Diamond Multimedia DV170J/JB Computer Monitor User Manual

Diamond Digital
DV170J/JB
Colour TFT LCD Monitor
17” (43 cm) LCD Panel Size
Copyright 2005, Mitsubishi Electric Australia Pty. Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
Table of Contents
1
2
3
4
5
6
7
8
9
10
Important Safety Instructions ..........................................1
Features.............................................................................2
Unpacking the Monitor .....................................................3
Hardware Installation .......................................................5
Windows driver installation .............................................7
Setting the Display Resolution ........................................8
Choosing the Best Resolution...........................................8
Supported Graphics Modes and Refresh Rate Selection..9
Adjusting the Monitor.....................................................13
User Controls ..................................................................13
Adjusting the Monitor's Display .......................................14
OSD Function Menu .......................................................14
Function Description .......................................................14
Frequently Asked Questions .........................................18
Specifications .................................................................20
Service Contacts.............................................................22
i
Disclaimer
Mitsubishi Electric Australia Pty. Ltd. makes no representations or warranties,
either expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, Mitsubishi Electric Australia reserves the right to
revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
Diamond Digital is a registered trademark of Mitsubishi Electric Australia Pty. Ltd.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
All other trademarks remain the property of their respective owners.
Reference Information
For future reference, write the following information about your monitor in
the space below. The serial number is found on the back of the product or
on the bottom of its stand.
Monitor Information
Product Name:
DV170J/JB
Serial Number:
Date of Purchase:
Dealer Information
Dealer:
Telephone
Number:
Address:
ii
1
Important Safety Instructions
Please read the following safety instructions before installing or cleaning your
Diamond Digital monitor:
1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do
not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor
housing.
2. Slots and openings on the back or top of the cabinet are provided for
ventilation. They must not be blocked or covered. This product should
never be placed near or over a radiator or other heat source, or used in a
built-in installation unless proper ventilation is provided.
3. Never push objects of any kind, or spill liquid of any kind into this product.
4. Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltages or other hazards.
5. Do not apply pressure to the LCD screen. Excess pressure can damage
the LCD panel.
6. If any abnormal operation or accident (such as dropping the unit) occurs,
disconnect the monitor from the wall power outlet and contact qualified
service personnel.
7. Turn the audio volume control of the built-in speakers to minimum (0) and
turn the monitor off before connecting or disconnecting any audio cable.
1
2 Features
Your DV170J/JB Monitor features:
♦ XGA (1280 x 1024 pixel) Resolution LCD Panel
♦ High Brightness Level – 270 cd/m2 (typical)
♦ High Contrast Ratio – 450:1 (typical)
♦ Response Rate – 12 ms (Typical) (Tr+Tf)
♦ True Colour Display
With 16.2M (6bit + FRC) colour, the DV170J/JB monitor offers you better
image quality.
♦ High Quality Ratiometric Expansion
With any resolution within the monitor’s specified range, your Diamond
Digital DV170J monitor can expand the image to full screen.
♦ Plug and Play Compatibility with Microsoft® Windows® 95, 98, 2000,
Me and XP
♦ Space Saving - only 190 mm deep
♦ Light Weight - only 5 kg
♦ Lower Power Consumption
40W maximum during operation with audio.
♦ Power Saving
Power management complies with VESA DPMS standard. When the
system is idle (in monitor off mode), the monitor automatically cuts its
power consumption to less than 3 W.
♦ On Screen Display
Allows you to adjust all settings simply using on-screen menus.
♦ Support Kensington security locks
2
3 Unpacking the Monitor
Please check that the following items are included with your monitor. If they are
missing or damaged, please contact your place of purchase immediately.
LCD monitor
User’s Manual
r's
Use nual
Ma
VGA Cable
Power Cord
3
Locate the model name and the serial number label on the back of your monitor,
and write the details of the monitor and your place of purchase in the space on
page (ii) of this manual for future reference.
4
4 Hardware Installation
Connecting the Monitor Base
Remove the base from the packing box and place
it on the desk. Next, remove the LCD display and
carefully seat it on the base. (See fig.1-1 )
Figure 1-1
Viewing Angle Adjustment
The LCD Monitor is designed to allow users
to have a comfortable viewing angle. The
viewing angle can be adjusted from -5°to
+30°.(See fig. 1-2)
Figure 1-2
5
Connecting the Display to your Computer
Using the VGA cable
1. Power off your computer.
2. Connect one end of the VGA signal cable to the LCD
Monitor’s VGA port. (See Fig 1-3)
3. Connect the other end of the signal cable to the VGA
port on your PC.
