Operator`s manual | Dixon 17823-106 Lawn Mower User Manual

Zeeter Series
ZTR®
Model Year 2004
IMPORTANT - READ CAREFULLY
The Dixon® ZEETER® Mower is both easy and fun
to operate. However, any power mower must be
operated properly to be safe. It is not a toy or a
recreational vehicle. Before you start to use the
mower, read the operator’s manual carefully and
become completely familiar with the controls.
The information contained in this manual applies to
all Dixon® ZEETER® Mowers. Your Dixon dealer
will gladly answer any questions.
See your dealer for warranty service, parts and
repairs.
INDEX
Page
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . .13
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 14-16
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
Operation Instructions. . . . . . . . . . . . . . . . . . . 20-27
Care & Maintenance. . . . . . . . . . . . . . . . . . . . . .28-42
Standard Service Parts List. . . . . . . . . . . . . . . . . . . .43
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . .44-45
ZEETER ® Series
Part No. 14251-0703
3
SAFETY
RIDING LAWN MOWERS,
IF IMPROPERLY OPERATED,
CAN CAUSE SERIOUS INJURY OR DEATH.
The most common causes of injury to the operator or bystander...
BLADE CONTACT
TIP OVER
RUN OVER
BACK OVER
...read and understand this manual to prevent injuries.
4
SAFETY
Safety Alert Symbol
When you see this symbol,
BE ALERT to the potential for injury.
Follow recommended safety precautions
and safe operating practices.
DANGER
(highlighted in red)
indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING
(highlighted in orange)
indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION
(highlighted in yellow)
indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury. It may also be used
to alert against unsafe practices.
5
SAFETY
Failure to observe the following safety
instructions could result in serious injury or death.
GENERAL OPERATION:
•Read, understand, and follow all instructions in the
manual and on the mower before starting.
•Only allow responsible adults, who are familiar with the
instructions, to operate the mower.
•Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
•Be sure the area is clear of other people before mowing.
Stop mower if anyone enters the area.
•NEVER carry passengers.
•Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
•Be aware of the mower discharge direction and do not
point it at anyone.
•Do not operate the mower without either the entire
grass catcher or the deflector in place.
•Slow down before turning.
•Never leave a running mower unattended. Always turn off
blades, set parking brake, stop engine and remove key
before dismounting.
6
SAFETY
GENERAL OPERATION (continued):
•Turn off blades when not mowing.
•Stop engine before removing grass catcher or unclogging
chute.
•Mow only in daylight or good artificial light.
•Do not operate the mower while under the influence of
alcohol or drugs.
•Watch for traffic when operating near or crossing
roadways.
•Use extra care when loading or unloading the mower into
a trailer or truck. Do not ride the mower when loading
and unloading.
•Always wear safety goggles or safety glasses with side
shields when operating mower.
•Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability to
operate the riding mower safely enough to protect themselves and others from serious injury.
•Follow the manufacturer’s recommendation for wheel
weights and counterweights.
•Maintain or replace safety & instruction labels as needed.
WARNING:
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
7
SAFETY
SLOPE OPERATION:
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result
in severe injury or death.
All slopes require extra caution.
If you cannot back up the slope or if you feel
uneasy on it, do not mow it!
DO
•Mow across the slope with your Dixon ZTR - never up or
down.
•Remove obstacles such as rocks, tree limbs, etc.
•Watch for holes, ruts or bumps. Uneven terrain could
overturn the mower. Tall grass can hide obstacles.
•Use slow speed. Tires may lose traction on slopes even
though the brakes are functioning properly.
•Use extra care with grass catchers or other attachments. These can change the stability of the mower.
•Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction.
8
SAFETY
SLOPE OPERATION (continued):
DO (continued)
•Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly down the slope.
•If front wheels lift off the ground, pull the levers back to
stabilize the mower.
DO NOT
•Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
•Do not mow near drop-offs, ditches, or embankmnets.
The mower could suddently turn over if a wheel is over
the edge of a cliff or ditch or if an edge caves in.
•Do not mow on wet grass. Reduced traction could cause
sliding.
•Do not try to stabilize the mower by putting your foot on
the ground.
•Do not use grass catcher on steep slopes.
9
SAFETY
CHILDREN:
Tragic accidents can occur if the operator is
not alert to the presence of children.
