FPD36B - 36" Filligree Panel Kit - Brushed Brass
FPD36P - 36" Filligree Panel Kit - Platinum
FPD36PB - 36" Filligree Panel Kit - Polished Brass
LOUVER TRIM KIT (Rolled Louvers Only)
(Not Shown)
LT32B - 32" Rolled Louver Trim Kit - Brushed Brass
LT32P - 32" Rolled Louver Trim Kit - Platinum
LT32PB - 32" Rolled Louver Trim Kit - Polished Brass
LT36B - 36" Rolled Louver Trim Kit - Brushed Brass
LT36P - 36" Rolled Louver Trim Kit - Platinum
LT36PB - 36" Rolled Louver Trim Kit - Polished Brass
Manual variable control blower accessory
provides better heat distribution. Complete installation and operation instructions included in this manual.
THERMOSTATICALLYCONTROLLED BLOWER
KIT - BKT
Provides better heat distribution. Blower
turns off and on automatically, as needed.
Complete installation and operation instructions included in this manual.
RECEIVER AND HAND-HELD
THERMOSTAT REMOTE
CONTROL KIT
GHRCT(A) SERIES
OL
ER
TE
MER
MP
TO
F
Allows the fireplace to be operated in a
manually or thermostatically-controlled
mode. You can adjust your heat settings and
turn the heater on or off without leaving the
comfort of your easy chair.
RECEIVER AND HAND-HELD
ON/OFF REMOTE CONTROL
KIT GHRC SERIES
Allows the heater to be turned on and off
conveniently.
WALL MOUNTED THERMOSTAT CONTROL
KIT GWMT1 (Not Shown)
Allows easy wall access for thermostatic operation of your fireplace.
For more information, visit www.desatech.com
108661-01E
WAR
CO
AU
ON
OF
34
ILLUSTRATED PARTS BREAKDOWN
(V)T32N, (V)T32NB, (V)T32NR, (V)T32NRB
(V)T32P, (V)T32PB, (V)T32PR, (V)T32PRB, CHDV32NR
ILLUSTRATED PARTS
BREAKDOWN
(V)T32N, (V)T32NB
(V)T32NR
(V)T32NRB
(V)T32P, (V)T32PB
(V)T32PR
(V)T32PRB
CHDV32NR
22-3
6
22-4
22-5
22-6
7
22-2
22-1
8
4
1
12
9
14
3
17
21
19
15
11
20
10
18
9-17
9-19
13
16
9-16
9-15
9-1
9-2
2
9-13
9-8
9-3
16
9-7
9-18
5
9-9
9-14
9-6
9-12
9-11
9-4
9-5
9-10
For more information, visit www.desatech.com
108661-01E
PARTS LIST
(V)T32N, (V)T32NB, (V)T32NR, (V)T32NRB
(V)T32P, (V)T32PB, (V)T32PR, (V)T32PRB, CHDV32NR
35
35
PARTS LIST
(V)T32N, (V)T32NB, (V)T32NR, (V)T32NRB, (V)T32P,
(V)T32PB, (V)T32PR, (V)T32PRB, CHDV32NR
This list contains replaceable parts used in your fireplace. When ordering
parts, follow the instructions listed under Replacement Parts on page 32 of
this manual.
