User`s guide | Disney DCR5500-C Clock Radio User Manual

QUICK REFERENCE
The Quick Reference is given to provide basic operation of the unit.
Please completely read the user’s guide to take advantage of all the
features this unit has to offer.
Slide to select the alarm (AUTO: Radio
or BUZZ: Buzzer) or to turn the
unit ON or OFF
Press to temporarily turn off the alarm
for 7 minutes and turn on the
backlight for 5 seconds
Slide to select AM or FM
Minute/Hour/Second/Alarm hands
Rotate to set the radio station
AM Dial Scale Pointer and Backlight
FM Dial Scale Pointer and Backlight
Battery Compartment
Insert three (3) "AA" batteries to operate
the clock, radio and alarm
Rotate to adjust the volume
Gently pull out and rotate to
adjust the time. Rotate to
adjust the alarm time.
DC IN 4.5V Jack (Center Positive)
Fully extend for best FM reception
Disney Elements © Disney
1
QUICK REFERENCE (CONTINUED)
TO LISTEN TO THE RADIO:
1. Slide the AUTO/BUZZ/ON/OFF switch to the ON position to turn the unit on.
2. Slide the Band switch to the desired band, AM or FM.
3. Tune a station by rotating the TUNING ring.
4. Adjust the volume using the Volume control.
5. Slide the AUTO/BUZZ/ON/OFF switch to the OFF position to turn the unit off.
TO SET OR RESET THE ACTUAL TIME:
Gently pull out and then rotate the Clock/Alarm Time Set knob on the rear of the unit until
the current time appears on the front clock.
TO SET OR RESET THE ALARM TIME:
Rotate the Clock/Alarm Time Set knob on the rear of the unit until the Alarm hand points
at the desired alarm hour.
TO SET THE ALARM TO WAKE TO RADIO:
1. Set the alarm time as instructed above. Select a radio station and make sure the
Volume control is set as desired.
2. Slide the AUTO/BUZZ/ON/OFF switch to the AUTO position. When the actual time
matches the selected preset alarm time, the radio will automatically turn on.
3. To shut the alarm off, slide the AUTO/BUZZ/ON/OFF switch to the OFF position. Slide
the AUTO/BUZZ/ON/OFF switch to the AUTO position to reset it for the next day.
TO SET THE ALARM TO WAKE TO BUZZER:
1. Set the alarm time as instructed above. Make sure the Volume control is set as
desired.
2. Slide the AUTO/BUZZ/ON/OFF switch to the BUZZ position. When the actual time
matches the selected preset alarm time, the buzzer will automatically turn on.
3. To shut the alarm off, slide the AUTO/BUZZ/ON/OFF switch to the OFF position. Slide
the AUTO/BUZZ/ON/OFF switch to the BUZZ position to reset it for the next day.
NOTE:
When setting the alarm, please make sure the volume is not at minimum. Otherwise,
there will be no sound when alarming.
BACKLIGHT
Press the SNOOZE button, the backlight will turn on for 5 seconds.
SNOOZE:
The alarm can be temporarily turned off manually by pressing the SNOOZE button; the
alarm will turn back on automatically 7 minutes later.
Disney Elements © Disney
2
SAFETY PRECAUTIONS
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
• Place the unit on a stable surface.
• Avoid installing the unit in locations described below:
• Places exposed to direct sunlight or close to heat radiating
appliances such as electric heaters.
• On top of other stereo equipment that radiates too much heat.
• Places lacking ventilation or dusty places.
• Places subject to constant vibration.
• Humid or moist places.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning
and power surges ARE NOT covered under warranty for this product.
3
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all
operating instructions carefully. Please note
that these are general precautions and may
not pertain to your unit. For example, this unit
may not have the capability to be connected
to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions
should be read before the product is
operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should
be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be
followed.
5. CLEANING
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a dry cloth for
cleaning.
6. ATTACHMENTS
Do not use attachments not recommended
by the product's manufacturer as they may
cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for
example: near a bathtub, washbowl, kitchen
sink or laundry tub; in a wet basement; or
near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable
cart, stand, tripod, bracket or table. The
product may fall, causing serious injury and
serious damage to the product. Use only
with a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold
with the product. Any mounting of the
product should follow the manufacturer’s
instructions, and should use a mounting
accessory recommended by the
manufacturer.
8A. An appliance and cart combination should
be moved with care. Quick
stops, excessive force and
uneven surfaces may cause
the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the
back or bottom are provided for ventilation,
to ensure reliable operation of the product
and to protect it from overheating. These
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug or
other similar surface. This product should
never be placed near or over a radiator or
heat source. This product should not be
placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions
have been adhered to.
10. POWER SOURCES
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your home, consult your
appliance dealer or local power company.
For products intended to operate from
battery power, or other sources, refer to the
operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized
alternating-current line plug (a plug having
one blade wider than the other). This plug
will fit into the power outlet only one way.
This is a safety feature. If you are unable to
insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords at
plugs, convenience receptacles, and the
PORTABLE CART WARNING
(symbol provided by RETAC)
4
IMPORTANT SAFETY INSTRUCTIONS
13.