Children are attracted to lawn mowers
and the mowing activity.
NEVER assume children will stay where they
were last seen.
Be alert to avoid accidents.
•Keep children out of the mowing area and under the
watchful care of another responsible adult.
•Be alert and turn mower off if a child enters the area.
•Before and during backing, look BEHIND and DOWN for
small children.
•Never carry children. They may fall off and be seriously
injured or interfere with safe mower operation.
•Never allow children to operate the mower.
•Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
10
SAFETY
SERVICE:
•Use extra care in handling gasoline and other fuels. They are
flammable and vapors are explosive.
Use only an approved container.
Never remove fuel cap or add fuel with engine running.
Allow engine to cool before refueling.
Do not smoke while refueling.
Never refuel the mower indoors.
Never store the mower or fuel container inside a building
where there is an open flame.
If fuel is spilled on clothing, change clothing immediately.
To prevent fire and explosion caused by static electricity:
Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before
filling.
When practical, remove fuel-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
fuel dispenser nozzle.
If a fuel dispenser nozzle must be used, keep the
nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
11
SAFETY
SERVICE (continued):
•Never run a mower inside a closed area. The exhaust
fumes are toxic.
•Keep nuts and bolts tight, especially blade attachment
bolts, and keep equipment in good condition.
•Never tamper with safety devices. Check their proper
operation regularly.
•Keep mower free of grass, leaves, or other debris buildup.
Clean up oil or fuel spillage. Allow mower to cool before
storing.
•Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
•Never make adjustments or repairs with the engine
running unless otherwise specified.
•Grass catcher components are subject to wear, damage
and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check components.
Replace with original equipment parts, when necessary.
•Mower blades are sharp and can cut. Wrap blade(s) or
wear gloves, and use extra caution when servicing them.
•Batteries contain sulfuric acid. To prevent burns avoid
contact with skin, eyes and clothing. To prevent a fire or
explosion keep sparks and open flames away from battery.
•Before disconnecting the negative (-) ground cable, make
sure all switches are OFF.
12
13
SPECIFICATIONS
ZEETER 30”
CHASSIS:
11 gauge welded channel frame
BODY:
All body parts made of rotational molded polyethylene.
Front body contains access panel for battery service.
Seat tilts forward to allow transmission service.
MOWER DECK:
11 GA stamped steel construction. Single 30” cut blade.
Cut height approximately 1-1/2”- 4” via 7-position lift handle.
BLADE DRIVE:
Mechanical; hand lever engagement
TRANSMISSION:
Each rear wheel is independently driven by chain and
sprockets through a friction mechanical drive.
ENGINE:
9 HP Briggs & Stratton Powerbuilt, 4-cycle, single
cylinder, air-cooled, gasoline, vertical shaft, aluminum
head and block.
STARTING SYSTEM: Electric by key switch operation with safety interlocks on
parking brake and blade drive.
TIRES:
Front
Rear
9 x 3.50-4 Turf Saver
16 x 6.50-8 Turf Saver
RECOMMENDED
TIRE PRESSURE:
Front
Rear
16-21 PSI
8-14 PSI
CAPACITIES:
Fuel
Engine
3 quart
1.25 quarts oil
DIMENSIONS:
Width
Width
Height
Length
Weight
32” outside rear wheel measurement
38” overall width of deck with deflector
31” to top edge of seat
65.5” hitch tab to front
390 lbs.
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
14
SPECIFICATIONS
ZEETER 36”
CHASSIS:
11 gauge welded channel frame
BODY:
All body parts made of rotational molded polyethylene.
Front body contains access panel for battery service.
Seat tilts forward to allow transmission service.
MOWER DECK:
11 GA laser cut fabricated. 36” cut width. Cut height
approximately 1-1/2”- 4” via 7-position lift handle.
BLADE DRIVE:
Electric clutch
TRANSMISSION:
Each rear wheel is independently driven by chain and
sprockets through a friction mechanical drive.
ENGINE:
11 HP Briggs & Stratton Powerbuilt, 4-cycle, single
cylinder, air-cooled, gasoline, vertical shaft, aluminum
head and block.
STARTING SYSTEM: Electric by key switch operation with safety interlocks
on parking brake and blade drive.