4. Make sure connections are secure.
Figure 1-3
Connecting the AC Power
1. Connect the power cord to the monitor. (See Fig. 1-4)
2. Connect the power cord to an AC power source.
Figure 1-4
Instructions for VESA Mounting
To detach the LCD Monitor from its stand, unscrew the
two screws n for the monitor stand and pull it downwards
to remove, then unscrew the four screws o for the
monitor stand bracket and pull this down to remove.
Figure 1-6
Interface for Arm Applications
Before installing the mounting device, please refer to
Fig.1-7.
The rear of this LCD display has four integrated 4 mm, 0.7
pitch threaded nuts, as well as four 5mm access holes in
the plastic covering as illustrated in Figure 1-2. (These
specifications meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard).
6
Figure 1-7
5 Windows driver Installation
The DV170J/JB is fully Windows Plug and Play compatible so no specific
Windows drivers are required for installation.
Windows 98, ME, and 2000
The first time you start Windows after connecting your new monitor, the system
will detect the monitor and automatically start the Add New Hardware wizard.
Just follow the prompts to load the native Plug and Play drivers.
Windows XP
The first time you start Windows after connecting your new monitor Windows
XP will automatically load the native Plug and Play drivers.
7
6 Setting the Display Resolution
Choosing The Best Resolution
All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as
the maximum resolution that may be displayed on the LCD. In the case of the
DV170J/JB the LCD resolution is 1280 x 1024 pixels. This is also known as the
“native” resolution of the monitor. Lower resolutions can be displayed at full
screen through an interpolation circuit. Because the lower resolution must be
expanded, the quality of the displayed image is not as good as that available
when the native resolution is displayed. For optimal performance from any LCD
monitor, you must use the monitor’s native resolution.
If you are using Windows 95, 98, 2000, Me, XP or NT 4.0, you can change the
resolution as follows:
1.
Double-click the Display icon in the control panel.
2.
From the Display Properties dialogue box, select the Settings tab.
There is a slider on the right-hand side in the middle of the dialogue box
that alters the displayed resolution. Set the resolution to 1280 x 1024.
3.
For Windows NT users only: select a refresh rate of 60Hz and click Test.
A test pattern will be displayed. Make sure that there are no error
messages shown by the monitor. If an error message is displayed, check
the resolution and refresh rate settings or choose a different refresh rate.
4.
Click OK to close Display Properties.
8
If you are using an Apple Macintosh, change the resolution by doing the
following:
MacOS 8.x/9.x
1.
Click the Apple icon at the top, left corner of the screen, select Control
Panel and then select Monitors.
2.
Select a resolution of 1280 x 1024 pixels with between 60Hz refresh rate.
3.
If refresh rates of 60Hz are not available, click Recommended in the
Show drop-down box and change it to All. Select the resolution and
refresh rate as above.
A colour depth of either Thousands or Millions is recommended.
MacOS X
1.
Click the Apple icon at the top, left corner of the screen, select System
Preferences and then select Displays.
2.
Select a resolution of 1280 x 1024 pixels with between 60Hz refresh rate.
3.
A colour depth of either Thousands or Millions is recommended.
Supported Graphics Modes and Refresh Rate Selection
There is no need to choose the highest possible refresh rate when using an
LCD monitor. It is not technically possible for an LCD monitor to flicker. Even at
a refresh rate of 60 Hz you will get an absolutely flicker-free image.
For best results, it is important that you set the graphics adaptor to use one of
the monitor’s preset display modes shown in Table 1 on the next page. Other
graphics signals may be displayed poorly or not at all. Note that the
DV170J/JB’s preset modes correspond to VESA or Apple Macintosh standard
graphics signals for these resolutions. All recent models of graphics adaptor
should be able to support these modes. For the native resolution of 1280 x
1024 pixels, for example, refresh rates of 60, 70 and 75 Hertz are supported.
With Windows 95, 98, ME, 2000 or XP you can change the refresh rate of the
9
graphics signal as follows:
1. Double click the Display icon in the control panel.
2. From the Display Properties dialogue box, select the Settings tab and
click the Advanced Properties button.
