ADLINK Data Acquisition Selection Guide Selecting the right hardware, software, and accessories

ADLINK Data Acquisition Selection Guide Selecting the right hardware, software, and accessories
ADLINK Data Acquisition
Overview
ADLINK's wide range of PC-based data acquisition modules support analog input, load cell sensor measurement, analog output, digital I/O,
relay outputs, and timer/counter boards. Tailored to a wide range of applications and available in a variety of form factors including USB,
PCI, PCI Express, PXI, CompactPCI, PC/104+, and ISA, ADLINK's data acquisition modules embrace more than one hundred DAQ and DIO
modules. All ADLINK boards support NI® LabVIEW™, MATLAB ® Data Acquisition Toolbox™, Microsoft ® Visual Studio .NET, and Provide
Ready to Run Applications providing fast startup of ADLINK data acquisition modules without any programming requirement.
Programming Languages
LabVIEW︱Visual Studio.NET︱MATLAB︱BCB/Delphi
PCI︱PCI Express︱PXI︱CompactPCI︱USB
Data Acquisition Modules
ADLINK Comprehensive Product Offerings
3-1
USB DAQ
PCI Express DAQ
General-Purpose DAQ
High-Performance DAQ
Analog Output
Digital I/O High-Speed DIO
Load Cell Measurement
Timer/Counter
www.adlinktech.com
Selection Guide
1
Selecting the right hardware, software, and accessories
PXI/PXIe
PC-based data acquisition systems primarily utilize a combination of measurement hardware, accessories, and software to provide a flexible
system for automating measurement, acquiring important data for analysis, and presenting the result. Even so, such systems can constitute a
wide variety of different configurations and address multitudes of diverse applications. It is necessary, accordingly, to determine the various
parameters of use for the DAQ system, such as type of measurement, optimum interface, accuracy levels and output resolution at each data
collection point, the required number of channels, data collection speeds, and sampling rate. This selection guide provides basic overviews
and specifications for ADLINK data acquisition hardware, related accessories, and supporting software. We’ve provided these simple steps to
guide you through the process of selecting the very best ensemble of components for your data acquisition system:
Step 1: Hardware Selection
Select the hardware required to best suit your measurement applications. ADLINK provides a variety of boards for analog and digital I/O needs, with
PCI, PCI Express, PXI, CompactPCI and USB products available. Refer to the following criteria and use the table on page 3-2 to 3-4 to determine the
Interface
Channel Count
Signal Type
Step 2: Accessory Selection
Resolution
Terminal boards
Sampling Rate &
Speed
2
Modular Instruments
ideal measurement hardware for your data acquisition system.
Cables
Most applications require additional accessories,
3
normally acquired as separate items. Refer to pages
3-50 to 3-51 for details. These can include:
DAQ
Step 3: Software Selection
More than any other single factor, software can influence
system startup time, overall effectiveness, suitability for
your application, and ease of modification. Refer to
Operating
System
pages 2-1 to 2-4 for details. Major criteria in determining
a choice of software include:
Software
Compatibility
Software
Recommendations
4
Category
Page
PCI/PCIe/PXI/cPCI/USB Module: Analog Input/Output
3-1
Digital Input/Output
3-33
GPIB & Bus Expansion
Hardware
Accessory
Resources
Page
Comparison table of terminal boards and cables
3-50
Terminal boards and cables selection table
3-50
Software
Resources
Page
Primary modules and software selection tables
3-5
Software overview
2-1
8 steps to get ADLINK products ready
2-3
www.adlinktech.com 3-2
16-CH
250 kS/s
16-Bit
USB
2kS/S
4-CH
128kS/S
2MS/S
500kS/S
250kS/S
96-CH
64-CH
3MS/S
500kS/S
32-CH
250kS/S
16-CH
100kS/S
4-CH
YES
16-Bit
2-CH
1MS/S
12-Bit
1MS/S
2-CH
3-9
USB-2401(5)
3-13
2 GPIO
USB-2405
3-11
DAQ/DAQe-2010
3-18
DAQ/DAQe-2005
3-18
DAQ/DAQe-2006
3-18
DAQ/DAQe-2208
3-20
DAQ/DAQe-2204
3-21
DAQ/DAQe-2205
3-21
DAQ/DAQe-2206
3-21
PCI-9221
3-17
PCI-9222
3-17
PCI-9223
3-17
PCI-9114 Series
3-24
YES
Static
1MS/S
16-Bit
12-Bit
8 DI/4 DO
16-Bit
YES
16 DI/16 DO
400kS/S
16 DI/ 16 DO
12-Bit
16-Bit
PCI-9113
3-27
DAQ/DAQe-2213
3-23
DAQ/DAQe-2214
3-23
PCI-9111HR(1)
3-25
PCI-9112
3-26
DAQ/DAQe-2501
3-22
DAQ/DAQe-2502
3-22
PCI-6202
3-30
PCI-6308V
3-29
PCI-6308A(2)
3-29
PCI/PCIe-6208V
3-31
PCI-6208A(2)
3-31
PCI/PCIe-6216V
3-31
PXI-2010
3-18
PXI-2005
3-18
PXI-2006
3-18
PXI-2020
3-19
PXI-2022
3-19
PXI-2208
3-20
PXI-2204
3-21
PXI-2205
3-21
PXI-2206
3-21
4-CH
PXI-2501
3-22
8-CH
PXI-2502
3-22
cPCI-9116
3-28
cPCI-6216V
3-31
cPCI-6208V
3-31
2-CH
1-CH
12-Bit
14-Bit
2-CH
1MS/S
8-CH
YES
24 DI/24 DO
16 DI/16 DO
12-Bit
4-CH
8-CH
12-Bit
Static
YES
1MS/S
4-CH
24 DI/24 DO
16-Bit
16 DI/16 DO Isolated
12-Bit
4 DI/4 DO Isolated
Static
16-Bit
4 DI/4 DO
16-CH
2MS/S
4-CH
500kS/S
250kS/S
14-Bit
16-Bit
8-CH
250kS/S
16-Bit
16-CH
250kS/S
16-Bit
3MS/S
12-Bit
96-CH
64-CH
500kS/S
250kS/S
8-CH
4-CH
64-CH
400kS/S
250kS/S
16-Bit
14-Bit
2-CH
1MS/S
12-Bit
YES
24 DI/24 DO
4 DI/4 DO
2-CH
1MS/S
12-Bit
16-Bit
YES
24 DI/24 DO
8 DI/8 DO
16-CH
8-CH
Static
16-Bit
(1) HR: High gain
(2) PCI-6x08A: Current Output available
(3) Isolated analog input card
(4) Current input: 0~20 mA
4 DI/4 DO
(5) Universal input: Support voltage/current input, full/half bridge, TC, RTD, resistance measurement.
3-3
www.adlinktech.com
3-9
USB-1903
24 DI/24 DO
16-Bit
3-9
USB-1902
4 DI/2 DO
YES
12-Bit
USB-1901
(4)
250kS/S
100kS/S
8-CH
16-Bit
14-Bit
250kS/S
500kS/S
1MS/S
24-Bit
250kS/S
16-CH
2-CH
8 DI/4 DO
(3)
Isolated DIO
Relay DO
High-Density
Isolated
DIO
High-Density
Isolated DIO
0-24 V
Isolated
0-24
V
Isolated
0-28 V
Isolated
0-28 V
Isolated
0-24 V
Isolated
0-24
V
Isolated
Isolated
DIO
Isolated
DIO
Isolated
16-CH
5-35 V
Power MOSFET
USB-7230
3-15
16-CH
8-CH
16-CH
8-CH
Power MOSFET
Relay
USB-7230
USB-7250
3-13
3-15
8-CH
128-CH
8-CH
5-35 V
30 VDC, 2A
125V
AC,, 2A
0.5A
30 VDC
USB-7250
PCI-7443
3-13
3-40
128-CH
64-CH
64-CH
PCI-7443
PCI-7442
3-38
3-40
64-CH
64-CH
128-CH
PCI-7442
PCI-7444
3-38
3-40
64-CH
128-CH
PCI-7444
PCI-7433
3-38
3-41
PCI-7433
PCI-7233
3-39
3-42
PCI-7233
PCI-7432
3-40
3-41
64-CH
32-CH
32-CH
16-CH
Relay DO
Isolated
Power MOSFET
5-40V
Power MOSFET
5-35V
Darlington
5-35V
Darlington
16-CH
64-CH
32-CH
32-CH
32-CH
32-CH
64-CH
5-35V
64-CH
32-CH
5-35V
2-CH
16-CH
0-24 V
Isolated
0-24
V
32-CH
16-CH
16-CH
32-CH
16-CH
16-CH
8-CH
8-CH
8-CH
8-CH
32-CH S/W Programmable
32-CH S/W Programmable
32-CH
3-39
3-41
Darlington
(3)
PCI-7432HIR
PCI-7434
3-39
3-41
Darlington
PCI-7434
PCI-7234
3-39
3-42
350 V, 0.12 A
PhotoMos Relay
PCI-7234
PCI-7258
3-40
3-39
350 V, 0.12 A
125 VAC, 0.5 A
30
DCAC
, ,10.5
A A
125VV
30 VDC, 1 A
250 VAC, 5 A
30 VV
DCAC
, ,55AA
250
PhotoMos Relay
Latching Relay
PCI-7258
PCI-7256
3-37
3-38
Latching Relay
PCI-7256
3-36
High-Power Relay
PCI-7260
3-36
High-Power Relay
PCI-7260
3-34
Relay
PCI/LPCI/LPCIe-7250 3-37
Relay
PCI/LPCI/LPCIe-7250 3-35
30 VDC, 5 A
120 VAC, 0.5 A
24 VV
DCAC
, ,15AA
120
1.8V/2.5V/3.3V
1.8V/2.5V/3.3V
SW Selectable
SW Selectable
32-CH
32-CH
32-CH
96-CH S/W Programmable
TTL
TTL DIO
DIO
5 V TTL
5 V TTL
Counter
Isolated
Relay DO
0-24 V
Isolated
0-24 V
High-Speed
DIO
High-Speed
Isolated
DIO
3-33
PCIe-7350
3-31
PCIe-7360
3-32
80 MB/s
MB/s
12
12 MB/s
PCI/PCIe-7300A
PCI/PCIe-7200
3-34
3-33
PCI/PCIe-7200
PCI-7396
3-35
3-44
PCI-7396
PCI/PCIe-7296(1)
3-46
3-41
(1)
PCI/PCIe-7296
PCI/PCIe-7248(1)
3-43
3-41
(1)
PCI/PCIe-7248
PCI-7224(1)
3-43
3-41
PCI-7224(1)
3-43
3-45
PCI-8554
cPCI-7433
3-47
5 V TTL
5 V TTL
10-CH/16-Bit
PCI-8554
8-CH
64-CH
8-CH
64-CH
128-CH
128-CH
cPCI-7433
cPCI-7452(2)
3-41
3-43
128-CH
32-CH
128-CH
32-CH
5-35 V
Darlington
cPCI-7452
cPCI-7432
(2)
3-45
3-39
32-CH
32-CH
64-CH
5-35 V
Darlington
cPCI-7432
cPCI-7434
3-41
3-39
16-CH
64-CH
8-CH
Relay
cPCI-7434
cPCI-7252
3-41
3-35
16-CH
8-CH
120 VAC, 0.5 A
24 VV
DCAC
, ,10.5
A A
120
Relay
cPCI-7252
3-37
10-CH/16-Bit
24 VDC, 1 A
3-39
32-CH S/W Programmable
80 MB/s
cPCI-7300
3-32
32-CH S/W Programmable
80 MB/s
cPCI-7300
3-34
cPCI-7248
3-42
cPCI-7248
3-44
cPCI-8554
cPCI-8554
3-45
3-47
TTL DIO
0-24 V
48-CH S/W Programmable
5 V TTL
TTL DIO
0-24 V
48-CH S/W Programmable
5 V TTL
Timer/
Counter
Timer/Counter
PCIe-7350
200 MB/s
400 MB/s
8-CH
8-CH
8-CH
8-CH
1-CH/32-Bit Timer
&
64-Bit Counter
1-CH/32-Bit
Timer
& 64-Bit Counter
10-CH/16-Bit
10-CH/16-Bit
(1) Opto-22 compatible (2) with 6U Eurocard form factor (3) HIR: High input range
www.adlinktech.com 3-4
2
3
4
GPIB & Bus Expansion
0-24 V
Isolated
0-24
V
Isolated DIO
Relay DO
48-CH
24-CH S/W
S/W Programmable
Programmable
200 MB/s
24-CH S/W Programmable
8-CH
8-CH
Timer/
Counter
Timer/
Isolated DIO
96-CH S/W Programmable
48-CH S/W Programmable
PCI/LPCI/LPCIe-7230
3-40
PCI-7433HIR(3)
3-41
1
DAQ
1.8V/2.5V/3.3V
1.8V/2.5V/3.3V
SW Selectable
SW Selectable
PCI-7432
PCI/LPCI/LPCIe-7230 3-39
3-42
(3)
PCI-7433HIR
PCI-7432HIR(3)
24 VDC, 5 A
High-Speed
DIO
Relay
5-40V
16-CH
64-CH
2-CH
Relay DO
32-CH
125VDC, 0.5A
2-CH/32-Bit
Modular Instruments
0-50 V
Isolated
0-50
V
16-CH
PXI/PXIe
USB
USB
Isolated DIO
Relay DO
Software Selection Guide
Bus
Products
DAQ/DAQe/PXI-2005
Page
Windows ®
(Note1)
Linux ®
(Note2)
Software Compatibility
Software Recommendations
Visual
Studio.NET
(Note4)
DAQBench
DAQMaster AD-Logger Others
(Note6)
LabVIEW™
(Note3)
MATLAB ®
(Note5)
√
3-18
√
NA
3-18
√
√
√
NA
DAQ/DAQe/PXI-2010
3-18
√
√
√
NA
High-Performance DAQ
PXI-2020
3-19
√
√
√
NA
PXI-2022
3-19
√
√
√
NA
DAQ/DAQe/PXI-2204
3-21
DAQ/DAQe/PXI-2205
3-21
DAQ/DAQe/PXI-2206
3-21
DAQ/DAQe/PXI-2208
DAQ/DAQe-2213
D2KDASK
D2KDASK/X
DAQPilot
D2K-DASK
DAQPilot
DAQ_MTLB
√
√
√
NA
√
√
√
NA
NA
√
√
√
3-20
√
√
√
NA
3-23
√
√
√
NA
DAQ/DAQe-2214
3-23
√
√
√
NA
DAQ/DAQe/PXI-2501
3-22
√
√
√
NA
DAQ/DAQe/PXI-2502
3-22
√
√
√
NA
PCI-9221
3-17
√
√
√
NA
√
√
√
NA
√
√
√
NA
PCIS-
PCIS-
DASK
DASK/X
General-Purpose
DAQ
PCI-9222
3-17
PCI-9223
3-17
PCI-9111DG
3-25
√
√
√
NA
PCI-9111HR
3-25
√
√
√
NA
PCI-9112
3-26
√
√
√
NA
PCI-9113A
3-27
PCIS-
PCIS-
√
√
√
NA
PCI-9114A-DG
3-24
DASK
DASK/X
√
√
√
NA
DAQPilot
PCIS-DASK
DAQPilot
DAQ_MTLB
USB DAQ
PCI-9114DG
3-24
√
√
√
NA
PCI-9114A-HG
3-24
√
√
√
NA
cPCI-9116
3-28
√
√
√
NA
USB-1901
3-9
√
√
NA
USB-1902
3-9
√
√
NA
USB-1903
3-9
√
√
NA
USB-2401
3-13
USB-2405
3-11
UD-DASK
NA
DAQPilot
UD-DASK
DAQPilot
DAQ_MTLB
√
√
NA
√
√
NA
USB-7230
3-15
√
√
NA
USB-7250
3-15
√
√
NA
Note:
(1) Windows Support for Windows 2000/XP, and Windows 7/8 x64/x86
(2) Linux Support for Ubuntu 12.04.1 LTS, Fedora Core 17, and OpenSuSe 12.1
(3) Compatible with LabVIEW™ 8.0 and above
(4) Compatible with Visual Studio .NET 2005/2008, DASK for API, and DAQPilot for Componentware
(5) MATLAB ® Data Acquisition Toolbox 2.2 (and above) compliant
3-5
√
DAQ/DAQe/PXI-2006
www.adlinktech.com
U-Test
Bus
Analog Output
PCI-6202
Page
Windows ®
(Note1)
Linux ®
(Note2)
Software Recommendations
Visual
Studio.NET
(Note4)
DAQBench
DAQMaster AD-Logger Others
(Note6)
LabVIEW™
(Note3)
MATLAB ®
(Note5)
3-30
√
√
NA
NA
PCI/cPCI-6208-A
3-31
√
√
NA
NA
PCI/PCIe/cPCI-6208V-GL
√
√
NA
NA
√
√
NA
NA
√
√
NA
NA
PCIS-
PCIS-
3-31
DASK
DASK/X
PCI-6308A
3-29
PCI-6308V
3-29
√
√
NA
NA
PCI/PCIe-7200
3-35
√
√
√
NA
PCI-7224
3-43
√
√
√
NA
PCI/LPCI/LPCIe/cPCI-7230
3-42
√
√
√
NA
DAQPilot
PCIS-DASK
DAQPilot
DAQ_MTLB
PCI-7233
3-42
√
√
√
NA
PCI-7234
3-42
√
√
√
NA
PCI/cPCI/PCIe-7248
3-43
√
√
√
NA
PCI/LPCI/LPCIe-7250
3-33
√
√
√
NA
cPCI-7252
3-33
√
√
√
NA
√
√
√
NA
3-39
√
√
√
NA
PCI-7260
3-36
√
√
√
NA
PCI/PCIe-7296
3-43
√
√
√
NA
PCI/PCIe/cPCI-7300
3-34
√
√
√
NA
PCIe-7350
3-33
√
√
√
NA
PCIe-7360
3-32
√
√
√
NA
PCI-7396
3-46
√
√
√
NA
PCI/cPCI-7432
3-41
√
√
√
NA
PCI/cPCI-7433
3-41
√
√
√
NA
PCI/cPCI-7434
3-41
√
√
√
NA
PCI-7442
3-40
√
√
√
NA
PCI-7443
3-40
√
√
√
NA
PCI-7444
3-40
√
√
√
NA
cPCI-7452
3-45
√
√
√
NA
PCI/cPCI-8554
3-47
√
√
NA
NA
PCIS-
PCIS-
DASK
DASK/X
PCIS-
PCIS-
DASK
DASK/X
DAQPilot
DAQPilot
PCIS-DASK
DAQ_
DAQPilot
MTLB
PCIS-DASK
DAQPilot
DAQ_MTLB
www.adlinktech.com 3-6
3
4
GPIB & Bus Expansion
Timer Counter
3-38
PCI-7258
DAQ
Digital I/O
PCI-7256
2
Modular Instruments
3-31
PCI/PCIe/cPCI-6216V-GL
1
PXI/PXIe
Products
Software Compatibility
Get Connected with
ADLINK USB DAQ/DIO Modules
Portable, Reliable and Flexible USB DAQ/DIO Modules
ADLINK's USB DAQ/DIO modules leverage the expertise of ADLINK’s analog and digital design capability deliver high-performance
measurement while benefiting from the simplicity and portability of USB interfaces. Enable accurate, fast, simple setup by providing
built in signal conditioning, USB-powered, and plug-and-play USB connectivity. Reducing manpower requirements and associated
development costs while increasing overall accuracy, ADLINK's USB DAQ/DIO modules are the optimum solution for most measurement and industrial control applications.
Features Highlights
Removable screw terminal with quick
release enables easy signal connection,
with costs saved from no extension cable
or terminal board needs.
Lockable USB connector enhances
reliability, securing connection in
vibration-prone environments
USB Bus powered eliminates the need
for external power supply, suitable for
portable measurement with notebook or
I/O expansion requirements.
Multi-function stand allows
universal desktop, rail, or
wall mounting
3-7
www.adlinktech.com
Easy Device Identification via rotary control
provides convenient identification of active module
when more than one module is installed.
Built-in Signal Conditioning
1
Extra Signal Conditioning
DAQ Card & Cable & Terminal Board
Increased
Accuracy
PXI/PXIe
Signal Conditioning
Built-inExtra
Signal
ConditioningDAQ Card & Cable & Terminal Board
Increased
Accuracy
Decreased
Costs
2
Modular Instruments
Decreased
Costs
Ready-to-Use ADLINK U-Test Utility
Ready-to-Use
ADLINK U-Test Utility
U-Test is a free ready-to-use testing program allowing configuration and test data acquisition with no programming
required.
out-of-the-box
configuration
and generation
of simple
functions
, including
monitoring,
U-Test
is a Easy
free ready-to-use
testing
program allowing
configuration
and test
data acquisition
withfull
nodata
programming
logging and
analysis is easy
and fast,and
withgeneration
no programming
required.
EasyFFT
out-of-the-box
configuration
of simplerequirment.
functions , including full data monitoring,
logging and FFT analysis is easy and fast, with no programming requirment.
No programming necessary for operating and full function testing
3
No
programming
necessary for operating and full function testing
of ADLINK
USB DAQ/DIO
of ADLINK USB DAQ/DIO
Intuitive interface for data monitoring and logging, waveform
DAQ
Intuitive
interface
dataI/O
monitoring
and logging,
generation,
and for
digital
control panel
use as waveform
virtual instrument
generation, and digital I/O control panel use as virtual instrument
Useful analysis functions, such as direct cursor measurement of
Useful analysis functions, such as direct cursor measurement of
traces and real-time FFT analysis
traces and real-time FFT analysis
Data exportable to Microsoft Excel for offline analysis
Data exportable to Microsoft Excel for offline analysis
Supports auto-recollection of configuration settings for future use
Supports auto-recollection of configuration settings for future use
ADLINKUSB
USBDAQ/DIO
DAQ/DIOModules
Modules
Offering
ADLINK
Offering
Analog
Input
Analog
Input
USB-1901
USB-1901
16 16
SE/8
P-DIP-DI
SE/8
-
-
250250
kS/skS/s
-
-
16-Bit
16-Bit
-
-
16 16
SE/8
P-DIP-DI
SE/8
2
2
250250
kS/skS/s
16-Bit
16-Bit
USB-1903
USB-1903
1 MS/s1 MS/s
16-Bit
2
250 kS/s
1 MS/s
16-Bit
16-Bit
8 Current-IN
250 kS/s
16-Bit
USB-2405
4 DI,
128kS/s,
128kS/s,
24-bits (AC/DC
coupled)
2
1 MS/s
4 DI,
USB-2405
16-Bit
8 Current-IN
-
16-Bit
-
DigitalDigital
I/O I/O
4
8 DI/4 DO
8 DI/4 DO
TTL
TTL
-
-
GPIB & Bus Expansion
USB-1902
USB-1902
Analog
Output
Analog
Output
8 DI/4 DO
8 DI/4 DO
TTL
TTL
-
-
8 DI/4 DO
TTL
8 DI/4 DO
TTL
-
-
2 GPIO
2 GPIO
24-bits 4(AC/DC
coupled)
DI
4 DI
(Universal for voltage/current/full-bridge/half-bridge/TC
USB-2401
USB-2401
-
-
(Universal for voltage/current/full-bridge/half-bridge/TC
/RTD/resistor)
/RTD/resistor)
2 kS/s
24-Bit
2 kS/s
-
USB-7230
USB-7250
USB-7250
-
-
-
16-CH Isolated DI-
-
16-CH Isolated
16-CHDO
Isolated DI
2-CH Counters
16-CH Isolated DO
8-CH Relay
2-CH Counters
-
-
-
TTL
-
-
-
USB-7230
4 DI/2 DO
TTL
-
24-Bit
4 DI/2 DO
8-CH Isolated DI
8-CH Relay
-
2-CH Counters
8-CH Isolated DI
2-CH Counters
www.adlinktech.com 3-8
USB-1901/1902/1903
8/16-CH 16-Bit 250 kS/s Multi-Function USB DAQ Modules
Introduction
The ADLINK USB-1900 series provides a range of USB 2.0-based multi-functional DAQ modules.
