Owner`s manual | D-Link DIR-826L Router User Manual

LCD TV
OWNER’S MANUAL
LCD TV MODELS
42LBX
47LBX
52LBX
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).
As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the
ENERGY STAR guidelines
for energy efficiency.
www.lgusa.com / www.lg.ca
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
FCC NOTICE
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
1
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.
This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At the
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be
placed immediately adjacent to that safety instruction:
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
1
Do not use this apparatus near water.
2
Clean only with dry cloth.
3
4
2
5
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
6
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
7
Only use attachments/accessories specified by
the manufacturer.
8
Unplug this apparatus when unused for long
periods of time.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
9
10
Never touch this apparatus or antenna during
a thunder or lighting storm.
11
Do not allow a impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
12
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has exposed to rain or moisture,
does not operate normally, or has been
dropped.
13
of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use
14
Outdoor use marking :
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain
or moisture.
15
Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.
16
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock. If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
17
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
3
CONTENTS
MEDIAHOST
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MEDIAHOST
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Attaching the TV to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . . 11
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
USB In Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Audio Out Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
WATCHING TV / CHANNEL CONTROL
Remote Contro Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
- Add / Delete Channel (Manual Tuning) . . . . . . 33
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SimpLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 46
Preset Picture Settings
- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Manual Picture Adjustment
- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 49
- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
XD - Picture Improvement Technology . . . . . . . . . . . . . 51
Advanced - Cinema 3:2 Pulldown Mode . . . . . . . . . . . 52
Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 53
Advanced - TruM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
TruM Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 57
Preset Sound Setting (Sound Mode) . . . . . . . . . . . . . . . . 58
Sound Setting Adjustment - User Mode . . . . . . . . . . . 59
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 61
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
On-Screen Menus Language Selection . . . . . . . . . . . . . 64
Caption Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
- Analog Broadcasting System Captions . . . . . . . 66
- Digital Broadcasting System Captions . . . . . . . . 67
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Sleep Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Programming the Remote Control . . . . . . . . . . . . . . . . . . . 85
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
External Control Through RS-232C . . . . . . . . . . . . . . . . . .91
5
FEATURES OF THIS TV
R
R
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
TruSurround XT
TruSurround XT
PREPARATION
LG TV with this logo displays Full HD(high-definition) 1080p native resolution by receiving and processing a Full HD 1080p signal.
LG TV with this logo can play MP3 music from a
MP3 player, such as iPOD, and JPEG images from a
digital camera through the USB device.
With HDMI CEC support of LG’s audio/video device
connected to the HDMI (high-definition multimedia
interface), LG TV with this logo works easily with one
remote control.
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.
LG's own special digital image generator, consisting
of a full digital image processor, six different main
picture quality factors.
It has three HDMI ports that connect audio and
video devices with one cable and produces the highest quality digital images and sound.
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.
■ Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.
■ Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
■
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.
c. Disposal of this product must be carried out in accordance to the regulations of your local authority.
6
PREPARATION
ACCESSORIES
TV INPUT
STB
BRIGHT
-
MENU
BRIGHT
+
PREPARATION
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please
contact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
INK
TIMER
RATIO
SIMPL
1.5V
LCD TV PLASMA TV
1.5V
Owner's Manual
BACK
http://www.lgusa.com
www.lg.ca
APM
Copyright© 2007 LGE,
All Rights Reserved.
Owner’s Manual
CC
AUTO DEMO M/C EJECT
Remote Control
CD Manual
■
Batteries
Slightly wipe stained spot on the exterior only with the polishing
cloth for the product exterior if there is stain or fingerprint on
surface of the exterior.
■
Power Cord
Polishing Cloth
Do not wipe roughly when removing stain. Please be cautions of
that excessive power may cause scratch or discoloration.
Option Extras
Cable Management
75ohm Round Cable
D-sub 15 pin Cable
This feature is not available for all models.
2- TV Bracket Bolts
(Refer to p.10)
2- TV Brackets,
2- Wall Brackets
(Refer to p.10)
Twist Holder
Arrange the wires with the
twist holder.
7
PREPARATION
FRONT PANEL INFORMATION
PREPARATION
■
Here shown may be somewhat different from your TV.
■
NOTE: If your product has a protection tape attached, remove the tape.
And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).
CH
CH
CHANNELVOL
(D,E) Buttons CH
VOL
VOLUME
(F,G) Buttons
VOL
INPUT Button
/I
8
MENU Button
INPUT
Power/Standby Indicator
• Illuminates red in standby mode.
• Illuminates green when the set is switched on.
MENU
Intelligent Eye
Adjusts picture according to
the surrounding conditions.
ENTER
Remote Control Sensor
ENTER Button
POWER Button
BACK PANEL INFORMATION
Here shown may be somewhat different from your TV.
PREPARATION
USB IN
■
USB Input port
R
VIDEO L/MONO AUDIO
A
S-VIDEO
6
AV IN 2
10
3
1
RGB
/DVI
ANTENNA/
CABLE IN
9
ANTENNA/
CABLE IN
5
RGB
/DVI
4
8
7
6
2
1
HDMI/DVI IN
Connect a HDMI signal to 1, 2 or 3.
Or DVI (VIDEO)signal to the 1, 2 or 3 port with a
DVI to HDMI cable.
2
COMPONENT IN
Connect a component video/audio device to these
jacks.
3
RGB(PC)
AUDIO (RGB/DVI)
Connect the monitor output from a PC to the
appropriate input port.
4
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
5
REMOTE CONTROL PORT
Connect your wired remote control.
6
AV (Audio/Video) IN 1, 2
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
7
AUDIO OUT
Connect analog audio to various types of equipment.
8
DIGITAL AUDIO OUT
Connect digital audio to various types of equipment.
Note: In standby mode, these ports do not work.
9
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
10
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC power.
9
PREPARATION
ATTACHING THE TV TO A WALL
■
■
Here shown may be somewhat different from your TV.
This feature is not available for all models.
PREPARATION
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*Insert the eye-bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately ) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
10
Use a sturdy rope (not provided as parts of the product, must purchase
separately) to tie the product. It is safer to tie the rope so it becomes horizontal
between the wall and the product.
BACK COVER FOR WIRE ARRANGEMENT
■
Here shown may be somewhat different from your TV.
Connect the cables as necessary.
To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the C A B L E M A N A G E M E N T as shown.
(Insert it as pushing the loops on the both
sides of the cable management.)
PREPARATION
1
CABLE MANAGEMENT
3
Bundle the cables using the supplied twist
holder.
(This feature is not available for all models.)
TWIST HOLDER
How to remove the cable management
Hold the C A B L E M A N A G E M E N T with both
hands and pull it out.
(Pull it out as holding the loops on the both sides of
the cable management.)
NOTE
G Do not hold the CABLE MANAGEMENT when moving the product.
- If the product is dropped, you may be injured or the product may be broken.
11
PREPARATION
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4inches on all four sides from the wall.
PREPARATION
4 inches
4 inches
4 inches
4 inches
VESA WALL MOUNTING
This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.
42/47 inches: 600mm
52 inches: 800mm
400mm
NOTE
G
12
ANTENNA/
CABLE INinformation, refer to the VESA
Screw length needed depends on the wall mount used. For further
RGB
Wall Mounting Instruction Guide.
/DVI
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
PREPARATION
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall
Antenna
Socket
ANTENNA/
CABLE IN
ANTENNA/
CABLE IN
RGB
/DVI
RGB
/DVI
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the bronze wire
when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RGB
/DVI
RF Coaxial Wire (75 ohm)
ANTENNA/
CABLE IN
UHF
RGB
Antenna
/DVI
Signal
Amplifier
VHF
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
NOTE
G
The TV will let you know when the analog, cable, and digital channel scans are complete.
13
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you
do receive digital signals from a digital set-top box or other digital external device, refer to the figure as
shown below.
This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents.
(
EXTERNAL EQUIPMENT SETUP
When connecting Component cable
2
CONTRO
(RGB/DVI)
RS-23
(CONTROL
COMPONENT IN
1. How to connect
1
)
2
Connect the video outputs (Y, PB, PR) of the digital set
top box to the COMPONENT IN VIDEO 1 jacks on
the set. Match the jack colors
(Y = green, PB = blue, and PR = red).
1
Connect the audio output of the digital set-top box to
the COMPONENT IN AUDIO 1 jacks on the set.
S-VIDE
AUDIO
VIDEO
2
1
2. How to use
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Y
■
Select Component 1 input source with using the INPUT
button on the remote control.
■
If connected to COMPONENT IN 2 input, select
Component 2 input source.
