Directed Electronics XA-3002 Stereo Amplifier User Manual


Add to my manuals
20 Pages

advertisement

Directed Electronics XA-3002 Stereo Amplifier User Manual | Manualzz

XA-3002

XA-6002

XA-6004

XA-5001

XA-8001

2

CONGRATULATIONS

Congratulations for choosing an Xtreme

Series power amplifier, by Directed

Audio. This high performance product has been designed and engineered by

Directed Electronics, the industry leader in high quality automotive security and audio equipment since 1990. With the

Xtreme Series power amplifiers,

Directed Audio continues to set new standards of performance, reliability, and affordability in the mobile electronics industry.

Featuring high-efficiency MOSFET power supplies and flexible built-in crossovers housed in a rugged, extruded aluminum extrusion with carbon fiber style trim panels, Xtreme power amplifiers will excite and delight car audio enthusiasts with years of high performance audio reproduction.

Xtreme Series amplifiers come with a two-year limited warranty if sold and installed by an authorized Directed dealer. If not installed by an authorized dealer, Xtreme Series amplifiers are covered by a one-year, parts-and-labor limited warranty. Be sure to retain your original purchase receipt, and refer to the warranty section of this guide for full details about your coverage.

TABLE OF CONTENTS

Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Limited Two-Year Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . .3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Front Panel Connections/Controls . . . . . . . . . . . . . . . . . . . . . . . . . . .6

REAR Panel Connections—XA-3002/XA-6002 . . . . . . . . . . . . . . . . . .11

High Level Harnesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Crossover Settings and Gain Adjustment . . . . . . . . . . . . . . . . . . . . . . .17

CEA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

© 2006 Directed Electronics—all rights reserved

LIMITED TWO-YEAR CONSUMER WARRANTY

Directed Electronics (Directed) promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product

PROVIDED the product was installed by an authorized Directed dealer. During this twoyear period, there will be no charge for this replacement

PROVIDED the unit is returned to Directed, shipping pre-paid. If the unit is installed by anyone other than an authorized Directed dealer, the warranty period will be 1 year from the date of purchase by the dealer as indicated by the date code marking of the product. During this 1-year period there will be no charge for this replacement

PROVIDED the unit is returned to Directed, shipping pre-paid. This warranty is non-transferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose, and does not cover damage to the unit caused by installation or removal of the unit.

This warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper service or other causes not arising out of defects in materials or construction.

ALL WARRANTIES INCLUDING

BUT NOT LIMITED TO EXPRESS

WARRANTY, IMPLIED WARRANTY,

WARRANTY OF MERCHANTABILITY,

FITNESS FOR PARTICULAR PURPOSE, AND

WARRANTY OF NON-INFRINGEMENT OF

INTELLECTUAL PROPERTY ARE EXPRESSLY

EXCLUDED TO THE MAXIMUM EXTENT

ALLOWED BY LAW, AND DIRECTED

NEITHER ASSUMES NOR AUTHORIZES

ANY PERSON TO ASSUME FOR IT ANY

LIABILITY IN CONNECTION WITH THE

SALE OF THE PRODUCT. DIRECTED HAS

ABSOLUTELY NO LIABILITY FOR ANY AND

ALL ACTS OF THIRD PARTIES INCLUDING

ITS AUTHORIZED DEALERS OR

INSTALLERS. Unit must be returned to

Directed, postage pre-paid, with: consumer’s name, telephone number, and address, authorized dealer’s name and address, and product description.

IN ORDER FOR THIS

WARRANTY TO BE VALID, YOUR UNIT

MUST BE SHIPPED WITH PROOF OF

INSTALLATION BY AN AUTHORIZED

DIRECTED DEALER. ALL UNITS RECEIVED

BY DIRECTED FOR WARRANTY REPAIR

WITHOUT PROOF OF DIRECTED DEALER

INSTALLATION WILL BE COVERED BY THE

LIMITED 1-YEAR PARTS AND LABOR

WARRANTY. Note: This warranty does not cover labor costs for the removal and reinstallation of the unit.

BY PURCHASING THIS

PRODUCT, THE CONSUMER AGREES AND

CONSENTS THAT ALL DISPUTES BETWEEN

THE CONSUMER AND Directed SHALL BE

RESOLVED IN ACCORDANCE WITH CALI-

FORNIA LAWS IN SAN DIEGO COUNTY,

CALIFORNIA.

© 2006 Directed Electronics—all rights reserved

3

4

FEATURES

„

„

„

„

High-speed MOSFET power supplies

Complimentary bipolar transistor outputs

Either mono only (XA-8001, XA-

5001) or stereo/mono (XA6002).

