Dish Network 121716 Universal Remote User Manual

inside_front_cover_dishpvr.fm Page 0 Tuesday, February 11, 2003 2:17 PM
REGULATORY FACTORS
WIRELESS REMOTE CONTROL
This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications to this device may void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experience radio/TV technician for help.
SAFETY INSTRUCTIONS
You must keep safety in mind while using this device. Keep these
and any other instructions for future reference.
INSTALLATION
Observe Warnings: Carefully follow all warnings on the device
and in the operating instructions.
Heat: DO NOT place the device near heat sources such as radiators, stoves, heat
registers, or other appliances that produce heat.
C ARE
AND
USE
Cleaning: DO NOT use liquid, abrasive, solvent, or aerosol cleaners. Use a damp cloth
for cleaning.
When Not in Use: Remove the batteries if this device is to be
left unattended or unused for a long period of time.
Refer servicing to qualified personnel when a solid object
or liquid has fallen onto or into the device.
DO NOT attempt to service this device. Refer all
servicing to qualified personnel. Opening covers other
than the battery cover will void the warranty.
text_dishpvr.fm Page 1 Friday, February 28, 2003 1:22 PM
CONTENTS OF THIS USER GUIDE
Remote Control Basics ....................................... 2
Remote Control Batteries.................................... 2
Remote Control Signals: UHF and IR ................. 3
Install an Attenuator ............................................ 4
Remote Control Modes ....................................... 5
Remote Control Setup ........................................ 6
Set Up the Remote Control ................................. 6
Setting Up to Control Other Devices .... 6
Scan for Device Codes......................... 7
Check the Device Codes ...................... 8
Change the Address ........................................... 9
Switch Between TV and Device
Volume Control.................................................. 10
Remote Control Buttons ................................... 11
Control the Receiver ..........................................11
Control a TV (or a Second TV).......................... 17
Control a VCR (Second VCR or a DVD Player) 20
Control a Cable TV Box .................................... 22
Control a Tuner or Amplifier .............................. 24
Device Codes .................................................... 26
TV Codes .......................................................... 26
VCR Codes ....................................................... 28
Cable TV Box Codes......................................... 29
DVD Player Codes ............................................ 30
Tuner/Amplifier Codes....................................... 30
Troubleshoot the Remote Control ................... 31
Limited Warranty ............................................... 33
If You Need Help ................................................ 35
Index ................................................................... 36
121716
1
text_dishpvr.fm Page 2 Friday, February 28, 2003 1:22 PM
REMOTE CONTROL BASICS
This remote control gives you easy access to all the features
of a DISH Network satellite TV receiver and lets you control PVR
features of a DISH Network DishPVR satellite receiver. These PVR
features let you record programming with full digital quality,
without a VCR.
You can set up the remote to control the satellite TV receiver and up to
three other devices. These devices can be a TV, a VCR or DVD player,
and a third device.
R EMOTE CONTROL BATTERIES
The remote control requires AAA batteries.
When you replace old batteries, you should
replace all of the batteries. Use batteries of
the same kind, for example, alkaline or
carbon zinc, and don’t mix batteries of
different kinds. Alkaline batteries last longer.
1. Press down on the battery cover’s
top latch and lift the cover off.
2. Take out all of the old batteries.
3. Put the new batteries in. Make sure
you match the plus (“+”) ends with the
plus markings on the battery case.
4. Fit the battery cover’s bottom tab
back into the slot at the bottom of the
battery case, and snap the cover back
into place.
2
121716
text_dishpvr.fm Page 3 Friday, February 28, 2003 1:22 PM
R EMOTE CONTROL SIGNALS: UHF
AND
IR
The remote control uses both Ultra High Frequency (UHF) radio
signals and Infrared (IR) light signals to control the receiver
but uses only IR signals to control other devices.
• IR signals travel only short distances (40 feet or less),
and can’t go through walls or other solid objects.
You must point the remote control right at the device
you want to control, with no objects to block the signal path.
• UHF signals travel long distances (100 feet or more) and can
go through walls and other solid objects. Because UHF signals
travel so far, the receiver may respond to signals from other
nearby remote controls. To handle this problem, see Change the
Address on page 9. If this doesn’t work, see Install an Attenuator
on page 4.
• You need to attach the UHF remote antenna to the receiver’s
back panel UHF REMOTE ANTENNA input so you can use the
UHF capabilities of the remote (as shown in the diagram below).
Note: Set the antenna straight up so you can use the remote
from as far away as possible. Don’t let the antenna touch
anything.
Note: If you don’t attach the antenna, you can still use the remote
to control the receiver at short distances. This is because
the remote sends both IR and UHF signals to the receiver.
121716
3
text_dishpvr.fm Page 4 Friday, February 28, 2003 1:22 PM
INSTALL AN A TTENUATOR
Stray UHF signals can block signals from the remote control
to the receiver. To prevent blocks, you can install a 10 dB attenuator
(you can buy one from a consumer electronics parts store).
Note: This will help keep out stray UHF signals, but also cut down
how far away you can use the remote control.
1. Take the UHF antenna off
of the receiver’s back panel
UHF REMOTE ANTENNA
input.
2. Put a 10 dB attenuator onto the
UHF REMOTE ANTENNA
input.
3. Put the UHF antenna onto the
attenuator.
4
121716
text_dishpvr.fm Page 5 Friday, February 28, 2003 1:22 PM
REMOTE CONTROL MODES
R EGULAR MODES
You can set the remote to four different modes to control the receiver
or other devices.
Set up the remote to control a device like a TV or a VCR. See Set Up
the Remote Control on page 6 for what to do.
Note: The remote comes already set up to control the receiver, unless
you have changed the address on your receiver.
Use the remote control’s mode buttons, SAT (“satellite” receiver), TV,
VCR (for a VCR or a DVD player), and AUX (“auxiliary,” for a cable
TV box, a tuner, a second TV, a second VCR, a DVD player, or an
audio amplifier) to set the remote to the right mode for the device. To
change the mode, press the button for the device you want the remote
to control. The mode button stays lit for two seconds to show you’ve
set the remote to that mode.
LIMITED MODE
You can program your remote control in limited mode to keep from
accidentally changing the channel on your TV or VCR. When you use
the remote to control your TV in limited mode, you will only be able to
use the POWER, MUTE, and VOLUME buttons. Also, when you use
the remote to control your VCR in limited mode, you will only be able
to use the POWER and VCR function buttons. Set Up the Remote
Control on page 6 has a step that tells the remote control to go into
limited mode.