3. For Windows 95, 98, and ME select the Adapter tab, for 2000 and XP
select the Monitor tab. The refresh rate selection field is located in the
centre, at the bottom of the dialogue box.
4. Choose a refresh rate that corresponds with one of the factory modes from
the table below.
5. Click Apply, and then OK twice.
Please Note:
• Graphics modes that are not listed in the table may not be supported. For
an optimal picture it is recommended that you choose a graphics mode
with a resolution of 1280 x 1024 pixels that is listed in Table 1 on the next
page. Resolutions of 640 x 480, 800 x 600 and 1024 x 768 pixels are
supported. The default setting may require some adjustment before use.
• The displayed image may show some distortion or noise that can be
caused by the signal from the VGA card if it does not correspond with the
usual standard. This is not however, a problem with the monitor. If it is still
visible after using the Automatic adjustment, you can usually improve the
displayed image by manually adjusting the phase, horizontal position and
pixel frequency settings using the "Geometry" menu. See Chapter 7,
Adjusting the Monitor, for more details.
• When you shut Windows down you may see interference lines on your
screen. This caused by the manner in which Windows controls the
graphics card at this point and is normal with all LCD monitors.
• To extend the service life of the product, we recommend that you use your
computer's power management functions to turn the monitor off after
extended idle periods.
10
Table 1
Standard Timing Table
If the selected timing is NOT included in table below, this LCD monitor will use the
most suitable available timing.
TIMING
FH(KHZ
SYNC
)
FV(HZ) POLARITY
640x350
31.469
+
VGA-350
70.087
–
640x400
24.83
–
NEC PC9801
56.42
–
640x400
31.469
–
VGA-GRAPH
70.087
+
640x400
31.5
–
NEC PC9821
70.15
–
640X480
31.469
VESA-PAL
50.030
640x480
31.469
–
VGA-480
59.94
–
640x480
35.00
–
APPLE MAC-480
66.67
–
640x480
37.861
–
VESA-480-72Hz
72.809
–
640x480
37.5
–
VESA-480-75Hz
75
–
720x400
31.469
–
VGA-400-TEXT
70.087
+
832x624 APPLE
49.725
–
MAC-800
74.55
–
800x600
35.156
+
SVGA
56.25
+
800x600
37.879
+
VESA-600-60Hz
60.317
+
800x600
48.077
+
VESA-600-72Hz
72.188
+
TIMING
FH(KHZ
SYNC
)
FV(HZ) POLARITY
800x600
VESA-600-75Hz
1024x768
XGA
1024x768
COMPAQ-XGA
1024x768
VESA-768-70Hz
1024x768
VESA-768-75Hz
46.875
75
48.363
60.004
53.964
66.132
56.476
70.069
60.023
75.029
+
+
–
–
+
+
–
–
+
+
TOTAL
ACTIVE
SYNC
(DOT/
LINE)
800
449
848
440
800
449
800
449
800
629
800
525
864
525
832
520
840
500
900
449
1152
667
1024
625
1056
628
1040
666
TOTAL
(DOT/
LINE)
640
350
640
400
640
400
640
400
640
480
640
480
640
480
640
480
640
480
720
400
832
624
800
600
800
600
800
600
ACTIVE
WIDTH
(DOT/LINE)
96
2
64
8
96
2
64
2
96
2
96
2
64
3
40
3
64
3
108
2
64
3
72
2
128
4
120
6
SYNC
PORCH
PORCH
FOREQ
(DOT/LINE) (DOT/LINE) (MHZ)
16
48
25.175
37
60
64
80
21.05
7
25
16
48
25.175
12
35
16
80
25.197
13
34
16
48
25.175
62
85
16
48
25.175
10
33
64
96
30.24
3
39
16
120
31.5
1
20
16
120
31.5
1
16
18
54
28.322
12
35
32
224
57.2832
1
39
24
128
36
1
22
40
88
40
1
23
56
64
50
37
23
FRONT
BACK
PIXEL
(DOT/
LINE)
1056
625
1344
806
1328
816
1328
806
1312
800
(DOT/
LINE)
800
600
1024
768
1024
768
1024
768
1024
768
WIDTH
(DOT/LINE)
80
3
136
6
176
4
136
6
96
3
PORCH
PORCH
FOREQ
(DOT/LINE) (DOT/LINE) (MHZ)
16
160
49.5
1
21
24
160
65
3
29
16
112
71.664
8
36
24
144
75
3
29
16
176
78.75
1
28
11
FRONT
BACK
PIXEL
1024x768
APPLE MAC-768
1152x864
(60Hz)
1152x864
(70Hz)
1152x864
(75Hz)
1280x960
(60Hz)
1280x960
(70Hz)
1280x960
(75Hz)
1280x1024VESA1024-60Hz
1280x1024VESA1024-75Hz
60.24
75.02
54.054
59.270
63.851
70.012
67.50
75.00
60.00
60.00
70.00
70.00
75.00
75.00
64
60
80
75
–
–
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
1328
803
1480
912
1480
912
1600
900
1800
1000
1800
1000
1800
1000
1688
1066
1688
1066
1024
768
1152
864
1152
864
1152
864
1280
960
1280
960
1280
960
1280
1024
1280
1024
96
3
96
3
96
3
128
2
112
3
112
3
112
3
112
3
144
3
32
3
40
13
32
1
64
2
96
1
96
1
96
1
48
1
16
1
176
29
192
32
200
44
256
32
312
36
312
36
312
36
248
38
248
38
Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but cannot
be expanded to full
12
80
80
94.499
108.00
108.00
126.00
135.00
108
135
7
Adjusting the Monitor
User Controls
A brief description and the location of all LCD Monitor function controls and
indicators:
Figure 2-1
1
Soft Power Switch
2
Power-On Indicator
3
4
Function Select
Buttons
Adjustment Control
Buttons
Press the power switch to switch the monitor ON/OFF.
LED lights Green color --- Power is ON.
LED lights Yellow --- Monitor is in "Power Saving Mode".
LED is off --- Power is OFF.
Press either left or right control button for OSD (On Screen Display)
menu selection.
Press the left button to decrease the OSD setting and press the right
button to increase the OSD setting.
13
Adjusting the Monitor's Display
The monitor has four function control buttons to select among functions shown on OSD menu,
designed for easy user-viewing environments.
OSD Function Menu
To access the OSD Main menu, simply press one of
the Function Select control buttons, and the menu
diagram will pop up on the screen as shown on Fig.
2-2:
Continue pressing the Function Select buttons to
scroll through the available menu items, then press
the Adjustment Control buttons to adjust the setting
of a selected item.
Figure 2-2
Function Description
Icon
Function
Function Description
Brightness
This function lets you increase and decrease the screen brightness.
Contrast
This function lets you increase and decrease the contrast level of the
screen.
H. Position
V. Position
Sharpness
OSD
Transparency
This function let's you adjust the display's horizontal position. (Not
available when using DVI).
This function let's you adjust the display's vertical position. (Not
available when using DVI).
This function let's you adjust the images sharpness. Five selections are
available. A smoother setting is more suitable for pictures, while a
sharper setting is more suitable for text. (Not available when using DVI).
This function let's you set the transparency of the OSD menu (Not
available when using DVI).
Phase
This lets you adjust the phase of the pixel clock to eliminate sampling
noise (Not available when using DVI).
Clock
Adjusts the sampling frequency for the Analogue (VGA) to Digital signal
conversion (Not available when using DVI).
14
This function lets you select a colour temperature. Using the Adjustment
Colour
Temperature Control buttons to select the required colour temperature. Please see
the diagram below for function and description. (Not available when
using DVI).
OSD H. Position This function moves the OSD menu window horizontally.
OSD V. Position This function moves the OSD menu window vertically.
Graph / Text
Recall
Language
Auto and Input
Select
Exit
Because the H and V-Frequencies of both 640 x 400 70Hz, and 720 x
400 70Hz, are the same, this function let's you manually select either
640 x 400 (graphics mode), or 720 x 400 (text mode) when running in
DOS. (Not available when using DVI).
The recall function will return all adjusted parameters to factory preset
values.
Five OSD language options are available: English, German, French,
Spanish, and Italian. Press the left or right adjustment control button to
select other language.
This function lets you use the Automatic adjustment function to adjust
the Geometry based on the displayed image, or select either the
Analogue or Digital inputs
Exits the OSD menu.
