Installation guide | Directed Electronics HVM702A Car Video System User Manual

OWNER’S GUIDE
INSTALLATION GUIDE
7” Widescreen
TFT LCD Color Monitor
Owner’s/Installation Manual
MODEL HVM 702A
© 2004 Directed Electronics, Inc. N81702A 12-04
NON-TRANSFERABLE LIMITED CONSUMER WARRANTY
Directed Electronics, Inc. (Directed) promises to the original purchaser that the
automotive video monitor and/or source unit(s) (the Product), excluding accessories, purchased and installed from a Directed authorized dealer within ninety (90)
days after purchase of the new vehicle, in which the Product is installed, will be
free from defects in materials or workmanship under normal use and conditions for
a period of three (3) years from date of purchase or the first 36,000 miles as registered on the new vehicle's odometer reading at time of delivery of the Product for
warranty service, whichever occurs first. Product purchased or installed more than
ninety (90) days after the new vehicle is purchased are warranted for a period of
one (1) year from date of purchase of the Product.
Directed promises to the original purchaser that all video accessories will be free
from defects in materials and workmanship under normal use and condition for a
period of ninety (90) days after the date of purchase. A sales receipt and/or warranty registration card is required to provide proof of date of purchase of the
Product or accessories.
Should the Product prove to be defective during the applicable warranty period, the
Product will be repaired or replaced with a new or comparable reconditioned
part(s), at Directed's election. To obtain warranty service, the Product must be
returned to a Directed authorized dealer along with proof of purchase and proof of
installation by an Authorized Directed Dealer.
This warranty is non-transferable and does not apply to any Product that has been
modified or used in a manner contrary to its intended purpose, and does not cover
damage to the Product caused by installation or removal of the Product. This warranty is VOID if the product has been damaged by accident or unreasonable use,
negligence, acts of God, neglect, improper service or other causes not arising out
of defect in materials or construction. This warranty does not cover the elimination
of externally generated static or noise, or the correction of antenna problems or
weak television reception, damage to tapes, video games, software, camcorders,
discs, speakers, accessories or vehicle electrical systems, cosmetic damage or damage due to negligence, misuse, abuse, failure to follow operating instructions, accidental spills or customer applied cleaners, damage due to environmental causes
such as floods, airborne fallout, chemicals, salt, hail, windstorms, lightning or
extreme temperatures, damage due to accidents, road hazards, fire, theft, loss or
vandalism, damage due to improper connection to equipment of another manufacturer, modification of existing equipment, use of a faulty tape cartridge or cleaning of the VCR head, or Product which has been opened or tampered with for any
reason or which has been damaged due to alteration or service performed by anyone other than Directed Electronics, Inc.
ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE,
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER
ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS LICENSED DEALERS
OR INSTALLERS. IN NO EVENT WILL DIRECTED ELECTRONICS, INC. BE LIABLE FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFITS),
BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL
DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.
Some states do not allow limitation on how long an implied warranty lasts. In such
states, the limitations or exclusions of this Limited Warranty may not apply. Some
states do not allow the exclusion or limitation of incidental or consequential damages. In such states, the exclusion or limitation of this Limited Warranty may not
apply to you. This Limited Warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
920-0002 Directed Video, 3 year Warranty Rev 11-04
2
Directed Video 3 year Automate RSE warranty 11-17-04.doc
© 2004 Directed Electronics, Inc.
Table of Contents
Non-Transferable Limited Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
What is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Power On/Off ........................................................................................8
Mute....................................................................................................8
Menu (Adjustments) ...............................................................................9
Headrest Housing/Bezel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Headrest Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Typical Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Multiple A/V Input Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting a monitor to multiple sources................................................14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
© 2004 Directed Electronics, Inc.
3
Important Notes
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
4
Before operating your LCD Monitor system, please read these instructions carefully.
Retain this manual for future reference.
Do not remove any WARNING stickers on the unit.
Do not use any chemical solvent, cleaning agent or corrosive detergent to clean
away dirt on the surface of the screen. Doing so may cause irreversible damage to the surface of the LCD screen. To clean off dirt or fingerprints, it is recommended that a soft-damp lens-cleaning cloth be used.
Using spare parts from another manufacturer may cause permanent damage to
the unit.
Avoid installing the monitor screen in a position that is exposed to direct sunlight and hot air vents.
Install the unit in a dry location, avoid condensation.
Ensure that all wiring is properly connected before operating the unit.