Note: Limited mode is not used with cable boxes or amplifiers.
121716
5
text_dishpvr.fm Page 6 Friday, February 28, 2003 1:22 PM
REMOTE CONTROL SETUP
SET UP THE REMOTE CONTROL
On the next few pages we tell you how to set up the remote to control
a TV, a VCR, or other devices.
When you get the remote it’s already set up to control the
receiver, unless you have changed the address on your
receiver. However, you must set up the remote to control
the TV before you can use the MUTE and VOLUME
buttons. To set up the remote control, you can either
follow the directions in Setting Up to Control Other
Devices below or Scan for Device Codes on page 7.
SETTING U P TO C ONTROL OTHER D EVICES
You can set up the remote to control other devices using the device
codes listed on page 26. Here’s what to do:
1. Use the device’s buttons or its remote control to turn the
device on.
2. Find the brand name of the device in the tables starting on
page 26.
If the brand isn’t listed, see Scan for Device Codes on page 7.
3. Press and hold the mode button for the device you want
the remote to control, for about three seconds. When all the
other mode buttons light up, let go of the mode button - that
mode button should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light
will flash.
4. Only for the AUX mode, use the NUMBER PAD to enter 0 for
a second TV, or 1 for a second VCR, or 2 for a tuner, amplifier,
or cable box.
For any other mode, skip to step 5.
5. Use the number buttons to enter one of the
device codes from the table.
6. Only for limited mode, press 1.
Note: If you want to use all of the remote
control’s features in TV mode, reprogram the
remote control following these instructions
but skip this step.
6
121716
text_dishpvr.fm Page 7 Friday, February 28, 2003 1:22 PM
7. Press the POUND (#) button. If you entered the code
correctly, the mode button flashes three times.
8. Press the blank POWER button to test if the code
works for the device. If it does, the device should
turn off.
9. Turn the device back on and try some other buttons
to make sure they work. Sometimes, the blank POWER button
works when other buttons don’t. If the code works for other
buttons, stop here.
10.If the code you entered doesn’t work, do steps 3 through 9 again
with another device code from the tables.
11. If you cannot find a code that works, try Scan for Device Codes
below.
SCAN FOR D EVICE CODES
If the code for your device is not listed in the tables starting on page 26,
use this procedure to scan the remote control’s memory for the device
code. Here’s what to do:
1. Use the device’s buttons or its remote control to turn the
device on.
2. Press and hold the mode button for the device you want the
remote to control, for about three seconds. When all the other
mode buttons light up, let go of the mode button - that mode
button should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light
will flash.
3. Only for the AUX mode, use the number buttons
to enter 0 for a second TV, 1 for a second VCR,
or 2 for a tuner, amplifier, or cable box. Then press
the STAR (*) button.
For any other mode, skip to step 4.
121716
7
text_dishpvr.fm Page 8 Friday, February 28, 2003 1:22 PM
4. Press the blank POWER button.
5. Press the UP or DOWN ARROW button until
the device turns off. You will have to do this
repeatedly to scan through all codes.
Note: Do not press the ARROW buttons too
quickly because you could skip over the code
for your device.
Note: The mode button for the device will flash rapidly eight
times when you’ve scanned all the codes for that device.
6. If the remote reaches the correct code, the device
turns off. When this happens, press the POUND (#)
button to store the code in the remote.
7. Press the blank POWER button to turn the device
back on.
8. Try some other buttons to make sure they work.
Sometimes, the blank POWER button works
when other buttons don’t.
CHECK THE D EVICE CODES
You can find out what device code you’ve set for each remote control
mode. Here’s what to do:
1. Press and hold the mode button for the device you want the
remote to control, for about three seconds. When all the other
mode buttons light up, let go of the mode button - that mode
button should now be flashing.
For example, hold the TV mode button for a TV until all of the
other mode buttons light. When you let go, the TV mode light
will flash.
2. Press the POUND (#) button twice. The mode button
flashes the number for each digit of the device code,
with a pause between the groups of flashes. A quick
flash is for zero. For example, if the code is 570, the
mode button flashes five times, pauses, flashes seven times,
pauses, and flashes once quickly.
8
121716
text_dishpvr.fm Page 9 Friday, February 28, 2003 1:22 PM
For AUX mode, the first group of flashes tells you what the
AUX mode controls. A quick flash (zero) before the three-digit
code is for a TV; one regular flash is for a VCR; and two flashes
is for a tuner, amplifier, or cable box. For example, if the TV
code is 570, the AUX mode button flashes once quickly, pauses,
flashes five times, pauses, flashes seven times, pauses, and
flashes once quickly.
CHANGE THE ADDRESS
Because UHF signals travel long distances and go through walls,
a neighbor’s remote may control your receiver by mistake. To handle
this problem, you can change the remote control and receiver address.
1. Open the Important System Information screen.
Press the receiver’s front panel SYSTEM INFO
button.
The Important System Information screen shows
a Remote Address.
Write down this number:
2. Press and hold the SAT mode button about three
seconds, until all the mode buttons light up,
and then let go of the SAT button. The SAT mode
button will blink.
3. Use the number buttons to enter any number
from 1 to 16, but not the one you found in step 1. The SAT
mode button goes out after you enter each digit, and then lights
up again.
Write down the number you entered:
4. Press the POUND (#) button.
If you entered the address correctly, the SAT mode
button will flash three times.
5. Press the RECORD button.
6. Make sure the Remote Address on the Important
System Information screen now is the same as the
one you entered in step 3. If it isn’t, the remote can’t
control the receiver.
7. To check the remote control address, press and hold
the SAT mode button for three seconds. Then, let go
of the SAT button, and press the POUND (#) button
twice. The SAT mode button flashes the same number
of times as the address you entered in step 3.
121716
9
text_dishpvr.fm Page 10 Friday, February 28, 2003 1:22 PM
8. Press the SELECT button to close the
Important System Information screen.
SWITCH BETWEEN TV
AND
DEVICE VOLUME C ONTROL
When you set up the remote to control a TV, the MUTE and VOLUME
buttons control the TV volume. However, if you want to use the AUX
mode to control a tuner or amplifier and the device has a volume
setting, you can set up the remote to control the device’s volume
instead of the TV volume.
To set the remote to control the device’s volume:
1. Press and hold the AUX mode button
for three seconds, and then let go of it. The AUX mode
button will blink.
2. Press the POUND (#) button.
3. Press the plus (+) side of the VOLUME
button.
4. Press the 0 number button.
5. Press the POUND (#) button.
The AUX mode button flashes three times.