KEY PART
NO. NUMBER
1
2
3
**
**
108892-01
108892-02
109155-01
4
108903-01
5
109155-02
108903-02
6
7
8
9
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
9-14
9-15
108895-01
109096-01
**
108885-01
108885-02
11102
11105
11179
11237
14389
14390
14492
14500
14253
14511
14528
104506-25
14514
104509-02
26808
26827
108886-01
DESCRIPTION
Firebox Assembly
Face Weldment
Door Assembly (T & CHDV Models Only)
Door Assembly (VT Models Only)
Top Stamped Panel Assy
T32N/P, T32NB/PB Models
Top Rolled Louver Assy T32NR/PR,
T32NRB/PRB & CHDV32NR Models
Bottom Stamped Panel Assy
T32N/P, T32NB/PB Models
Bottom Rolled Louver Assy (T32NR/PR,
T32NRB/PRB, CHDV32NR Models)
Fireplace Top
Fireplace Top Insulation
Fireplace Surround
Burner Assembly (Natural)
Burner Assembly (Propane/LP)
Screw #8-32 x 3/8 PPH Zinc
Screw #10 x 1/2 Zinc
Screw #10-24 x 1/4 Zinc
Screw, Trilab M4 x 8mm
Millivolt Valve (Natural)
Millivolt Valve (Propane/LP)
Piezo Ignitor
Brass Fitting
Flexible Connector
Ignitor Bracket
Brass Elbow Fitting
Orifice (Natural)
Orifice (Propane/LP)
Aluminum Tubing Assy
Valve Bracket
Switch Bracket
Base Grate Assembly
KEY PART
QTY. NO. NUMBER
1
1
1
1
1
1
9-16 108891-01
9-17 108084-02
108084-03
9-18 108889-01
9-19 27113
10
108890-01
11
108897-01
1
12
13
109082-03
108901-01
1
1
1
1
1
1
2
9
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
14
108901-02
15
16
17
18
19
20
21
22
22-1
22-2
22-3
22-4
22-5
22-6
11418
108440-01
109479-01
14123
21171
24353
24460
109222-01
109403-01
109404-01
109407-01
109406-01
109405-01
109408-01
DESCRIPTION
Burner
Pilot Assembly (Natural)
Pilot Assembly (Propane/LP)
Burner Base Assembly
Air Deflector
Burner Base Gasket
Rear Refractory Brick Panel
(B Models Only)
Heat Shield
Right Refractory Brick Panel
(B Models Only)
Left Refractory Brick Panel
(B Models Only)
Push-On Nut
Screen
Screen Rod
Strain Relief
Gas Knock-Out Cover
Handy Box Assembly
Gas Conduit Assembly
Log Set
Front Log (Log 1)
Rear Log (Log 2)
Base Log (Log 3)
Crossover Log (Log 4)
Left Top Log (Log 5)
Right Top Log (Log 6)
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
25487
Lava Rock/Bag Assy
27253
Notice Label
55240
Vent Label
PCDM-32T Conversion Kit (CHDV32NR only)
** Not a field replaceable part.
For more information, visit www.desatech.com
108661-01E
QTY.
1
1
1
1
36
ILLUSTRATED PARTS BREAKDOWN
(V)T36N, (V)T36NB, (V)T36NR, (V)T36NRB
(V)T36P, (V)T36PB, (V)T36PR, (V)T36PRB, CTDV36NR
ILLUSTRATED PARTS
BREAKDOWN
(V)T36N, (V)T36NB, (V)T36NR, (V)T36NRB,
(V)T36P, (V)T36PB
23-5
23-6
(V)T36PR, (V)T36PRB
CTDV36NR
6
23-3
23-4
23-2
23-1
7
8
4
1
12
22
9
14
3
17
21
15
11
20
10
18
19
9-17
9-19
13
16
9-16
9-1
9-2
9-15
9-20
9-8 9-13
9-3
9-7
2
16
9-18
5
9-9
9-14
9-11
9-12
9-6
9-4
9-5
9-10
For more information, visit www.desatech.com
108661-01E
PARTS LIST
(V)T36N, (V)T36NB, (V)T36NR, (V)T36NRB
(V)T36P, (V)T36PB, (V)T36PR, (V)T36PRB, CTDV36NR
37
37
PARTS LIST
This list contains replaceable parts used in your fireplace. When
ordering parts, follow the instructions listed under Replacement
Parts on page 32 of this manual.
(V)T36N, (V)T36NB, (V)T36NR, (V)T36NRB, (V)T36P,
(V)T36PB, (V)T36PR, (V)T36PRB, CTDV36NR
KEY
NO.
