Directed Electronics 200 Automobile Alarm User Manual

Model 200
Owner's Guide
Limited Lifetime
Consumer Warranty
Directed Electronics, Inc. ("DEI®") promises to the original purchaser to repair or
replace with a comparable reconditioned model any DEI unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated
sensors and accessories, which proves to be defective in workmanship or material
under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized
DEI dealer; the unit will be professionally reinstalled in the vehicle in which it was
originally installed by an authorized DEI dealer; and the unit is returned to DEI, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase
bearing the following information: consumer's name, telephone number and address;
the authorized dealers name, telephone number and address; complete product
description, including accessories; the year, make and model of the vehicle; vehicle
license number and vehicle identification number. All components other than the
unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of
the same. This warranty is non-transferable and is automatically void if: the original
purchaser has not completed the warranty card and mailed it within ten (10) days of
the date of purchase to the address listed on the card; the unit's date code or serial
number is defaced, missing or altered; the unit has been modified or used in a
manner contrary to its intended purpose; the unit has been damaged by accident,
unreasonable use, neglect, improper service, installation or other causes not arising
out of defects in materials or construction. The warranty does not cover damage to
the unit caused by installation or removal of the unit. DEI, in its sole discretion, will
determine what constitutes excessive damage and may refuse the return of any unit
with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE
EXPRESSLY EXCLUDED; AND DEI NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DEI DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY
FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS
OR INSTALLERS. DEI SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS
AGAINST POSSIBLE THEFT. DEI IS NOT OFFERING A GUARANTEE OR INSURANCE
AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VAN-
© 2001 Directed Electronics, Inc.
i
DALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE,
REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF
ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DEI OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL
APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DEI SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DEI DEALER'S PURCHASE PRICE OF THE UNIT. DEI SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS,
COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO
REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do
not allow limitations on how long an implied warranty will last or the exclusion or
limitation of incidental or consequential damages. This warranty gives you specific
legal rights and you may also have other rights that vary from State to State.
This product is not covered by the Guaranteed Protection Plan (“GPP”). DEI does not
and has not authorized any person or entity to create for it any other obligation,
promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
■
■
■
■
■
■
■
■
■
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2001 Directed Electronics, Inc.
Table of Contents
Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Maintenance . . . . . . . . . . . . . . . . . . . . .
Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Functions . . . . . . . . . . . . . . . . . . . . . .
Standard Configuration . . . . . . . . . . . . . . . . . . . .
Using Your System . . . . . . . . . . . . . . . . . . . . . . . .
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-Level Security Arming . . . . . . . . . . . . . . . . .
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disarming Without a Transmitter . . . . . . . . . . . . . .
Disabling and Re-enabling the Back-Up Battery Siren
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valet® Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nuisance Prevention Circuitry . . . . . . . . . . . . . . . .
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Arming Diagnostics. . . . . . . . . . . . . . . . . . . . . . .
Disarming Diagnostics . . . . . . . . . . . . . . . . . . . . .
Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . .
Code-Hopping™ . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rapid Resume Logic . . . . . . . . . . . . . . . . . . . . . . .
High Frequency . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Saver Mode . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Options . . . . . . . . . . . . . . . . . . . . . .
Security & Convenience Expansions . . . . . . . . . . . .
Glossary Of Terms . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Reference Guide (Removable) . . . . . . . . . . .
© 2001 Directed Electronics, Inc.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
4
4
5
5
6
6
7
8
8
9
10
11
11
12
13
13
14
14
15
15
16
17
18
19
21
1
Standard Configuration
2
© 2001 Directed Electronics, Inc.
What is Included
■
A control module
■
A pair of two-button remote transmitters
■
A Stinger® Doubleguard® dual-output shock sensor (on-board
the control module)
■
A back-up battery siren
■
Two back-up battery siren keys
■
The red status LED indicator light
■
A push-button Valet® switch
■
A mercury tilt switch
■
Failsafe® Starter Kill (on-board the control module)
Important Information
Congratulations on the purchase of your state-of-the-art security
system. This system has been designed to provide years of troublefree operation. This guide should help you to get the most out of
your system, so please take the time to review it thoroughly prior
to using the system.
System Maintenance
The system requires no specific maintenance. Your remote is
powered by a lithium battery that lasts approximately three years
under normal use. The remotes are disposable, so after the battery
© 2001 Directed Electronics, Inc.
3
runs out, you can simply throw the transmitter away and replace
it with a new one.