14.
15.
16.
17.
18.
19.
point where they exit from the appliance.
LIGHTNING
To protect your product from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug it
from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and
power-line surges.
POWER LINES
An outside antenna system should not be
located in the vicinity of overhead power
lines or other electric light or power circuits,
or where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to
keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.
OBJECT AND LIQUID ENTRY
Never push objects of any kind into this
product through openings as they may
touch dangerous voltage points or short out
parts that could result in fire or electric
shock. Never spill or spray any type of liquid
on the product.
SERVICING
Do not attempt to service this product
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified
service personnel.
REPLACEMENT PARTS
When replacement parts are required, be
sure the service technician uses
replacement parts specified by the
manufacturer or those that have the same
characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
SAFETY CHECK
Upon completion of any service or repairs to
this product, ask the service technician to
20.
21.
a.
b.
c.
d.
e.
f.
22.
23.
24.
5
perform safety checks to determine that the
product is in proper operating condition.
WALL OR CEILING MOUNTING
The product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
When the power-supply cord or plug is
damaged.
If liquid has been spilled or objects have
fallen into the product.
If the product has been exposed to rain or
water.
If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions, as an adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the product to its
normal operation.
If the product has been dropped or the
cabinet has been damaged.
When the product exhibits a distinct change
in performance–this indicates a need for
service.
HEAT
The product should be situated away from
heat sources such as radiators, heat
registers, stoves or other products (including
amplifiers) that produce heat.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV
system installer's attention to Article 820-40
of the NEC that provides guidelines for
proper grounding and, in particular, specifies
that the cable ground shall be connected to
the grounding system of the building, as
close to the point of cable entry as practical.
NONUSE PERIODS
The power cord of the appliance should be
unplugged from the outlet when left unused
for a long period of time.
LOCATION OF CONTROLS
FRONT
1. Left Speaker
1
2
3
4
5
6
7
8
9
10
11
12
13
REAR
2. Right Speaker
3. AUTO/BUZZ/
ON/OFF Switch
4. SNOOZE Button
5. Band (FM/AM)
Switch
6. Minute Hand
7. Hour Hand
8. Second Hand
9. Alarm Hand
10. AM Dial Scale
Pointer and
Backlight
11. TUNING Ring
14
12. FM Dial Scale
Pointer and
Backlight
13. Battery
Compartment
(Bottom of Unit)
14. VOLUME Control
15
15. Clock/Alarm
Time Set Knob
16
16. DC IN Jack 4.5V
z
17. FM Antenna Wire
17
6
POWER SOURCES
CLOCK OPERATION
To operate the clock, one (1) AA battery must be installed as follows:
1. Remove
the
battery
compartment door on the
bottom of the unit by inserting a
small screwdriver, paper clip or
similar item into the tab while
gently pushing, then lifting it out.
2. Insert one (1) AA battery (not
included) as shown at the right
and according to the polarity
diagram. Alkaline batteries are
recommended for longer
playing time.
ALARM AND RADIO OPERATION
The alarm and radio can be powered by either two (2) AA batteries or an
AC adapter (not included).
BATTERY OPERATION
1. Remove the battery compartment door on the bottom of the unit by
inserting a small screwdriver, paper clip or similar item into the tab
while gently pushing, then lifting
it out.
2
2. Insert two (2) AA batteries (not
included) as shown at the right
and according to the polarity
diagram. First insert the battery
labeled “1”, and then the battery
1
labeled “2”. Alkaline batteries
are recommended for longer
playing time.
7
POWER SOURCES (CONTINUED)
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated next to
the battery compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and
Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat
and rupture. (Follow battery manufacturer’s directions.)
AC Operation
To operate the unit using AC power, connect a 4.5V DC, 600mA AC
adapter with positive center (included) to the DC jack on the rear of the
unit and then to a wall outlet having 120V, 60Hz AC only.
DC 4.5V Z
NOTES:
• The batteries that operate the radio and the alarm are automatically
disconnected when the AC adapter is used.
• The AC adapter will NOT operate the time, you must install the
battery as described on the previous page.
8
OPERATION
TO LISTEN TO THE RADIO
1
2
2
1
Slide the AUTO/BUZZ/ON/OFF
switch 1 to the ON position to turn
the unit on. Slide the Band switch 2
to the desired band, AM or FM.
Tune a station by rotating the
TUNING ring.
3
Antennas
FM: Extend the FM antenna wire
(located
in
the
battery
compartment) for best reception.
AM: Turn the unit for better AM
reception.
1
2
Adjust the volume using the Volume
control ❶. Slide the AUTO/BUZZ/
ON/OFF switch 2 to the OFF
position to turn the unit off.
BACKLIGHT
1
Press the SNOOZE button, the
backlight at the AM and FM Dial
Scale Pointer will light on for 5
seconds. This is useful for
observing the time and the Radio
frequency when using the unit at
night.