TIRES:
Front
Rear
9 x 3.50-4 Turf Saver
16 x 6.50-8 Turf Saver
RECOMMENDED
TIRE PRESSURE:
Front
Rear
16-21 PSI
8-14 PSI
CAPACITIES:
Fuel
Engine
3 quart
1.25 quarts oil
DIMENSIONS:
Width
Width
Height
Length
Weight
35” outside rear wheel measurement
50.5” overall width of deck with deflector
31” to top edge of seat
65.5” hitch tab to front
427 lbs.
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
15
SPECIFICATIONS
ZEETER 42”
CHASSIS:
11 gauge welded channel frame
BODY:
All body parts made of rotational molded polyethylene. Front
body contains access panel for battery service. Seat tilts
forward to allow transmission service.
MOWER DECK:
13 GA stamped steel construction. Three blades
combine for a 42” cut width. Cut height approximately
1-1/2” - 4” via 7-position lift handle.
BLADE DRIVE:
Electric clutch
TRANSMISSION:
Each rear wheel is independently driven by chain and
sprockets through a friction mechanical drive.
ENGINE:
13 HP Briggs & Stratton Powerbuilt, 4-cycle, single
cylinder, air-cooled, gasoline, vertical shaft, aluminum
head and block.
STARTING SYSTEM: Electric by key switch operation with safety interlocks
on parking brake and blade drive.
TIRES:
Front
Rear
9 x 3.50-4 Turf Saver
16 x 6.50-8 Turf Saver
RECOMMENDED
TIRE PRESSURE:
Front
Rear
16-21 PSI
8-14 PSI
CAPACITIES:
Fuel
Engine
3 quart
1.25 quarts oil
DIMENSIONS:
Width
Width
Height
Length
Weight
35” outside rear wheel measurement
55” overall width of deck with deflector
31” to top edge of seat
65.5” hitch tab to front
427 lbs.
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
16
CONTROLS
CONTROL LEVERS
TO GO FORWARD:
•From neutral position, gently push both control levers forward.
•To increase speed, move levers further forward.
TO GO BACKWARD:
•From neutral position, gently pull both control levers toward you.
TURNING:
•Turning is controlled by moving one control lever slightly forward or
rearward of the other.
•To turn left, move left lever rearward of the right lever.
•To turn right, move right lever rearward of the left lever.
•To turn on mower’s own axis (zero turning radius), stop and move one
lever to reverse position and the other to forward position.
BRAKING:
•To brake mower, move both levers in direction opposite of travel.
Note: The pressure required to operate the mower is very light.
17
CONTROLS
The Dixon ZEETER has a unique transaxle that requires only two drive
levers to control braking, turning, speed and direction.
On initial operation, set throttle speed on slow. Operate with mower
blade in “OFF” position.
To avoid “over-controlling” the mower, use a light touch on the drive
levers.
Slight movements using fingertip control is all that is necessary.
PARKING BRAKE:
The parking brake is designed to hold the mower
from moving and is not intended for use in stopping
the mower while it is in motion.
Engage parking brake before
C A U T I O N starting engine.
TO SET PARKING BRAKE:
The hand operated parking brake is located on the
right side of the mower.
To engage brake, pull lever up (to the rear).
To release brake, move lever forward (down).
NOTE:
18
Always set parking brake before
dismounting. Release parking brake
before moving mower.
CONTROLS
TRANSMISSION DRIVE SYSTEM
Allows the mower to turn on its own axis “ZERO TURNING RADIUS”.
Each lever controls one side of the mower.
NOTE: The pressure required to operate the mower is very light.
BLADE DRIVE (30”):
•Located to left of the operator.
•To engage the mower blade, turn lever on floor
slowly to the “ON” position.
•To disengage mower blade, turn lever to the
“OFF” position.
30”
BLADE DRIVE (36” & 42”):
•Located on the control panel, operator’s right.
•To engage the mower blades, pull up on the switch.
•To disengage mower blades, push down.
THROTTLE CONTROL LEVER:
•Located on control panel to operator’s right.
•Throttle control for engine speed.
•Choke for engine starting.
•Throttle control should be set to MAXIMUM or wide
open setting to ensure adequate cooling of the engine
and to maintain mower deck blade speed while
mowing.
36” & 42”
MOWER DECK CUT HEIGHT LIFT LEVER:
•Located to the left of the operator.
