Programming instructions | Directed Electronics Model 690XV Automobile Alarm User Manual

Model 690XV
➤Owner’s Guide
limited lifetime consumer warranty
Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or
replace with a comparable reconditioned model any Directed unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated sensors and
accessories, which proves to be defective in workmanship or material under reasonable use
during the lifetime of the vehicle provided the following conditions are met: the unit was
professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY
© 2003 directed electronics, inc.
i
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤
➤
➤
➤
➤
➤
➤
➤
➤
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2003 directed electronics, inc.
table of contents
limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
remote control diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
standard remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
your warrantywarranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
remote control functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
standard button configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
standard icon configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
remote operation and programming instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
system signal paging features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
programmable remote control features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
passive arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
vehicle recovery system (vrs®) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
© 2003 directed electronics, inc.
1
remote control diagram
2
© 2003 directed electronics, inc.
standard remote configurations
1
Auxiliary Channel Out
2
Receive Indicator
3
Signal Indicator
4
Transmit Indicator
5
Lock Status Indicator
6
Unlock Status Indicator
7
Arming Status Indicator
8
Disarming Status Indicator
9
Door Switch Input Indicator
10
Warn Away® Response Indicator
11
Siren Status Indicator
12
Battery Level Indicator
13
Trigger ResponseIndicator
14
Hood Switch Input Indicator
15
Ignition Switch Input Indicator
16
Sensor Response Indicator
17
Sensor 1 Indicator - Full Trigger and Warn Away®
18
Sensor 2 Indicator - Full Trigger and Warn Away®
19
Trunk Switch Input Indicator
20
Vibrate Mode Indicator
21
Remote Start Indicator (n/a)
22
Disarm Button
23
Panic Button
24
Auxiliary Button
25
Arm Button
© 2003 directed electronics, inc.
3
what is included
➤
➤
➤
➤
➤
➤
➤
➤
➤
One control module
One Responder transceiver
Stinger® Doubleguard® dual-stage shock sensor
Revenger® Soft Chirp® six-tone programmable siren
Status LED indicator light
Push-button Valet button
Your warranty registration
Failsafe® Starter Kill ready circuitry
(may require additional labor)
FSK transceiver
important information
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. Due to the complexity of this system,
it must be installed by an authorized dealer only. Installation of
this product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with preprinted dealer certificates to verify that they are authorized.
This owner’s guide should help you to get the most out of your
system. Please take the time to read it prior to using the system.
4
© 2003 directed electronics, inc.
➜ system maintenance
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
The Battery Level indicator has four level indicators that serve as
a visual indication of battery charge. When the battery reaches a
low charge level that requires replacement, the remote control
will generate a single notification chirp, and the Battery Level
indicator will flash continuously.
FULL
REPLACE
EMPTY
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the
remote control observing the correct polarity. When power is
returned the remote control will light all icons in the LCD and
generate all beeper tones once.
➜ your warrantywarranty
Your warranty registration must be returned and the bar code
serial number must not be removed. If the warranty registration
is not returned, you do not have a warranty. It is also necessary
to keep your proof of purchase, which reflects that the product
was installed by an authorized dealer. Make sure that you receive
the warranty registration from your dealer.
© 2003 directed electronics, inc.
5
➜ fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
Directed Electronics, Inc.
436 Series
Tested to Comply
with FCC Standards
DRW-368
6
© 2003 directed electronics, inc.
remote control functions
The remote control buttons are used to send commands to the
system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for
the user’s specific needs by the installer.
➜ standard button configurations
Button
The System Arm and Multi-Level Security Arming functions are
controlled by pressing this button for one second.
Button
The System Disarm and High Security Disarm functions are
controlled by pressing this button for one second.
Button
Silent Mode™ and an optional auxiliary function are controlled
by this button. Silent Mode works by pressing this button for
less than one second before arming or disarming. An optional
auxiliary function, such as trunk release, can be controlled by
pressing this button for 1.5 seconds.
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
© 2003 directed electronics, inc.
7
and
Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
➜ standard icon configurations
Icon
The transmit icon will be displayed while the remote control is
transmitting a command to the vehicle.
Icon
The receive icon will be displayed while the remote control is
receiving a page from the vehicle.
Icon
The signal icon will be displayed if a command is transmitted to
the vehicle but a command page is not received.
Icon
The armed status icon will be displayed when the system is locked
and armed.
Icon
The disarmed status icon will be displayed when the system is
unlocked and disarmed.
Icon
The disarm icon will flash while the system is disarming
8
© 2003 directed electronics, inc.
Icon
The arm icon will flash while the system is arming.