9
OPERATION (CONTINUED)
TO SET OR RESET THE ACTUAL TIME
1
2
Gently pull out the Clock/Alarm
Time Set knob on the rear of the
unit.
Rotate the Clock/Alarm Time Set
knob on the rear of the unit until the
current time appears on the front
clock. Then gently push in the
Clock/Alarm
1 Time Set knob to
replace the knob.
TO SET OR RESET THE ALARM TIME
1
Rotate the Clock/Alarm Time Set
knob on the rear of the unit until the
Alarm hand points at the desired
alarm hour.
1
10
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO RADIO
1
2
Set the alarm time as previously
instructed. Select a radio station as
described on page 9 and make sure
the Volume control is set as desired.
NOTE: Make sure the volume is not
at minimum, 1
otherwise, there will be
no sound when alarming.
Slide the AUTO/BUZZ/ON/OFF
switch to the AUTO position. When
the actual time matches the
selected preset alarm time, the
radio will automatically turn on.
3
To shut the alarm off, slide the
AUTO/BUZZ/ON/OFF switch to the
OFF
position.
Slide
the
AUTO/BUZZ/ON/OFF switch to the
AUTO position to reset it for the
next day. See page 13 for the
Snooze feature.
11
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO BUZZER
1
2
Set the alarm time as previously
instructed. Make sure the Volume
control is set as desired.
NOTE: Make sure the volume is not
at minimum, otherwise, there will be
1 alarming.
no sound when
Slide the AUTO/BUZZ/ON/OFF
switch to the BUZZ position. When
the actual time matches the
selected preset alarm time, the
disney alarm will automatically turn
on.
3
To shut the alarm off, slide the
AUTO/BUZZ/ON/OFF switch to the
OFF
position.
Slide
the
AUTO/BUZZ/ON/OFF switch to the
BUZZ position to reset it for the next
day. See page 13 for the Snooze
feature.
12
OPERATION (CONTINUED)
TO SHUT THE ALARM OFF
SNOOZE
1
1
To shut the alarm off, slide the
AUTO/BUZZ/ON/OFF switch to the
OFF
position.
Slide
the
AUTO/BUZZ/ON/OFF switch to the
AUTO or BUZZ position to reset it
for the next day.
The alarm can be temporarily turned
off manually by pressing the SNOOZE
button; the alarm will turn back on
automatically 7 minutes later.
NOTE: When the SNOOZE button is
pressed, the AM/FM Dial Scale Pointer
and Backlight will light for 5 seconds.
13
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service:
SYMPTOM
POSSIBLE
CAUSE
POSSIBLE
SOLUTION
AUTO/BUZZ/ON/OFF
Set AUTO/BUZZ/ON/OFF
RADIO/ALARM
No sound.
switch not set to ON.
switch to ON.
Volume control at
Increase the volume.
minimum position.
Noise or sound
AM–Interference from
Turn the radio for
distorted on AM
traffic.
better AM reception.
or FM.
FM–Antenna Wire
Extend Antenna Wire.
not extended.
Batteries dead or weak. Replace batteries;
see page 7.
AC adapter not
Check connection.
connected properly.
CLOCK
Clock does not
Battery not inserted.
operate.
Insert battery for clock
to operate; see page 7.
Alarm does not
AUTO/BUZZ/ON/OFF
turn on.
switch not set to AUTO switch to the AUTO or
Set AUTO/BUZZ/ON/OFF
or BUZZ.
BUZZ position as desired.
Volume is set to
Make sure the volume is
minimum.
not set to minimum.
14
For additional set-up or operating assistance,
please visit our website at www.disneyelectronics.com
or contact customer service at (954) 660-7026.
Please keep all packaging material for at least 90 days in case you
need to return this product to your place of purchase or Memcorp.
For parts and accessories, contact Fox International at 1-800-321-6993.
Distributed by Memcorp Inc., Weston, FL, Disney Elements © Disney 2004.
Para informacion adicional sobre la configuracion o si necesita asistencia con
la operacion del equipo, por favor visitenos en nuestra pagina web
www.disneyelectronics.com o si requiere asistencia directa, comuniquese con
nuestro departamento de servicio al cliente al numero (954) 660-7026.
Por favor mantenga todo el material de empaque por lo menos por 90 dias,
en caso que usted necesite devolver el producto donde lo compro a
directamente a Memcorp Inc.
Para Accesorios o Partes en general, por favor comuniquese con Fox
International al numero 1-800-321-6993.
Distribuido por Memcorp inc. Weston, FL, Disney Elements@Disney 2004.
Pour obtenir des informations supplémentaires sur l’installation ou une
assistance concernant l’emploi de votre produit, veuillez visiter notre site
Web sur www.disneyelectronics.com ou contacter notre service clientèle au
(954) 660-7026.
Veuillez conserver tout matériel d’emballage pendant au moins 90 jours
au cas où vous devriez renvoyer votre produit à votre revendeur ou
directement à Memorex.
Pour les pieces et les accessoires, contactez Fox International at au
1-800-321-6993
Distribué par Memcorp. inc . Weston, FL, Disney Elements@Disney 2004.
Download PDF

advertising