Dixon SPEEDZTR 44, 36, 42 lawn mower Operator Manual
Hirdetés
Hirdetés
® ®
SPEEDZTR
Operator Manual
SPEEDZTR 44 / 968999538 SPEEDZTR 36 / 968999539
SPEEDZTR 44 / 968999547 SPEEDZTR 36 / 968999609
SPEEDZTR 44 / 968999611 SPEEDZTR 42 / 968999689
SPEEDZTR 42 / 968999713
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
©2008 HTC. All rights reserved.
Beatrice, NE. Printed in U.S.A.
TABLE OF CONTENTS
INTRODUCTION .......................................................4
Driving and Transport on Public Roads .................4
Towing ...................................................................4
Operating ...............................................................4
Good Service .........................................................5
SYMBOLS AND DECALS .........................................6
SAFETY .....................................................................8
General Operation .................................................8
Personal Safety Equipment .................................10
Slope Operation ..................................................10
Safe Handling of Gasoline ...................................12
General Maintenance ..........................................13
Transport .............................................................15
Roll Over Protection System (ROPS) ..................16
CONTROLS .............................................................17
Motion Control Levers .........................................18
Tracking .........................................................18
Seat Adjustment Lever ........................................19
Bypass Linkage ...................................................19
Fuel Tank .............................................................20
Ignition Switch .....................................................21
Choke Control .....................................................21
Throttle Control ....................................................21
Blade Switch ........................................................22
Circuit Breaker .....................................................22
Parking Brake ......................................................22
Mower Deck Cut Height Adjustment ....................23
OPERATION ............................................................24
Training ................................................................24
Steering ...............................................................24
Before Starting ....................................................25
Starting the Engine ..............................................25
Weak Battery .......................................................28
Jumper Cables ..............................................28
Running ...............................................................29
Operating on hills ................................................30
Mowing Tips ........................................................31
Stopping the Engine ............................................32
Manual Transport ................................................33
MAINTENANCE ......................................................34
Maintenance Schedule ........................................34
Battery .................................................................36
Ignition System ....................................................37
Safety System .....................................................37
Engine Cooling Air Intake ....................................38
Throttle Cable ......................................................38
Choke Cable ........................................................38
Air Filter ...............................................................39
Fuel Filter ............................................................40
Fuel Pump Air Filter .............................................40
Tire Pressures .....................................................41
Parking Brake ......................................................41
V-belts .................................................................41
Pump Belt ............................................................43
Blades .................................................................44
Mower Deck ........................................................45
Adjusting Mower Deck ...................................45
Leveling Mower Deck ....................................45
Caster Wheels .....................................................46
Hardware .............................................................46
Cleaning ..............................................................46
Tracking Adjustment ............................................47
EZT Transaxle .....................................................47
Purging Procedure ........................................47
Anti-scalp Rollers ................................................47
Lubrication Schedule ...........................................48
General ................................................................48
LUBRICATION .........................................................48
Lubricating the Cables .........................................49
Following the Lubrication Schedule .....................49
Oil Level ..............................................................51
Oil Filter ...............................................................51
TROUBLE SHOOTING ...........................................52
STORAGE ...............................................................55
Winter Storage ....................................................55
Service ................................................................55
SCHEMATIC ............................................................56
TECHNICAL DATA ..................................................57
Accessories .........................................................57
Torque Specifications ..........................................57
CONFORMITY CERTIFICATES ..............................66
USA Requirements ..............................................66
SERVICE JOURNAL ...............................................67
Delivery Service ..................................................67
After the First 5-8 Hours ......................................68
25-Hour Service ..................................................69
50-Hour Service ..................................................70
100-Hour Service ................................................71
300-Hour Service ................................................72
At Least Once Each Year ....................................73
Congratulations
Thank you for purchasing a Dixon ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the safety of the operator and others.
It can also considerably increase the life span of the machine and increase its resale value.
If you sell your machine, be sure to give the operator’s manual to the new owner.
The final chapter of this operator’s manual provides a
Service Journal. Ensure that service and repair work are documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information. Take the operator’s manual along when the machine is taken to your dealer for service.
General
In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.
Continuous dedication to improve our products require that specifications and design are subject to change without notice.
Driving and Transport on Public Roads
Check applicable road traffic regulations before transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.
INTRODUCTION
Towing
Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and possible serious injury to the operator.
Operating
This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones, tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.
Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to maintain this machine.
Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail.
Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage.
4-
DIXON
INTRODUCTION
Good Service
Dixon’s products are sold only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator’s manual.
When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional:
This Operator’s Manual belongs to the machine with the manufacturing number:
Engine
Transmission
Manufacturing Number
The machine’s manufacturing number can be found on the printed plate affixed to the left in the engine compartment. Stated on the plate, from the top are:
•
•
The machine’s type designation (I.D.).
The manufacturer’s type number (Model).
• The machine’s serial number (Serial no.)
Please have the type designation and serial number available when ordering spare parts.
•
•
The engine’s manufacturing number is stamped on one of the valve covers.
The plate states:
•
The engine’s model.
The engine’s type.
Code
Please have these available when ordering spare parts.
DIXON
-5
SYMBOLS AND DECALS
These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.
WARNING!
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx
xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
IMPORTANT INFORMATION
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.
R N
Reverse Neutral Fast Slow Choke Fuel
Warning! Parking Brake CE conformity marking. Only for
European market
Warning! Rotating blades, Do not touch parts keep away from the discharge deck
Battery acid is corrosive, explosive and flammable
6-
DIXON
Use protective glasses
Do not stand here
Use protective gloves
Noise emissions to the surroundings in accordance with the European Union’s directive. The machine’s emission is stated in the chapter TECHNICAL DATA and on the decals.
Only machines for European market
Read
Operator’s
Manual
SYMBOLS AND DECALS
Shut off engine and remove key before performing any maintenance or repair work
Keep a safe distance from the machine
Use on slopes no greater than 10°
No passengers
Whole body exposure to thrown objects
Severing of fingers and toes
Do not open or remove safety shields while engine is running
Careful backing up, watch for other people
Careful going forward, watch for other people
Moving sharp blades under cover
DIXON
-7
SAFETY
WARNING!
THIS CUTTING MACHINE IS CAPABLE
OF AMPUTATING HANDS AND FEET
AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING
SAFETY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR
DEATH.
These instructions are for your safety. Read them carefully.
General Operation
1. Read, understand, and follow all instructions on the machine and in the manual before starting.
2.
3.
Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
Only allow responsible adults, who are familiar with the instructions, to operate the machine.
4.
5.
6.
7.
8.
9.
10.
11.
Clear the area of any objects such as rocks, toys, and wire, which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers. The machine is only intended for use by one person.
Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working
Slow down before turning.
Never leave a running machine unattended.
Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
WARNING!
This symbol means that important safety instructions need to be emphasized. It concerns your safety.
8011-512
Read the operator’s manual before starting the machine
Clear the area of objects before mowing
8011-513
D-
DIXON
SAFETY
1.
2.
3.
4.
5.
Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge chute.
Operate machine only in daylight or good artificial light.
Do not operate the machine while under the influence of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine into a trailer or truck.
6.
7.
8.
9.
10.
Always wear eye protection when operating machine.
Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for wheel weights or counterweights.
Anyone who operates this machine must first read and understand this Operation Manual.
Local laws may regulate the age of the user.
Keep machine free of grass, leaves or other debris buildup which can touch hot exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.
Never take passengers
8011-520
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
DIXON
-9
SAFETY
Personal Safety Equipment
WARNING!
When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
•
•
•
•
•
•
•
Make sure that you have first aid equipment close at hand when using the machine.
Never use the machine when barefoot.
Always wear protective shoes or boots, preferably with steel toe caps.
Always wear approved protective glasses or a full visor when assembling or driving.
Always wear gloves when handling the blades.
Never wear loose clothing that can get caught in moving parts.
Use ear protectors to avoid damage to hearing.
Slope Operation
Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
1.
2.
3.
Mow up and down slopes (10 degrees maximum), not across.
Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
Choose a low ground speed so that you will not have to stop while on the slope.
4.
5.
6.
Do not mow on wet grass. Tires may lose traction.
Avoid starting, stopping, or turning on a slope.
If the tires lose traction, disengage the blades and proceed slowly straight down the slope.
Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.
Personal protective equipment
Mow up and down, not side to side
8011-670a
6003-004
WARNING!