Icon
The door icon will be displayed to indicate that a door is open
when arming the system (Bypass Notification) or opened when
the system is armed (Tamper Alert).
Icon
The warn icon will be displayed if the Warn Away® response has
been triggered while the system is armed.
Icon
The siren icon will be displayed as an indicator that the siren is
sounding.
Icon
The alarm icon will be displayed if the system has been violated,
and will continue to be displayed until the 60-second siren cycle
is complete.
Icon
The vibrate icon will be displayed when the Vibrate Mode is on.
Icon
The battery level icon is always displayed as an indicator of
Battery charge.
© 2003 directed electronics, inc.
9
Icon
The start icon is not used in this model.
Icon
The trunk icon will be displayed to indicate that the trunk is
open when arming the system (Bypass Notification) or opened
when the system is armed (Tamper Alert).
Icon
The Sensor 1 icon will be displayed if the Dual-Stage shock
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The Sensor 2 icon will be displayed if an additional Dual-Stage
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The hammer icon will flash when either Sensor 1 or 2 has been
triggered as either a Warn Away® response or triggered sequence.
Icon
The ignition icon will be displayed to indicate that the ignition
is on when arming the system (Bypass Notification) or turned on
when the system is armed (Tamper Alert).
Icon
The hood icon will be displayed to indicate that the hood is open
when arming the system or (Bypass Notification) opened when
the system is armed (Tamper Alert).
10
© 2003 directed electronics, inc.
Number Icons
When either of the channel 2 or 3 outputs is activated the appropriate icon will be displayed for five seconds.
remote operation and programming instructions
This security system operates at 434 MHz and incorporates
Directed’s proprietary XHF2 out-board Responder Technology
remote control. The high frequency combined with Binary Data
communication achieves superior range with two-way communication.
➜ system signal paging features
A page is the signal the control module sends to the remote
control as confirmation of receipt of a command or alarm system
status.
When the remote control receives a page it will generate a page
notification to the user (notifications are audible beeps or remote
vibration) and the LCD Icons will display the current system
status.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
© 2003 directed electronics, inc.
11
note: When the system is in Valet mode, the remote control will show the lock (5) and unlock (6) icons, but will
not generate a command page.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will
be sent to the remote control. After receipt of an Alarm Page, the
LCD icons will display the alarm system status information and
the remote control will generate Alarm Page alerts.
An Alarm Page alert is a single beep or vibration from the remote
control every 60 seconds to alert the user that the alarm system
was triggered and will continue until the alarm page is cleared.
note: If the transmiter is paged with an Alarm Page and
the WarnAway® is triggered before the Alarm Page is
recieved the transmitter will report the WarnAway® only
until the system is disarmed.
Page Recognition Mode
The remote control will leave a zone icon illuminated when it
has received a triggered response and will wait for you to recognize the violation. Press any button on the remote control, the
LCD information and Alarm Page alerts will be cleared.
note: The remote control buttons will not send a command to the system until the alarm page is cleared.
12
© 2003 directed electronics, inc.
➜ programmable remote control features
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming Mode has now been
entered.
Page Notification
The remote control can be programmed to notify the user of a
page by audibly beeping or remote vibration.
Beep Mode
Beep Mode includes alarm arm/disarm diagnostic beeps and
distinctive two-tone remote start beeps.
Vibrate Mode
Vibrate Mode makes page notification silent but does not include
diagnostic information or distinctive remote start notification.
Illumination
Illumination for the LCD display can be programmed on or off.
When programmed on the LCD will illuminate every time the
remote control receives a page or transmits a command.
Programming illumination on will decrease the life expectancy of
the battery.
Beep/Vibrate Mode
Within five seconds of entering Programming Mode, press
.
The remote control will beep once for on, twice for off. The
vibrate icon (13) will also turn on/off with each press.
© 2003 directed electronics, inc.
13
Illumination On/Off
Within five seconds of entering Programming Mode, press
. The remote will beep once for on, twice for off and the light
will turn on/off with each press.
Page Mode On/Off
After entering Programming Mode, press
within five
seconds to toggle on and off. When the Page Mode is on, the
remote control will wake up periodically to check for messages
from the security module. It will also wake up when any button
is pushed. When Page Mode is off, the remote control “sleeps”
until a button is pushed, extending the life of the battery.
Channel 1 Zone Select
After entering Programming Mode, press
within five
seconnds to toggle between hood, trunk, and hood and trunk.
The remote will bep once and show hood icon for hood, beep
twice and show trunk icon for trunk, and will beepthree time
and show both icons for hood and trunk. The default is the tunk.
