Owner`s manual | DKS Enterprises 1802 Telephone User Manual

Owner’s Manual
1802, 1803, 1808, 1810
Telephone Entry Systems
DoorKing, Inc.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
www.doorking.com
P/N 1800-060 REV D, 7/01
Copyright 2001 DoorKing, Inc. All rights reserved.
2
Use this manual with the following models only.
All 1802, 1803, 1808 and 1810 Telephone Entry Systems with circuit board 1862-010, Rev A or
higher.
DoorKing, Inc. reserves the right to make changes in the products described in this manual
without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions
or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to
this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be
copied, reproduced, translated, or reduced to any electronic medium without prior written consent
from DoorKing, Inc.
3
TABLE OF CONTENTS
Preface
Important Notices................................................................................................................................................. 6
General Information ............................................................................................................................................. 7
Features ............................................................................................................................................................. 8
Section 1 – Installation
1.1
Installation Guidelines – All Systems ............................................................................................... 9
1.1.1
Surface 1803 and 1810 Mount Units..................................................................................... 10
1.1.2
Surface Mount 1803 and 1810 Units with Recess Box.......................................................... 11
1.1.3
Flush Mount 1803 and 1810 Units ........................................................................................ 12
1.1.4
Flush Mount Rough-in Box (1803 and 1810 only) ................................................................. 13
1.1.5
Flush Mount Trim Ring (1803 and 1810 only0 ...................................................................... 14
1.1.6
Flush Mount Surface Mounting Kit (1803 and 1810 only)...................................................... 15
1.1.7
1802 Surface Mount ............................................................................................................. 16
1.1.8
1808 Surface Mount ............................................................................................................. 17
1.2
Memory Chip Installation ................................................................................................................... 18
1.3
Postal Lock Installation ..................................................................................................................... 19
Section 2 – Wiring
General Information ........................................................................................................................................... 21
Maximum Wire Run Distance Charts ................................................................................................................ 22
2.1
Main Terminal Description................................................................................................................. 23
2.2
Wiring Description ............................................................................................................................. 24
2.3
Relay Wiring (Typical)
2.3.1
Controlling a Single Door or Gate ......................................................................................... 25
2.3.2
Controlling a Gate and a Pedestrian Gate or Door................................................................ 26
Section 3 – Programming
General Information ........................................................................................................................................... 27
3.1
3.2
General Programming
3.1.1
Master Code ......................................................................................................................... 28
3.1.2
Single or Multiple Systems ................................................................................................... 28
3.1.3
Relay Strike Time ................................................................................................................. 28
3.1.4
Talk Time ............................................................................................................................. 29
3.1.5
Tone Open Numbers ............................................................................................................ 29
3.1.6
Postal Switch........................................................................................................................ 30
3.1.7
Touch-tone / Rotary-dial ....................................................................................................... 30
3.1.8
Keypad Function................................................................................................................... 31
3.1.9
Star (*) Key Function ............................................................................................................ 31
Phone Number Programming
3.2.1
Directory Code Length.......................................................................................................... 32
3.2.2
7-Digit Phone Numbers ........................................................................................................ 32
3.2.3
Area Codes .......................................................................................................................... 33
3.2.4
Phone Numbers with Area Code Reference ......................................................................... 33
3.2.5
Deleting Individual Phone Numbers...................................................................................... 33
3.2.6
Delete All Phone Numbers ................................................................................................... 34
3.2.7
Display / Delete Phone Numbers.......................................................................................... 34
3.2.8
Display Phone Numbers with Known Directory Code............................................................ 34
4
3.3
3.4
Entry Code Programming
3.3.1
Four-Digit Entry Code Programming ..................................................................................... 35
3.3.2
Delete Individual Four-Digit Entry Codes .............................................................................. 35
3.3.3
Delete All Four-Digit Entry Codes ......................................................................................... 35
3.3.4
Four-Digit Entry Code Divide Number................................................................................... 35
3.3.5
Five-Digit Entry Code Programming ..................................................................................... 36
3.3.6
Delete Individual Five-Digit Entry Codes ............................................................................... 36
3.3.7
Delete All Five-Digit Entry Codes.......................................................................................... 36
3.3.8
Five-Digit Entry Code Divide Number ................................................................................... 36
Time Functions Programming
3.4.1
Time Clock Programming ..................................................................................................... 37
3.4.2
Automatic Relay Activation Time Zones ............................................................................... 37
3.4.3
Four-Digit Entry Code Time Zone ......................................................................................... 38
3.4.4
Five-Digit Entry Code Time Zone.......................................................................................... 38
3.4.5
Flash Entry Codes ................................................................................................................ 39
Section 4 – Adjustments
4.1
Speaker Volume................................................................................................................................... 41
4.2
Feedback ............................................................................................................................................. 41
4.3
Click Sensitivity .................................................................................................................................... 41
4.4
Display Contrast (1802, 1803, 1810 only) ............................................................................................. 41
4.5
Master Code Switch ............................................................................................................................. 42
4.6
Ring Pin................................................................................................................................................ 42
4.7
Handset / Hands Free .......................................................................................................................... 42
Section 5 – Operating Instructions
5.1
5.2
5.3
General Instructions
5.1.1
Guest Instructions................................................................................................................. 43
5.1.2
Responding to a Guest Call .................................................................................................. 43
5.1.3
Using Entry Codes................................................................................................................ 43
System Administrator
5.2.1
Remote Programming........................................................................................................... 44
5.2.2
Remote Relay Activation ...................................................................................................... 44
5.2.3
Relay Check ......................................................................................................................... 44
5.2.4
Entry Code Time Zone Enable / Disable ............................................................................... 45
5.2.5
Auto Relay Activation Time Zone Enable / Disable ............................................................... 45
Miscellaneous Operating Instructions
5.3.1
Switch Input Operation ......................................................................................................... 46
5.3.2
Talk Time.............................................................................................................................. 46
5.3.3
Line Sharing ......................................................................................................................... 46
5.3.4
Connection to a PBX ............................................................................................................ 47
5.3.5
10-digit Dialing...................................................................................................................... 47
Section 6 – Maintenance and Trouble Shooting
6.1
Trouble Shooting .................................................................................................................................. 49
6.2
Accessories.......................................................................................................................................... 51
6.3
Log Tables ........................................................................................................................................... 52
5
IMPORTANT NOTICE
FCC - UNITED STATES
This equipment has been tested and found to comply with the limits for a class A digital device,
pursuant to Part 15 of the FCC Rules and Regulations. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Registration Number: DUF6VT-12874-OT-T
DOC - CANADA
The Canadian Department of Communications label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective, operational, and
safety requirements. The Department does not guarantee the equipment will operate to the users
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable means of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections of the power
utility, telephone lines, and internal metallic water pipe system, if present, are connected together.
This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
DOC Registration Number: 1736 4528 A
Notice:
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to
be connected to a telephone loop which is used by the device, to prevent overloading. The
termination on a loop may consist of any combination of devices subject only to the requirement that
the sum of the load numbers of all the devices does not exceed 100.
Notice:
DoorKing does not provide a power transformer on units sold into Canada. Use only transformers that
are CSA listed to power the telephone entry system. 1802, 1803, 1808, 1810, 1814, 1815, 1818 and
all "P" series systems require a 16.5-volt, 20 VA transformer. The models 1816 and 1817 require a
16.5-volt, 40 VA transformer. The model 1812 requires a 24-volt, 20 VA transformer.
Listing:
This product has been tested to and found to be in compliance with the U.L 294 Safety Standard by
Intertek Testing Services NA Inc. (a Nationally Recognized Testing Laboratory) and is ETL listed.
6
GENERAL INFORMATION
•
Prior to beginning the installation of the telephone entry system, we suggest that you become
familiar with the instructions, illustrations, and wiring guidelines in this manual. This will help
insure that you installation is performed in an efficient and professional manner.
•
The proper installation of the telephone entry panel is an extremely important and integral
part of the overall access control system. Check all local building ordinances and building
codes prior to installing this system. Be sure your installation is in compliance with local
codes.
•
When used to control a door or pedestrian gate, try to locate the telephone entry system as
near as possible to the entry point. The unit should be mounted on a rigid wall to prevent
excessive shock and vibration from closing doors or gates. Continuous vibration and shock
from slamming doors or spring-loaded pedestrian gates will damage the circuit board. Under
no circumstances should the unit be mounted directly to a moving door or gate.
•
ADA mounting requirements for door control. The mounting of the unit shall be in such a
way that the LCD display is positioned so that it is readily visible to and usable by a person
sitting in a wheelchair with an approximate eye level of 45 inches and shall comply with the
following requirements:
1. If mounted vertically or tipped no more than 30 degrees away from the viewer, the
center line of the LCD shall be located a maximum of 52 inches above grade.
2. If the clear floor space allows only forward approach to the system, the maximum
high forward reach allowed is 48 inches above grade to the top of the keypad.
3. If the high forward reach to the system is over an obstruction of greater than 20
inches but less than 25 inches, the maximum high forward reach allowed is 44 inches
above grade to the top of the keypad.
4. If the clear floor space allows parallel approach by a person in a wheelchair, the
maximum high side reach shall be 54 inches above grade to the top of the keypad.
5. If the high side reach is over an obstruction of 24 inches or less, the maximum high
side reach allowed is 46 inches above grade to the top of the keypad.
•
When used to control a vehicular gate with an automatic gate operator, the telephone
entry system must be mounted a minimum of ten (10) feet away from the gate and gate
operator, or in such a way that a person cannot operate the entry system and/or touch
the gate or gate operator at the same time.