The USB-1901 and USB-1902 16-Bit 250 kS/s USB 2.0-based high-performance DAQ modules allow
four different voltage input ranges, while the USB-1903 features additional built-in precision current-tovoltage resistors capable of direct measurement of current signal from 0 to 20 mA.
The USB-1900 series is USB bus powered and equipped with removable screw-down terminals for easy
device connectivity. The attached multi-functional stand can be used for desktop, rail, or wall mounting.
Suitable for mixed-signal tests, laboratory research, and factory automation, the USB-1900 series provide
a simple measurement solution at an affordable price.
Pin Assignment
Features
■
■
■
USB 2.0 high-speed
USB bus powered
16-CH 250 kS/s voltage input (USB-1901/1902)
8-CH 250 kS/s current input (USB-1903)
2-CH 1 MS/s voltage output (USB-1902/1903)
Analog and Digital triggering
Removable screw terminal on module
Lockable USB cable for secure connectivity
Ready-to-use testing application (U-Test) provided
USB-1901/1902
USB-1903
ECLK
20
40
AOTG*
ECLK
20
40
AOTG
NC
19
39
AITG
NC
19
39
AITG
NC
18
38
GPI7
NC
18
38
GPI7
GPO3
17
37
GPI6
GPO3
17
37
GPI6
GPO2
16
36
GPI5
GPO2
16
36
GPI5
GPO1
15
35
GPI4
GPO1
15
35
GPI4
GPO0
14
34
GPI3
GPO0
14
34
GPI3
■OS Information
DGND
13
33
GPI2
DGND
13
33
GPI2
AGND
12
32
GPI1
AGND
12
32
GPI1
*AO1
11
31
GPI0
AO1
11
31
GPI0
*AO0
10
30
DGND
AO0
10
30
DGND
AGND
9
29
AISE
AGND
9
29
AISE
AI7(AIL3)
8
28
AI15(AIL7)
CI3-
8
28
CI7-
AI6(AIH3)
7
27
AI14(AIH7)
CI3+
7
27
CI7+
AI5(AIL2)
6
26
AI13(AIL6)
CI2-
6
26
CI6-
AI4(AIH2)
5
25
AI12(AIH6)
CI2+
5
25
CI6+
AI3(AIL1)
4
24
AI11(AIL5)
CI1-
4
24
CI5-
AI2 (AIH1)
3
23
AI10(AIH5)
CI1+
3
23
CI5+
AI1 (AIL0)
2
22
AI9(AIL4)
CI0-
2
22
CI4-
AI0(AIH0)
1
21
AI8(AIH4)
CI0+
1
21
CI4+
■
■
■
■
■
■
• Windows XP, Windows 7/8 x64/x86
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• U-Test, DAQBench, DAQMaster
Standard Shipped Accessories
• One pair of 20-pin removable screw
terminals
• 2 M USB Type A to USB Mini-B
cable with lockable connector
* Not available for USB-1901
• Module stand
• Rail-mount kit
Ordering Information
■USB-1901
16-CH 16-Bit 250kS/s Analog Input USB DAQ
■USB-1902
16-CH 16-Bit 250kS/s Multi-Function USB DAQ
■USB-1903
8-CH 16-Bit Current Input Multi-Function USB DAQ
3-9
www.adlinktech.com
Optional Accessories
■RST-20P
One pair of 20-pin removable
screw terminals
■USB-2M-L
2 M USB Type A to USB Mini-B cable
with lockable connector
USB DAQ
1
PXI/PXIe
Specifications
Model Name
USB-1901
USB-1902
USB-1903
Analog Input
Resolution
Number of channels
16-Bit
16 SE / 8 Pseudo-diff, voltage input
Maximum sampling rate (single channel)
8 Current inputs
250 kS/s(Multiplexing, channel-gain-queue)
1, 5, 10, 50 1
Input range (Voltage)
± 10 V, ± 2 V, ± 1 V, ± 200 mV
N/A
Input range (Current)
Offset error
± 0.1 mV (gain=1)
±0.01 mA (typical)
Gain error
± 0.05% of FSR (gain=1)
±0.05% of FSR (typical)
CMRR (gain=1)
90 dB
-
SFDR (gain=1)
108 dB
-
SINAD (gain=1)
89 dB
-
THD (gain=1)
102 dB
-
SNR (gain=1)
89 dB
-
ENOB (gain=1)
14.5-Bit
N/A
0-20 mA
-3dB small signal bandwidth (gain=1)
600 kHz
-
FIFO buffer size
4 k samples
Trigger sources
Software, external digital, analog trigger ( from one of analog input channels)
Trigger mode
Post trigger, delay trigger, retrigger, gate trigger
External conversion source
Yes (up to 250 kS/s)
Input coupling
DC
Overvoltage protection
Input impedance
2
Modular Instruments
Programmable gain
3
Continuous ± 24 V
High impedance > 1 GΩ
Data transfer
249.5 Ω (input resistor)
DAQ
Programmed I/O, continuous (USB bulk transfer mode)
Analog Output
Number of channels
N/A
Resolution
-16-Bit
2 voltage outputs
Maximum update rate
-
Output range
-
± 10 V
Offset error
-
± 0.15 mV
Gain error
-
± 0.05% of FSR
INL
-≦1 LSB
DNL
-
Output driving capacity
± 5 mA
Slew rate
-
2.2 V/μs
Settling time (0.1% of Full scale)
-
26 μs
Rising time
-
6 μs
Falling time
-
6 μs
1 MS/s (simultaneous update)
< 1 LSB
-
10 k samples (2-CH sharing)
Output mode
-
Programmed I/O, continuous (USB bulk transfer mode)
GPIB & Bus Expansion
FIFO
4
Function I/O
Mode*
Digital I/O
General timer/counter
Pulse generation
Digital I/O, general timer/counter, pulse generation
8 DI / 4 DO (TTL level)
Two 32-Bit, base clock: 80 MHz, external to 10 MHz
Two PWM outputs (Modulation frequency: 0.01 Hz to 5 MHz; Duty cycle: 1%-99%)
General Specifications
Interface
I/O connector
Operating temperature
Storage temperature
Relative humidity
Power requirements
Dimensions
USB 2.0 high speed, mini-USB connector
Two 20-pin screw terminals
0 to 55°C (32˚F to 131˚F)
-20 to 70°C (-4˚F to 158˚F)
5 to 95% non-condensing
5V@400 mA (USB bus powered)
114 mm (H) x 156.5 mm (L) x 41.3 mm (W) (4.5” x 6.16” x 1.63”)
(without connector and stand)
Note: The function I/O share the same I/O pins. Only one of these modes can be selected.
www.adlinktech.com 3-10
USB-2405
4-CH 24-Bit 128kS/s Dynamic Signal Acquisition USB 2.0 Module
Introduction
The USB-2405 is a 24-bit high-performance dynamic signal acquisition USB module equipped with 4 analog
input channels providing simultaneous sampling at up to 128 kS/s per channel. The USB-2405 also features
software-selectable AC or DC coupling input configuration and built-in high precision 2 mA excitation
current to measure integrated electronic piezoelectric (IEPE) sensors such as accelerometers and microphones.
The USB-2405 delivers high precision, DC and dynamic measurement performance with very low temperature drift. The onboard 24-bit Sigma-Delta ADC supports anti-aliasing filtering, suppressing modulator
and signal out-of-band noise and providing usable signal bandwidth of the Nyquist rate, making it ideal for
high dynamic range signal measurement in vibration and acoustic applications.
The USB-2405 supports digital and analog trigger sources and flexible trigger modes, including post, delay,
middle, gated, and pre-triggering for efficient data acquisition with no need for post-processing. The USB2405 is USB bus-powered and equipped with BNC connectors and removable spring terminals for easy
device connectivity.
Features
■■
■■
■■
■■
■■
■■
■■
Hi-Speed USB 2.0
SB bus powered
U
24-bit Sigma-Delta ADC with built-in anti-aliasing filter
4-CH simultaneous sampling analog inputs, up to 128kS/s
AC or DC input coupling, software selectable
Analog or digital triggering
Supports 2mA excitation output on each analog input channel
for IEPE sensor measurement
■■ Full auto-calibration
■■ Ready-to-use testing application (U-Test) provided
IO connector definition
AI 3
AI 2
AI 0
■OS Information
• Windows XP, Windows 7/8 x64/x86
USB-2405
■ Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■ Software Recommendations
• U-Test, DAQBench, DAQMaster
Standard Shipped Accessories
• 4-pin removable spring
terminal
• 2 M USB Type A to USB Mini-B
cable with lockable connector
DGND
GPIO 1
GDND
GPIO 0
AI 1
Ready-to-Use ADLINK U-Test Utility
■Ready-to-Use ADLINK U-Test Utility
U-Test is a free ready-to-use testing program allowing configuration and test data acquisition
with no programming required. Easy out-of-the-box configuration and generation of simple
functions , including full data monitoring, logging and FFT analysis is easy and fast, with no
programming requirement.
No programming necessary for operation
and full function testing of ADLINK USB
DAQ/DIO
• Module stand
• Rail-mount kit
Intuitive interface for data monitoring and
logging, waveform generation, and
digital I/O control panel use as virtual
instrument
Useful analysis functions, such as direct
cursor measurement of traces and
real-time FFT analysis
Data exportable to Microsoft Excel for
offline analysis
Supports auto-recollection of configuration settings for future use
3-11 www.adlinktech.com
USB DAQ
1
PXI/PXIe
Specifications
Analog Input
General Specifications
Channels
4 (simultaneous sampling)
ADC Resolution
24 Bit
ADC type
Delta-sigma
Sampling rate
1 kS/s to 128 kS/s
±10V
2k samples per channel
Input Configuration
Input impedance
Input Signal Frequency (fin)
Flatness
20 Hz to 20 kHz
±0.01 dB
20 Hz to 46.4 kHz
±0.15 dB
• Crosstalk
Input Signal Frequency (fin)
Crosstalk
Differential or pseudo-differential
1 kHz
-102 dB
200 kΩ (between positive input and
negative input)
16.93 kΩ (Between negative input
and chassis ground)
46.4 kHz
-95 dB
Input coupling
• System noise
Mode
AI Noise
High-Resolution (< 52.734 kHz)
50µVrms
High-Speed Mode
(52.734 kHz to 128 kHz)
65µVrms
AC or DC, software selectable
Integrated
Electronic
Piezoelectric
(IEPE)
Current: 2 mA or 0 mA, software
selectable
IEPE compliance: 24V
Over-voltage
protection
±60V
Input common
mode range
±10V
Input Signal Frequency (fin)
SFDR
Trigger source
Analog or digital, software selectable
1 kHz
104 dB
Trigger mode
Post trigger, delay trigger, middle
trigger,
gated trigger, pre-trigger, post or
delay trigger with re-triggering
Offset Error (mV)
Gain Error (%)
Typical: ±0.15mV
Typical: ±0.15%
Max. ±0.3mV
Max. ±0.3%
■■ AC Dynamic Performance (typical, 25°C)
Input Signal Frequency (fin)
Dynamic range
1 kHz
100 dB
Pseudodifferential
THD+N
20 Hz to 20 kHz
-94 dB
-91 dB
20 Hz to 46.4 kHz
-89 dB
-88 dB
20 Hz to 20 kHz
-92 dB
-88 dB
20 Hz to 46.4 kHz
-85 dB
-85 dB
• CMRR
AC (20 Hz to 1 kHz)
Channels
2 programmable function I/O
Compatibility
3.3V / TTL (single-ended)
Initial status
Input (pull low)
Input voltage
Logic low: VIL = 0.8 V max;
IIL = 0.2 mA max.
Logic high: VIH = 2.0 V min.;
IIH = 0.2 mA max.
Output voltage
Logic low: VOL = 0.8 V max;
IIL = 0.2 mA max.
Logic high: VOH = 2.0 V min.;
IIH = 24 mA max.
Over-voltage
protection
-2V ~ +7V
Supporting modes
•Static digital input/output
•Pulse output, max. frequency:
4 MHz
•Frequency/Event counter, max.
frequency: 4MHz
•Digital trigger IN
•Synchronization sample clock IN
Data Transfer
Programmed I/O
60 dB
• Bandwidth
-3dB bandwidth
0.49 * sampling rate
AC cut-off frequency (-3dB)
0.4 Hz
AC cut-off frequency (-0.1dB)
2.4 Hz
■RST-20P
One pair of 20-pin removable
screw terminals
■USB-2M-L
2 M USB Type A to USB Mini-B cable
with lockable connector
4
GPIB & Bus Expansion
Differential
THD
3
Optional Accessories
Digital Input / Output
• THD, THD+N (Vin = 8.9 Vpk)
Input Signal Frequency
(fin)
■USB-2405
4-CH 24-Bit 128kS/s Dynamic Signal Acquisition
USB 2.0 Module
2
DAQ
• Dynamic Range (Vin = -60 dBFS, fs=102.4kS/s)
■■ DC accuracy (25°C)
Input
configuration
Ordering Information
• SFDR (Vin = -1 dBFS)
Programmed I/O, continuous (bulk
transfer mode)
Data Transfer
■■ I/O connector: Four BNC connectors and 4-pin removable spring terminals
■■ Operating temperature: 0 to 55°C (32 to 131˚F)
■■ Storage temperature:-20 to 70°C (-4 to 158˚F)
■■ Power requirements: 5V @ 400mA (USB bus powered)
■■ Dimensions (not including connectors and stand): 115
mm (W) x 150 mm (D) x 40 mm (H) (4.5” x 5.91” x
1.57”)
■■ Relative humidity: 5% to 95%, non-condensing
Modular Instruments
Input range
FIFO buffer size
• Flatness
Note: Function I/O shares the same I/O pins, such that only one of these modes can be selected at a time.
www.adlinktech.com 3-12
USB-2401
4-CH 24-Bit Universal Input USB DAQ Modules
Introduction
The USB-2401 is a 24-Bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring
built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including
current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels
can be programmed to measure different signal types.
The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
The USB-2401 is suitable for basic measurement applications requiring high resolution and accuracy,
laboratory research and material testing environments, and industrial temperature measurement. U-test,
a free ready-to-use testing program is included to enable operation or testing of all ADLINK USB DAQ
series functions with no programming requirement.
Pin Assignment
Features
■
■
■
■
■
■
■
■
USB 2.0 High-Speed
USB bus powered
4-CH simultaneous-sampling analog input
Built-in signal conditioning for high voltage/current/thermocouple/
RTD/strain gauge/load cell measurement
Up to 2kS/s analog input rate
Removable screw terminal on module
Lockable USB cable for secure connectivity
Ready-to-use testing application (U-Test) provided
■OS Information
• Windows XP, Windows 7/8 x64/x86
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• U-Test, DAQBench, DAQMaster
Standard Shipped Accessories
• One pair of 20-pin removable screw
terminals
• Module stand
• 2 M USB Type A to USB Mini-B
cable with lockable connector
USB-2401
GPO0
20
40
GPO1
GPI1
19
39
GPI3
GPI0
18
38
GPI2
NC
17
37
DGND
GND1
16
36
GND3
SC1-
15
35
SC3-
SC1+
14
34
SC3+
EXC1
13
33
EXC3
CI1-
12
32
CI3-
CI1+
11
31
CI3+
AI1-
10
30
AI3-
AI1+
9
29
AI3+
GND0
8
28
GND2
SC0-
7
27
SC2-
SC0+
6
26
SC2+
EXC0
5
25
EXC2
CI0-
4
24
CI2-
CI0+
3
23
CI2+
AI0-
2
22
AI2-
AI0+
1
21
AI2+
• Rail-mount kit
Ordering Information
■USB-2401
4-CH 24-Bit Universal Input USB DAQ
Optional Accessories
■RST-20P
One pair of 20-pin removable
screw terminals
■USB-2M-L
2 M USB Type A to USB Mini-B cable
with lockable connector
3-13 www.adlinktech.com
USB DAQ
1
PXI/PXIe
Specifications
USB-2401
Model Name
Analog Input
Number of channels
4 differential
Resolution
24-Bit
Measurement types
Voltage, current, thermocouple, RTD, half-bridge, full-bridge, resistance
Maximum sampling rate
2 kS/s
Mode
Voltage
Current
Thermocouple
± 25 V, ± 12.5 V, ± 2.5 V, ± 312.5 mV
Actual Range
± 25 V, ± 12.5 V, ± 2.5 V, ± 312.5 mV
± 20 mA
± 20 mA
K, J, N, R, S, B, T, E
78.125 mV
RTD (3-wire, 4-wire)
Pt 100, Pt 1000
2.5 V
Half-Bridge (120Ω, 350Ω)
Max. 30 mV/V
78.125 mV
Full-Bridge (120Ω, 350Ω)
Max. 30 mV/V
78.125 mV
2-Wire Resistance
Input coupling
FIFO size
Data Transfer
2.5 V
25 kΩ
DC
4k samples
Programmed I/O, continuous (USB bulk transfer mode)
Function I/O
Number of channels
Compatibility
4 inputs and 2 outputs
5V/TTL
Digital I/O
Support modes
3
General timer/counter: One 32-Bit; base clock 80 MHz, external to 10 MHz
PWM: One channel, modulation frequency: 0.01 Hz to 5 MHz; duty cycle: 1%-99%
Programmed I/O, continuous (USB bulk transfer mode)
DAQ
Data Transfer
General Specifications
I/O connector
Operating temperature
Storage temperature
Power requirements
Dimensions
Relative humidity
2
Modular Instruments
Input ranges
Input range or supporting type
Two 20-pin removable screw terminals
0 to 55°C (32˚F to 122˚F)
-20 to 70°C (-4˚F to 158˚F)
5V @ 400 mA (USB powered)
114 (H) x 156.5 (L) x 41 mm (W) (4.5” x 6.16” x 1.63”)
(without connector and stand)
5% to 95%, non-condensing)
Note: Function I/O shares the same I/O pins. Only one of these modes can be selected.
4
GPIB & Bus Expansion
www.adlinktech.com 3-14
USB-7230/7250
Isolated USB Digital I/O Modules
Introduction
The USB-7230/7250 USB-based digital I/O modules feature high voltage on/off control and monitoring,
and isolation voltage supported up to 2500VRMS. The USB-7230 provides 32-CH isolated digital I/O and
2-CH frequency/event counters. The USB-7250 provides 8-CH relay output (4 form C and 4 form A),
8-CH isolated DI, and 2-CH frequency/event counters.
The USB-powered USB-7230/7250 features removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
The USB-7230/7250 is suitable for industrial I/O control applications requiring high voltage and superior
protection. High isolation voltage protects against damage from accidental contact with external voltages
and eliminates troublesome ground loops. U-Test, a free ready-to-use testing program, is included to enable operation or testing of all ADLINK USB DAQ series functions with no programming requirement.
Features
■
■
■
■
■
USB 2.0, USB bus powered
Programmable digital filter removes unexpected glitches from input channels
Programmable DO/Relay initial status
Up to 2500 VRMS isolation voltage
Removable screw terminal on module
Lockable USB cable for secure connectivity
Ready-to-use testing application (U-Test) provided
Pin Assignment
USB-7230
USB-7250
VDD
20
40
DO15
NO7
20
40
GND1
DO7
19
39
DO14
COM7
19
39
CNT1
DO6
18
38
DO13
NO6
18
38
GND0
DO5
17
37
DO12
COM6
17
37
CNT0
DO4
16
36
DO11
NO5
16
36
DI7L
■Software Compatibility
DO3
15
35
DO10
COM5
15
35
DI7H
DO2
14
34
DO9
NO4
14
34
DI6L
■Software Recommendations
DO1
13
33
DO8
COM4
13
33
DI6H
DO0
12
32
IGND
NC3
12
32
DI5L
IGND
11
31
IGND
NO3
11
31
DI5H
CNT0
10
30
CNT1
COM3
10
30
DI4L
CGND
9
29
COM
NC2
9
29
DI4H
DI7
8
28
DI15
NO2
8
28
DI3L
DI6
7
27
DI14
COM2
7
27
DI3H
DI5
6
26
DI13
NC1
6
26
DI2L
DI4
5
25
DI12
NO1
5
25
DI2H
DI3
4
24
DI11
COM1
4
24
DI1L
DI2
3
23
DI10
NC0
3
23
DI1H
DI1
2
22
DI9
NO0
2
22
DI0L
DI0
1
21
DI8
COM0
1
21
DI0H
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86
• LabVIEW, MATLAB, Visual Studio.NET
• U-Test, DAQBench, DAQMaster
Standard Shipped Accessories
• One pair of 20-pin removable screw
terminals
• Module stand
• 2 M USB Type A to USB Mini-B
cable with lockable connector
• Rail-mount kit
Ordering Information
■USB-7230
2-CH isolated Digital I/O & 2-CH counter USB module
■USB-7250
8-CH relay output, 8-CH isolated DI, & 2-CH counter
USB module
3-15 www.adlinktech.com
Optional Accessories
■RST-20P
One pair of 20-pin removable
screw terminals
■USB-2M-L
2 M USB Type A to USB Mini-B cable
with lockable connector
USB DAQ
1
PXI/PXIe
Specifications
USB-7230
USB-7250
Channels
-
8 (solid-state relay, non-latching, 4-CH form C & 4-CH form A)
Max. switching power
-
60 W, 125 VA
Max. switching voltage
-
220 VDC, 250 VAC
Max. switching current
-
2A
Max. carrying current
-
2A
Max. contact rating
-
30 VDC, 2 A (Resistive)
Model Name
Relay output
2
110 VDC, 0.3 A (Resistive)
Relay on/off time
-
Operating time
Modular Instruments
125 VAC, 0.5 A (Resistive)
2 ms
Release time
1 ms
Resistance
-
75mΩ
Expected life
-
50 VDC 0.1A (resistive), 1x106
Breakdown voltage
-
1500 V surge
Optical Isolated Input
Channels
16
8
Bi-directional (non-polarity)
Polarity
VIH=5 to 24V, VIL=0 to 0.1.5V or dry contact
Logic level
Input resistance
2.4k @ 0.5W
Isolated voltage
2500VRMS (channel to system)
3
20.83ns (software programmable)
Min. pulse-width for change of state (COS) detection
Optical Isolated Frequency/Event Counter
2
Logic level
VIH=5 to 12V, VIL=0 to 0.1.5V
Event counter width
32-Bit
Max. input frequency (DC coupled)
1 MHz
Min. input frequency (DC coupled)
DAQ
Channels
0.1 Hz
Max. frequency error
0.5% (f ≦ 50kHz)
1% (50kHz < f ≦ 500kHz)
2% (500kHz < f ≦ 1MHz)
Optical Isolated Output
Channels
Output type
Supply voltage
Max. sink current
16
-
Open drain MOSFET
-
5-35VDC
-
250 mA @ 100% duty (per channel)
-
4
General Specifications
High speed USB 2.0 compatible, mini-USB connector
Data transfer
Programmed I/O
Dimensions
156.5 (L) x 114 (W) x 41.3 (H) mm (6.16” x 4.49” x 1.63”)
I/O Connector
Power requirement
GPIB & Bus Expansion
Interface
Two 20-pin removable screw-down terminals
USB power (5 V @ 400 mA)
www.adlinktech.com 3-16
PCI-9221/9222/9223
16/32-CH 16-Bit 250/500 kS/s Multi-Function DAQ Cards with Encoder Input
Specifications
Model Name
PCI-9222/9223
PCI-9221
Features
■
Supports a 32-Bit 3.3 V or 5 V PCI bus
Programmable gains for analog input: 1, 2, 4, 5, 8, 10, 20, 40 (PCI-9222/9223) 1, 5, 10, 25 (PCI-9221)
■ 2-CH 16-Bit simultaneous analog outputs, up to 1 MS/s analog output update rate (PCI-9222/9223)
■ Programmable function I/O, supporting modes:
• TTL DI and TTL DO
• 2 MHz High-Speed DIO (PCI-9222/9223 only)
• General-purpose timer/counter
• PWM outputs
• Encoder inputs
■ Dedicated 2-CH 4 MHz encoder inputs, supporting AB phase, and CW/CCW (PCI-9222/9223)
■ Dedicated DMA channels for A/D, D/A, and high-speed DIO (PCI-9222/9223)
■ External digital trigger for A/D, D/A, and high-speed DIO (PCI-9222/9223)
■ Multiple card synchronization through SSI
(System Synchronization Interface) bus (PCI-9222/9223)
■Auto-calibration
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Analog Input
Resolution
Number of channels
Maximum sampling rate
(single channel)
Programmable gain
Input range
Offset error
Gain error
FIFO buffer size
Trigger sources
Trigger mode
External conversion source
Input coupling
Overvoltage protection
Input impedance
Data Transfer
Analog Output
Number of channels
Resolution
Maximum update rate
FIFO
Output range
Output driving capacity
Slew rate
Setting time (0.1% of full scale)
Offset error
Gain error
Rising time
Falling time
Function I/O
Mode
Digital I/O
General Timer/Counter
Pulse generation
Encoder Input
Number of channels
Encoder type
General Specifications
PCI Bus
Auto-calibration
I/O Connector
Operation temperature
Storage temperature
Humidity
Power requirements
Dimensions
Terminal Boards & Cables
■DIN-68S-01 (for PCI-9222/9223)
■DIN-37D-01 (for PCI-9221)
■ACL-10568-1 (for PCI-9222/9223)
■ACL-10137-1MM (for PCI-9221)
■ACL-SSI-2/3/4 (for PCI-9222/9223)
* For more information on mating terminal board and cables, please
refer to P3-48/49.