6. Press the SAT mode button.
7. Press the plus (+) and minus (-) sides of the VOLUME
button.
The device’s volume changes and the AUX mode
button lights instead of the TV mode button.
To set the remote back to control the TV volume:
1. Press and hold the TV mode button
for three seconds, and then let go of it. The TV mode
button will blink.
2. Press the POUND (#) button.
3. Press the plus (+) side of the VOLUME
button.
10
121716
text_dishpvr.fm Page 11 Friday, February 28, 2003 1:22 PM
4. Press the 0 number button.
5. Press the POUND (#) button.
The TV mode button flashes three times.
6. Press the SAT mode button.
7. Press the plus (+) and minus (-) sides of the VOLUME
button.
The TV’s volume changes and the TV mode button lights
instead of the AUX mode button.
REMOTE CONTROL BUTTONS
C ONTROL THE RECEIVER
SAT M ODE BUTTON
Press this button to set the remote to SAT (“satellite”) mode to control
the receiver. The SAT mode button’s back light stays lit for about two
seconds to show you’ve set the remote to SAT mode. Make sure you
keep the remote in SAT mode to use the buttons described here.
TV/VIDEO B UTTON
If you connect the receiver with its back panel TV ANTENNA/CABLE
IN and TV SET OUT ports, use this button to switch the receiver
between the satellite signal (connect it to the SATELLITE IN port) and
another video signal like a cable or broadcast TV antenna input
(connect it to the receiver’s TV ANTENNA/CABLE IN input).
Note: If you connect the receiver to other devices with the phono
(RCA) jacks or the S-VIDEO output, you must use the TV
menus to change the input from local broadcast TV to satellite
TV.
121716
11
text_dishpvr.fm Page 12 Friday, February 28, 2003 1:22 PM
P OWER B UTTONS
Press the blank POWER button to turn the receiver on or off. The
POWER light on the receiver’s front panel turns on to show the
receiver is on, and turns off to show it’s off.
MENU BUTTON
Press this button to open the Main Menu.
PAGE UP AND PAGE DOWN BUTTONS
Press the PAGE UP button or the PAGE DOWN button to scan, page
by page, through the Program Guide, a Themes list, a Favorite
List, an Event Timers list, or a list of channels.
Note: An “event” is any satellite program.
GUIDE BUTTON
Press this button to open the Program Guide. When you have the
Program Guide open, press this button to change between your
Favorite Lists.
12
121716
text_dishpvr.fm Page 13 Friday, February 28, 2003 1:22 PM
ARROW B UTTONS
• Change channels - Press the UP or DOWN arrow button to
change channels.
• Open the Browse Banner - Press the RIGHT arrow button.
• Show Themes - Press the LEFT arrow button.
• Move around within the Program Guide, menus, and Browse
Banner - Press the UP, DOWN, LEFT, and RIGHT arrow
buttons.
S ELECT BUTTON
Press this button to select the option you highlight in a menu.
RECALL BUTTON
Press this button to go back to the last receiver channel you watched.
Press it again to switch between the last two receiver channels you
watched.
INFO BUTTON
• Program information - Press the INFO button for more
information when you watch a program, or when you have the
Program Guide, Browse Banner, or Themes list open.
• Help - Press the INFO button to see help information when a
Help button appears in a menu.
121716
13
text_dishpvr.fm Page 14 Friday, February 28, 2003 1:22 PM
VIEW B UTTON
• When you watch a program, press this button to briefly display
the Program Banner.
• When you use a menu, press this button to cancel
and go back to watch a program.
C ANCEL BUTTON
Press this button to cancel and go back to the previous menu or to
watch a program.
D ISHPVR B UTTONS
Use these buttons to record or play back a program.
• Press the PVR button to open the DishPVR
Recorded Events menu.
• Press the SKIP BACK button to:
• Skip back about ten seconds in a program. Press
this button again to skip back again.
• Use the frame reverse feature. Press the PAUSE
button and then press the SKIP BACK button to
reverse the recording one frame at a time.
• Skip back one day at a time in the Electronic Program Guide
(EPG).
Note: The SKIP BACK button will not skip back the EPG
beyond the current date.
• Press the SKIP AHEAD button to:
• Skip ahead about 30 seconds in a program. Press
this button again to skip ahead again.
14
121716
text_dishpvr.fm Page 15 Friday, February 28, 2003 1:22 PM
• Use the frame advance feature. Press the PAUSE button and
then press the SKIP AHEAD button to advance the recording
one frame at a time.
• Skip ahead one day at a time in the EPG.
• Press the BACK button to:
• Move back through a program four times as
fast as normal play. Press this button twice to
move back at 15 times, three times to move
back at 60 times, and four times to move back
at 300 times as fast as normal play.
• Use the slow motion feature. Press the PAUSE button and
then press the BACK button to reverse the program in slow
motion. Press the BACK button once to reverse the program
1/4 the speed as normal play. Press the BACK button twice to
reverse at normal speed.
• Press the PAUSE button to pause a program.
Press this button again to go back to watching
the program.
• Press the FWD (“forward”) button to:
• Move ahead through a program four times as
fast as normal play. Press this button twice to
move ahead at 15 times, three times to move
ahead at 60 times, and four times to move
ahead at 300 times as fast as normal play.
• Use the slow motion feature. Press the PAUSE button and
then press the FWD button to forward the program in slow
motion. When you press the FWD button once the program
advances at 1/15 the speed of normal play. Press the FWD
button twice to forward at 1/4 as fast as normal play. Press the
FWD button three times to play the program.
• Press the STOP button to stop recording a program or
to stop playing a recorded program.
• Press the PLAY button to watch a program. Also,
press this button to switch from forward or reverse
back to watch the program at normal speed.
121716
15
text_dishpvr.fm Page 16 Friday, February 28, 2003 1:22 PM
• Press the RECORD button to start recording a
program.
Note: You also use this button if you change
the remote control address. See page 9.
DISH BUTTON
Press the dish button to go to Dish Home for receivers that support
Dish Home.
N UMBER B UTTONS
• Change the channel - Use the NUMBER buttons to enter a
channel number to change the channel. If you have the Program
Guide open, use the NUMBER buttons to jump to the channel
listing on the Program Guide.
• Scroll through the Program Guide by time - When you have
the Program Guide open, enter a number of hours using these
buttons, and then press the RIGHT or LEFT arrow button to skip
the Program Guide forward or backward that many hours.
Enter menu options - For an option with a number, you can press
the number for that option instead of highlighting and selecting
the option.