Should the LCD panel break, avoid contact with the broken glass or fluid leaking
out from the enclosure. If you come into contact, flush and clean the affected
areas with plenty of water. Seek medical attention immediately.
When operating the monitor, avoid touching or pressing on the LCD screen.
Excessive force will damage the LCD screen.
When installing this unit in a vehicle, ensure that the installation and use of
this unit is in compliance with local vehicle rules and regulations.
Before replacing a blown fuse, turn the unit off and disconnect all power. Ensure
the replacement fuse is of the same rating (5A) of the fuse being replaced.
If during operation the unit overheats or malfunctions, turn off the power and
contact your dealer. Do NOT disassemble the unit, there are no user serviceable parts in the unit.
Ensure that no foreign objects are in the unit when the LCD screen is closed.
The battery (CR2025) in the remote control has a useful lifetime of approximately 6-months. To ensure proper and reliable operation, replace the battery
in a timely manner.
When the unit is used in conjunction with a radio/TV tuner, reception quality
will vary depending on the geographic location and weather conditions.
The rated operating temperature range of the unit is 32º–92º F. Cool or warm
the vehicle to within this temperature range prior to unit operation.
The picture viewing quality of this LCD is dependent on the installed location.
Adjust the brightness control and/or the angle of the screen to achieve the
optimum visual quality.
© 2004 Directed Electronics, Inc.
Introduction
Congratulations on your purchase of the world’s finest video entertainment system.
At Directed we are committed to bringing you the most technologically advanced
products available. We are pleased that you chose a Automate Video product. Through
years of critical testing and hand craftsmanship, we have created a wide range of
video entertainment products for your viewing pleasure.
This system incorporates the use of on screen display menu controls that allows you
to configure the system to suit your own personal preferences. For your listening flexibility, audio can be heard by optional infrared (wireless) headphones.
To view other great products from Directed Electronics, please visit Automate at
www.automatecarsecurity.com.
Features
z High definition, low reflection TFT LCD screen – 1440 (W) X 234 (H)
z 16:9 wide screen ratio (full, 4:3, or wide selectable)
z All functions can be operated from the remote control (power, volume,
source select, etc.)
z Picture noise eliminated by implementation of Blue screen
z OSD (On Screen Display) of all functions
z Brightness, color, and tint controls provided
z Invert image control (Up/Down, Left/Right)
z One-touch dimmer control
z Low power consumption (750 mA at 12VDC)
z Input voltage tolerance (9VDC–16VDC)
z External A/V input
z 2-ch IR wireless transmitter
z Front headphone stereo output
z PAL/NTSC manual select
© 2004 Directed Electronics, Inc.
5
What is Included
„ 7” TFT LCD Color Monitor
„ Mounting hardware package
„ Headrest housing
„ EV sponge
„ Headrest bezel
„ DIN to RCA cable (for A/V input)
„ Remote Control Unit/battery
System Description
MONITOR
REMOTE CONTROL
19
8
18
17
9
10
16
11
12
1
2
3
4
5
6
15
14
13
7
MONITOR
1.
2.
3.
4.
5.
6.
7.
Headphone jack
Volume up/down buttons
Wireless headphone IR transmitter
Menu—changes the viewing aspect ratio (Full, 4:3, or Wide)
Power On/Off button
Remote control IR sensor receiver
DIN jack for external audio/video input
REMOTE CONTROL
8. Power On/Off button
9. SEL MUTE button—selects item on menu and serves as the mute On/Off button
6
© 2004 Directed Electronics, Inc.
10. Volume control—if the OSD is active, these allow scrolling through menu
options
11. Menu On/Off—press the menu button to go back to the previous selection
12. Scan—used in conjunction with a TV tuner
13. A/M—used in conjunction with a TV tuner
14. TX—not used
15. DIM—dims the LCD screen
16. Up/down button for menu
17. MODE—changes the viewing aspect ratio (Full, 4:3, or Wide)
18. SOURCE—used in conjunction with a TV tuner
19. Remote IR LED—IR LED used to transmit commands to the monitor
Remote Control
1. (S/T)—use these buttons to adjust the selected setting on the MENU screen.
2. SOURCE—press this button to select the video source (AV1/AV2).
3. MENU—press this button to display the MENU screen. Continue to press this
button additional times to scroll through the MENU selections.
4. POWER—press this button to turn power on or off to the unit.
© 2004 Directed Electronics, Inc.