Do not drive up or down hills with slopes greater than 10 degrees. And do not drive across any slopes.
D-
DIXON
7.
8.
9.
10.
Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine.
Do not use on steep slopes.
Do not try to stabilize the machine by putting your foot on the ground.
Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.
SAFETY
8011-509
Be extra cautious when driving on slopes
•
•
Children
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.
•
•
Be alert and turn machine off if a child enters the area.
Before and while backing, look behind and down for small children.
• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation.
Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.
Never allow children to operate the machine
8011-517
Keep children away from work area
8011-518
DIXON
-11
SAFETY
WARNING!
The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.
•
•
•
•
•
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
•
•
Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
Use only approved gasoline container.
•
•
•
•
•
•
•
•
Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling.
Never fuel the machine indoors.
Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliance.
Before you begin refueling, minimize the risk of static electricity by touching a metal surface.
Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from the vehicle when filling.
Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lockopen device.
If fuel is spilled on clothing, change clothing immediately.
Never overfill fuel tank. Replace gas cap and tighten securely.
Do not start the engine near spilled fuel.
Never use gasoline as a cleaning agent.
If leaks arise in fuel system, engine must not be started until problem has been resolved.
Check the fuel level before each use and leave space for the fuel to expand, as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.
Never fill the fuel tank indoors
8011-516
WARNING!
The engine and the exhaust system become very hot during operation.
There is risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling.
D-
DIXON
SAFETY
General Maintenance
• Never operate machine in a closed area.
•
•
Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
Never tamper with safety devices. Check their proper operation regularly.
•
•
•
•
•
•
•
•
•
•
•
•
•
Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.
If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.
Never make any adjustments or repairs with the engine running.
Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary.
Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as required.
Maintain or replace safety and instruction labels, as necessary.
Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Be very careful when handling battery acid.
Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water.
Acid in the eyes can cause blindness, contact a doctor immediately.
Be careful when servicing the battery.
Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks.
The battery can explode and cause serious injury/damage.
Never drive the machine in an enclosed space
WARNING!
Use protective glasses for maintenance work.
WARNING!
The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.
8011-515
DIXON
-13
SAFETY
•
•
•
•
Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition.
Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.
6003-009
Do not smoke when performing maintenance on the battery.
The battery can explode and cause serious injury/damage.
WARNING!
Avoid electrical sparking and its consequences by the following routines:.
•
•
•
•
•
•
•
•
•
Use protective goggles.
Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.
Never work with the starter circuit if there is spilled fuel.
Disconnect the chassis cable from the battery first and reconnect it last.
Do not make a bridge short circuit across the starter relay to run the starter.
Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.
Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.
Never make adjustments with the engine running.
The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
D-
DIXON
Risk of sparking
8009-728
SAFETY
•
•
•
•
•
The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them.
Check the parking brake’s functionality regularly. Adjust and service as necessary.
The mulch blades should only be used in familiar areas when higher quality mowing is desired.
Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine. Allow the machine to cool before putting it in storage.
Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.
Transport
• The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.
•
•
Use an approved trailer to transport the machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting.
Do not operate this machine on public roadways.
•
•
•
•
Check and abide by local traffic regulations before transporting the machine on any road.
Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower.
They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator.
Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed.
Do not lift! The machine is not intended to be lifted by hand.
Regularly clean deck
8011-514
WARNING!
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury.
If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.
IMPORTANT INFORMATION
The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle.
Always reverse the machine onto the transport vehicle to avoid tipping it over.
DIXON
-15
SAFETY
•
•
•
•
•
•
Roll Over Protection System (ROPS)
The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS is an accessory.
•
•
Do not use ROPS as a lifting, attaching or anchoring point.
Do not use ROPS for wrecking or towing.
•
•
•
•
•
•
•
•
Do not exceed Max GVW: 2822 lbs/1283 kg.
Read machine operator´s manual before each use.
Securely fasten your seat belt if the unit has a
ROPS.
Where possible, avoid operating the unit near ditches, embankments and holes.
Reduce speed when turning, crossing slopes and on rough, slick or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going, especially at row ends, on roads and around trees.
Do not permit others to ride.
Operate the mower smoothly - no jerky turns, starts or stops.
When mower is stopped, set brakes securely and use park brake.
If any part of ROPS is damaged, the entire
ROPS must be replaced.
Check all bolts including seat belt for correct torque before each use.
Check ROPS structure for damage before each use.
ROPS bar is NOT intended for use in sub zero temperatures.
WARNING!
The rollover protection system’s capabilities may be impaired by damage if the mower is overturned or if alteration to the ROPS occurs. If these conditions take place, the total structure MUST be replaced.
WARNING!
This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine’s system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
D-
DIXON
CONTROLS
This operator’s manual describes the Dixon Zero
Turn Rider. The rider is fitted with either a Briggs &
Stratton or Kohler four-stroke overhead valve engine developing 16 - 22 horse power.
Transmission from the engine is made via two beltdriven hydraulic pumps, which in turn drive a hydraulic motor for each drive wheel. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.
10
1
3
4
9
1. Motion Control Levers
2. Seat Adjustment Lever
3. Bypass Linkage
4. Fuel Tank
5. Ignition Switch
6. Choke Control
5
7
8
6
11
7. Throttle
8. Blade Switch
9. Circuit Breaker
10. Parking Brake
11. Lift Lever
2
DIXON
-17
CONTROLS
Motion Control Levers
The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.
When both controls are in the neutral position (N), the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.
Tracking
If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (1 bar). Tracking must be checked on a flat and level concrete or blacktop surface. If unit still does not track straight, contact a Dixon dealer for adjustment.
Steering controls
8050-106
WARNING!
The machine can turn very rapidly if one steering control is moved much further forward than the other.
1. Forward
2. Neutral
3. Neutral slot, Neutral lock
4. Reverse
Motion control lever pattern (right side)
8050-166-1
18-
DIXON
CONTROLS
Seat Adjustment Lever
The seat can be adjusted lengthways. When making adjustments, sit on the seat. Slide the lever to the side and maneuver seat to appropriate placement and release lever.
Seat adjustment
Bypass Linkage
Unlocking Transmission
When pushing or pulling the mower, be sure to engage the bypass linkages.
1. Always turn off engine before engaging or disengaging the hydro release (free wheel) lever. Never attempt to move the lever with the engine running.
2.
3.
Lift the seat to access release levers. Push the hydro release levers toward the rear of the machine and inward until notches lock in place on frame. Release park brake.
To engage the transmissions, move the release levers outward so they return to normal position.
Push lever in and lock notch on frame
(2 places)
Bypass linkages
IMPORTANT INFORMATION
Before pushing or towing tractor, transmission must be unlocked and park brake released. The tractor should never be pulled at more than 2 miles per hour (3.2 km/h) or for distances over ¼ mile (.402 km).
Trailer the unit for distances over ¼ mile.
8050-165
8050-811
DIXON
-19
CONTROLS
Fuel Tank
The machine has one fuel tank, just behind the seat.
The tank capacity is 4.5 gallons (17 liters).
The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also
Technical Data concerning ethanol fuel. Methanol fuel is not allowed.
When operating below 32°F (0°C) use fresh, clean winter grade gasoline to help insure good cold weather starting.
8050-106
WARNING!
Gasoline is highly flammable.
Observe caution and fill the tank outdoors. (See Safety)
Fuel tank
WARNING!
Fill to the bottom of the filler neck.
Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
WARNING!
The engine and the exhaust system, become very hot during operation.
Risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling.
IMPORTANT INFORMATION
Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.
20-
DIXON
CONTROLS
Ignition Switch
The ignition key is placed on the driver’s panel and is used to start and stop the engine.
IMPORTANT INFORMATION
Do not run the starter for more than five seconds each time. If the engine does not start, wait about 10 seconds before retrying.
Ignition Switch
Choke Control
The choke is used for cold starts to provide the engine with a richer fuel mixture.
Two choke options are available, depending on model.
For units with a separate choke control, pull the choke control knob up. For units with choke/throttle combinations, push the throttle control all of the way forward into the indicated slot.
Choke control
Throttle Control
The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower
Deck.
In order to increase or decrease the engine speed, the control is moved.
Avoid idling the engine for long periods, as there is a risk of fouling the spark plug.
USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging.
Choke and throttle control
8050-816
8050-817
8050-816
DIXON
-21
CONTROLS
Blade Switch
In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.
