Dialogic DM/IP481-2T1-PCI-100BT Network Card User Manual

Dialogic®
DM/IP Boards
Physical Description
*Channels: 4 3 2 1
Red
Yellow
Green
Loopback
Quick Install Card for PCI 100 Base-T
„
DM/IP481-2T1-PCI-100BT
„
DM/IP601-2E1-PCI-100BT
10
9
8
Part number 64-0031-02
Copyright © 2001-2007
Dialogic Corporation.
All Rights Reserved.
Caution! All computer boards are sensitive to
electrostatic discharge (“ESD”). Handle all staticsensitive boards and components at a static-safe work area,
and observe anti-static precautions at all times.
7
Configuring the Hardware
Board Identification
The DM3 device driver, part of the system software,
assigns board instance numbers in ascending order
(beginning with 0) as it detects each board in your system.
A board instance number is the board identification
number used by the system software to recognize the
board. Refer to the Dialogic® Configuration Manager
4.
General Network Interface Alarm LED
5.
Power LED
6.
Reset LED
7.
SW1: Rotary switch to set board
identification (UNIX systems only).
8.
Alarm LEDs: Indicate network alarms for
each trunk.
Red: Alarm to indicate loss of signal.
Yellow: Alarm to indicate loss of frame
synchronization at far end of external
network.
Green: Indicates signal present; powered up
and receiving signal from external sources.
Loopback: Indicates loopback mode is
activated.
9.
CT/MVIP Bus Termination Jumpers*:
Bus signal is terminated when the
corresponding jumper is installed.
JP2A: CT Bus termination jumper
JP2B: MVIP Bus termination jumper
10.
P3: CT Bus connector
1
3
2
2
JP2A
JP2B
Unpack the Dialogic® DM/IP Board (“board”) according
to the following steps:
Note: Place boards in static-shielding bags when carrying
boards from station to station.
CAUTION: Do not remove the board from the anti-static
packaging until you are ready to install it. Observe proper
anti-static precautions at all times.
RJ-48C jacks: Connectors (4) to external
digital telephone network interface.
4
Unpacking the Board
3.
Good Link LED
3.
6
5
1
Prepare a static-safeguarded work area.
Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the
board’s components.
Lay the board on the static-dissipative work
surface.
2.
12
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall to learn more.
1.
2.
Ethernet Interface Connector
11
Before You Begin
Protecting the Board from Damage
1.
11.
ISA Edge Retainer
12.
Signal Processing Daughterboard
*Note: Signal must be terminated only on
boards at each end of the CT Bus cable.
(DCM) utility to retrieve the board instance (ID)
number(s) assigned to the board(s) in your system.
then run the Dialogic® Configuration Manager (DCM) to
configure the system.
NOTE: If you add a board to the system, the existing
board instance (ID) numbers may change, depending upon
the PCI bus and slot number where the new board is
installed.
1. With your computer on the static-safe work area,
switch off the power and disconnect all power cords
from the electrical outlets.
The system software does not recognize or use the setting
number of the rotary switch (SW1) to determine the board
ID number. However, you must set SW1 to a unique
number for each DM3 board in your system so that the
power on self test for the board(s) can complete
successfully.
Use a non-magnetic screwdriver to turn SW1 to one of the
15 board ID settings, 1-9 and A-F.
See the DCM On-Line Help for more details on board
identification.
Installing the Hardware
NOTE: If you are running in a Windows NT
environment, install the software, install the board(s), and
2. Remove the cover, select an empty expansion bus
slot, and remove the slot’s retaining screw and
access cover plate.
3. Use the slot’s board guides as you insert the board
edge connector into the slot. Press firmly until the
board is securely seated in the slot. If you are not
installing your board in an ISA form factor PCI slot,
remove the ISA edge retainer.
4. Replace and tighten the retaining screw to secure the
board.
5. Select a new slot and repeat steps 3 and 4 for each
board you are installing.
6. Use the CT Bus cable to connect the board you are
installing to other boards in the system.