7
Battery Replacement
1. Follow the instructions given in the illustration below to open the battery
holder.
2. Remove the old battery and replace it with a CR2025 or equivalent. The positive (+) side of the battery must be facing upward in the clip.
3. Push the battery holder into the body of the remote control until the battery
holder is locked.
4. Properly dispose of the old battery.
2
1
Operation
POWER ON/OFF
1. Press any button on the LCD screen, or press the POWER button on the remote
control to turn the monitor on.
2. To turn power off to the LCD screen press and hold the power button (PWR) on
the LCD screen for 2-seconds, or press the POWER button on the remote control.
NOTE: When using this monitor with a multiple A/V input selector (AV102); with
power on, momentarity press the power button on the LCD screen to select AV1 or AV2
signal source.
MUTE
Press the power on/off button on the monitor to mute the audio, press again to
restore the audio.
NOTE: The power on/off button on the monitor does not mute the audio when there
is an A/V input selector (VS102), in which case the button selects the A/V input.
8
© 2004 Directed Electronics, Inc.
Press the SEL button on the remote control to the mute the audio, press again to
restore audio.
NOTE: If the MENU button on the remote has been pressed prior to pressing the SEL
button, the SEL button now selects a menu item to be adjusted.
MENU (ADJUSTMENTS)
1. Press the MENU button on the remote to display the following four groups:
VIDEO
Bright
Color
Tint
Dimmer
Reset
AUDIO
Volume
Bass
Mute
H/P
MODE
Full
4:3
Wide
DISP
PAL/NT
UP/DN
LET/RIT
2. Use the S/T buttons on the remote to highlight the VIDEO, AUDIO, MODE, or
DISP groups.
3. Press the SEL button to select the desired group. Use the S/T buttons to
select the desired setting to change.
4. Use the W/X buttons to change the setting.
4. If no entry or action is taken within approximately 8-seconds the Menu will
disappear and any changes are saved. Pressing the MENU button will also exit
the adjustments screen.
VIDEO
BRIGHT(ness): 0–15
COLOR: 0–15
TINT: 0–15
DIMMER: ON–OFF (In the ON position the LCD screen is dimmed, which
offers better veiwing at night or in dimly lighted envirorments.)
RESET : YES–NO (This resets the unit back to the factory default settings
for the above adjustments.)
© 2004 Directed Electronics, Inc.
9
AUDIO
VOLUME: 0–15
BASS: ON OFF
MUTE: ON OFF
H/P: A-CH B-CH — This setting allows the use of 2 headphones on
different frequencies. If two video units are installed and; for example,
each unit is playing a different video, using two headphones set at the
same frequency may result in interference of the audio signal between the
two headphones. One of the video units should be set to A-CH and the
other to B-CH. A-CH is 2.3MHz left and 2.8MHz right, B-CH is 3.2MHz left
and 3.8MHz right. Ensure that the headphones being used are of different
receive frequencies, or are capable of 2-channel reception.
MODE
NOTE: In the Mode selection use the S/T buttons to select the desired setting and
press SEL to set the selected video mode.
FULL — A 4:3 picture is enlarged in the horizontal
direction only, enabling viewing of a 4:3
picture (standard picture) without any clipping of
the picture.
4:3 — Standard picture mode.
WIDE — A 4:3 picture is enlarged in the same proportion both vertically and horizontally. This setting
is ideal for cinema-sized pictures (wide-screen).
DISP
PAL/NT: PAL NT — video format (PAL or NTSC)
UP/DN: UP DN — picture is inverted
LET/RIT: LET RIT — picture is mirrored imaged (left-right swapped)
10
© 2004 Directed Electronics, Inc.
Headrest Housing/Bezel Installation
1. Remove the cover from the headrest.
2. Using the headrest housing as a template, position the housing over the backside of the headrest
and mark the foam with a felt tip pen. Cut the
marked portion of foam and pull out the cut portion.
3. Insert the headrest housing into the headrest
and secure the the headrest. Usually wire ties
attached to the headrest posts is sufficient.
NOTE: Ensure that the UP arrow on the headrest housing
is pointing up.
4. Replace the cover over the headrest. Mark 11/2” from the inside of the headrest housing and
cut the material away.
5. Optional Step: Glue the material to the inside of
the headrest housing. Take care not to use excessive glue so that the headrest bezel is not glued to
the headrest housing.
NOTE: Glue is not required if the material of the headrest
covering is of sufficient thickness to be tensioned by the
headrest bezel.