•
Be sure that the system is installed so that it is not directly in the traffic lane. Goose neck
mounting post and kiosks work well for these type systems. When planning where to locate
the system, take into consideration traffic lane layouts, turn around lanes for rejected access,
conduit runs, power availability, etc.
•
Environmental factors must also be taken into account. Surface mount units are designed for
direct outdoor installations, however it is preferable to protect them from direct exposure to
driven rain or snow whenever possible. Flush mount and wall mount units must be protected
from direct exposure to the elements. Be sure that ample lighting is provided so that guest
can read both the directory and the operating instructions at night.
•
This telephone entry system contains a number of static sensitive components that can be
damaged or destroyed by static discharges during installation or use. Discharge any static
prior to removing the circuit board from the lobby panel by touching a proper ground device.
7
FEATURES
•
Can provide service for up to 1000 residents.
•
System can be programmed from the front keypad or remotely using a touch-tone telephone.
•
System keypad will emit DTMF tones after a call is answered allowing the system to be used
with auto-attendants, answering machines, etc.
•
Directory codes can be set from 1 to 4 digits in length and can be randomly assigned.
•
10 programmable area codes allow the system to be used in areas requiring 10 and 11-digit
dialing.
•
Two internal relays allow the system to control a main entry point plus an additional entry
point.
•
Built in time clock provides hold open time zones, entry code time zones and “Flash” entry
codes.
•
5-digit entry codes available for special needs.
•
Programmable switch inputs can be set to activate a relay or to dial a preprogrammed phone
number.
8
SECTION 1 - INSTALLATION
Order your telephone line at least two weeks prior to the planned installation date. This will assure
that a phone line is available when the unit is installed. The telephone company will require the
following information from you:
Type:
Ringer Equivalence:
Jack Type:
FCC Registration (US):
DOC (Canada):
Electrical Listing:
Touch Tone, Loop Start
0.0 A
RJ11C
DUF6VT-12874-OT-T
1736 4528 A
Complies with U.L. 294 - ETL Listed
CALLER ID: You may want to consider ordering caller ID blocking from the telephone company for
the entry system phone line. Without caller ID blocking, tenants with the proper phone equipment will
be able to identify the telephone number that the entry system is installed on. This may or may not
be desirable.
1.1 INSTALLATION GUIDELINES – ALL SYSTEMS
1. Open the cabinet of the telephone entry system and disconnect the keypad ribbon cable
from the main circuit board.
2. Remove the 6-32 x 1/2 round head screws from the upper corners of the circuit board.
3. Remove the circuit board by gently pulling it out of the main terminal edge connector.
CAUTION - the circuit board contains static sensitive components. Discharge any static
electricity from your hands by touching a proper ground device before removing the
circuit board. Place the circuit board where it will not be damaged.
4. Mount the cabinet of the telephone entry system. Be sure that mounting screws do not
protrude into the cabinet where they could cause a short on the back of the circuit board.
Make any necessary conduit connections.
5. Route wiring into the cabinet. Do not apply any power at this time.
6. Clean out the cabinet. Be sure that all dirt, metal and/or wood debris is removed from the
cabinet and that the terminal strip edge connector is clean and free of any loose particles.
7. Re-install the circuit board into the cabinet by gently pushing the circuit board terminals
into the edge connector. CAUTION - the circuit board contains static sensitive
components. Discharge any static electricity from your hands by touching a proper
ground device before removing the circuit board.
8. Secure the circuit board to the cabinet using the screws removed in step 2.
9. Plug the keypad ribbon cable into the circuit board. The cable points down.
9
1.1.1 Surface Mount 1803 and 1810 Units
Surface mount units can be mounted directly to a wall or pilaster, or can be post mounted using a
DoorKing heavy-duty mounting post (p/n 1200-047 and 1200-048). Be sure the unit is mounted
securely and is not subject to vibration from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
4.75
9.0
.875
13.0
11.0
.25 DIA
.5
.875 DIA
2.625
3.25
5.625
11.25
1.625
2.5
.875 DIA
10
1.1.2 Surface Mount 1803 and 1810 Units with Recess Box
Surface mount units can be semi-flush mounted into a wall or pilaster by using the optional recessmounting box (p/n 1803-150). Be sure the unit is mounted securely and is not subject to vibration
from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
2.125
15.00
11.125
3.625
2.125
10-24 x 1.25 STUD
13.25
11.0
8.375
15.25
13.25
12.0
.25 DIA
4.875
2.25
3.375
.5
.25 DIA
2.0
1.375 DIA
1.06
1803-150
Recess Box
8.812
2.68
Surface Mount
Entry System
.25 DIA
.5
2.2
5.75
9.3
11.5
11
1.1.3 Flush Mount 1803 and 1810 Units
1.125
Flush mount units are installed into a wall with flush mount kits 1814-065 (stainless) or 1814-066
(gold). Flush mount kits are not included with the entry system. Flush mount units are not designed
for direct exposure to the weather. Be sure the unit is mounted securely and is not subject to
vibration from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
12.0
1.125
3.0
9.0
.875 DIA
2.625
.50
.875
2.625
5.625
1.625
11.25
.875 DIA
2.5
12
13.0
13.25
11.0
.25 DIA
1.1.4 Flush Mount Rough-in Box (applies to 1803 and 1810 only)
The flush mount installation kit has two parts; the rough-in box and the trim ring. The rough-in box is
installed first.
1.25
12.75
1.875
9.0
4.25
1.75
3.875
14.5
11.0
13.25
10.25
7.25
10-24 x 1.125 Stud
1.125 DIA
3.5
1.75
9.25
1.75
.25 DIA
1.75
6.375
11.0
13
1.1.5 Flush Mount Trim Ring (use with 1803 and 1810 units only)
Flush mount units can be mounted by using the 1814-065 (stainless) or 1814-066 (gold) mounting kit.
Flush mounting kits are not included with the unit. Flush mount units are not designed for direct
exposure to the weather. Be sure the unit is mounted securely and is not subject to vibration from
closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
14.25
2.625
9.0
2.25
3.625
13.625
16.0
11.0
.25 DIA
1.0
.875
1.25 DIA
3.0
Rough-in
Box
1.625
1.25 DIA
1.125
5.875
3.0
7.0
8.5
11.75
14
Trim
Ring
Flush Mount
Entry System
1.1.6 Flush Mount Surface Mounting Kit (use with 1803 and 1810 units only)
Flush mount units can be surface mounted by using the optional 1814-152 surface mount trim ring.
Flush mount units are not designed for direct exposure to the weather. Be sure that the unit is
securely mounted and is not subject to vibration from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
12.0
1.0
2.625
13.5
.375
6.0
1.125
.375
7.5
.875
9.0
3.0
1.125 DIA
1.125 SQ
1814-152
Trim Ring
15
Flush Mount
Entry System
1.1.7 1802 Surface Mount Only
Surface mount units can be mounted directly to a wall or pilaster, or can be post mounted using a
DoorKing mounting post (p/n 1200-045 and 1200-046). Be sure the unit is mounted securely and is
not subject to vibration from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
5.0
12
3.50
3.50
.875 D
.875 D
.875
1.75
3.375
6.50
1.75
.875 D
1.625
16
1.1.8 1808 Surface Mount Only
Surface mount units can be mounted directly to a wall or pilaster, or can be post mounted using a
DoorKing mounting post (p/n 1200-045 and 1200-046). Be sure the unit is mounted securely and is
not subject to vibration from closing doors or gates.
CAUTON! If this entry system is used to control a vehicular gate with an automatic gate operator, the
entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or
in such a way that a person cannot operate the entry system and touch the gate or gate operator at
the same time.
6.375
3.50
3.50
7.375
.875
3.375
3.0
2.625
.875
17
1.2 MEMORY CHIP INSTALLATION
The telephone entry system is shipped with a memory chip packaged in a separate box inside the
shipping container. The memory chip must be installed for the telephone entry system to operate.
CAUTION!! Do not install the memory chip with power to the telephone entry system turned
on. Attempting to install the memory chip with power on will irrevocably damage the chip.
CAUTION!! The memory chip is a static sensitive component. Discharge any static electricity
from your hands by touching a proper ground device before removing the control board.
Handle the memory chip with care.
1. The large memory chip socket is colored blue and is located on the right hand side of the
circuit board. Be sure that the handle is in the un-locked position (towards the left). Be
sure that power to the telephone entry system is off.
2. Carefully insert the memory chip into the socket. The small half circular indentation on
the chip must be at the top. CAUTION: Installing the memory chip upside down will
cause permanent damage to the chip. Be sure that the memory chip is seated correctly
in the socket.
3. Move the lever on the chip socket to the locked position (towards the right).
18
1.3 POSTAL LOCK INSTALLATION
At some locations, such as gated communities, it will be necessary to provide access to the mail
carrier so that they can deliver the mail. Mail carrier access will be provided by the installation of an
Arrow Postal Lock. This is the same lock that the Post Office uses for gang mailboxes. These locks
are not available to the public. The installer or the building owner/manager will have to call the Post
Office and arrange for the installation of this lock into the telephone entry system. The 1802, 1803
and 1810 units are all pre-wired to accept the installation of the postal lock.
The 1808 unit cannot accept the postal lock. If you are using the 1808 and need postal service
access, use the DoorKing Postal Lock Box (P/N 1402-080).
Prior to installation of the postal lock, be sure power to the telephone entry system is turned off.
1.
2.
3.
Remove the hole plug on the faceplate of the telephone entry system.
Cut the wire tie wrapped around the micro switch next to the postal lock access hole.