Signal
Component 1/2
HDMI/DVI1, 2 or 3
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
PB
PR
L
R
Supported Display Specifications (Y, CB /PB, CR /PR)
Resolution
Horizontal
Frequency (KHz)
Vertical
Frequency (Hz)
720x480i
15.73
15.73
60.00
59.94
720x480p
31.47
31.47
59.94
60.00
1280x720p
45.00
44.96
60.00
59.94
1920x1080i
33.75
33.72
60.00
59.94
1920x1080p
67.50
67.432
27.00
26.97
33.75
33.71
60.00
59.939
24.00
23.94
30.00
29.97
(
14
)
(
1. How to connect
Connect the digital set-top box to H D M I / D V I I N 1,
2 or 3 jack on the set.
1
RGB IN
HDMI/DVI IN
No separated audio connection is necessary.
2
RGB(PC)
AUDIO
(RGB/DV
3
COMPONENT IN
2
2
2. How to use
(
)
Turn on the digital set-top
box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select H D M I 1, H D M I 2 or H D M I 3 input source with using
the INPUT button on the remote control.
■ If the digital set-top box player does not support Auto HDMI,
you need to set the output resolution appropriately.
■
1
1
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
VIDEO
1
Supported Display Specifications (HDMI-DTV)
Resolution
Horizontal
Frequency (KHz)
Vertical
Frequency (Hz)
720x480p
31.47
31.47
60.00
59.94
1280x720p
45.00
44.96
60.00
59.94
1920x1080i
33.75
33.72
60.00
59.94
67.50
67.432
27.00
26.97
33.75
33.71
60.00
59.939
24.00
23.94
30.00
29.97
1920x1080p
(
)
HDMI-DTV OUTPUT
15
EXTERNAL EQUIPMENT SETUP
When connecting HDMI to DVI cable
EXTERNAL EQUIPMENT SETUP
ANTENNA/
CABLE IN
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL COAXIAL
3
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
1
2
AUDIO OUT
1
AUDIO
VIDEO
(MONO)
S-VIDEO VIDEO
AUDIO
AV IN 1
2
2
1
DVI-DTV OUTPUT
L
R
1. How to connect
1
Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 or 3 jack on the set.
2
Connect the audio output of the digital set-top box to the AUDIO (RGB/DVI) jack on the set.
2. How to use
16
■
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■
Select HDMI1, HDMI2 or HDMI3 input source with using the I N P U T button on the remote control.
DVD SETUP
When connecting Component cable
1. How to connect
VI IN
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O 1 jacks on the set.
Match the jack colors
(Y = green, PB = blue, and PR = red).
REM
CONT
RS
(CONTR
COMPONENT IN
2
1
2
AUDIO
VIDEO
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the set.
2. How to use
Turn on the DVD player, insert a DVD.
■
Select Component 1 input source with using the INPUT
button on the remote control.
■
If connected to COMPONENT IN 2 input, select
Component 2 input source.
■
2
1
■
Y
PB
PR
L
S-VI
EXTERNAL EQUIPMENT SETUP
1
AUDIO
(RGB/DVI)
RGB(PC)
(
R
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
Pb
Pr
Y
B-Y
R-Y
Y
Cb
Cr
17
)
EXTERNAL EQUIPMENT SETUP
When connecting with an S-Video cable
1. How to connect
2
Connect the audio outputs of the DVD to the AUDIO
input jacks on the set.
AUDIO
S-VIDEO
L
ANTENNA/
CABLE IN
2. How to use
■
1
Select A V 1 input source with using the I N P U T button on
the remote control.
■ If connected to A V I N 2, select A V 2 input source.
Refer to the DVD player's manual for operating instructions.
2
REMOTE
CONTROL IN
Turn on the DVD player, insert a DVD.
■
■
DIGITAL AUDIO OUT
OPTICAL COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
UDIO
S-VIDEO VIDEO
(MONO)
When connecting HDMI cable
1. How to connect
1
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1, 2 or 3 jack on the set.
2
)
No separated audio( connection
is necessary.
Select HDMI1, HDMI2 or HDMI3 input source with using
the INPUT button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
■
If the DVD does not support Auto HDMI, you need to set
the output resolution appropriately.
RGB(PC)
AUD
(RGB/
3
COMPONENT
2
2
1
1
VIDEO
2. How to use
■
AUDIO
RGB IN
HDMI/DVI IN
18
R
AV IN 1
EXTERNAL EQUIPMENT SETUP
1
Connect the S-VIDEO output of the DVD to the
S-VIDEO input on the set.
1
HDMI-DVD OUTPUT
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■ If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible
on the screen.
■
(
)
ANTENNA/
CABLE IN
1
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
R
RGB IN
AUDIO
(RGB/DVI)
GB(PC)
REMOTE
CONTROL IN
DIGITAL AUDIO OUT
OPTICAL COAXIAL
Wall Jack
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
2
EXTERNAL EQUIPMENT SETUP
When connecting with an antenna
VIDEO
AUDIO
(MONO)
S-VIDEO VIDEO
AUDIO
AV IN 1
AUDIO OUT
Antenna
1. How to connect
1
Connect the RF antenna out socket of the VCR to the Antenna socket on the set.
2
Connect the antenna cable to the RF antenna in socket of the VCR.
2. How to use
■
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
■
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
(
)
19
EXTERNAL EQUIPMENT SETUP
(
)
When connecting with a RCA cable
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
VIDEO jacks between TV and VCR.
Connect the AUDIO/V
Match the jack colors (Video = yellow, Audio Left = white,
and Audio Right = red)
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
2. How to use
■
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
Select A V 1 input source with using the I N P U T button on
the remote control.
■ If connected to A V I N 2, select A V 2 input source.
VIDEO
L
R
ANTENNA/
CABLE IN
1
AUDIO
GB/DVI)
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL COAXIAL
(
■
)
RS-232C IN
(CONTROL & SERVICE)
NT IN
NOTE
AUDIO
S-VIDEO
VIDEO
(MONO)
AUDIO
AV IN 1
AUDIO OUT
If you have a mono VCR, connect the audio cable from
the VCR to the A U D I O L / M O N O jack of the set.
When connecting with an S-Video cable
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
L
R
1. How to connect
ANTENNA/
CABLE IN
N
2
Connect the audio outputs of the VCR to the AUDIO
input jacks on the set.
AUDIO
(RGB/DVI)
1
REMOTE
CONTROL IN
2
DIGITAL AUDIO
OUT
OPTICAL COAXIAL
RS-232C IN
(CONTROL & SERVICE)
ONENT IN
(
2. How to use
■
■
■
20
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
AUDIO
Select A V 1 input source with using the INPUT button on the
remote control.
CAUTION
If connected to AV IN 2, select A V 2 input source.
)
AUDIO OUT
S-VIDEO
VIDEO
(MONO)
AUDIO
AV IN 1
1
Connect the S-VIDEO output of the VCR to the S V I D E O input on the set. The picture quality is
improved; compared to normal composite (RCA cable)
input.
In the event that you connect
both Video and the S-Video
cables, only the S-Video will work.
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
When connecting D-sub 15 pin cable
A
C
1
2
Connect the RGB output of the PC to the R G B
(P C) jack on the set.
RGB IN
DVI IN
RGB(PC)
Connect the PC audio output to the AUDIO
(RGB/DVI) jack on the set.
AUDIO
(RGB/DVI)
R
CO
R
(CON
COMPONENT IN
2
1
■
Turn on the PC and the set.
■
Select RGB-PC input source with using the INPUT button
on the remote control.
AUDIO
VIDEO
2. How to use
1
S-
EXTERNAL EQUIPMENT SETUP
1. How to connect
(
)
2
NOTE
RGB OUTPUT
G
AUDIO
Check the image on your TV. There may be noise associated
with the resolution, vertical pattern, contrast or brightness in
PC mode. If noise is present, change the PC output to another
resolution, change the refresh rate to another rate or adjust
the brightness and contrast on the VIDEO menu until the
picture is clear. If the refresh rate of the PC graphic card can
not be changed, change the PC graphic card or consult the
manufacturer of the PC graphic card.
(
21
EXTERNAL EQUIPMENT SETUP
When connecting HDMI to DVI cable
ANTENNA/
CABLE IN
EXTERNAL EQUIPMENT SETUP
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL COAXIAL
3
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
1
2
AUDIO OUT
1
VIDEO
AUDIO
(MONO)
S-VIDEO VIDEO
AUDIO
AV IN 1
2
2
1
DVI-PC OUTPUT
L
R
1. How to connect
1
Connect the DVI output of the PC to the H D M I / D V I I N1 , 2 or 3 jack on the set.
(Use the HDMI to DVI cable)
2
Connect the PC audio output to the AUDIO (RGB/DVI) jack on the set.
2. How to use
■
Turn on the PC and the set
■
Select HDMI1, HDMI2 or HDMI3 input source with using the INPUT button on the remote control.
NOTE
22
G
If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.
G
If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the
best picture quality, adjust the output resolution of PC graphics card's output resolution to 1920x1080,
60Hz.