TABLE 1
Icon
9300
7500
6500
User
Function
Description
CIE coordinated Colour Temperature of
9300°K
CIE coordinated Colour Temperature of
7500°K
CIE coordinated Colour Temperature of
6500°K
Three colours (Red, Green, Blue) can be
adjusted from the OSD menu
Sets the CIE coordinate colour
temperature to 9300°K
Sets the CIE coordinate colour
temperature to 7500°K
Sets the CIE coordinate colour
temperature to 6500°K
Allows a user to define the CIE
Temperature settings.
Picture Optimisation
The easiest way to obtain an optimal picture is by using the Auto function in the
OSD menu. This only works reliably if the graphics adaptor is set to use one of
the monitor’s factory modes (see Table 1 in the previous chapter) and if you
are displaying a suitable stationary image (such as the Windows desktop).
15
The monitor will remember the settings obtained by the auto calibration
settings and use them whenever you turn the monitor on. Note that you may
need to readjust the monitor if it is connected to a different computer or if the
computer’s graphics adaptor is replaced.
If you are still not satisfied with the result, you can enhance the image by using
the monitor’s manual adjustment functions.
Manual Picture Adjustment
Adjustments to the displayed image and audio volume are made using the
On-Screen Display (OSD), and the buttons on the front of the monitor.
To manually adjust the image:
1.
2.
3.
4.
Display your operating system desktop
Open the OSD menu by pressing one of the Function keys on the monitor.
Press Fn► or ◄ to select the Clock function.
Press ► or ◄ to increase or decrease the sampling clock to get the
optimum picture. Look closely at the picture displayed, especially
surrounding text and icons, for any movement or change. Adjust the Clock
setting and see how this affects this “noise” or movement. Make sure that
in correcting noise in one part of the screen the setting does not create it in
another. You should, with careful adjustment, be able to obtain a picture
with no visible noise in any section of the screen.
5. If some noise or distortion is still visible select Phase using the Fn► or ◄
buttons.
6. With the Clock set to the optimal value adjust the Phase to further optimise
the displayed image. You should now be able, with a combination of the
Phase and Clock settings, to obtain a perfectly stable image.
7. Finalise the manual adjustment using the H. Position and V. Position
functions
If you are still not satisfied with the result, try repeating the above procedure
using a graphics signal that has a different refresh rate.
16
Please Note:
You must use one of the factory modes when manually adjusting the picture. If
you are having difficulties generating a supported mode, ask your computer
dealer or the distributor or manufacturer of your graphics card for assistance.
The procedures described in this chapter should be performed for every
resolution and type of graphics signal that you wish to use. For example, if a
particular application requires a resolution of 800 x 600 pixels, but all other
applications use the monitor’s native resolution, you will need to display the
test pattern and make adjustments twice.
The monitor will remember your settings and use them whenever you turn the
monitor on. Note that you may need to re-adjust the monitor if it is connected to
a different computer or if the computer’s graphics adaptor is replaced.
17
8
Frequently Asked Questions
The image is blurred, how can I get the best quality picture?
♦
♦
Read chapter 6, Setting the Display Resolution, and select a graphics
signal with the correct resolution and refresh rate. Then read chapter 7,
Adjusting the Monitor, and make adjustments to the displayed image
based on these instructions.
Have you used a VGA extension cable?
If so, remove the extension cable and check the displayed image. Has the
image quality improved? Optimise the image using the procedures in
chapter 7 with the extension cable removed. Reconnect the extension
cable once the image has been optimised. Depending on the
characteristics and type of the extension cable, some blurring or distortion
may occur due to conduction losses of the extension cable. You can
minimise these losses by using an extension cable with better conduction
quality or with a built-in booster.
♦
Does the blurring only occur at resolutions lower than the native
(maximum) resolution?
Please read chapter 6, Setting the Display Resolution. Select a graphics
signal that uses the monitor’s the native resolution (1280 x 1024 pixels).
Why does the image look yellow, blue or pink instead of showing the
correct colours?
♦
The most common cause of this problem is a loose VGA signal cable or
connector. Check that the cable is securely connected to the computer.
♦
Check the VGA signal cable for damage. If any pins are bent or broken off,
contact your dealer or an authorised Mitsubishi Electric service agent (see
Chapter 10 for details).
18
No image is displayed, what can I do?