Remove the two hex nuts from the postal lock-mounting studs. Mount the postal lock
on the two studs and secure with the hex nuts.
When the lock is installed, check to be sure that the pawl of the lock, in its extended position, is
depressing the micro switch (the micro switch is wired normally closed). When the mail carrier inserts
his key and turns the postal lock, the pawl is withdrawn and the micro switch will activate the relay
that has been programmed for this function for the programmed strike time.
19
20
SECTION 2 – WIRING
Prior to installing wiring to the telephone entry system, we suggest that you become familiar with the
instructions, illustrations, and wiring guidelines in this manual. This will help insure that you
installation is performed in an efficient and professional manner.
The wiring of the telephone entry panel is an extremely important and integral part of the
overall access control system. Use proper wire for the communication line, power wires, and
be sure that the system is properly grounded. Check all local building ordinances and
building codes prior to installing this system. Be sure your installation is in compliance with
local codes.
If this telephone entry system is used to control a vehicular gate with an automatic gate
operator, the telephone entry system must be mounted a minimum of ten (10) feet away from
the gate and gate operator. If this unit has been installed closer to the automated vehicular
gate, do not proceed with any wiring until the unit has been moved and re-installed so that it is
in compliance with these instructions.
Use only the supplied transformers (or U.L. listed equivalent) to power the telephone entry system
(16.5 VAC, 20 VA). Do not power any other devices (electric strikes, magnetic locks, etc.) from this
power transformer. For wire runs up to 100 feet, use 18 AWG, 600 volt insulated wire. For wire runs
up to 200 feet, use 16 AWG, 600 volt insulated wire. Power wires are susceptible to noise and hum
pickup; therefore it is preferable that you keep power wire runs as short as possible.
This telephone entry system contains a number of static sensitive components that can be damaged
or destroyed by static discharges during installation or use. Discharge any static prior to removing
the circuit board from the lobby panel by touching a proper ground device.
Proper grounding of this system is a requirement. The use of surge suppressers can significantly
reduce the chance of component failure because of static charges or surges. To be effective, ground
connections should be made with a minimum 12 AWG, 600 volt insulated wire to a ground point
within 10 feet of the telephone entry system. The ground point must be at an electrical panel, a
metallic cold water pipe that runs in the earth, or a grounding rod driven at least ten (10) feet into the
soil.
Be sure that you use proper wire that has an insulation rated for an underground environment. All
wires should be placed in conduits. Proper pre-planning can greatly ease the installation and wiring
of this system. Always check with the local building code to determine the type of wire required in
your municipality.
21
Contrast
Display Terminal
Switch 2
Input
Master
Code
Memory
Chip
Click
Sensitivity
Keypad
Terminal
Feedback
Hands Free
Ring Pin
Handset
Volume
Relay 2 Terminals
Power Wiring Maximum Distance
Phone Wiring Maximum Distance
100 Feet
18AWG
800 Feet
24 AWG
200 Feet
16 AWG
1600 Feet
22 AWG
22
2.1 MAIN TERMINAL DESCRIPTION
TERMINAL
DESCRIPTION
1
Phone Line Connection – 800 ft. maximum with 24 AWG wire; 1600 ft. maximum with 22 AWG wire.
2
Phone Line Connection – 800 ft. maximum with 24 AWG wire; 1600 ft. maximum with 22 AWG wire.
3
Earth Ground Only – Not a Low Voltage Common!
4
Switch Input 1. A closure between terminals 4 and 8 will cause relay 1 to activate for the programmed
strike time. The Postal Switch is connected here.
5
Microphone Input – White Wire.
6
Microphone Input – Green Wire.
7
Speaker Output.
8
Common for switch input 1, speaker and battery NEGATIVE (12 VDC).
9
Microphone Input – Red Wire and battery POSITIVE (12 VDC).
10
Relay 1 Common.
11
Relay 1 Normally Closed (N.C.).
12
Relay 1 Normally Open (N.O.).
13
16 VAC Input Power – 20 VA minimum.
100 ft. maximum with 18 AWG wire; 200 ft. maximum with 16 AWG wire.
14
16 VAC Input Power – 20 VA minimum.
100 ft. maximum with 18 AWG wire; 200 ft. maximum with 16 AWG wire.
Do not run high voltage (115 V) power lines and communication lines in the same conduit. These
should be in separate conduits at least six (6) inches apart. Be sure that all phone line wiring is
twisted and completely isolated from ground.
Use only the supplied 16.5 VAC (or U.L. listed equivalent) to power the entry system. Do not power
any other devices (electric strikes, magnetic locks, lights, etc.) from this transformer. Do not
run 16 VAC entry system power lines over 200 feet. It is advisable to keep these wires as short as
possible. Use 18 AWG wire for wire runs up to 100 feet, and 16 AWG wire for wire runs up to
200 feet. Install a low voltage surge suppresser (DoorKing p/n 1878-010 or equivalent) to help
protect the entry system from power surges.
Relay 1 contacts are located on the main terminal strip (10, 11, 12). Relay 2 contacts are located on
an auxiliary terminal strip above terminals 9 and 10 and are labeled on the board left to right: NO, NC,
C.
A 12 volt .8 amp hour gel-cell battery (DoorKing p/n 1801-008) can be installed in the system to
provide stand-by power in the event of a power outage. Connect the positive (RED) lead to terminal
9; connect the negative (BLACK) lead to terminal 8.
23
2.2 WIRING DESCRIPTION
The wiring diagram below shows a typical wiring scheme for the telephone entry system.
•
Terminal 3 is a case ground and not a low voltage common. Using terminal 3 as a low
voltage common will cause noise on the phone line.
•
Switch input 1 (terminals 4 and 8) is pre-wired to the postal switch and pre-programmed to
activate relay 1 when the input is closed.
•
Switch input 2 can be programmed to activate relay 2 or dial a preprogrammed phone
number when the input is closed.
Normally Open
Switch 2 Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Central Office
Phone Line
+
Earth Ground
Only
Normally Open
Switch 1 Input
24
12 Volt
Battery
16 VAC, 20 VA
Transformer
2.3 RELAY WIRING (TYPICAL)
2.3.1 Controlling a Single Door or Gate
Relay 2 Terminal
Connections
Gate
Operator
OR
Electric
Strike
OR
Magnetic
Lock
25
Relay 2 Common
Main
Terminal
Strip
Relay 2 Normally Closed
Relay 2 Normally Open
12 Relay 1 Normally Open
11 Relay 1 Normally Closed
10 Relay 1 Common
Relay 1 is typically used when the system will control a single door or vehicular gate operator. Note
that the electric strike and magnetic lock are each powered by their own power supply. Electric
strikes are connected through the normally open (NO) contact and magnetic locks are connected
through the normally closed (NC) contact.
2.3.2 Controlling a Gate Operator and Pedestrian Gate (or Door)
Relay 2 Common
Main
Terminal
Strip
Relay 2 Normally Closed
Relay 2 Normally Open
12 Relay 1 Normally Open
11 Relay 1 Normally Closed
10 Relay 1 Common
When controlling a gate operator and pedestrian gate (or door), relay 1 is typically used to control the
gate operator while relay 2 is typically used to control the door or pedestrian gate. Note that the
electric strike and the magnetic lock are powered from their own power supply. The normally open
(NO) contact is used for electric strikes and the normally closed (NC) contact is used for magnetic
locks.
A variation of this diagram is for the system to control two doors or two gates.
Relay 2 Terminal
Connections
AND
Magnetic
Lock
OR
Gate
Operator
Electric
Strike
26
SECTION 3 – PROGRAMMING
The DoorKing 1802, 1803, 1808 and 1810 Telephone Entry Systems can be programmed from the
keypad on the front of the entry system, or remotely from an off premise location using a touch tone
telephone. When programming from an off site location with a touch-tone telephone, the RING pin
must be installed on the circuit board (see Section 4). We recommend that you do not attempt
programming from an off site location until you become familiar with these programming instructions.
Programming from the Keypad
Follow the programming instructions as described in each section of this manual. The system will
prompt you with short (beep) tones when programming steps have been followed correctly, and with
a long tone (beeeeeep) when the programming step is ended. The 1802, 1803 and 1810 systems
have an LCD display that will prompt you for information that you will need to enter.
Programming from an Offsite Location
Follow these steps when programming the system from an offsite location. You must use a touchtone telephone and the RING pin must be installed to perform off site programming.
1. Call the telephone number that the entry system is installed on from a touch-tone
telephone. The entry system will answer with a one second tone.
2. Follow the programming instructions as described in each section of this manual. The
system will prompt you with short (beep) tones when programming steps have been
followed correctly.
3. When complete, hang up. (You cannot use 0 # to end remote programming sessions).
Programming Notes
When each programming step is performed correctly, a short tone (beep) will be heard. When the
programming session is ended, a long tone (beeeeeep) will be heard.
This symbol
per symbol.
B in the programming steps indicates numbers that you will need to enter, one number
The amount of telephone numbers that can be programmed into the system is dependent on the
memory size ordered. Memory sizes available are 25 - 75 - 125 - 250 - 500 - 1000. The memory size
also determines the number of four-digit entry codes (memory size + 12) that can be programmed
into the system. Five-digit entry codes are limited to six.
27
3.1 GENERAL PROGRAMMING
3.1.1 Master Code
This programming step sets the system MASTER CODE. The master code is the four-digit number
required to gain access to the system memory. You need to know the master code prior to
performing any of the programming functions on the following pages.
NOTE: The master code cannot be programmed from an off-site location. The master code
can only be programmed from the system keypad.