NOTE: Your system may include both CT Bus boards
and SCbus boards. To connect both board types, you
must install a CT Bus/SCbus Adapter on one of the CT
Bus boards in a system. See the CT Bus/SCbus
Adapter Quick Install Card for installation details for
the Adapter and the bus cables.
7. Replace the computer cover when finished and
reconnect the power cords.
CAUTION: If your BIOS is set up to use Plug and Play
functionality, and there are non-DM3 ISA cards in the
system, a conflict can be created because the DM3
card could use the same IRQs that are assigned to an
ISA card. This could cause the machine to stop
responding. You can remove the conflict by
determining which IRQs are used by the non-DM3
ISA cards in the system and reserving them, in the
BIOS, for ISA use only.
Connecting to the RJ-48C Jack
RJ-48C Cable Connector
RJ-48C Jack
After Installing the
Hardware
After installing the hardware, run the Dialogic®
Configuration Manager (DCM) as described in the
installation instructions included with the Dialogic®
System Software to configure your system.
For technical specifications and product information go to:
http://www.dialogic.com/products.htm.
Warranty and Return
Information
Warranty Period
For specific warranty information for this board, refer to
the Warranty section of the Products page, located at this
URL: http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products
through a network of value added distributors who are
trained to answer technical questions on installing and
configuring Dialogic® products. If you are unsure how
to contact your support channel, please call Dialogic
in the United States at 973-967-6600 (9am-5pm EST)
and we will assist in obtaining the appropriate support
channel. Outside the United States please refer to
http://www.dialogic.com/support/contact to obtain
local contact information.
Dialogic also provides direct support via Dialogic® Pro™
Services agreements. For more details of direct support
from Dialogic please refer to:
http://www.dialogic.com/support/DialogicPro.
Returning a Product
To return a board for warranty repair or any other returns,
please refer to the following:
http://www.dialogic.com/support/hwfaults. To return a
board for warranty repair, please refer to the following:
http://www.dialogic.com/support/hwfaults. For all other
returns, contact your vendor or Dialogic Customer Support
(for more information, see
http://www.dialogic.com/support/contact/ ).
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales Office
for your area. Address, telephone and fax numbers, are
available at the Dialogic website located at:
http://www.dialogic.com/contact.htm.
To purchase Dialogic® products, please refer to the
following website to locate the appropriate supplier.
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and
are subject to change without notice and do not represent a commitment on
the part of Dialogic Corporation or its subsidiaries (“Dialogic”).
Reasonable effort is made to ensure the accuracy of the information
contained in the document. However, Dialogic does not warrant the
accuracy of this information and cannot accept responsibility for errors,
inaccuracies or omissions that may be contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN
CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY
INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT
BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO
LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY
EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR
USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life
sustaining, critical control or safety systems, or in nuclear facility
applications.
It is possible that the use or implementation of any one of the concepts,
applications, or ideas described in this document, in marketing collateral
produced by or on web pages maintained by Dialogic may infringe one or
more patents or other intellectual property rights owned by third parties.
Dialogic does not provide any intellectual property licenses with the sale of
Dialogic products other than a license to use such product in accordance
with intellectual property owned or validly licensed by Dialogic and no
such licenses are provided except pursuant to a signed agreement with
Dialogic. More detailed information about such intellectual property is
available from Dialogic’s legal department at 9800 Cavendish Blvd., 5th
Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all
users of its products to procure all necessary intellectual property
licenses required to implement any concepts or applications and does
not condone or encourage any intellectual property infringement and
disclaims any responsibility related thereto. These intellectual property
licenses may differ from country to country and it is the responsibility
of those who develop the concepts or applications to be aware of and
comply with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and
SIPcontrol, among others, are either registered trademarks or trademarks of
Dialogic. Dialogic's trademarks may be used publicly only with permission
from Dialogic. Such permission may only be granted by Dialogic’s legal
department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada
H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to
full respect of the trademark guidelines published by Dialogic from time to
time and any use of Dialogic’s trademarks requires proper
acknowledgement. The names of actual companies and products
mentioned herein are the trademarks of their respective owners.