Your Warranty
Your warranty card must be returned. If the warranty card is not
returned, you do not have a warranty. It is also necessary to keep
your receipt, which reflects that the product was installed by an
authorized dealer. Make sure that you receive the warranty card
from your dealer.
IMPORTANT! This unit and its components are water resistant, not
waterproof; so the warranty is void if the product has been damaged as
a result of prolonged water exposure or submersion.
FCC/ID Notice
This device complies with Part 15 of FCC rules. Operation is subject
to the following conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this device.
4
© 2001 Directed Electronics, Inc.
Transmitter Functions
The receiver uses a computer-based Learn Routine to learn the
transmitter buttons. This makes it possible to assign different
transmitter buttons to different receiver functions. The transmitter
initially comes programmed with Standard Configuration, but may
also be customized by an authorized dealer. The buttons indicated
in the instructions in this manual correspond to a Standard
Configuration transmitter.
Standard Configuration
Button
The arming and panic functions are controlled by
. To arm the
system press this button for one second. To activate the panic
function, press and hold this button for 1.5 seconds.
Button
The disarm function and an optional auxiliary convenience or
expansion function are controlled by
. To disarm the system
press this button for one second. To activate the auxiliary function,
press and hold this button for 1.5 seconds.
This auxiliary output controls _____________________________.
and
Buttons
Another optional auxiliary convenience or expansion function can
be activated by pressing
and
simultaneously.
This auxiliary output controls _____________________________.
© 2001 Directed Electronics, Inc.
5
Using Your System
The transmitter buttons indicated in this guide correspond to the
standard transmitter configuration. Remember, this is not the only
way your transmitter may be set up.
Arming
You can activate, or arm, the system by pressing
on your
transmitter for one second. When the system arms, you will hear a
short siren sound, or chirp, and see the lights flash once.
While the system is armed, the status LED will flash approximately
once per second, showing that the system is actively protecting
your vehicle. If you hear a second chirp after arming and see the
status LED flashing in groups, refer to the Diagnostics section of
this guide. This extra chirp is called Bypass Notification.
The system also can be programmed to arm itself automatically
(called passive arming). If the system is programmed for passive
arming, it will automatically arm 30 seconds after the ignition is
turned off. Whenever the system is in its 30-second passivearming countdown, the status LED will flash twice as fast as it
does when the system is armed. At the 30-second point, the siren
will chirp to indicate that the system is armed.
NOTE: Some faulty zones may prevent the system from passively arming.
(See Arming Diagnostics and Table of Zones sections of this guide.)
Additionally, each time a sensor is triggered during the passive arming
countdown, the 30-second countdown starts over.
6
© 2001 Directed Electronics, Inc.
When armed, your vehicle is protected in the following ways:
■
Light impacts will trigger the Warn Away® signal. When
triggered, the siren will chirp and the parking lights will flash
for a few seconds.
■
Heavy impacts will trigger the system. The full trigger
sequence is 30 or 60 seconds of constant siren and flashing
parking lights.
■
If the tilt switch is triggered or the ignition is turned on while
the system is armed, the full trigger sequence will activate.
■
The starter kill prevents the vehicle’s starter from cranking.
Multi-Level Security Arming
Multi-Level Security is a feature that is only available when using
a Standard Configuration transmitter (see Transmitter Functions
section of this guide). Multi-Level Security Arming allows you to
select which of the security system's inputs or sensors will be
active and which will be bypassed at the time that the system is
armed (see Table of Zones section of this guide). Pressing
again within five seconds of arming the security system will activate the Multi-Level Security Arming feature. Each time
is
pressed again, a different security level is selected. The different
security levels can be selected as follows:
■
Pressing
one time: The siren chirps once. The system is
armed.
■
Pressing
a second time within five seconds: The siren
chirps twice followed by a long chirp. Zone Two is now bypassed.
© 2001 Directed Electronics, Inc.
7
■
Pressing
a third time within five seconds: The siren
chirps three times followed by a long chirp. Zone Four is now
bypassed.
■
Pressing
a fourth time within five seconds: The siren
chirps four times followed by a long chirp. Zones Two and
Four are now bypassed.
■
Pressing
a fifth time within five seconds: The siren
chirps five times followed by a long chirp. All input zones,
except the ignition (Zone 5), are now bypassed.
NOTE: For watercraft, we recommend turning off the shock sensor (Zone
Two) whenever the craft is in the water to avoid false triggers.