Factory setting = 9999
1. Open the cabinet of the telephone entry system and turn the master code switch (the
small toggle switch) on.
2. Enter a four-digit master code
then press (beep).
3. Turn the master code switch off and close the cabinet.
BBBB
3.1.2 Single or Multiple Systems
This program sequence sets the telephone entry system to operate as a single unit on the phone line,
or to share the phone line with other units. If multiple systems are sharing the same phone line, then
each one must be set as a "multiple system" and each must have a unique master code.
Factory setting = Single System.
and then enter the four-digit MASTER CODE BBBB (beep).
(beep) for a single system or (beep) for multiple systems.
Press TOGETHER to end this programming step (beeeeeep).
1. Press
2. Enter
3.
3.1.3 Relay Strike Time
These steps will program Relay 1 and Relay 2 strike times. Strike times can be programmed from 1/4
second (enter 00 in step 3) up to 99 seconds by entering the desired time in seconds.
Factory setting for relay strike times are: Relay 1 = 01, Relay 2 = 01.
1.
2.
3.
4.
5.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
to set relay 1, or
to set relay 2 strike time.
Enter the two-digit strike time
(00-99) then press (beep).
Repeat steps 2 and 3 to set the other relay strike time.
Press
TOGETHER to end this programming step (beeeeeep).
BB
28
3.1.4 Talk Time
This programming sequence sets the maximum time allowed for conversation when the entry system
places a call to the resident. The talk time can be set from 1 second up to 255 seconds (4 minutes,
15 seconds) and is entered as a three-digit number. For example, to set a talk time of 20 seconds,
enter 020 in step 3. The talk time set here does not affect the telephone numbers that are
programmed under directory codes 0, 00, 000, 0000 and 1, 01, 001, 0001. The talk time for these
two directory codes are factory set to the maximum. Phone numbers programmed under these
directory codes should be reserved for management or emergency phone numbers that generally
require longer conversations.
Factory setting for talk time = 60 seconds.
BBBB
and enter the four digit MASTER CODE
(beep).
1. Press
2. Enter three digits for talk time (seconds)
(001-255) then press
3. Press
TOGETHER to end this programming step (beeeeeep).
BBB
(beep).
3.1.5 Tone Open Numbers
These steps will program the tone open numbers for relays 1 and 2. You will need to enter a fourdigit number (see chart below) to set the relay functions. If a function is not desired, enter # in place
of a number. For example, if you want the relay to have a momentary activation function only, and
you want the relay to activate when the number 9 is pressed, enter
in step 3. Do not
duplicate tone open numbers, i.e., don’t set relay 1, and 2 tone-open numbers to 9.
Factory setting is: Relay 1 = 9876, Relay 2 = 5432.
1.
2.
3.
4.
5.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
to set relay 1 or
to set relay 2 tone numbers.
Enter the four-digit tone open number code
then press (beep).
Repeat steps 2 and 3 to set the other relay tone open numbers.
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
DIGIT
1
FUNCTION
Momentary activation. Relay will activate for the programmed strike time (3.1.3).
2
Relay hold. Relay will activate and remain activated until commanded to release.
3
Relay release. Deactivates the relay hold command.
4
Relay hold 1-hour. Relay will activate for 1-hour and then will automatically deactivate itself.
29
3.1.6 Postal Switch
This programming sequence will set how the two switch inputs on the telephone entry system control
board will operate. Switch input 1 is labeled PSW (postal switch) and is found on terminal 4 of the
main terminal strip. Switch input 2 is a two terminal auxiliary input located on the upper left hand
corner of the control board. These switch inputs can be programmed to activate their respective
relays (switch 1 - relay 1, switch 2 - relay 2). They can also be programmed so that switch 1 dials out
the phone number programmed in directory code 0, 00, 000, or 0000, and switch 2 dials out the
phone number programmed in directory code 1, 01, 001, or 0001. Each switch is programmed
independently.
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
(beep) to set switch 1, or press
(beep) to set switch 2.
Press
(beep) to set the switch input to activate the relay, or press
set the switch input to dial-out a preprogrammed phone number.
TOGETHER to end this programming step (beeeeeep).
Press
(beep) to
3.1.7 Touch-tone / Rotary-dial
This programming sequence will set the telephone entry system to dial out in either a touch-tone or
rotary format. Generally, this will be set for touch-tone.
Factory setting = touch-tone.
1.
2.
3.
and enter the four digit MASTER CODE BBBB (beep).
(beep) for touch-tone or enter (beep) for rotary.
Press TOGETHER to end this programming step (beeeeeep).
Press
Enter
3.1.8 Number of Rings to Answer
This programming sequence sets the number of rings to allow before the telephone entry system
answers a call placed to it. This programming sequence does not affect the number of times that a
resident’s telephone will ring when a call is placed from the entry system to the resident.
1.
2.
3.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the number of rings
then press (beep).
Press
TOGETHER to end this programming step (beeeeeep).
BB
30
3.1.9 Keypad Function
This programming sequence sets the function of the 0 through 9, and the # keys on the keypad
during conversation. The keys can be set to hang-up the entry system when they are pressed during
conversation, or they can be programmed to DTMF tone out during conversation. The later may be
desirable if the entry system is used with an auto-attendant type telephone system where the caller is
prompted to enter numbers from a touch-tone telephone. HINT: If DTMF tones are required, program
the # or * key to hang-up the system.
1.
2.
3.
4.
5.
BBBB
and enter the four-digit MASTER CODE
(beep).
Press
Enter the desired key number then press (beep).
Press
(beep) for hang-up, or press
(beep) for touch-tone.
Repeat steps 3 and 4 to program other keys.
Press
TOGETHER to end this programming step (beeeeeep).
B
3.1.10 Star (*) Key Function
This programming sequence sets the function of the
key on the keypad during conversation. This
key can be set to hang-up the entry system when pressed during conversation, or it can be
programmed to touch-tone out during conversation.
1.
2.
3.
Press
Press
Press
and enter the four-digit MASTER CODE BBBB (beep).
(beep) for hang-up, or press (beep) for touch-tone.
TOGETHER to end this programming step (beeeeeep).
31
3.2 PHONE NUMBER PROGRAMMING
3.2.1 Programming the Directory Code Length
This programming sequence sets the directory code length to 1 - 2 - 3 or 4 digits. If 11 or more
resident names or telephone numbers are going to be programmed into the system, the directory
code must be at least two-digits. If 101 or more resident names or telephone numbers are going to
be programmed, the directory code must be at least three-digits.
Factory setting is three (3) digits.
CAUTION: This programming sequence will delete all phone numbers and directory codes
that have been previously programmed into the system.
BBBB
1. Press
and enter the four-digit MASTER CODE
(beep).
2. Enter the directory code digit length (1-2-3-4)
then press
(beep). This programming
sequence will automatically end itself. This will be indicated by a long tone (beeeeeep).
B
3.2.2 Programming 7-digit Phone Numbers
In this programming sequence, the directory codes and 7-digit phone numbers will be programmed
into the system. Be sure you have programmed the directory code length that you desire as
described in 3.2.1. Changing the directory code length after programming the telephone
numbers will erase all the numbers and directory codes that have been programmed. To
program phone numbers that will be referenced to an area code (long distance calls and 10 digit
calling), follow the instructions under Long Distance Phone Number Programming on the next page.
If you use directory codes 0, 00, 000, 0000 and/or 1, 01, 001, 0001 remember that the talk time for
these directory codes are factory set to the maximum and cannot be changed. Use these directory
codes to program management or emergency phone numbers, which generally require longer
conversation periods.
NOTE: If this telephone entry system is being used in an area that requires 10-digit dialing,
proceed to 3.2.3 and 3.2.4 to program the area code and phone number.
BBBB
1. Press
and enter the four-digit MASTER CODE
(beep).
2. Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in 3.2.1)
then press (beep).
3. Enter the seven-digit phone number
then press
(beep). If the number
that you are entering in this step is less than seven-digits, enter # in the empty spaces.
For example, if the system is connected to a PBX that requires four-digit extension
numbers and you want to enter extension 2217, you would enter this number as
then press (beep).
4. Repeat steps 2 and 3 to enter additional directory codes and phone numbers.
5. Press
TOGETHER to end this programming step (beeeeeep).
B
BBBBBBB
32
3.2.3 Programming Area Codes
Up to 10 different area codes can be programmed for any 10-digit or long distance calling
requirements and will be referenced 0 through 9 (for a total of 10). The area codes will be entered as
a four-digit number (1 + the three digit area code). If area codes are being programmed to facilitate
10-digit calling requirements, precede the three-digit area code with #.
1.
2.
3.
4.
5.
BBBB
B
Press
and enter the four-digit MASTER CODE
(beep).
Enter the area code reference number (0 through 9) then press  EHHS
Enter the area code
then press
(beep). NOTE-1: for long distance calling
requirements, enter 1 and the three-digit area code. NOTE-2: for 10-digit calling
requirements, enter # and the three-digit area code.
Repeat steps 2 and 3 to enter additional area codes. Remember to use a different
area code reference number when entering more area codes.
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
3.2.4 Programming Phone Numbers with Area Code Reference
In this section, phone numbers that are referenced to an area code (long distance and 10-digit dialing
calls) will be programmed. Be sure that the area code(s) have been programmed as described in the
preceding section.
NOTE: If long distance or 10-digit dialing is not required, program the seven digit telephone
numbers as described in 3.2.2.
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in
3.2.1) then press (beep).
Enter the area code reference number then press (beep).