♦
Check that the light (LED) next to the monitor’s power button is lit and is
green in colour. If the LED is green, press one of the Function Select
buttons on the monitor to access the On Screen Display. If the message
NON PRESET MODE appears there, please read chapter 6, Setting the
Display Resolution and reset the graphics card to one of the monitor’s
supported graphics signals.
♦
If the LED is orange the monitor is in power saving mode. Press a button
on the computer keyboard or move the mouse to wake the computer. If that
does not help, check that the VGA cable is securely plugged into the
computer. Also check the pins of the VGA cable’s connector. If any pins are
bent or broken off, then contact your dealer (see Chapter 10 for details).
♦
If the LED is not lit at all, check that the monitor is plugged into the power
supply mains socket and that the power switch is turned on. Check that the
monitor’s power switch is also turned on.
The image is or distorted, flashes or flickers:
♦
Check that the monitor’s signal cable is securely connected to the
computer.
♦
Read the chapters 6 and 7 of this manual, then select the correct
resolution, refresh rate and make adjustments based on these instructions.
The image is displaced in one direction:
♦
Use the H. Position (horizontal position) adjustment in the monitor’s OSD
to reposition the image.
♦
Read the chapters 6 and 7 and then select the correct resolution, refresh
rate and make adjustments based on these instructions.
19
9
Specifications
Model:
DV170J/JB
Display Characteristics
Display Type
17“ active matrix Thin Film
Transistor Liquid Crystal Display
Viewable Diagonal Area
43 cm / 17”
Native (Maximum) Resolution
1280 x 1024 pixels
Colours
16 million (6 bit + FRC)
Contrast Ratio
450:1 (typical)
Brightness
260 cd/m² (typical)
Response Time
12 ms (typical)
Viewing Angle (Horizontal, Vertical)
-60°/+60°, -40°/+60°(typical)
Dot Pitch
0.264mm x 0.264 mm
User Interface
Controls
Power switch with LED indictor
On-Screen Display Functions
Contrast, Brightness, Vert. & Hor.
Position, Phase, OSD Position,
Auto Adjustment, Clock,
Graph/Text, language, Recall,
Colour Temperature, Exit,
Sharpness, OSD Transparency
Microprocessor Controlled Graphics
Modes
28 Preset modes:
20
Including 11 VESA & 4 DOS
Input Signal
Line Frequency
24 – 80kHz multi-frequency
Image Frequency (Refresh Rate)
49 - 75Hz
Video Signal
RGB analogue (Positive polarity)
0.7 Vpp/75 Ohm
Synchronization
TTL separate, composite TTL
Signal Connection
15-pin mini D-sub
Physical Characteristics
Power Management
VESA DPMS, Energy Star
Maximum Power Consumption
48 Watts
Power Saving Mode
< 3 Watts
Operating Voltage
Automatic switched mode power
supply, 100 - 240 V, 50 - 60 Hz
Dimensions (W x H x D)
374mm x 387mm x 190mm
Weight
5 kg
Temperature (Operating)
5°C - 40°C
Air Humidity (Operating)
20% - 80%
Regulatory Certification
Safety
AS/NZS 60950:2000
EMI/EMC
AS/NZS CISPR22:2002 (C-Tick).
Other
ISO 13406-2
21
10 Service Contacts
If problems remain after checking this manual, please contact your place of
purchase or contact:
Australian Service Contacts
Visit the Customer Support section of Mitsubishi Electric Australia’s web site at
www.mitsubishielectric.com.au
for details of your nearest Mitsubishi Electric Authorized Service Center or
contact the Service Department for your state:
New South Wales and Australian Capital Territory
348 Victoria Road
Rydalmere, NSW, 2116
Telephone: (02) 1300 651-808
Fax:
(02) 9684-7684
Queensland
12 / 469 Nudgee Road
Hendra, QLD, 4030
(Airlink Business Park)
Telephone: (07) 3623-2000
Fax:
(07) 3630-1888
South Australia and Northern Territory
77 Port Road
Hindmarsh, SA, 5007
Telephone: (08) 8340-0444
Fax:
(08) 8340-0555
22
Victoria and Tasmania
4 / 303 Burwood Hwy
East Burwood, VIC, 3151
Telephone: (03) 9262-9899
Fax:
(03) 9262-9850
Western Australia
5 / 329 Collier Road
Bassendean, WA, 6054
Telephone: (08) 9377-3411
Fax:
(08) 9377-3499
23