Circuit Breaker
The circuit breaker provides protection for the electrical system by (1) 15 amp circuit breaker. If the circuit breaker trips, push the button to reset. If the condition repeats, consult a dealer for inspection and repair.
Blade switch
Circuit breaker
Parking Brake
The parking brake is found on the operator’s left. Pull the lever upward to activate the brake and downward to release it.
The park brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion. The engine will stop if the park brake is engaged while the control levers are in the drive position.
IMPORTANT INFORMATION
The machine must stand absolutely still when applying the parking brake. Always set the parking brake before dismounting. Release the parking brake before moving the mower.
Engaged parking brake
22-
DIXON
8050-816
8050-816
8050-823
CONTROLS
Mower Deck Cut Height Adjustment
Located on the right front of the frame, the lift lever pedal controls the cutting height. The deck cutting height is obtained by pressing the foot pedal forward to lift the deck. To lower the deck, apply pressure to the top side of the foot pedal and allow it to pivot into the desired cutting height notch. Secure the desired cut height with pin.
The cutting height range is from 1½" (38 mm) to 5½"
(140 mm) in ½" (13 mm) increments. The heights are measured from the ground up to the blade tip with the engine not running.
Cut height lift pedal
IMPORTANT INFORMATION
Always use the high position to transport.
IMPORTANT INFORMATION
In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar).
8050-806
DIXON
-23
OPERATION
Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine.
Training
Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities.
We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power. Additionally, we suggest when first operating the mower, use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until operator becomes comfortable with controls. We also suggest first time users, or new users to Zero Turn mowers to become familiar with the mower’s movement on a hard surface, such as concrete or blacktop PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability, they may damage turf due to overly aggressive maneuvers.
IMPORTANT INFORMATION
When control levers are in the reverse position they return to neutral when released.
This may cause the mower to suddenly stop.
the control levers have not been moved forward or backwards, mower will not move. Slowly move both control levers forward slightly. This will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving backwards. Push forward on control levers to the neutral position and mower should stop moving.
To turn to the right
While moving in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that direction.
To turn to the left
While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that direction.
To zero turn
While moving in a forward direction, first pull both control levers back until the mower stops or slows dramatically. Then by alternating one lever slightly to the forward position and the other in the reverse position.
Steering
To move forward and backward
The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel.
First time users should push mower (see “Moving by
Hand” in the “Operation” section) to an open, flat area, without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must be in the seat, start engine (see “Before Starting” in “Operation” section), adjust engine speed to idle, disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as
24-
DIXON
OPERATION
Before Starting
• Read the sections Safety Instructions and
Controls before starting the machine.
•
•
Perform the daily maintenance before starting (see Maintenance Schedule in the
Maintenance section).
Check that there is sufficient fuel in the fuel tank.
•
•
• Adjust the seat to the desired position.
The following conditions must be fulfilled before the engine can be started:
The driver must be seated on the seat.
The blade switch for engaging the mower blades must be depressed.
• The parking brake must be on.
• Both steering controls must be in the locked
(outer) neutral position.
Starting the Engine
1. Sit on the seat.
2. Raise the mower deck with the foot pedal to the transport position.
3. Activate the parking brake.
Start conditions
4. Disengage the mower blades by depressing the blade switch.
Raise the mower deck
Blade switch
8050-822
8050-117
8050-816
DIXON
-25
5. Move the steering controls outward to the locked (outer) neutral position.
OPERATION
6. Move the throttle to the middle position. If the engine is cold, the throttle control should be pushed forward to its choke position. For units with a separate choke control, pull the choke control knob up.
8050-777
Steering controls in the outward, locked neutral position
8050-816
7. Press in and turn the ignition key to the start position.
Set the throttle
Turn to the start position
8050-780
26-
DIXON
OPERATION
8. When the engine starts, immediately release the ignition key back to the run position.
IMPORTANT INFORMATION
Do not run the starter for more than 5 seconds each time. If the engine does not start, wait about 10 seconds before retrying.
9. Set the desired engine speed with the throttle.
Allow the engine to run at a moderate speed,
“half throttle”, for 3-5 minutes before loading it too heavily.
USE FULL THROTTLE WHEN MOWING
(no choke).
Return to run position
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
Set the engine speed
8050-781
8050-818
DIXON
-27
OPERATION
Weak Battery
WARNING!
Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.
If your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance
Section.)
IMPORTANT INFORMATION
Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.
If “jumper cables” are used for emergency starting, follow this procedure:
Jumper Cables
1. Connect each end of the RED cable to the
POSITIVE (+) terminal on each battery, taking care not to short against chassis.
2.
3.
Connect one end of the BLACK cable to the
NEGATIVE (-) terminal of the fully charged battery.
Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery.
To remove cables, reverse order
1. Remove BLACK cable first from chassis and then from the fully charged battery.
2. Remove RED cable last from both batteries.
Jumper cable connection
28-
DIXON
8011-642
OPERATION
Running
1. Release the parking brake by moving the lever downward.
Your mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.
2. Move the steering controls to the neutral position (N).
IMPORTANT INFORMATION
The mower deck’s anti-scalp rollers should be evenly adjusted.
3. Select the cutting height using the cutting height pedal.
Released parking brake
WARNING!
Ensure that no one is near mower when engaging blade switch. Make sure the work area is free from objects that could be thrown by the rotating blades.
Select cutting height
4.
5.
Engage the mower deck by pulling out the blade switch.
Move throttle control to full throttle (not choke)
The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Turning on the spot can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position.
Engage mower deck
8050-821
8050-117
8011-669
DIXON
-29
OPERATION
Operating on hills
Read the Safety Instructions “Driving on Slopes” in the
“Safety Instructions”.
•
•
The slowest speed possible should be used before starting up or down hills.
Avoid stopping or changing speed on hills.
• If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake.
WARNING!
Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes.
•
•
•
To restart movement, release the parking brake.
Pull the control levers back to the center of the mower and press forward to regain forward motion.
Make all turns slowly.
Stopping conditions
IMPORTANT INFORMATION
Control levers return to neutral when released. This may cause the mower to suddenly stop.
Released parking brake
8050-822
8050-783
30-
DIXON
OPERATION
Mowing Tips
• Observe and flag rocks and other fixed objects to avoid collisions.
•
•
•
Begin with a high cutting height and reduce it until the desired mowing result is attained.
The average lawn should be cut to 2½” (64 mm) during the cool season and over 3” (76 mm) during the hot months. For healthier and better looking lawns, mow often after moderate growth.
For best cutting performance, grass over 6”
(15 cm) in height should be mowed twice.
Make the first cut relatively high; the second to the desired height.
The mowing result will be best with a high engine speed (the blades rotate rapidly) and low speed (the rider moves slowly). If the grass is not too long and dense, the driving speed can be increased without negatively affecting the mowing result.
The finest lawns are obtained by mowing often. The lawn becomes more even and the grass clippings more evenly distributed over the mown area. The total time taken is not increased as a higher operating speed can be used without poor mowing results.
•
•
•
•
Avoid mowing wet lawns. The mowing result is poorer because the wheels sink into the soft lawn, clumps build, and the grass clippings fasten under the cowling.
Hose the mower deck underside with water after each use. When cleaning, the mower deck shall be raised into the transport position. Make sure the mower is cooled and the engine is off.
Use compressed air to clean top surface of the deck. Avoid flooding water on top surface, engine and electrical components.
When the mulching kit is used, it is important that the mowing interval is frequent.
Mowing pattern
WARNING!
Clear the lawn of stones and other objects that can be thrown out by the blades.
WARNING!
Never drive the rider on terrain that slopes more than 10 degrees. Mow slopes up and down, never side to side. Avoid sudden directional changes.
8050-819
DIXON
-31
OPERATION
Stopping the Engine
Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling.
• Disengage the mower deck by depressing the blade switch.
•
•
•
•
•
Raise the mower deck by depressing the pedal forward to the transport position.
When the machine is standing still, activate the parking brake by pulling the lever upward.
Move the throttle to the minimum position
(tortoise symbol). Turn the ignition key to the stop position.
Move the steering controls outward.
Remove key. Always remove key when leaving the mower to prevent unauthorized use.
Disengage the mower deck
Select cutting height
88011-668
8050-117
IMPORTANT INFORMATION
Leaving the ignition switch in any other position than “OFF” will cause the battery to be discharged.