• Enter numbers in a blank - Highlight the place where you need to
enter the number. Press a number button(s) (or, you can use the
UP/DOWN arrow buttons to enter the number).
16
121716
text_dishpvr.fm Page 17 Friday, February 28, 2003 1:22 PM
• Search - Use the letters above the NUMBER buttons while in the
Search menu. For example, when looking for the channel and
times to watch Rudy Fremmel Presents, you press 7 three times
for an R, 8 two times for a U, 3 one time for a D, and 9 three
times for a Y to spell the word “Rudy” (see your receiver’s User
Guide for more information).
ZERO BUTTON
Press this button to forward space while using the search function of
your receiver.
STAR (*) BUTTON
Press this button to back space while using the search function of your
receiver.
P OUND (#) BUTTON
Press this button to display the Search screen. Also, you use this
button in several procedures in this User Guide.
C ONTROL A TV (OR A SECOND TV)
Only the buttons we tell you about here control a
TV. Some of the buttons we tell you about here
may not control your TV. See your TV user’s manual for
information about the TV’s features.
You can set up the remote to control a second TV
in AUX mode, the same way it controls the first TV
in TV mode. See Set Up the Remote Control
on page 6.
121716
17
text_dishpvr.fm Page 18 Friday, February 28, 2003 1:22 PM
TV MODE BUTTON
You must first set up the remote to control the TV. See Set Up the
Remote Control on page 6. Then press the TV mode button to set the
remote to TV mode. The TV mode button will stay lit for two seconds
to show you’ve set the remote to TV mode. Make sure you keep the
remote in TV mode to use the buttons we tell you about here.
P OWER B UTTONS
Press either POWER button to turn the TV on or off.
Note: If you set up the remote to control one TV in TV mode and an
additional TV in AUX mode, pressing the TV POWER button controls
only the TV you set up in TV mode.
TV/VIDEO B UTTON
If the TV has video input options, use this button to switch the TV
video input.
MUTE BUTTON
Press this button to turn the TV sound on or off.
VOLUME BUTTON
Press this button to raise (+) or lower (-) the TV sound volume.
18
121716
text_dishpvr.fm Page 19 Friday, February 28, 2003 1:22 PM
UP/DOWN ARROW BUTTONS
Use these buttons to change channels on the TV.
Note: These buttons do not change the channels on the TV if the
remote control is in limited mode.
S ELECT BUTTON
The SELECT button works as the ENTER button for a TV.
RECALL B UTTON
Press this button to go back to the last TV channel you watched. Press
it again to switch between the last two TV channels you watched.
NUMBER B UTTONS
Use these buttons to directly enter a different channel.
Note: These buttons do not change the channels on the TV if the
remote control is in limited mode.
121716
19
text_dishpvr.fm Page 20 Friday, February 28, 2003 1:22 PM
CONTROL A VCR (OR A SECOND VCR OR A DVD
PLAYER)
Only the buttons we tell you about here control a
VCR or DVD. Some of the buttons we tell you about here
may not control your VCR. See your VCR’s
user’s manual for information about the VCR’s features.
You can set up the remote to control a second VCR
in AUX mode, the same way it controls the first VCR
in VCR mode. See Set Up the Remote Control
on page 6.
VCR MODE B UTTON
You must first set up the remote to control the VCR. See Set Up the
Remote Control on page 6. Then press the VCR mode button to set the
remote to VCR mode. The VCR mode button will stay lit for two
seconds to show you’ve set the remote to VCR mode. Make sure you
keep the remote in VCR mode to use the buttons we tell you about
here.
You must put the remote in VCR mode to set it up to
control a DVD player. Later, you must put the remote in
VCR mode to use it to control a DVD player.
TV/VIDEO B UTTON
Use this button to switch the VCR between its TV mode and its VCR
mode (see your VCR user’s manual for information).
P OWER B UTTON
Press the blank POWER button to turn the VCR on or off. Press the
TV POWER button to turn the TV on or off.
20
121716
text_dishpvr.fm Page 21 Friday, February 28, 2003 1:22 PM
UP/DOWN ARROW B UTTONS
Use these buttons to change channels on the VCR.
Note: If you are using the remote control in Limited Mode, the TV
will not change channels.
VCR BUTTONS
• Press the BACK button to rewind a videotape.
• Press the PAUSE button to pause a videotape.
Press this button or the PLAY button to play the tape.
• Press the FWD (“forward”) button
to forward a videotape.
• Press the STOP button to stop playing
or recording on a videotape.
• Press the RECORD button to record
on a videotape.
• Press the PLAY button to play a videotape.
121716
21
text_dishpvr.fm Page 22 Friday, February 28, 2003 1:22 PM
C ONTROL A C ABLE TV BOX
Only the buttons we tell you about here control a
cable TV box. Some of the buttons we tell you
about here may not control your cable TV box.
See your cable box user’s manual for information
about the box’s features.
AUX MODE BUTTON
You must first set up the remote to control the cable TV box. See Set
Up the Remote Control on page 6. Then press the AUX mode button to
set the remote to AUX mode. The AUX mode button will stay lit for
two seconds to show you’ve set the remote to AUX mode. Make sure to
keep the remote in AUX mode to use the buttons we tell you about
here.
TV/VIDEO B UTTON
Use this button to switch the cable box between its TV mode and its
video mode.
P OWER B UTTON
Press the blank POWER button to turn the cable box on or off. Press
the TV POWER button to turn the TV on or off.
M UTE BUTTON
Press this button to turn on or off the sound from the cable box.
Note: Program the remote to control the device’s volume by following
the instructions on page 10.
22
121716
text_dishpvr.fm Page 23 Friday, February 28, 2003 1:22 PM
VOLUME BUTTON
Press this button to raise (+) or lower (-) the sound volume from the
cable box.
Note: Program the remote to control the device’s volume by following
the instructions on page 10.
UP/DOWN ARROW BUTTONS
Use these buttons to change channels on the cable box.
SELECT BUTTON
Press the SELECT button in place of the ENTER button for the
cable box.
RECALL BUTTON
Press this button to go back to the last cable box channel you used.
Press it again to switch between the last two cable box channels you
used.
121716
23
text_dishpvr.fm Page 24 Friday, February 28, 2003 1:22 PM
NUMBER BUTTONS
Use these buttons to enter channel numbers.
C ONTROL A TUNER OR AMPLIFIER
Only the buttons described here control a tuner or
amplifier. Some of the buttons described here may not
control your tuner or amplifier. See the device user’s
manual for information.