NOTES
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
G
Check the image on your TV. There may be noise
associated with the resolution, vertical pattern,
contrast or brightness in PC mode. If noise is present, change the PC output to another resolution,
change the refresh rate to another rate or adjust
the brightness and contrast on the PICTURE menu
until the picture is clear. If the refresh rate of the
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of the
PC graphic card.
G
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
G
The synchronization input form for Horizontal and
Vertical frequencies is separate.
Supported Display Specifications (RGB/HDMI-PC)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
37.861
37.500
59.94
72.80
75.00
800x600
35.156
37.879
48.077
46.875
56.25
60.31
72.18
75.00
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.870
74.893
1360x768
47.712
60.015
1280x1024
63.981
79.976
60.020
75.025
1600x1200
75.00
60.00
1920x1080
67.50
60.00
EXTERNAL EQUIPMENT SETUP
G
* RGB-PC mode only: 1280x768 (H-60.289, V-74.893)
23
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Overview
EXTERNAL EQUIPMENT SETUP
When the RGB input of the set is connected to a PC Output,
Select RGB-PC with using the I N P U T button on the remote
control.
When you change the resolution, select the proper resolution
in present input to see the best picture appearance.
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Picture Mode
: User1
Color Temperature
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
Screen
2
Press the G button and then use D or E button to
select Screen.
3
Press the G button to enter the screen adjustment
menu.
TruM Demo
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
TruM Demo
24
G
Selection ( G or ) leads you to
the screen adjustment menu.
Adjustment for screen Resolution, Position, Size, Phase, Reset
Use D or E button to select R e s o l u t i o n, Position, S i z e, or
Phase.
Resolution
Position G
Size
2
3
Press the ENTER button and then use D E F
make appropriate adjustments.
■ The P h a s e adjustment range is -16 ~ +16.
■ The S i z e adjustment range is -30 ~ +30.
G
button to
Press the ENTER button.
Initializing (Reset to original factory values)
Phase
Reset
Move
Prev
Resolution XGA (1024, 1280, 1360) isn’t
distinguished because of having
the same H/V Sync Time.
This function is you to select the
Default Sync Time.
Position This function is to adjust picture
to left/right and up/down as you
prefer.
Size
This function is to minimize any
vertical bars or stripes visible on
the screen background. And the
horizontal screen size will also
change.
Phase
This function allows you to
remove any horizontal noise and
clear or sharpen the image of characters.
EXTERNAL EQUIPMENT SETUP
1
To initialize the adjusted values.
1
Use D or E button to select Reset.
Resolution
Position
Size
2
Press the ENTER button and then use F or G button to
select Y e s.
Initialize Settings.
Phase
Reset
G
Yes
Prev
3
No
Select
OK
Press the ENTER button.
25
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
EXTERNAL EQUIPMENT SETUP
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
2. How to use
1
AV IN 2
■
Select A V 2 input source with using the
INPUT button on the remote control.
■
If connected to AV IN 1 input, select A V 1
input source.
■
S-VIDEO
R
VIDEO L/MONO AUDIO
A
1
USB IN
1. How to connect
Camcorder
L
VIDEO
R
Operate the corresponding external equipment.
Video Game Set
USB IN SETUP
The TV has a special signal output capability which allows you to hook up the second TV or monitor.
1. How to connect
Connect the USB device to the U S B I N jacks on the
side of TV.
S-VIDEO
After connecting the U S B I N jacks, you use the
VIDEO L/MONO AUDIO R
■
MEDIAHOST function. (G p .39)
MEDIAHOST
AV IN 2
26
or
L/MONO
MONO AUDIO R
VIDEO L/
2. How to use
USB IN
USB IN
1
AV
V IN 2
1
AUDIO OUT SETUP
Send the TV’s audio to external audio equipment via the Audio Output port.
AUDIO
1. How to connect
L
R
1
Connect audio outputs to the TV’s AUDIO OUT jacks.
(
2
)
1
ANTENNA/
CABLE IN
Set the “TV Speaker option - Off” in the AUDIO menu.
(G p .62). See the external audio equipment instruction
manual for operation.
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
Digital
(
1
Connect one end of the optical or coaxial cable to the
TV’s O P T I C A L or COAXIAL port of DIGITAL AUDIO
O U T.
2
Connect the other end of the optical or coaxial cable
to the digital audio input on the audio equipment.
EXTERNAL EQUIPMENT SETUP
Analog
)
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL COAXIAL
1
RS-232C IN
(CONTROL & SERVICE)
Set the “TV Speaker option - Off” in the AUDIO menu.
(G p .62). See the external audio equipment instruction
manual for operation.
AUDIO OUT
UDIO
NOTE
G
S-VIDEO VIDEO
(MONO)
AUDIO
AV IN 1
3
2
When connecting with external audio equipment, such as
amplifers or speakers, please turn the TV speakers off.
(G p .62)
CAUTION
(
G
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
G
Block the SPDIF out(optical/coaxial) about the contents
with ACP(Audio Copy Protection) function.
)
27
WATCHING TV /CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
MEDIAHOST
MEDIAHOST
mode control
buttons
■
VCR/DVD
buttons
■
TV INPUT
Controls the MEDIAHOST mode.
MEDIAHOST
Control video cassette recorders or DVD players.
STB
WATCHING TV / CHANNEL CONTROL
MEDIA HO
ST
MENU
BRIGHT +/-
Displays the main menu.
■
Adjust brightness on screen.
■
It turns to the default settings brightness by changing
T-
BRIGH
MENU
BRIGH
T
THUMBSTICK
(Up/Down/Left
Right/ENTER)
■
Navigate the on-screen menus and adjust the system
settings to your preference.
EXIT Clear all on-screen displays and return to TV viewing from
any menu.
LINK
TIMER
RATIO
SIMP
TIMER Select the amount of time before your TV turns off automatically.G p .72
RATIO Change the aspect ratio.G p .46
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the SimpLink menu appears
at the screen.
VOLUME UP Increase/decrease the sound level.
/DOWN
MUTE Switch the sound on or off.
BACK
p.30
FAV Scroll through the programmed Favorite channels.
p.34
CHANNEL Select available channels.
UP/DOWN
BACK Tune to the last channel viewed.
— (DASH)
APM
CC
NUMBER button
28
+
mode source.
Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.
AUTO DEMO M/C EJECT
STB
MEDIA HO
ST
POWER Turns your TV or any other programmed equipment on or off, depending on the mode.
TV INPUT In AV 1-2, Component 1-2, RGB-PC, HDMI1, HDMI2 and HDMI3 input sources, screen returns to
the last TV channel.
INPUT External input modes rotate in regular sequence: Antenna, Cable, AV1-2, Component 1-2, RGB-PC,
HDMI1, HDMI2, HDMI3 (Antenna, Cable, AV 1-2, Component 1-2, RGB-PC, HDMI1, HDMI2,
HDMI3 input sources are linked automatically, only if these are connected ).
MEDIAHOST
MEDIAHOST Enter to the MEDIAHOST mode.
MEDIAHOST
Inside the Sliding Cover
PICTURE Adjust the factory preset picture depend
on the viewing environment. G p. 47
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
SOUND Select the appropriate type of sound for
type of program. G p. 58
SAP Select MTS sound: Mono, Stereo, and SAP
analog mode. Change the audio language
DTV mode G p. 61
WATCHING TV / CHANNEL CONTROL
MODE Select the remote operating mode: TV, DVD, VCR, AUDIO, or STB.
* If the mode of another product is selected, a button on the remote control which is not used
for the selected product can control the TV.
CC Select the Caption On/Off. G p .65
MARK Enter the selected functions. G p .41
USB EJECT Remove the USB device. G p .39
Installing Batteries
Remote control effective range
R
TV INPUT
TV INPUT
TV INPUT
STB
■
■
■
Open the battery compartment cover on the
back side and install the batteries matching correct polarity (+with +,-with -).
Install two 1.5V AA batteries. Don’t mix old or
used batteries with new ones.
Close cover.
STB
MEDIA HOST
STB
BRIGHT
■
■
MEDIA HOST
MEDIA HOST
-
MENU
BRIGHT
+
Use a remote control up to 7 meters distance and 30
degree (left/right) within the receiving unit scope.
BACK
BACK
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
Dispose of used batteries in a recycle bin to preserve environment.
29
TV INPUT
WATCHING TV /CHANNEL CONTROL
STB
MEDIA HO
ST
TURNING ON TV
INPUT
TV INPUT
First, connect power cord correctly. At this moment, the TV switches to
standby mode.
(or POWER), INPUT, C H (D or E) but■ In standby mode, press the
P
O
W
ER, INPUT, TV INPUT, C H(D or E),
ton on the TV or press the
(
)
Number 0~9
9 button on the remote control.
1
WATCHING TV / CHANNEL CONTROL
2
Select the viewing source by using the INPUT button on the remote control.