32-
DIXON
Engaged parking brake
8050-823
Manual Transport
•
•
WARNING!
Make no adjustments without:
• the engine stopped the ignition key removed the parking brake activated
OPERATION
Unlocking Transmission
When pushing or pulling the mower, be sure to engage the bypass linkages.
•
•
•
Always turn off engine before engaging or disengaging the hydro release (free wheel) lever. Never attempt to move the lever with the engine running.
Lift the seat to access release levers. Push the hydro release levers toward the rear of the machine and inward until notches lock in place on frame. Release park brake.
To engage the transmissions, move the release levers outward so they return to normal position
Push lever in and lock notch on frame
(2 places)
Bypass linkages
8050-811
DIXON
-33
MAINTENANCE
Maintenance Schedule
The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation.
Read “Maintenance” in the Safety Instructions section.
●
= Described in this manual
♦
= Not described in this manual
1)
First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.
2)
In dusty conditions, cleaning and replacement are required more often.
3)
Performed by authorized service workshop.
Maintenance
Check the parking brake
Check the engine’s oil level (every refueling)
Check the safety system
Check for fuel and oil leakages
Check/clean the engine’s cooling air intake
Check the mower deck
Check for loose hardware (screws, nuts)
Clean under the mower deck
Start the engine and blades, listen for unusual sounds
Check for damage
Thoroughly clean around the engine
Clean around belts, belt pulleys
Check the tire pressures
Check battery
Sharpen/Replace mower blades
Clean the engine’s cooling air intake 2)
Clean the air cleaner’s pre-filter 2) (foam)
Clean the air cleaner’s filter cartridge 2) (paper filter)
Check/adjust the parking brake
Inspect muffler/Spark arrester
Check the fuel pump's air filter 2)
Daily
Before After
Weekly At least once each year
Maintenance interval in hours
25 50 100 300
●
♦
●
●
♦
♦
♦
♦
●
●
●
●
●
● ●
●
●
♦
♦
● ●
●
●
●
♦
♦
34-
DIXON
MAINTENANCE
Maintenance
Check/adjust throttle cable
Check the condition of belts, belt pulleys
Change the engine oil
1)
Replace the engine oil filter
Clean/replace the spark plugs
Replace the fuel filter
Replace the air filter (paper filter)
2)
Check the caster wheels (every 200 hours)
Replace the air cleaner’s pre-filter
2)
(foam)
Check/adjust the mower deck
Check the engine valve clearance
3)
Perform the 300-hour service
3)
Lubricate according to Lubrication Schedule
Clean fins of oil cooler
Daily
Before After
Weekly At least once each year
Maintenance interval in hours
25 50 100 300
●
●
●
●
●
●
●
●
●
●
♦
♦
●
●
♦
● ● ● ● ●
♦ ♦
●
♦
1)
First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.
2)
In dusty conditions, cleaning and replacement are required more often.
3)
Performed by authorized service workshop.
●
= Described in this manual
♦
= Not described in this manual
•
•
•
•
•
WARNING!
Before performing any service or adjustment checklist
Engage the parking brake.
Place the Blade-switch in the disengaged position.
Turn the ignition switch to “OFF” position and remove the key.
Make sure the blades and all moving parts have completely stopped.
Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.
DIXON
-35
MAINTENANCE
1.
2.
3.
Battery
Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.
Keep battery and terminals clean.
Keep battery bolts tight.
Recharge at 6-10 amperes for 1 hour
Cleaning battery and terminals
Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.
1.
2.
Lift seat and rotate forward.
Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.
3. Rinse the battery with plain water and dry.
4.
5.
6.
Clean terminals and battery cable ends with wire brush until shiny.
Coat terminals with grease or petroleum jelly
Reinstall battery.
Replacing battery
1. Lift seat and rotate forward.
2.
3.
4.
5.
Open terminal access doors.
Using two ½” wrenches disconnect BLACK battery cable then RED battery cable.
Position deck to lowest setting.
Front underside of frame, remove the nuts that secure the battery hold-down.
6.
7.
8.
9.
10.
Carefully remove the battery from the mower.
Install new battery with terminals in the same position as the old battery.
Reinstall battery hold-down and secure with nuts removed in Step 5.
First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.
Connect BLACK grounding cable to negative
(-) battery terminal with remaining hex bolt and hex nut
11.
12.
Tighten securely.
Lower seat
Always use protective glasses when handling the battery.
IMPORTANT INFORMATION
Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
Always use two wrenches for the terminal screws.
WARNING!
Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparks from accidental grounding.
Remove battery hold-down to replace battery
8050-109
36-
DIXON
MAINTENANCE
Ignition System
The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance.
For recommended spark plug, see Technical Data.
1. Remove the ignition cable boot and clean around the spark plug.
2.
3.
4.
5.
6.
7.
Remove the spark plug with a spark plug socket wrench.
Check the spark plug. Replace the spark plug if fouled, the electrodes are burned and if the insulation is cracked or damaged. Clean the spark plug with a steel brush if it is to be reused.
Measure the electrode gap with a gapping tool.
The gap should be .030” (0.75 mm). Adjust as necessary by bending the side electrode.
Reinsert the spark plug, turning by hand to avoid damaging the threads.
After the spark plug is seated, tighten it using a spark plug wrench so that the washer is compressed. A used spark plug should be turned 1/8 of a turn from the seated position. A new spark plug should be turned ¼ turn from the seated position.
Replace the ignition cable.
Safety System
The machine is equipped with a safety system that prevents starting or driving under the following conditions.
The engine can only be started when:
•
•
The mower deck is disengaged.
• The steering controls are in the outer, locked neutral position.
The driver is sitting in the driver’s seat.
The parking brake is on.
Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.
If the machine starts when one of these conditions is not met, turn the machine off and repair the safety system before using the machine again.
• Make sure the engine stops when the parking brake is not engaged and the operator leaves the seated position.
• Check that the engine stops if the mower blades are engaged and the driver temporarily stands up.
IMPORTANT INFORMATION
Fitting the wrong spark plug type can damage the engine.
Inadequately tightened spark plug can cause overheating and damage the engine.
Tightening the spark plug too hard can damage the threads in the cylinder head.
Measure the electrode gap
Start conditions
8011-054
8050-822
DIXON
-37
MAINTENANCE
Engine Cooling Air Intake
Check that the engine’s cooling air intake is free from leaves, grass, and dirt.
If the cooling air intake is clogged, engine cooling deteriorates, which can lead to engine damage.
Check and clean the cooling air intake
Throttle Cable
Check that the engine responds to throttle increases and that a good engine speed is attained at full throttle.
If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made as follows for the lower cable:
1.
2.
3.
Loosen the clamping screw for the cable’s outer casing and move the throttle to the full throttle position.
Check that the throttle cable is mounted in the correct hole in the lower lever, see illustration.
Push the throttle cable’s outer casing as far to the left as possible and tighten the clamping screw.
Choke Cable
If the engine produces black smoke or is difficult to start, this may be because the choke cable is incorrectly adjusted (upper cable).
If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made as follows:
1. Loosen the clamping screw for the cable’s outer casing and move the choke lever to the full choke position.
2. Check that the choke cable is mounted in the upper lever, see illustration. Push the choke cable’s outer casing as far to the right as possible and tighten the clamping screw.
Adjusting the throttle cable
Adjusting the choke cable
38-
DIXON
8011-625
8011-554
8011-555
MAINTENANCE
Air Filter
If the engine seems weak or runs unevenly, the air filter may be clogged. If run with a dirty air filter, the spark plugs can become fouled, disrupting operation.
For this reason, it is important to replace the air filter regularly (see the heading Maintenance Schedule for the proper service interval).
WARNING!
The engine and the exhaust system become very hot during operation.
There is a risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes.
Remove the air filter cowling
Cleaning/replacing the air filter is carried out as follows:
1. Remove the plastic fastener on the top of the air filter cowling and remove the air filter cowling.
2. Remove the foam rubber pre-filter and clean using a mild detergent. Squeeze it dry with a clean cloth.
3. Remove the wing nuts for the air filter and remove the paper filter.
Remove pre-filter
8011-768
8011-557
Remove paper filter
8011-558
DIXON
-39
MAINTENANCE
IMPORTANT INFORMATION!
Do not use compressed air to clean the air filter. Do not wash the paper filter. Do not oil the paper filter.