•Controls the cutting height.
•Seven positions of adjustment.
•Move lever in and forward to lower.
•Move lever in and back to raise.
NOTE: Always use high for transport.
30”
19
OPERATION INSTRUCTIONS
The safe and successful operation of the ZEETER Mower
will depend upon the operator having the correct
knowledge of all controls used on the mower and making
good judgements about the terrain to be mowed.
NEVER allow anyone to operate the mower without
complete knowledge of all controls and their functions.
During initial operation, “learning to drive”, set throttle at
slow speed.
Sound judgement by the operator will prevent accidents.
TOWING:
Towing a trailer or other attachment that is too heavy could
damage the drive or cause the mower to become unstable.
Limit loads to 250 pounds or less with this mower.
20
OPERATION INSTRUCTIONS
BEFORE OPERATING MOWER:
1.
Read and observe all safety instructions on your mower
and in the manual.
2.
Read engine manufacturer’s operating and maintenance
instructions.
3.
Check engine oil.
4.
Check fuel cap to be sure it is in place.
5.
Be sure parking brake is on.
6.
Mower blade drive is off.
7.
Know how to stop engine. (Turn key to off position).
21
OPERATION INSTRUCTIONS
STARTING INSTRUCTIONS:
1.
Parking brake must be on, and blade drive disengaged.
2.
Move throttle control to “choke” position if engine is cold,
full throttle if warm.
3.
Insert ignition key and turn to “start” position. When
engine starts, release ignition key. Key will return to “run”
position.
4.
Move throttle from “choke” to desired speed position.
5.
Release parking brake.
6.
Operate the mower per the “CONTROL” instructions on
Page 17.
CAUTION
Do not operate the engine
in an enclosed area due to
the harmful exhaust gas
produced.
NOTE: When mowing, “blade(s) engaged”, throttle control
must be set to the MAXIMUM or wide open setting
to insure adequate cooling of the engine and to
maintain mower deck blade speed.
22
OPERATION INSTRUCTIONS
TESTING OF SAFETY INTERLOCK SYSTEMS:
Do not operate mower if safety switches are not
operating properly.
PARKING BRAKE SWITCH TEST:
a) Place parking brake in OFF position.
b) Turn ignition switch to START.
ENGINE SHOULD NOT TURN OVER
OR ATTEMPT TO START!
BLADE DRIVE SWITCH TEST:
a) Place parking brake in ON position.
b) Engage blade drive switch.
c) Turn ignition switch to START.
ENGINE SHOULD NOT TURN OVER
OR ATTEMPT TO START!
SEAT SWITCH TEST:
a) In a SAFE AREA away from bystanders, start the
engine.
b) Engage blade drive switch.
c) Raise slightly off seat.
ENGINE SHOULD STOP!
If any safety check fails: Do not operate the mower
until the system has been checked and repaired
by an authorized Dixon ZTR dealer!
23
OPERATION INSTRUCTIONS
SIDE DISCHARGE OF THE CLIPPINGS:
In order to achieve optimum performance when side
discharging the grass clippings, please read and follow
the tips listed below.
Additional information can be found in the troubleshooting
guide.
CAUTION
Be sure that the deflector is properly
installed on the discharge chute.
1. Set engine speed control to the wide open or full
setting.
2. Do Not Attempt To Cut Grass When It Is Wet. Wet
grass will clog the underside of the deck and discharge
area.
3. If the grass is tall, place the mower deck cut height
lever in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each pass.
Some applications may require a second cutting.
4. Keep The Underside Of The Mower Deck Clean.
Frequent removal of dried grass and dirt will allow the
clippings to discharge correctly.
5. Maintain Sharp Blade(s) Throughout The Cutting
Season.
24
OPERATION INSTRUCTIONS
GRASS HEIGHT AND CUTTING SUGGESTIONS:
Do not attempt to cut grass when it is wet.
If the grass is tall, place the mower deck cut height lever
in the top or second notch. “Initially” overlap cutting
swaths instead of a full swath with each pass. Some
applications may require a second cutting.
Keep the underside of the mower deck clean.
Maintain sharp blades throughout the cutting season.
As a rule of thumb, never cut off more than 1/3 of the
total grass blade length.
Correct mowing height can reduce weeds and disease by
50% to 80%.