3-17 www.adlinktech.com
PCI-9221
PCI-9222
PCI-9223
16 SE/ 8 DIFF
250 kS/s
16 Bit
16 SE/ 8 DIFF
250 kS/s
32 SE/ 16 DIFF
500 kS/s
1, 5,10, 25
±5 V, ±1 V, ±500 mV, ±200 mV
1, 2, 4, 5, 8, 10, 20, 40
1, 2, 4, 5, 8, 10, 20, 40
±10 V, ±5 V, ±2.5 V, ±2 V, ±1.25 V, ±10 V, ±5 V, ±2.5 V, ±2 V, ±1.25 V,
±1 V, ±500 mV, ±250 mV
±1 V, ±500 mV, ±250 mV
±0.7 mV typical, after calibration
±0.015% of FSR, after calibration
1 k samples
Software, external digital
Software, external digital, SSI
Post trigger
Post trigger, retrigger, gate trigger
Yes (up to 250 kS/s)
Yes (up to 250 kS/s)
Yes (up to 500 kS/s)
DC
±10 V
Continuous ±30 V
High impedance > 1 GΩ
Programmed I/O, Interrupt, Bus Mastering DMA
2 voltage outputs
16-Bit
1 MHz (simultaneous update)
512
±10 V
±5 mA
20 V/μs
2.6 μs
±1 mV
±0.01% FSR
0.67 μs
0.705 μs
1.25 kS/s (static)
±5 V
0.014 V/μs
1396 μs
±0.02% FSR
390 μs
395 μs
Digital I/O(1) , General Timer/
Counter(1),Pulse Generation(1)
8 DI/4 DO (5 V TTL level)
Two 32-Bit, Base clock: 40 MHz,
external to 10 MHz
Two PWM outputs (Modulation
frequency: 0.005 Hz to 5 MHz;
Duty cycle: 1%-99%)
Digital I/O, General Timer/Counter,Pulse Generation
16 DO (3.3 V TTL Level) / 16 DI (3.3 V or 5 V TTL Level)
Four 32-Bit, Base clock: 80 MHz, external to 10 MHz
Four PWM outputs (Modulation frequency: 0.01 Hz to 5 MHz;
Duty cycle: 1%-99%)
2(2)
CW/CCW encoder, x 1 AB phase encoder, x 2 AB phase encoder, x 4 AB phase encoder
One 37-pin D-Sub connector
0˚C to 45˚C (32˚F to 113˚F)
-20˚C to 80˚C (-4˚F to 176˚F)
+5 V 1A typical,+12 V 100mA
typical,-12 V 100mA typical
120 mm x 87 mm (4.68" x 3.39")
5 V and 3.3 V universal PCI bus
Yes
Two 68-pin SCSI-VHDCI female
0˚C to 55˚C (32˚F to 131˚F)
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95% non-condensing
+5 V 1.2 A typical, +12 V 760 mA typical, -12 V 50 mA typical
175 mm x 107 mm (6.82" x 4.17")(not including connectors)
Note:
(1) The function I/O and encoder inputs share the same I/O pins of the PCI-9221. Only one of these modes can be selected.
(2) Dedicated
Ordering Information
■PCI-9221
2-CH 16-Bit 250 kS/s Multi-Function DAQ
Card with Encoder Input
■PCI-9222
16-CH 16-Bit 250 kS/s Multi-Function DAQ
Card with Encoder Input
■PCI-9223
32-CH 16-Bit 500 kS/s Multi-Function DAQ
Card with Encoder Input
High-Performance DAQ
PXI/DAQ/DAQe-2000 Series
4-CH 14/16-Bit Up to 2 MS/s Simultaneous-Sampling DAQ Cards
1
PXI/PXIe
Ordering Information / Quick Selection Guide
Model Name
Analog Input
No. of
channels
PXI-2010
Resolution
DIO
Timer/Counter
Sampling
rate
Input range
No. of
channels
Resolution
Analog Output
Update rate
No. of channels
No. of channels
PXI/DAQ/DAQe-2010
4-CH DI
14 Bit
2 MS/s
±1.25 V to ±10 V
2
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
PXI/DAQ/DAQe-2005
4-CH DI
16 Bit
500 kS/s
±1.25 V to ±10 V
2
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
PXI/DAQ/DAQe-2006
4-CH DI
16 Bit
250 kS/s
±1.25 V to ±10 V
2
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
Specifications
Model Name
DAQe-2010
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Terminal Boards & Cables
Connector
Operating temperature
Storage temperature
Humidity
Power requirements
PXI/DAQ/DAQe-2006
14 Bit
16 Bit, no missing codes
16 Bit, no missing codes
4 simultaneous-sampling channels with differential input
2 MS/s
500 kS/s
250 kS/s
1, 2, 4, 8
±10 V, ±5 V, ±2.5 V, ±1.25 V
0-10 V, 0-5 V, 0-2.5 V, 0-1.25 V
±3 mV
2 mV
±1 mV
±0.1% of FSR
±0.04% of FSR
±0.03% of FSR
DC
Power on: Continuous ±35 V, Power off: Continuous ±15 V
1 GΩ/100 pF
Software, external digital/analog trigger, SSI bus
Pre-trigger, post-trigger, middle-trigger, delay-trigger, and repeated trigger
8 k samples
512 samples
512 samples
Polling, scatter-gather DMA
2 voltage outputs
12 Bit
0-10 V, ±10 V, 0-AOEXTREF, ±AOEXTREF
1 μs
20 V/μs
3 μs to ±0.5 LSB accuracy
±3mV
±1mV
±1mV
±0.05% of max. output
±0.04% of max. output
±0.04% of max. output
5 mA
Any passive load, up to 1500 pF
Software, external digital/analog trigger, SSI bus
Post-trigger, delay-trigger, and repeated trigger
2 k samples
Programmed I/O, scatter-gather DMA
8255 24-Bit programmable input/output
5 V/TTL
Programmed I/O
2
3
4
2
16 Bit
5 V/TTL
40 MHz , external clock up to 10 MHz
Yes (+5 V, ±2 ppm/˚C)
160 mm x 100 mm (not including connectors) (PXI-2000 series)
175 mm x 107 mm (not including connectors) (DAQ-2000 series)
168 mm x 107 mm (not including connectors) (DAQe-2000 series)
68-pin VHDCI-type female
0˚C to 55˚C (32˚F to 131˚F )
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95%, non-condensing
+5 V 1.82 A typical (PXI/DAQ-2010) +5 V 2.04 A typical (PXI/DAQ-2005) +5 V 1.82 A typical (DAQ-2006)
+3.3 V 1.02 A, +12 V 0.67 A
+3.3 V 1.03 A, +12 V 0.75 A
+3.3 V 1.246 A, +12 V 0.448 A
typical (DAQe-2006)
typical (DAQe-2005)
typical (DAQe-2010)
■DIN-68S-01
■ACL-10568-1
■ACL-SSI-2/3/4
* For more information on mating terminal board and cables, please
refer to P3-48/49.
www.adlinktech.com 3-18
GPIB & Bus Expansion
Supports a 32-Bit 3.3 V or 5 V PCI bus (DAQ-2000 series)
x1 lane PCI Express® Interface (DAQe-2000 series)
■ PXI specification Rev. 2.2 compliant (PXI-2000 series)
■ 4-CH differential analog inputs
■ Bipolar or unipolar analog input ranges
■ Programmable gains of x1, x2, x4, x8
■ Scatter-gather DMA for both analog inputs and outputs
■ 2-CH 12-Bit multiplying analog outputs with waveform generation
■ 24-CH TTL digital input/output
■ 2-CH 16-Bit general-purpose timer/counter
■ Analog and digital triggering
■ Fully auto calibration
■ Multiple cards synchronization through SSI (System
Synchronization Interface) bus or PXI trigger bus
■
PXI/DAQ/DAQe-2005
DAQ
Features
PXI/DAQ/DAQe-2010
Modular Instruments
DAQ-2010
Analog Input
Resolution
Number of channels
Maximum sampling rate
Programmable gain
Bipolar input ranges
Unipolar input ranges
Offset error
Gain error
Input Coupling
Overvoltage protection
Input Impedance
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Analog Output
Number of channels
Resolution
Output ranges
Maximum update rate
Slew rate
Settling time
Offset error
Gain error
Driving capacity
Stabililty
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Digital I/O
Number of channels
Compatibility
Data transfers
Timer/Counter
Number of channels
Resolution
Compatibility
Base clock available
General Specifications
Auto Calibration
Dimensions
PXI-2020/2022
8/16-CH 16-Bit 250 KS/s Simultaneous Sampling DAQ Cards
Ordering Information / Quick Selection Guide
Analog Input
Model
Name
PXI-2020
PXI-2022
PXI-2022
No. of channels Resolution Sampling rate
8-CH DI
16-CH DI
■
Supports 3.3 V and 5 V PCI signaling
■
PXI specification Rev 2.2 compliant
■
8/16-CH differential analog inputs (PXI-2020/PXI-2022)
■
Bipolar analog input
■
Programmable gains of x1, x4
■
Scatter gather DMA transfer for AI continuously
data acquisition
■
4-CH TTL digital input/output
■
3U EuroCard form factor
■
2-CH 32-Bit general purpose timer/counters
■
Digital triggering
■
Fully auto calibration
■
Multiple cards synchronization through PXI trigger bus
■
Onboard 8 K-sample (16 KB) memory for data storage
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Terminal Boards & Cables
■DIN-68S-01
■ACL-10568-1
* For more information on mating terminal board and cables, please
refer to P3-48/49.
Accessories
■SMB-SMB-1M
■SMB-BNC-1M
3-19 www.adlinktech.com
250 kS/s
250 kS/s
Analog Output
DIO
Timer/Counter
No. of channels Resolution Output range
No. of channels
No. of channels
4 DI/4 DO
4 DI/4 DO
2-CH, 32-Bit
2-CH, 32-Bit
± 2.5 V to ± 10 V
± 2.5 V to ± 10 V
-
-
-
Specifications
Model Name
Features
16 Bit
16 Bit
Input range
Analog Input
Resolution
Number of Channels
Input Impedance
Input Coupling
Bipolar Input Signal Range
Programmable gain
Overvoltage Protection
Max Sampling Rate
Data FIFO Size
DNL (gain =1)
INL (gain =1)
Offset Error (gain =1)
Gain Error (gain =1)
Data Transfer
Digital I/O
Number of Channel
Compatibility
Input Logic Levels
Output Logic Levels
Output Driving Capacity
Power-on State
Data Transfer
General Specifications
Auto Calibration
Dimensions
Connector
Operating Environment
Storage Environment
PXI-2020
PXI-2022
16 Bit
8 differential channels
16 differential channels
1 GΩ/pF
DC
± 10 V, ± 2.5 V
1, 4
Power on: ±30 V continuous
Power off: ±30 V continuous
250 KS/s
8 K-sample (16 KB)
±0.8 LSB
±1.5 LSB (typical), ±3.0 LSB (MAX)
0.6 mV (typical)
0.05% of input
16 differential channels
4 input/output
TTL / CMOS
Input low voltage: 0.8 V (max)
Input high voltage: 2.0 V(min)
Output low voltage: 0.4 V (max)
Output high voltage: 2.8 V (min)
±24 mA
Input, pull-low with 10 KΩ resistor
Polling mode
Yes (+5 V, ±3 ppm/˚C)
Single 3U PXI module, 100 mm x 160 mm (not including connector)
ACL-10568-1, 68-pin VHDCI-type female
Ambient temperature: 0˚C to 55˚C (32˚F to 131˚F)
Relative humidity: 10% to 90% non-condensing
Ambient temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative humidity: 5% to 95% non-condensing
High-Performance DAQ
PXI/DAQ/DAQe-2208
96-CH 12-Bit 3 MS/s Ultra High-Density Analog Input Cards
1
PXI/PXIe
Ordering Information / Quick Selection Guide
Model Name
PXI-2208
PXI/DAQ/DAQe-2208
DIO
Timer/Counter
No. of
channels
Resolution
Analog Input
Sampling
rate
Input range
No. of
channels
Resolution
Analog Output
Update rate
No. of channels
No. of channels
48 DI/96 SE
12 Bit
3 MS/s
±0.05 V to ±10 V
-
-
-
24-Bit 8255 PIO
-
Specifications
Model Name
DAQe-2208
■
■
■
■
■
■
■
■
■
■
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
Connector
Operating temperature
Storage temperature
Humidity
Power requirements
24-CH 8255 programmable input/output
5 V/TTL
Programmed I/O
4
Terminal Boards & Cables
■DIN-68S-01
■ACL-10568-1
■ACL-SSI-2/3/4
* For more information on mating terminal board and cables,
please refer to P3-48/49.
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
3
Yes (+5 V, ±2 ppm/˚C)
160 mm x 100 mm (not including connectors) (PXI-2208)
175 mm x 107 mm (not including connectors) (DAQ-2208)
168 mm x 107 mm (not including connectors) (DAQe-2208)
68-pin VHDCI female x 2
0˚C to 55˚C (32˚F to 131˚F)
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95%, non-condensing
+5 V 0.95 A typical (PXI/DAQ-2208)
+3.3 V 0.81 A, +12 V 0.568 A typical (DAQe-2208)
■Software Compatibility
2
GPIB & Bus Expansion
■
Supports a 32-Bit 3.3 V or 5 V PCI bus (DAQ-2208)
x1 lane PCI Express® Interface (DAQe-2208)
PXI Specification Rev. 2.2 compliant (PXI-2208)
96-CH single-ended or 48-CH differential analog inputs
Onboard 1 k-sample A/D FIFO
Bipolar or unipolar analog input ranges
Programmable gains of x1, x2, x4, x5, x8, x10, x20, x40, x50, x200
1024-configuration channel gain queue
Scatter-gather DMA for analog inputs
24-CH TTL digital input/output
Analog and digital triggering
Fully auto calibration
Multiple cards synchronization through SSI
(System Synchronization Interface) bus or PXI trigger bus
12 Bit, no missing codes
96 single-ended or 48 differential
1024
3 MS/s
1, 2, 4, 5, 8, 10, 20, 40, 50, 200
±10 V, ±5 V, ±2.5 V, ±2 V, ±1.25 V, ±1 V, ±0.5 V, ±0.25 V, ±0.2 V, ±0.05 V
0-10 V, 0-5 V, 0-4 V, 0-2.5 V, 0-1 V, 0-0.5 V, 0-0.4 V, 0-0.1 V
±2 mV
±0.06% of FSR
DC
Power on: Continuous ±30 V, Power off: Continuous ±15 V
1 GΩ/100 pF
Software, external digital/analog trigger, SSI bus
Pre-trigger, post-trigger, middle-trigger, delay-trigger, and repeated trigger
1 k samples
Polling, scatter-gather DMA
DAQ
Features
PXI/DAQ/DAQe-2208
Modular Instruments
DAQ-2208
Analog Input
Resolution
Number of channels
Channel gain queue size
Maximum sampling rate
Programmable gain
Bipolar input ranges
Unipolar input ranges
Offset error
Gain error
Input Coupling
Overvoltage protection
Input Impedance
Trigger sources
Trigger modes
FIFO buffer size
Data Transfers
Digital I/O
Number of channels
Compatibility
Data transfers
General Specifications
Auto Calibration
Dimensions
• AD-Logger, DAQBench, DAQMaster
www.adlinktech.com 3-20
PXI/DAQ/DAQe-2200 Series
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ Cards
Ordering Information / Quick Selection Guide
Model Name
PXI-2204
Analog Input
No. of
channels
PXI/DAQ/DAQe-2204
32 DI/64 SE
PXI/DAQ/DAQe-2205
PXI/DAQ/DAQe-2206
Analog Output
DIO
Timer/Counter
Update rate
No. of channels
No. of channels
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
Input range
No. of
channels
Resolution
±0.05 V to ±10 V
2
12 Bit
500 kS/s
±1.25 V to ±10 V
2
250 kS/s
±1.25 V to ±10 V
2
Resolution
Sampling
rate
12 Bit
3 MS/s
32 DI/64 SE
16 Bit
32 DI/64 SE
16 Bit
Specifications
Model Name
DAQ-2204
DAQe-2204
Features
■
■
Supports a 32-Bit 3.3 V or 5 V PCI bus (DAQ-2200 series)
x1 lane PCI Express® Interface (DAQe-2200 series)
PXI specification Rev 2.2 compliant (PXI-2200 series)
64-CH single-ended or 32-CH differential analog inputs
Onboard 1 k-sample A/D FIFO
Bipolar or unipolar analog input ranges
Programmable gains:
• x1, x2, x4, x5, x8, x10, x20, x40, x50, x200 (DAQ/DAQe-2204)
■
■
■
■
■
• x1, x2, x4, x8 (DAQ/DAQe-2205 & DAQ/DAQe-2206)
512-configuration channel gain queue
■ Scatter-gather DMA for both analog inputs and outputs
■ 2-CH 12-Bit multiplying analog outputs with waveform generation
■ Onboard 1 k-sample D/A FIFO
■ 24-CH TTL digital input/output
■ 2-CH 16-Bit general-purpose timer/counter
■ Analog and digital triggering
■ Fully auto calibration
■ Multiple cards synchronization through SSI (System
Synchronization Interface) bus or PXI trigger bus
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
Analog Input
Resolution
Number of channels
Channel gain queue size
Maximum sampling rate
Programmable gain
Bipolar input ranges
Unipolar input ranges
Offset error
Gain error
Input coupling
Overvoltage protection
Input impedance
CMRR (gain = 1)
Settling time
-3 dB small signal bandwidth
(@Bipolar +/-10V Gain=1)
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Analog Output
Number of channels
Resolution
Output ranges
Maximum update rate
Slew rate
Settling time
Offset error
Gain error
Driving capacity
Stability
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Digital I/O
Number of channels
Compatibility
Data transfers
General-Purpose Timer/Counter
Number of channels
Resolution
Base clock available
General Specifications
Auto Calibration
Dimensions
Connector
Operating temperature
Storage temperature
Humidity
Power requirements
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-21 www.adlinktech.com
PXI/DAQ/DAQe-2204
PXI/DAQ/DAQe-2205
PXI/DAQ/DAQe-2206
12 Bit, no missing codes
16 Bit, no missing codes
64 single-ended or 32 differential (software selectable per channel)
512
3 MS/s
500 kS/s
250 kS/s
1, 2, 4, 5, 8, 10, 20, 40, 50, 200
1, 2, 4, 8
Max. : ±10 V, Min. : ±0.05 V±10 V, ±5 V, ±2.5 V, ±1.25 V±10 V, ±5 V, ±2.5 V, ±1.25 V
Max. : 0-10 V, Min. : 0-0.1 V0-10 V, 0-5 V, 0-2.5 V, 0-1.25 V0-10 V, 0-5 V, 0-2.5 V, 0-1.25 V
±2 mV
±1 mV
±2 mV
±0.06% of FSR
±0.08% of FSR
±0.06% of FSR
DC
Power on: Continuous ±30 V, Power off: Continuous ±15 V
1 GΩ/100 pF
90 dB
83 dB
1 μs to 0.1% error
2 μs to 0.1% error
4 μs to 0.01% error
2 MHz
850kHz
600 kHz
Software, external digital/analog trigger, SSI bus
Pre-trigger, post-trigger, middle-trigger, delay-trigger, and repeated trigger
1 k samples
Polling, scatter-gather DMA
2 voltage outputs
12 Bit
0-10 V, ±10 V, 0-AOEXTREF, ±AOEXTREF
1 μs
20 V/μs
3 μs to ±0.5 LSB accuracy
±1 mV
±2 mV
±1 mV
±0.02% of max. output
±0.04% of max. output
±0.02% of max. output
±5 mA
Any passive load, up to 1500 pF
Software, external digital/analog trigger, SSI bus
Post-trigger, delay-trigger, and repeated trigger
1 k samples
Programmed I/O, scatter-gather DMA
24-CH 8255 programmable input/output
5 V/TTL
Programmed I/O
2
16-Bit
40 MHz, external clock up to 10 MHz
Yes (+5 V, ±2 ppm/˚C)
160 mm x 100 mm (6.24" x 3.9") (not including connectors) (PXI-2200 series)
175 mm x 107 mm (6.82" x 4.17") (not including connectors) (DAQ-2200 series)
168 mm x 107 mm (6.55" x 4.17") (not including connectors) (DAQe-2200 series)
68-pin VHDCI female x 2
0˚C to 55˚C (32˚F to 131˚F)
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95%, non-condensing
+5 V 1.2 A typical
+5 V 1.2 A typical
+5 V 1.3 A typical
(PXI/DAQ-2206)
(PXI/DAQ-2205)
(PXI/DAQ-2204)
+3.3 V 0.756 A, +12 V 0.584 A
+3.3 V 0.81 A, +12 V 0.568 A
+3.3 V 0.9 A, +12 V 0.564 A
typical (DAQe-2206)
typical (DAQe-2205)
typical (DAQe-2204)
Terminal Boards & Cables
■DIN-68S-01
■ACL-SSI-2/3/4
■ACL-10568-1
* For more information on mating terminal board and cables, please
refer to P3-48/49.