6. Insert the headrest bezel into the headrest
housing and secure the assembly using the provided hardware.
NOTE: Ensure that the UP arrow on the headrest bezel is
pointing up.
© 2004 Directed Electronics, Inc.
11
Headrest Installation
1. Unplug the DIN cable from the monitor.
8-pin main
DIN cable
5-pin adapter
cable
2. Connect the LCD screen’s 8-pin DIN plug into
the 8-pin DIN plug of the headrest.
NOTE: When assembling the cable, match the arrows at
each end of the connector.
NOTE: Feed and orient the connector assembly behind
the shroud mount in the lower right hand corner. You
may have to feed some of the DIN cable up into the
headrest to accomplish this positioning.
3. Position the monitor over the mounting shroud
and apply even pressure to each corner of the monitor until the internal clips lock the monitor in
place.
NOTE: Do not press on the LCD screen as this will damage the screen.
4. Tape the end of the DIN plug to prevent damage to the pins. Then feed this cable from the hollow post of the headrest down through the seat
back and connect it to the cable from the DVD player.
NOTE: Ensure the cable does not entangle or interfere
with the seat positioning/adjusting mechanism.
12
© 2004 Directed Electronics, Inc.
5. To remove the monitor from the mounting
shroud for service or repair, insert and slide a plastic card at the edge of the monitor. This will remove
the clip engagement of the monitor. Slightly lift
this side of the monitor out, then repeat this procedure on the other side of the monitor.
Typical Wiring Diagram
© 2004 Directed Electronics, Inc.
13
Multiple A/V Input Selector
Refer to diagram on the next page for the discussion that follows:
CONNECTING A MONITOR TO MULTIPLE SOURCES
When the monitor(s) power is turned on the input source will appear in the upper
right hand corner (AV1, AV2, etc.). Press the SOURCE button on the remote to
switch between the available sources for that monitor.
NOTE: If PARKING is displayed on the screen, it means that this monitor(s) will not
display video until the parking brake is set (vehicle parked).
NOTE: You cannot change sources on video output 3 using the source selector, Only
the remote will switch #3 output between the 3 video inputs.
For operating convienence, when the system is connected to several other devices
which have their own remotes, you can use those remotes through the HVM702a to
operate the other devices. This is done by connecting the Remote Eye IR interface
cable from the other devices to the R(emote) Sensor Input at the VS102 video
selector.
14
© 2004 Directed Electronics, Inc.
VS102
© 2004 Directed Electronics, Inc.
15
Troubleshooting
Use the following chart to assist in troubleshooting the system.
PROBLEM
SOLUTION
Power will not turn on
Check connections to the power
supply and other devices.
No picture or sound
Check connections of external
device.
Have picture, but no sound
Remote control does not work
Intermittent audio
Check if the volume is set to low. If
in A/V mode, check audio connections.
Avoid using the product under
strong & direct sunlight. Replace
the battery in the remote control.
Power supply voltage is too low.
TV picture appear to shakes while Bad reception. Check antenna and
driving
try reception in a better area.
No audio from headphone
16
Ensure the Power is switched on at
the headphone. Replace the
batteries in the headphone. Check
to ensure the frequency of the
headphone is the same as set up in
the monitor. Check the volume
level setting on the headphone.
© 2004 Directed Electronics, Inc.
Specifications
Power
12VDC (9–16VDC)
Power consumption
750mA Maximum @ 12VDC
Power consumption (stand-by) 50mA
Video type
PAL/NTSC
Video input level
1Vp-p, 75 ohm (composite)
A-ch 2.3 MHz/2.8MHz
IR frequency (left/right)
B-ch 3.2 MHz/3.8MHz
1m ±30º
IR range
1m ±15º
Headphone stereo output
0.5 watts - 16 ohms/channel
Actual screen size
155 (W) X 880 (H) mm
Dimensions
189.4 (W) X 126.5 (H) X 35 (D) mm
Weight
536 ±3 grams
Remote control battery
lithium battery CR2025, 3V
NOTE: Specifications are subject to change without notice.
© 2004 Directed Electronics, Inc.
17
18
© 2004 Directed Electronics, Inc.
Notes
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
© 2004 Directed Electronics, Inc.
19
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security, car stereo
products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of
advanced electronic technology, Directed is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed® is committed to delivering world-class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
www.directed.com
© 2004 Directed Electronics, Inc.—All rights reserved
N81702A 12-04
Download PDF

advertising