The following grass cut heights are based an adequate
moisture conditions and normal thatch buildup in a healthy
lawn. Some locations and applications may require slightly
different cut heights. If in doubt, consult your local lawn
professional for assistance.
Grass Types
Bermudagrass
Bluegrass
Buffalograss
Ryegrass
Tall Fescue
Zoysiagrass
Best Cut Heights
1 - 2”
2 - 3”
11/2 -3”
2 - 3”
3-31/2”
1 - 3”
25
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT:
Mulching or recycling the grass clippings requires a
totally different mowing approach than would be normal
when side discharging or bagging the grass. There may
be instances or conditions where it is not possible to hide
all of the recycled or mulched clippings.
In order to achieve the best results, please read and
follow the mulching tips listed below:
1. Set the engine speed control to the wide open or full
setting.
2. Place the mower deck cut height selector in either the
top or second notch. Never cut more than 3/4” to 1”
off the grass at any one time. Attempting to cut more
grass will result in the deck plugging and cause the
engine to stall.
3. It may be necessary to cut the lawn twice to achieve
acceptable mulching performance especially on first
cuttings or if the lawn is heavily fertilized.
4. Do not attempt to cut grass when it is wet. Mulching
performance will be very poor under wet grass
conditions.
5. Maintain sharp bade(s) throughout the cutting season.
This is very important. Optimal mulching performance
cannot be obtained with a dull or nicked up blade.
26
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT
(continued):
6. Keep the underside of the mower deck clean. Remove
all grass and dirt build-up from the underside of the
pan, the baffles and deflectors after each use.
7. Alternate mower direction. This will evenly disperse
the mulched grass clippings over the lawn for even
fertilization.
If the mulching quality of the mower does not seem to be
satisfactory, try one or more of the following tips:
1. Raise the height-of-cut setting on your mower.
2. It may be necessary to cut your grass more
frequently.
3. Operate the mower at a slower ground speed.
4. Overlap cutting swaths instead of cutting a full
swath with each pass.
5. Mow across the marginal areas a second time.
6. CUT HIGH - MOW OFTEN!
27
CARE AND MAINTENANCE
CAUTION
Before performing any maintenance, turn off engine,
allow to cool & remove key. Use extreme care when
working on machinery. Do not wear watch or jewelry.
Do not wear loose fitting clothes, and observe all
common safety practices with tools.
MAINTENANCE SCHEDULE
• Check deck drive belt...........................................after 20 hours break-in
• Check crankcase oil level.........................................................before each use
•Clean grass & debris from muffler & manifold area...................before each use
• Check air intake screen..............................................................after each use
• Clean grass under deck..............................................................after each use
• Check tire pressure.....................................................................every 10 hours
• Inspect blades for sharpness........................................................every 10 hours
• Clean air filter element................................................................every 25 hours
• Grease all zerks..........................................................................every 50 hours
• Check all belts............................................................................every 50 hours
•Change engine crankcase oil............................(5 hours break-in) every 50 hours
• Change engine oil filter..............................................................every 50 hours
•Replace air filter element..........................................annually or every 100 hours
28
CARE AND MAINTENANCE
ENGINE:
For complete maintenance and operating information of
the engine, please refer to the maintenance instructions
furnished by the engine manufacturer and included in your
Zero Turn Radius mower information packet.
CAUTION
Battery contains sulfuric acid electrolyte
which is poisonous and corrosive.
BATTERY:
•This is a maintenance-free battery and the fluid level
cannot be checked.
•Charge battery if required.
OFF SEASON BATTERY STORAGE:
•DO NOT remove battery from mower.
•Clean top of battery and terminals with baking soda and
water.
•Identify each cable so they can be reconnected to the
correct terminal.
•Disconnect cables from terminals. ALWAYS disconnect
ground cable first and reconnect last.
•Charge battery.
29
CARE AND MAINTENANCE
CUTTER BLADE MAINTENANCE:
CAUTION
Stop engine and remove ignition key for
safety. Wear heavy, thick gloves when
holding onto cutter blade, avoid the sharp
edge of the blade.
Check sharpness of mower blades after every 10
hours of operation. Observe proper blade position prior
to removal.
1. Safely raise front of mower.
2. Hold or block blade from
turning.
3. Loosen blade bolt and
remove blade.
4. When replacing blade,
tighten blade bolt securely.