High-Performance DAQ
PXI/DAQ/DAQe-2500 Series
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ Cards
1
PXI/PXIe
Ordering Information / Quick Selection Guide
Model Name
Analog Output
No. of
channels
PXI-2502
Resolution
Update
rate
Analog Input
No. of
channels
Output range
Resolution
Sampling rate
Input range
DIO
Timer/Counter
No. of channels
No. of channels
PXI/DAQ/DAQe-2501
4
12 Bit
1 MS/s
±10 V, 0 to 10 V
8
14 Bit
400 kS/s
±10 V or 0 to 10 V
24-CH 8255 PIO
2-CH, 16-Bit
PXI/DAQ/DAQe-2502
8
12 Bit
1 MS/s
±10 V, 0 to 10 V
4
14 Bit
400 kS/s
±10 V or 0 to 10 V
24-CH 8255 PIO
2-CH, 16-Bit
Specifications
Model Name
DAQe-2502
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Connector
Operating temperature
Storage temperature
Humidity
Power requirements
4 voltage outputs
8 voltage outputs
12 Bit
0-10 V, ±10 V, 0-AOEXTREF, ±AOEXTREF
1 MS/s
20 V/μs
3 μs to ±0.5 LSB accuracy
±8 mV
±0.04% of max. output
±5 mA
Any passive load, up to 1500 pF
Software, external digital/analog trigger, SSI bus
Post-trigger, delay-trigger, and repeated trigger
8 k samples
16 k samples
Programmed I/O, scatter-gather DMA
14 Bit, no missing codes
8 single-ended
4 single-ended
400 kS/s
1
±10 V
0-10 V
±4 mV
±0.1% of FSR
DC
Power on: Continuous ±30 V, Power off: Continuous ±15 V
1 GΩ/6 pF
Software, external digital/analog trigger, SSI bus
Post-trigger, delay-trigger, and repeated trigger
2 k samples
Polling, scatter-gather DMA
24-CH 8255 programmable input/output
5 V/TTL
Programmed I/O
2
3
4
2
16 Bit
5 V/TTL
40 MHz, external clock up to 10 MHz
Yes (+5 V, ±2 ppm/˚C)
160 mm x 100 mm (6.24" x 3.9") (not including connectors) (PXI-2500 series)
175 mm x 107 mm (6.82" x 4.17") (not including connectors) (DAQ-2500 series)
168 mm x 107 mm (6.55” x 4.17") (not including connectors) (DAQe-2500 series)
68-pin VHDCI female
0˚C to 55˚C (32˚F to 131˚F)
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95%, non-condensing
+5 V 2.12 A typical (PXI/DAQ-2502)
+5 V 1.6 A typical (PXI/DAQ-2501)
+3.3 V 0.89 A, +12 V 0.76 A typical
+3.3 V 0.78 A, +12 V 0.66 A typical
(DAQe-2502)
(DAQe-2501)
Terminal Boards & Cables
■DIN-68S-01
■ACL-10568-1
■ACL-SSI-2/3/4
* For more information on mating terminal board and cables,
please refer to P3-48/49.
www.adlinktech.com 3-22
GPIB & Bus Expansion
Supports a 32-Bit 3.3 V or 5 V PCI bus (DAQ-2500 series)
PXI specification Rev 2.2 compliant (PXI-2500 series)
■ x1 lane PCI Express® Interface (DAQe-2500 series)
■ Hardware-based arbitrary waveform generation
■ Onboard 8 k-sample D/A FIFO (PXI/DAQ/DAQe-2501)
■ Onboard 16 k-sample D/A FIFO (PXI/DAQ/DAQe-2502)
■ Programmable bipolar or unipolar analog output ranges / internal or external reference sources on per channel basis
■ 8-CH 400 kS/s 14-Bit single-ended analog inputs (PXI/
DAQ/DAQe-2501) ; 4-CH 400 kS/s 14-Bit single-ended analog inputs (PXI/DAQ/DAQe-2502)
■ Onboard 2 k-sample A/D FIFO
■ Bipolar or unipolar analog input ranges
■ Scatter-gather DMA for both analog inputs and outputs
■ 24-CH TTL digital input/output
■ 2-CH 16-Bit general-purpose timer/counter
■ Analog & digital triggering
■ Fully auto-calibration
■ Multiple cards synchronization through SSI
(System Synchronization Interface) bus or PXI trigger bus
■
PXI/DAQ/DAQe-2502
DAQ
Features
PXI/DAQ/DAQe-2501
Modular Instruments
DAQ-2502
Analog Output
Number of channels
Resolution
Output ranges
Maximum update rate
Slew rate
Settling time
Offset error
Gain error
Driving capacity
Stability
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Analog Input
Resolution
Number of channels
Maximum sampling rate
Gain
Bipolar input ranges
Unipolar input ranges
Offset error
Gain error
Input coupling
Overvoltage protection
Input impedance
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Digital I/O
Number of channels
Compatibility
Data transfers
Timer/Counter
Number of channels
Resolution
Compatibility
Base clock available
General Specifications
Auto Calibration
Dimensions
DAQ/DAQe-2213/2214
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ Cards
Ordering Information / Quick Selection Guide
Model Name
DAQ-2213 / 2214
Analog Input
Analog Output
No. of
channels
Resolution
Sampling rate
Input range
DAQ/DAQe-2213
8 DI/16 SE
16 Bit
250 kS/s
±1.25 V to ±10 V
-
DAQ/DAQe-2214
8 DI/16 SE
16 Bit
250 kS/s
±1.25 V to ±10 V
2
DAQ-2213/2214
No. of
channels
DIO
Timer/Counter
Sampling rate
No. of channels
No. of channels
-
-
24-CH 8255 PIO
2-CH, 16-Bit
12 Bit
1 MS/s
24-CH 8255 PIO
2-CH, 16-Bit
Resolution
Specifications
Model Name
DAQe-2213 / 2214
Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 3.3 V or 5 V PCI bus
(DAQ-2213, DAQ-2214)
x1 lane PCI Express® Interface (DAQe-2213, DAQe-2214)
Onboard 1 k-sample A/D FIFO
Bipolar or unipolar analog input ranges
Programmable gains: x1, x2, x4, x8
512-configuration channel gain queue
Scatter-gather DMA
2-CH 12-Bit multiplying analog outputs with waveform generation (DAQ/DAQe-2214)
Onboard 1 k-sample D/A FIFO (DAQ-2214, DAQe-2214)
24-CH TTL digital input/output
2-CH 16-Bit general-purpose timer/counter
Analog and digital triggering
Fully auto calibration
Multiple cards synchronization through SSI (System Synchronization Interface) bus
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Terminal Boards & Cables
■DIN-68S-01
■ACL-10568-1
■ACL-SSI-2/3/4 (for DAQ/DAQe-2214)
* For more information on mating terminal board and cables,
please refer to P3-48/49.
3-23 www.adlinktech.com
Analog Input
Resolution
Number of channels
Channel gain queue size
Maximum update rate
Programmable gain
Bipolar input ranges
Unipolar input ranges
Offset error
Gain error
Input coupling
Overvoltage protection
Input impedance
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Analog Output
Number of channels
Resolution
Output ranges
Maximum update rate
Slew rate
Settling time
Offset error
Gain error
Driving capacity
Stability
Trigger sources
Trigger modes
FIFO buffer size
Data transfers
Digital I/O
Number of channels
Compatibility
Data transfers
General-Purpose Timer/Counter
Number of channels
Resolution
Compatibility
Base clock available
General Specifications
Auto Calibration
Dimensions
Connector
Operating temperature
Storage temperature
Humidity
Power requirements
DAQ/DAQe-2213
DAQ/DAQe-2214
16 Bit, no missing codes
16 single-ended or 8 differential (software selectable per channel)
512
250 kS/s
1, 2, 4, 8
±10 V, ±5 V, ±2.5 V, ±1.25 V
0-10 V, 0-5 V, 0-2.5 V, 0-1.25 V
±1 mV
±0.06% of FSR
DC
Power on: Continuous ±30 V, Power off: Continuous ±15 V
1 GΩ /100 pF
Software, external digital/analog trigger, SSI bus
Pre-trigger, post-trigger, middle-trigger, delay-trigger, and repeated trigger
1 k samples
Polling, scatter-gather DMA
-
2 voltage outputs
12 Bit
0-10 V, ±10 V, 0-AOEXTREF, ±AOEXTREF
1 μs
20 V / μs
3 μs to ±0.5 LSB accuracy
±2 mV
±0.04% of max. output
±5 mA
Any passive load, up to 1500 pF
Software, external digital/analog trigger, SSI bus
Post-trigger, delay-trigger, and repeated trigger
1 k samples
Programmed I/O, scatter-gather DMA
24-CH 8255 programmable input/output
5 V/TTL
Programmed I/O
2
16 Bit
5 V/TTL
40 MHz, external clock up to 10 MHz
Yes (+5 V, ±2 ppm/˚C)
175 mm x 107 mm (6.82" x 4.17") (not including connectors) (DAQ-2213/2214)
168 mm x 107 mm (6.55” x 4.17") (not including connectors) (DAQe-2213/2214)
68-pin VHDCI female x 2
0˚C to 55˚C (32˚F to 131˚F)
-20˚C to 70˚C (-4˚F to 158˚F)
5 to 95%, non-condensing
+5 V 1.2 A typical (DAQ-2213)
+5 V 1.2 A typical (DAQ-2214)
+3.3 V 0.84 A, +12 V 0.604 A typical (DAQe-2213)
+3.3 V 0.77 A, +12 V 0.572 A typical (DAQe-2214)
General-Purpose DAQ
PCI-9114 Series
32-CH 16-Bit Up to 250 kS/s Multi-Function DAQ Cards
1
Analog Input
■ Number of channels: 32 single-ended or 16 differential
■ Resolution: 16 Bit
■ Conversion time:
· 10 μs (PCI-9114DG)
· 4 μs (PCI-9114A-DG & PCI-9114A-HG)
■ Maximum sampling rate
Device
Sampling rate
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
250 kS/s
Input ranges (software programmable)
Device
PCI-9114DG
PCI-9114A-DG
PCI-9114A-HG
■
Gain
1
2
4
8
1
10
100
Input Range
±10 V
±5 V
±2.5 V
±1.25 V
±10 V
±1 V
±0.1 V
Gain
1
2,4
8
1, 10
100
Input Range
0.01% of FSR ± 1 LSB
0.02% of FSR ± 1 LSB
0.04% of FSR ± 1 LSB
0.01% of FSR ± 1 LSB
0.02% of FSR ± 1 LSB
Accuracy
Device
PCI-9114DG
PCI-9114A-DG
PCI-9114A-HG
■ Input coupling: DC
■ Overvoltage protection: continuous ±35 V
■ Input impedance: 1 GΩ
■ Trigger modes: software, pacer, and external trigger (5 V/TTL compatible)
■ FIFO buffer size: 1 k samples
■ Data transfers: polling, interrupt
+5 V
600 mA typical
+12 V
100 mA typical
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
Terminal Boards & Cables
■DIN-37D-01*
Terminal Board with One 37-pin D-sub Connector and DIN-Rail Mounting
■DIN-20P-01*
Terminal Board with One 20-pin Ribbon Connector and DIN-Rail Mounting
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACLD-9188-01*
General-Purpose Terminal Board with Two 20-
pin Ribbon Connectors and One 37-pin D-sub Connector
3
* Cables are not included. For information on mating cables,
refer to P3-48/49.
Ordering Information
■PCI-9114DG
32-CH 16-Bit 100 kS/s Normal-Gain Multi-Function DAQ Card
■PCI-9114A-DG
32-CH 16-Bit 250 kS/s Normal-Gain Multi-Function DAQ Card
■PCI-9114A-HG
32-CH 16-Bit 250 kS/s High-Gain Multi-Function DAQ Card
Isolated Digital Output
■ Number of channels: 16
■ Output type: open emitter Darlington transistors
■ Sink current
· 350 mA for one channel @ 100% duty
· 260 mA for all channels @ 10% duty
■ Power dissipation: Max. 1.47 W per chip (8 DO channels)
■ Supply voltage: 5-35 V
■ Isolation voltage: 2500 VRMS
■ Data transfers: programmed I/O
2
4
GPIB & Bus Expansion
Isolated Digital Input
■ Number of channels: 16
■ Maximum input range: 24 V, non-polarity
■ Digital logic levels
- 0 - 24 V, non-polarity
- Input high voltage: 5 - 24 V
- Input low voltage: 0 - 1.5 V
■ Input resistance: 2.4 KΩ @ 0.5 W
■ Isolation voltage: 2500 VRMS
■ Data transfers: programmed I/O
General Specifications
■ I/O connector
· 37-pin D-sub female
· 20-pin ribbon male x 2
■ Operating temperature: 0˚C to 55˚C (32˚F to 131˚F)
■ Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
DAQ
Supports a 32-Bit 5 V PCI bus
■ 16-Bit A/D resolution
■ Up to 100 kS/s sampling rate (PCI-9114DG)
■ Up to 250 kS/s sampling rate (PCI-9114A-DG and
PCI-9114A-HG)
■ 32-CH single-ended or 16-CH differential analog inputs
■ Bipolar or unipolar analog input ranges
■ Onboard 1 k-sample A/D FIFO
■ Programmable gains:
• x1, x2, x4, x8 (PCI-9114DG and PCI-9114A-DG)
• x1, x10, x100 (PCI-9114A-HG)
■ Automatic analog inputs scanning
■ 16-CH isolated digital inputs and 16-CH isolated digital outputs
■ 2500 VRMS optical isolation for digital inputs and outputs
■ 1-CH 16-Bit general-purpose timer/counter
■ +12 V and -12 V power available on the 37-pin D-sub connector
■ Onboard resettable fuses for power output protection
■ Compact, half-size PCB
■
■
100 kS/s
General-Purpose Timer/Counter
■ Number of channels: 1
■ Resolution: 16 Bit
■ Compatibility: 5 V/TTL
■ Base clock available: 2 MHz, external clock to 2 MHz
Modular Instruments
Features
PCI-9114DG
PCI-9114A-DG
PCI-9114A-HG
PXI/PXIe
Specifications
Power Output
■ Output voltage: +12 V and -12 V
■ Resettable fuse protection: 500 mA
www.adlinktech.com 3-24
PCI-9111 Series
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
Terminal Boards & Cables
Specifications
Analog Input
■ Number of channels: 16 single-ended
■ Resolution
· 12 Bit (PCI-9111DG)
· 16 Bit (PCI-9111HR)
■ Conversion time: 8 μs
■ Maximum sampling rate: 100 kS/s
■ Input signal ranges (software programmable)
Gain
1
2
4
8
16
Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 5 V PCI bus
12-Bit A/D resolution (PCI-9111DG)
16-Bit A/D resolution (PCI-9111HR)
16-CH single-ended analog inputs
Up to 100 kS/s sampling rate
Onboard 1 k-sample A/D FIFO
Programmable gains of x1, x2, x4, x8, x16
Bipolar analog input ranges
Onboard low-pass filtering capability for analog inputs
Automatic analog inputs scanning
One 12-Bit multiplying analog outputs
16-CH TTL digital inputs and 16-CH TTL digital outputs
4-CH TTL extended digital inputs and 4-CH TTL
extended digital outputs
Compact, half-size PCB
■OS Information
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
■
Accuracy
Gain
Accuracy
1, 2
0.01% of FSR ± 1 LSB
4, 8
0.02% of FSR ± 1 LSB
16
0.04% of FSR ± 1 LSB
■
Input coupling: DC
■ Overvoltage protection: continuous ±35 V
■ Input impedance: 10 MΩ
■ Trigger modes: software, pacer, and external trigger
(5 V/TTL compatible)
■ FIFO buffer size: 1 k samples
■
Data transfers: polling, interrupt
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
Input Range
Bipolar
±10 V
±5 V
±2.5 V
±1.25 V
±0.625 V
Analog Output
■
Number of channels: 1 voltage output (NO s)
Resolution: 12 Bit
■ Output ranges (jumper selectable)
■
• AD-Logger, DAQBench, DAQMaster
Output Range
Bipolar
±10 V
Unipolar
0 to 10 V
■
Output driving capacity: ±5 mA max
Settling time: 30 μs
■ Data transfers: programmed I/O
■
Digital I/O
■
Number of channels: 16 inputs and 16 outputs
Compatibility: 5 V/TTL
■ Data transfers: programmed I/O
■
General Specifications
■ I/O connector
· 37-pin D-sub female
· 20-pin ribbon male x 2
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
Device
PCI-9111DG
+5 V
570 mA typical
PCI-9111HR
570 mA typical
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
3-25 www.adlinktech.com
■DIN-37D-01*
Terminal Board with One 37-pin D-sub Connector and DIN-Rail Mounting
■DIN-20P-01*
Terminal Board with One 20-pin Ribbon Connector
and DIN-Rail Mounting
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACLD-9188-01*
General-Purpose Terminal Board with Two 20-pin
Ribbon Connectors and One 37-pin D-sub Connector
■ACLD-9182A-01*
Terminal Board with 16-CH Isolated Digital Inputs
■ACLD-9185-01*
Terminal Board with 16-CH Relay Outputs
* Cables are not included. For information on mating cables, refer to P3-48/49.
Ordering Information
■PCI-9111DG
16-CH 12-Bit 100 kS/s Low-Cost Multi-Function DAQ Card
■PCI-9111HR
16-CH 16-Bit 100 kS/s Low-Cost Multi-Function DAQ Card
General-Purpose DAQ
PCI-9112
16-CH 12-Bit 110 kS/s Multi-Function DAQ Card
CompactPCI
Analog Input
■ Number of channels: 16 single-ended or 8 differential
■ Resolution: 12 Bit
■ Conversion time: 8 μs
■ Maximum sampling rate: 110 kS/s
■ Input signal ranges
Gain
PCI-9112
■
■
■
■
■
■
■
■
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
■
• AD-Logger, DAQBench, DAQMaster
Accuracy
Gain
Accuracy
0.5, 1
0.01% of FSR ± 1 LSB
2, 4
0.02% of FSR ± 1 LSB
8
0.04% of FSR ± 1 LSB
■ Input coupling: DC
■ Overvoltage protection: continuous ±35 V
■ Input impedance: 1 GΩ
■ Trigger modes: software
■ Data transfers:
programmed I/O, interrupt, bus-mastering DMA
Analog Output
■ Number of channels: 2 voltage outputs
■ Resolution: 12 Bit
■ Output ranges (software programmable)
Output Range
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
Unipolar
0 to 10 V, 0 to 5 V, 0 to EXTREF
■
Output driving capacity: ±5 mA max
■ Settling time: 30 μs to 0.5 LSB
■ Data transfers: programmed I/O
Digital I/O
■ Number of channels: 16 inputs and 16 outputs
■ Compatibility: 5 V/TTL
■ Data transfers: programmed I/O
General-Purpose Timer/Counter
■ Number of channels: 1
■ Resolution: 16 Bit
■ Compatibility: 5 V/TTL
■ Base clock available: 2 MHz, external clock to 10 MHz
Calibration
■ PCI-9112 : Calibrate Analog Output on 5V
■ PCI-9112A : Calibrate Analog Output on 10V
■DIN-20P-01
Terminal Board with One 20-pin Ribbon Connector and DIN-Rail Mounting
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin D-sub Male Connector
■ACLD-9138-01
General-Purpose Terminal Board with One 37-pin D-sub Connector
■ACLD-9188-01
General-Purpose Terminal Board with Two 20-pin Ribbon Connectors and One 37-pin
D-sub Connector
■ACLD-9182A-01
Terminal Board with 16-CH Isolated Digital Inputs
■ACLD-9185-01
Terminal Board with 16-CH Isolated Digital Inputs
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
■ACL-10137-1MF
37-pin D-sub male/female cable, 1 M
+5 V
+12 V
460 mA typical
110 mA typical
3
■ACL-10120-1
20-pin flat cable, 1 M
■ACL-10237-1
37-pin D-sub male/male flat cable, 1 M
* For more information on mating cables, please refer to
P3-48/49.
Ordering Information
■PCI-9112
16-CH 12-Bit 110 kS/s Multi-Function DAQ Card
(AO Calibrated on 5V)
■PCI-9112A
16-CH 12-Bit 110kS/s Multi Function DAQ Card
(AO Calibrated on 10V)
General Specifications
■ I/O connector: 37-pin D-sub female
■ Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■ Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
PCI-9112A
2
■ Dimensions (not including connectors)
• 175 mm x 107 mm (6.82" x 4.17")
www.adlinktech.com 3-26
4
GPIB & Bus Expansion
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector and DIN-Rail Mounting
DAQ
■
Supports a 3.3 V or 5 V PCI bus (PCI-9112)
12-Bit A/D resolution
Up to 110 kS/s sampling rate
16-CH single-ended or 8-CH differential inputs
Bipolar or unipolar analog input ranges
Programmable gains of x0.5, x1, x2, x4, x8
Automatic analog inputs scanning
Bus-mastering DMA for analog inputs
2-CH 12-Bit multiplying analog outputs
16-CH TTL digital inputs and 16-CH TTL digital outputs
1-CH 16-Bit general-purpose timer/counter
For PCI-9112:
Modular Instruments
Features
0.5
1
2
4
8
Input Range
Bipolar
Unipolar
±10 V
±5 V
0 to 10 V
±2.5 V
0 to 5 V
±1.25 V
0 to 2.5 V
±0.625 V
0 to 1.25 V
PXI/PXIe
Terminal Boards & Cables
Specifications
1
PCI-9113A
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
Terminal Boards & Cables
Specifications
Analog Input
■ Number of channels: 32 single-ended or 16
differential
■ Resolution: 12 Bit
■ Conversion time: 8 μs
■ Maximum sampling rate: 100 kS/s
■ Input signal ranges
Input Range
Gain
1
10
100
Features
■
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 5 V PCI bus
12-Bit A/D resolution
Up to 100 kS/s sampling rate
32-CH single-ended or 16-CH differential inputs
Onboard 1 k-sample A/D FIFO
Bipolar or unipolar analog input ranges
Programmable gains of x1, x10, x100
Automatic analog inputs scanning
Onboard low-pass filtering capability for analog inputs
2500 VRMS optical isolation
Compact, half-size PCB
■OS Information
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-27 www.adlinktech.com
Unipolar
0 to 10 V
0 to 1 V
0 to 0.1 V
■
Accuracy: 0.01% of FSR ± 1 LSB
■ Input coupling: DC
■ Overvoltage protection: continuous ±35 V
■ Input impedance: 1 GΩ
■ Trigger modes: software, pacer
■ FIFO buffer size: 1 k samples
■ Data transfers: polling, interrupt
■ Isolation Voltage: 2500 VRMS
General Specifications
■
I/O connector: 37-pin D-sub female
■
Operating temperature: 0˚C to 55˚C (32˚F to 131˚F )
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
+5 V
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
Bipolar
±10 V
±5 V
±1 V
±0.5 V
±0.1 V
±0.05 V
960 mA typical
■
Dimensions (not including connectors)
173 mm x 107 mm (6.74” x 4.17”)
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One
37-pin D-sub Male Connector
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
■ACL-10137-1MF
37-pin D-sub male/female cable, 1 M
* For more information on mating cables, please refer to
P3-48/49.
Ordering Information
■PCI-9113A
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
General-Purpose DAQ
cPCI-9116
64-CH 16-Bit 250 kS/s Multi-Function DAQ Card
CompactPCI
Terminal Boards & Cables
Analog Input
■ Number of channels: 64 single-ended or
32 differential (software selectable per channel)
■ Resolution: 16 Bit
■ Maximum sampling rate: 250 kS/s
■ Input signal ranges (software programmable)
Gain
1
2
4
8
■
■
■
■
■
■
■
■
■
■
■
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Ordering Information
■cPCI-9116
64-CH 16-Bit 250 kS/s Multi-Function DAQ Card
Gain
Accuracy
1
0.01% of FSR ± 1 LSB
2, 4
0.02% of FSR ± 1 LSB
8
0.04% of FSR ± 1 LSB
■ Input coupling: DC
■ Overvoltage protection: Continuous ±35 V
■ Input impedance: 1 GΩ
■ Trigger modes: Software, pre-trigger, post-trigger,
middle trigger, delay trigger, and repeated trigger
■ Channel-gain queue size: 512 configurations
■ FIFO buffer size: 1 k samples
■ Data transfers:
polling, interrupt, bus-mastering DMA
■OS Information
* For more information on mating cables, please refer to P3-48/49.
2
3
DAQ
■
3U/6U Eurocard form factor, CompactPCI compliant (PICMG 2.0 R2.1)
16-Bit A/D resolution, up to 250 kS/s sampling rate
Up to 250 kS/s sampling rate
64-CH single-ended or 32-CH differential inputs
Onboard 1 k-sample A/D FIFO
Bipolar or unipolar analog input ranges
Programmable gains of x1, x2, x4, x8
512-configuration channel-gain queue
Bus-mastering DMA for analog inputs
8-CH TTL digital inputs and 8-CH TTL digital outputs
1-CH 16-Bit general purpose timer/counter
■ACL-102100-1
100-pin SCSI-II cable (mating with AMP-787082-9), 1 M
Accuracy
Features
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (cables are not included.)
