Installation guide | D-Link 804HV Network Router User Manual

DI-804HV
This product can be set up
using any current web browser,
i.e., Internet Explorer 6 or
Netscape Navigator 6.2.3.
4-Port Broadband
VPN Router
Before You Begin
1 . If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2 . It’s best to use the same computer that is connected to your modem for configuring
the DI-804HV VPN Router. The DI-804HV acts as a DHCP server and will assign all
the necessary IP address information on your network. See Appendix at the end
of this Quick Installation Guide or the Manual on the CD-ROM for setting each
network adapter to automatically obtain an IP address.
Check Your Package Contents
DI-804HV VPN Router
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP/Straight Through) Cable
5V DC Power Adapter
Using a power supply
with a different voltage
rating will damage and void
the warranty of this product.
If any of the above items are missing, please contact your reseller.
© 2003 D-Link Systems, In c. All rights reserved. Trademarks or registere d trademarks are the property of their respecti ve holders. Software and
specifications subject to change without notice. DI-804HV. 02212003
1
Connecting The DI-804HV VPN Router To
Your Network
A.
First, connect the power adapter to the receptor at the back panel of the
DI-804HV and then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B.
1. Power off your Cable or DSL modem; some devices may not have a on/
off switch and will require you to unplug the power adapter. Now, the DI-804HV
should be powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off) – DI-804HV (Power On)
Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL
modem. After the Ethernet cable is securely connected, power on the Cable /
DSL modem by turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (Power On) – DI-804HV (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on the back panel
of the DI-804HV. The WAN LED light will illuminate to indicate proper
connection. If the WAN LED is not illuminated, please go back and step B and
repeat its instructions.
C.
D.
Insert an Ethernet cable to LAN port 1 on the back panel of the DI-804HV
and an available Ethernet port on the network adapter in the computer you will
use to configure the DI-804HV. The LED light for LAN Port 1 will illuminate to
indicate proper connection. (Note: The LAN Ports on the DI-804HV are AutoMDI/MDIX. Meaning you can use a straight-through or crossover-Ethernet cable
to the LAN Ports.)
COM Port for dial-up Internet connection.
C. LAN PORTS These are the connections for
Ethernet cables to Ethernet enabled computers.
D. COM Port Used to
connect to an external
dial-up modem.
B. WAN PORT This is
for the connection of an
Ethernet cable to the
Cable or DSL modem
Reset Button
Pressing this button restores
the Router to its original factory
default settings.
2
A. Receptor for
Power Adapter.
Restart Your Computer
Connecting Additional Computers To
The DI-804HV
Using additional Ethernet (CAT5 UTP) cables, connect your
Ethernet-equipped computers to the remaining Ethernet LAN ports
on the back panel of the DI-804HV.
M1 LED – will flash
consistently to indicate
that the DI-804HV is
working properly.
POWER LED – a solid
light indicates a proper
connection to the
power supply.
WAN LED – a
solid light indicates
connection on the
WAN port. This
LED blinks during
data transmission.
M2 LED – a solid light
indicates that Internet
connection has been
established.
3
COM LED – a solid
light indicates a proper
connection to a dial-up
modem.
LOCAL NETWORK
LEDs – a solid light
on the port indicates a
connection to an
Ethernet enabled
computer on ports 1-4.
This LED blinks during
data transmission.
When you have completed the steps in this Quick Installation
Guide, your connected network should look similar to this:
Using The Setup Wizard
Open your W eb browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
The logon pop-up screen will appear.
Type “admin” for the username and
leave the password field blank.
Click OK
4
The Setup Wizard (continued)
Once you have logged in, the
Home screen will appear.
Click Run W izard
You will see the following screens
Click Next
Set up your new password.
You have the option to
establish a password.
Click Next
5
The Setup Wizard (continued)
Choose your time zone from
the drop down list.
Click Next
Select your Internet
Connection. You will be
prompted to select the type of
Internet connection for your
router.
If you are unsure of which setting to select,
please contact your Internet Service Provider.
Click Next
Select Others only if you use PPTP in Europe or Big
Pond Cable in Australia.
6
The Setup Wizard (continued)
If you selected Dynamic IP
Address, this screen will appear:
(Used mainly for Cable Internet
service.)
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network adapter
in your computer. You can also
manually type in the MAC address.
W hat is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already
include built-in network adapters.
Click Next
If your ISP requires a Static IP
Address, and this option is
selected, then this screen will
appear:
Enter the IP address information
originally provided to you by your
ISP. You will need to complete
all the required fields.
Click Next
7
The Setup Wizard (continued)
If your ISP uses PPPoE
(Point-to-Point Protocol over
Ethernet), and this option is
selected, then this screen will
appear: (Used mainly for DSL
Internet service.)
Please be sure to remove
any existing PPPoE client
software installed on your
computers.
Enter in the username and
password provided to you by
your ISP.
Click Next
Configure this section only if
you have an analog dial-up
account. Otherwise click Next
to skip.
Click Next
8
Your Setup is Complete!
Click Restart
Test Internet Connection.
You will be returned to the Home tab.
Click to Exit
Then relaunch your
Web browser (i.e.,
Internet Explorer or
Netscape Navigator),
to link to your favorite
Web site to test your
Internet connection.
For additional settings
or information, refer to
the Advanced, Tools,
or Status tabs on the
web-management
interface; or to the
Manual located on the
CD.
9
APPENDIX (continued)
To connect to the network, make sure the network adapter in your computer is
configured properly. Here’s how to configure the network adapter to obtain an IP
address automatically for the DI-804HV Broadband Router.
For Microsoft Windows XP:
Go to Start > right click on
My Network Places >
select Properties > Double-click on
the Network Connection associated
with the Ethernet adapter
(i.e., D-Link DFE-530TX+).
Click Internet Protocol (TCP/IP)
Click Properties
Select Obtain an IP address
automatically
Click OK
Restart your
computer
10
For Apple Macintosh OS X:
Go to the Apple Menu Click
on Network and Select
System Preferences
Click on
Network
Select Built-in Ethernet
in the show pull down
menu
Select Using DHCP in
the Configure pull down
menu
Click on Apply Now
The IP address information,
the Subnet Mask, the Router’s
IP address and the Ethernet
adapter address will appear
11
Technical Support
You can find the most recent software and user documentation on the D-Link
website.
D-Link provides free technical support for customers within the United States
for the duration of the warranty period on this product.
U.S. customers can contact D-Link technical support through our website or
by phone.
D-Link Technical Support over the Telephone:
(877) 453-5465
24 hours a day, seven days a week
D-Link Technical Support over the Internet:
http://support.dlink.com
12
Download PDF

advertising