NOTE: Multi-Level Security Arming only applies to a single arming cycle.
Once the system is disarmed and then re-armed, all the zones will be
active again.
Disarming
To disarm the system, press
. You will hear two chirps, and the
lights will flash twice. If the siren chirps either four or five times
when disarming, refer to the Diagnostics section of this guide.
This is called Tamper Alert.
Disarming Without a Transmitter
This feature allows you to disarm the system without the transmitter should it be lost, damaged or disabled. In order to disarm
without a transmitter, you must have the ignition key and know
where the Valet® switch is located. Be sure to check with the
installer for the location of the Valet switch.
8
© 2001 Directed Electronics, Inc.
To disarm the security system,
turn the ignition to the "on"
position. Press the Valet switch
the selected number of times (1-5
DRW-35
presses) within 15 seconds. The system should now disarm. If it
does not, you may have waited too long to press the Valet switch;
turn the ignition off and on and try again.
LOCATION OF VALET SWITCH______________________________
IMPORTANT! The unit can be programmed to respond to 1-5 pulses of
the Valet® switch for the disarm function. Be sure to check with the
installer for the desired programming.
Disabling and Re-Enabling the Back-Up Battery Siren
If the vehicle battery has been disconnected or is low on power,
the back-up battery siren will sound.
© 2001 Directed Electronics, Inc.
9
To disable the back-up battery siren, follow these steps:
1.
Locate the back-up battery siren.
2.
Remove the water protective cap on the
back side of the siren to expose the siren
lock switch.
3.
Insert the siren key into the siren lock
switch and turn the key to the LEFT to
disable the back-up battery siren.
Once the vehicle battery has been reconnected or full charge is
restored, the back-up battery siren can be re-enabled.
To re-enable the back-up battery siren, follow these steps:
1.
Turn the siren key back to the RIGHT.
2.
Replace the water protective cap on the
back side of the siren.
WARNING! If the siren lock switch key is turned to
the enable position without the vehicle battery
being connected, the back-up battery siren will
sound.
Panic Mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your transmitter! Just
press
for 1.5 seconds, and you will enter Panic Mode. The
siren will sound and the parking lights will flash for the programmed siren duration. To stop Panic Mode at any time, press
on the remote transmitter again.
10
© 2001 Directed Electronics, Inc.
Valet® Mode
You can prevent your security system from automatically arming
and triggering by using Valet® Mode. This is very useful when
washing or servicing the vehicle. In Valet Mode, the security system will not arm, even with the remote transmitter, but all convenience functions will continue to operate normally.
To enter or exit Valet® Mode with the Valet switch:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
switch within 10 seconds.
DRW-35
The status LED will light solidly if you are entering Valet Mode, and
it will go out if you are exiting Valet Mode.
Nuisance Prevention® Circuitry
Your system has DEI®’s Nuisance Prevention® Circuitry (NPC®). It
prevents annoying repetitive trigger sequences due to faulty sensors or environmental conditions such as thunder, jackhammers,
airport noise, etc. Here’s how it works:
The alarm triggers three times. Each time, the same shock sensor
or switch is triggering the alarm. The three triggers are within 60
minutes of each other. NPC will interpret this pattern of triggers
as false alarms. After the third trigger, NPC ignores, or bypasses,
© 2001 Directed Electronics, Inc.
11
that sensor or switch (along with any other sensors or switches
sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the system while it is being
bypassed, the 60-minute bypass period will start over. This ensures
that a sensor that continually triggers will remain bypassed.
The mercury tilt switch, the optional luggage carrier/saddlebag
protector, and the ignition switch (Zones 1, 3 and 5, see Table of
Zones section) are protected differently by NPC. If any one of these
zones is triggered for three, full 30-second cycles (one and one half
minutes), the system will bypass the zone until the trigger ceases.
NOTE: Arming and disarming the system does not reset this function!
The only ways to reset a bypassed zone are for it to not trigger for 60
minutes, or to turn on the ignition. If testing your system, it is
important to remember that the NPC programming can cause zones to be
bypassed and appear to stop working. If five chirps are heard when disarming, NPC has been engaged. If you wish to clear the NPC™
memory, turn the ignition key on.
Diagnostics
The microprocessor at the heart of your security system is
constantly monitoring all of the switches and sensors that are
connected to it. It detects any faulty switches and sensors and
prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during
your absence.
12
© 2001 Directed Electronics, Inc.