Modular Instruments
Input Range
Bipolar
Unipolar
±5 V
0 to 10 V
±2.5 V
0 to 5 V
±1.25 V
0 to 2.5 V
±0.625 V
0 to 1.25 V
PXI/PXIe
Specifications
1
Digital I/O
■
Number of channels: 8 inputs and 8 outputs
Compatibility: 5 V/TTL
■ Data transfers: programmed I/O
■
General-Purpose timer/counter
■ Number of channels: 1
■ Resolution: 16 Bit
■ Compatibility: 5 V/TTL
■ Base clock available:
24 MHz, external clock up to 24 MHz
4
General Specifications
■
I/O connector: 100-pin SCSI-II female
■ Operating temperature: 0˚C to 55˚C (32˚F to 131˚F)
■ Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
+5 V
+12 V
560 mA typical
100 mA typical
GPIB & Bus Expansion
■ Dimensions (not including connectors)
• 160 mm x 100 mm (6.24" x 3.9") (3U)
www.adlinktech.com 3-28
PCI-6308V/6308A
8-CH 12-Bit Isolated Analog Output Cards
Specifications
Isolated Analog Output
■ Number of channels: 8 voltage outputs
(PCI-6308V & PCI-6308A)
■ Resolution: 12 Bit
■ Output ranges (jumper selectable)
Bipolar
Unipolar
PCI-6308A
Input Range
±10 V
0 to 10 V, 0 to EXTREF
■
Settling time: 16 μs (20 V step)
■
Maximum update interval:
90 μs for four channels simultaneously
Features
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 5 V PCI bus
12-Bit D/A resolution (PCI-6308V & PCI-6308A)
Isolated 8-CH 12-Bit voltage output
(PCI-6308V & PCI-6308A)
Isolated 8-CH 12-Bit current output (PCI-6308A)
Bipolar or unipolar output ranges
External reference input for user-defined ranges
4-CH isolated digital outputs and 4-CH isolated
digital inputs
2500 VRMS optical isolation
Compact, half-size PCB
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-29 www.adlinktech.com
■
Gain error: ±0.2 % max.
■
DNL: ±1 LSB
■ Output driving capacity: ±5 mA
■ Isolation voltage: 2500 VRMS
■ Output initial status:
0 V (after RESET or POWER-ON)
■ Data transfers: programmed I/O
Current
Output (PCI-6308A)
■ Number of channels: 8
■ Resolution: 12 Bit
■ Output ranges (software programmable):
0-20 mA, 4-20 mA, and 5-25 mA
■ Gain error: 0.3%
■ Settling time: 17 μs (0-20 mA)
■ Slew rate: 1.3 mA/μs
■ DNL: ±1 LSB maximum
■ Output resistance: 10 GΩ typical
■ Current load resistance: 0 - 500 Ω
■ Output initial status:
4 mA (after RESET or POWER-ON)
■ Data transfer: programmed I/O
Isolated Digital Input
■ Number of channels: 4
■ Maximum input range: 24 V, non-polarity
■ Digital logic levels
• Input high voltage: 5 - 24 V
• Input low voltage: 0 - 1.5 V
■ Input resistance: 2.4 kΩ @ 0.5 W
■ Isolation voltage: 2,500 VRMS
■ Data transfers: programmed I/O
Isolated Digital Output
■ Number of channels: 4 (PCI-6308V & PCI-6308A)
■ Output type: photo-coupler transistors
■ Supply voltage: 5 to 35 V
■ Isolation voltage: 2,500 VRMS
■ Data transfers: programmed I/O
General Specifications
■ I/O connector: 37-pin D-sub female
■ Operating temperature: 0˚C to 55˚C (32˚F to 131˚F )
■ Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
Device
+5 V
+12 V
PCI-6308V
220 mA typical
175 mA typical
PCI-6308A
220 mA typical
250 mA typical
530 mA maximum
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
Terminal Boards & Cables
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector
and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
■ACL-10137-1MF
37-pin D-sub male/female cable, 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-6308V
8-CH 12-Bit Isolated Voltage Output Card
■PCI-6308A
8-CH 12-Bit Isolated Voltage & Current
Output Card
Analog Output
PCI-6202
4-CH 16-Bit 1 MS/s Analog Output & 32-CH Isolation DIO Card
1
Terminal Boards & Cables
Analog Output
■
Resolution: 16 Bit
■
Number of channels: Four (simultaneous update)
■
Maximum update rate: 1 MS/s
■
FIFO buffer size: 8k Samples (4-CH Sharing)
■
Output range: ±10 V
■
DNL: Less than ±1 LSB
■
Offset Error: 0.3 mV
■
Positive Gain Error: 0.3 mV
■
Negative Gain Error: 0.3 mV
■
Settling Time: 3 μs
■
Slew Rate: 20 V/μs
Features
■
Rise Time: 0.67 μs
■
Supports a 32-Bit 3.3 V or 5 V PCI bus
■
Falling Time: 0.705 μs
■
Hardware-based waveform generation
■
Output Current Capacity: 5 mA
■
Trigger source: Software, External digital, SSI bus
■
Data Transfer: Software polling, DMA
■
DNL Linearity less than 1 LSB
■
Digital triggering for waveform generation
■
16-CH isolation digital inputs & 16-CH isolation digital outputs
8-CH TTL DI and 8-CH TTL DO
■
2-CH timer/counter, base clock: 40 MHz
■
4-CH PWM output
■
3-CH encoder inputs, supporting AB phase and CW/CCW
■
Multiple card synchronization through SSI
(System Synchronization Interface) bus
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
P3-48/49.
SSI Bus Cables
(for multiple PCI/PCIe cards synchronization)
■ACL-SSI-2
SSI Bus cable for two devices
■ACL-SSI-3
SSI Bus cable for three devices
■
Number of channels: 16
■
Sink current limitation: 250 mA for one channel @ 100% duty
■
Supply voltage: 5-35 VDC
■
Isolation voltage: 2500 VRMS
■ACL-SSI-4
SSI Bus cable for four devices
Ordering Information
Isolated Digital Output
■PCI-6202
4-CH 16-Bit 1 MS/s Analog Output & 32-CH
Isolation DIO Card
2
3
Encoder Input
■ Number of channels: Three Encoder type
• CW/CCW encoder
• x1 AB phase encoder
• x2 AB phase encoder
• x4 AB phase encoder
■Software Compatibility
* For more information about mating cables, please refer to
■ACL-10568-1
68-pin SCSI-VHDCI cable (mating with AMP-787082-7), 1 M
DAQ
■
■DIN-68S-01
Terminal Board with One 68-pin SCSI-II connector and DIN-Rail Mounting (Cables are not included.)
Modular Instruments
PXI/PXIe
Specifications
Function I/O
■
Digital I/O: Eight DO (3.3 V TTL Level)/Eight DI
4
GPIB & Bus Expansion
(3.3 V or 5 V TTL Level)
■ General Timer/Counter: Two 32-Bit, Base clock:
80 MHz, external to 10 MHz
■ Pulse Generation: Four PWM Outputs
• Single pulse generation
• Pulse train generation
■ AFI0/AFI1: D/A Convert Clock or Start Trigger
General Specifications
■
PCI Bus: 5 V and 3.3 V universal PCI bus
■
I/O Connector: Two 68-pin SCSI-VHDCI female
■
Operation temperature: 0˚C to 55˚C (32˚F to 131˚F)
■
Storage temperature: -20˚C to 70˚C (-4˚F to 158˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements:
+5 V
500 mA typical
+12 V
110 mA typical
■ Dimensions: 175 mm x 107 mm (6.82” x 4.17”)
(not including connectors)
www.adlinktech.com 3-30
Analog Output
PCI/PCIe/cPCI-6208/6216 Series
8/16-CH 16-Bit Analog Output Cards
CompactPCI
Specifications
Terminal Boards & Cables
Voltage Output
■
Number of channels
• 8 voltage outputs (PCI/PCIe/cPCI-6208V-GL & PCI-6208V-GL
PCI-6208A)
• 16 voltage outputs (PCI/PCIe/cPCI-6216V-GL)
PCIe-6208V-GL
■
Resolution: 16 Bit
■
Monotonicity: 15 Bit typical
■
Output ranges: ±10 V
■
Slew rate:26 V/μs typical
■
Settling time: 130 μs typical (20 V step)
■
Gain Error: ±0.2% maximum
■
DNL: ±1 LSB typical
■
Output driving capacity: ±5 mA maximum
■
Output initial status: 0 V
■
Data transfer: programmed I/O
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector
and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACLD-9137F-01
General-Purpose Terminal Board with One 37-pin
D-sub female Connector.
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
■ACL-10137-1MF
37-pin D-sub male/female cable, 1 M
* For more information about mating cables, please refer to
P3-48/49.
Current Output
■
Number of channels: 8 current outputs (PCI-6208A)
■
Resolution: 15 Bit typical
■
Monotonicity: 14 Bit typical
■
Output ranges: (Software programmable)
0-20 mA, 4-20 mA, 5-25 mA
cPCI-6208V-GL
Features
■
Supports a 32-Bit 3.3 V or 5 V PCI bus (PCI-6208/6216-GL)
■ x1 lane PCI Express® Interface (PCIe-6208/6216-GL)
■ 3U Eurocard form factor, CompactPCI compliant PICMG 2.0 R2.1 (cPCI-6208/6216 series)
■ 16-Bit D/A resolution
■ Effective 15-Bit resolution current transducers
(PCI-6208A)
■ 8-CH voltage outputs (PCI/PCIe/cPCI-6208V-GL)
■ 16-CH voltage outputs (PCI/PCIe/cPCI-6216V-GL)
■ 8-CH current outputs (PCI-6208A)
■ Bipolar analog output range
■ 4-CH TTL digital inputs and 4-CH TTL digital outputs
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-31 www.adlinktech.com
Ordering Information
■PCI-6208V-GL
8-CH 16-Bit Voltage Output Card
■PCI-6216V-GL
16-CH 16-Bit Voltage Output Card
■
Slew rate: 1.3 mA/μs typical
■
Settling time: 17 μs typical (20 mA step)
■
Span Error: ±0.3% typical
■
Output Initial Status: 4 mA (after RESET or POWER-ON)
■
Data transfer: programmed I/O
■PCI-6208A
8-CH 16-Bit Voltage and Current Output Card
■cPCI-6208V-GL
8-CH 16-Bit Voltage Output Module
Digital I/O
■
Number of channels: 4 inputs and 4 outputs
■
Compatibility: 5 V/TTL
■
Data transfers: programmed I/O
■cPCI-6216V-GL
16-CH 16-Bit Voltage Output Module
■PCIe-6208V-GL
8-CH 16-Bit Voltage Output PCI Express® Card
General Specifications
■
I/O connector: One 37-pin D-sub female
■
Operating temperature: 0˚C to 50˚C (32˚F to 122˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
Device
+5 V
+12 V
PCI-6208V-GL
650 mA typical
170 mA typical
PCI-6216V-GL
1.2 A typical
280 mA typical
PCI-6208A
670 mA typical
380 mA typical
cPCI-6208V
500 mA typical
200 mA typical
cPCI-6216V
1 A typical
300 mA typical
Device
+3.3 V
+12 V
PCIe-6208V-GL
310 mA typical
380 mA typical
PCIe-6216V-GL
315 mA typical
660 mA typical
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”) (PCI-6208/6216)
168 mm x 112 mm (6.55” x 4.36”) (PCIe-6208/6216)
160 mm x 100 mm (6.24” x 3.9”) (cPCI-6208/6216)
■PCIe-6216V-GL
16-CH 16-Bit Voltage Output PCI Express® Card
High-Speed DIO
PCIe-7360
100 MHz 32-CH High-Speed Digital I/O Card
1
ADLINK’s PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O, with data rates up to 400
MB/s are available through the x4 PCI Express® interface, and clock rates up to 100 MHz internal or 200 MHz external,
ideally suiting high speed and large scale digital data acquisition or exchange applications, such as digital image capture,
video playback and IC testing.
PXI/PXIe
Introduction
Specifications
Clocking Mode
Digital I/O
■
■
■
■
■
■
■
■
■
■
Software Support
■
Internal clock: up to 100 MHz (100 MHz / N; direction, with selectable logic levels: 1.8 V, 2.5 V,
1<N<65535)
3.3 V (software selectable)
■
Power-up status: All digital inputs
■
Impedance:
■
External clock: up to 100 MHz (support 8/16/24/
32-bit data width for DI/DO); up to 200 MHz
(support 8/16-bit data width for DI only)
• Input: 10 kΩ
■
Handshake
• Output: 50 Ω
■
Burst handshake
■
Input protection: -1 to 6 V
■
Data transfer: Programmable I/O, bus-mastering Trigger Sources
DMA with scatter-gather
■
■
Maximum data transfer rate: 400 MB/s
■
Software trigger
■
External digital trigger: AFI[0…7]
Trigger Modes
Digital logic levels:
Logic Levels
Digital Input
Digital Output
2
1.8 V
2.5 V
3.3 V
Min. input high voltage
1.2 V
1.6 V
2V
■
Post trigger, Retrigger, Pattern match, Handshake
Change of State Interrupt
Max. input low voltage
0.63 V
0.7 V
0.8 V
Min. output high voltage
1.6 V
2.3 V
3.1 V
Max. output low voltage
0.2 V
0.2 V
0.2 V
channel change-of-state
Max. output driving current
8 mA
16 mA
32 mA
■
Interrupt sources: Any of 32 channels or a pre-define
Application Function I/O
■
3
DAQ
■
x4 lane PCI Express Interface
8/16/24/32-CH at up to100MHz for DI or DO
8/16-CH at up to 200MHz for DI in external clock mode
400 MB/s maximum throughput
Voltage level software selectable from 1.8 V, 2.5 V, and
3.3 V
80-step phase shift in external clock mode
Per group (8-bit) input/output direction selectable
Support for I2C and SPI programmable serial interfaces
for external device communication
Scatter-gather DMA support
Flexible handshake and external digital trigger modes
8-channel auxiliary programmable I/O
®
32-channels, per group (8-channel) input/output Modular Instruments
Features
■
8 channels
■ Supported modes: static I/O, I2C or SPI master node, external clock input/output, external digital trigger input, handshake
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■ Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
4
GPIB & Bus Expansion
Terminal Boards & Cables
■ DIN-68H-01
Terminal board with one 68-pin SCSI-VHDCI connector and 0 or 50 Ω jumper selectable impedance (Cables are not included.)
■ ACL-10279
• 68-pin SCSI-VHDCI cable with 50 Ω impedance
■ SMB-SMB-1M
• SMB to SMB cable, 1M
* For more information about mating cables, please refer to
P3-48/49.
Ordering Information
■ PCIe-7360
100 MHz 32-CH High-Speed Digital I/O PCI Express® Card
PCIe-7360 Block Diagram
www.adlinktech.com 3-32
PCIe-7350
50 MHz 32-CH High-Speed Digital I/O Card
Specifications
Terminal Boards & Cables
■ DIN-68H-01
Terminal Board with One 68-pin SCSI-VHDCI Connector and 0 or 50 Ω Jumper Selectable Impedance (Cables are not included.
Digital I/O
■
Number of channels:
32, per group (8-channel) input/output direction selectable
■
Logic levels: 1.8 V, 2.5 V, 3.3 V (software selectable)
■ ACL-10279
■
Power-up status: All digital inputs
■
Impedance:
■ SMB-SMB-1M
• Input: 10 kΩ
• Output: 50 Ω
■
■
■
■
■
■
■
■
■
■
x1 lane PCI Express® Interface
Maximum 50 MHz clock rate from internal timer or
100 MHz from external clock
200 MB/s maximum throughput
Software selectable voltage level of 1.8 V, 2.5 V, and 3.3 V
16-steps phase shift in external clock mode
Per group (8-Bit) input/output direction selectable
Supports I2C and SPI programmable serial interfaces for external device communication
Scatter-gather DMA support
Flexible handshaking and external digital trigger modes
8-channel auxiliary programmable I/O
■
Input protection: -1 to 6 V
■
Data transfer: Programmable I/O, bus-mastering ■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■
Maximum data transfer rate: 200 MB/s
■
Digital logic levels:
Digital Input
Digital Output
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
Ordering Information
1.8 V
2.5 V
3.3 V
Min. input high voltage
1.2 V
1.6 V
2V
Max. input low voltage
0.63 V
0.7 V
0.8 V
Min. output high voltage
1.6 V
2.3 V
3.1 V
Max. output low voltage
0.2 V
0.2 V
0.2 V
Max. output driving current
8 mA
16 mA
32 mA
Clocking mode
■
Internal clock: Max. 50 MHz (100 MHz / N; 2<N<65535)
■
External clock: Max. 100 MHz (support 8/16-Bit data width only, data throughput must be less than 200 MB/s)
■
Handshaking
■
Burst handshaking
■Software Compatibility
Logic Levels
Trigger sources
■
Software trigger
■
External digital trigger: AFI[0…7]
• AD-Logger, DAQBench, DAQMaster
Trigger modes
■
Post trigger, Retrigger, Pattern match, Handshaking
Change of State Interrupt
■
Interrupt sources: Any of 32 channels or a pre-define
channel Change-of-State
Application Function I/O
■
Number of channels: 8
■ Supporting modes: static I/O, I2C or SPI master node, external clock input/output, external digital trigger input, handshaking
3-33 www.adlinktech.com
SMB to SMB Cable, 1M
* For more information about mating cables, please refer to
P3-48/49.
DMA with scatter-gather
Features
68-pin SCSI-VHDCI Cable with 50 Ω Impedance
■ PCIe-7350
50 MHz 32-CH High-Speed Digital I/O PCI Express® Card
High-Speed DIO
PCI/PCIe-7300A, cPCI-7300
32-CH 80 MB/s High-Speed Digital I/O Cards
CompactPCI
Digital I/O
■
Numbers of channel (Software configurable)
• 16 DI & 16 DO
PCI-7300A
■
Base clock: 10 MHz
■
Timer #0 as digital input pacer
■
Timer #1 as digital output pacer
■
Timer #2: as interrupt source
• 32 DI
Auxiliary digital I/O
• 32 DO
■
Compatibility: 5 V/TTL
■
Digital logic levels
■
Compatibility: 5 V/TTL
■
Data transfers: programmed I/O
General Specifications
• Output low voltage: 0.5 V maximum
Input load
• Terminator OFF
■
■
■
■
■
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
-
Input low current: 20 mA
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
-
Termination voltage: 2.9 V
-
Input high current: 1 mA
-
Input low current: 22.4 mA
■
Output driving capacity
■
■
■
■
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
Data transfers:
Bus-mastering DMA with Scatter/Gather
■
■
2 M double words (8 MB) for non-chaining mode DMA
■
No limitation for chaining mode (scatter/gather) DMA
Max transfer rate
■
+5 V
1.0 A typicall
287 mA typical
543 mA typical
1.0 A typical
DO: 80 MBytes/s, 32-Bit output @ 20 MHz
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (Cables are not included.)
Note:
Legacy DIN-502S can be replaced by two DIN-50S-01
and ACL-10252-1 (100-Pin to two 50-Pin Cable, 1 M)
DI: 80 MBytes/s, 32-Bit input @ 20 MHz
■ ACL-102100-1
100-pin SCSI-II cable (mating with AMP-787082-9), 1 M
Trigger
* For more information on mating cables, please refer to P3-48/49.
■
DI_TRG for digital inputs,
DO_TRG for digital outputs
■
Compatibility: 5 V/TTL
■
Trigger types: rising or falling edges
■
Minimum pulse width: 32 ns
Clocking mode
■
Internal clock
• Internal clock sources: 20 MHz, 10 MHz, Timer#0 output (digital input pacer) and Timer #1
Ordering Information
■PCI-7300A
80 MB/S High-Speed 32-CH Digital I/O PCI Card
■PCIe-7300A
80 MB/S High-Speed 32-CH Digital I/O PCIe Card
■cPCI-7300
80 MB/s High-Speed 32-CH Digital I/O CompactPCI Card
output (digital output pacer)
■
External clock up to 40 MHz
■
Handshaking
■
Burst handshaking
3
Terminal Boards & Cables
Data width: 32/16/8 Bit (programmable)
Data transfer count
PCI-7300A
Onboard
terminator on
Onboard
terminator off
■ Dimensions (not including connectors)
• 179 mm x 106 mm (6.98" x 4.13") (PCI-7300A)
• 168 mm x 112 mm (6.55” x 4.36") (PCIe-7300A)
• 160 mm x 100 mm (6.24" x 3.9") (cPCI-7300)
• Sink current: 48 mA
■
Power
830 mA typical
+12 V 119 mA typical
PCIe-7300A
+3.3 V 499 mA typical
cPCI-7300 +5 V
830 mA typical
• Source current: 8 mA
Device
• AD-Logger, DAQBench, DAQMaster
www.adlinktech.com 3-34
4
GPIB & Bus Expansion
■
x1 lane PCI Express® Interface (PCIe-7300A)
Supports a 32-Bit 5 V PCI bus (PCI-7300A)
3U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R2.1) (cPCI-7300)
32-CH 5 V/TTL digital inputs/outputs
20 MHz (80 MB/s) maximum transfer rate
8, 16, or 32-Bit transfers
4 auxiliary DI & 4 auxiliary DO
Onboard 64 kB FIFO
Onboard programmable timer pacer clock
Timed digital input sampling controlled by internal
timer or external clock
Independent trigger signals to start data
acquisition and pattern generation
Scatter-gather DMA
Supports handshaking digital I/O transfer mode
Repeated digital pattern generation from FIFO
Active terminators for high-speed and longdistance
data transfer
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
DAQ
■
I/O connector: One 100-pin SCSI-II female
■
Transfer characteristics
■
■
Input high current: 1 mA
Features
-
• Terminator ON
- Termination resistor: 111 Ω
cPCI-7300
2
Modular Instruments
• Output high voltage: 2.7 V minimum
PCIe-7300A
Number of channels
• 4-CH digital outputs
• Input low voltage: 0-0.8 V
■
■
• 4-CH digital inputs
• Input high voltage: 2-5.25 V
PXI/PXIe
Programmable counter
Specifications
1
High-Speed DIO
PCI/PCIe-7200
32-CH DI & 32-CH DO 12 MB/s High-Speed Cards
Specifications
Terminal Boards & Cables
Digital I/O
PCI-7200
■ Number of channels:
• 32-CH digital inputs
• 32-CH digital outputs
■ Compatibility: 5 V/TTL
■ Data transfer rate
• 12 MB/s with external 3 MHz clock, handshaking
or external strobe
• 8 MB/s with internal 2 MHz timer pacer
■ Digital logic levels
• Input high voltage: 2-5.25 V
• Input low voltage: 0-0.8 V
• Output high voltage: 2.7 V minimum
• Output low voltage: 0.5 V maximum
■ Output driving capacity
• Source current: 3.0 mA
• Sink current: 24 mA
■ Data transfers:
• programmed I/O, interrupt, bus-mastering DMA
Programmable Counter
PCIe-7200
Features
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 5 V PCI bus (PCI-7200)
x1 lane PCI Express® interface (PCIe-7200)
32-CH TTL digital inputs and 32-CH TTL digital outputs
Up to 12 MB/s transfer rate
Bus-mastering DMA for both digital inputs and outputs
Onboard programmable timer pacer clock
Supports handshaking digital I/O transfer mode
Multiple programmable interrupt sources
5 V power available on connectors
Compact, half-size PCB (PCI-7200/PCIe-7200)
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-35 www.adlinktech.com
■
Base clock: 4 MHz
Timer 0: DI clock source
■ Timer 1: DO clock source
■ Timer 2: Base clock source of timer 0 & 1
Interrupt
■
■ Sources:
EO_ACK, EI_REQ, Timer 0, Timer 1 or Timer 2
General Specifications
■ I/O connector
• PCI/PCIe-7200
-37-pin D-sub female
-40-pin Header
■
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative humidity: 5% to 95%, non-condensing
■ Power requirements
■
Device
Power Consumption
PCI-7200
5 V @ 720 mA typical
PCIe-7200
12 V @ 200 mA
3.3 V @ 500 mA
■ Dimensions (not including connectors)
• 148 mm x 102 mm (5.77" x 3.97") (PCI/PCIe-7200)
PCI/PCIe-7200:
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACLD-9137F-01
General-Purpose Terminal Board with One 37-pin
D-sub Female Connector
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
■ACL-10137-1MF
37-pin D-sub male/female cable, 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-7200
12 MB/s High-Speed 32-CH DI & 32-CH DO Card
■PCIe-7200
12 MB/s High-Speed 32-CH DI & 32-CH DO
PCI Express® card
Digital I/O
PCI-7260
8-CH High-Power Relay Outputs & 8-CH Isolated Digital Inputs Card
1
PXI/PXIe
Specifications
Ordering Information
Relay Output
■PCI-7260
8-CH High-Power Relay Outputs & 8-CH
Isolated Digital Inputs Card
■
Number of channels: 8
■ Relay type: Non-latching SPST-NO + SPST-NC
(for output indicator)
■ACL-10337 (for JP2/JP3)
Two 20-Pin Header to 37-Pin D-Sub PC Back Panel
2
Modular Instruments
■ Contact rating
• AC: 250 V @ 5 A
• DC: 30 V @ 5 A
■ Insulation resistance: 1000 MΩ min. (at 500 VDC)
■ Breakdown voltage: 2000 VAC, 50/60 Hz for 1 minute
■ Contact resistance: 30 mΩ max
■ Operate time: 10 ms max.
■ Release time: 10 ms max.
■ LED indicators: onboard LEDs for relay status
■ Expected relay life
> 105 operations @ 5 A, 250 VAC/30 VDC
■ Data transfer: programmed I/O
Isolated Digital Input
■
Number of channels: 8
■ Input current
• Rated current: 10 mA
• Max current: 50 mA, for isolated input.
■
■
■
■
■
■
■
■
■
■
■
■
■
Input resistance: 4.7 KΩ @ 0.5 W
■
Input mode: AC-filter/ Non-AC-filter
■
Isolation voltage: 2,500 VRMS channel-to-system
■
Interrupt sources
• Change-of-state (COS)
• CH0/CH1 rising edge
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Data transfer: programmed I/O
Isolation +5 V Power Supply
■
Output Voltage: +5 V
■
Output Current: 170 mA max. (@ 40˚C)
4
Relay Status Output
■
Number of channels: 8
■
Driving capacity: 15 mA
■OS Information
■
GPIB & Bus Expansion
Supports a 32-Bit 3.3 V or 5 V PCI bus
8-CH high power relay outputs
5 A at 250 VAC
5 A at 30 VDC
8-CH isolated digital inputs
8-CH relay status outputs
1-CH emergency shutdown input
Pluggable connector for high current input
Onboard LED indicators for relay status
Initial and safety state setting by DIP switches
Interrupt generated from
• COS (Change-of-State) of DI
• CH0/CH1 rising edge
Built-in watchdog timer
DAQ
Features
3
■ Input voltage: Up to 24 VDC
• Input high voltage: 10-24 V
• Input low voltage: 0-2 V
General Specifications
■
I/O connector
• 18-pin pluggable terminal block connector
• 20-pin ribbon male x2
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 70˚C (-4˚F to 158˚F)
■
Relative humidity: 35% to 85%, non-condensing
■
Power requirements
+5 V
510 mA typical
990 mA typical (when all relays are activated simultaneously)
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
Certificate
■
EMC/EMI: CE, FCC Class A
■
Safety: EN61010: 2001
www.adlinktech.com 3-36
PCI/LPCI/LPCIe-7250, PCI-7251, cPCI-7252
8-CH Relay Outputs & 8-CH Isolated DI Cards
CompactPCI
Specifications
Relay Output
■
Number of channels: 8
■
Relay types
-
PCI-7250+PCI-7251
LPCI-7250
■
Contact rating
-
AC: 120 V @ 0.5 A
-
DC: 24 V @ 1 A
■
Breakdown voltage: 1000 VRMS
■
Contact resistance: 100 m
■
Relay ON/OFF time
• Operate time: 8 ms
• Release time: 8 ms
cPCI-7252
■
LED indicators: onboard LEDs for relay status
■
Expected life
• PCI-7250/7251 & cPCI-7252
- >5x105 operations @ 1 A, 24 VDC
-
Features
■
Supports a 32-Bit 5 V PCI bus (PCI-7250/7251)
Supports a 32-Bit 3.3 V or 5 V PCI bus (LPCI-7250)
■ x1 lane PCI Express Interface (LPCIe-7250)
■ 3U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R2.1) (cPCI-7252)
■ 4-CH SPDT & 4-CH SPST relays (PCI-7250)
■ 8-CH SPDT & 8-CH SPST relays (PCI-7250 + 1 x PCI-7251)
■ 12-CH SPDT & 12-CH SPST relays (PCI-7250 + 2 x PCI-7251)
■ 16-CH SPDT & 16-CH SPST relays (PCI-7250 + 3 x PCI-7251)
■ 8-CH SPDT (LPCI-7250/LPCIe-7250/cPCI-7252)
■ Non-latching relays
■ Onboard LED indicators for relay status
■ Onboard relay driving circuits
■ Relay output status read back
■ 8-CH isolated digital inputs (cPCI-7252/PCI-7250/LPCI-7250/
LPCIe-7250)
■ 16-CH isolated digital inputs (PCI-7250 + 1 x PCI-7251)
■ 24-CH isolated digital inputs (PCI-7250 + 2 x PCI-7251)
■ 32-CH isolated digital inputs (PCI-7250 + 3 x PCI-7251)
■ Onboard low-pass filtering for digital inputs
■ Compact, low-profile size PCB (LPCI-7250/LPCIe-7250)
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-37 www.adlinktech.com
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
• LPCI-7250/LPCIe-7250/cPCI-7252
- Channel 0-7: SPDT (normal open)
• LPCI-7250/LPCIe-7250
- DC: 30 V @ 2 A
LPCIe-7250
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Channel 4-7: SPST (normal open)
• PCI-7250/7251 & cPCI-7252
■
• PCI-7250/7251:
- Channel 0-3: SPDT (normal open)
PCI-7250
>2x105 operations @ 0.5 A, 120 VAC
• LPCI-7250/LPCIe-7250:
- >105 operations @ 2 A, 30 VDC
-
■
>5x105 operations @ 1 A, 30 VDC
Data transfers: programmed I/O
Isolated Digital Input
■
Number of channels: 8
■
Maximum input range: 24 V, non-polarity
■
Digital logic levels
• 0-24 V, non-polarity
- Input high voltage:
5-24 V (PCI/LPCI/LPCIe-7250, PCI-7251)
3-24 V (cPCI-7252)
-
Input low voltage:
0-1.5 V (PCI/LPCI/LPCIe-7250, PCI-7251)
0-1 V (cPCI-7252)
■
Input resistance: 2.2 kΩ @ 0.33 W (PCI/LPCI/LPCIe-
7250, PCI-7251) 1.2 kΩ @ 0.5 W (cPCI-7252)
■
Isolation voltage: 5000 VRMS
■
Data transfers: programmed I/O
General Specifications
■
I/O connector
Device
Power Consumption
PCI-7250
+5 V @ 140 mA typical
PCI-7251
+5 V @ 125 mA typical
LPCI-7250
+5 V @ 200 mA typical
LPCIe-7250
+3.3 V @ 280 mA
+12 V @ 180 mA
■ Dimensions (not including connectors)
• 162 mm x 107 mm (6.31” x 4.17") (PCI-7250)
• 141 mm x 102 mm (5.49" x 3.97") (PCI-7251)
• 120 mm x 65 mm (4.68" x 2.53") (LPCI-7250)
• 120 mm x 69 mm (4.68" x 2.69") (LPCIe-7250)
• 160 mm x 100 mm (6.24" x 3.9") (cPCI-7252)
Terminal Boards & Cables
PCI-7250/7251:
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector
and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin
D-sub Male Connector
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
LPCI-7250/LPCIe-7250/cPCI-7252:
■DIN-50S-01
Terminal Board with One 50-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ACL-10250-1
50-pin SCSI-II cable (mating with AMP-787082-5), 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-7250
8-CH Relay Outputs & 8-CH Isolated DI Card
■PCI-7251
8-CH Relay Outputs & 8-CH Isolated DI Extension Card for PCI-7250
■LPCI-7250
8-CH Relay Outputs & 8-CH Isolated DI Low-Profile PCI Card
• PCI-7250/7251
- 37-pin D-sub female
■LPCIe-7250
8-CH Relay Outputs & 8-CH Isolated DI Low-Profile PCI Express Card
• LPCI-7250/LPCIe-7250/cPCI-7252
50-pin SCSI-II female
■cPCI-7252
8-CH Relay Output & 16-CH Isolated DI Module
-
Digital I/O
PCI-7256
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
1
Relay Output
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
Number of channels: 16
■
Relay type: Latching SPDT (Form C), latching
■
The output status will keep unchanged when power-off
■
Isolation voltage: 1500 VRMS
■ Contact rating
• AC: 125 V @ 0.5 A
• DC: 30 V @ 1 A
■ Breakdown voltage: 1000 VRMS
■ Contact resistance: 60 mΩ
■ Relay ON/OFF time
• Operate time: 3 ms
• Release time: 3 ms
■ LED indicators
• Onboard LEDs for relay status
• Onboard connectors for external LED connection
■ Expected relay life:
• >2x105 operations @ 1 A, 30 VDC
• >105 operations @ 0.5 A, 125 VAC
■ Data transfer: programmed I/O
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Ordering Information
■PCI-7256
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
2
Isolated Digital Input
3
Isolated Power Supply
■
Output voltage: +5 V
■
Output current: 170 mA max @ 40˚C
General Specifications
■
I/O connector: 68-pin SCSI-II female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
4
GPIB & Bus Expansion
* For more information on mating cables, please refer to P3-48/49.
■ Number of channels: 16
■ Maximum input range: 24 V, non-polarity
■ Digital logic levels
• 0-24 V, non-polarity
- Input high voltage: 10-24 V
- Input low voltage: 0-2 V
■ Input resistance: 4.7 kΩ @ 0.5 W
■ Isolation voltage: 2500 VRMS channel-to-system
■ Interrupt sources: Change-of-state interrupt, digital
input channel 0 and 1
■ Data transfer: programmed I/O
■Software Compatibility
■DIN-68S-01
Terminal Board with One 68-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ACL-10569-1
68-pin SCSI-II cable (mating with AMP-787082-7), 1 M
DAQ
■
Supports a 32-Bit 3.3 V or 5 V PCI bus
16-CH latching SPDT relays
Latching relays
Power saving on relay actuation
Output status unchanged when power-off
Onboard LED indicators for relay status
Relay output status read back
Onboard relay driving circuits
Onboard connectors for external LED connection
16-CH isolated digital inputs
2500 VRMS optical isolation for digital inputs
Change-of-state (COS) interrupt
Onboard low-pass filtering for digital inputs
Two external interrupt sources
Onboard isolated +5 V power for dry contact inputs
Compact, half-size PCB
Board ID
■
Modular Instruments
Features
Terminal Boards & Cables
PXI/PXIe
Specifications
+5 V
340 mA typical
980 mA max. (when all relays are activated simultaneously)
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
www.adlinktech.com 3-38
PCI-7258
32-CH PhotoMos Relay Outputs & 2-CH Isolated DI Card
Specifications
Terminal Boards & Cables
Relay Output
■
Number of channels: 32
■
Relay type: PhotoMos SPST (Form A)
■
Load voltage (peak AC): 350 V
■
Continuous load current: 0.12 A
■
Peak load current: 0.3 A
■
Maximum switching power: 300 mW
■
Isolation voltage: 1500 VRMS
■
Output turn-on resistance: 17 Ω typical
■
Output off-state leakage current: 1 μA maximum
■
Turn-on time: 0.23 ms typical
■
Turn-off time: 0.04 ms typical
■
Data transfers: programmed I/O
Features
■
■
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 3.3 V or 5 V PCI bus
32-CH long-life PhotoMos relay outputs
Relay output status read back
1500 VRMS optical isolation for relay outputs
Onboard LED indicators for relay status
Onboard connectors for external LED connection
Onboard relay driving circuits
2-CH isolated digital inputs
Two external interrupt sources
2500 VRMS optical isolation for digital inputs
Compact, half-size PCB
Board ID
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-39 www.adlinktech.com
Isolated Digital Input
■
Number of channels: 2
■
Maximum input range: 24 V, non-polarity
■
Digital logic levels
• 0-24 V, non-polarity
-
Input high voltage: 5-24 V
-
Input low voltage: 0-1.5 V
■
Input resistance: 2.4 kΩ @ 0.5 W
■
Isolation voltage: 2500 VRMS
■
Interrupt sources: digital input channel 0 and 1
■
Data transfers: programmed I/O
General Specifications
■
I/O connector: 68-pin SCSI-II female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
+5 V
380 mA max.
■ Dimensions (not including connectors)
175 mm x 107 mm (6.82” x 4.17”)
■DIN-68S-01
Terminal Board with One 68-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ACL-10569-1
68-pin SCSI-II cable (mating with AMP-787082-7), 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-7258
32-CH PhotoMos Relay Outputs & 2-CH
Isolated DI Card
Digital I/O
PCI-7442/7443/7444
High-density 128-CH Isolated DIO/DI/DO Cards
1
Terminal Boards & Cables
Isolated Digital Input
PCI-7442
PCI-7443
Isolated Digital Output
■ Number of channels:
• 64 (PCI-7442)
• 128 (PCI-7444)
■ Output type: open drain Power MOSFET driver
■ Output range: 5 V to 40 V
■ Sink current: 250 mA for all channel @ 100% duty
(300 mA max.)
■ Isolation voltage: 1250 VRMS channel-to-system
■ Data transfer: programmed I/O
Ordering Information
■PCI-7442
64-CH Isolated DI and 64-CH Isolated DO card
■PCI-7443
128-CH Isolated DI card
■PCI-7444
128-CH Isolated DO card
■
Output Voltage: +5 V
■
Output Current: 100 mA max. (@ 40˚C)
3
Safety Functions (PCI-7442/7444 only)
■
Programmable power-up DO status
■ Watchdog timer
• Base clock available: 10 MHz, fixed
• Counter width: 32-Bit
General Specifications
■
I/O connector: 68-pin Dual port VHDCI female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
■
Device
+5 V
PCI-7442
PCI-7443
PCI-7444
800 mA typical
550 mA typical
800 mA typical
4
Dimension: 175 mm x 107 mm (6.82” x 4.17”)
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
2
GPIB & Bus Expansion
Supports universal 32-Bit 3.3 V and 5 V PCI bus, plug-and-play
High-density, opto-isolated digital input and/or digital output
• PCI-7442: 64-CH digital input and 64-CH digital output
• PCI-7443: 128-CH digital input
• PCI-7444: 128-CH digital output
■ 1250 VRMS isolation voltage
■ Programmable Change-of-State (COS) detection for all digital input channels
■ Voltage protection of up to 28 V for isolated input
■ Dry contact input (PCI-7442 only)
■ Up to 300 mA high-output driving capability for all output channels
■ 250 mA sink current on isolated output channels
■ Digital output status read back function
■ Digital output value retained after hot system reset
■ Programmable power-up DO initial status
■ Programmable safety DO status functions when
WDT interruption occurs
■ Watchdog timer counter prevents system crashes
(PCI-7442/PCI-7444 only)
■ 32-CH programmable TTL I/O function
■ Board ID feature
■
* For more information on mating cables, please refer to P3-48/49.
Isolation +5 V Power Supply (PCI-7442/7444 only)
Features
■
■ACL-10568F
68-Pin SCSI-VHDCI Flat Cable
DAQ
PCI-7444
■DIN-68S-01
Terminal Board with One 68-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ACL-10568D
Dual-68-Pin Head to Two 68-Pin SCSI-VHDCI Cable
Modular Instruments
■ Number of channels
• 64 (PCI-7442)
• 128 (PCI-7443)
■ Maximum input range: 28 V, non-polarity
■ Digital logic levels: 0 V to 28 V, non-polarity
• Input high voltage: 5 V to 28 V
• Input low voltage: 0 V to 1.5 V
■ Input resistance: 4.7 kΩ @ 0.5 W
■ ESD protection CKT switch (forward)
■ Isolation voltage: 1250 VRMS channel-to-system
■ Interrupt sources: 64/128-channel Change-of-State
(COS)
■ Data transfer: programmed I/O
PXI/PXIe
Specifications
• AD-Logger, DAQBench, DAQMaster
www.adlinktech.com 3-40
PCI/cPCI-7432/7433/7434
64-CH Isolated Digital I/O Cards
CompactPCI
Specifications
Isolated Digital Input
■
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
Number of channels
• 32 (PCI-7432/7432HIR, cPCI-7432)
cPCI-7432
cPCI-7433
• 64 (PCI-7433/7433HIR, cPCI-7433)
■
Maximum input range (Non-polarity)
• 24 V, non-polarity (PCI-7432/7433, cPCI-7432/7433)
■
PCI-7433
cPCI-7434
Digital logic levels: 0 V to 24 V, non-polarity
■
Input resistance
• 4.7 kΩ @ 0.5 W (PCI-7432HIR)
• 156 mm x 106 mm (6.08" x 4.13") (PCI-7434)
• 4.7 kΩ @ 1 W (PCI-7433HIR)
• 156 mm x 106 mm (6.08" x 4.13") (PCI-7434P)
■
Isolation voltage: 2500 VRMS: PCI-7432/7432HIR/
7433/7433HIR
5000 VRMS: cPCI-7432/7433
■
Interrupt sources: digital input channel 0 & 1
■
Data transfers: programmed I/O
Isolated Digital Output
■
Number of channels
(PICMG 2.0 R2.1) (cPCI-7432/7433/7434)
• 64 (PCI-7434, cPCI-7434)
■
32-CH isolated digital inputs & 32-CH isolated digital outputs ■
Output type: open collector Darlington transistor
■
Sink current (PCI-7432/7432HIR/7434, cPCI-7434)
• 32 (PCI-7432/7432HIR, cPCI-7432)
(PCI-7432/7432HIR, cPCI-7432)
■
64-CH isolated digital inputs
• 500 mA for single channel @ 100% duty cycle
(PCI-7433/7433HIR, cPCI-7433)
• 500 mA for all channels @ 20% duty cycle
■
64-CH isolated digital outputs
(PCI-7434, cPCI-7434/7434P)
• 500 mA for single channel @ 100% duty cycle
■
Isolation Voltage:
• 2500 VRMS: PCI-7432/7433/7434
• 260 mA for all channels @ 10% duty
Isolated input voltage up to 24 V
■
■
Source current (cPCI-7434P)
Power dissipation: Max. 2.25 W per chip
(8 DO channels) (PCI-7432/7432HIR/7434,
cPCI-7432/7434)
Max. 1.47 W per chip (8 DO channels)
(PCI-7432/7433, cPCI-7432/7433)
■
Isolated input voltage up to 50 V (PCI-7432HIR/7433HIR)
(cPCI-7434P)
Two external interrupt sources (PCI-7432/7432HIR/7433/
■
Supply voltage: 5-35 V
7433HIR, cPCI-7432/7432RP/7433)
■
Isolation voltage: 2500 VRMS
■
Data transfers: programmed I/O
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-41 www.adlinktech.com
(PCI-7432 & PCI-7432HIR)
• 175 mm x 107 mm (6.82" x 4.17")
3U Eurocard form factor, CompactPCI compliant
■
(not including connectors)
• 2.4 kΩ @ 0.5 W (PCI-7432, cPCI-7432, cPCI-7433)
■
• 5000 VRMS: cPCI-7432/7433/7434/7434P
560 mA typical
• 2.4 kΩ @ 1 W (PCI-7433)
Supports a 32-Bit 5 V PCI bus (PCI-7432/7433/7434)
Sink current up to 500 mA on single isolated output
PCI-7434, cPCI-7434P
• Input low voltage: 0 V to 1.5 V
■
■
500 mA typical
• 156 mm x 106 mm (6.08" x 4.13")
PCI-7432
PCI-7433/7433HIR,
cPCI-7433
■Dimensions
Features
+5 V
530 mA typical
• Input high voltage: 5 V to 24 V
PCI-7434
Device
PCI-7432/7432HIR,
cPCI-7432
General Specifications
■
I/O connector: 100-pin SCSI-II female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
(PCI-7433, PCI-7433HIR)
• 160 mm x 100 mm (6.24" x 3.9") (cPCI-7432/7433/7434)
Terminal Boards & Cables
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (Cables are not included.)
■ACL-102100-1
100-pin SCSI-II cable (mating with AMP-787082-9), 1 M
* For more information on mating cables, please refer to P3-48/49.
Note:
Legacy DIN-502S can be replaced by two DIN-50S-01 and
ACL-10252-1 (100-Pin to two 50-Pin Cable, 1 M)
Ordering Information
■PCI-7432
32-CH Isolated DI & 32-CH Isolated DO Card
■PCI-7432HIR
32-CH Isolated DI & 32-CH Isolated DO Card with High Input Range
■PCI-7433
64-CH Isolated DI Card
■PCI-7433HIR
64-CH Isolated DI Card with High Input Range
■PCI-7434
64-CH Isolated DO Card
■cPCI-7433
64-CH Isolated DI Card
■cPCI-7434
64-CH Isolated DO Card
■cPCI-7434P
64-CH Isolated DO Card with Source Current
Transistor
Digital I/O
PCI/LPCI/LPCIe/cPCI-7230, PCI-7233/7234
32-CH Isolated DIO Cards
CompactPCI
■
■
PCI-7230
Number of channels
• 16 (PCI-7230/LPCI-7230/LPCIe-7230/cPCI-7230)
■
PCI-7234
Maximum input range
• 24 V, non-polarity
PCI-7233
• PCI-7230/PCI-7233/LPCI-7230/LPCIe-7230
■
Digital logic levels
• 0-24 V, non-polarity
- Input high voltage: 5-24 V
LPCIe-7230
-
Input low voltage: 0-1.5 V
■
Input resistance: 1.2 k @ 0.5 W
■
Isolation voltage
• 2500 VRMS (LPCI-7230/LPCIe-7230)
• 5000 VRMS (PCI-7230/PCI-7233/cPCI-7230)
cPCI-7230
■
Interrupt sources
• Digital input channel 0 and 1 (PCI-7230/LPCI-7230/
LPCI-7230/cPCI-7230)
• Change-of-state (PCI-7233)
■
Data transfers: programmed I/O
Isolated Digital Output
LPCI-7230
■
Number of channels
• 32 (PCI-7234)
Features
■
■
Output type: Darlington transistor
■
Sink current
• 500 mA for one channel @ 100% duty
• 370 mA for all channels @ 10% duty
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
(PCI-7230/LPCI-7230/LPCIe-7230)
• 130 mA for all channels @ 50% duty
(PCI-7230/LPCI-7230/LPCIe-7230)
• 500 mA for single channel @ 100% duty (PCI-7234)
• 500 mA for all channels @ 20% duty (PCI-7234)
■
Source current
• 500 mA for one channel @100% duty cycle (PCI-7234P)
• 260 mA for all channels @10% duty cycle (PCI-7234P)
■
Power dissipation
• Max. 1.47 W per chip (8 DO channels)
(PCI-7230/PCI-7234P/LPCI-7230/LPCIe-7230)
• Max. 2.25 W per chip (8 DO channels) (PCI-7234)
■
Supply voltage: 5-35 VDC
■
Isolation voltage: 2500 VRMS
■
Data transfers: programmed I/O
■OS Information
(PCI-7230/LPCI-7230/LPCIe-7230)
General Specifications
■
I/O connector
• PCI-7230/7233/7234/7234P
- 37-pin D-sub female
• PCI-7230/LPCI-7230/cPCI-7230
One 50-pin SCSI-II female
-
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
+5 V @ 180 mA typical
(with internal DC-DC power)
PCI-7234P
+5 V @ 150 mA typical
LPCI-7230
+3.3 V @ 279 mA
LPCIe-7230
+12 V @ 133 mA
cPCI-7230
+5 V @ 270 mA typical
Dimensions (not including connectors)
• 153 mm X 107 mm (5.96" x 4.17") (PCI-7230)
• 158 mm X 107 mm (6.16" x 4.17") (PCI-7233)
• 175 mm x 107 mm (6.82" x 4.17") (PCI-7234 & PCI-7234P)
• 120 mm X 65 mm (4.68" x 2.53") (LPCI-7230)
• 119.9 mm x 68.9 mm (4.67" x 2.68") (LPCIe-7230)
• 160 mm x 100 mm (6.24" x 3.9") (cPCI-7230)
Terminal Boards & Cables
PCI-7230/7233/7234/7234P:
■DIN-37D-01
Terminal Board with One 37-pin D-sub Connector
and DIN-Rail Mounting (Cables are not included.)