Refer to diagram. Be sure
blade iscentered on pilot
before tightening bolt to 60
ft. lbs.
Blades should be discarded when worn excessively.
DANGEROUS!
DO NOT USE
BLADE IN THIS
CONDITION!
New Blade
When notch starts,
discard blade
30
CARE AND MAINTENANCE
TIRES:
Correct tire pressure is essential for efficient operation
of the mower. Check tire pressure periodically. Inflate
tires to the pressure listed below.
Front tires
Rear tires
9 x 3.50-4 16-21 lbs.
16 x 6.50-8
8-14 lbs.
Lug nuts or lug bolts should be checked regularly for tightness.
31
CARE AND MAINTENANCE
BELTS:
Check belts every 50 hours. Replace any belts found to
be in poor condition.
BELT TENSION
Transaxle Drive Belt (all Zeeter Models) - P/N 7650
No adjustment required.
30” Zeeter
Manual clutch - P/N 7725
No adjustment required.
36” Zeeter
Electric Clutch - P/N 14136
Adjust idler shock mount per diagram.
Idler Weldment
Idler Shock Mount
“L” Rod
Hex Nut
5
8
Tighten or
Loosen
Hex Nut to
achieve
this
dimension
32
CARE AND MAINTENANCE
BELTS (continued):
42” Zeeter
Mower Deck Serpentine Belt
Electric Clutch - P/N 6109
Adjust idler shock mount per diagram.
Idler Weldment
Idler Shock
“L” Rod
Hex Nut
3
4
Tighten or
Loosen
Hex Nut to
achieve
this
Engine to Mower Deck Belt - P/N 5861
No adjustment required. Correct belt tension is maintained
through a fixed engine location and a spring loaded idler
system. A pulsing movement of the belt idler will be
observed both during engagement of the electric blade clutch
and actual operation of the mower deck.
Note: Engagement of the electric blade clutch switch may
produce a sharp high pitched chirp or squeal as the belt
tension loading is absorbed by the idler system. This is
normal and not a sign of failure.
33
CARE AND MAINTENANCE
Deck Removal - Zeeter 30”
1. Place cut height lever in lowest cut position.
2. Loosen belt keepers.
3. Remove deck drive belt from engine pulley.
4. Using a slight upward twisting motion, remove link
from engagement handle.
5. Turn handle fully to the left until handle clears stop on
mower deck pan. Lift handle then remove handle down
through hole in lower fender.
6. Remove hair pin cotter and washer from one end of
deck support cross shaft. Note location of remaining
shim washers used between chassis and mower deck
pan arms. Slide shaft from chassis and mower deck.
7. Remove hair pin cotter and washer from each deck
adjustment rod. Carefully push each link to disengage
from deck lift arms. At this point, deck will drop down.
8. Carefully raise and support front of chassis. Slide
mower deck to either side for removal. (Reverse
procedure to reinstall deck assembly.)
34
CARE AND MAINTENANCE
Deck Removal - Zeeter 36”
1. Place cut height lever in lowest cut position.
2. Loosen nut on belt idler shock mount until belt can be
removed from electric clutch pulley on the bottom of
the engine. Refer to illustration.
3. Remove hair pin cotter and washer from one end of
deck support cross shaft. Note location of remaining
shim washers used between chassis and mower deck
pan arms. Slide shaft from chassis and mower deck.
4. Remove hair pin cotter and washer from each deck
adjustment rod. Carefully push each link toward the
outside of the mower chassis. At this point, deck will
drop down.
5. Carefully raise and support front of chassis. Slide
mower deck to either side for removal. (Reverse
procedure to reinstall deck assembly.)
35
CARE AND MAINTENANCE
Deck Removal - Zeeter 42”
1. Place cut height lever in lowest cut position.
2. Pull belt idler back to allow belt to be removed from idler
pulley and electric clutch pulley.
3. Remove hair pin cotter and washer from one end of
deck support cross shaft. Note location of remaining
shim washers used between chassis and mower deck
plates. Slide shaft from chassis and mower deck.
4. Remove hair pin cotter and washer from each deck
L-rod. Remove L-rods from lift arms. At this point, deck
will drop down.
5. Carefully raise and support front of chassis. Slide
mower deck to either side for removal. (Reverse
procedure to reinstall deck assembly.)