AUX M ODE BUTTON
You must first set up the remote to control the device. See Set Up the
Remote Control on page 6. Then press the AUX mode button to set the
remote to AUX mode. The AUX mode button will stay lit for two
seconds to show you’ve set the remote to AUX mode. Make sure to
keep the remote in AUX mode to use the buttons we tell you about
here.
P OWER B UTTON
Press the blank POWER button to turn the tuner or amplifier on or off.
Press the TV POWER button to turn the TV on or off.
24
121716
text_dishpvr.fm Page 25 Friday, February 28, 2003 1:22 PM
MUTE B UTTON
Press this button to turn on or off the sound.
Note: Program the remote to control the device’s volume by following
the instructions on page 10.
VOLUME BUTTON
Press this button to raise (+) or lower (-) the sound volume.
Note: Program the remote to control the device’s volume by following
the instructions on page 10.
UP/DOWN ARROW BUTTONS
Use these buttons to change channels on the tuner or amplifier.
S ELECT BUTTON
This button works as the INPUT SELECT button for the tuner or
amplifier.
121716
25
text_dishpvr.fm Page 26 Friday, February 28, 2003 1:22 PM
DEVICE CODES
These tables contain the manufacturer codes for programming the
remote to control your TV, a VCR, DVD player, cable box, or audio
amplifier. Every attempt has been made to include all codes. If your
device brand is not listed or if the codes to not work, the remote may
not control your device. In some cases codes may operate some but not
all buttons shown in this guide.
TV CODES
TELEVISION
CODES
TELEVISION
Admiral
Akai
Alba
A-Mark
CODES
514, 521
EchoStar
722
Electrohome
526, 573, 709, 713
Elta
532
Emerson
526, 527,
535, 536,
540, 541,
692, 695,
532, 570, 573
613
620
528, 533, 534,
537, 538, 539,
573,622, 691,
696, 699, 720,
Amstrad
533
Anam
509, 541, 620, 621,
691,698
Envision
506, 712
AOC
505, 506, 519, 520, 620,
695, 712
Etron
532
Archer
620
Fisher
542, 590
Audiovox
620
Formenti
611
Bauer
611
Fortress
573, 605
Baycraft
536
Fujitsu
534, 694
Brockwood
695
Funai
534, 541, 691, 694
Broksonic
562, 691
Futuretech
541, 691, 694
Candle
506, 522, 523, 525, 536,
691, 695, 712
General Electric
(GE)
503, 508, 509, 515, 540,
543, 544, 630, 695, 698,
701,714, 715, 716
Capehart
519, 695
Genexxa
613
Circuit City
695
Goldstar
505, 523, 526, 545, 546,
573, 588, 693, 712
Granada
695, 711
Grand
695
Grandiente
711
Grundig
547
Citizen
506, 516, 522, 523, 524,
525, 526, 691, 712
Colortyme
573, 695
Concerto
Contec
Craig
Crown
523
527, 528, 541, 591, 691
536, 541, 691, 694
Hallmark
695
Harmon Kardon
561
526, 536
Curtis Mathes
506, 516, 526, 573, 703,
712, 708
Hinari
534
CXC
541, 691
Hitachi
Daewoo
505, 524, 526, 529, 530,
531, 532, 698, 712, 719
523, 526, 548, 549, 550,
551, 552, 553, 554, 555,
585, 597, 626, 702, 718
Infinity
566
Daytron
526, 695
JBL
566
JC Penney
503, 505, 506, 516, 526,
531, 543, 596, 701, 714
Dixi
Dumont
26
532, 588, 620
695
121716
text_dishpvr.fm Page 27 Friday, February 28, 2003 1:22 PM
TELEVISION
CODES
TELEVISION
CODES
Jenson
556, 573
Philips
566, 588
JVC
557, 558, 559, 560
Pioneer
502, 548, 551, 576, 708
Kawasho
548, 561, 712
Portland
505, 526, 712
Kenwood
506, 573, 712
Proscan
503
Kloss
522, 561, 610, 698
Proton
513, 519, 526, 536, 585,
624, 695
KTV
526, 539, 540, 541, 691,
696, 712
Pulsar
501
Lloyds
695
Quasar
508, 509, 577, 698, 700
Lloytron
526
Radio Shack
526, 541, 607, 612, 691,
698
Loewe
588
RCA
Logik
518
Luxman
523
503, 505, 515,
580, 581, 582,
586, 587, 625,
691, 698, 701,
715, 716
LXI
503, 563, 566, 590, 595,
617, 625, 701
Realistic
590
Magnasonic
573
Saba
551
Magnavox
506, 520, 525, 536, 564,
565, 566, 567, 568, 569,
573, 575, 610, 710, 712
Saisho
532, 533, 609
Sampo
506, 519, 698
Marantz
506, 566, 573, 588, 712
Samsung
Matsui
532, 609
505, 506, 516, 523, 526,
532, 588, 612, 695, 704,
712, 721
Megatron
695
Samwon
620
Memorex
518, 532, 590, 695, 720
Sanyo
542, 589, 590, 591, 592,
609
MGA
504, 505, 506, 571,
573,695
SBR
588
Mitsubishi
504, 505, 570, 571, 572,
597, 623, 695, 705, 707,
712
Schneider
588
Scott
526, 534, 537, 541, 593,
600, 691,696, 701
Sears
503, 523, 534,
589, 590, 594,
598, 599, 601,
604, 617, 695,
Seimitsu
695
Sharp
526, 585, 591, 605, 606,
607, 608, 628, 629
Siemens
591
MTC
505, 506, 516, 523, 531,
695, 712
NAD
502, 617, 695
National
509, 697,698
National Quenties
697
NEC
505, 506, 507, 517, 523,
573, 627, 712
Nikkai
612, 613, 618
Nordmende
551
Normandic
717
Novabeam
561, 698
Nyon
701
Onwa
541, 691
Optonica
605, 607
Orion
694
Osaki
Panasonic
Philco
121716
612
508, 509, 510, 511, 512,
566, 574, 685,
686,687,689, 697, 698,
700, 706, 714, 716
505, 506, 525, 536, 564,
565, 568, 573, 610, 712
548,
583,
633,
708,
579,
584,
634,
714,