■ This TV is programmed to remember which mode it was last set to, even
if you turn the TV off.
STB
TIMER
RATIO
MEIM
DIAPHO
ST
S
BACK
SAP
PICTURE
SOUND
MARK
USB EJECT
CC
TV INPUT
When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
3
STB
MEDIA HO
ST
BACK
NOTE
G
SOUND
MARK
USB EJECT
CC
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
CHANNEL SELECTION
1
SAP
PICTURE
TV INPUT
TV INPUT
Press the C H (D or E) or NUMBER buttons to selectMEaDIA HOchannel
number.
ST
STB
STB
MEDIA HO
ST
BACK
VOLUME ADJUSTMENT
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
Adjust the volume to suit your personal preference.
LINK
TIMER
1
Press the V O L (D or E) button to adjust the volume.
2
If you want to switch the sound off, press the M U T E button.
3
You can cancel the Mute function by pressing the MUTE or V O L (D or E)
button.
RATIO
SIMP
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
CC
SAP
PICTURE
30
MARK
USB EJECT
CC
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
1
Press the M E N U button and then use D or E button to select each menu.
2
Press the G button and then use
D E F G
PICTURE
Auto Tuning
Picture Mode
: User1
Manual Tuning
Color Temperature
: Cool
Channel Edit
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
Screen
TruM Demo
LOCK
AUDIO
For Canada
For USA
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
Sound Mode
: Off
WATCHING TV / CHANNEL CONTROL
SETUP
button to display the available menus.
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
Downloadable Rating
Input Block
Input Block
TIME
OPTION
Language
: English
Input Label
Clock
: Oct 19, 2006, 03:44 AM
Off Time
: Off
SimpLink
: Off
On Time
: Off
Key Lock
: Off
Sleep Time
: Off
Caption
: Off
Auto Sleep
: Off
Set ID
:1
31
WATCHING TV /CHANNEL CONTROL
CHANNEL SETUP
TV INPUT
TV INPUT
Auto Scan (Auto Tuning)
STB
OST
STB
WATCHING TV / CHANNEL CONTROL
K
TV INPUT
STB
MEDIA HO
ST
Automatically finds all channels
available through antenna
or cable inputs, and stores them in memory on the channel
list.
Run Auto Tuning again after any Antenna/Cable connection
changes.
A password is required to gain access to Auto Tuning menu
if the Lock System is turned on.
MEDIA HO
ST
MEDIA HO
ST
TBRIGH
MENU
BRIGH
T+
LINK
TIMER
RATIO
SIMP
Auto Tuning
1
Press the M E N U button and then use D or E button
to select the SETUP menu.
2
Press the G button and then use D or E button to
select Auto Tuning.
Manual Tuning
Channel Edit
BACK
BACK
SAP
PICTURE
MARK
3
CC
USB EJECT
BACK
PICTURE
MARK
Press the ENTER button to begin the channel search.
Allow Auto Tuning to complete the channel search
cycle for A N T E N N A and CABLE.
SOUND
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
USB EJECT
Auto Tuning
G
Manual Tuning
Channel Edit
Selection ( G or ) leads you to
the Auto Tuning screen.
NOTE
Auto Tuning
Manual Tuning
Channel Edit
Processing Auto Tuning...
Selection ( G or
) leads
DTV Ch.23
you to the Auto Tuning
Found Channel(s): 16
screen.
Analog TV antenna
Digital DTV antenna
Analog CATV cable
Digital CADTV cable
32
Press to stop the current
scan and start ANALOG
ANTENNA channel scan.
Next
MENU Prev
TV INPUT
TV IN
TV INPUT
TV INPUT
Add/Delete Channel (Manual Tuning)
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
A password is required to gain access to Manual Tuning
menu if the Lock System is turned on.
If selecting DTV or CADTV input signal, you can view the
on-screen signal strength monitor to see the quality of the
signal being received.
MENU
TBRIGH
BRIGH
T+
RATIO
LIN
SIMP
Auto Tuning
1
Press the M E N U button and then use D or E button
to select the SETUP menu.
2
Press the G button and then use D or E button to
select Manual Tuning.
Manual Tuning
Channel Edit
BACK
PICTURE
SOUND
SAP
SAP
PICTURE
MARK
BACK
CC
PICTURE
SOUND
MARK
USB EJECT
CC
USB EJECT
MARK
3
BACK
CC
USB EJECT
Press the G button and then use D or E button to
select DTV, TV, CADTV, and CATV.
Auto Tuning
Manual Tuning
Channel Edit
G
Select channel type and
RF-channel number.
DTV
4
Press the G button and then use D or E button to
select channel number you want to add or delete.
5
Press the ENTER button to add or delete for the
channel number.
WATCHING TV / CHANNEL CONTROL
K
TIMER
2
Auto Tuning
6
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Manual Tuning
Channel Edit
Select channel type and
RF-channel number.
D
E
DTV
G
12
DTV 12-0
Bad
NOTE
G
Press
Normal
Good
to delete the channel.
This digital channel number is a physical channel
number, which is different from the normal channel
number shown in Channel Edit.
33
PIC
M
WATCHING TV /CHANNEL CONTROL
TV INPUT
TV INPUT
TV INPUT
Channel Editing
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
WATCHING TV / CHANNEL CONTROL
From the default channel list created from the Auto Tuning
channel search, you can create two different types of channel lists in memory: “custom list” and “favorite channel
list”.
A custom list can be created by toggling each channel on
or off with ENTER button. The channels in the Custom List
are displayed in black and the channels deleted from the
Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to
the small window at the top-left corner of the screen.
You can create your own Favorite List. Use the F A V button
on the remote control when a channel is highlighted and
then add or delete the channel to/from your Favorite List.
TBRIGH
MENU
BRIGH
T+
LINK
TIMER
RATIO
SIMP
Auto Tuning
BACK
1
Press the M E N U button and then use D or E button
to select the SETUP menu.
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
SAP
MARK
Press the G button and then use
select C h a n n e l E d i t.
3
Press the G button. You will now see a screen filled
with channel numbers and a preview picture.
D
or
E
CC
USB EJECT
2
BACK
Channel Edit
CC
PICTURE
Manual Tuning
PICTURE
SOUND
MARK
USB EJECT
CC
button to
Auto Tuning
Manual Tuning
Channel Edit
34
4
Use D E F G button to select a channel and then
use the ENTER button to add or delete it. Press F A V
button to add the channel to the Favorite List. The
surfing icon will appear in front of that channel number.
5
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
G
Selection ( G or ) leads you to the
channel edit screen.
INPUT LIST
INPUT
TV INPUT
Press theIINPUT button to display external device that is connected to the unit, on screen.
Press the ENTER button to change the input to the active
external device. Use the D or E button to select the input
source.
AV 2
STB
MEDIA HO
ST
Input List
Antenna
T-
BRIGH
Cable
MENU
BRIGH
T+
AV 1
AV 2
Component1
E
1
2
SIMP
If all external input sources are connected:
Antenna
Cable
AV1
AV2
Component1
HDMI3
HDMI2
HDMI1
RGB-PC
Component2
PICTURE
SOUND
MARK
USB EJECT
If no external input sources are not connected:
Antenna
3
RATIO
SAP
CC
WATCHING TV / CHANNEL CONTROL
LINK
TIMER
Cable
If there is any external input source connected:
(ex: When connected only to AV 2)
Antenna
Cable
AV2
Antenna : Select it when watching the DTV/TV.
Cable: Select it when watching the CADTV/CATV.
AV 1-2 : Select it when watching the VCR or external equipment.
Component 1-2 : Select it when using the DVD or the Digital set-top box depend on connector.
RGB-PC : Select it when using PC depend on connector.
HDMI 1-3 : Select it when using DVD, PC or Digital set-top box depend on connector.
35
WATCHING TV /CHANNEL CONTROL
TV INPUT
This operates only for the devices with the
logo. Please check the
logo.
STB
This allows you to control and play other AV devices
connected to the display through HDMI cable without additional cables and settings.
MEDIA HO
ST
MENU
MENU
T-
BRIGH
BRIGH
T+
WATCHING TV / CHANNEL CONTROL
SimpLink Preparations
LINK
TIMER
1
2
Connect the HDMI/DVI IN 1, 2 or 3 terminal of the
TV to the rear terminal (HDMI output) of the
SimpLink device with the HDMI cable.
After connecting the HDMI jack for the home theater
with simpLink function in the above method, connect
the DIGITAL AUDIO OUT OPTICAL on the back of the
TV to the DIGITAL AUDIO IN terminal on the back of
the simpLink device with the Optical cable.
Language
RATIO
SIMP
: English
Input label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
Press the M E N U button and then use D or E button
to select the OPTION menu.
Language
Input label
3
Press the G button and then use
select S i m p L i n k.