Note:
36
When deck is reinstalled on frame, check that
belt is correctly routed in the grooves of all
pulleys and that belt idler is applying tension to
the back side of the belt.
CARE AND MAINTENANCE
LUBRICATION:
CHASSIS:
(5) for 30”
(6) for 36”
(7) for 42”
LOCATIONS:
(1) each front wheel caster &
front wheel hub
(1) each mower deck hub
SERVICE INTERVALS:
Every 50 hours of operation
RECOMMENDED GREASE: Name brand wheel bearing or
multi-purpose grease.Once per
season or 50 hours of operation
(3 pumps each)
37
CARE AND MAINTENANCE
CAUTION
HOT oil may cause burns. Allow engine
to cool before draining oil.
CHANGING THE ENGINE OIL:
1. The oil drain valve is located on the lower left side
of the engine crankcase.
2. Place a suitable container under the drain valve.
3. To drain, remove plug from 90o fitting.
4. After engine is drained, replace drain plug.
NOTE: Refer to engine manufacturer’s recommendations for frequency of oil changes.
38
CARE AND MAINTENANCE
OIL FILL:
1. Drain oil.
2. Clean any spilled oil from engine and chassis.
3. Replace drain plug.
4. Refill engine with type, and quantity of oil recommended
by the engine manufacturer in engine literature.
PLEASE DISPOSE OF USED OILS
AT PROPER COLLECTION CENTERS.
PROTECT YOUR ENVIRONMENT.
39
CARE AND MAINTENANCE
DRIVE SYSTEM ADJUSTMENTS:
Due to both the complex nature of the transmission and
the number of special tools required for service,
adjustments should be entrusted to your dealer.
There are a number of simple owner service items which
greatly influence the performance of the drive system.
40
1.
Front and rear tires must be inflated to proper
specifications.
2.
Rear drive chain tension.
3.
Tighteness of all controls and linkages pertaining to
the drive levers.
4.
Lubrication of both primary and final drive chains.
The use of a high quality chain lubricant is highly
recommended.
CARE AND MAINTENANCE
REAR CHAIN ADJUSTMENT:
CAUTION
Stop engine, remove key and set
parking brake before attempting to
adjust the rear chain.
Proper tension for the rear chains is accomplished through
the use of an adjuster located at mid-point of each rear chain.
To adjust, tighten the nut on top of the rubber spring until the
chain has approximately 1/4” movement up and down when
measured at mid-point. Refer to illustration.
NOTE:
Adjust rear drive chains after first 10 hours of
use and every 40 hours thereafter.
NOTE:
DO NOT OVERTIGHTEN CHAIN!
Maintenance:
Periodically remove any build-up of grass, mud or other
debris from both the spring loaded roller and the upper guide
rod. The use of a high quality chain lubricant is recommended.
41
CARE AND MAINTENANCE
ELECTRICAL SYSTEMS:
Keep all connections clean and tight.
CLEANING THE MOWER:
Wash mower periodically. Clean above and below deck.
High pressure washing and alkaline based soaps can cause
damage to bearings and other parts of the mower. After
washing your mower, start the engine and engage the
mower deck for a few minutes to disperse any water that
may have accumulated in bearings, pulleys or fans.
Note:
Allow mower to cool before washing. If bearings
are hot, they will draw moisture inside as they
dry and cause corrosion.
SERIAL NUMBERS:
The serial number is located on frame at rear of engine.
WARRANTY:
Refer to warranty information on Page 13, or see the
Warranty Registration Form in your owner’s packet.
PARTS/SERVICE:
See your Dixon dealer for replacement parts, warranty or
service.
PLEASE HELP PROTECT THE ENVIRONMENT BY AVOIDING ALL
CHEMCIALS WHICH MAY DAMAGE OR CAUSE HARM TO
PLANTS AND ANIMALS IN YOUR AREA.