Arming Diagnostics
If the security system is armed while an input is active (a sensor
is triggering) the siren will chirp once when arming and then one
more time a few seconds later. This extra chirp is called Bypass
Notification.
The security system will ignore the input that was active when the
system was armed, until the input goes away. Three seconds later
the system will monitor that input normally. For example, if the
tilt switch (motorcycles only) is at an unusual angle, and you try
to arm the security system, you may hear Bypass Notification
chirps. Once the tilt switch is restored to its proper angle, the
vehicle will be monitored normally.
NOTE: Bypass Notification will not occur if the chirps have been programmed OFF.
Disarming Diagnostics
Extra disarm chirps are the Tamper Alert. If four chirps are heard
when disarming, the system was triggered in your absence. If five
chirps are heard, a zone was triggered so many times that Nuisance Prevention® Circuitry has bypassed that zone. In either case,
the status LED will indicate which zone was involved (see the
Table of Zones section). The security system will retain this information in its memory, and continue to chirp four or five times
each time it is disarmed, until the next time the ignition key is
turned on.
© 2001 Directed Electronics, Inc.
13
Table of Zones
The zone number is the number of LED flashes used by the
security system to identify a specific input. The standard input
assignments are listed in the following Table of Zones, along
with spaces to write in any optional sensors or switches you have
had installed.
ZONE
(Number of
LED Flashes)
DESCRIPTION
DEALER-INSTALLED
OPTIONS
1
Instant trigger - used for
the mercury tilt switch
2
Impact detected by the
Double Guard® Shock Sensor
3
Instant trigger - optional closed loop
trigger for saddlebags or luggage carrier
4
Optional sensors
5
Ignition trigger
If the Warn Away® response is triggered, the LED will not report it.
Code-Hopping ®
The receiver and transmitters each use a mathematical formula
called an algorithm to change their code each time the transmitter
is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should
be. This helps to keep the transmitter "in sync" with the control
unit even if you use the remote control out of range of the vehicle.
14
© 2001 Directed Electronics, Inc.
However, if the transmitter buttons have been pressed many times
out of range of the vehicle, or the battery has been removed, it
may get out of sync with the control unit and fail to operate the
system. To re-sync the remote control simply press
on the
transmitter several times within range of the receiver. The alarm
will automatically re-sync and respond to the transmitters normally.
Rapid Resume Logic
This DEI® system will store its current state to non-volatile
memory. If power is lost and then reconnected the system will
recall the stored state from memory. This means if the unit is in
Valet® Mode and the battery is disconnected for any reason, such
as for a service visit, when the battery is reconnected the unit will
still be in Valet Mode. This applies to all states of the system
including arm, disarm, and Valet Mode.
High Frequency
Your system transmits and receives at 434 MHz. This provides a
cleaner spectrum with less interference and a more stable signal.
Enjoy a phenomenal increase in range – even in areas with high
radio interference.
© 2001 Directed Electronics, Inc.
15
Power Saver Mode
Your system will automatically enter Power Saver Mode while
armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the
vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions:
■
Power Saver when the system is armed: After the system has
been armed for 24 hours, the LED will flash at half its normal
rate, decreasing the system's current draw.
■
Power Saver in Valet Mode: When the system enters Valet
Mode the LED illuminates steadily. If the vehicle is not used
(ignition is not turned on) for a period of one hour while the
system is in Valet Mode, the LED will shut off. If the system
remains in Valet Mode, the LED will come back on the next
time the ignition is turned on and then back off.
16
© 2001 Directed Electronics, Inc.
Programming Options
Programming options control what your system does during
normal operation, and require few or no additional parts. However,
some programming options may require additional installation
labor.
The following is a list of the program settings, with the factory
settings in Bold:
■
Active arming (only with the transmitter) or passive arming
(automatic arming 30 seconds after the ignition is turned
off).
■
Arming/disarming confirmation siren chirps on or off.
■
Siren duration can be programmed for either 30 or 60
seconds.
■
Siren output can be programmed for constant or pulsed
output when the system is triggered.
■
Valet pulse count: The number of presses of the Valet® switch
required to disarm the security system can be programmed
from 1-5 presses. The default setting is one press.
© 2001 Directed Electronics, Inc.
17
Security & Convenience
Expansions
Here we have listed only some of the many expansion options
available. Please contact your dealer for a complete explanation of
all the options available to you.
Backup Battery: The 520T keeps the system armed, triggers the
alarm and keeps the starter kill active if main battery power is disconnected.