Enter the seven-digit phone number
then press
(beep). If the
number that you are entering in this step is less than seven-digits, enter # in the
empty spaces. For example, if the system is connected to a PBX that requires fourdigit extension numbers and you want to enter extension 2217, you would enter this
number as
then press (beep).
Repeat steps 2, 3, and 4 to enter additional long distance phone numbers.
Press
TOGETHER to end this programming step (beeeeeep).
B
BBBBBBB
5.
6.
3.2.5 Deleting Individual Phone Numbers
This programming sequence is used to delete a single phone number under a known directory code.
1.
2.
3.
4.
5.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in
3.2.1) then press (beep).
Press
then press (beep).
Repeat steps 2 and 3 to delete additional phone numbers.
Press
TOGETHER to end this programming step (beeeeeep).
33
3.2.6 Delete All Phone Numbers
This programming step deletes all phone numbers previously programmed into the system.
CAUTION: this programming step is irreversible once it is started.
1.
2.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
then press
(beep). This programming sequence will automatically
end itself. This will be indicated by a long tone (beeeeeep).
Sections 3,2,7 and 3.2.8 apply only to 1802, 1803 and 1810 units.
3.2.7 Display / Delete Phone Numbers
This program sequence is useful to display phone numbers when you do not know what directory
code they have been programmed under. This sequence also gives you the option to delete the
phone number after it is displayed.
1.
2.
3.
4.
5.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
The first directory code will be displayed. Press
to view the phone number
programmed under this directory code. If the first digit is flashing, this is the area
code reference number and indicates a long distance phone number.
Press to go to the next step.
Press
to move forward to the next directory code, or press
to delete the shown
phone number and move forward to the next directory code.
After the last phone number is displayed and
or
is pressed, this programming
sequence will automatically end itself. This will be indicated by a long tone
(beeeeeep) or you can press
TOGETHER to end this programming step at any
time (beeeeeep).
3.2.8 Display Phone Numbers with known Directory Codes
Use this programming sequence to display phone numbers programmed under known directory
codes, i.e. if you wanted to see what phone number was programmed under directory code 2719
(assuming directory codes have been programmed for four digits). This programming sequence will
not allow you to delete phone numbers.
1.
2.
3.
4.
5.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the directory code (1, 2, 3 or 4 digits depending on what was programmed in
3.2.1).
The phone number programmed under the directory code entered in step 2 will be
displaced on the programming display. If C C C C C C C is displayed, this indicates
that no phone number has been programmed under the entered directory code. If the
first digit is flashing, this is the area code reference code and indicates that the
number displayed is a long distance number.
To display additional phone numbers press and repeat step 2.
Press
TOGETHER to end this programming step (beeeeeep).
34
3.3 ENTRY CODE PROGRAMMING
3.3.1 Four-Digit Entry Code Programming
This programming sequence programs four-digit entry codes into the system memory. The number of
four-digit entry codes that can be programmed is the same as the telephone number memory
capacity, plus 12. We suggest that all entry codes that are programmed into the system be listed with
the names of persons that they have been assigned to (see appendix).
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the four-digit entry code
then press (beep).
Repeat step 2 to enter additional entry codes.
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
3.3.2 Delete Four-Digit Entry Codes
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the four-digit entry code
to be deleted and then press (beep).
Repeat step 2 to delete more entry codes.
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
3.3.3 Delete All Four-Digit Entry Codes
This programming sequence deletes all four-digit entry codes that have been programmed
into the system. CAUTION: this programming step is irreversible once it is started.
1.
2.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
then press
(beep). This programming sequence will automatically
end itself. This will be indicated by a long tone (beeeeeep).
3.3.4 Four-Digit Entry Code Divide Number
The four-digit entry codes can be made to activate either relay 1 or relay 2 by programming a fourdigit divide number. Four-digit entry codes equal to or less than the divide number will activate relay
1. Four-digit entry codes greater than the divide number will activate relay 2. HINT: you can make all
four-digit entry codes (except 0000) activate relay 2 by programming divide number 0000, or make all
four-digit entry codes activate relay 1 by programming divide number 9999.
The factory default divide number is 9999.
1.
2.
3.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the four-digit divide number
then press (beep).
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
35
3.3.5 Five-Digit Entry Code Programming
This programming sequence programs five-digit entry codes into the system memory. The number of
five digit entry codes that can be programmed is limited to six. We suggest that all entry codes that
are programmed into the system be listed with the names of persons that they have been assigned to
(see appendix).
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the five-digit entry code
then press (beep).
Repeat step 2 to enter additional entry codes.
Press
TOGETHER to end this programming step (beeeeeep).
BBBBB
3.3.6 Delete Five-Digit Entry Codes
1.
2.
3.
4.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the five-digit entry code
then press (beep).
Repeat step 2 to delete more entry codes.
Press
TOGETHER to end this programming step (beeeeeep).
BBBBB
3.3.7 Delete All Five-Digit Entry Codes
This programming sequence deletes all five-digit entry codes that have been programmed into
the system. CAUTION: this programming step is irreversible once it is started.
1.
2.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
then press
(beep). This programming sequence will automatically
end itself. This will be indicated by a long tone (beeeeeep).
3.3.8 Five-Digit Entry Code Divide Number
The five-digit entry codes can be made to activate either relay 1 or relay 2 by programming a five-digit
divide number. Five-digit entry codes equal to or less than the divide number will activate relay 1.
Five-digit entry codes greater than the divide number will activate relay 2. HINT: you can make all
five-digit entry codes (except 00000) activate relay 2 by programming divide number 00000, or make
all five-digit entry codes activate relay 1 by programming divide number 99999.
1.
2.
3.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the five-digit divide number
then press (beep).
Press
TOGETHER to end this programming step (beeeeeep).
BBBBB
36
3.4 TIME FUNCTIONS PROGRAMMING
3.4.1 Time Clock Programming
This programming sequence programs the calendar chip in the telephone entry system for the current
time and date. The calendar chip must be programmed if you are going to use any of the time
functions available with the entry system.
1.
2.
3.
4.
5.
6.
7.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the current hour and minutes
then press
(beep). Do not use military
(24 hour) time format, simply enter the hour (2 digits) and the minutes (2 digits). For
example, 8:30 is entered as 0830 whether it is AM or PM.
Press
(beep) for AM, or press
(beep) for PM.
Enter the month
then press (beep).
Enter the day of the month
then press (beep).
Enter the year
then press (beep).
Enter the day of the week (Sun = 1, Sat = 7) then press (beeeeeep).
BBBB
BB
BB
BB
B
3.4.2 Automatic Relay Activation Time Zones
This program sequence sets up time zones to automatically activate and deactivate the relays on the
control board. Each relay can be programmed with two independent time zones. Time zones 1 and 2
affect relay 1 operation; time zones 3 and 4 affect relay 2 operation. Use the chart in the appendix to
record the time zones that are programmed. These time zones can be independently turned on or
turned off after they have been programmed (see operating instructions 5.2.5).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the time zone number then press (beep).
Press
(beep) to turn the time zone ON, or press
(beep) to turn the time zone
OFF.
Enter the beginning hour and minutes
then press (beep).
Press
(beep) for AM, or press
(beep) for PM.
B
BBBB
Enter the ending hour and minutes BBBB then press (beep).
Press (beep) for AM, or press (beep) for PM.
Enter the days of the week BBBBBBB then press (beep). To skip any days of
the week, enter # in place of the day. For example, to have a time zone active on
Saturday and Sunday only (Sun = 1, Sat = 7), enter 1 7 # # # # #.
Repeat steps 2 through 8 to enter additional time zones.
Press
TOGETHER to end this programming step (beeeeeep).
37
3.4.3 Four-Digit Entry Code Time Zone
This programming sequence sets up a time zone for the four-digit entry codes. This time zone uses a
range of four-digit entry codes and can be programmed for certain days of the week. This time zone
can be turned on and turned off after it is programmed (see operating instructions 5.2.4).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
(beep) to turn the time zone ON, or press
(beep) to turn the time zone
OFF.
Enter the beginning hour and minutes
then press
(beep). (Four-digit entry
codes that are within the boundaries of the time zone will begin to work at this time.)
Press
(beep) for AM, or press
(beep) for PM.
Enter the ending hour and minutes
then press
(beep). (Four-digit entry
codes that are within the boundaries of the time zone will cease to work at this time.)
Press
(beep) for AM, or press
(beep) for PM.
Enter the days of the week
then press
(beep). To skip any days of
the week, enter # in place of the day. For example, to have a time zone active on
Saturday and Sunday only (Sun = 1, Sat = 7), enter 1 7 # # # # #.
Enter the lower four-digit boundary
then press (beep).
Enter the upper four-digit boundary
then press (beep).
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
BBBB
BBBBBBB
BBBB
BBBB
3.4.4 Five-Digit Entry Code Time Zone
This programming sequence sets up a time zone for the five-digit entry codes. This time zone uses a
range of five-digit entry codes and can be programmed for certain days of the week. This time zone
can be turned on and turned off after it is programmed (see operating instructions 5.2.4).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Press
(beep) to turn the time zone ON, or press
(beep) to turn the time zone
OFF.
Enter the beginning hour and minutes
then press
(beep). (Five-digit entry
codes that are within the boundaries of the time zone will begin to work at this time.)
Press
(beep) for AM, or press
(beep) for PM.
Enter the ending hour and minutes
then press
(beep). (Five-digit entry
codes that are within the boundaries of the time zone will cease to work at this time.)
Press
(beep) for AM, or press
(beep) for PM.
Enter the days of the week
then press
(beep). To skip any days of
the week, enter # in place of the day. For example, to have a time zone active on
Saturday and Sunday only (Sun = 1, Sat = 7), enter 1 7 # # # # #.