4. Tap the paper filter against a fixed surface to remove dust. If the paper filter is still dirty, it must be replaced.
Refit the air filter as follows:
1. Check that the seal on the bottom of the paper filter is whole.
2.
3.
4.
Mount the paper filter in the air filter housing and tighten the wing nuts.
Refit the pre-filter on the paper filter.
Replace the cowling over the air filter housing.
Do not over tighten the plastic fastener.
Fuel Filter
Replace the line-mounted fuel filter every 100 hours
(once per season) or more regularly if it is clogged.
Replace the filter as follows:
1. Move the hose clamps away from the filter.
Use flat-nosed pliers.
2.
3.
Pull the filter loose from the hose ends.
Push the new filter into the hose ends. Position the filter with the “FLOW” arrow pointing up toward the carburator. If necessary, a soap solution can be applied to the filter ends to ease mounting.
4. Move the hose clamps back toward the filter.
Fuel Pump Air Filter
Regularly check that the fuel pump’s air filter is free from dirt.
Remove the screws and open the pump, no hoses need be removed.
The filter can be cleaned with a brush if necessary.
Replace the filter on the console.
Remove dust
Fuel filter
Fuel pump air filter
40-
DIXON
8009-181
8009-146
8009-147
Tire Pressures
All four tires should have a pressure of
15 psi / 103 kPa /1 bar.
MAINTENANCE
WARNING!
The machine must be standing absolutely still when the park brake is engaged.
Parking Brake
Visually check that no damage is found on the lever, linages, or switch belonging to the parking brake.
Perform a stand still test and check that there is a braking action.
To adjust the parking brake, contact the Dixon service workshop.
WARNING!
Faulty adjustment can cause an accident.
Check tire pressure
Engaged parking brake
V-belts
Deck belt
Inspect every 50 hours of operation. Check for severe cracking and large nicks.
NOTE: The belt will show some small cracks in normal operation.
Belt tension is manually adjustable. Turn bolt on deck eyebolt to adjustment tension.
NOTE: Belt deflection or movement should be approximately ¼”(6mm) when measured at midpoint between pulleys. Periodically inspect both belt and idler systems.
Adjusting belt tension
8011-564
8050-823
Tension
Eyebolt
8050-824
DIXON
-41
MAINTENANCE
Deck belt removal
1. Park on a level surface. Apply parking brake.
2.
3.
Lower the deck into the lowest cutting position.
Remove bolts from belt shields and remove shields.
4. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.
5. Carefully roll the belt over the top of the cutter housing pulleys and remove belt.
Deck belt installation
NOTE: For ease in installing the deck belt, refer to the routing decal on bottom of seat.
1. Wrap the deck belt around the electric clutch pulley that is located on the engine shaft.
2.
3.
4.
5.
Route the belt forward between the EZT
(E-Series Zeroturn Transaxles) and up onto the deck.
Place belt around spring loaded idler pulley.
Wrap the belt around the stationary idler pulley and around the mandrel housings.
Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt.
6.
7.
8.
Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed.
Adjust tension with deck eyebolt.
Replace belt shields on both mandrel housings and secure with fasteners.
1. Shield bolts
2. Belt shields
Removing deck belt
2
1. Clutch pulley
2. Deck belt
Belt routing, deck belt - 44" deck
1
1
2
1
2
8050-824
8050-825
1. Clutch pulley
2. Deck belt
Belt routing, deck belt - 36" and 42" deck
8050-826
42-
DIXON
MAINTENANCE
Pump Belt
Replacing EZT (E-Series Zeroturn Transaxle) belt
Park the mower on a level surface. Engage the parking brake.
EZT belt removal
NOTE: Be careful not to damage the fan blades on the EZT´s as this can affect cooling or damage the
EZT´s
•
•
Remove the deck belt (see Deck Belt Removal in this section of the manual).
Create slack in the belt by removing the spring on the pump idler arm.
•
•
•
Belt installation
• Wrap the EZT belt around the EZT pulleys
•
The belt should now be able to be removed from the engine pulley and EZT pulleys.
Route the belt around the inside of the idler pulley.
Wrap the belt around the engine pulley.
Reattach the spring on the pump idler arm.
•
•
Install clutch on to engine shaft (pulley side down) make sure key is installed and align the clutch anti rotation tab into slot on clutch.
Secure clutch, install wire.
Reinstall the deck belt onto the electric clutch belt (see Deck Belt Removal in this section of the manual).
DIXON
-43
MAINTENANCE
Blades
In order to attain the best mowing effect, it is important that the blades are well sharpened and not damaged.
WARNING!
Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.
Bent or cracked blades or blades with large nicks should be replaced.
Check the blade mounts.
Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the service workshop decide whether the blade can be repaired/ ground or must be replaced.
IMPORTANT INFORMATION
The sharpening of blades should be carried out by an authorized service workshop.
Blade replacement
• Remove blade bolt by turning counterclockwise.
•
•
Install new or re-sharpened blade with stamped “GRASS SIDE” facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing.
Install and tighten blade bolt securely.Torque blade bolt to 27-35 ft/lb (35-45 Nm).
IMPORTANT INFORMATION
Special blade bolt is heat treated.
Replace with a Husqvarna bolt if required.
Do not use lower grade hardware than specified.
Check the blades
1
1. Blade
2. Center hole
3. Cutter housing
4. Blade bolt
5. Lockwasher
Blade attachment
4
2
5
3
44-
DIXON
8011-604
8050-802
MAINTENANCE
Mower Deck
WARNING!
Before performing any service or adjustment, check the following list:
1. Engage the parking brake.
2. Place the blade switch in the disengaged position.
3. Turn ignition switch to “OFF” position and remove the key.
4. Make sure the blades and all moving parts have completely stopped.
5. Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.
Adjusting Mower Deck
Check the tire pressure before adjustment of the mower deck. See “Checking Tire Pressure” in
Maintenance section.
Faulty mower deck adjustments will cause an uneven mowing result.
WARNING!
Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.
Front Lift Arm
Chain
Rear Lift Arm
Chain
Leveling Mower Deck
Adjust the deck while the mower is on a level surface.
Make sure the tires are inflated to the correct pressure.
See “Technical Data” under Transmission. If tires are under or over inflated, you cannot properly adjust your deck.
Four slots control the height and pitch of the mower deck. The deck should be adjusted slightly higher in the rear.
Side-to-side adjustment
• Raise the deck into the four inch 4" (102 mm) cutting position.
•
•
Measure height from the bottom edge of the deck to the ground at both front corners.
3
Distance “A” should be the same, or within
/
16
" (5 mm) of an inch.
If adjustment is necessary, make adjustment to one side of the deck only. To adjust, loosen the locknut and move the mounting bolt up or down in the slot until both sideto-side measurements are equal. Recheck measurements after adjustment.
Mounting Bolt
Slotted Deck
Hanger Plates
Mounting Bolt
Front-to-back adjustment
To obtain the best cutting performance, the deck should be adjusted so the front tip of the blades are approximately
1
/
8
" (3.2 mm) to ¼" (6.5 mm) lower than the rear tip. If the front tip is higher, a poor quality cut will result.
Check blade height with blade facing front to rear.
Measure distance “B” at the front and rear tip of the blade.
Before making any necessary adjustments, check to make sure that the deck is level side-to-side. See
“Side to Side Adjustment” in Maintenance section.
With the deck in the 4" (100 mm) cutting position, measure the front and rear tip of each blade while facing front to rear.
To adjust, loosen the jam nut on the yoke, remove the securing ring and push the clevis pin out while supporting the deck. To lower that specific corner, lengthen the rod assembly by turning the yoke counter clockwise. To raise that specific corner, shorten the rod assembly by turning the yoke clockwise.
Reinstall clevis pin and recheck dimension.
Once front to back adjustment is correct, reinstall securing rings and secure jam nuts.
DIXON
-45
MAINTENANCE
Caster Wheels
Check every 200 hours. Lift front of unit off of ground so caster wheels can rotate freely. Tighten caster bolt then back off ½ turn. Check that wheel rotates freely. If wheel does not rotate freely back the caster bolt off in
¼ turn increments until wheel rotates freely.
Foam filled tires or solid tires will void the warranty.
IMPORTANT INFORMATION
DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures.
Only use O.E.M. specified tires.
Hardware
Check daily. Inspect the entire machine for loose or missing hardware.
1. Nut
2. Bolt
3. Sleeve
Caster wheels
1
Cleaning
Regular cleaning and washing, especially under the mower deck, will increase the machine’s lifespan.
Make it a habit to clean the machine directly after use
(after it is cooled), before the dirt sticks.
Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck.
Regulary clean deck and underside of deck, avoid spraying engine and electrical components with water.
Do not rinse hot surfaces with cold water. Let unit cool before washing.
Use protective glasses when cleaning and washing.
Cleaning
3
2
8050-092
46-
DIXON
MAINTENANCE
Tracking Adjustment
If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (1 bar). If the unit will not track straight, follow the steps below. Tracking must be checked on a flat and level concrete or blacktop surface.
Mower is tracking to the right.
Increase the air pressure 2-3 psi (0.1-0.2 bar) in the right rear tire or decrease the air pressure 2/3 psi in the left rear tire.
Mower is tracking to the left.
Increase the air pressure 2-3 psi (0.1-0.2 bar) in the left rear tire or decrease the air pressure 2/3 psi in the right rear tire.
Recheck tracking and keep making adjustments with the tire pressure until the unit tracks straight.
DO NOT exceed maximum recommended tire pressure 24 psi (1.6 bar).
Record the tire pressure for future reference.
Anti-scalp Rollers
Deck has anti-scalp rollers.
Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Antiscalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions.
IMPORTANT INFORMATION
Adjust anti-scalp rollers with the mower on a flat level surface.
1.
2.
3.
4.
5.
6.
Adjust the deck to the desired cutting height (see
“To Adjust Deck Cutting Height” in the operation section of this manual).
Using a ¾" wrench and a
9
/
16
" wrench, remove the nut and shoulder bolt from the anti-scalp roller.
Lower the anti-scalp roller to the ground, and raise it up to the next highest hole.
Replace and tighten the nut and shoulder bolt.
Be sure to adjust all of the anti-scalp rollers to the same position.
Be sure to readjust the anti-scalp rollers if the cutting height is changed.
EZT Transaxle
Purging Procedure
Due to the effects air has on efficiency in hydrostatic drives, it is critical that it is purged from the system.
Purge procedures should be done any time a hydrostatic system has been opened for maintenance or for adding oil to the system.
Symptoms in hydrostatic systems may be:
1.
2.
Noisy operation.
Lack of power or drive after short term operation.
3. High operation temperature.
Before starting, make sure the transaxle/transmission is at the proper oil level.
Procedures should be performed with the machine drive wheels off the ground, then repeated under normal operating conditions.
1. With the bypass valve open and the engine running, slowly move the directional control in both forward and.reverse directions (5 or 6 times). As air is purged, the oil level will drop.
2.
3.
With the bypass valve closed and the engine running, slowly move the directional control in both forward and reverse directions (5 to 6 times).
Check the oil level, and add oil as required after stopping the engine.
It may be necessary to repeat Steps 1 and 2 until all the air is completely purged from the system.
Purging is complete when the transaxle moves forward and in reverse at normal speed.
IMPORTANT INFORMATION
The anti-scalp rollers must not be used for gauge wheels or the roller and deck may be damaged.
DIXON
-47
Lubrication Schedule
LUBRICATION
8011-672-3
12/12 Every year
1/52 Every Week
1/365 Every day
Lubricate with grease gun
Oil change
Filter change
*Change transaxles (transmission) filters.
Lubricate with oil can
Level check
General
Remove the ignition key to prevent unintentional movements during lubrication.
When lubricating with an oil can, it must be filled with engine oil.
When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulfide grease.
For daily use, the machine should be lubricated twice weekly.
Wipe away excess grease after lubrication.
It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts.
48-
DIXON
LUBRICATION
Lubricating the Cables
If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a cable binds, it can disrupt operation.
If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to escape from the bottom.
Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.
Following the Lubrication Schedule
Front Wheel Mount
Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out.
Use only good quality bearing grease.
Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality.
Front Wheel Bearings
Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out.
Use only good quality bearing grease.
Deck Spindle
Lower the cutting deck completely.
If you use grease gun without rubber hose, the foot plate must be removed.
Lubricate with a grease gun, one zerk, 2-3 strokes.
Use only good quality bearing grease.
Lubricating the front wheels
8011-731
8011-732
IMPORTANT INFORMATION
Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces.
Deck spindle
DIXON
-49
LUBRICATION
Deck Outer Spindle
Lubricate using a grease gun, one zerk, each side 2-3 strokes.
Use only good quality bearing grease.
Engine Oil
Changing the Engine Oil
The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it should be changed every 50 hours.
Deck outer spindle
WARNING!
Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first.
8011-733
IMPORTANT INFORMATION
Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.
Avoid skin contact; wash with soap and water in case of spills.
1.
2.
3.
4.
5.
6.
7.
8.
Place the machine on a flat surface.
Place a container under the engine where the hose from the oil drain valve exits.
Remove the dipstick and open the drain valve.
Allow the oil to run out into the container.
Then close the oil drain valve.
Replace the oil filter if necessary.
Fill with new engine oil in accordance with
Checking the Oil Level.
Start the engine. Run it for a few seconds. Stop and re-check the oil level.
8011-730
Oil drain valve
50-
DIXON
LUBRICATION
Oil Level
Check the oil level in the engine when the machine is standing level and the engine is stopped.
Remove the dipstick, wipe it clean, and then replace it.
The dipstick should be screwed into place.
Take the dipstick out again and read the oil level.
API class SF, SG, SH, SJ or higher must be used.
Syntetic oil SAE 5W-30 or 10W-30 is recommended at all temperatures. Mineral oil SAE 5W-30, 10W-30 can be used between
-18 °C/0 °F and +5 °C/40 °F. At temperature above +5
°C/40 °F single grade SAE 30 must be used.
The engine holds 0.88 qt (1.0 liters) of oil excluding the filter, including filter 2 qt
(1.9 liters).
Remove the dipstick
The oil level should lie between the markings on the dipstick. If the level is approaching the “ADD” mark, fill the oil to the “FULL” mark on the dipstick.
Never fill to above the “FULL” mark.
The oil is filled through the hole for the dipstick.
The dipstick markings
Oil Filter
1. Drain the engine oil in accordance with the work description under the heading Engine Oil/Change
Engine Oil.
2.
3.
4.
Remove the oil filter. If necessary, use a filter remover.
Wipe new, clean engine oil onto the seal for the new filter.
Mount the filter by hand with + 3/4 turn.
5.
6.
Run the engine warm, then check that there are no leaks around the oil filter seal.
Check the oil level in the engine, fill if necessary.
The oil filter holds 0.1 qt (0.1 liters) of oil.
Changing the oil filter
8011-500
8009-159
8011-734
DIXON
-51
Problem
The engine will not start.
The engine runs rough.
TROUBLE SHOOTING
The starter does not turn the engine over.
•
•
•
•
•
•
•
•
Cause
Blade switch is engaged.
Ssteering controls are not locked in the neutral position.
Driver is not sitting in the driver’s seat.
Parking brake is not activated.
Battery is dead.
Contamination in the carburetor or fuel line.
Fuel supply is closed or the shut-off valve for the fuel tank is in the wrong position.
Clogged fuel filter or fuel line.
•
•
•
•
•
Dead battery.
Poor contacts on the battery terminal cable connections.
Fuse blown.
Ignition system faulty.
Fault in the starter safety circuit.
See Checking the Safety System in the
“Maintenance Section,”
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Faulty carburetor.
Choke control is pulled out with a warm engine.
Defective valves.
Defective piston, cylinder, piston ring, or cylinder head seal.
Cylinder head bolts are loose.
Clogged fuel filter or jet.
Clogged ventilation valve on the fuel cap.
Fuel tank nearly empty.
Defective spark plugs.
Spark plugs are loose.
Defective ignition cable.
Defective spark plug electrode.
Defective spark plug connection.
Rich fuel mixture or fuel-air mixture.
Wrong fuel type.
Water in the fuel.
Clogged air filter.
Air trapped in hydraulic system.
52-
DIXON
TROUBLE SHOOTING
Problem
The engine seems weak.
The engine overheats.
Battery not charging.
The machine moves slowly, unevenly, or not at all.
Mower deck not engaging.
Transaxle leaks oil.
•
•
•
•
Cause
Clogged air filter.
Defective spark plugs.
Carburetor incorrectly adjusted.
Air trapped in hydraulic system.