542, 563,
595, 596,
602, 603,
703
Signature
518
Silver
573
Solavox
612
Sony
500, 578, 609, 619, 622,
690
Soundesign
525, 536, 541, 691, 695
Spectricon
520, 620
Squareview
694
SSS
505, 541, 573, 691, 712
Supra
523
Supre-Macy
522
Sylvania
506, 525, 536, 564, 565,
566, 568, 573, 575, 600,
610, 611, 712
27
text_dishpvr.fm Page 28 Friday, February 28, 2003 1:22 PM
TELEVISION
CODES
VCR
CODES
Symphonic
632, 692, 694
Audio Dynamics
594, 600
Tandy
605, 613
Broksonic
559
Tatung
509, 698
Bush
589
Technics
508
Candle
580, 592, 593
Techwood
523, 573
Canon
542, 553, 554
Teknika
504, 505, 516, 518, 522,
523, 524, 525, 526, 534,
536, 541, 614, 615, 686,
691, 712
Capehart
543, 546
Teleavia
551
Telefunken
551
Teletech
532
Tera
513
Thomas
695
Thompson
709
Thomson
551, 616
TMK
523, 573, 695
Citizen
591, 592, 593
Craig
591, 608
Croslex
553
Curtis Mathes
554, 592, 605
Daewoo
534, 545, 546, 547, 593
Daytron
546
DBX
594, 600
Dumont
549
Dynatech
588
Electrohome
609
Emerson
505, 506, 507, 508, 509,
510, 511, 512, 559, 568,
588, 590, 609, 618
Toshiba
516, 590, 596, 617, 618,
631, 688
Tosonic
528
Totevision
526
Finlandia
549
Toyomenko
695
Finlux
549, 565, 588
Universal
543
Fisher
548, 549, 584, 588, 608,
610
Vector Research
506
Victor
557
General Electric
(GE)
550, 551, 552, 554, 572,
591, 605
Video Concepts
570, 691
Goldstar
530, 555, 592, 612, 613
Vidtech
505, 695, 712
Goodmans
585, 589
Viking
522
Go Video
557 558, 620
Wards
505, 506, 515, 518, 534,
536, 543, 564, 565, 567,
568, 607, 619, 712, 714,
715
Granada
549, 581
Yamaha
505, 506, 712
York
695
Zenith
501, 518, 693
Zonda
620
VCR C ODES
VCR
CODES
Grundig
565
Harmon Kardon
530, 569
Hinari
589
Hitachi
536, 537, 538, 539, 540,
541, 553, 588, 595, 596,
597
Instant Replay
553
ITT
518
JC Penney
530, 554, 580, 591, 594,
600, 601
Jenson
560
Aiwa
588, 622, 623, 624
JVC
561, 562, 563, 564, 592,
594, 600, 601
Akai
513, 514, 515, 516, 517,
518, 519, 520, 568,
Kenwood
562, 581, 592, 594, 600,
601
Alba
546
Lloyd
588
Amstrad
588
Logik
589
Luxor
518
ASA
28
565
121716
text_dishpvr.fm Page 29 Friday, February 28, 2003 1:22 PM
VCR
CODES
VCR
CODES
Magnavox
527, 553, 554, 556, 565,
611
Sears
548, 549, 581, 584, 608,
610,
Marantz
530, 554, 565, 585, 592,
594, 600, 601, 603
Sentra
546
Sharp
585, 607, 609, 625
Shintom
589
533, 549, 554, 566, 581,
585, 588, 608
Sony
500, 501, 502, 503, 504
MGA
567, 568, 609
Sylvania
553, 554, 556, 567, 588,
611
Mitsubishi
562, 567, 568, 569, 570,
571, 609
Symphonic
588, 594
MTC
544, 580, 588
Tandy
588
Multitech
588, 589, 591
Tashiko
588
NAD
573
Tatung
586, 594, 601
NEC
530, 531, 532, 562, 592,
594, 599, 600, 601, 602,
603, 604
Teac
588, 594, 601
Technics
553, 554
Olympic
553
Teknika
554, 587, 588
Optonica
585
TMK
506
Orion
506, 507
Toshiba
534, 535, 567, 590
Panasonic
521, 522, 523, 524, 526,
553, 554, 598, 614, 628
Totevision
580, 591
Pentax
537, 592
Unitech
580
MEI
Memorex
Perdio
554
588
Philco
553, 554, 611
Philips
553, 554, 565, 585
Pioneer
553, 562, 573, 574, 575,
576, 600
Portland
546, 593
Proscan
Pulsar
Quartz
581
Quasar
553, 554, 577, 578
Radio Shack
607, 608, 609, 610
RCA
525, 526, 527, 528, 529,
537, 553, 591, 605, 606,
615, 630, 631
Vector Reaserch
530, 600
Victor
561, 562, 600
Video Concepts
568, 600
Videosonic
591
Wards
527, 554, 580, 585, 588,
589, 590, 591, 607, 608,
609
553, 605
Yamaha
530, 592, 594, 600, 601
533
Zenith
500, 501, 533
CABLE TV BOX CODES
Cable Boxes
Codes
Eastern
649
Realistic
549, 554, 580, 581, 584,
585, 588
CI/Tocom
640
Ricoh
502
Jerrold
635, 636
Saisho
506, 507
Memorex
637
Salora
567, 581
Oak
646
Samsung
517, 534, 579, 580, 591
Panasonic
637, 644, 645
Sansui
532, 544, 562, 600, 621
Paragon
637
Sanyo
549, 581, 582, 583, 608
Pioneer
642, 643
SBR
565
Regency
649
Schneider
589
Scientific America
638, 639. 647, 648, 650
Scott
508, 559, 590
Zenith
641
121716
29
text_dishpvr.fm Page 30 Friday, February 28, 2003 1:22 PM
DVD P LAYER CODES
DVD Players
Codes
Tuner/Amplifier
Codes
Onkyo
660, 662, 678, 689, 699,
700
Aiwa
634
Optimus
664, 697
Hitachi
632, 635
Panasonic
652, 707
JVC
636
Pioneer
658, 661, 667, 668, 675,
679, 688, 692, 702
Konka
637, 638
Proton
654, 705
Magnavox
626
Quasar
652, 707
RCA
655, 704, 729
Realistic
665, 666
Scott
659, 701
Sharp
712, 713, 714, 715
Sherwood
670, 695
Sony
673, 680, 687, 693, 730,
731
Mitsubishi
Panasonic
Philips
Pioneer
RCA
Sanyo
629
639
640, 641, 642
619
627
643
Sony
617, 644, 645
Toshiba
616, 646, 647
Symphonic
666
Zenith
648
Teac
684
Technics
652, 658, 707
Toshiba
710
Victor
657, 703
Yamaha
663, 682, 685, 698, 732,
733
Note: You must put the remote control
in VCR mode to set it up to control a DVD
player. Later, you must put the remote control
in VCR mode to use it to control a DVD player.