Enter the lower five-digit boundary
then press (beep).
Enter the upper five-digit boundary
then press (beep).
Press
TOGETHER to end this programming step (beeeeeep).
BBBB
BBBB
BBBBBBB
BBBBB
BBBBB
38
3.4.5 Flash Entry Codes
This programming sequence sets up "FLASH" four-digit entry codes. Flash codes are entry codes
that will operate on a specific day of the month only - they will not operate before or after the
programmed day. The flash code will be valid for a single 24-hour period only. For example, if you
program a flash code on July 1st to be active on the 10th, the code will become valid at 00:00 AM on
July 10th and expire at 11:59 PM. The code will not be valid on August 10th. You can program up to
eight flash codes in the system. Flash codes 1 through 4 will activate relay 1, flash codes 5 through 8
will activate relay 2.
1.
2.
3.
4.
5.
6.
BBBB
Press
and enter the four-digit MASTER CODE
(beep).
Enter the flash code number (1 - 8) then press (beep).
Enter the day of the month that the code is to be active
then press (beep).
Enter the four-digit FLASH ENTRY CODE
then press (beep).
Repeat steps 2 through 4 to enter additional flash codes.
Press
TOGETHER to end this programming step (beeeeeep).
B
BBBB
39
BB
Contrast
Display Terminal
Switch 2
Input
Master
Code
Memory
Chip
Click
Sensitivity
Keypad
Terminal
Feedback
Hands Free
Ring Pin
Handset
Volume
Relay 2 Terminals
40
SECTION 4 – ADJUSTMENTS
4.1
Speaker Volume
1. Open the front of the telephone entry system and locate the speaker volume adjustment.
2. Place a phone call from the telephone entry system to a resident. While they are talking,
adjust the speaker volume potentiometer for adequate sound. To increase the volume
rotate the potentiometer clockwise, to decrease the volume rotate the potentiometer
counter clockwise.
4.2
Feedback
1. Open the front of the telephone entry system and locate the feedback adjustment.
2. Place a phone call from the telephone entry system to a resident. After they answer, ask
the resident to remain silent.
3. While rubbing your finger across the microphone hole, rotate the feedback potentiometer
clockwise, and then counter clockwise. When the noise from the speaker is minimum,
this is the correct adjustment for the feedback potentiometer.
4.3
Click Sensitivity
1. Open the front of the telephone entry system and locate the click sensitivity adjustment.
2. Place a phone call from the telephone entry system to a resident with a rotary dial type
phone. After they answer, ask the resident to dial 9 while you adjust the click sensitivity
potentiometer (the resident may have to dial 9 several times for you to obtain the correct
adjustment). When the door or gate opens, this is the correct adjustment for the click
sensitivity.
3. NOTE: Adjusting the click sensitivity too high (potentiometer fully clockwise) could cause
the system to respond to loud noises while it is in use. If this happens, rotate the click
sensitivity potentiometer counter clockwise 1/8 turn and re-test the system. You may
have to perform this step several times to find the correct adjustment.
4.4
Display Contrast (1802, 1803, 1810 only)
1. Open the front of the telephone entry system and locate the contrast adjustment.
2. Turn the master code switch on. The display will read MST CODE. While the display is
lighted, turn the contrast potentiometer clockwise and then counter clockwise until the
display is satisfactory.
3. Turn the master code switch off.
4. NOTE: Approximately 30 seconds after the master code switch is turned on, the system
will signal a long tone. This is normal and can be ignored. After the master code switch is
turned off, the display will read MST CODE for approximately 30 seconds.
41
4.5
Master Code Switch
The master code switch is left in the off position for normal operation. Turn the master code switch on
when setting the system master code. See programming instructions to set the system master code.
If the master code switch is turned on and a new master code is not entered, the system will sound a
long tone after approximately 30 seconds. This tone will continue every 30 seconds until a new
master code is entered, or until the switch is turned off. After the switch is turned off, the display
(1802, 1803, 1810 only) will remain lit for approximately 30 seconds, and then will go off.
4.6
Ring Pin
The ring pin-shorting bar is labeled RING on the control board. This shorting pin must be installed to
allow the system to answer any calls placed to it. If remote programming or remote relay operation is
to be used, the shorting bar must be installed. Removing the shorting bar will cause the system to
never answer any call placed to it.
4.7
Handset / Hands Free
The handset shorting pins are labeled HS, and the hands free shorting pins are labeled HF on the
control board. The shorting bar is factory set and will be placed in the HF position for hands free
operation, or will be placed in the HS position for those entry systems ordered with the optional
handset. Do not place shorting bars on both the HS and HF pins at the same time.
42
SECTION 5 – OPERATING INSTRUCTIONS
5.1 GENERAL INSTRUCTIONS
5.1.1 Guest Instructions
Instructions on the faceplate of the unit will instruct guest on the operation of the telephone entry
system. Guests will locate a residents name and directory code in a directory associated with the
telephone entry system. This may be a letter board type directory, an add-on directory or a built-in
directory like that found in the 1810 unit.
When a directory code is entered on the keypad, the telephone entry system will call the
preprogrammed telephone number stored under that directory code. If the line is busy, the system
will emit a busy signal. Pressing the hang-up key (any key or the preprogrammed hang-up key) will
hang the system up. Guest can then try again. Residents can avoid missing calls from the telephone
entry system by ordering call waiting from the local telephone company.
The system can be programmed so that the keypad emits DTMF tones after a connection is made.
For example, in a business application, a call from the telephone entry system may be answered by
an auto-attendant requesting that you enter a person’s extension number. This is possible with the
system provided that it has been programmed to emit DTMF tones once the call is answered.
5.1.2 Responding to a Guest Call
When communication is established, the resident has the option of opening the door(s) or gate(s) by
pressing the programmed tone open number(s) on their touch tone telephone, or they can deny
access to their guest by pressing # on their telephone. If access is granted, the resident will hear a
confirmation tone in their handset indicating that the door or gate has opened, then the system will
automatically hang up.
Residents should be instructed by management to always press the # key on their telephone if
they wish to deny a guest access. If a resident hangs up to deny access instead of pressing #, the
telephone entry system will remain on line until its programmed talk time expires or until it detects dial
tone.
Some newer type telephones emit a short tone rather than a continuous tone when their keys are
pressed. This may cause the telephone entry system to not respond to the tone open number. If this
happens, simply press the tone open number twice in rapid succession to open the door or gate.
If a resident is using rotary dial telephone, they will grant access to their guest by dialing 9. To deny
access to their guest, residents with rotary phones must simply hang up.
5.1.3 Using an Entry Code
The four and five-digit entry codes will operate either relay 1, relay 2, or they can be programmed so
that certain codes will activate only relay 1 while others will activate only relay 2. Both four and fivedigit entry codes can be time zone restricted.
1. To use four-digit codes, press and then enter the four-digit entry code
.
2. To use five-digit codes, press
and then enter the five-digit entry code
.
BBBB
BBBBB
If management decides to utilize resident entry codes, residents should be instructed to keep their
unique code secret. Telling other persons their code or allowing other persons to use their code
compromises security and defeats the purpose of the system.
43
5.2 SYSTEM ADMINISTRATOR
The administrator can perform the following operations from a remote location using a touch-tone
telephone. You must know the phone number of the system and the system master code.
5.2.1 Remote Programming
1. Call the telephone number that the entry system is installed on. The system will answer
with a short tone (beep). Note: the number of rings before the system answers is
dependent on the programming in 3.1.8.
2. After the system answers, follow the desired programming steps in Section 3.
3. When complete, hang up. You cannot use 0# together to end the programming step from
a touch-tone telephone.
5.2.2 Remote Relay Activation
1. Call the telephone number that the entry system is installed on. The system will answer
with a short tone (beep). Note: the number of rings before the system answers is
dependent on the programming in 3.1.8.
2. Press
and enter the four-digit MASTER CODE
(beep).
3. Press the desired tone open number
(beep). NOTE: Refer to 3.1.5 to determine
which tone open features have been programmed, i.e. momentary open, hold open,
release, hold open one hour and then release.
4. Hang up.
B
BBBB
5.2.3 Relay Check
The telephone entry system can be called and a check can be made to determine if any of the relays
in the system are in a "hold open" mode. This check can be useful if yourr gate (or door) is held open
and you suspect that the telephone entry system relay may be the cause.
1. Call the telephone number that the entry system is installed on. The system will answer
with a short tone (beep). Note: the number of rings before the system answers is
dependent on the programming in 3.1.8.
2. Press
and enter the four-digit MASTER CODE
(beep).
3. The system will emit a series of short tones if the relay is in a continuous activation mode.
Relay 1 activated:
beep - pause - beep - pause . . .
Relay 2 activated:
beep beep - pause - beep beep - pause . . .
Relay 1 & 2 activated:
beep beep beep - pause - beep beep beep - pause . . .
4. Press the programmed tone number
to deactivate the relay (beep). The system will
automatically hang up.
BBBB
B
44
5.2.4 Entry Code Time Zone Enable / Disable
The entry code time zones can be turned off or on remotely from a touch-tone telephone at any time
without changing the time zone boundaries. To program the time zone boundaries, see sections
2.4.3 and 2.4.4. Entry code time zones can also be turned off or on at the system keypad by skipping
step 1 and proceeding directly to step 2 in the sequence below.
1. Call the telephone number that the entry system is installed on. The system will answer
with a short tone (beep). Note: the number of rings before the system answers is
dependent on the programming in 3.1.8.