•
•
•
•
•
•
•
•
•
Clogged air intake or cooling fins.
Engine overloaded.
Poor ventilation around engine.
Defective engine speed regulator.
Soot in the combustion chamber.
Too little or no oil in the engine.
Defective spark plugs.
Pre-ignition incorrect.
Air trapped in hydraulic system.
• Poor contact with battery terminal cable connectors.
•
•
•
•
Parking brake on.
Bypass valve on pump open.
Drive belt for the transmission gears slack or has come off.
Air trapped in hydraulic system.
•
•
•
•
Drive belt for the mower deck has come loose.
Contact for the electromagnetic coupling has loosened.
The blade switch is faulty or has come loose, from the cable contact.
The fuse has blown.
•
•
Damaged seals, housing, or gaskets.
Air trapped in hydraulic system.
DIXON
-53
Problem
Uneven mowing results.
The machine vibrates.
TROUBLE SHOOTING
Cause
•
•
•
•
•
•
•
• Different air pressure in tires on left and right sides.
Bent blades.
Suspension for the mower deck is uneven.
Chain fixture has come loose.
Blades are dull.
Driving speed too high.
Grass is too long.
Grass collected under the mower deck.
•
•
•
The blades are loose.
The blades are incorrectly balanced.
The engine is loose.
54-
DIXON
STORAGE
Winter Storage
At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.
Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage.
Add stabilizer to the fuel in the tank or in the storage container. Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the carburetor. Do not empty the fuel tank and the carburetor if you have added stabilizer
WARNING!
Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes drier, etc. Handle the fuel with care. It is very flammable and can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and far away from open flame. Never use gasoline for cleaning. Use a degreaser and warm water instead.
To ready the machine for storage, follow these steps:
1.
2.
3.
4.
Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion.
Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose.
Change the engine oil; dispose of properly.
Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor.
5.
6.
7.
8.
Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug.
Lubricate all grease zerks, joints, and axles.
Remove the battery. Clean, charge, and store the battery in a cool place, but protect it from direct cold.
Store the machine in a clean, dry place and cover it for extra protection.
Service
When ordering spare parts, please specify the purchase year, model, type, and serial number.
Always use genuine Dixon spare parts.
An annual check-up at an authorized service workshop is a good way to ensure that your machine performs its best the following season.
DIXON
-55
TO RH BRAKE
SWITCH
Y Y G
SCHEMATIC
GROUND
W
W
TO SOLENOID
Y
R
TO ALT.
R
W/G
TO LH BRAKE
SWITCH
TO ENGINE SHUT
OFF
G
R/W
G
TO ELECTRIC
CLUTCH
B
W
W/G
G
TO CIRCUIT
BREAKER
R R
TO CLUTCH
SWITCH
R/W
TO IGNITION
SWITCH
Y
W/G
W/G
G
B
Y
R/W
R
R
G
G
W
W
TO RH
LEVER
W/G
W/G
W
W
TO SEAT
SWITCH
COLOR CODE
R - RED
R/W - RED W/WHITE STRIPE
G - GREEN
W/G - WHITE W/GREEN STRIPE
Y - YELLOW
B - BLUE
W - WHITE
56-
DIXON
W
W
W/G
Y Y
TO LH
LEVER
TECHNICAL DATA
Accessories
BioClip attachment (Mulch kit)
Collection system
Torque Specifications
Engine crankshaft bolt
Deck pulley bolts
Lug nuts
Blade bolt
Standard ¼" fasteners
50 ft/lb (67 Nm)
45 ft/lb (61 Nm)
75 ft/lb (100 Nm)
45-55 ft/lb (60-75 Nm)
9 ft/lb (12 Nm)
Standard
5
/
16
" fasteners
Standard
3
/
8
" fasteners
Standard
7
/
16
" fasteners
Standard ½" fasteners
18 ft/lb (25 Nm)
33 ft/lb (44 Nm)
52 ft/lb (70 Nm)
80 ft/lb (110 Nm)
When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling.
In order to implement improvements, specifications and designs can be altered without prior notification.
Note that no legal demands can be placed based on the information contained in these instructions.
Use only original parts for repairs. The use of other parts voids the warranty.
Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit.
DIXON
-57
TECHNICAL DATA
ZTR 44 / 968999538 ZTR 36 / 968999539
Engine
Manufacturer
Type
Power
Lubrication
Oil capacity excluding filter
Oil capacity including filter
Engine oil, Synthetic
Engine oil, Mineral Class
Fuel
Fuel tank capacity
Spark plugs/gap
Cooling
Air filter
Alternator
Starter
Transmission
Type
Air cooling
Standard
12V 16A
Electric 12V
Speed and direction controls
Speed forward
Speed reverse
Brakes
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
Front caster tires, smooth tread 11 x 4-5, 4 ply
Rear tires, turf pneumatic 18 x 9.5-8
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar
*As rated by the engine manufacturer
Kohler
Courage
20 hp*
Pressure with oil filter
1.6 qt (1.5 liters)
SAE 10W30
API, SJ, SH, SG
Min 87 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
Champion RC124C
030” / 0.75 mm
Briggs & Stratton
Intek
16 hp*
Pressure with oil filte
1.3 qt (1.3 liters)
SAE 5W30, 10W30
SAE 30, (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane unleaded
(Max methanol 5%, max ethanol
10%, Max MTBE 15%
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Air cooling
Standard
12V 16A
Electric 12V
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
11 x 4-5, 4 ply
18 x 9.5-8
15 PSI / 103 kPa / 1 bar
58-
DIXON
ajkfas sajkfdaslfd askjfasfdj afdajsaf
Equipment
Cutting width
Cutting height
Uncut circle
Number of blades
Blade length
Nose rollers
Michigan seat
Hinged armrests
Hour meter
Blade engagement
Deck construction
Productivity
Output
Overall dimensions
Weight
Base machine length
Base machine width
Base machine height
Overall width, chute up
Overall width, chute down
TECHNICAL DATA
ZTR 44 / 968999538 ZTR 36 / 968999539
44"
1.5" - 4.5"
0
3
14.97"
Yes
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
36"
1.5" - 4.5"
0
2
18.5"
Yes
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
3.1 acres / hr
590 lbs
70.5"
44.5"
43.25"
46.25"
58"
2.55 acres / hr
538 lbs
70.5"
40"
43.25"
40.5"
51"
DIXON
-59
TECHNICAL DATA
ZTR 36 / 968999609
Engine
Manufacturer
Type
Power
Lubrication
Oil capacity excluding filter
Oil capacity including filter
Engine oil, Synthetic
Engine oil, Mineral Class
Fuel
Fuel tank capacity
Spark plugs/gap
Briggs & Stratton
Intek
16 hp*
Pressure with oil filter
1.3 qt (1.31 liters)
1.5 qt (1.42 liters)
SAE 5W30, 10W30
SAE 30 (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Cooling
Air filter
Alternator
Starter
Transmission
Type
Air cooling
Standard
12V 16A
Electric 12V
Speed and direction controls
Speed forward
Speed reverse
Brakes
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
Front caster tires, smooth tread 11 x 4-5, 4 ply
Rear tires, turf pneumatic 18 x 7.5-8
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar
ZTR 44 / 968999611
Briggs & Stratton
ELS
22 hp*
Pressure with oil filte
1.875 qts (1.8 liters
2 qt (1.91 liters)
SAE 5W30, 10W30
SAE 30, (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Air cooling
Standard
12V 16A
Electric 12V
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
11 x 4-5, 4 ply
18 x 9.5-8
15 PSI / 103 kPa / 1 bar
*As rated by the engine manufacturer
60-
DIXON
Equipment
Cutting width
Cutting height
Uncut circle
Number of blades
Blade length
Nose rollers
Michigan seat
Hinged armrests
Hour meter
Blade engagement
Deck construction
Productivity
Output
Overall dimensions
Weight
Base machine length
Base machine width
Base machine height
Overall width, chute up
Overall width, chute down
TECHNICAL DATA
ZTR 36 / 968999609 ZTR 44 / 968999611
36"
1.5" - 4.5"
0
2
18.5"
Yes
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
44"
1.5" - 4.5"
0
3
14.97"
Yes