■ACLD-9137-01
General-Purpose Terminal Board with One 37-pin D-sub Male Connector
2
3
■ACL-10137-1MM
37-pin D-sub male/male cable, 1 M
LPCI-7230/LPCIe-7230/cPCI-7230:
■DIN-50S-01
Terminal Board with One 50-pin SCSI-II Connector
and DIN-Rail Mounting (Cables are not included.)
■ACL-10250-1
50-pin SCSI-II cable (mating with AMP-787082-5), 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-7230
16-CH Isolated DI & 16-CH Isolated DO Card
■PCI-7233
32-CH Isolated DI Card with inversed input logic
■PCI-7234
32-CH Isolated DO Card
■PCI-7234P
32-CH Isolated DO Card with Source Current Transistor
■LPCI-7230
16-CH Isolated DI & 16-CH Isolated DO Low-Profile PCI Card
■LPCIe-7230
16-CH Isolated DI & 16-CH Isolated DO Low-Profile
PCI Express® Card
■cPCI-7230
16-CH Isolated DI & 16-CH Isolated DO Module
www.adlinktech.com 3-42
4
GPIB & Bus Expansion
Supports a 32-Bit 5 V PCI bus (PCI-7230/7233/7234/7234P)
■ Supports a 32-Bit 3.3 V or 5 V PCI bus (LPCI-7230)
■ x1 lane PCI Express Interface (LPCIe-7230)
■ 3U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R2.1) (cPCI-7230)
■ 16-CH isolated digital inputs & 16-CH isolated digital
outputs (PCI-7230/LPCI-7230/LPCIe-7230/cPCI-7230)
■ 32-CH isolated digital inputs (PCI-7233)
■ 32-CH isolated digital outputs (PCI-7234/7234P)
■ 5000 VRMS optical isolation (PCI-7230 & PCI-7233/cPCI-7230)
■ 2500 VRMS optical isolation (PCI-7234/7234P/LPCI-7230/
LPCIe-7230)
■ Sink current up to 500 mA on single isolated output
■ Two external interrupt sources (PCI-7230/LPCI-7230/
LPCIe-7230/cPCI-7230)
■ Change-of-state interrupt sources (PCI-7233)
®
■ Compact, low-profile PCI/PCI Express size PCB
(LPCI-7230/LPCIe-7230)
+5 V @ 300 mA typical
DAQ
• 16 (PCI-7230/LPCI-7230/LPCIe-7230/cPCI-7230)
(needs external DC power)
Modular Instruments
+5 V @ 150 mA typical
PCI-7233
• 32 (PCI-7233)
PCI-7230
Power Consumption
Device
Isolated Digital Input
Power requirements
PXI/PXIe
Specifications
1
PCI/PCIe-7296/7248, PCI-7224
96/48/24-CH Opto-22 Compatible DIO Cards
Specifications
Terminal Boards
Digital I/O
PCI-7224
PCI-7296
PCI-7248
■ Number of channels
• 96 inputs/outputs (PCI/PCIe-7296)
• 48 inputs/outputs (PCI/PCIe-7248)
• 24 inputs/outputs (PCI-7224)
■ Compatibility: 5 V/TTL
■ Digital logic levels
• Input high voltage: 2-5.25 V
• Input low voltage: 0-0.8 V
• Output high voltage: 2.4 V minimum
• Output low voltage: 0.5 V maximum
■ Output driving capacity
• Source current: 2.6 mA for port A & B, and 15 mA
for port C.
• Sink current: 24 mA
■ Data transfers: programmed I/O
General Specifications
PCIe-7296
PCIe-7248
■ I/O connector
• 50-pin ribbon male x 1 (PCI-7224)
• 50-pin ribbon male x 2 (PCI/PCIe-7248)
• 50-pin ribbon male x 4 (PCI/PCIe-7296)
■
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative humidity: 5% to 95%, non-condensing
■ Power requirements
■
Device
Features
■
Supports a 32-Bit 5 V PCI bus (PCI-7224/7248/7296)
■
x1 PCI Express® interface (PCIe-7248/7296)
■
96-CH digital TTL/DTL inputs/outputs (PCI/PCIe-7296)
■
48-CH digital TTL/DTL inputs/outputs (PCI/PCIe-7248)
■
24-CH digital TTL/DTL inputs/outputs (PCI-7224)
■
Emulates 4/2/1 industry standard 8255 PPI (mode 0)
■
Direct interface with OPTO-22 compatible I/O modules
■
Output status read back
■
Onboard 8254 timer/counter chip
■
One 32-Bit timer for timed interrupt generation
■
One 16-Bit event counter to generate event interrupt
■
Programmable interrupt sources
■
+12 V and +5 V power available on OPTO-22 connectors
■
Onboard resettable fuses for power output protection
■
Compact, half-size PCB
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-43 www.adlinktech.com
Power Consumption
860 mA @ 5 VDC Typical
500 mA @ 5 VDC Typical
330 mA @ 5 VDC Typical
350 mA @ 12 VDC Typical
PCIe-7248
280 mA @ 3.3 VDC Typical
590 mA @ 12 VDC Typical
PCIe-7296
280 mA @ 3.3 VDC Typical
■ Dimensions (not including connectors)
• 148 mm x 102 mm (5.77" x 3.97")
(PCI-7248 and PCI-7224)
• 166 mm x 102 mm (6.55" x 3.97") (PCI-7296)
• 168 mm x 112 mm (6.55" x 4.36") (PCIe-7248/7296)
PCI-7296
PCI-7248
PCI-7224
■TB-24R-01*
Terminal Board with 24-CH Relay Outputs
■TB-24P-01*
Terminal Board with 24-CH Isolated Digital Inputs
■TB-16P8R-01*
Terminal Board with 16-CH Isolated DI & 8-CH
Relay Outputs
■DIN-24R-01*
Terminal Board with 24-CH Relay Outputs
■DIN-24P-01*
Terminal Board with 24-CH Isolated Digital
Inputs and DIN-Rail Mounting
* For more information on mating cables, please refer to
P3-48/49.
Ordering Information
■PCI-7296
96-CH Opto-22 Compatible DIO Card
■PCI-7248
48-CH Opto-22 Compatible DIO Card
■PCI-7224
24-CH Opto-22 Compatible DIO Card
■PCIe-7248
48-CH Opto-22 Compliant PCIe DIO Card
■PCIe-7296
96-CH Opto-22 Compliant PCIe DIO Card
Note:
The PCI-7224 is the 24-CH version of the PCI-7248. The software
drivers of the PCI-7224 are exactly the same as those of the PCI-7248
Digital I/O
cPCI-7248
48-CH DIO & Timer/Counter Cards
CompactPCI
cPCI-7248
3U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R2.1)
■
48-CH digital TTL inputs/outputs
■
Emulates 4/2/1 industry standard 8255 PPI (mode 0)
■
Buffered circuits for higher driving capability
■
Ports are independently configurable as input or output
■
External latch signal available for digital inputs
■
Output status read back
■
Known power-up states
■
Onboard 8254 timer/counter chip
■
1-CH 16-Bit event counter to generate event interrupt
■
1-CH 32-Bit timer to generate watchdog timer interrupt
■
Multiple programmable interrupt sources
■
+12 V and +5 V power available on the connector
■
Onboard resettable fuses for power output protection
■
■
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (Cables are not included.)
■ACL-102100-1
100-pin SCSI-II cable (mating with AMP-787082-9), 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■cPCI-7248
48-CH DIO & Timer/Counter Card
3
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative humidity: 5% to 95%, non-condensing
■ Power requirements
Device
cPCI-7248
2
DAQ
■
Digital I/O
■ Number of channels: 48 inputs/outputs
■ Compatibility: 5 V/TTL
■ Power-on states:
pull-high, pull-low, floating (programmable)
■ Digital logic levels
• Input high voltage: 2-5.25 V
• Input low voltage: 0-0.8 V
• Output high voltage: 2.4 V minimum
• Output low voltage: 0.5 V maximum
■ Output driving capacity
• Source current: 15 mA
• Sink current: 24 mA
■ Data transfers: programmed I/O
Interrupt
■ Interrupt #0 sources
• P1C0
• P1C3
• 16-Bit event counter
■ Interrupt #1 sources
• P2C0
• P2C3
• 32-Bit timer (based on 2 MHz internal clock)
General Specifications
■ I/O connector : One 100-pin SCSI-II female
Modular Instruments
Features
Terminal Boards & Cables
PXI/PXIe
Specifications
1
+5 V
470 mA typical
■ Dimensions (not including connectors)
160 mm x 100 mm (6.24” x 3.9”)
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
4
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
GPIB & Bus Expansion
• AD-Logger, DAQBench, DAQMaster
www.adlinktech.com 3-44
cPCI-7452
128-CH Isolated DI & 128-CH Isolated DO Card
CompactPCI
Specifications
Terminal Boards & Cables
Isolated Digital Input
■DIN-100S-01
■ Number of channels: 128
■ Maximum input range: 24 V, non-polarity
■ Digital logic levels: 0-24 V, non-polarity
• Input high voltage: 5-24 V
• Input low voltage: 0-2 V
■ Input resistance: 2.4 kΩ @ 1/2 W
■ ESD protection CKT switch (Forward)
■ Isolation voltage: 2500 VRMS channel-to-system
■ Interrupt sources: 128 channel Change-of-state
(COS)
■ Data transfer: programmed I/O
Terminal Board with One 100-pin SCSI-II
Connector and DIN-Rail Mounting (Cables are not
included.)
Isolated Digital Output
Features
■
Number of channels: 128
■
Supply voltage: 5-35 V
■
Output type: open collector Darlington transistor
■
Sink current: 500 mA for one channel @ 100% duty
■
6U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R3.0)
■
128-CH isolated digital inputs and 128-CH isolated
■
Isolation voltage: 2500 VRMS channel-to-system
digital outputs
■
Data transfer: programmed I/O
■
Non-polarity digital input range
■
Isolated input voltage up to 28 VDC
■
Output Voltage: +5 V
■
Isolation voltage up to 2500 VRMS
■
Output Current: 100 mA max. (@ 40˚C)
■
Sink current up to 300 mA on each isolated output
■
Interrupt sources: 128-CH DI Change-of- State
■
Output status read back
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
General Specifications
■
• AD-Logger, DAQBench, DAQMaster
3-45 www.adlinktech.com
I/O connector
Two 200-pin dual port VHDCI female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
3.3 V
300 mA typical
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
Isolation +5 V Power Supply
■
+5 V
1.26 A typical
Dimensions (not including connectors)
233.35 mm x 160 mm (9.1” x 6.24”)
■ACL-102150-1
SCSI-100 to MINI SCSI-100 connector, 1 M (cPCI-7452 only)
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■cPCI-7452
128-CH Isolated DI & 128-CH Isolated DO Card
Digital I/O
PCI-7396
96-CH High-Driving DIO Card
1
Terminal Boards & Cables
Digital I/O
Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
Interrupt
■ Interrupt #0 sources
• P1C0
• P1C3
• 16-Bit event counter
• Change-of-state detection on any bit of PPI 1 & PPI 2
■DIN-96DI-01
96-CH Isolated DI Terminal Board with DIN-Rail
Mounting (Cables are not included.)
■DIN-96DO-01
96-CH Isolated DO Terminal Board with DINRail
Mounting (Cables are not included.)
■ACL-102100-1
100-pin SCSI-II cable (mating with AMP-787082-9), 1 M
* For more information on mating cables, please refer to P3-48/49.
Ordering Information
■PCI-7396
96-CH High-Driving DIO Card
■ Interrupt #1 sources
• P2C0
• P2C3
• 32-Bit timer (based on 2 MHz internal clock),
• Change-of-state detection on any bit of PPI 3 & PPI 4
2
3
DAQ
■
Supports a 32-Bit 5 V PCI bus
96-CH digital TTL inputs/outputs (PCI-7396)
High driving up to 48 mA (sink) and 15 mA (source)
Emulates 4/2 industry standard 8255 PPI (mode 0)
Ports are independently configurable as input or output
External latch signal available for digital inputs
Output status read back
Known power-up states
Onboard 8254 timer/counter chip
1-CH 16-Bit event counter for external signal
1-CH 32-Bit timer for timed interrupt generation
Change-of-state (COS) interrupt
Multiple programmable interrupt sources
Compact, half-size PCB
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (Cables are not included.)
Modular Instruments
■ Number of channels
• 96 input/output
■ Compatibility: 5 V/TTL
■ Power-on state: input
■ Digital logic levels
• Input high voltage: 2-5.25 V
• Input low voltage: 0-0.8 V
• Output high voltage: 2.4 V minimum
• Output low voltage: 0.5 V maximum
■ Output driving capacity
• Source current: 15 mA
• Sink current: 48 mA
■ Data transfers: programmed I/O
PXI/PXIe
Specifications
General Specifications
■
I/O connector : One 100-pin SCSI-II female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative humidity: 5% to 95%, non-condensing
■
Power requirements
Device
+5 V
PCI-7396
450 mA typical
■ Dimensions (not including connectors)
158 mm x 107 mm (6.16” x 4.17”)
4
GPIB & Bus Expansion
www.adlinktech.com 3-46
Timer/Counter
PCI/cPCI-8554
10-CH General Purpose Timer/Counter & 8-CH DIO Cards
CompactPCI
Specifications
PCI-8554
Terminal Boards & Cables
General-Purpose Timer/Counters
■ Number of channels: 10
■ Counter width: 16 Bit
■ Compatibility: 5 V/TTL
■ Base clock available: 8 MHz or external clock up to 10 MHz
■ Programmable clock sources
• cascaded 32-Bit timer output
• external clock
• timer/counter output of the last channel
• Onboard 8 MHz clock
Cascaded Timer
■
Number of channels: 1
Counter width: 32 Bit
■ Compatibility: 5 V/TTL
■ Base clock available: 8 MHz, fixed
Features
■
■
■
■
■
■
■
■
■
■
■
■
Supports a 32-Bit 5 V PCI bus (PCI-8554)
3U Eurocard form factor, CompactPCI compliant
(PICMG 2.0 R3.0) (cPCI-8554)
Onboard four 8254 programmable timer/counter chips
10-CH independent 16-Bit down counters
1-CH 32-Bit cascaded timer
Onboard 8 MHz clock source
Four programmable clock sources for each timer/counter
Programmable de-bounce filters for external clock &
external interrupt inputs
Programmable interrupt sources
8-CH TTL digital inputs & 8-CH TTL digital outputs
+12 V and +5 V power available on the connector
Onboard resettable fuses for power output protection
■OS Information
• Windows XP, Windows 7/8 x64/x86, Linux
■Software Compatibility
• LabVIEW, MATLAB, Visual Studio.NET
■Software Recommendations
• AD-Logger, DAQBench, DAQMaster
3-47 www.adlinktech.com
Note:
Legacy DIN-502S can be replaced by two DIN-50S-01
and ACL-10252-1 (100-Pin to two 50-Pin Cable, 1 M)
Ordering Information
■PCI-8554
10-CH General Purpose Timer/Counter & 8-CH DIO Card
■cPCI-8554
12-CH 16-Bit Timer/Counter & Digital I/O Card
■
Programmable De-bounce Filters for External Clocks
cPCI-8554
■DIN-100S-01
Terminal Board with One 100-pin SCSI-II Connector and
DIN-Rail Mounting (Cables are not included. For more information about mating cables, please refer to P3-48/49.)
■ Number of channels: 11
■ Filtered inputs: external clock, external interrupt
■ Glitch rejection pulse width: 4 periods of the debounce clock
■ De-bounce clock: up to 2 MHz, programmable
Interrupt
■ Number of interrupt sources: 2
■ Sources: external interrupt input and output of
counter #12
Digital I/O
■ Number of channels: 8 inputs and 8 outputs
■ Compatibility: 5 V/TTL
■ Data transfers: programmed I/O
General Specifications
■
I/O connector: One 100-pin SCSI-II female
■
Operating temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative humidity: 5% to 95%, non-condensing
■ Power requirements
■
Device
+5 V
PCI-8554/cPCI-8554
350 mA typical
■ Dimensions (not including connectors)
134 mm x 107 mm (5.22” x 4.17”) (PCI-8554)
160 mm x 100 mm (6.24” x 3.9”) (cPCI-8554/8554R)
Terminal Boards
Terminal Board & Cable Selection Guide for DAQ
DAQ (Data Acquistion Card)
Type
Terminal Board
Page No.
Model Name
Page No.
DAQ/DAQe/PXI-2000
DAQ/DAQe/PXI-2200
3-18
3-21
DIN-68S-01
DIN-68S-01
3-50
3-50
ACL-10568-1
ACL-10568-1
Terminal Board
Connector Type
68-pin, SCSI-II, Female
68-pin, SCSI-II, Female
PXI-2020/2022
3-19
DIN-68S-01
3-50
ACL-10568-1
68-pin, SCSI-II, Female
DAQ/DAQe/PXI-2208
3-20
DIN-68S-01
3-50
ACL-10568-1
68-pin, SCSI-II, Female
DAQ/DAQe-2213
DAQ/DAQe-2214
3-23
3-23
DIN-68S-01
DIN-68S-01
3-50
3-50
ACL-10568-1
ACL-10568-1
68-pin, SCSI-II, Female
68-pin, SCSI-II, Female
3-22
DIN-68S-01
3-50
ACL-10568-1
68-pin, SCSI-II, Female
3-17
DIN-37D-01
3-50
ACL-10137-1MM
37-pin, D-sub, Female
PCI-9222, PCI-9223
cPCI-9116
3-17
3-28
PCI-9111 Series,
PCI-9112
3-25/26
PCI-9113A
3-27
PCI-9114 Series
3-24
DIN-68S-01
DIN-100S-01
DIN-37D-01
ACLD-9137-01
DIN-20P-01
ACLD-9188-01
ACLD-9182A-01
ACLD-9185-01
DIN-37D-01
ACLD-9137-01
DIN-37D-01
ACLD-9137-01
DIN-20P-01
ACLD-9188-01
DIN-68S-01
3-50
3-50
3-50
3-50
3-50
3-50
3-51
3-51
3-50
3-50
3-50
3-50
3-50
3-50
3-50
ACL-10568-1
ACL-102100-1
ACL-10137-1MM
ACL-10137-1MF
ACL-10120-1
ACL-10120-1
ACL-10120-1
ACL-10120-1
ACL-10137-1MM
ACL-10137-1MF
ACL-10137-1MM
ACL-10137-1MF
ACL-10120-1
ACL-10120-1
ACL-10568-1
68-pin, SCSI-II, Female
100-pin, SCSI-II, Female
37-pin, D-sub, Female
37-pin, D-sub, Male
20-pin, Header
20-pin, Header
20-pin, Header
20-pin, Header
37-pin, D-sub, Female
37-pin, D-sub, Male
37-pin, D-sub, Female
37-pin D-sub, Male
20-pin, Header
20-pin, Header
68-pin, SCSI-II, Female
PCI-6308, PCI-6308A
3-29
PCI/PCIe-7200
3-35
PCI/PCIe-7300A, cPCI-7300
PCIe-7360
PCIe-7350
cPCI-7248
cPCI-7252
cPCI/PCI-7432, 7433, 7434
cPCI-7452
PCI-7230, PCI-7233, PCI-7234(P)
LPCI/LPCIe/cPCI-7230
PCI-7250, PCI-7251
LPCI/LPCIe-7250
PCI-7256
PCI-7258
PCI-7260
3-34
3-32
3-33
3-44
3-37
3-41
3-45
3-42
3-42
3-33
3-33
3-38
3-39
3-36
3-50
ACL-10137-1MF
37-pin, D-sub, Female
3-50
ACL-10137-1MM
37-pin, D-sub, Male
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
3-50
-3-53
3-53
3-53
3-53
3-53
3-50
3-51
3-51
3-50
ACL-10137-1MM
ACL-10137-1MF
ACL-10137-1MF
ACL-10137-1MM
ACL-10137-1MM
ACL-102100-1
ACL-10279
ACL-10279
ACL-102100-1
ACL-10250-1
ACL-102100-1
ACL-102150-1
ACL-10137-1MM
ACL-10250-1
ACL-10137-1MM
ACL-10250-1
ACL-10569-1
ACL-10569-1
ACL-10337 (for JP2/JP3)
ACL-10150
ACL-10150
ACL-10150
ACL-10150
ACL-10150
ACL-102100-1
ACL-102100-1
ACL-102100-1
ACL-10568D, ACL-10568F
37-pin, D-sub, Female
37-pin, D-sub, Male
37-pin, D-sub, Female
37-pin, D-sub, Female
37-pin, D-sub, Female
100-pin, SCSI-II, Female
68-pin, SCSI-VHDCI
68-pin, SCSI-VHDCI
100-pin, SCSI-II, Female
50-pin, SCSI-II, Female
100-pin, SCSI-II, Female
100-pin, SCSI-II, Female
37-pin, D-sub, Female
50-pin, SCSI-II, Female
37-pin, D-sub, Female
50-pin, SCSI-II, Female
68-pin, SCSI-II, Female
68-pin, SCSI-II, Female
-50-pin, Header
50-pin, Header
50-pin, Header
50-pin, Header
50-pin, Header
100-pin, SCSI-II, Female
100-pin, SCSI-II, Female
100-pin, SCSI-II, Female
68-pin, SCSI-II, Female
3-46
PCI-7442, PCI-7443, PCI-7444
3-40
PCI/cPCI-8554
3-47
DIN-100S-01
3-50
ACL-102100-1
100-pin, SCSI-II, Female
PCI-9524
2-20
DIN-68S-01
3-50
ACL-10568-1
68-pin, SCSI-II, Female
HighSpeed DIO
PCI-7396
DIN-37D-01
ACLD-9137-01
ACLD-9137-01
DIN-37D-01
ACLD-9137F-01
DIN-100S-01
DIN-68H-01
DIN-68H-01
DIN-100S-01
DIN-50S-01
DIN-100S-01
DIN-100S-01
DIN-37D-01
DIN-50S-01
DIN-37D-01
DIN-50S-01
DIN-68S-01
DIN-68S-01
-TB-24R-01
TB-24P-01
TB-16P8R-01
DIN-24R-01
DIN-24P-01
DIN-100S-01
DIN-96DI-01
DIN-96DO-01
DIN-68S-01
Digital I/O
PCI-7224, PCI/ PCIe-7248,
PCI/PCIe-7296
3-43
www.adlinktech.com 3-48
3
4
GPIB & Bus Expansion
ACLD-9137-01
DIN-37D-01
DAQ
3-31
High-Resolution
Module
3-30
Timer/
Counter
Analog
Output
PCI-6202
PCI/PCIe/cPCI-6208,
PCI/PCIe/cPCI-6216
2
Modular Instruments
Multi-function DAQ
DAQ/DAQe/PXI-2500
PCI-9221
1
PXI/PXIe
High-Performance DAQ
Model Name
Mating Cable
Cable
Terminal Board
Cable Connector Type
Terminal Board Options
Model Name
Page No.
ACLD-9137-01
3-50
ACLD-9137F-01
3-50
ACLD-9138-01
3-50
ACLD-9182A-01
3-52
ACLD-9185-01
3-52
ACLD-9188-01
3-50
ACLD-9881-01
3-50
DIN-20P-01
3-50
DIN-24P-01
3-53
DIN-24R-01
3-53
DIN-37D-01
3-50
DIN-50P-01
3-50
DIN-50S-01
ACL-10120-1
ACL-10220-1
ACL10568-1
(male/
male)
ACL10250-1
(male/
male)
ACL-10279
(male/
male)
ACL102100-1
(male/
male)
ACL-101371MM (male/
male)
ACL-101371MF (male/
female)
ACL-10150
(female/
female)
ACL10237-1
(male/
male)
ACL-10262
(male/female)
20-pin
Flat Cable
68-pin
SCSIVHDCI to
SCSI-II
50-pin
SCSI-II
68-pin
SCSIVHDCI
50 Ω
100-pin
SCSI-II
37-pin
D-sub
37-pin
D-sub
50-pin
Flat Cable
37-pin
D-sub
62-pin
D-sub
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
3-55/56
•
•
•
•
•
•
•
•
•
•
•
•
•
3-50
DIN-68S-01
3-50
DIN-68H-01
3-50
DIN-96DI-01
3-51
DIN-96DO-01
3-51
DIN-100S-01
3-50
TB-16P8R-01
3-54
TB-24P-01
3-53
TB-24R-01
3-53
TB-6201-01
3-50
TB-6221-01
3-50
TB-6231-01
3-50
•
•
(1)
(2)(3)
•
•
•
•
(4)
•
•
Note:
(1) For PCI-7396 users, please use the ACL-10252 (male/male), 100-pin to two 50-pin cables.
(2) For PCI-7442/PCI-7443/PCI-7444 users, please use the ACL-10568D/ACL-10568F (male/male), 68-pin SCSI-VHDCI cables.
(3) For PCI-7256/PCI-7258 users, please use the ACL-10569 (male/male), 68-pin SCSI-II cable.
(4) For cPCI-7452 users, please use the ACL-102150 (male/male), SCSI-100 to MINI SCSI-100 cable.
3-49 www.adlinktech.com
•
•
•
Terminal Boards
General Purpose Terminal Boards
DIN Rail Screw Terminal BoardsACLD Screw Terminal Boards
• Universal screw terminal boards for easy wiring
• DIN socket for easy mounting in DIN-rail
DIN-100S-01
DIN-68S-01
DIN-50S-01
Terminal Board with One 100-pin SCSI-II
Connector and DIN-rail Mounting
Terminal Board with One 68-pin SCSI-II
Connector and DIN-rail Mounting
Terminal Board with One 50-pin SCSI-II
Connector and DIN-rail Mounting
• On-board Connector Type: 100-pin SCSI-II female
• On-board Connector Type: 68-pin SCSI-II female
• On-board Connector Type: 50-pin SCSI-II female
• Dimensions: 158 mm x 120 mm x 52 mm (W x L x H)
• Dimensions: 103 mm x 85 mm x 46.2 mm (W x L x H)
• Plastic cover for protection of wiring
• Mating Cable:
♦ ACL-102100-1: 100-pin SCSI-II cable, 1 M
• Mating Cables:
♦ ACL-10568-1: 68-pin SCSI-VHDCI cable, 1 M
• Dimensions: 125 mm x 85 mm x 50 mm (W x L x H)
68-pin SCSI-II cable, 1 M
• Mating Cable:
♦ ACL-10250-1: 50-pin SCSI-II cable, 1 M
DIN-37D-01
DIN-20P-01
Terminal Board with One 50-pin Header and
DIN-rail mounting
Terminal Board with One 37-pin D-sub
Connector and DIN-rail Mounting
Terminal Board with One 20-pin Header and
DIN-rail Mounting
• On-board Connector Type: 50-pin header
• On-board Connector Type: 37-pin D-sub female
• On-board Connector Type: 20-pin header
• Dimensions: 103 mm x 85 mm x 43 mm (W x L x H)
• Dimensions: 113 mm x 85 mm x 52 mm (W x L x H)
• Dimensions: 68 mm x 85 mm x 55 mm (W x L x H)
• Mating Cable:
♦ ACL-10150: 50-pin flat cable
• Mating Cable:
♦ ACL-10137-1MM: 37-pin D-sub male/male cable, 1 M
• Mating Cable:
♦ ACL-10120-1: 20-pin flat cable, 1 M
DIN-68H-01
ACLD-9881-01
ACLD-9188-01
Terminal Board with One 68-pin SCSI-VHDCI
Connector and 0 or 50 Ω Jumper Selectable
Impedance
General Purpose Terminal Board with One 37pin D-sub Connector for PCI-9113A and ACL8113A
General Purpose Terminal Board with Two
Connector Options: Two 20-pin Headers or One
37-pin D-sub Connector
• On-board Connector Type: 68-pin SCSI-VHDCI
• For use with PCI-9113A and ACL-8113
• Dimensions: 103 mm x 85 mm x 43 mm (W x L x H)
• On-board Connector Type: 37-pin D-sub female
• On-board Connector Options: Two 20-pin male headers or one 37-pin D-sub female
• Mating Cable:
♦ ACL-10279: 68-pin SCSI-VHDCI cable with 50 Ω impedance
• Reliable screw clamp termination blocks
• Reliable screw clamp terminal blocks
• Dimensions: 222 mm x 105 mm
• Dimensions: 222 mm x 114 mm
• Mating Cable:
♦ ACL-10137-1MM: 37-pin D-sub male/male cable, 1 M
• Mating Cables:
♦ ACL-10120-1: 20-pin flat cable, 1 M
ACLD-9138-01
General Purpose Terminal Board with One 37-pin
D-sub Connector
• On-board Connector Type: 37-pin D-sub female
• Blank RC circuits for analog input boards
• Reliable screw clamp terminal blocks
• Dimensions: 103 mm x 114 mm
• Mating Cables:
♦ ACL-10237-1: 37-pin D-sub male/male flat cable, 1 M
♦ ACL-10137-1MM:
37-pin D-sub male/male cable, 1 M
20-pin shielded & grounded cable, 1 M
ACLD-9137-01 / ACLD-9137F-01
TB-6201-01 / TB-6221-01 /
TB-6231-01
General Purpose Terminal Board with One 37-pin
D-sub Connector
• ACLD-9137-01: on-board 37-pin D-sub male connector
General Purpose/Multiplexer/Matrix Switch
Terminal Board with One 62-pin D-sub
Connector
• ACLD-9137F-01: on-board 37-pin D-sub female connector
• For use with PXI-7901, PXI-7921, and PXI-7931
• Dimensions: 124 mm x 72 mm
• On-board Connector Type: 62-pin D-sub female
• Mating Cables:
♦ ACL-10137-1MM: 37-pin D-sub male/male cable,
• Dimensions: 105.81 mm x 230 mm
1 M (for ACLD-9137F-01)
♦
• Mating Cable:
♦ ACL-10262: 62-pin D-sub male/male cable, 1 M
ACL-10137-1MF: 37-pin D-sub male/female cable, 1 M (for ACLD-9137-01)
www.adlinktech.com 3-50
4
GPIB & Bus Expansion
♦ ACL-10220-1:
3
DAQ
DIN-50P-01
2
Modular Instruments
♦ ACL-10569-1:
1
PXI/PXIe
• Low-cost universal screw terminal boards
• Blank pads accommodate applications such as break detection, low-pass filter, current shunt and voltage attenuator on ACLD-9881-01, ACLD-9188-01, and ACLD-9138-01
• Table-top mounting using nylon standoffs
DIN-96DI-01
96-CH Isolated DI Terminal Board with DIN-Rail Mounting
Specifications
Ordering Information
■ Number of Channels: 96
■DIN-96DI-01
96-CH isolated DI terminal board with
DIN-rail mounting
■
Maximum Input Range: 24 V
■
Digital Logic Levels
• 0 to 24 V non-polarity
Features
♦ Input high voltage: 10 V to 24 V
♦ Input low voltage: 0 to 24 V
■
Input Resistance: 4.7 kΩ @ 0.5 W
■
Isolation Voltage: 2500 VRMS
■
I/O Connector: 100-pin SCSI-II female
■
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
96-CH isolated digital inputs
■
Relative Humidity: 5% to 95%, non-condensing
■
For use with PCI-7396
■
Power Consumption:
■
Isolated input voltage up to 24 V
■
2500 VRMS optical isolation
■
Screw terminals for easy field wiring
■Accessory
• Cabling
ACL-102100-1: 100-pin SCSI-II cable, 1 M
Contact your sales representative for cable length options.
+5 V
48 mA maximum
■
Dimensions: 226 mm (W) x 121 mm (L) x 48 mm (H) (8.81” x 4.71” x 1.87”)
DIN-96DO-01
96-CH Isolated DO Terminal Board with DIN-Rail Mounting
Ordering Information
Specifications
■ Number of Channels: 96
■
Output Type: open collector Darlington transistor
■
Sink Current
• Max. 500 mA for only one Darlington pair
• 500 mA for all Darlington pair @ 20% duty
■
Power Dissipation: Max. 2.25 W per chip
(8 DO channels)
Features
■
96-CH isolated digital outputs
For use with PCI-7396
■ Sink current up to 500 mA on each isolated output
■ 2500 VRMS optical isolation
■ Screw terminals for easy field wiring
■
■
Supply Voltage: 5 VDC to 35 VDC
■
Isolation Voltage: 2500 VRMS
■
I/O Connector: 100-pin SCSI-II female
■
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative Humidity: 5% to 95%, non-condensing
■
Power Consumption:
+5 V
102 mA maximum
■
Dimensions: 226 mm (W) x 121 mm (L) x 48 mm (H) (8.81” x 4.71” x 1.87”)
3-51 www.adlinktech.com
■Accessory
• Cabling
ACL-102100-1: 100-pin SCSI-II cable, 1 M
Contact your sales representative for cable length options.
■DIN-96DO-01
96-CH isolated DO terminal board with
DIN-rail mounting
Terminal Boards
ACLD-9182A-01
Terminal Board with 16-CH Isolated Digital Inputs
1
■
Isolated Digital Input
■ACLD-9182A-01
Terminal board with 16-CH isolated digital
inputs
• Number of Channels: 16
• Maximum Input Range: 24 V, non-polarity
• Digital Logic Levels
■
■
■
■
■
■
■
■
* Input High Voltage: 5 to 24 V
* Input Low Voltage: 0 to 0.7 V
♦ Input Resistance: 560 Ω @ 1 W
♦ Isolation Voltage: 2500 VRMS
■
I/O Connector: 20-pin ribbon male
■
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
16-CH opto-isolated digital inputs
For use with 20-pin ribbon digital input connector of NuDAQ cards
Non-polarity digital input range
Isolated input voltage up to 24 V
5000 VRMS optical isolation
Jumper configurable for voltage input or dry-contact input mode
LED indicator for input status
Screw terminals for easy field wiring
Contact your sales representative for cable length options.
2
Modular Instruments
Features
■Accessories
• Cabling
ACL-10120-1: 20-pin flat cable, 1 M
ACL-10220-1: 20-pin shielded and grounded cable, 1 M
♦ 0 to 24 V, non-polarity
PXI/PXIe
Ordering Information
Specifications
■ Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■ Relative Humidity: 5% to 95%, non-condensing
■ Dimensions: 205 mm x 114 mm (7.99” x 4.44”)
3
DAQ
ACLD-9185-01
Terminal Board with 16-CH Relay Outputs
Specifications
■
Relay Output
• Number of Channels: 16
• Relay Type: SPDT (Form C)
• Isolation Voltage: 1500 VRMS
• Contact Rating
♦ AC: 120 V @ 0.5 A
♦ DC: 24 V @ 1 A
• Breakdown Voltage: 1000 VRMS
• Contact Resistance: 100 mΩ
• Relay ON/OFF time
Features
■
16-CH single-pole, double-throw (SPDT form C) relay outputs
■
For use with 20-pin digital input connector of NuDAQ cards
■
Maximum switching voltage up to 60 VDC/120 VAC
■
Maximum switching current up to 1 ADC/AC
■
Onboard relay driver circuitry
■
LED indicators for relay status
■
Screw terminals for easy field wiring
♦ Operate Time: 6 ms
♦ Release Time: 3 ms
• LED Indicators for Relay Status: one per channel
• Expected Life:
■
■
■
Relative Humidity: 5% to 95%, non-condensing
Power Consumption:
+5 V
+12 V
200 mA maximum
528 mA maximum
Dimensions: 205 mm x 114 mm (7.99” x 4.44”)
Ordering Information
■DIN-96DO-01
96-CH isolated DO terminal board with
DIN-rail mounting
■Accessory
• Cabling
ACL-102100-1: 100-p in SCSI-II cable, 1 M
Contact your sales representative for cable length options.
♦ > 5 x 105 operations @ 1 A, 24 VDC
♦ > 2 x 105 operations @ 0.5 A, 120 VAC
■ I/O Connector: 20-pin ribbon male
■
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
www.adlinktech.com 3-52
4
GPIB & Bus Expansion
DIN-24R-01, TB-24R-01
Terminal Boards with 24-CH Relay Outputs
Features
■
■
■
■
DIN-24R-01
■
■
■
■
■
TB-24R-01
Introduction
The DIN-24R-01 and TB-24R-01 relay output boards are
designed for industrial control applications. It contains 24
electro-mechanical SPDT relays that can be driven by the
24-Bit digital output ports of the PCI-7224, PCI-7248, PCI7296, ACL-7112, ACL-7124, PET-48DIO, and ND-6058.
Each relay's switching capacity is 60 W, 125 VAC The normally
closed, and common contacts for each relay are made available
for maximum flexibility.
24-CH single-pole, double-throw (SPDT form C) relay outputs
50-pin Opto-22 compatible connector
Maximum switching voltage 220 VDC/250 VAC
Maximum switching current up to 2 ADC/AC
LED indicator for relay status
Onboard relay driver circuitry
Screw terminals for easy filed wiring
DIN socket available on DIN-24R-01
50-pin SCSI-type connector available on DIN-24R-01 to
interface with ND-6058
Specifications
■
Relay Output
• Number of channels: 24
• Relay Type: SPDT (Form C)
• Contact Rating
♦ AC: 125 V @ 0.6 A
♦ DC: 30 V @ 2 A
• Breakdown Voltage: 1500 VRMS
• Contact Resistance: 50 mΩ
• Relay ON/OFF Time
♦ Operate time: 3 ms
♦ Release time: 3 ms
• LED Indicators for Relay Status: per channel
• Expected Life: 5 x 105 operations @ 2 A, 30 VDC
• External Coil Excitation Voltage:
♦ 12 V nominal, 19.2 V maximum
(TB-24R/12-01 & DIN-24R/12-01)
♦ 24 V nominal, 38.5 V maximum
(TB-24R/24-01 &DIN-24R/24-01)
■
■
■
■
■
I/O Connector
• 50-pin ribbon male
• 50-pin SCSI-II female
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
Relative Humidity: 5% to 95%, non-condensing
Power Consumption:
+12 V
TB-24R/12-01
DIN-24R/12-01
TB-24R/24-01
DIN-24R/24-01
■
+24 V
288 mA
maximum
-
-
44 mA
maximum
Dimensions
• TB-24R-01: 220 mm (W) x 132 mm (L) x 15 mm (H) (8.58” x 5.14” x 0.58”)
• DIN-24R-01: 203 mm (W) x 120 mm (L) x 55 mm (H) (7.91” x 4.68” x 2.14”)
Ordering Information
■TB-24R/12-01
Terminal board with 24-CH relay outputs @ 12 V coil voltage
■TB-24R/24-01
Terminal board with 24-CH relay outputs @ 24 V coil voltage
■DIN-24R/12-01
Terminal board with 24-CH relay outputs @ 12 V coil voltage and DIN-rail mounting
■DIN-24R/24-01
Terminal board with 24-CH relay outputs @ 24 V coil voltage and DIN-rail mounting
■Accessory
• Cabling
ACL-10150-: 50-pin flat cable
Contact your sales representative for cable length options.
DIN-24P-01, TB-24P-01
Terminal Boards with 24-CH Opto-Isolated Digital Inputs
Features
■
■
■
DIN-24P-01
■
■
■
■
■
■
■
TB-24P-01
Introduction
The DIN-24P-01 and TB-24P-01 digital input terminal boards
feature high-voltage optoisolation on all input channels.
They provide 24 channels that are accessed through a single
50-pin connector that is standard on the NuDAQ digital I/O
boards, including ACL-7122, ACL-7124, PET-48DIO, PCI-7224,
PCI-7248, PCI-7296 and ND-6058. Each channel's input mode
is configurable via jumper settings.
3-53 www.adlinktech.com
24-CH opto-isolated digital inputs
■ I/O Connector
50-pin opto-22 compatible connector
• 50-pin ribbon male
Non-polarity digital input range
• 50-pin SCSI-II female
■ Operating Temperature: 0˚C to 60˚C (32℉ to 140℉)
Isolated input voltage up to 24 V
■ Storage Temperature: -20˚C to 80˚C (-4℉ to 176℉)
5000 VRMS optical isolation
■ Relative Humidity: 5% to 95%, non-condensing
Jumper configurable for voltage input or dry-contact input mode ■ Power Requirement:
LED indicator for input status
+5 V
Screw terminals for easy field wiring
40 mA maximum
DIN socket is available on DIN-24P-01
■ Dimensions
50-pin SCSI-type connector available on DIN-24P-01 to interface • TB-24P-01: 220 mm (W) x 132 mm (L) x 23 mm (H) (8.58" x 5.14" x 0.89")
with ND-6058
• DIN-24P-01: 259 mm (W) x 121 mm (L) x 55 mm (H) (10.1" x 4.71" x 2.14")
Specifications
■
■
Input Modes
• Voltage input
• Dry contact input
Isolated Digital Input
• Number of channels: 24, maximum
• Maximum input range: 24 V, non-polarity
• Digital logic levels
♦ 0 to 24 V, non-polarity
* Input high voltage: 5 V to 24 V
* Input low voltage: 0 to +1.5 V
• Input resistance:1.2 kΩ @ 0.5 W
• Isolation voltage: 5000 VRMS
■ Dry Contact Input
• Number of channels: 24
• Internal pull-up voltage supply: +5 VDC
■ LED Indicators for Input Status: one per channel
Ordering Information
■TB-24P/24-01
Terminal Board with 24-CH isolated digital inputs
■DIN-24P-01
Terminal Board with 24-CH isolated digital inputs and DIN-rail mounting
■Accessory
• Cabling
ACL-10150: 50-pin flat cable
Contact your sales representative for cable length options.
Terminal Boards
TB-16P8R-01
Terminal Board with 16-CH Isolated DI & 8-CH Relay Outputs
1
■
Number of Isolated DI Channels: 16
■
Number of Relay Output Channels: 8
■
LED Indicators for Input and Output Status:
one per channel
■
Electronics Characteristics of Isolated DI:
refer to the TB-24P-01's specifications
■
Electronics Characteristics of Relay Outputs:
refer to the TB-24R-01's specifications
■
■
■
■
■
■
■
■
■
■
■
16-CH isolated digital inputs
Non-polarity digital input range
Isolated input voltage up to 24 V
5000 VRMS optical isolation
Jumper configurable for voltage input or dry contact input mode
8-CH single-pole double-throw (SPDT form C) relays
Maximum switching voltage 220 VDC/250 VAC
Maximum switching current up to 2 ADC/AC
Onboard relay driver circuitry
LED indicators for both input and relay status
Screw terminals for easy field wiring
■TB-16P8R/12-01
Terminal board with 16-CH isolated DI &
8-CH relay outputs
■TB-16P8R/24-01
Terminal board with 16-CH isolated DI &
8-CH relay outputs
■Accessory
• Mating Cable
ACL-10150: 50-pin flat cable
■
I/O Connector: 50-pin ribbon male
■
Operating Temperature: 0˚C to 60˚C (32˚F to 140˚F)
■
Storage Temperature: -20˚C to 80˚C (-4˚F to 176˚F)
■
Relative Humidity: 5% to 95%, non-condensing
■
Power Requirements:
■
+5 V
+12 V
40 mA maximum
100 mA maximum
2
Contact your sales representative for cable length options.
Dimensions: 220 mm (W) x 132 mm (L) x 22 mm (H) Modular Instruments
Features
PXI/PXIe
Ordering Information
Specifications
(8.58” x 5.14” x 0.85”)
3
DAQ
3U to 6U PXI/CompactPCI Adapter
Introduction
Order additional adapter kits to convert 3U PXI/CompactPCI cards to 6U size to fit in with
6U PXI/CompactPCI systems.
■SCSI-100/6U Panel w/FRP
6U adapter for 3U DAQ/DIO PXI/CompactPCI cards with 100-pin SCSI-II connector
• Compliant with cPCI-9116 series, cPCI-7300, cPCI-7432/7433/7434, cPCI-7248, and cPCI-8554 series
■DB-37/62 6U Panel w/FRP
6U adapter for 3U DAQ/DIO PXI/CompactPCI cards with 37-pin/62-pin D-Sub connector
• Compliant with cPCI-6208/6216 series, cPCI-7230, and cPCI-7252
■PXI-22XX 6U/Panel w/FRP
6U adapter for 3U PXI-22XX cards with dual 68-pin SCSI-VHDCI connectors
• Compliant with PXI-2200 series, and PXI-2208
www.adlinktech.com 3-54
GPIB & Bus Expansion
Ordering Information
4
Cable Accessories
ACL-10568-1
ACL-10250-1
68-pin SCSI-VHDCI cable
50-pin SCSI-II cable
(mating with AMP-787082-5), 1 M
(mating with AMP-787082-7), 1 M
ACL-10569-1
ACL-10137-1MM
68-pin SCSI-II cable
37-pin D-sub male/male cable, 1 M
(mating with AMP-787082-7), 1 M
ACL-102100-1
ACL-10137-1MF
100-pin SCSI-II cable
37-pin D-sub male/female cable, 1 M
(mating with AMP-787082-9), 1 M
ACL-10120-1
ACL-10232
20-pin flat cable, 1 M
9-pin D-sub (RS-232) male/female cable, 5 M
ACL-10150
ACL-105100
50-pin flat cable
100-pin SCSI-II assembly
ACL-10237-1 (male/male)
ACL-10537
37-pin D-sub male/male flat cable, 1 M
37-pin D-sub assembly
ACL-10262
ACL-10550
62-pin D-sub male/female cable, 1 M
50-pin SCSI-II assembly
3-55 www.adlinktech.com
Cable Accessories
ACL-10568F-1
ACL-10568D-1
68-pin SCSI-VHDCI flat cable, 1 M
Dual-68-pin head to two 68-pin SCSI-VHDCI cable,
(for PCI-7442, PCI-7443, and PCI-7444)
1M
1
(for PCI-7442, PCI-7443, and PCI-7444)
PXI/PXIe
ACL-IEEE488-1/2/4/8
20-pin shielded & grounded cable, 1 M
IEEE 488 standard cable, 1/2/4/8 M
ACL-10252-1
ACL-PCIEXT-2/5/10
100-pin to two 50-pin cable, 1 M
Extension cable, 2/5/10 M
(for DIN-502S)
(for PCIS-8580-4S/13S)
ACL-10279
ACL-PXIES-2
68-pin SCSI-VHDCI cable with 50 Ω impedance
Copper cable kit, 2 M
2
Modular Instruments
ACL-10220-1
(for PCI-8570 and PXI-8570)
3
DAQ
ACL-102150-1
ACL-SSI-2/3/4
SCSI-100 to MINI SCSI-100 connector, 1 M
SSI bus cable for 2/3/4 devices
(for cPCI-7452 only)
SMB-BNC-1M
Two 20-Pin header to 37-Pin D-sub PC back panel
SMB to BNC cable, 1 M
ACL-10437
SMB-SMB-1M
40-pin header to 37-pin D-sub PC back panel
SMB to SMB cable, 1 M
4
GPIB & Bus Expansion
ACL-10337
(for ACL-7225 and PCI/PCIe-7200)
USB-2M-L
ACL-EXPRESS-1/3/7
2 M USB Type A to USB Mini-B
Expansion Cable, 1/3/7 M
cable with lockable connector
(for PCES-8581-4L/4S/13S)
www.adlinktech.com 3-56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising