Dimplex DXUFSR2 Fan User Manual

Installation and Operating Instructions
08/35169/0
Model(s) : DXUFSR2
(IP21)
Fan Heater
Dimensions
H
265
(millimetres)
Model(s)
Specification
DXUFSR2
2.0kW Thermostat & Switch
Issue 0
W
230
D
230
(see Fig. 3)
(see Fig. 2)
Fig. 1
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair
type of rugs, or less than 750mm (30") away from any
overhanging surface. Keep combustible materials such as
drapes and other furnishings clear from the front, sides
and rear of the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of a
bath, a shower or a swimming pool.
DO NOT place the heater directly below a fixed socket outlet.
The socket-outlet must be accessible at all times to enable
the mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct the air inlet and outlet openings
in any way.
The heater must be on a flat stable surface when in use.
DO NOT operate the heater with the mains lead overhanging
the front outlet grille.
The appliance is designed to self-right itself if it is
accidentally knocked over, however the appliance should
not be maltreated to perform this function.
ALWAYS ENSURE THE APPLIANCE DOES NOT COME TO REST
ON THE MAINS LEAD OR ALLOW THE LEAD TO BECOME
WRAPPED AROUND THE APPLIANCE - THIS MAY IMPAIR THE
SELF-RIGHT FUNCTION.
NEVER leave the heater unattended when it is used by or
near the aged, infirm person’s or children.
THE HEATER CARRIES THE WARNING SYMBOL INDICATING
THAT IT MUST NOT BE COVERED.
The instruction leaflet belongs to the appliance and must
be kept in a safe place. If changing owners, the leaflet must
be surrendered to the new owner.
IMPORTANT – If the mains lead of this appliance is damaged,
it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard.
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
Electrical connection
This heater must be used on an A.C.~ supply only and the voltage
marked on the heater must correspond to the supply voltage. This
heater is fitted with a plug incorporating a 13 amp fuse. When replacing
the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used.
If the plug is not suitable for the socket outlets in your home, the plug
must be cut off and an appropriate one fitted. A plug cut off from a
mains lead will give a shock hazard if inserted into a 13 amp socket
elsewhere in the house. To avoid this, it should be disposed of
immediately.
NOTE: The fuse cover of a non-rewirable plug must be refitted when
changing the fuse. Should the cover become lost, the plug must not be
used until the correct replacement fuse cover is obtained from your
supplier or by contacting our customer helpline.
IMPORTANT : The wires in this mains lead are coloured in accordance
with the following code :
BLUE :
BROWN :
NEUTRAL
LIVE
As the colours of the wires in the mains lead may not correspond with
the coloured markings in your plug, proceed as follows :
Connect the BROWN wire to the terminal marked ‘L’ or coloured RED.
Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.
Note : ‘L’ or ‘N’ must not be connected to the EARTH terminal marked
‘E’ or
or coloured GREEN or GREEN AND YELLOW.
If in doubt, consult your electrician.
Using the Heater
Heat Control - see Fig. 2
Fig. 2
-
OFF
-
Cool Blow*
-
Half heat
-
Full heat
Thermostat Control - see Fig. 3
Fig. 3
The heat output is controlled by the
thermostat, according to the room
temperature.
Turn the thermostat knob fully clockwise
to maximum setting initially. When the
room is warm enough, reduce the setting
slowly until the heater just clicks off.
The heater will now cycle on and off to maintain your selected room
temperature. An audible click may be heard when the thermostat
operates - this is normal.
Note : If the heater does not come on when the thermostat is at a low
setting, this is normally because the room is warmer than the thermostat
setting and is not a fault.
* When the heat control is set to ‘ ‘ for cool blow, set the thermostat
control to maximum.
Position ‘ ‘ will turn the heater on and off to maintain a temperature of
approximately 5°C.
Safety - overheat protection
After Sales Service
For your safety, this appliance is fitted with a thermal cut-out. In the
event that the product overheats, the cut-out switches the heater off
automatically. To bring the heater back into operation, remove the cause
of overheating, then turn off the electrical supply to the heater for a few
minutes.
When the heater has cooled sufficiently reconnect and switch on the
heater.
If the cut-out operates repeatedly, contact your supplier.
Your product is guaranteed for three years from the date of purchase.
Cleaning
WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powders or polish of any kind
on the heater.
Wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean
off stains. Be careful not to allow moisture into the heater.
Ensure that dust or fluff does not accumulate inside the heater as this
could lead to overheating of the element. Use a vacuum cleaner to remove
any fluff which does accumulate.
Within this period, we undertake to repair or exchange this product free
of charge provided it has been installed and operated in accordance
with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0845 600 5111. It would assist us if you can quote
the model number, series, date of purchase, and nature of the fault at the
time of your call. The customer services help desk will also be able to
advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first
instance as this may result in loss or damage and delay in providing you
with a satisfactory service.
Please retain your receipt as proof of purchase.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or
retailer for recycling advice in your country.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (Autumn–Winter only)
Customer Services:
Tel.
0845 600 5111
Fax.
01489 773053
e-mail customer.services@glendimplex.com
Republic of Ireland
Tel.
01 8424833
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.