D
or
E
button to
SimpLink
Key Lock
G
Off
On
Caption
Set ID
4
Press the G button and then use
select O n.
5
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
D
or
E
button to
NOTE
When operating the external device with SimpLink, press the TV button among the MODE button on
the remote control.
G When you switch the Input source with the INPUT button on the remote control, you can stop the
operation of device worked by SimpLink.
G When you select or operate the media device with home theater function, the speaker automatically
switches to home theater speaker (HT speaker).
G When you execute ‘Photo List, Music List ’function during DVD playback included in home theater supported the SimpLink stops and the applicable function is executed after switching the input to TV.
G
36
SimpLink Functions
Direct Play
After connecting AV devices to TV, you can directly control the devices and play media
without additional settings.
TV INPUT
TV INPUT
Select AV device
Enables you to select one of AV devices connected to TV and play MEit.
DIA HOST
STB
STB
Disc playback
,
,
,
,
,
,
Control connected AV devices by pressing the
,
DE F G, E N T E R buttons and buttons for play, pause, stop, fast reverse, fast forward,
chapter skip.
MEDIA HO
ST
MENU
T-
BRIGH
BRIGH
T+
TIMER
Switch audio-out
Offers an easy way to switch audio-out.
RATIO
LINK
SIMP
(A device, which is connected to TV through HDMI cable but does not support
Simplink, does not provide this function)
Note: To operate SIMPLINK, the HDMI cable with *CEC function should be used. (*CEC: Consumer
Electronics Control).
After selecting the T V button of the MODE on the remote control,
press the S I M P L I N K button.
1
BACK
BACK
SOUND
PICTURE
SAP
CC
2
Use D E F G button to select the desired device and then press
the ENTER button.
3
Control connected AV devices by pressing the
,
,
,
, DEF G, E N T E R buttons.
MARK
USB EJECT
,
,
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
WATCHING TV / CHANNEL CONTROL
Power off all devices
When you power off TV, all connected devices are turned off.(This option only applies
when the devices are stoped)
,
SimpLink Menu
1
2
3
4
5
T V v i e w i n g : Switch to the previous TV
channel regardless of the current mode.
D I S C p l a y b a c k : Select and play discs.
When multiple discs are available, the
titles of the discs are conveniently displayed at the bottom of the screen.
V C R p l a y b a c k : Play and control the
connected VCR.
H D D R e c o r d i n g s p l a y b a c k : Play and
control recordings stored in HDD.
Audio Out to HT speaker/Audio
O u t t o T V : Select HT speaker or TV
speaker for Audio Out.
1
G Selected
Device
2
3
G When no device is
connected (displayed in gray)
4
5
G When a device is
connected (displayed in
bright color)
37
WATCHING TV /CHANNEL CONTROL
INPUT LABEL
TV INPUT
TV INPUT
TV INPUT
Sets a label to each input source which is not in use when
HOST
you press INPUTMEDIAbutton.
STB
STB
STB
MEDIA HO
MENU
TBRIGH
BRIGH
T+
WATCHING TV / CHANNEL CONTROL
LINK
TIMER
Language
1
2
Press the M E N U button and then use D or E button to
select the OPTION menu.
Press the G button and then use
select Input Label.
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
5
SIMP
: English
Input label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
: 1
BACK
BACK
CC
MARK
3
RATIO
button to
SAP
PICTURE
4
38
MEDIA HO
ST
ST
CC
USB EJECT
Press the G button and then use D or E button to
select the source: AV1, AV2, Component1,
Component2, RGB-PC, HDMI1, HDMI2 or HDMI3.
Press the F or G button to select the label.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
PICTURE
SOUND
MARK
USB EJECT
CC
Language
Input label
AV1
Cable Box
SimpLink
AV2
VCR
Key Lock
Component1
DVD
Caption
Component2
Set Top Box
Set ID
RGB-PC
VCR
HDMI1
Game
G
HDMI2
Satellite
HDMI3
Cable Box
MEDIAHOST
MEDIAHOST
ENTRY MODES
When you connect a USB device or press the
displayed, automatically.
[Media Host Menu]
MEDIA HO
ST
button, this screen is
In USB device, you can not add a new folder or delete the existing folder.
1
Press the D or E button to select the desired item.
2
Press the E N T E R button to move to P h o t o L i s t or M u s i c L i s t of
USB device.
3
Press the U S B E J E C T button of remote control before removing
the USB device.
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
MEDIA HOST
BACK
NOTE
Press the USB EJECT button of remote control before removing the USB device.
Only a USB storage device is recognizable.
If the USB storage device is connected through a USB hub, the device is not recognizable.
A USB storage device using an automatic recognition program may not be recognized.
A USB storage device which uses its own driver may not be recognized.
In case of a card reader, up to four memory cards are concurrently recognizable.
The recognition speed of a USB storage device may depend on each device.
Please do not turn off the TV or unplug the USB device when the connected USB storage
device is working. When such device is suddenly separated or unplugged, the stored files or
the USB storage device may be damaged. To unplug the USB storage device, please press the
USB EJECT button on the remote control, and then unplug it safely.
Please do not connect the USB storage device which was artificially maneuvered on the PC.
The device may cause the product to malfunction or fail to be played. Never forget to use only
a USB storage device which has normal music files or image files.
Please use only a USB storage device which was formatted as a FAT or a NTFS file system provided with the Windows operating system. In case of a storage device formatted as a different
utility program which is not supported by Windows, it may not be recognized.
In case of a hard disk drive (HDD) formatted as NTFS, writing and deletion are not allowable.
Please connect power to a USB storage device which requires an external power supply. If not,
the device may not be recognized.
Please connect a USB storage device with cable is offered by USB maker. If connected with
cable is not offered by USB maker or an excessively long cable, the device may not be recognized.
Some USB storage devices may not be supported or operated smoothly.
If the name of a folder or file is too long, it will not be displayed or recognized.
39
MEDIAHOST
MEDIA
PHOTO HOST
LIST
It’s available to playback the photo file (*.jpg) in the USB device.
The On Screen Display may be different from your set. Images are
an example to assist with the TV operation.
Screen Components
MEDIA HOST
Usable USB memory
Current page/Total pages
Total number of marked
thumbnail photos
Corresponding buttons
on the remote control
40
Photo Selection and PopUp Menu
As shown, up to 15 thumbnail photos are listed per page.
E)
1
Use the C H (D or
photo page.
2
Use the M A R K button to mark or unmark a photo. When one
or more photos are marked, you can view individual photos
or a slide show of the marked photos. If no photos are
marked, you can view all photos individually or all photos in
the folder in a slide show.
3
Use D E F G button to navigate the appropriate thumbnail
photos, then press the ENTER button to show the PopUp
menu.
button to navigate in the thumbnail
MEDIA HOST
View : Display the selected item.
Mark All : Mark all photos on the screen.
Delete : Delete the selected photo item.
Cancel : Close the pop-up menu.
4
Repeatedly, press E X I T button to return to TV viewing or
press the MEDIA HOST button to return to the Media Host menu.
41
MEDIAHOST
MEDIAHOST
Set up the menu in Full-Sized Screen
You can change the settings to display photos stored on a USB
device, on a full-sized screen.
Detailed operations are available on full-sized photo view screen.
MEDIA HOST
1
Use the C H (D or E) button to navigate the thumbnail
photo page.
2
Use D E F G button to navigate the appropriate thumbnail photos, then press the ENTER button to show the
PopUp menu.
3
Use D or E button to Move to the View menu, then press
the ENTER button.
4
The selected photo is displayed in full size.
Slide Show : When no picture is selected, all photos
in the current folder are displayed during slide show.
When selected, the selected photos are displayed
during slide show. To start slide show, press ENTER
button on
.
■
Set the time interval of the slide show in Option.
■ A slide show continues for a maximum of 4 hours.
After 4 hours, the slide show will end and go to TV
mode or external input mode.
B G M : Listen to music while viewing photos in full size.
To start BGM, press ENTER button on
.
■ Set the BGM device and album in O p t i o n .
(Rotate) : Rotate photos.
Rotates the photo 90°, 180°, 270°, 360° clock(Rotate).
wise upon ENTER button on
Delete: Delete photos. Use F or G button to select
Delete and press ENTER button.
■
42
The aspect ratio of a photo may change the size of
the photo displayed on the screen in full size.
5
Use F G button to select the previous or next photo.
Use D E F G button to select and control the menu on
the full-sized screen.
6
Use E X I T button to go back to the photo list from the fullsized screen.
7
Repeatedly, press E X I T button to return to TV viewing or
press MEDIA HOST button to return to the Media Host menu.
MEDIA HOST
Option : Set values for Slide Speed and Music folde r. Use F or Gbutton to select Option and press
ENTER button.
■ Use F or G button and E N T E R button to set values. Then go to
and press ENTER to save the
settings.