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
2.55 acres / hr
538 lbs
70.5"
40"
43.25"
40.5"
51"
3.1 acres / hr
590 lbs
70.5"
44.5"
43.25"
46.25"
58"
DIXON
-61
TECHNICAL DATA
ZTR 42 / 968999689
Engine
Manufacturer
Type
Power
Lubrication
Oil capacity excluding filter
Oil capacity including filter
Engine oil, Synthetic
Engine oil, Mineral Class
Fuel
Fuel tank capacity
Spark plugs/gap
Briggs & Stratton
Intek
19 hp*
Pressure with oil filter
1.3 qt (1.31 liters)
1.5 qt (1.42 liters)
SAE 5W30, 10W30
SAE 30 (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Cooling
Air filter
Alternator
Starter
Transmission
Type
Air cooling
Standard
12V 16A
Electric 12V
Speed and direction controls
Speed forward
Speed reverse
Brakes
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
Front caster tires, smooth tread 11 x 4-5, 4 ply
Rear tires, turf pneumatic 18 x 7.5-8
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar
ZTR 42 / 968999713
Briggs & Stratton
ELS
19 hp*
Pressure with oil filte
1.875 qts (1.8 liters
2 qt (1.91 liters)
SAE 5W30, 10W30
SAE 30, (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Air cooling
Standard
12V 16A
Electric 12V
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
11 x 4-5, 4 ply
18 x 9.5-8
15 PSI / 103 kPa / 1 bar
*As rated by the engine manufacturer
62-
DIXON
Equipment
Cutting width
Cutting height
Uncut circle
Number of blades
Blade length
Nose rollers
Michigan seat
Hinged armrests
Hour meter
Blade engagement
Deck construction
Productivity
Output
Overall dimensions
Weight
Base machine length
Base machine width
Base machine height
Overall width, chute up
Overall width, chute down
TECHNICAL DATA
ZTR 42 / 968999689 ZTR 42 / 968999713
42"
1.5" - 4.5"
0
2
21"
No
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
42"
1.5" - 4.5"
0
2
21"
No
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
2.97 acres / hr
530 lbs
70.5
42.5"
43.25"
43.5"
48.25"
2.97 acres / hr
530 lbs
70.5
42.5"
43.25"
43.5"
48.25"
DIXON
-63
TECHNICAL DATA
ZTR 44 / 968999547
Engine
Manufacturer
Type
Power
Lubrication
Oil capacity excluding filter
Oil capacity including filter
Engine oil, Synthetic
Engine oil, Mineral Class
Fuel
Fuel tank capacity
Spark plugs/gap
Briggs & Stratton
ELS
22 hp*
Pressure with oil filte
1.875 qts (1.8 liters
2 qt (1.91 liters)
SAE 5W30, 10W30
SAE 30, (winter 10W30)
API, SF, SJ, SH, SG
Min 86 octane, unleaded (Max methanol 10%, max MTBE 15%)
4.5 gallon (17 liters)
NGK - BPR4ES
.030” / 0.75 mm
Cooling
Air filter
Alternator
Starter
Transmission
Type
Air cooling
Standard
12V 16A
Electric 12V
Speed and direction controls
Speed forward
Speed reverse
Brakes
EZT2200 Hydro-Gear
Dual levers, foam gripped
7mph
6mph
Mechanical parking brake
Front caster tires, smooth tread 11 x 4-5, 4 ply
Rear tires, turf pneumatic 18 x 9.5-8
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar
64-
DIXON
Equipment
Cutting width
Cutting height
Uncut circle
Number of blades
Blade length
Nose rollers
Michigan seat
Hinged armrests
Hour meter
Blade engagement
Deck construction
Productivity
Output
Overall dimensions
Weight
Base machine length
Base machine width
Base machine height
Overall width, chute up
Overall width, chute down
TECHNICAL DATA
ZTR 44 / 968999611
44"
1.5" - 4.5"
0
3
14.97"
Yes
Standard
Yes
Standard
Electric clutch
11 gauge w/10 gauge skirts
3.1 acres / hr
590 lbs
70.5"
44.5"
43.25"
46.25"
58"
DIXON
-65
CONFORMITY CERTIFICATES
USA Requirements
Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels.
Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents.
66-
DIXON
SERVICE JOURNAL
Action
Delivery Service
1. Charge the battery.
5.
6.
7.
8.
2.
3.
Adjust the tire pressure of all wheels to 15 PSI (1 bar).
Mount the steering controls in the normal position.
4. Connect the contact box to the cable for the seat’s safety switch.
Check that the right amount of oil is in the engine.
Adjust the position of the steering controls.
Fill with fuel and open the fuel shut off valve.
Start the engine.
9. Check that there is drive to both wheels.
10. Check the mower deck adjustment.
11. Check:
The safety switch for the parking brake.
The safety switch for the mower deck.
The safety switch in the seat.
The safety switch in the steering controls.
Parking brake functionality.
Driving forward.
Driving backward.
Engaging the blades.
12. Check the idle speed
13. Check the engine high idle speed
14. Inform the customer about:
The need and advantages of following the service schedule.
The need and advantages of leaving the machine for service every 300 hours.
The effects of service and maintaining a service journal on the machine’s resale value.
Application areas for Mulching.
15. Fill in the sales papers, etc.
Date, mtr reading, stamp, sign
Delivery service has been carried out.
No remaining notes.
Certified:
DIXON
-67
Action
After the First 5-8 Hours
1. Change engine oil.
SERVICE JOURNAL
Date, mtr reading, stamp, sign
68-
DIXON
SERVICE JOURNAL
Action
25-Hour Service
1. Check the fuel pump’s air filter.
2. Sharpen/Replace mower blades if required.
3. Check the tire pressures.
4. Check battery with cables.
5. Lubricate according to lubrication chart.
6. Check/clean the engine’s cooling air intake.
7. Clean the air cleaner’s pre-filter (foam).
Date, mtr reading, stamp, sign
DIXON
-69
SERVICE JOURNAL
Action
50-Hour Service
1. Perform the 25-hour service.
2. Clean/replace the air cleaner’s filter cartridge (paper filter)
(shorter intervals for dusty operating conditions).
3. Change engine oil.
4. Lubricate according to lubrication chart.
5. Check/adjust the parking brake.
Date, mtr reading, stamp, sign
70-
DIXON
SERVICE JOURNAL
Action
100-Hour Service
1. Perform the 25-hour service.
2. Perform the 50-hour service.
3. Change the engine oil filter.
4. Clean/replace the spark plugs.
5. Replace the fuel filter.
6. Clean the cooling fins on the engine and transmission.
7. Check V-belts.
8. Check tighten caster wheel axle bolts (every 200 hours).
9. Change the air filter’s paper cartridge.
Date, mtr reading, stamp, sign
DIXON
-71
SERVICE JOURNAL
Action
300-Hour Service
1. Inspect the machine. Come to agreement with the customer as to which additional work is to be carried out.
2. Perform the 25-hour service.
3. Perform the 50-hour service.
4. Perform the 100-hour service.
5. Check/adjust the mower deck.
6. Clean the combustion chamber and grind the valve seats.
7. Check the engine valve clearance.
8. Replace the air cleaner’s pre-filter (foam).
Date, mtr reading, stamp, sign
72-
DIXON
SERVICE JOURNAL
Action
At Least Once Each Year
1. Clean the engine’s cooling air intake (25 hours).
2. Replace the air cleaner’s pre-filter (foam) (300 hours).
3. Replace the air filter’s paper cartridge.
4. Change the engine oil (50 hours).
5. Replace the engine oil filter (100 hours).
6. Check/adjust the cutting height.
7. Check/adjust the parking brake (50 hours).
8. Clean/Change the spark plugs (100 hours).
9. Change the fuel filter (100 hours).
10. Clean the cooling fins (100 hours).
11. Check the engine valve clearance.
12. Perform the 300-hour service at an authorized service workshop.
Date, mtr reading, stamp, sign
DIXON
-73
Action
SERVICE JOURNAL
Date, mtr reading, stamp, sign
74-
DIXON
Action
SERVICE JOURNAL
Date, mtr reading, stamp, sign
DIXON
-75
Action
SERVICE JOURNAL
Date, mtr reading, stamp, sign
76-
DIXON
Action
SERVICE JOURNAL
Date, mtr reading, stamp, sign
DIXON
-77
P/N 539 131911 R01
® ®
07/20/08
Letöltés
A nyilvános link frissítve
A csevegés nyilvános linkje frissítve lett. You may view and manage your chat links after registration here.
Dokumentum nyilvános linkje
Hirdetés