2. Press
for four-digit entry code time zones or press
for five-digit entry code
time zones.
3. Enter the four-digit master code
(beep).
4. Press
(beep) to turn the time zone OFF, or press
(beep) to turn the time zone
ON.
5. Hang up or if at the system keypad, press
together (beeeeeep).
BBBB
5.2.5 Auto Relay Time Zone Enable / Disable
The four time zones that automatically activate and deactivate the relays can be turned off or on from
a touch-tone telephone at any time without changing the time zone boundaries. To program the auto
relay activation time zone boundaries, see section 2.4.2. Auto relay time zone boundaries can also
be turned off or on at the system keypad by skipping step 1 and proceeding directly to step 2 in the
sequence below.
1. Call the telephone number that the entry system is installed on. The system will answer
with a short tone (beep). Note: the number of rings before the system answers is
dependent on the programming in 3.1.8.
2. Press
and enter the four-digit master code
(beep).
3. Enter the time zone number that you want to turn off or on, then press (beep).
4. Press
(beep) to turn the time zone OFF, or press
(beep) to turn the time zone
ON.
5. Hang up or if at the system keypad, press 0# together (beeeeeep).
BBBB
B
45
5.3 MISCELLANEOUS OPERATING INSTRUCTIONS
5.3.1 Switch Input Operation
The two switch inputs can be programmed to either activate their respective relay (switch 1 input
activates relay 1; switch 2 input activates relay 2) or they can be programmed to call the phone
number programmed under the first two directory codes (switch 1 input calls the phone number
programmed under directory code 0, 00, 000 or 0000; switch 2 input calls the phone number
programmed under directory code 1, 01, 001 or 0001). Each switch input is programmed
independently (2.10).
Switch 1 input is typically used as the postal switch and is pre-wired and pre-programmed for postal
switch operation. We suggest that switch input 1 should be left programmed to activate relay 1 to
allow the mail carrier entry.
Switch 2 input can be programmed as the application requires. For example, if the telephone entry
system is controlling a vehicular gate with relay 1 and a pedestrian gate with relay 2, a postal lock box
(DoorKing P/N 1402-080) could be installed at the pedestrian gate for the mail carrier and connected
to switch input 2. In this manner, the postal lock box would allow the mail carrier access through the
pedestrian gate when it is activated. Another use of switch input 2 is to program the input to call a
preprogrammed telephone number instead of activating relay 2. An auxiliary button can be installed
and connected to switch input 2 and labeled “assistance.” When the button is pressed, the system
will automatically dial the phone number programmed under directory code 1, 01, 001 or 0001.
5.3.2 Talk Time
The talk time for directory codes 0, 00, 000, 0000 and 1, 01, 001, 0001 is factory set to 4 minutes 15
seconds and cannot be changed. These directory codes should be reserved for use with
management or emergency phone numbers that typically require longer talk times. For example, if
directory code 000 was programmed to call a management phone number, the system will allow the
full 4 minutes and 15 seconds of talk time before automatically ending the call.
5.3.3 Line Sharing
More than one telephone entry system can share the same phone line provided that the units have
been programmed for multiple systems on the same line (see 3.1.2). When the unit is programmed
for multiple systems sharing the same line, it checks the phone line for 48 volts (not busy) before
attempting to place a call. If the phone line is in use, the system will emit a busy signal. If two or
more systems are sharing the same phone line, it is important that each system be programmed with
its own unique master code. When more than one system is on the same phone line, and a call is
placed from one of the systems to a resident, only the system that placed the call will respond to any
tone open numbers. Do not be concerned that all the units will activate their relay when the resident
presses the tone open number.
46
5.3.4 Connection to a PBX
If the telephone entry system is going to be connected to a PBX system, you may need to program
extension numbers in place of a seven-digit telephone number. To do this, enter the extension
number and fill the remaining spaces with the # key in the phone number programming step. For
example, if the PBX system uses four-digit extensions and you want to program extension 2217 as a
phone number, in step 3, section 3.2.2 press:
3.
(beep).
If the PBX system requires you to dial 9 to obtain an outside line, and you want to program some
outside line phone numbers in the system, program the number 9 as one of the alternate area codes.
In step 3, section 3.2.3 press:
3.
(beep).
Then program the outside phone number as a long distance number (3.2.4) using the area code
reference number used to program 9.
5.3.5 Areas with 10-digit Dialing
If the telephone entry system is installed in an area where the telephone company has instituted 10
digit dialing, simply program the required number of alternate area codes into the system without
preceding the area code with the number 1. If 310 was one of the area codes required, in step 3,
section 3.2.3 press:
3.
(beep).
Then program the outside phone number as a long distance number (3.2.4) using the area code
reference number used to program 310. Program additional area codes and phone numbers as
described in sections 3.2.3 and 3.2.4.
47
48
SECTION 6 – MAINTENANCE
The DoorKing telephone entry system is essentially a maintenance free device. When the unit is
properly installed, it should provide years of trouble free service. Maintenance is limited to updating
the directory and phone number and/or entry codes when residents move in or out.
The faceplate of the unit should be cleaned on a regular basis to keep contaminants in the air from
sticking to the surface and possibly causing pitting. When cleaning the faceplate of the system, never
use an abrasive cleaner or cloth. Stainless steel cleaner works very well with a soft cloth for systems
with a stainless steel faceplate. A clean damp soft cloth should be used to clean gold plated
faceplates.
6.1 TROUBLE SHOOTING
If problems should develop with your telephone entry system, refer to the trouble-shooting guide on
the following pages to try and correct any problems. Our experience has shown that a majority of
reported problems are actually programming related and can be corrected on site. If problems persist
and they cannot be corrected, contact your authorized DoorKing dealer for assistance. Before
performing any trouble-shooting, check the following:
1.
2.
3.
4.
5.
6.
7.
Have a good VOM meter handy to check voltages and continuity.
Have a telephone test set (DoorKing p/n 1800-050 or equivalent) to check the
telephone line. Noise on the phone line will cause problems with the entry system.
Be sure that the entry system case is properly grounded.
Be sure that the telephone wires are twisted.
A hum on the system indicates that the phone line or 16 VAC power lines may be
grounded. Check to be sure that the phone lines or power lines are not shorted to
ground.
Check the 16 VAC system power. Be sure that the transformer is properly rated (16
VAC, 20 VA). Keep the wire run from the transformer to the entry system as short as
possible. Use 16 or 18 AWG, 600 volt insulated wire only. The importance of
proper power wiring cannot be over stressed!
Isolate the telephone entry system. Disconnect any external devices, such as gate
operators, electric strikes, magnetic locks, etc., which may affect the operation of the
system.
49
SYMPTON
POSSIBLE SOLUTION(S)
•
Wrong master code entered. Start over.
•
Waiting too long between pushing buttons. Enter information quicker.
•
Keypad is not plugged into board correctly. Cable points down.
•
Memory chips are installed upside down.
System emits a long
tone and cancels
programming.
•
Waiting too long between pushing buttons.
•
Forgetting to press
Keypad is dead.
•
No power. Check for 16 VAC input power.
•
Check that the keypad is properly connected to the circuit board. The cable on
the plug points down when connected to the circuit board.
•
Disconnect the phone line from the system and check it with a handset. If line
is noisy, problem is with the phone line and not the entry system.
•
Check for any shorts to ground behind the circuit board.
•
Check for pinched wires near the door hinge.
•
Check for 16-volt power shorted to ground.
•
Check for phone line shorted to ground.
•
Check that phone wires are twisted.
•
Check that the proper type of phone wire was used for an outdoor and / or
underground application.
•
Check that all wires, speaker, keypad, etc. are isolated from ground.
•
Check that the cabinet is properly grounded. Be sure that case ground
(terminal 3) is not used as a low voltage common.
Cannot get into
programming mode.
Buzz or noise on the
phone line.
first when programming.
•
Check for excessive voltage drop on 16 VAC power.
Ringing or howling
from the speaker.
•
Feedback improperly adjusted (4.2).
•
Volume is set too high (4.1).
After dial out, dial tone
is heard on the
speaker.
•
Phone line is a rotary-dial line. Have the phone company change it to a touchtone line.
Door strike locks on.
•
Excessive voltage-drop on 16 VAC line.
•
Using a transformer with too low VA rating.
•
Relay strike time programmed too long (3.1.3).
•
Auto relay time zone enabled. Turn auto relay feature off or reprogram the
time zone (5.2.5).
•
System was given a hold open command. Call the system and press the tone
deactivate number (5.2.2).
Entry system will not
answer when called.
•
Ring pin is not installed (4.6).
•
Number of rings to answer is set to high. Reprogram (3.1.8).
•
Bad phone line or insufficient ring voltage.
Rotary dial 9 will not
activate relay.
•
Adjust click sensitivity (4.3).
Touch-tone 9 will not
activate relay.
•
Re-program tone-open number to 9 (3.1.5).
•
If resident phone emits a short pulse rather than a long tone, press 9 twice in
rapid succession
.
•
Try another phone that is known to work.
Door strike or gate
operator holds open.
•
Lower speaker volume (4.1) and re-adjust feedback (4.2).
Relay activates but
gate operator will not
open.
•
Re-program relay strike time for a longer period (3.1.3).
•
Check wiring to gate operator.
•
Check gate operator.
Postal switch will not
activate relay.
•
Be sure that the wire-tie has been clipped off the postal switch.
•
Be sure that the relay has been programmed for postal switch input (3.1.6).
Switch 2 input will not
activate relay.
•
Reprogram switch input 2 to activate relay (3.1.6).