The XA-6004 can have rear bridged and front stereo or variations thereof.

2 ohm stereo stable/4 ohm mono stable

„

„

„

„

„

„

„

Built-in 2-way variable crossovers

+6 or +12 dB switchable bass boost (+8dB on XA-6004)

Adjustable input gain

Power/status LEDs

Thermal, short-circuit, over-current, and reverse polarity protection

Chrome-plated RCA inputs

Heavy duty screw terminals

WARNING

High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result.

INSTALLATION GUIDELINES

They may also impair a driver’s ability to hear traffic sounds or emergency vehicles. Use common sense and practice safe listening habits when listening to or adjusting your audio system.

1. Please read this owner’s manual carefully before installing this amplifier.

2. Disconnect the battery ground terminal prior to making any electrical connections.

3. Check for any hazards or obstructions such as gas tanks, fuel or brake lines, and wiring harnesses before mounting the amplifier.

4. Pick a mounting location that will provide adequate access and ventilation and protect the amplifier from heat, moisture, and dirt.

5. Avoid sharp metal areas when routing cables to the amplifier, and run RCA cables away from the power cables and other potentially noisy car harnesses.

© 2006 Directed Electronics—all rights reserved

6. The amplifier should be grounded with a short, heavy gauge wire connected directly to the car at a bare metal surface, preferably scraped body sheet metal. Do not use factory ground locations, seat bolts, or brackets that are spotwelded.

7. Always fuse your power connection within 8 to 10 inches of the battery terminal. Use a fuse or circuit breaker rated slightly more than the on-board fuse(s) of the amplifier(s). The gauge of power wire used should take into account the total current draw of the system, and the length of wire used. IASCA and other auto sound competition organizations have charts available for this; you can also find a chart in the MECP study guide. Minimum wire gauge recommendations for the individual amplifiers are listed on the specification page. Always use the same gauge wire for the amplifier ground that you use for the power wire. Be sure to examine the battery ground cable of the vehicle, and if necessary, upgrade it by adding an additional ground wire that is the same gauge as the amplifier power wire.

Remember, the amplifier can only deliver its rated output when it is not current limited by the power and ground supply wires.

8. This amplifier is designed to drive a speaker load that measures from 2 to 4 ohms. Keep in mind that heat is the long-term enemy of automotive electronics and the lower your speaker load, the more heat is generated. For low impedance speaker applications or restricted ventilation installations, an external cooling fan may be advisable.

9. Battery and ground connections to the vehicle should be made with crimped ring terminals of the appropriate size (surface area is what counts); soldering the terminals after crimping is also recommended.

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the

RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system.

© 2006 Directed Electronics—all rights reserved

5

6

FRONT PANEL CONNECTIONS/CONTROLS—

XA-3002/XA-6002

NNOOTTEE:: The numbers listed below are referenced on the Input Wiring Diagram.

indicates that the amplifier is on.

7. HHiigghh--PPaassss FFrreeqquueennccyy CCoonnttrrooll - adjusts the frequency (50Hz–500Hz) of the highpass crossover.

2. HHII IInnppuutt (high level input) - Accepts

1v to 10v input from the headunit’s speaker output. The amplifier will automatically wake-up when the input is greater than 1V.

8. BBaassss - sets the bass boost of the high-pass crossover to 0, 5 or 12dB of boost.

3. RRCCAA IInnppuuttss - accepts RCA input from a source unit, preamplifier, or equalizer.

4. LLeevveell CCoonnttrrooll - continuously adjusts from 150mV to 5V for full power output.

pass crossover, full (all pass), or high pass crossover.

the frequency (50Hz–500Hz) of the lowpass crossover.

9. PPRRTT (LED red) - illuminates when the PRT (Protection) function is active. Activates to protect the amplifier when the temperature is too high, the output has a DC offset, a short was detected on the output, or the amplifier power cables have been improperly connected (reverse power). If the temperature, DC offset, or short condition has cleared after approximately 10-seconds the amplifier will automatically recover.

© 2006 Directed Electronics—all rights reserved

INPUT WIRING DIAGRAM—XA-3002/XA-6002

2-CHANNEL XA-3002/XA-6002

1 2 3 4 5 6 7 8 9

PWR

HI-INPUT

INPUT

L

LEVEL

1.5

3 0.8

X-OVER

LOW PASS HI PASS

90 90

5V 0.15V

LPF HPF

FULL

50Hz 500Hz 50Hz

500Hz

BASS

0dB

6dB

12dB

R

PRT

FRONT PANEL CONNECTIONS/CONTROLS—XA-6004

NNOOTTEE:: The numbers listed below are referenced on the Input Wiring Diagram.

indicates that the amplifier is on.

2. RRCCAA IInnppuuttss (front) - accepts RCA input from a source unit, preamplifier, or equalizer.

3. LLeevveell CCoonnttrrooll (front) - continuously adjusts from 250mV to 5V for full power output.

adjusts the frequency

(50Hz–500Hz) of the low-pass crossover.

HHiigghh--PPaassss FFrreeqquueennccyy CCoonnttrrooll (front) adjusts the frequency

(50Hz–500Hz) of the high-pass crossover.

4. HHII IInnppuutt (high level input) - Accepts

1v to 10v input from the headunit’s speaker output. The amplifier will automatically wake-up when the input is greater than 1V.

5. LLeevveell CCoonnttrrooll (rear) - continuously adjusts from 250mV to 5V for full power output.

© 2006 Directed Electronics—all rights reserved

7

adjusts the frequency

(50Hz–500Hz) of the low-pass crossover.

HHiigghh--PPaassss FFrreeqquueennccyy CCoonnttrrooll (rear) adjusts the frequency

(50Hz–500Hz) of the high-pass crossover.

6. RRCCAA IInnppuuttss (rear) - accepts RCA input from a source unit, preamplifier, or equalizer.

7. PPRRTT (LED red) - illuminates when the PRT (Protection) function is active. Activates to protect the amplifier when the temperature is too high, the output has a DC offset, a short was detected on the output, or the amplifier power cables have been improperly connected (reverse power). If the temperature, DC offset, or short condition has cleared after approximately 10-seconds the amplifier will automatically recover.

low pass crossover, full (all pass), or high pass crossover.

9. BBaassss (front) - sets the bass boost of the high-pass crossover to 0, or 8dB of boost.

10. BBaassss (rear) - sets the bass boost of the high-pass crossover to 0, or 8dB of boost.

low pass crossover, full (all pass), or high pass crossover.

8

© 2006 Directed Electronics—all rights reserved

INPUT WIRING DIAGRAM—XA-6004

4-CHANNEL XA-6004

FRONT REAR

1 2 3 4 5 6

PWR

INPUT

LF

4

LEVEL

1.4

0.5

FRONT

LOW PASS

90

HI PASS

90

5V 0.25V

50Hz 500Hz 50Hz

LPF

FULL

HPF

500Hz

0dB

HI-INPUT

8dB

0dB

RF

X-OVER

BASS BASS

REAR

HI PASS LOW PASS

90 90

4

LEVEL

1.4

0.5

INPUT

LR

PRT

50Hz 500Hz 50Hz 500Hz 5V 0.25V

8dB

LPF

FULL

HPF

X-OVER

RR

8 9 10 11

7

FRONT PANEL CONNECTIONS/CONTROLS—

XA-5001/XA-8001

NNOOTTEE:: The numbers listed below are referenced on the Input Wiring Diagram.

indicates that the amplifier is on.

2. HHII IInnppuutt (high level input) - Accepts

1v to 10v input from the headunit’s speaker output. The amplifier will automatically wake-up when the input is greater than 1V.

3. RRCCAA OOuuttppuutt - RCA output to another amplifier.

4. RRCCAA IInnppuuttss - accepts RCA input from a source unit, preamplifier, or equalizer.

5. LLeevveell CCoonnttrrooll - continuously adjusts from 150mV to 5V for full power output.

pass crossover, or full (all pass).

the frequency (30Hz–250Hz) of the lowpass crossover

© 2006 Directed Electronics—all rights reserved

9

10

8. BBaassss - sets the bass boost of the high-pass crossover to 0, 6 or 12dB of boost.

9. PPRRTT (LED red) - illuminates when the PRT (Protection) function is active. Activates to protect the amplifier when the temperature is too high, the output has a DC offset, a short was detected on the output, or the amplifier power cables have been improperly connected (reverse power). If the temperature, DC offset, or short condition has cleared after approximately 10-seconds the amplifier will automatically recover.

INPUT WIRING DIAGRAM—XA-5001/XA-8001

MONO CHANNEL XA-5001/XA-8001

1 2 3 4 5 6 7 8 9

PWR

HI-INPUT

OUTPUT INPUT

L

3

LEVEL

1.5

0.8

X-OVER

LPF FULL

5V 0.15V

LOW PASS

50

BASS

30Hz 250Hz

0dB 12dB

6dB

R

PRT

© 2006 Directed Electronics—all rights reserved

REAR PANEL CONNECTIONS—XA-3002/XA-6002

NNOOTTEE:: The numbers listed below are referenced on the Speaker Wiring Diagram.