TUNER/AMPLIFIER CODES
Tuner/Amplifier
Codes
Aiwa
656, 680, 687, 718, 719,
720, 723, 724, 725, 726
Carver
653, 706
Citizen
709
Denon
674
Fisher
653, 706
GE
665, 711
Goldstar
677, 690
Harmon Kardon
672
Hitachi
717
JVC
657, 683, 703, 727
Kenwood
676, 691, 728
Luxman
681, 686
LXI
665
Magnavox
705
Marantz
708, 651
Memorex
675, 692
NAD
669, 696
Nakamichi
671, 694
NEC
716
30
121716
text_dishpvr.fm Page 31 Friday, February 28, 2003 1:22 PM
TROUBLESHOOT THE REMOTE CONTROL
What’s
Happening
What’s Wrong
While you do
a remote
procedure, the
remote control
“times out.”
• If you don’t press
any button
for 20 seconds in
a programming
sequence,
the remote
“times out.”
• If you hold a
button longer
than two
minutes, the
remote control
stops
transmitting to
save battery life.
Start over again.
When you
press the
remote control
Power button
to turn the
receiver on,
the receiver’s
front panel
Power light
doesn’t turn
on.
• Maybe the
batteries are
weak or dead.
• Maybe you didn’t
plug the receiver
power cord into a
power outlet, or
maybe there’s a
problem with the
power.
• Maybe the
remote isn’t in
SAT mode.
• Maybe the
remote and the
receiver have
different
addresses.
• Replace the remote batteries with
fresh ones.
121716
What You Can Do
• Make sure the receiver power cord
is plugged into a power outlet.
• Press SAT to set the remote to SAT
mode to control the receiver.
• Make sure the remote and the
receiver have the same address.
See Change the Address on
page 9.
31
text_dishpvr.fm Page 32 Friday, February 28, 2003 1:22 PM
What’s
Happening
What’s Wrong
What You Can Do
When you
press a button
on the remote
control, the
device doesn’t
do what you
expect.
• Maybe you’re
trying to control a
device and
you’re not
pointing the
remote control
right at it.
• Remember, the remote control uses
IR signals to control all devices
except for the receiver (when using
the UHF antenna). IR signals travel
only 40 feet or less, and can’t go
through walls or other solid objects.
You must point the remote control
right at the device, with no objects to
block the signal path.
• If the batteries are missing or dead,
put in fresh AAA-size batteries. If
the remote has fresh batteries,
check whether you put them in the
right way. If you didn’t, take them
out and put them in as described on
page 2.
• Maybe the
remote control is
missing
batteries, maybe
you put the
batteries in the
remote the
wrong way, or
maybe the
batteries are
weak or dead.
• Maybe you didn’t
set the remote to
the mode for the
device you want
to control.
• Maybe you didn’t
set up the remote
to control the
device.
• UHF signals from
a neighbor’s
remote may be
blocking signals
from your
remote.
When you
press the
remote control
Mute or
Volume
button,
nothing
happens.
32
• Maybe you have
not set up the
remote control.
• Maybe you’re
trying to control
TV volume but
you set up the
remote
to control a tuner
or amplifier in
AUX mode.
• Maybe you’re
trying to control
tuner or amplifier
volume but you
set up the remote
to control a TV
in AUX mode.
• Press the correct mode button to set
the remote to the mode for the
device you want
to control.
• Make sure you set up the remote
to control all the devices you want
to use. See Remote Control Setup
on page 6.
• Put a UHF attenuator on the
receiver’s UHF Remote Antenna
input. This will help keep stray
signals from blocking your remote’s
signals, but also cut down how far
away you can use the remote.
Change your receiver’s address
(see Change the Address on
page 9).
• See Remote Control Setup on
page 6.
• Set up the remote to control either
TV volume or tuner/amplifier
volume, whichever you want.
121716
text_dishpvr.fm Page 33 Friday, February 28, 2003 1:22 PM
LIMITED WARRANTY
This Limited Warranty is a legal document. Keep it in a
safe place. Remember to keep your Sales Receipt for
warranty service. We will consider
any items you return without a copy of the
Proof of Purchase to be out of warranty.
This warranty extends only to the original user of the DISH Network
remote control (“you,” “your”) and is limited to the purchase price of the remote
control. EchoStar Communications Corporation and its affiliated companies
(“we,” “our,” “us”) warrant this remote control against defects in materials or
workmanship as follows.
For one year from the original date of purchase, if we find the remote control is
defective subject to the limits of this warranty, we will replace the remote at no
charge for parts or labor. We warrant any such work done against defects in
materials or workmanship for the remaining part of the original warranty
period.
This warranty does not cover installation of the DISH Network System;
consumer instruction; physical set up or adjustment of any consumer electronic
device; remote control batteries; signal reception problems; loss of use of the
equipment; unused programming charges due to equipment malfunction;
cosmetic damage; damage due to lightning, electrical or telephone line surges,
fire, flood, or other acts of Nature; accident; misuse; abuse; repair or alteration
by other than our factory service; negligence; commercial or institutional use;
improper or neglected maintenance; equipment sold AS IS or WITH ALL
FAULTS; equipment removal or reinstallation; shipping damage if the
equipment was not packed and shipped in the manner we prescribe; nor
equipment purchased, serviced, or operated outside the contiguous
United States of America.
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR
EXCLUSIVE REMEDY. WE SHALL NOT BE HELD LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESSED OR IMPLIED WARRANTY ON THIS DEVICE, NOR FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE RESULTING FROM
THE USE OF, OR INABILITY TO USE, THIS DEVICE. UNDER NO
CIRCUMSTANCES SHALL OUR LIABILITY, IF ANY, EXCEED THE
PURCHASE PRICE PAID FOR THIS DEVICE. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON
THIS DEVICE IS LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. WE RESERVE THE RIGHT TO REFUSE TO HONOR THIS
WARRANTY IF WE DETERMINE ANY OF THE ABOVE EXCEPTIONS
TO HAVE CAUSED THIS DEVICE NOT TO HAVE PERFORMED
PROPERLY. THIS WARRANTY SHALL BE VOID IF ANY FACTORYAPPLIED IDENTIFICATION MARK, INCLUDING BUT NOT LIMITED TO
121716
33
text_dishpvr.fm Page 34 Friday, February 28, 2003 1:22 PM
SERIAL OR CONDITIONAL ACCESS NUMBERS, HAS BEEN ALTERED
OR REMOVED. THIS WARRANTY SHALL ALSO BE VOID IF THE
DEVICE HAS BEEN OPENED BY AN UNAUTHORIZED PERSON (with
the exception of opening the battery cover).