PART
NUMBER
1
2
3
**
**
108010-01
4
108010-02
108687-01
108011-01
5
108687-02
108011-02
6
7
8
9
9-1
9-2
9-3
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
108015-01
108016-01
**
108074-01
108074-02
11102
11105
11179
11237
14389
14390
14492
14500
14508
14511
14528
104506-23
14596
14576
26808
** Not a field
replaceable part.
DESCRIPTION
QTY.
Firebox Assembly
Face Weldment
Door Assembly
(T and CTDV Models Only)
Door Assembly (VT Models Only)
Top Panel Louver Assy
T36N/P, T36NB/PB Models
Top Rolled Louver Assy; CTDV36NR,
T36NR/PR, T36NRB/PRB Models
Bottom Panel Louver Assy
T36N/P, T36NB/PB Models
Bottom Rolled Louver Assy
CTDV36NR, T36NR/PR,
T36NRB/PRB Models
Fireplace Top
Fireplace Top Insulation
Fireplace Surround
Burner Assembly (Natural)
Burner Assembly (Propane/LP)
Screw #8-32 x 3/8 PPH Zinc
Screw #10 x 1/2 Zinc
Screw #10-24 x 1/4 Zinc
Screw, Trilab M4 x 8mm
Millivolt Valve (Natural)
Millivolt Valve (Propane/LP)
Piezo Ignitor
Brass Fitting
Flexible Connector
Ignitor (SIT) Bracket
Brass Elbow Fitting
Orifice (Natural)
Orifice (Propane/LP)
Aluminum Tubing Assy
Valve Bracket
(V)T36N, (V)T36NR
(V)T36P, (V)T36PR
___
___
___
___
1
1
1
1
1
1
1
1
1
1
1
1
1
2
9
4
1
1
1
1
2
1
1
1
1
1
1
1
KEY
NO.
9-14
9-15
9-16
9-17
9-18
9-19
9-20
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23-1
23-2
23-3
23-4
23-5
23-6
PART
NUMBER
26827
108007-01
104504-03
108084-02
108084-03
108075-01
27113
109144-01
108076-01
see below
see below
see below
see below
11418
12105
108719-01
14123
21171
24353
24460
109082-01
109006-01
109007-01
110182-01
109008-01
107347-01
109009-01
107348-01
DESCRIPTION
Switch Bracket
Base Grate Assy
Burner
Pilot Assembly (Natural)
Pilot Assembly (Propane/LP)
Burner Base Assembly
Air Deflector
Air Baffle (Natural Gas Only)
Burner Base Gasket
Rear Refractory Brick Panel
Top Refractory Brick Panel
Right Refractory Brick Panel
Left Refractory Brick Panel
Push-On Nut
Screen
Screen Rod
Strain Relief
Gas Knock-Out Cover
Handy Box Assembly
Gas Conduit Assembly
Heat Shield
Log Set
Rear Log (Log 1)
Front Log (Log 2)
Crossover Log (Log 3)
Right Top Log (Log 4)
Base Log (Log 5)
Left Top Log (Log 6)
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE - NOT SHOWN
25487
Lava Rock/Bag Assy
27253
Notice Label
55240
Vent Label
PCDM-36T Conversion Kit (CTDV36NR Only)
T36NB, T36NRB
T36PB, T36PRB
VT36NB, VT36NRB
VT36PB, VT36PRB
CTDV36NR
DESCRIPTION
108080-02
108081-02
108082-02
108083-02
108080-01
108081-01
108082-01
108083-01
Rear Refractory Brick Panel
Top Refractory Brick Panel
Right Refractory Brick Panel
Left Refractory Brick Panel
For more information, visit www.desatech.com
108661-01E
QTY.
1
1
1
1
QTY.
1
1
1
1
38
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
LIMITED WARRANTY
DIRECT-VENT FIREPLACE
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase,
provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under
this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating
condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained through authorized
retailers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original factory replacement parts
voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a
result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and
any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY
IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY
OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
108661 01
NOT A UPC
108661-01
Rev. E
08/02
For more information, visit www.desatech.com
108661-01E