10. SSppeeaakkeerr CCoonnnneeccttiioonnss - Note that the two speakers & four speakers have been connected to the four terminal following the (+) and (-) graphic.

Your speaker terminal may be marked (+) and (-) or there may be red dot by one terminal which means the same as (+).

Connecting the speakers in this manner assures that the two speaker cones will move in and out together according to the original recording. If one of the two speakers is reversed, stereo imaging and bass response will be degraded.

Refer to the specifications for the wire size to be used with your amplifier.

11. AATTCC FFuusseess - protects the amplifier from over current situations. See specification for fuse size for your amplifier. NNoottee:: The XA-3002 has only one fuse.

terminal through a FUSE or CIRCUIT

BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery. Refer to the specifications for the wire size to be used with your amplifier.

or circuit breaker of the appropriate size within

12 inches of the battery terminal connection.

turns on the amplifier when (+) 12 volt is applied to it. Connect it to the remote turn on lead of the head unit or signal source. If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter

(P/N #55000) can be used to supply a remote turn on signal. DO

NOT connect this terminal to constant (+) 12 volt.

GGrroouunndd -- Connect this terminal directly to the sheet metal chassis of the vehicle using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+)

12 volt power wire. The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points.

© 2006 Directed Electronics—all rights reserved

11

12

SPEAKER WIRING DIAGRAM—XA-3002/XA-6002

2-CHANNEL XA-3002/XA-6002

SPEAKER

4 Ohm

SPEAKER

4 Ohm

Note: Model XA-3002 has one fuse.

(R-)

BRIDGED

(R+) (L-) (L+) FUSE FUSE

+12V REM GND

10 11 12

For bridging into a single speaker load, the XA-3002/6002 have the ability to be bridged, as shown in the diagram below:

2-CHANNEL XA-3002/XA-6002 BRIDGED

SPEAKER

4 Ohm

(R-)

BRIDGED

(R+) (L-) (L+)

FUSE FUSE

+12V REM GND

© 2006 Directed Electronics—all rights reserved

SPEAKER WIRING DIAGRAM—XA-6004

4-CHANNEL XA-6004

RIGHT

SPEAKER

4 Ohm

FRONT

LEFT

SPEAKER

4 Ohm

RIGHT

SPEAKER

4 Ohm

FRONT

REAR

(R-)

BRIDGED

(R+) (L-) (L+)

FUSE FUSE

(R-)

(R+) (L-) (L+)

10 11

LEFT

SPEAKER

4 Ohm

+12V REM GND

12

REAR

For bridging front and rear into single speaker loads, the XA-6004 has the ability to be bridged as shown in the diagram below:

© 2006 Directed Electronics—all rights reserved

13

4-CHANNEL XA-6004 BRIDGED

FRONT

SPEAKER

4 Ohm

SPEAKER

4 Ohm

FRONT

REAR

(R-)

BRIDGED

(R+) (L-) (L+)

FUSE FUSE

(R-) (R+) (L-) (L+)

+12V REM GND

REAR

14

© 2006 Directed Electronics—all rights reserved

SPEAKER WIRING DIAGRAM—XA-5001/XA-8001

The XA-5001, and XA-8001 amplifiers offer two positive and two negative output terminals for ease of connecting the speakers to the amplifier. Since these are mono amplifiers, the speaker connectors are paralleled internally. Each amplifier is stable to 2 ohms.

MONO XA-6004

SPEAKER

4 Ohm

( - )

( - ) ( + )

( + )

FUSE FUSE

+12V

REM GND

10 11 12

SPEAKER

4 Ohm

NNOOTTEE!! The XA-5001 and XA-8001 are not designed to work in a bridged or strapped configuration. Attempting to apply these configurations will damage the amplifier and will not be covered under warranty.

© 2006 Directed Electronics—all rights reserved

15

16

HIGH LEVEL HARNESSES

NNOOTTEE!!

Do not connect the high level input connections to power, signal, or chassis ground as damage to the head-unit outputs may result. The high-level inputs are designed to work with either grounded or BTL speaker level outputs (found on most head units).

NNOOTTEE!!

Also, to preclude the use of the High Level Harness, a speaker level to

RCA adapter is available (Directed p/n 55020) to convert any regular or high-powered speaker output to a preamp level, high impedance signal to drive the amplifier.