■ You cannot change M u s i c F o l d e r while BGM is
playing.
Hide : Hide the menu on the full-sized screen. Use F
or G button to select H i d e and press ENTER button.
■ To see the menu again on the full-sized screen,
press ENTER button to display.
NOTE
If it is Progressive JPEG format, some photos may be not decorded.
43
MEDIAHOST
HOST
MEDIA
MUSIC LIST
TV INPUT
TV INPUT
TV INPUT
Purchased music files (*.MP3) may contain copyright restrictions.
Playback of MEthese
files may not be supportedMEDIAby
HOST this model.
DIA HOST
Music file on your USB device can be played by this unit.
STB
STB
STB
TV IN
TV INPUT
MEDIA HO
The On Screen Display may be different from your set. Images
are an example to assist with the TV operation.
STB
ST
TBRIGH
MENU
TIMER
BRIGH
T
RATIO
+
L
SIMP
INK
MEDIA HOST
Screen Components
BACK
SOUND
PICTURE
SOUND
MARK
USB EJECT
BACK
BACK
Usable USB memory
SAP
CC
PICTURE
SOUND
SAP
MARK
USB EJECT
Current page/Total pages
Total number of marked musics
Current playing time/Total playing time
Corresponding buttons
on the remote control
44
MEDIA HO
ST
MARK
SAP
BACK
CC
PICTURE
SOUND
MARK
USB EJECT
USB EJECT
SAP
CC
PIC
M
Music Selection and PopUp Menu
As shown , up to 8 music titles are listed per page.
1
2
Use M A R K button to mark or unmark a music. When one or
more music files are marked, the marked musics will be played
in sequence. For example, if you want to listen to only one
music repeatedly, just mark the music only and play it. If no
music is marked, all the music in the folder will be played in
sequence.
Use D E button to navigate the appropriate musics, then
press the ENTER button to show up the pop-up menu.
Play (During stop) : Play the selected musics.
Once a music finishes playing, the next selected one
will be played. When there are no selected musics to
play, the next one in the current folder will be played.
If you go to a different folder and press the ENTER
button, the current m usic in playback will stop.
Stop Play (During playback) : Stop the playing musics.
Play With Photo: Start playing the selected musics
and then move to the Photo List.
Mark All : Mark all musics in the folder.
Delete : Delete the selected musics.
Cancel : Close the pop-up menu.
4
MEDIA HOST
3
Use the C H (D or E) button to navigate in the music titles
page.
Repeatedly, press E X I T button to return to TV viewing or
press MEDIA HOST button to return to the Media Host menu.
■
If you don't press any button for a while during the playing,
the play information box (as shown in the below) will float
as a screen saver.
■ The ‘Screen Saver’?
Screen saver is to prevent screen pixel damage due to an
fixed image remaining on the screen for a extended period
of time.
NOTE
When music is playing,
is displayed in front of the music title.
A damaged or corrupted music
does not play but displays 00:00
in playtime.
A music downloaded from a paid
service with copyright protection
does not start but displays inappropriate information in playtime.
, EXIT
If you press ENTER,
buttons, screen saver is stopped.
,
,
,
,
The
buttons on the remote control are
also available in this mode.
45
TV INPUT
B
MEDIA HO
PICTURE CONTROL
STB
ST
TV INPUT
TV INPUT
MEDIA HO
STB
ST
MEDIA HO
TV INPUT
STB
MEDIA HO
ST
STB
ST
ST
PICTURE SIZE (ASPECT RATIO) CONTROL
T
BRIGH
This feature lets you choose the way an analog picture with a 4:3 aspect ratio
is displayed on your TV. When you receive an analog picture with a 4:3 aspect
ratio on your 16:9 TV, you need to specify how the picture is to be displayed.
■ RGB-PC input source use 4:3 or 16:9 aspect ratio.
1
BACK
PICTURE
CC
SOUND
MENU
TIMER
BRIGH
T+
RATIO
PICTURE
MARK
SOUND
CC
SAP
SIMP
LINK
MARK
MARK
USB EJECT
Selects the proper picture proportion to match
the source’s image.
PICTURE CONTROL
4:3)
(16:9
PICTURE
SOUND
SAP
CC
16:9)
USB EJECT
4:3
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
16:9
MARK
USB EJECT
SAP
CC
Zoom 2
Choose Zoom 2 when you want the picture to
be altered, both vertically extended and
cropped. The picture taking a halfway trade off
between alteration and screen coverage.
Zoom 2
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
SOUND
Zoom 1
4:3
16:9
PICTURE
Choose Zoom 1 when you want to view the
picture without any alteration. However, the top
and bottom portions of the picture will be
cropped.
Set By Program
Set By Program
BACK
Zoom 1
USB EJECT
(4:3
BACK
BACK
CC
SAP
Set by program
46
-
Press the RATIO button repeatedly to select the desired picture format.
You can also adjust Aspect Ratio in the PICTURE menu.
BACK
SAP
MEDIA HO
BACK
BACK
BACK
SAP
CC
BACK
PRESET PICTURE SETTINGS
PICTURE
SOUND
PICTURE
PICTURE
SOUND
MARK
MARK
MARK
USB EJECT
SOUND
SAP
PICTURE
CC
MARK
USB EJECT
USB EJECT
USB EJECT
Picture Mode -Preset
Picture Mode adjusts the TV for the best picture appearance.
Select the preset value in the Picture Mode menu based on the
program category.
Intelligent Eye, Dynamic, Standard, M i l d Settings are preset for
optimum picture quality at the factory and are not adjustable.
In the U s e r 1, and U s e r 2 modes only, user can directly adjust
the contrast, brightness, color, sharpness, tint.
2
■
Press the PICTURE button repeatedly to select the picture
appearance setup option as shown below :
Intelligent Eye, Dynamic, Standard, M i l d, User1, and
User2 (your own settings).
PICTURE CONTROL
1
Press the E X I T button to save and return to TV viewing.
You can also use the PICTURE menu to adjust Picture Mode.
Picture Mode
: User1
Picture Mode
Color Temperature
: Cool
Color Temperature
Dynamic
XD
XD
Standard
Advanced
Advanced
Mild
Aspect Ratio
User 1
Picture Reset
Picture Reset
User 2
Screen
Screen
TruM Demo
TruM Demo
Aspect Ratio
: 16:9
SO
SAP
CC
G
Intelligent Eye
47
USB
PICTURE CONTROL
TV INPUT
TV INPUT
TV INPUT
Color Tone -Preset
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
Choose one of three automatic color adjustments. Set to
warm to enhance hotter colors such as red, or set to cool to
see less intense colors with more blue.
When selecting Picture Mode options (Dynamic, Standard
and Mild), Color Temperature is automatically change.
When selecting Picture Mode options (User 1 and User 2),
you can choose the Color Temperature.
T-
BRIGH
MENU
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use
to select the PICTURE menu.
D
or E button
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
XD
Advanced
PICTURE CONTROL
Aspect Ratio
2
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
BACK
TruM Demo
CC
MARK
3
Screen
Press the G button and then use D or E button to
select Color Temperature.
SAP
PICTURE
4
CC
USB EJECT
Press the G button and then use D or E button to
select either Cool, Medium, Warm or U s e r.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
PICTURE
SOUND
MARK
USB EJECT
Picture Mode
Color Temperature G
Cool
XD
Medium
Advanced
Warm
Aspect Ratio
User
Picture Reset
Screen
TruM Demo
48
: 16:9
Picture Reset
CC
TV INPUT
TV INP
TV INPUT
STB
MEDIA HO
ST
TV INPUT
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MANUAL PICTURE ADJUSTMENT
MENU
T-
BRIGH
Picture Mode -User Mode
BRIGH
T+
Adjust the picture appearance to suit your preference and
viewing situations.
LINK
TIMER
Picture Mode
: User1
Color Temperature
: Cool
SIMP
RATIO
XD
Advanced
BACK
1
Press the M E N U button and then use D or E button to
select the PICTURE menu.
PICTURE
SOUND
SAP
Aspect Ratio
: 16:9
BACK
CC
SAP
PICTURE
MARK
BACK
Picture Reset
PICTURE
SOUND
MARK
USB EJECT
CC
MA
Screen
USB EJECT
MARK
PICT
CC
USB EJECT
PICTURE CONTROL
TruM Demo
2
3
Press the G button and then use
select Picture Mode.
Press the G button and then use
select User 1 or User 2.
D
D
or
or
E
E
button to
button to
Picture Mode
Intelligent Eye
Color Temperature
Dynamic
XD
Standard
Advanced
Mild
Aspect Ratio
User 1
Picture Reset
User 2
G
Screen
4
Press the G button and then use D or E button to
select the desired picture option ( C o n t r a s t ,
Brightness, Color, Sharpness,Tint or Back Light).