Headlight and Parking Light Automation: The 545T Nite-Lite®
will automatically turn on your parking and headlights when it
gets dark. A transmitter function can also be used to turn on your
parking and headlights for a programmed time.
820M Valet® Car★Com™: The 820M Valet® Car★Com™ is a one-way
pager system that can be added to any compatible DEI security
system. Using the 820M, many of the security and convenience
features of your DEI security system can be operated from any
touch tone telephone or online.
18
© 2001 Directed Electronics, Inc.
Glossary of Terms
Back-Up Battery Siren: Noise generating device responsible for
generating the "chirps" you hear, as well as the sound you hear
when the alarm is triggered.
Control Unit: The "brain" of your system. It houses the microprocessor which monitors and controls all of the system's functions.
Failsafe® Starter Kill: An automatic switch controlled by the security system which prevents the starter from cranking whenever the
system is armed. The starter is never prevented from cranking
when the system is disarmed, in Valet® mode, or should the starter
kill switch itself fail.
Input: A physical connection to the system. An input can be provided by a sensor, pinswitch or to existing systems on the vehicle,
such as the ignition.
LED: Red light mounted somewhere in the vehicle. It is used to
indicate the status of your system. It is also used to report triggers and faults in the system or sensors.
Shock Sensor: This system is packaged with a Doubleguard® Shock
Sensor. This sensor is on-board the control module and is designed
to detect impacts to the vehicle.
Transmitter: Hand-held, remote control which operates the
various functions of your system.
© 2001 Directed Electronics, Inc.
19
Trigger or Triggered Sequence: This is what happens when the
alarm "goes off" or "trips". The triggered response of your system
consists of 30 or 60 seconds of siren sounding and lights flashing.
Valet® Switch: A small push-button switch mounted on the
vehicle that is used to override the alarm when a transmitter is
lost or damaged, or to enter or exit Valet® mode.
Warn Away® Response: Lighter impacts will generate the Warn
Away response, which consists of several seconds of siren chirps
and light flashes.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular
zone. Two or more inputs often share the same zone.
20
© 2001 Directed Electronics, Inc.
✂
QUICK REFERENCE GUIDE:
To arm using your remote
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
■ You can activate, or arm, the system by pressing
on your transmitter
for one second. When the system arms, you will hear a short siren sound,
or chirp, and see the lights flash once.
To disarm using your remote
■ To disarm the system, press
. You will hear two chirps, and the parking lights will flash twice. If the siren chirps either four or five times when
disarming, see Diagnostics section. This is called Tamper Alert.
Disarming without a transmitter
■ Turn on the ignition. Press the Valet® switch the programmed number of
times within 15 seconds. The system should now disarm. If it does not,
you may have waited too long. Turn the ignition off and on and try again.
To disable the back-up battery siren
■ Locate the back-up battery siren. Remove the water protective cap on the
back side of the siren to expose the siren lock switch. Insert the siren key
into the siren lock switch and turn the key to the LEFT to disable the
back-up battery siren.
To enable the back-up battery siren
■ Turn the siren key back to the RIGHT. Replace the water protective cap on
the back side of the siren. WARNING! If the siren lock switch key is turned
to the enable position without the vehicle battery being connected, the
back-up battery siren will sound.
To enter or exit Valet® Mode
■ Turn ignition to "run" position, then turn to "off" position. Press and
release the Valet® switch within 10 seconds. The status LED will light solid
if you are entering Valet® Mode, and it will go out if you are exiting Valet® Mode.
To enter or exit Panic Mode
■ Press and hold
down for 1.5 seconds.
Important!
The unit and its components are water resistant, not waterproof; so the
warranty is void if the product has been damaged as a result of prolonged
water exposure or submersion.
Location of Valet switch__________________________________
✂
Number of Valet switch pulses for disarming_________________
© 2001 Directed Electronics, Inc.
21
The company behind this system is Directed Electronics, Inc.
Since its inception, DEI® has had one purpose, to provide consumers with the finest
vehicle security and car stereo products and accessories available. The recipient of
nearly 100 patents and Innovations Awards in the field of advanced electronic
technology, DEI is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 274-0200 for more information about our products and services.
DEI is committed to delivering world class quality products and services
that excite and delight our customers.
®
Vista, CA 92083
www.directed.com
© 2001 Directed Electronics, Inc. - All rights reserved
G122 3/01
Rev. B 1.0
Download PDF

advertising