To Exit Programming Mode
To exit Programming Mode, take no action for five seconds. The
remote control will generate two beeps to indicate programming
mode has been exited.
14
© 2003 directed electronics, inc.
using your system
The buttons used in the instructions in this manual correspond
to the standard configuration. Remember, this is not the only
way your transmitter may be set up. It can be custom configured
to meet your needs.
➜ active arming
You can activate, or arm, the system by pressing
on your
transmitter for one second. When the system arms, you will hear
a short siren sound, or chirp, and the parking lights will flash
once. If the vehicle’s power door locks have been connected to
the system, the doors will lock.
While the system is armed, the status LED will flash approximately once per second, indicating that the system is actively
protecting your vehicle. If you hear a second chirp after arming,
and see the status LED flashing in groups, refer to the Diagnostics
section of this guide. This extra chirp is called Bypass Notification.
➜ passive arming
The system also can be programmed to arm itself automatically
(called passive arming). If the system is programmed for passive
arming, it will automatically arm 30 seconds after the ignition is
turned off and the system "sees" you leave the vehicle by opening
and closing a door. Whenever the system is in its 30-second
passive-arming countdown, the status LED will flash twice as
© 2003 directed electronics, inc.
15
fast as it does when the system is armed. The siren will chirp
once 20 seconds after the last door has been closed. The system
is not actually armed at that point. The system arms and the
doors lock (if connected and programmed for passive locking) at
the 30 second mark, but the siren will not chirp. The early chirp
provides you with a 10-second warning prior to arming.
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm (unless forced passive arming is programmed on). See Programming Options section of this
guide. Additionally, each time a protected entry is triggered during the arming countdown, the 30-second
countdown starts over.
When armed, your vehicle is protected as follows:
➤
Light impacts will trigger the Warn Away® signal. When
triggered, the siren will chirp and the parking lights will flash
for a few seconds.
➤
Heavy impacts will trigger the system. The triggered
sequence is between 1-180 seconds of constant siren and
flashing parking lights.
➤
If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the system with your transmitter if you inadvertently open the door
while the system is armed, while still providing an instant
response (even if the door is immediately closed).
16
© 2003 directed electronics, inc.
➤
Turning on the ignition key will trip the same two-stage
response as opening a door.
➤
The optional starter kill prevents the vehicle’s starter from
cranking.
➜ multi-level security arming
Multi-Level Security Arming allows you to select which of the
security system's inputs or sensors will be active and which will
be bypassed at the time that the system is armed. (See the Table
of Zones section of this guide.) Pressing
again within five
seconds of arming the security system will activate the MultiLevel Security Arming feature. Each time
is pressed again, a
different security level is selected. The different security levels
can be selected as follows:
➤
Press
one time: The siren chirps once. The system is
armed.
➤
Press
a second time within five seconds: The siren
chirps twice followed by a long chirp. Zone 2 is now
bypassed.
➤
Press
a third time within five seconds: The siren chirps
three times followed by a long chirp. Zone 4 is now
bypassed.
➤
Press
a fourth time within five seconds: The siren chirps
four times followed by a long chirp. Zones 2 and 4 are now
bypassed.
➤
Press
a fifth time within five seconds: The siren chirps
five times followed by a long chirp. All input zones, except
© 2003 directed electronics, inc.
17
the ignition, are now bypassed.
➤
Continued pressing of
will begin the Multi-Level
Security Arming cycle over again.
note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then
re-armed, all the zones will be active again.
➜ arming while driving
Your system can be armed while driving the vehicle. Simply press
on your transmitter for two seconds while the vehicle is
running or while the ignition is on. The siren will chirp once and
then once more to indicate that the ignition is on. The security
system will not respond to any input except the door triggers and
the Failsafe® Starter Kill (if installed) will not be activated. The
security system will disarm automatically whenever the ignition
is turned off. The siren will chirp twice and the LED will stop
flashing.
note: If programmed for the optional Vehicle Recovery
System (VRS®) feature, arming with the transmitter will
arm the VRS® feature. (See Vehicle Recovery System®
section of this guide.)
18
© 2003 directed electronics, inc.
➜ disarming
To disarm the system, press
. You will hear two chirps, and
the parking lights will flash twice. If the power locks are
connected to the system, the doors will unlock. If the siren chirps
either four or five times when disarming, refer to the Diagnostics
section of this guide. This is called Tamper Alert.