■
5
[ B a c k L i g h t ] To control the brightness of screen,
adjust the brightness of LCD panel.
Press the G button and then use
make appropriate adjustments.
F
or
G
button to
TruM Demo
User1
Contrast
85
Brightness
50
Color
50
Sharpness
50
Tint
MENU
G
R
G
100
to confirm.
E
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
0
Back Light
Press
6
Selection ( G or ) leads you to
the detailed setting screen.
Contrast
85
E
49
TV INPUT
TV INPUT
TV INPUT
PICTURE CONTROL
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
Color Tone -User Mode
LINK
You can also adjust the detailed settings(Red, Green, Blue)
by selecting the U s e r menu.
This feature operate only if the picture mode set User 1 or
User 2.
TIMER
RATIO
SIMP
BACK
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
SAP
PICTURE
1
BACK
Picture Mode
CC
Press the M E N U button and then use
to select the PICTURE menu.
MARK
D
USB EJECT
or E button
CC
: User1
Color Temperature
XD
PICTURE
SOUND
MARK
USB EJECT
: Cool
CC
Advanced
Aspect Ratio
: 16:9
PICTURE CONTROL
Picture Reset
Screen
TruM Demo
2
Press the G button and then use
select Color Temperature.
D
or E button to
Picture Mode
3
Press the G button and then use
select U s e r.
D
or E button to
Color Temperature
Cool
XD
Medium
Advanced
Warm
Aspect Ratio
User
G
Picture Reset
4
Press the G button and then use
select R e d, Green, or B l u e.
D
5
Press the G button and then use
make appropriate adjustments.
F
■
or E button to
or G button to
The adjustment range of R e d, G r e e n, or B l u e
is -20~ +20.
Screen
TruM Demo
User
Red
0
Green
0
Blue
0
Press
6
Selection ( G or ) leads you to
the detailed setting screen.
MENU
to confirm.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
E
Red
E
50
0
G
XD - PICTURE IMPROVEMENT TECHNOLOGY
TV INPUT
TV INPUT
TV INPU
TV INPUT
XD is LG Electronics unique picture improving technology to
MEDIA HO
ST
display a real HD source
through an digital signal processing algorithm.
When selecting Picture Mode options (Dynamic, Standard
and Mild), XD is automatically change to Auto.
When selecting Picture Mode options (User 1 and User 2),
you can choose the Auto / Manual and when selecting
Manual, you can adjust the XD Contrast, XD color and XD
Noise.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button to
select the PICTURE menu.
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
Advanced
Press the G button and then use
select X D.
BACK
2
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
button to
CC
MARK
Press the G button and then use
select Auto or Manual.
Aspect Ratio
: 16:9
BACK
Picture Reset
SAP
PICTURE
3
BACK
F
or
G
USB EJECT
CC
Screen
TruM Demo
PICTURE
SOUND
MARK
USB EJECT
CC
button to
* Selecting the Manual
1. Press the E button and then use D or E button to
select XD Contrast, XD Color or XD Noise .
X D C o n t r a s t : Optimizing the contrast automatically according to the brightness of the reflection.
■ X D C o l o r : Adjusting the colors of the reflection
automatically to reproduce as closely as possible to
the natural colors.
■ X D N o i s e : Removing the noise up to the point
where it does not damage the original picture.
■
PICTURE CONTROL
XD
Picture Mode
Color Temperature
XD
G
Manual
Advanced
Aspect Ratio
XD Contrast On
Picture Reset
XD Color
On
Screen
XD Noise
On
TruM Demo
2. Use the F or G button to select O n or O f f.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
51
PICTUR
MARK
PICTURE CONTROL
ADVANCED -CINEMA 3:2 PULLDOWN MODE
TV INPUT
TV INPUT
TV INPUT
Set up the TV for the best picture appearance for viewing
MEDIA HO
ST
movies.
This feature is disable only in RGB-PC, HDMI1, HDMI2,
HDMI3 or Component1,2(except 480i) mode.
When you operate Cinema (3:2 Pull-Down Mode or Cinema
Correction Mode), the TV will adjust 24 fps video from
movies to 30 fps video for display (This function is only
available in TV(Analog, DTV), AV1, AV2, Component 480i
mode.)
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use
to select the PICTURE menu.
D
or
E
button
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
XD
Advanced
PICTURE CONTROL
Aspect Ratio
: 16:9
Picture Reset
Press the G button and then use
select Advanced.
BACK
2
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
button to
BACK
TruM Demo
CC
SAP
PICTURE
MARK
3
Screen
BACK
Press the G button and then use
select Cinema 3:2 Mode.
D
or
E
CC
PICTURE
SOUND
MARK
USB EJECT
USB EJECT
CC
button to
Picture Mode
Color Temperature
XD
4
Use the F or G button to select O n or O f f.
Advanced
5
52
Cinema 3:2 Mode
Off
Black Level
Low
Picture Reset
TruM
Low
Screen
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
G
Aspect Ratio
TruM Demo
ADVANCED - BLACK (DARKNESS) LEVEL
TV INPUT
TV INP
TV INPUT
TV INPUT
Adjusting the contrast and the brightness of the screen
ME HO
ST
using the black levelDIAof
the screen.
This feature operates only in HDMI1, HDMI2, HDMI3, AV1,
or AV2 mode.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
RATIO
SIMP
Press the M E N U button and then use D or E button
to select the PICTURE menu.
: User1
Color Temperature
: Cool
PICTURE CONTROL
Press the G button and then use D or E button to
select Advanced.
Picture Mode
BACK
2
PICTURE
SOUND
SAP
XD
BACK
Advanced
CC
PICTURE
MARK
BACK
SAP
CC
PICTURE
Aspect Ratio
USB EJECT
MARK
USB EJECT
Picture Reset
SOUND
CC
: 16:9
MARK
USB EJECT
Screen
3
4
Press the G button and then use D or E button to
select Black level.
Use the
F
TruM Demo
or G button to select L o w, or H i g h.
Picture Mode
Color Temperature
■
■
5
Low
The reflection of the screen gets darker.
XD
Aspect Ratio
Black Level
Low
High
The reflection of the screen gets brighter.
Picture Reset
TruM
Low
Advanced
G
Cinema 3:2 Mode
Off
Screen
TruM Demo
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
53
PICTU
MAR
PICTURE CONTROL
ADVANCED - TruM
TV INPUT
TV INPUT
TV INPUT
Set up the TV for best picture with film judder cancellation
MEDIA HO
ST
that provides stunningly
steady movements.
This feature is disable in RGB-PC, HDMI-PC mode.
And when HDMI is set to the PC in I n p u t L a b e l, T r u M is
also disable.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use
to select the PICTURE menu.
D
or
E
button
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
XD
Advanced
PICTURE CONTROL
Aspect Ratio
: 16:9
Picture Reset
Press the G button and then use
select Advanced.
BACK
2
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
button to
Press the G button and then use
select T r u M.
Screen
BACK
TruM Demo
SAP
PICTURE
MARK
3
BACK
CC
D
or
E
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
CC
button to
Picture Mode
Color Temperature
4
XD
Use the F or G button to select O f f, L o w, or H i g h.
Low
Set amount of film judder to low.
■ High
Set amount of film judder to high.
■
* If you have some problem in viewing picture, set T r u M
to L o w or O f f.
5
54
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Advanced
G
Cinema 3:2 Mode
Off
Aspect Ratio
Black Level
Low
Picture Reset
TruM
High
Screen
TruM Demo
TruM DEMO
TV INPUT
TV INPU
TV INPUT
TV INPUT
Use it to see the difference between TruM Demo on and
MEDIA HO
ST
TruM Demo off.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
XD
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select TruM Demo.
BACK
PICTURE
SOUND
SAP
PICTURE
MARK
BACK
TruM Demo
SAP
CC
PICTURE
SOUND
MARK
USB EJECT
CC
USB EJECT
MARK
3
Screen
BACK
CC
USB EJECT
Press the G button to begin TruM Demo.
PICTURE CONTROL
Advanced
Picture Mode
Color Temperature
4
To stop TruM Demo, press the E X I T button.
XD
Advanced
Aspect Ratio
Picture Reset
Screen
TruM Demo
G Selection ( G or
) leads you to the
TruM Demo.
• TruM Demo
TruM On
TruM Off
55
PICTUR
MARK
PICTURE CONTROL
PICTURE RESET
TV INPUT
TV INPUT
TV INPUT
Use to quickly reset all the Picture menu options to their
MEDIA HO
ST
original factory preset
values.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Picture Mode
: User1
Color Temperature
: Cool
RATIO
SIMP
XD
Advanced
PICTURE CONTROL
Aspect Ratio
: 16:9
Picture Reset
Press the G button and then use D or E button to
select Picture Reset.
Screen
BACK
2
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
TruM Demo
CC
PICTURE
MARK
3
BACK
SAP
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
CC
Press the G button to reset the Picture menu options
to original values.