42
STANDARD SERVICE PARTS LIST
ZEETER MODEL
Blades
30” Standard - P/N 2483 (Lo-lift)
30” Hi-Lift - P/N 2484
36” Standard - P/N 1324 (Lo-lift)
36” Hi Lift - P/N 1351 (R)
36” Hi Lift - P/N 1352 (L)
42” Standard - P/N 8688 (Hi-lift)
42” Lo-Lift - P/N 6236
Belts
Engine to Transmission - P/N 7650 (all models)
30” Engine to Mower Deck - P/N 7725
36” Engine to Mower Deck - P/N 14136
42” Engine to Mower Deck - P/N 5861
42” Serpentine Blade Drive - P/N 6109
BRIGGS & STRATTON AIR AND OIL FILTER
PART NUMBERS:
Refer to engine manufacturer’s manual for correct service
intervals for engine oil changes and air filter maintenance.
Protect your engine investment, use only original equipment filters.
43
TROUBLESHOOTING
1. ENGINE WON’T TURN OVER
Mower blades engaged- - - - - - - - - - - - - - - - - - - - - -disengage blades
Parking brake not on- - - - - - - - - - - - - - - - - - - - -engage parking brake
Dead battery- - - - - - - - - - - - - - - - - - - - - - - - - - - - charge or replace
Solenoid- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Ignition switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Starter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
2. ENGINE WILL TURN OVER BUT WON’T START
No fuel- - - - - - - - - - - - - - - refuel and/or clean or replace fuel filters
3. HARD TO START ENGINE
Fuel line clogged- - - - - - - - - - - - - clean fuel line and check fuel filter
4. ENGINE STARTS BUT CUTS OUT
Water in fuel- - - - - - - - - - - - - - - -drain old fuel-replace with new fuel
Clogged fuel line- - - - - - - - - - - - - - - - - - - - - - - - - - - - -check fuel filter
Fuel tank vent plugged- - - - - - - - - - - - - - - - - - - - - - - - clean fuel vent
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - check vent
5. ENGINE OVERHEATED
Air intake screen or fins clogged- - - - - -clean intake screen and fins
Oil level too low or too high- - - - - - - - - - - - - - - - - - - - - - adjust oil level
Running engine too slow- - - - - - - - - - - - - - - - - - - - - -run engine faster
44
TROUBLESHOOTING
6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD
Drive belt broken or slipping- - - - - - - - - - - - - - - - - - - replace drive belt
Transmission damage- - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
7. MOWER LOSES POWER OR TRANSMISSION OVERHEATS
Engine air filter-- - - - - - - - - - - - - - - - - - - - - - - - - - - - -clean or replace
Transmission damage- - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
8. ENGINE STALLS WHEN BLADES ARE ENGAGED
Operator not on seat- - - - - - - - - - - - - - - - - - - - - - - - - - - - sit on seat
Faulty interlock system- - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Faulty blade spindle bearing - - - - - - - - - - - - - - - - - - - - - consult dealer
Deck drive belt not properly routed- - - - - - - - - - - - - - - - - - - - reroute
Blades blocked by foreign material - - - - - - - - - - - - - -clean under deck
9. DRIVE SYSTEM
Low on power- - - - - - - - - - - - - - - - - - - - - - - - - - - - check belt tension
Mower pulls to side - - - - - - - - - - - check tire inflation/consult dealer
Mower creeps in neutral- - - - - - - - - - - - - - - - - - - - - - - -consult dealer
10. CUT QUALITY
Skips in spots- - - - - - - - - - - - check for loose belt/slow ground speed
Cut uneven left to right - - - - - - - - -check tire inflation/level the deck
Poor dispersal of grass- - - - - - - - - - -clean deck/check for loose belt
Ends of grass blades are ragged- - - - - - - - - - - - - - - - sharpen blades
45
NOTES
46
OWNER
INFORMATION
DIXON INDUSTRIES, INC.
a BLOUNT International Inc. Co.
P.O. Box 1569
Coffeyville, Ks 67337-0945
620-251-2000
FAX 620-251-4117
Date Purchased _______________________________
Mower Model Number ____________________________
Mower Serial Number ____________________________
Purchased From ________________________________
Name
________________________________
Address
________________________________
DATE OIL CHANGED:
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
DATE ENGINE TUNED:
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
47
ZTR®Mowers
WARNING:
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Dixon® and ZTR® and ZEETER® are registered trademarks
of Dixon Industries, Inc.
DIXON INDUSTRIES, INC.
a BLOUNT International Inc. Co.
P.O. Box 1569
Coffeyville, Ks 67337-0945
620-251-2000
ZEETER SERIES
Part No. 14251-0703
Download PDF

advertising