➜ high security disarm
This security system offers High Security Disarm. High Security
Disarm is a feature that makes it possible to silence and reset the
system while it is triggering, without disarming the system. If the
system is triggered and the siren has been sounding for longer
than six seconds, pressing
or
on the remote transmitter
will stop the trigger and return the unit to the armed state. The
system will not disarm, but rather reset. This prevents you from
disabling the system should you wish to disarm it without visually checking the vehicle. Pressing
after resetting the system
will disarm the system; pressing this button during the first six
seconds of the triggered sequence will disarm the security system
immediately. The six second timer is provided for your convenience, in case the system is accidentally triggered.
© 2003 directed electronics, inc.
19
➜ disarming without a transmitter
This feature allows you to disarm the security system without the
remote transmitter should it be lost, damaged, or disabled. In order
to disarm the system without a remote transmitter, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position. Press the Valet button the
preset number of times (one to
DRW-35
five times) within 15 seconds.
After five seconds the system will
disarm. If the system does not
disarm, you may have waited too
long; turn the ignition off and on and try again.
Location of Valet Button_________________________________
Number of Pulses______________________________________
important! The unit can be programmed to respond to
one to five pulses of the Valet button for the disarm function. Be sure to check with the installer for the desired
programming.
20
© 2003 directed electronics, inc.
➜ silent mode
To temporarily turn off the arm or disarm chirps, use Silent
Mode™. Simply press
for less than one second before
arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only. If you want the arm/disarm
chirps turned off permanently, your dealer can do this for you.
note: The Warn Away® response to lighter impacts is
bypassed if the system is armed using Silent Mode. This
ensures that no chirps will be emitted by the siren in an
area you want chirp-free. The system is still fully capable
of triggering. Only the Warn Away® response is
bypassed.
➜ panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your transmitter. Just
press
for two seconds, and you will enter Panic Mode. The
siren will sound and the parking lights will flash for the
programmed siren duration. To stop Panic Mode at any time,
press
on the remote transmitter again.
© 2003 directed electronics, inc.
21
➜ valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the remote transmitter,
but all convenience functions (door locks, trunk release, etc.)
will continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
DRW-35
switch within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
To enter or exit Valet Mode using the transmitter:
1. Open any vehicle door.
2. Press
.
3. Press
.
4. Press
again.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
22
© 2003 directed electronics, inc.
➜ nuisance prevention® circuitry
Your system has Directed’s Nuisance Prevention® Circuitry
(NPC®). It prevents annoying repetitive trigger sequences due to
faulty door pin switches or environmental conditions such as
thunder, jackhammers, airport noise, etc.
Example
If the alarm triggers three times within a 60-minute period and
each time the same sensor or switch triggers the alarm, NPC® will
interpret those triggers as false alarms. After the third trigger,
NPC® ignores, or bypasses, that sensor or switch (along with any
other sensors or switches sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the system while it is being
bypassed, the 60-minute bypass period will start over. This
ensures that a sensor that continually triggers will remain
bypassed.
Doors are covered by NPC® differently; if the alarm is triggered
by an open door for three full cycles, the doors will be bypassed
until the trigger ceases.
note: Arming and disarming the system does not reset this
function.The only ways to reset a bypassed zone are for it
to not trigger for 60 minutes, or to turn on the ignition. If
testing your system, it is important to remember that the
NPC® programming can cause zones to be bypassed and
appear to stop working. If five chirps are heard when disarming, NPC® has been engaged. If you wish to clear the
NPC® memory, turn the ignition key on.
NPC® is programmable. See Programming Options section of this
guide.
© 2003 directed electronics, inc.
23
diagnostics
The microprocessor at the heart of your security system is
constantly monitoring all of the switches and sensors that are
connected to it. It detects any faulty switches and sensors and
prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred
during your absence. Refer to the System Status Chirps and Table
of Zones charts for diagnostic information.
➜ arming diagnostics
If the system is armed while an input is active (door open, sensor
triggering, etc.) the unit will chirp once when arming and then
one more time a few seconds later. This is called Bypass
Notification.
note: Bypass Notification will not occur when using
Silent Mode™ or if chirps have been programmed OFF.
The security system will ignore the input that was active when
the system was armed, until the input goes away. Three seconds
later the system will monitor that input normally. For example,
if your vehicle has interior light exit delay, and you arm the
system before the interior light goes out, you may hear Bypass
Notification chirps. Once the light shuts off, however, the doors
are monitored normally.
24
© 2003 directed electronics, inc.
➜ disarming diagnostics
Extra disarm chirps are the Tamper Alert. If four chirps are heard
when disarming, the system was triggered in your absence. If five
chirps are heard, a zone was triggered so many times that Nuisance
Prevention® Circuitry has bypassed that zone. The status LED will
indicate which zone was involved. (See Table of Zones section of this
guide.) The system will retain this information in its memory, and
continue to chirp four or five times each time it is disarmed, until
the next time the ignition key is turned on.
➜ system status chirps
The siren will chirp when arming/disarming the system. The
pattern of chirps will audibly report the system’s status as
described below.
Action
Number of Chirps
Description
Arm
1
System armed
Arm
1 (3-second delay), 1
System armed with
Bypass Notification
Disarm
2
System disarmed
Disarm
4
System disarmed with
Tamper Alert
Disarm
5
System disarmed NPC
active
© 2003 directed electronics, inc.
25
➜ table of zones
The zone number is the number of LED flashes used by the
system to identify that input. The standard input assignments
are listed below, along with spaces to write in any optional
sensors or switches you have had installed.
Zone - Number
of LED Flashes
Dealer-Installed
Options
Description
1
Instant trigger - often used
for hood/trunk pinswitches
2
Instant trigger - a heavier impact
detected by the shock sensor
3
Door switch trigger
4
Instant trigger - for optional sensors
5
Ignition trigger
➜ interpreting zone diagnostics
Warn Away responses are not reported by arming or disarming
diagnostics. If you receive a Bypass notification when arming or
a Tamper Alert notification when disarming, look at the LED.
Active or triggered zones will be indicated by a pattern of blinks
by the LED.
Example
If Zone 3 was active or triggered, the LED will blink three times
with a two-second pause. Then it will blink three times again,
and repeat until the ignition is turned on.
26
© 2003 directed electronics, inc.
note: Your system stores the last two triggered zones in
memory. If your system has been triggered but the LED
has been reset by turning on the ignition, your dealer can
still recall the last two zones that were triggered. Contact
your dealer for details.
code hopping
The receiver and transmitters each use mathematical formulas
called algorithms to change their codes each time the transmitter
is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes
should be. This helps to keep the transmitter "in sync" with the
control unit even if you use the remote control out of range of
the vehicle. However, if the transmitter has been pressed many
times out of range of the vehicle, or if the battery has been
removed, it may get out of sync with the control unit and fail to
operate the system. To re-sync the remote control simply press
of the transmitter several times within range of the vehicle.
The alarm will automatically re-sync and respond to the transmitters normally.
© 2003 directed electronics, inc.
27
high frequency
Your system transmits and receives at 434 MHz. This provides a
cleaner spectrum with less interference and a more stable signal.
Enjoy a phenomenal increase in range – even in areas with high
radio interference.
owner recognition
Owner Recognition is a feature available exclusively from Directed.
Using the Directed Bitwriter, a hand-held programming tool, your
dealer can program many of the system settings. The programmer
makes it possible to program different settings for each transmitter
that is used with the system. Then, whenever a specific transmitter
is used, the system will recall the settings assigned to that transmitter. Owner Recognition lets up to four users of the system have
different settings that meet their specific needs. It is almost like
having four separate alarms in your vehicle, one for each user.
note: Owner Recognition cannot be programmed without a Directed Bitwriter and the necessary software.
Check with your dealer for more information.
28
© 2003 directed electronics, inc.
rapid resume logic
This Directed system will store its current state to non-volatile
memory. If power is lost and then reconnected, the system will
recall the stored state from memory. This means if the unit is in
Valet Mode and the battery is disconnected for any reason, such
as servicing the car, when the battery is reconnected the unit will
still be in Valet Mode. This applies to all states of the system
including arm, disarm, VRS®, and Valet Mode.
power saver mode
Your system will automatically enter Power Saver Mode while
armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw to the
vehicle’s battery. Power Saver Mode takes over under the
following conditions:
➤
Power Saver when the system is armed: After the system has
been armed for 24 hours, the LED will flash at half its
normal rate, decreasing the system's current draw.
➤
Power Saver in Valet Mode: When the system enters Valet
Mode the LED illuminates steadily. If the vehicle is not used
(ignition is not turned on) for a period of one hour while the
system is in Valet Mode, the LED will shut off. If the system
remains in Valet Mode, the LED will come back on the next
time the ignition is turned on and then back off.
© 2003 directed electronics, inc.
29
programming options
Programming options control what your system does during
normal operation, and require few or no additional parts.
However, some may require additional installation labor.
The following is a list of the program settings, with the factory
settings in Bold:
➤
➤
➤
➤
Active arming (only with the transmitter) or passive arming
(automatic arming 30-seconds after the last door has been
closed).
Arming/disarming confirmation siren chirps on or off.
The ignition controlled door lock feature on or off: With
this feature on, the doors will lock three seconds after the
ignition is turned on, and unlock when the ignition is
turned off. The system will not lock the doors when the ignition is turned on with any door open. If your installer is
programming the security system with the Directed
Bitwriter, ignition lock and unlock are independent features
and can be programmed separately.
Passive door locking (with passive arming) or active door
locking (only when arming with the transmitter). Passive
locking allows the vehicle's doors to lock when the security
system passively arms (after the 30 second countdown). This
feature only works if passive arming has been programmed.
note: When programmed for passive arming and active
lock, if the system is disarmed without a door being
opened, the system will relock the doors when it passively rearms.
30
© 2003 directed electronics, inc.
➤
Panic mode enabled/disabled with the ignition on: Some
states have laws against siren capability in a moving vehicle.
➤
Forced passive arming on or off: If your system is
programmed for passive arming and the forced passive
arming feature has been programmed on, the system will
passively arm after one hour, even if a protected entry has
been left open. This feature is useful if a door has been left
ajar when leaving the vehicle. Forced passive arming ensures
that the security system will be armed in every situation.
note: When the system passively arms after one hour, the
entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger
the system. However, the remaining inputs to the system
are fully operational.
➤
Automatic Engine Disable (AED) on or off: The purpose of
this feature is to protect the vehicle from being stolen at all
times, regardless of whether or not the alarm is armed. If
AED is programmed on, the starter of the vehicle will be disabled 30 seconds after the ignition is turned off. Once the
key is turned off, the LED will flash slowly (one-half its
normal armed rate) to indicate the AED arming cycle.
Thirty seconds later, the starter of the vehicle will be disabled. To start the car, it will be necessary to disarm the
system with the transmitter. It is also possible to disarm the
AED feature by turning the ignition key to the RUN position and pressing the Valet button the programmed number
of times. AED is disabled when the system is in Valet Mode.
© 2003 directed electronics, inc.
31
note: This feature will only function if the Failsafe®
Starter Kill relay has been installed.
➤
Full trigger response 30 or 60 seconds: This determines how
long the full triggered sequence lasts. Some states have laws
regulating how long a security system can sound before it is
considered a nuisance. If your installer is programming the
security system with the Directed Bitwriter, the full triggered
response can be programmed for any duration ranging from
1 to 180 seconds.
➤
Nuisance Prevention® Circuitry on or off: Please refer to the
NPC® section of this manual for a complete explanation of
how NPC® operates. If NPC® is programmed off, the security system will respond to inputs from any sensor indefinitely.
note: Because many states have laws regulating security
systems, programming NPC® off may cause your system
to violate state laws.
➤
Progressive door trigger on or off: When the system is armed
and a door is opened, the system responds with ten chirps
prior to beginning the full triggered sequence. If an instant
trigger is desired, the progressive door trigger can be programmed off.
➤
Valet pulse count: The number of presses of the Valet button
required to disarm the security system, AED, or the VRS®
system can be programmed from one to five presses. The
default setting is one press.
32
© 2003 directed electronics, inc.
➤
Siren tones and chirp volume: The output of the Revenger®
Soft Chirp® siren consists of six different tones in sequence.
Any of these tones can be eliminated by your dealer, resulting in a unique, easily identifiable siren sound. The siren
chirps can be either full volume or six decibels quieter than
the full alarm blast.
installation options
The system has many options that may require extra parts and
labor. Some of the possibilities are listed here.
➤
Progressive unlocking: In most cars with electric power door
locks, the system can be configured so that when the system is
disarmed, only the driver’s door unlocks. A second press of the
button unlocks the other doors.
➤
Vehicle Recovery System (VRS®): VRS® is an anti-carjacking
device designed to help in the safe recovery of your vehicle
in case of a carjacking. Please refer to the Vehicle Recovery
System section of this guide for a complete explanation of
how the Vehicle Recovery System operates.
© 2003 directed electronics, inc.
33
vehicle recovery system (vrs®)
The optional VRS® feature is designed to ensure that any unauthorized user of your vehicle (even if using your keys and remote
control) will not be able to permanently separate you from your
vehicle.
The VRS® cannot prevent a carjacking attempt; however, it does
ensure that if your vehicle is taken by an unauthorized user, it will
be disabled (after several progressive warnings) as safely as
possible. Should a carjacking occur, the VRS® allows you to
concern yourself with your personal safety without worrying
about your property.
Directed has engineered this vehicle security system, the Failsafe®
Starter Kill, and the VRS® feature to provide the best combination of personal safety and property protection available. When
properly installed, the system can never inadvertently stop your
vehicle in traffic or on railroad tracks while the vehicle is in operation. It is unlike other systems that shut down your engine
while it is running. This system is designed to perform starter interrupt, or starter kill. The Failsafe® Starter Kill cannot shut
down an already-running engine – it can only prevent an engine
from starting in the first place.
important! Any installation that allows this product to
shut down a vehicle's engine when it is running is contrary to the product’s design and intended usage, and
Directed hereby expressly disclaims any liability resulting
therefrom.
34
© 2003 directed electronics, inc.
➜ arming the vrs
®
To arm the VRS®, turn the ignition to the ON position and press
the arm button on the remote transmitter for one second. The
parking lights will flash and the siren will chirp once. This can be
done before driving or while driving the vehicle. Once the system
is armed, it will initiate its triggered sequence (see below) if any
door is opened and closed. If you are forced from the vehicle, the
system will trigger as the door is opened and closed. This is how
the system works to combat intersection carjacking. To protect
against parking lot carjacking, arm the VRS® before leaving the
vehicle. The system will now trigger automatically the next time
you or anyone drives the vehicle. This helps to protect the vehicle
if someone takes your keys and remote transmitter by force in a
parking lot.
note: If the VRS® system is armed while operating the vehicle and not disarmed prior to leaving the vehicle, it is still
armed and will trigger the next time the vehicle is driven.
➜ vrs triggered sequence
®
Fifteen seconds after the last door has closed, the system’s status
LED will begin flashing. This delay is intended to allow you time to
distance yourself from your vehicle in the event of a carjacking.
Forty-five seconds later, the siren begins chirping and the park-
ing lights begin flashing. This time could be used to notify authorities that your vehicle has been hijacked, and tell them what
the VRS® will do next.
© 2003 directed electronics, inc.
35
Fifteen seconds after the siren chirps begin, the siren’s output will
change to a continuous blast.
From this point on, when the ignition key is turned off, the VRS®
will immediately turn on the starter kill. This will prevent the
vehicle from being restarted, thus immobilizing it at that spot.
Three minutes after the constant siren output begins, the flashing
parking lights and the siren will stop. The starter kill will remain
active until the system is disarmed. If the door is opened or the
ignition is turned off and on in an attempt to restart the car, the
siren and light flashing will begin again.
➜ disarming the vrs
®
Take the time to familiarize yourself with the VRS® triggering sequence and the disarm procedure. It is important to recognize
and identify the VRS® trigger sequence and know how to disarm
it in case of accidental activation.
Once the VRS® is armed, it does not disarm automatically. You
must disarm it the next time you operate the vehicle. You must
disarm it with one of the following procedures:
If the system has not entered the triggered sequence (siren has
not started chirping):
1. Turn the ignition on.
2. Press
on the transmitter for one second.
The lights will flash and the siren will chirp
twice.
36
© 2003 directed electronics, inc.
If the system has entered the triggered sequence (siren has begun
chirping), pressing the disarm button of the transmitter will not
disarm VRS®. To disarm the VRS® during a VRS® trigger
sequence:
1. Turn the ignition on.
2. Press the Valet switch the preprogrammed number of times to
DRW-35
disarm the VRS system.
note: If the VRS® system has begun its chirping
sequence, the ignition must be turned off, then on to disarm. If you are driving the vehicle at the time, pull to a
safe place away from traffic and follow the triggered
sequence disarm procedure.
glossary of terms
Control Unit: The "brain" of your system. Usually hidden under
the dash area of the vehicle. It houses the microprocessor which
monitors your vehicle and controls all of the system's
functions.
Fail Safe Starter Kill: An automatic switch controlled by the secu-
rity system which prevents the vehicle’s starter from cranking
whenever the system is armed. The vehicle is never prevented
from cranking when the system is disarmed, in Valet mode, or
should the starter interrupt switch itself fail. Your system is ready
for this feature, however installation may require additional
labor.
© 2003 directed electronics, inc.
37
Input: A physical connection to the system. An input can be
provided by a sensor, pinswitch or through an existing system in
the vehicle, such as ignition or courtesy lights.
LED: Blue light mounted somewhere in the vehicle. It is used to
indicate the status of your system. It is also used to report triggers and faults in the system or sensors.
Shock Sensor: This is a sensor mounted in the vehicle that is
designed to pick up impacts to the vehicle or glass.
Siren: Noise generating device usually installed in the engine
compartment of the vehicle. It is responsible for generating the
"chirps" you hear, as well as the six tones you hear while the
alarm is triggered.
Transmitter: Hand-held, remote control which operates the
various functions of your system.
Trigger or Triggered Sequence: This is what happens when the
alarm "goes off" or "trips". The triggered response of your
system consists of the siren sounding and parking light flashing
for the programmed duration.
Valet Switch: A small push-button switch mounted somewhere
inside the vehicle. It is used to override the alarm when a transmitter is lost or damaged, or to enter or exit Valet mode.
Warn Away Response: Lighter impacts to the vehicle will generate
the Warning Zone response. It consists of several seconds of siren
chirps and parking light flashes.
38
© 2003 directed electronics, inc.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular
zone. Two or more inputs often share the same zone.
security & convenience expansions
Here we have listed only some of the many expansion options
available. Please contact your dealer for a complete explanation
of all the options available to you.
Audio Sensor: Metal on glass, glass cracking, and breaking glass
each produce distinctive acoustic signatures. The 506T audio
sensor uses a microphone to pick up sounds, and then analyzes
them with proprietary acoustic software to determine if the glass
has been struck.
Backup Battery: The 520T keeps the system armed, triggers the
alarm and keeps the starter kill active if main battery power is
disconnected.
Field Disturbance Sensor: An invisible dome of coverage is estab-
lished by installing the 508D "radar" sensor. Your security
system can then react to any intrusions into this field with the
triggered sequence.
Headlight and Parking Light Automation: The 545T Nite-Lite®
will automatically turn on your parking and headlights when it
gets dark. In addition, the 545T will turn your headlights on
© 2003 directed electronics, inc.
39
whenever the windshield wipers are used. A transmitter function
can also be used to turn on your parking and headlights for a
programmed time.
Power Trunk Release: The channel two output of the system can
operate a factory power release for the vehicle’s trunk or hatch.
(An additional relay may be required.) If the factory release is not
power activated, then Directed's 522T trunk release solenoid can
often be added.
Power Window Control: Automatic power window control is pro-
vided with the 529T and 530T systems.
Mobile Video: This system is compatible with Directed Video’s
MCB1000 Multi-Channel Controller, featuring on-screen security system programming and zone trigger information.
Valet® Start System: For the ultimate in convenience, the Valet®
start system can start your vehicle, monitor engine functions,
and power your climate control system with a push of a button.
Over-rev protection, open-hood lockout, brake pedal shutoff,
and automatic timer shutoff are all included. (This feature is
only for automatic transmission, fuel-injected gasoline vehicles.)
543T XHFplus External Receiver/Antenna: The 543T XHFplus
external receiver/antenna can be used to upgrade the transmitter/receiver performance in areas of high radio interference
such as military bases, airports, and hospitals.
40
© 2003 directed electronics, inc.
✂
QUICK REFERENCE GUIDE
To arm using your remote
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
➤
You can activate, or arm, the system by pressing
on your transmitter for one
second. When the system arms, you will hear a short siren sound, or chirp, and
the parking lights will flash once. If the vehicle’s power door locks have been
connected to the system, the doors will lock.
To disarm using your remote
➤
To disarm the system, press
. You will hear two chirps, and the parking
lights will flash twice. If power locks are connected to the system, the doors will
unlock. If the siren chirps either four or five times when disarming, see
Diagnostics section. This is called Tamper Alert.
Arming while driving
➤
Press
on your transmitter for two second while the vehicle is running. The
system will chirp once and then once more to indicate that the ignition is on.
Disarming without a transmitter
➤
Turn on the ignition. Press the Valet button the programmed number of times
within 15 seconds. After five seconds, the system will disarm. If it does not, you
may have waited too long. Turn the ignition off and on and try again.
To enter or exit Valet Mode
➤
Turn ignition to RUN position, then turn to OFF position. Press and release
the Valet button within 10 seconds. The status LED will light solid if you are
entering Valet Mode, and it will go out if you are exiting Valet Mode.
To activate Panic Mode
➤
Press and hold
down for one second.
To exit Panic Mode
➤
Press
on the transmitter.
To activate Silent Mode™
➤
Press
briefly before arming or disarming, and the confirmation chirp(s)
will be eliminated for that one operation only.
Location of Valet Button_______________________________
✂
Number of Valet Button pulses for disarming_____________
© 2003 directed electronics, inc.
41
42
© 2003 directed electronics, inc.
© 2003 directed electronics, inc.
43
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed has had one purpose, to provide consumers with the
finest vehicle security and car stereo products and accessories available. The recipient
of more than 20 patents in the field of advanced electronic technology, Directed is
ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed® is committed to delivering world class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
www.directed.com
© 2003 Directed Electronics, Inc. - All rights reserved
G434V 7-03
Download PDF

advertising