50
SYMPTON
POSSIBLE SOLUTION(S)
Four-digit entry codes
will not work.
•
Forgetting to press # first.
•
Entry code is time zone restricted. Reprogram time zone or turn time zone off
(5.2.4).
•
Entry code attempted was a flash code that is no longer valid.
Five-digit entry codes
will not work.
•
Forgetting to press ## first.
•
Entry code is time zone restricted. Reprogram time zone or turn time zone off
(5.2.4).
Entry codes will not
activate relay 1.
•
Programmed entry codes are greater than the divide number. Reprogram
divide number or program entry codes less than the divide number.
Entry codes will not
activate relay 2.
•
Programmed entry codes are less than or equal to the divide number.
Reprogram divide number or program entry codes greater than the divide
number
System emits a beep
every 30 seconds.
•
Master code switch is in the ON position.
LCD is unreadable
(1802, 1803, 1810
units only).
•
Adjust contrast.
6.2 ACCESSORIES
Surface Trim Ring
Flush Kit
Flush Ring
Stainless Steel Case
Surge Suppressers
Mounting Post
Telephone Test Set
Battery
Use to recess surface mount 1803 or 1810 units into a wall or column.
P/N 1803-150.
Use to install flush style 1803 or 1810 units into a wall or column. Kit
includes rough in back box and trim ring. P/N 1814-165 comes with
stainless steel trim ring. P/N 1814-166 comes with gold plated trim ring.
Use to surface mount a flush style 1803 or 1810 unit. P/N 1814-152.
Replaces the black steel surface mount case on the 1803 and 1810 units
with a stainless steel case. P/N 1810-102.
High voltage (120 V) suppresser: P/N 1878-076.
Phone line suppresser: P/N 1878-077.
Low voltage (28 V) suppresser: P/N 1878-078.
Standard gooseneck mounting post: P/N 1200-045.
Standard gooseneck mounting post – long: P/N 1200-046
Heavy-duty gooseneck mounting post: P/N 1200-047.
Heavy-duty gooseneck mounting post – Long: P/N 1200-048.
Includes clips, cord and carrying case. P/N 1800-050.
12 volt .8 amp hour gel cell provides stand by power during power
interruptions. P/N 1801-008.
51
6.3 LOG TABLES
Complete the information in the tables on the following pages to maintain a record of the information
that has been programmed into the telephone entry system if the system. Make copies of the
resident log sheet so that you have enough to complete a listing of all residents and data.
MASTER CODE
RELAY STRIKE TIME
RELAY 1
TONE OPEN NUMBERS RELAY 1
RELAY 2
TONE OPEN NUMBERS RELAY 2
Momentary
Momentary
Continuous
Continuous
Release
Release
Hold 1 Hour
Hold 1 Hour
AREA CODES
1
2
3
4
5
6
7
8
9
0
4-DIGIT ENTRY CODE TIME ZONE
5-DIGIT ENTRY CODE TIME ZONE
Begin Time
Begin Time
End Time
End Time
Days of Week
Days of Week
Lower Boundary
Lower Boundary
Upper Boundary
Upper Boundary
RELAY AUTO ACTIVATE TIME ZONES
ZONE 1
ZONE 2
Begin Time
End Time
Days of Week
52
ZONE 3
ZONE 4
NAME
PHONE
NUMBER
53
DIRECTORY
CODE
ENTRY
CODE
ALTERNATE
AREA CODE
NAME
PHONE
NUMBER
54
DIRECTORY
CODE
ENTRY
CODE
ALTERNATE
AREA CODE
Make additional copies of this table as needed.
Resident Instruction Sheet
<RXU EXLOGLQJ FRPPXQLW\ KDV EHHQ HTXLSSHG ZLWK D 'RRU.LQJ 7HOHSKRQH (QWU\ 6\VWHP WKDW ZLOO SURYLGH
FRPPXQLFDWLRQ IRU \RXU JXHVW IURP WKH OREE\ GRRU JDWHG HQWUDQFH WR \RXU KRPH E\ XVH RI WKH ORFDO telephone
QHWZRUN ,I \RX KDYH DQ\ TXHVWLRQV UHJDUGLQJ WKH XVH RU RSHUDWLRQ RI WKLV V\VWHP SOHDVH VHH \RXU V\VWHP
DGPLQLVWUDWRU EXLOGLQJ PDQDJHU +2$ UHSUHVHQWDWLYH RU FDOO
Guest Communication
<RXU QDPH RU DSDUWPHQW QXPEHU DQG WHOHSKRQH QXPEHU KDYH EHHQ SURJUDPPHG LQWR WKH WHOHSKRQH HQWU\ V\VWHP
XQGHU D VSHFLILF ',5(&725< &2'( 7KLV GLUHFWRU\ FRGH FDQ EH IURP WR GLJLWV ORQJ GHSHQGLQJ RQ WKH QHHGV RI
WKH DSSOLFDWLRQ :KHQ D JXHVW FRPHV WR YLVLW \RX WKH\ ZLOO ORRN \RXU QDPH XS LQ D GLUHFWRU\ 1H[W WR \RXU QDPH ZLOO
EH OLVWHG \RXU ',5(&725< &2'( :KHQ \RXU JXHVW HQWHUV WKLV FRGH RQ WKH V\VWHP NH\SDG WKH V\VWHP ZLOO SODFH D
FDOO WR \RXU KRPH ,I \RXU JXHVW DOUHDG\ NQRZV \RXU GLUHFWRU\ FRGH WKH\ FDQ VLPSO\ HQWHU WKH FRGH RQ WKH NH\SDG
ZLWKRXW KDYLQJ WR ORRN XS \RXU QDPH
Granting or Denying Access
2QFH \RX KDYH DQVZHUHG WKH SKRQH FDOO DQG \RX KDYH LGHQWLILHG \RXU JXHVW \RX KDYH WKH FKRLFH WR HLWKHU JUDQW DFFHVV
RU GHQ\ DFFHVV WR \RXU JXHVW
7R JUDQW DFFHVV WR \RXU JXHVW SUHVV
RQ \RXU WRXFKWRQH WHOHSKRQH 7KH WHOHSKRQH HQWU\ V\VWHP ZLOO UHVSRQG
ZLWK D FRQILUPDWLRQ WRQH LQGLFDWLQJ WKDW WKH GRRU RU JDWH LV RSHQLQJ DQG ZLOO DXWRPDWLFDOO\ GLVFRQQHFW LWVHOI 6RPH
QHZHU WHOHSKRQHV HPLW D YHU\ VKRUW GXUDWLRQ WRQH ZKHQ WKH QXPEHU LV SUHVVHG ,I \RXU WHOHSKRQH GRHV WKLV \RX PD\
KDYH WR SUHVV WKH RSHQ QXPEHU WZLFH LQ UDSLG VXFFHVVLRQ WR RSHQ WKH GRRU RU JDWH
7R GHQ\ DFFHVV WR \RXU JXHVW SUHVV WKH NH\
5RWDU\ 3KRQH 2QO\ ,I \RX KDYH D URWDU\ GLDO SKRQH GLDO WR JUDQW DFFHVV 7R GHQ\ DFFHVV KDQJ XS
Call Waiting
,I \RX DUH RQ WKH WHOHSKRQH ZKHQ D JXHVW WULHV WR FRQWDFW \RX IURP WKH WHOHSKRQH HQWU\ V\VWHP WKH\ ZLOO KHDU D EXV\
VLJQDO DQG ZLOO KDYH WR ZDLW IRU \RX WR HQG \RXU FDOO EHIRUH WKH\ FDQ FRQWDFW \RX 7R HOLPLQDWH WKLV SUREOHP \RX FDQ
RUGHU FDOO ZDLWLQJ IURP \RXU ORFDO WHOHSKRQH FRPSDQ\
Privacy
,I \RX GR QRW ZDQW \RXU QDPH DQGRU DSDUWPHQW QXPEHU OLVWHG LQ WKH HOHFWURQLF GLUHFWRU\ LQIRUP WKH V\VWHP
DGPLQLVWUDWRU RI WKLV <RXU WHOHSKRQH QXPEHU FDQ EH VWRUHG LQ WKH V\VWHP ZLWKRXW \RXU QDPH EHLQJ GLVSOD\HG RQ WKH
GLUHFWRU\ ,I \RX FKRRVH WKLV RSWLRQ \RX ZLOO QHHG WR LQIRUP \RXU JXHVW RI \RXU GLUHFWRU\ FRGH RWKHUZLVH WKH\ ZLOO
KDYH QR PHWKRG RI FRQWDFWLQJ \RX IURP WKH HQWU\ RI \RXU EXLOGLQJ FRPPXQLW\ WKURXJK WKH WHOHSKRQH HQWU\ V\VWHP
Access Code
<RXU V\VWHP PD\ EH HTXLSSHG ZLWK DQ DFFHVV FRGH WKDW ZLOO DOORZ \RX WR RSHQ WKH GRRU JDWH E\ HQWHULQJ WKLV FRGH RQ
WKH V\VWHP NH\SDG <RXU V\VWHP DGPLQLVWUDWRU ZLOO DGYLVH \RX RI \RXU DFFHVV FRGH LI WKLV RSWLRQ LV DYDLODEOH 7R XVH
WKH DFFHVV FRGH ILUVW SUHVV WKH NH\ DQG WKHQ HQWHU WKH IRXU GLJLW FRGH
6\VWHP $GPLQLVWUDWRU )LOO LQ WKH EODQNV DERYH DQG FRS\ WKLV LQVWUXFWLRQ VKHHW IRU \RXU UHVLGHQWV
55
Download PDF

advertising