This warranty gives you specific legal rights which may vary from state to state.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, or allow limitations on the duration of an implied
warranty, so those limitations may not apply to you.
A DVANCE EXCHANGE PROGRAM
The Advance Exchange Program allows you to have replacement equipment
shipped immediately to you (depending upon where you live, it could take three
to five business days). Along with replacement equipment, you will receive a
prepaid shipping label and instructions on how to return the defective
equipment.
The shipping charge, for receiving replacement equipment and returning the
defective equipment, is a one time fee based on EchoStar's competitive bulk
shipping rates (additional charges may apply outside of the continental US).
This fee will be charged to your billing account or your valid credit card.
If you do not ship the defective equipment to EchoStar within ten days after
receiving the replacement, your billing account or credit card will be charged
the market price of the replacement. If you return the defective equipment after
ten days, you will receive a full refund less an administrative fee.
If your equipment is out of warranty and can be repaired your billing account or
credit card will be charged the standard repair fee for the replacement. If
damage to the defective equipment is found, which EchoStar in its sole
discretion determines has voided the warranty, or makes the equipment
unrepairable, your billing account or credit card will be charged the market
price of the replacement.
POST R ECEIPT E XCHANGE PROGRAM
You may choose to ship the equipment to us at your cost. To provide faster
service, upon receipt of your equipment you will be shipped a replacement.
Your original equipment will not be available for return.
The equipment you return will be checked to verify whether it is covered under
this warranty. If the defective equipment is covered under this warranty, it will
be replaced and shipped back to you at no additional cost (additional charges
may apply outside of the continental US).
If your equipment is out of warranty and can be repaired your billing account or
credit card will be charged the standard repair fee for the replacement. If
damage to the defective equipment is found, which EchoStar in its sole
discretion determines has voided the warranty, or makes the equipment
unrepairable, your billing account or credit card will be charged the market
price of the replacement.
34
121716
text_dishpvr.fm Page 35 Friday, February 28, 2003 1:22 PM
A CCESSORY WARRANTY
An accessory is any DISH Network branded equipment, displaying the DISH
Network logo, excluding the receiver, Smart Card, cables and hookups, and
non-mechanical components. A one-year warranty becomes effective upon the
activation of the DISH system or date of purchase, if bought separately. A proof
of purchase is required to verify the purchase date. If an accessory has an
expired warranty, no exchange will be issued. You may purchase replacement
accessories from DISH Network or your local retailer.
IF YOU NEED HELP
1. Review this User Guide.
2. See Troubleshoot the Remote starting on page 31.
3. Call the Customer Service Center at 1-800-333-DISH (3474).
Have the date of purchase and your customer account number
ready.
4. A Representative will help you.
5. If the Representative finds you should return the remote control,
you’ll get a telephone number to call for a Return Authorization
(RA) number. Before shipping any equipment to us, you must
get a Return Authorization number.
6. You must package returned equipment the right way. Follow the
instructions the Representative gives you.
7. Write the RA number in large, clearly visible characters on the
outside of the shipping box used to return the equipment.
To avoid confusion and misunderstandings, we will return
shipments without an RA number clearly visible on the outside
of the box to you at your cost.
8. We will:
• Check the remote control, including whether it is covered
under the warranty.
• Replace any remote we find is defective with a new or
refurbished remote, if the defective remote is covered under
the warranty. We will ship the replacement remote at our
expense.
• If a defective remote is not covered under the warranty,
we will tell you. We may assess you a flat rate charge for a
replacement remote, including shipping and insurance.
121716
35
text_dishpvr.fm Page 36 Friday, February 28, 2003 1:22 PM
INDEX
A
Address, Change the 9
Amplifier Codes 30
Amplifier, Control an 24
Antenna, Remote Control, Attach the
3
Attenuator, Install an 4
B
Batteries, Remote Control 2
Buttons, Remote Control 11
C
Cable TV Box Codes 29
Cable TV Box, Control a 22
Change the Address 9
Check the Device Codes 8
Customer Service 35
D
Device Codes 26
Amplifier Codes 30
Cable TV Box Codes 29
Tuner and Amplifier Codes 30
Tuner Codes 30
TV Codes 26
VCR Codes 28
Device Codes, Check the 8
Device Codes, Scan for 7
DishPVR 2
DishPVR Buttons 14
DVD Player, Control a 20
Remote Control Signals - UHF
and IR 3
Remote Control Batteries 2
Remote Control Buttons 11
Amplifier, Control an 24
Cable TV Box, Control a 22
DishPVR Buttons 14
DVD Player, Control a 20
Receiver, Control the 11
Second TV, Control a 17
Second VCR, Control a 20
Tuner or Amplifier, Control a
24
TV, Control a 17
VCR, Control a 20
Remote Control Modes 5
Remote Control Setup 6
Change the Address 9
Check the Device Codes 8
Install an Attenuator 4
Scan for Device Codes 7
Set Up the Remote Control 6
TV and Device Volume Control
10
S
Scan for Device Codes 7
Second TV, Control a 17
Second VCR, Control a 20
Set Up the Remote Control 6
Setup, Remote Control 6
Switch Between TV and Device Volume Control 10
I
T
If You Need Help 35
Install an Attenuator 4
IR Signals, Remote Control 3
Troubleshoot the Remote Control 31
Tuner Codes 30
Tuner or Amplifier, Control a 24
TV Codes 26
TV, Control a 17
M
Modes, Remote Control 5
U
R
UHF Signals, Remote Control 3
Receiver, Control the 11
Remote Control Basics 2
DishPVR 2
Remote Control Batteries 2
Remote Control Modes 5
V
36
VCR Codes 28
VCR, Control a 20
Volume Control, Switch Between TV
and Device 10
121716
inside_back_cover_dishpvr.fm Page 0 Thursday, February 27, 2003 1:49 PM
Copyright © 2003
EchoStar Technologies Corporation
Englewood, Colorado 80112
All rights reserved.
The information in this Guide may change without notice.
We may issue revisions to tell you about such changes.
Send any comments or questions to:
EchoStar Technologies Corporation,
Technical Publications, 94 Inverness Terrace East,
Englewood, Colorado 80112
Part Number: 121716
Printed in the United States of America.
DISH Network is a registered trademark of EchoStar Technologies
Corporation. For information about DISH Network, visit our website
at www.dishnetwork.com.