33000022,, 66000022,, 55000011,, 88000011 HHiigghh LLeevveell CCoonnnneeccttiioonnss

Wire Color

WHITE/BLACK

BLACK

WHITE

GRAY/BLACK

GRAY

Input Connection

- Left channel

Ground

+ Left channel

- Right channel

+ Right channel

66000044 HHiigghh LLeevveell CCoonnnneeccttiioonnss

Wire Color

WHITE

WHITE/BLACK

BLACK

GREEN/BLACK

GREEN

GRAY

GRAY/BLACK

VIOLET/BLACK

VIOLET

Input Connection

+ Left Front channel

- Left Front channel

Ground

- Right Rear channel

+ Right Rear channel

+ Right Front channel

- Right Front channel

- Left Rear channel

+ Left Rear channel

© 2006 Directed Electronics—all rights reserved

CROSSOVER SETTINGS AND GAIN ADJUSTMENT

Your Xtreme Series power amplifier by Directed Audio needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier.

„

For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be set to FLAT. If the amplifier is driving your subwoofers, set the switch to LPF, and for mid-bass/midrange output, set to HPF.

„

The crossover frequency control needs to be adjusted to suit your particular system.

For subwoofer applications, try to keep the setting low enough to prevent the image smearing (you should not be able to hear male voices from the subwoofer) but not so low as to create a gap between the subwoofer and the midbass/midrange speakers. For mid-bass/midrange settings, try to keep the setting low enough to keep your sound stage in front of you, without overdriving the speaker. It will be to your advantage to spend some extra time with this adjustment, listening to familiar music or system set-up discs to achieve the kind of musical reproduction that you prefer.

„

The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain setting on the amplifier and start to raise the head unit volume again.

When you can listen to the music at or slightly above 3/4 on your head unit without audible distortion, slowly raise the gain of the amplifier until distortion is heard, then back off the gain until the distortion is not audible. This setting will allow you to reach full output with all but the quietest of source material, while avoiding excessive noise in the system.

„

The same procedure should be used for adjusting the amplifier when the on-board crossover is set to LPF or HPF, but you will also have to take into consideration the effect that gain adjustment has on system frequency response and imaging.

Again, plan on spending some time with music that you know, getting the gain and crossover settings the way you like. Test discs and analyzers may help with this process, but in the end it's your ears that count - listen to the music!

© 2006 Directed Electronics—all rights reserved

17

18

CEA SPECIFICATIONS

XA-3002

Power Output: 55 Watts RMS x 2 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 80 Watts RMS x 2 at 2 ohms and < 1% THD+N

XA-6002

Power Output: 100 Watts RMS x 2 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 150 Watts RMS x 2 at 2 ohms and < 1% THD+N

XA-6004

Power Output: 60 Watts RMS x 4 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -75 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 75 Watts RMS x 4 at 2 ohms and < 1% THD+N

XA-5001

Power Output: 150 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -75 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 250 Watts RMS x 1 at 2 ohms and < 1% THD+N

XA-8001

Power Output: 300 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -75 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 400 Watts RMS x 1 at 2 ohms and < 1% THD+N

© 2006 Directed Electronics—all rights reserved

SPECIFICATIONS

Xtreme models XA-3002 XA-6002 XA-6004 XA-5001 XA-8001

Type

Maximum Power

Damping Factor

Frequency Response

Crossover (12dB Slope)

Bass Boost (@ 50Hz)

Input Sensitivity

Protection

Fuse Size 25A x 1

Min. Speaker Wire Gauge 12

Min. Power Wire Gauge 8

2-channel

300 watts

2-channel

600watts

4-channel

600 watts

Mono block Mono block

500 watts

>50

800 watts

>50 >150 >150 >75

20Hz-20kHz 20Hz-20kHz 20Hz-20kHz 20Hz-250Hz 20Hz-20kHz

+0, -3dB +0,-3dB +0,-3dB +0,-3dB +/- 1dB

LP 50-500Hz LP 50-500Hz LP 50-500Hz LP 30-250Hz LP 30-250Hz

Switch Switch Switch

0, +6, +12dB 0, +6, +12dB +0, +8dB

Switch

0, +6, +12dB

Switch

0, +6, +12dB

150mV-5V 150mV-5V 250mV-5V

Thermal, Overcurrent, Short Circuit, Reverse Polarity

150mV-5V 150mV-5V

20A x 2

12

8

25A x 2

12

8

20A x 2

12

8

30A x 2

12

4

19

© 2006 Directed Electronics—all rights reserved

© 2006 Directed Electronics - All rights reserved - G43100/05/10/15/20 04-06

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals