Dimplex CAL075 Electric Heater User Manual

Installation and Operating Instructions
Calidou Electronic Panel Radiator
Models:
IP24
CAL075 / CAL100 / CAL150 / CAL200
Issue 5 November 2004
Dimensions and Specification
Model
CAL075
CAL100
CAL150
CAL200
Loading
(kW)
0.75
1.0
1.5
2.0
Length (A)
(mm)
455
621
870
1202
Height
(mm)
604
604
604
604
Depth
(mm)
142
142
142
142
X
(mm)
140
300
400
700
Y
(mm)
87
87
226
227
Z
(mm)
228
234
242
275
Weight
(kg)
17
24
33
47
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
•
•
•
•
•
•
•
•
•
•
•
•
•
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electrical shock, and injury to
persons, including the following:
WARNING THE SURFACES OF THIS HEATER CAN BE HOT
Momentary contact with any part of the heater should not cause
injury. However, aged or infirm persons or young children should not
be left unsupervised in the vicinity of the heater unless a suitable
guard is fitted
IMPORTANT – If this heater is installed in a room containing a bath or
shower, it should be so installed that switches and other controls
cannot be touched by a person using a bath or shower – to comply
with this requirement see ‘Lock the Control Cover’ section on page 2.
If you use this heater in conjunction with an external thermal control,
a programme controller, a timer or any other device which switches
the heat on automatically, observe all safety warnings AT ALL TIMES
since a fire risk exists when the heater is accidentally covered or
displaced
The installation of this product should be carried out by an electrician
or competent person and be in strict accordance with the current IEE
Wiring Regulations and relevant Building Regulations
This heater must not be mounted within 150mm of curtains and other
combustible materials or 100mm from a shelf or overhang
NEVER cover or obstruct in any way the heat outlet slots at the top of
the heater or the air inlet slots at the base of the heater
DO NOT cover the heater – Do not place material or garments on the
heater or obstruct the air circulation around the heater
Before connecting the heater check that the supply voltage is the
same as that stated on the heater
The heater must be installed in accordance with these instructions
The heater must be mounted using the wall bracket supplied. The
heater should only be operated in the upright position
The heater should be positioned in accordance to the clearances
stated in these instructions
DO NOT locate this heater immediately beneath a fixed socket outlet
General
The Calidou radiator is designed to provide exceptional levels
of comfort with a combination of radiant and convected heat
in both domestic and commercial applications.
Wall Mounting / Installation
The heater should be positioned observing the minimum clearances
stated around the heater.
(see also ‘Electrical’ section)
The wall bracket supplied with the heater must be used
1. Using a screwdriver, turn the latch in a clockwise direction to
unlatch the bracket, then remove it from the appliance (see Fig.1)
2. Mount the bracket on the wall using a minimum of 4 screws
(max diameter 6mm) making sure that it is the correct way up and
at the correct height. (see Fig.2)
3. Position the appliance on the bracket.
4. Re-latch the bracket turning the latch anti-clockwise.
Electrical
The wires in the mains lead are coloured in accordance with the following code:
GREEN & YELLOW
EARTH
BLUE
NEUTRAL
BROWN
LIVE
BLACK
PILOT WIRE
Fig.1
Fig. 2
Model
CAL075
CAL100
CAL150
CAL200
A (mm
140
300
400
700
B (mm)
228
234
242
27
If the wall is a light partition or crumbling, then supporting legs
are also needed
(Part No. CAL0001). The heater MUST be fitted to the wall as
well as having the supporting legs
(See also ‘Pilot Wire Connection’)
The heater is fitted with a length of flexible cable for connection to the fixed wiring of the
premises through a suitable connection box positioned adjacent to the heater.
The supply circuit to each heater must incorporate a double pole isolating switch having a
contact separation of at least 3mm
Pilot Wire Connection
The BLACK control wire is designed to carry a signal from slot in or wall mounted Dimplex
programmers. If, however a programmer is not being used, the pilot wire should be isolated in
accordance with the current IEE Wiring Regulations.
IMPORTANT - Do NOT connect the BLACK pilot wire to earth
Care should be taken with the installation of the pilot wire(s) as when switching to background
(set back) they become energised at 240V although only at a current of 1mA.
In every case a suitable means of isolation must be provided for the pilot wire and marked to
indicate that two sources of supply may be present at the heater.
Where pilot wires are installed separately from the heater final sub-circuit they should be
protected, double insulated and carry their own integral earth continuity conductor.
1.
2.
3.
Place the legs under the heater
Position the hinges into the grooves in the air inlet
Unscrew the jacks, until they reach the floor
Operation
Advice on Using your Heater
•
•
•
For greatest economy switch the heater to background (setback) if
you leave the room for long periods of time or before going to bed.
Do not set the comfort level too high. Even small reductions on the
thermostat setting can save a lot of energy.
If you go away for a long period of time select the frost protection
setting on the function dial or reduce the thermostat setting to a lower
level.
Locking the Thermostat Setting (C)
If necessary you can lock the thermostat dial to a single setting or range.
To lock the settings, use a small pair of narrow nosed pliers to pull out the
locking pins at the rear of the thermostat dial.
The following settings can be obtained: (see Fig.4)
•
Mode Selection Dial (A)
Use this rotary dial to select the function you require
Symbol
Function
Frost Protection
Background (set back)
Comfort
Off
Off
Programme
Description
Heater will switch on to provide frost
protection if the room drops below
5ºC
Heater will maintain a lower
temperature level for background
heating (comfort less 3.5ºC)
•
•
•
Single setting – Set thermostat dial to desired setting (eg no.6).
Locate one pin directly opposite the setting required
Minimum setting – Set thermostat dial to desired setting (e.g. no.6).
Locate one pin opposite the setting required and one hole to the left.
(The thermostat will now be adjustable from 6-9 only)
Maximum setting – Set thermostat dial to desired setting (eg
no.6).Locate one pin opposite the setting required and one hole to
the right. (The thermostat dial will now be adjustable from 1-6 only)
Minimum - maximum setting – (e.g. no.2-4) Locate both pins and
space apart until desired range is found
Heater will maintain the temperature
set on the thermostat dial
Heater will not function
Heater will be controlled by a
programming device
Note: If the programme function is selected but no programming device is being
used, the heater will function in comfort mode
The following Dimplex programmers are available:
Pilot Wire Wall Mounted Controller (2 Zone) – Part no. RX010006
MBS Wall Mounted Programmer (2 Zone) – Part no. RX010007
MBS Slot in Receiving Cassette – Part No. RX9913
MBS Slot in Programming Cassette (Single Zone) – Part no. RX9912
Pilot Wire Programming Cassette (Single Zone) – Part no. RX9911
Function Display (B)
Neon indicators adjacent to the function selector will light to show the mode
selected
Setting the Comfort Temperature (C)
Use the thermostat dial (C) to select your desired room temperature. The
To Lock the Control Cover (E)
A screw is provided to permanently lock the cover in position. It is located
on the back of the control box, under the thermostat dial. Remove this and
screw through the notch below the lifting tab into the plastic housing. (see
Fig.4 above)
Safety
A thermal cut-out will switch off the heater if, for any reason, it overheats.
Should the cut-out operate, switch off the mains supply and allow the
heater to cool. Once the heater has cooled sufficiently remove the
obstruction and switch on the mains supply.
Cleaning
markings on the dial are in approximately 3.5ºC increments. The settings are
(Frost Protection) and numbers 1-10 (MAX). The quickest way to find your comfort
setting is to turn the thermostat dial to the maximum setting. When your ideal
comfort level is achieved, turn the thermostat dial down until the thermostat
switches off (the neon light will go out) Leave at this setting and the heater will
automatically maintain the desired temperature.
Before cleaning your heater, switch off the heater and allow it to cool.
Disconnect the electricity supply to the appliance. The outside can be
cleaned by wiping it over with a soft damp cloth and then dried. Do not
use abrasive cleaning powders or furniture polish, as this can damage the
surface finish.
Thermostat Light (D)
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product free of
charge (excluding lamps & subject to availability) provided it has been
installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can quote
the model number, series, date of purchase, and nature of the fault at the
time of your call. The customer services help desk will also be able to
advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this may
result in loss or damage and delay in providing you with a satisfactory
service.
The neon indicator below the thermostat will light when the heater is
operating.
Background (set back)
The background setting is preset at - 3.5ºC this is the amount the room
temperature will be allowed to drop when you switch the function selector
from comfort to background.
Reverting to comfort mode will automatically cause the temperature to rise to
the setting on the thermostat dial.
After Sales Service
Please retain your receipt as proof of purchase.
This appliance complies with European Safety Standard EN 60335-2-30, and European Standards EN 55014, EN 60555-2 and EN60555-3 for
Electromagnetic Compatibility. These standards cover the requirements of the EEC Directives 73/23 and 89/336.
Glen Dimplex UK Ltd
UK Customer Help Line (8am-6pm Mon-Fri; 8:30am-1pm Sat.)
Millbrook House
Customer Services: Tel: (0870) 727 0101
Grange Drive
Fax: (0870) 727 0102
Hedge End
E-mail:customer.services@glendimplex.com
Southampton
Web-site: www.dimplex.co.uk
SO30 2DF
Republic of Ireland
Tel: 01 842 4833