Technical data | DeWalt DW820 Grinder User Manual

DW820
English (original instructions)
3
Copyright DEWALT
2
Figure 1
a
b
d
e
c
Figure 2
f
d
1
Figure 3B
Figure 3A
c
l
l
Figure 4
Figure 5
k
j
k
i
i
g
h
g
h
Figure 6
2
ENGLISH
ANGLE GRINDER
DW820
General Power Tool Safety Warnings
Congratulations!
You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional power tool users.
Technical Data
Voltage
Type
Power input
No-load/rated speed
Wheel diameter
Grinding Wheel thickness
Wheel Type
Spindle diameter
Weight
VAC
W
min-1
mm
mm
kg
DW820-ZA
230
1
680
11000
100
6
27
M10
1.87
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
3
EN GLI S H
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
4
d)
e)
f)
g)
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
Safety Instructions for All Operations
a) This power tool is intended to function
as a grinder. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
b) Operations such as sanding, wire
brushing, polishing and cutting-off are not
recommended to be performed with this
power tool. Operations for which the power
tool was not designed may create a hazard and
cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
ENGLISH
d) The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool. Accessories running faster
than their rated speed can break and fly apart.
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories can not be adequately guarded or
controlled.
l) Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
f) The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheel for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
j) Hold power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electrical shock.
m) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
FURTHER SAFETY INSTRUCTIONS
FOR ALL OPERATIONS
Causes and Operator Prevention
of Kickback
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given
below:
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start
5
EN GLI S H
up. The operator can control torque reaction or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction
opposite to the wheel’s movement at the point
of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due to flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Safety Warnings Specific for
Grinding Operations
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The guard must be securely attached
to the power tool and positioned for
maximum safety, so the least amount of
wheel is exposed towards the operator. The
guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel
and sparks that could ignite clothing.
Wear eye protection.
DATE CODE POSITION (FIG. 1)
The date code (e), which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Angle grinder
1 Guard
1 Side handle
c) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off
wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them
to shatter.
1 Two pin spanner
d) Always use undamaged wheel flanges
that are of correct size and shape for your
selected wheel. Proper wheel flanges support
the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.
• Take the time to thoroughly read and
understand this manual prior to operation.
e) Do not use worn down wheels from larger
power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.
1 Flange set
1 Instruction manual
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. On/off switch
Residual Risks
b. Spindle lock button
In spite of the application of the relevant safety
regulations and the implementation of safety
d. Side handle
6
c. Guard
ENGLISH
INTENDED USE
Your DW820 angle grinder has been designed for
professional grinding applications.
DO NOT use grinding wheels other than centre
depressed wheels and flap-disc.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These heavy-duty angle grinders are professional
power tools. DO NOT let children come into
contact with the tool. Supervision is required when
inexperienced operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fig. 2)
WARNING: Before using the tool,
check that the handle is tightened
securely.
WARNING: The side handle should
always be used to maintain control of
the tool at all times.
Electrical Safety
Screw the side handle (d) tightly into one of the
holes (f) on either side of the gear case.
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Mounting and Removing the Guard
(fig. 3)
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(Middle East and Africa)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see Technical Data). The minimum conductor
size is 1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
CAUTION: Guards must be used with
this grinder.
TO MOUNT THE GUARD
1. Place the angle grinder on a table, spindle up.
2. Press the guard (c) down (fig. 3A).
3. Position the guard between your body and work
piece.
4. Tight the screw (l) holding the cinch collar
firmly around the neck of spindle (fig. 3B)
TO REMOVE THE GUARD
1. Loosen the screw (l) holding the cinch collar
around the neck of the spindle.
2. Lift up on the guard.
Fitting and Removing a Grinding Disc
(fig. 1, 4, 5)
WARNING: Do not use a damaged
disc.
7
EN GLI S H
1. Place the tool on a table, guard up.
2. Fit the backing flange (g) correctly onto the
spindle (h) (fig. 4).
3. Place the disc (i) on the flange (g). When fitting
a disc with a raised centre, make sure that the
raised centre (j) is facing the flange (g).
4. Screw the outer flange (k) onto the spindle (h)
(fig. 5). The ring on the flange (k) must face
towards the disc when fitting a grinding disc.
5. Press the spindle lock button (b) and rotate the
spindle (h) until it locks in position.
6. Tighten the flange (k) with the two pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (k) with
the two pin spanner.
Prior to Operation
• Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
• Be sure the inner and outer flange are mounted
correctly.
• Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
the tool.
Proper Hand Position (fig. 1, 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (d), with the other hand on the body of the
tool, as shown in Figure 6.
Switching On and Off (fig. 1)
WARNING: Do not switch the tool on
or off when under load.
WARNING: Before using the tool,
check that the handle is tightened
securely.
To start the tool, slide the on/off slider switch (a)
toward the front of the tool. To stop the tool, release
the on/off slider switch.
For continuous operation, slide the switch toward
the front of the tool and press the forward part of the
switch inward.
To stop the tool while operating in continuous mode,
press the rear part of the slider switch and release.
OPERATION
Spindle Lock (fig. 1)
Instructions for Use
The spindle lock (b) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
WARNING:
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
• Ensure all materials to be ground or
cut are secured in place.
Metal Applications
• Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
When using the tool in metal applications, make
sure that a residual current device (RCD) has been
inserted to avoid residual risks caused by metal
swarf.
• Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
If the power supply is shut off by the RCD, take the
tool to an authorised DEWALT repair agent.
WARNING: In extreme working
conditions, conductive dust can
8
ENGLISH
accumulate inside the machine housing
when working with metal. This can
result in the protective insulation in the
machine becoming degraded with a
potential risk of an electrical shock.
To avoid build-up of metal swarf inside the machine,
we recommend to clear the ventilation slots on a
daily basis. Refer to Maintenance.
Using Flap Discs
WARNING: Metal dust build-up.
Extensive use of flap discs in metal
applications can result in the increased
potential for electric shock. To reduce
this risk, insert an RCD before use
and clean the ventilation slots daily by
blowing dry compressed air into the
ventilation slots inaccordance with the
below maintenance instructions.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Pop-off Brushes
The motor will be automatically shut off indicating
that the carbon brushes are nearly worn out and that
the tool needs servicing. The carbon brushes are
not user-serviceable. Take the tool to an authorised
DEWALT repair agent.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
9
10
11
12
Afghanistan
Ariana Hafiz Zabi Co. Ltd.
Dahan Bagh Squire Karte Ariana, Kabul, Afghanistan
info@arianahafiz.com
Algeria
Sarl Outillage Corporation
08, Rue Med Boudiaf (ex TELLA Achen)
Cheraga, Alger
hakim.merdjadi@outillage-dz.com Tel: 213-0-21375130
lyes@outillage-dz.com
213-0-21375131
Mali.faiza@outillage-dz.com;
Fax: 213-0-21369667
sidahmed@outillage-dz.com
Angola
Angoferraria, Lda.
Rua Robert Shields, nº 61, Luanda, Angola
angoferraria@gmail.com
Tel: 244-222-395837 / 244-222-395034
sequeira.angoferraria@gmail.com Fax: 244-222-394790
Azerbaijan
Royalton Holdings Ltd.
41 Khagani St. Apt. 47 AZ1001 Baku- Azerbaijan
jai@royaltonholdings.com
office@royaltonholdings.com
Egypt
ElFarab S.A.E.
15-Nabil El Wakkad Street, Dokki,
Giza, Egypt
elfarab@elfarab.com
Tel: 202-37603946
adel.ezzat@elfarab.com
Fax: 202-33352796
mahmoud.elhosseiny@elfarab.com
Ethiopia
Seif Tewfik Sherif
Arada Sub City, Kebele 01/02, Global Insurance Bldg.,
2nd Flr., Room 43, P.O. Box 2525, Addis Ababa
seif@ethionet.et
nawanag@ethionet.et
Tel: 251-11-1563968
251-11-1563969
Fax: 251-11-1558009
Iraq
Al-Sard Co. for General Trading Ltd
Jbara Bldg. 3Flr. Al Rasheed St., Baghdad, Iraq
dewalt.service@yahoo.com
Tel: 964-18184102
Jordan
Amman West Stores-Bashiti
210 Garden St. Tla’a Ali, P.O. Box 1564
Tla Ali Amman 11953, Jordan
ali@bashitistores.com
yousef@bashitistores.com
Tel: 962-6-5350009
Fax: 962-6-5350012
Kenya
Dextron Tools Ltd.
P.O. Box 20121-00200, Shariff House,
Kimathi Street, Nairobi
info@alibhaishariff.co.ke
dextron@alibhaishariff.co.ke
Tel: 254-20-6905000
254-20-2358021
Fax: 254-20-6905111 / 254-20-6905112
Lebanon
Est. Shaya & Azar S.A.R.L.
Boulvard Jdeideh - Mar Takla - Bouchrieh .
P.O. Box 90545, Jdeideh. Beirut – Lebanon
shayazar@dm.net.lb
Tel: 961 1 872305
961 1 872306
Fax: 961 1 872303
Libya
North Africa Trading ( El Ghoul Brothers)
P.O. Box 348, 7 October Street 11
Benghazi
maryam_farooq2003@yahoo.com Tel: 218-061-3383994
nagte@eim.ae
Fax: 218-092-7640688
dewalt_libya@yahoo.com
North Africa Trading ( El Ghoul Brothers)
AlBarniq DEWALT Center,
Mokhazin-elsukar St. ElFallah, Tripoli
dewalt_libya@yahoo.com
North Africa Trading ( El Ghoul Brothers)
AlHilal Service Center Tawergha St., Misurata
Tel: 93-0-799331079
Fax: 93-0-700007576 / 93-0-799331079
Tel: 994-12-4935544
Fax: 994-12-5980378
Tel: 218-021-3606430
Fax: 218-092-6514813
Tel: 218-091-3221408
Mauritius
Robert Le Marie Limited
Old Moka Road, Bell Village, P.O. Box 161,
Port Louis
a.blackburn.rlm@rlmgroup.mu
jm.pierrelouis.rlm@rlmgroup.mu
Tel: 230-212 1865
230-212 2847
Fax: 230-2080843
Morocco
Ets Louis Guillaud & Cie
31, Rue Pierre Parent,
Casablanca – 21000
boumadiane.azedine@elg.ma
doukkali.marouane@elg.ma
Tel: 522-301446 / 305971 / 317815 /
315576
Fax: 522-444518 / 317888
Nigeria
Meridian Power Tools Ltd.
braj@meridian-nigeria.com
Gr. Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun
Stadium, Near National Stadium Surulere, Lagos, Nigeria
Tel: 234-1-7740431
234-1-7740410
Fax: 234-1-7913798
Pakistan
Northern Toolings (Pvt) Ltd.-Lahore
86- Railway Road, Lahore – 7
Pakistan
zhayee@northern.pk
import@northern.pk
sales@northern.pk
Tel: 92-423-7651220
92-423-7641675
Fax: 92-423-7641674
Northern Toolings (Pvt) Ltd.-Karachi
224-231 Industrial Town Plaza, Shahrah-e-Liaqat,
Karachi, Pakistan
karachibr@northern.pk
Tel: 92-213-2465305
92-213-2465307
Fax: 92-213-2465301
Northern Toolings (Pvt) Ltd.-Taxila
Al-Rehman Plaza, Opposite Tehsil Court,
Faisal Shaheed Road, Taxila
taxilabr@northern.pk
Tel: 92-51-4545811
Fax: 92-51-4544194
South
Africa
Benray Tool Wholesalers C.C.
dewaltservice@benray.co.za
91 Turffontein Road, Stafford, Johannesburg, 2001 P.O. zain@benray.co.za
Box 260037 EXCOM 2023, South Africa
shafiq@benray.co.za
Tel: 27-11-6838350
Fax: 27-11-6837456
Tanzania
General Motors Investment Ltd.
14 Vingunguti-Nyerere Road, P.O.Box 16541,
Dar es Salaam, Tanzania
ezra@gmi-tz.com
info@gmi-tz.com
chiwelesa@yahoo.com
Tel: 255-22-2865022 /
2862661 / 2862671 / 2862659
Fax: 255-22-2862667
Tunisia
Ets. Mohamed Ghorbel
03 Rue 8603 Charguia I Tunis.
Postal Code 2035
slim.ghorbel@gnet.tn
moh.ghorbel@gnet.tn
mourad.ghorbel@gnet.tn
Tel: 216-71794248
216-71793848
Fax: 216-71770759
Uganda
The Building Center (u) Ltd.
52 Station Road, Kitgum House,
P.O. Box 7436 Kampala, Uganda
tbc@africaonline.co.ug
chris@tbcu.co.ug
Tel: 256-041-4234567
256-041-4259754
Fax: 256-041-4236413
Yemen
Middle East Trading Co. (METCO)
5th Flr.Hayel Saeed Anam Bldg.
Al-Mugamma St. Taiz,
Yemen
tamer.metco@gmail.com
tamer@metcotrading.com
metco@metcotrading.com
sami@metcotrading.com
Tel: 967-4-213455
Fax: 967-4-219869
Middle East Trading Co. (METCO)
Mualla Dakka,
Aden
tamer.metco@gmail.com
tamer@metcotrading.com
metco@metcotrading.com
Tel: 967-2-222670
Fax: 967-2-222670
Middle East Trading Co. (METCO)
Hayel st., Sana'a,
Yemen
tamer.metco@gmail.com
tamer@metcotrading.com
metco@metcotrading.com
Tel: 967-1-204201
Fax: 967-1-204204
UAE
Bahrain
Kuwait
Oman
Qatar
KSA
Black & Decker (Overseas) GmbH
P.O. Box 5420, Dubai
service.mea@blackdecker.com Tel: 971-4 8127400 / 8127406
Fax: 971-4 2822765
Ideal Star Workshop Eqpt. Trading LLC
P.O. Box 37116, Al Quoz, Dubai
idealeq@emirates.net.ae
Tel: 971-4 3474160
Fax: 971-4 3474157
Alebrah Engineering Service
P.O. Box 78954, Al Qusais, Dubai
alebrah@eim.ae
Tel: 971-4 2850044
Fax: 971-4 2844802
Burj Al Madeena
Industrial Area No. 1, opp. Pakistani Masjid
P.O. Box 37635, Sharjah
dewaltuae@hotmail.com
Tel: 971-6 5337747
Fax: 971-6 5337719
McCoy Middle East LLC
P.O. Box 25793, Sharjah
mccoy@emirates.net.ae
Tel: 971-6 5395931
Fax: 971-6 5395932
McCoy Middle East LLC
P.O. Box 10584, Ras Al Khaimah
mccoyrak@gmail.com
Tel: 971-7 2277095
Fax: 971-7 2277096
Al Sukoon Gen. Trdg. Co. LLC
P.O. Box 2975, Ajman
sukoon@eim.ae
Tel: 971-6 7435725 / 7438317
Fax: 971-6 7437350
Zillion Equipment and Spare Parts Trading LLC
zilliontrdg@gmail.com
P.O. Box 19740, opp. Bin Sadal / Trimix Redymix Sanaiya, Al Ain
Tel: 971-3 7216690
Fax: 971-3 7216103
Light House Electrical, Abu Dhabi Branch
P.O. Box 120, Abu Dhabi
dewalt_lhe@hotmail.com
Tel: 971-2 6726131
Fax: 971-2 6720667
Light House Electrical, Musaffah Branch
P.O. Box 120, Abu Dhabi
dewalt_lhe@hotmail.com
Tel: 971-2 5548315
Fax: 971-2 5540461
Alfouz Services Co. WLL
P.O. Box 26562, Tubli, Manama
alfouz@batelco.com.bh
Tel: 973 17783562 / 17879987
Fax: 973 17783479
Kavalani & Sons W.L.L.
P.O. Box 71, Sitra, Manama
info@kavalani.com
pradeep@kavalani.com
Tel: 973 17732888
Fax: 973 17737379
Al Omar Technical Co.
P.O. Box 4062, Safat 13041, Kuwait
alexotc@usa.net
Tel: 965 24848595 / 24840039
Fax: 965 24845652
Fawaz Al Zayani Establishment
P.O. Box 42426, Shop No.18,
Al Humaizi Commercial Complex, Khalifa Al Jassim, Shuwaikh
dewaltkuwait@hotmail.com
Tel: 965 24828710
Fax: 965 24828716
Fawaz Al Zayani Establishment
Fahaheel Industrial Area, Main St., Sanaya
dewaltkuwait@hotmail.com
Tel: 965 23925830
Fax: 965 24828716
Al Jizzi Company LLC
P.O. Box 1704, P.C. 112, Ruwi
aljizied@omantel.net.om
jizzi10@omantel.net.om
Tel: 968 24832618 / 24835153
Fax: 968 24831334 / 24836460
Al Hassan Technical & Construction Supplies Co. LLC
P.O. Box 1948, P.C. 112, Ruwi
hamriya.sr@al-hassan.com
abrar.h@al-hassan.com
Tel: 968 24810575 / 24837054
Fax: 968 24810287 / 24833080
Oman Hardware Co. LLC
P.O. Box 635, Ruwi Postal Code 112
omanhard@omantel.net.om
Tel: 968 24815131
Fax: 968 24816491
Khimji Ramdas
P.O. Box 19, Post Code 100, Ghala, Muscat
bilal.m@khimjiramdas.com
Tel: 968 24595906/ 907
Fax: 968 24852752
Teyseer Industrial Supplies & Services Co. WLL
55, Al Wakalat St. (Between St. 18 & 19)
Salwa Industrial Area, P.O. Box 40523 Doha
manish@tissco-qatar.com
tool.service@tissco-qatar.com
Tel: 974 4581536
Fax: 974 4682024
Shaheen Electrical Works & Trading Co. WLL
Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha
shaheenelc@gmail.com
Tel: 974 460 02 30 / 460 05 25
Fax: 974 460 13 38
Industrial Material Organization (IMO)
P.O. Box 623, Rail Street, Riyadh
service@imo.com.sa
Tel: 966-1 4028010 Ext. 26
Tel: 966-1 8001245757
Fax: 966-1 4037970
Fawaz Ebrahim Al Zayani Trading Est.
P.O. Box 76026, Al Raka : 31952
dewaltdammam@hotmail.com
Tel: 966-3 8140914
Fax: 966-3 8140824
MSS (Al-Mojil Supply & Services)
P.O. Box 450, Jubail 31951
Opp-Gulf Bridge Library & Riyadh House
mssjubail@almojilservices.com Tel: 966-3 3612850 / 3624487
alex.chang@almojilservices.com Tel: 966-3 3621729
Fax: 966-3 3623589 / 3620783
EAC (Al Yousef Contg. & Trdg. Est.)
P.O. Box 30377, Jeddah -21477
golamkibria77@yahoo.com
Tel: 966-2 6519912
Fax: 966-2 6511153
Mohamed Ahmed Bin Afif Est.
P.O. Box 530, Yanbu, Al Bahr
binafifyanbu@hotmail.com
Tel: 966-4 3222626 / 3228867
Fax: 966-4 3222210
Garziz Trading for Bldg Mat & Decoration
P.O. Box 3364, Madina
agarziz@yahoo.com
Tel: 966-4 826 14 90 / 822 76 36
Fax: 966-4 826 57 41
Sultan Garment Factory (RSC)
P.O. Box 29912, Riyadh 11467
rscservice@digi.net.sa
Tel: 966-1 4055148 / 4042889
Fax: 966-1 4055148
Al Bawardi Tools & Hardware
P.O. Box 112, Dammam 31411
asattar@albawardi.com
nibanez@albawardi.com
Tel: 966-3 8330780 Ext. 24
Tel: 966-3 8348585 Ext. 24
Fax: 966-3 8336303
Al Bawardi Tools & Hardware
P.O. Box 68, Riyadh 11411
rbaltao@albawardi.com
asamad@albawardi.com
Tel: 966-1 4484999
Fax: 966-3 4487877
Al Bawardi Tools & Hardware
P.O. Box 16905, Jeddah 21474
sharadji@albawardi.com
fgaber@albawardi.com
Tel: 966-2 6444547 / 6439035
Tel: 966-2 6456095
Fax: 966-2 6439024
N413096
09/14
Download PDF

advertising