Picture Mode
Color Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
TruM Demo
56
G Selection ( G or ) resets to the
factory settings(defaults).
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER (AUTO VOLUME)
TV INPUT
TV INPU
TV INPUT
TV INPUT
Scans for changes in sound levels during commercials, then
ME
adjusts the sound toDIA HOSTmatch the specified audio level. Auto
Volume makes sure that the volume level remains consistent
whether you are watching a commercial or a regular TV program.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Sound Mode
Press the M E N U button and then use D or E button
to select the AUDIO menu.
Press the G button and then use D or E button to
select Auto Volume.
RATIO
SIMP
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
PICTURE
MARK
3
BACK
BACK
CC
SAP
CC
USB EJECT
Press the G button and then use D or E button to
select O n or O f f.
Balance
4
SOUND
MARK
USB EJECT
Sound Mode
Auto Volume
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
PICTURE
TV Speaker
G
Off
On
CC
SOUND & LANGUAGE CONTROL
2
57
PICTU
MAR
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS (SOUND MODE)
Sound Mode lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the
program content.
Standard, Music, Movie, Sports and User are preset for good sound
quality at the factory and are not adjustable.
BACK
1
SOUND & LANGUAGE CONTROL
58
2
■
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
CC
PICTURE
SOUND
MARK
USB EJECT
Press the SOUND button repeatedly to select the appropriate
sound setup as shown below:
S t a n d a r d, M u s i c, M o v i e, S p o r t s and User (your own settings).
Press EXIT button to return to TV viewing .
You can also adjust Sound Mode in the AUDIO menu.
Sound Mode
: Standard
Sound Mode
Auto Volume
: On
Auto Volume
Balance
:0
Balance
TV Speaker
: On
TV Speaker
G
Standard
Music
Movie
Sports
User
SAP
CC
SOUND SETTING ADJUSTMENT - USER MODE
TV INPUT
TV INP
TV INPUT
TV INPUT
Adjust the sound to suit your taste and room situations.
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
1
Press the M E N U button and then use
to select the A U D I O menu.
D
or
E
button
T-
BRIGH
2
Press the G button and then use
select S o u n d M o d e.
D
or
E
MENU
BRIGH
T+
button to
LINK
TIMER
3
Press the G button and then use
select U s e r.
D
or
E
MARK
USB EJECT
SAP
BACK
TV Speaker
MARK
SAP
Press the G button and then use
make appropriate adjustments.
F
or
G
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
CC
Selection ( G or ) leads you to
the detailed setting screen.
button to
Selecting the Front surround
Press the G button and then use F or G button to
select O f f, 3 D E c h o S o u n d S y s t e m or S R S (Sound
Retrieval System) T r u S u r r o u n d X T.
User
Treble
50
Bass
50
Front Surround
6
G
BACK
CC
PICTURE
5
Balance
BACK
SOUND
Standard
Music
Movie
Sports
User
Auto Volume
G
Off
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Press
SRS TruSurround XT
Takes advantage of any multi-channel format without
needing to add extra speakers or equipment. Dialog clarity,
bass enrichment, and the addition of stereo audio
enhancement produces an immersive sound experience
from standard stereo material.
MENU
SOUND & LANGUAGE CONTROL
Press the G button and then use D or E button to
T r e b l e, B a s s, or
select the desired sound option (T
F r o n t S u r r o u n d).
PICTURE
SIMP
button to
Sound Mode
4
RATIO
to confirm.
Front Surround
3D EchoSound System
3D EchoSound System
Creates a stunning simulated stereo effect from any mono
sound and a realistic three-dimensional sound with a very
wide and deep sound stage.
59
PICT
MA
SOUND & LANGUAGE CONTROL
BALANCE
TV INPUT
TV INPUT
TV INPUT
Adjust the left/right sound of speaker to suit your taste and
MEDIA HO
ST
room situations.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
SOUND & LANGUAGE CONTROL
2
Press the M E N U button and then use D or E button to
select the AUDIO menu.
Press the G button and then use
select Balance.
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
button to
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
BACK
BACK
Press the G button and then use
make appropriate adjustments.
SAP
PICTURE
F
or
G
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
CC
button to
Sound Mode
Auto Volume
Balance
0
L
R
0
L
R
TV Speaker
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Balance
60
SIMP
CC
MARK
3
Sound Mode
RATIO
STEREO/SAP BROADCAST SETUP
This TV can receive MTS stereo programs and any SAP
(Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal as well as
the original one and when you select Stereo or SAP on the
remote control.
Mono sound is automatically received if the broadcast is only in
Mono; even though Stereo or SAP has been selected.
Select Mono if you want to listen to the mono sound in remote
areas during stereo/SAP broadcasting.
Stereo or SAP can be received in Analog channel.
BACK
BACK
PICTURE
SOUND
SAP
SAP
PICTURE
MARK
PICTU
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
MAR
If other languages available on the digital signal, select
them with the S A P button.
Press E X I T button to save and return to TV viewing.
SOUND & LANGUAGE CONTROL
2
USB EJECT
Use the S A P button to select your desired MTS mode in
analog signal. Each time you press the S A P button, Mono,
Stereo, or SAP appear in turn.
■
CC
USB EJECT
MARK
1
BACK
CC
61
SOUND & LANGUAGE CONTROL
TV SPEAKERS ON/OFF SETUP
TV INPUT
TV INPUT
TV INPUT
Turn the TV speakers off if using external audio equipment.
Feature turns the TVMEDIASpeakers
option On or Off.
HOST
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button
to select the AUDIO menu.
Press the G button and then use D or E button to
select TV Speaker.
Sound Mode
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
RATIO
SIMP
BACK
SOUND & LANGUAGE CONTROL
62
2
PICTURE
SOUND
MARK
USB EJECT
SAP
SAP
PICTURE
MARK
3
BACK
BACK
CC
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
Press the G button and then use D or E button to
select O n or O f f.
Sound Mode
Auto Volume
Balance
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
TV Speaker
G
Off
On
CC
AUDIO LANGUAGE
TV INPUT
TV IN
TV INPUT
TV INPUT
Other languages may be available if a digital signal is proMEDIA HO
ST
vided by the broadcasting
station.
This feature operate only in DTV/CADTV mode.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
Language
1
Press the M E N U button and then use D or E button to
select the OPTION menu.
2
PICTURE
MARK
SAP
SOUND
D
or
E
button to
: English
Input Label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
BACK
CC
SAP
PICTURE
CC
PICTURE
SOUND
MARK
USB EJECT
CC
USB EJECT
MARK
3
SIMP
Press the G button and then use
select Audio.
D
or
E
USB EJECT
button to
Language
G
Input Label
Menu
English
Audio
English
SimpLink
4
5
Use the
French.
F
or G button to select : English, Spanish, or
Key Lock
Caption
Set ID
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Language
Input Label
SOUND & LANGUAGE CONTROL
Press the G button and then use
select Language.
BACK
RATIO
G
Menu
English
Audio
English
SimpLink
Key Lock
Caption
Set ID
63
PIC
M
SOUND & LANGUAGE CONTROL
ON-SCREEN MENUS LANGUAGE SELECTION
TV INPUT
TV INPUT
TV INPUT
The menus can be shown on the screen in the selected lanDIA HOST
guage. First select MEyour
language.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
Language
1
SOUND & LANGUAGE CONTROL
2
Press the M E N U button and then use D or E button
to select the OPTION menu.
Press the G button and then use D or E button to
select Language.
PICTURE
SOUND
MARK
USB EJECT
SAP
: English
Input Label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
BACK
CC
MARK
SAP
CC
USB EJECT
Press the G button and then use D or E button to
select M e n u.
Language
PICTURE
SOUND
MARK
USB EJECT
CC
G
Input Label
Menu
English
Audio
English
SimpLink
Key Lock
4
5
Use the F or G button to select your desired language.
From this point on, the on-screen menus will be shown
in the selected language.
Caption
Set ID
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Language
Input Label
SimpLink
Key Lock
Caption
Set ID
64
SIMP
BACK
PICTURE
3
RATIO
G
Menu
English
Audio
English
BACK
CK
CAPTION MODE
SAP
PICTURE
BACK
BACK
CC
PICTURE
SOUND
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
CC
MARK
MARK
MARK
USB EJECT
USB EJECT
Caption must be provided to help people with hearing loss watch
TV.
1
Use the C C button to select Caption O n or O f f.
■
■
Press E X I T to save and return to TV viewing.
You can also adjust C a p t i o n in the OPTION menu.
Language
: English
Input Label
Language
Input Label
SimpLink
: Off
SimpLink
Key Lock
: Off
Key Lock
Caption
: Off
Caption
Set ID
:1
Set ID
G
Mode
On
Analog
Text1
Digital
Service3
SOUND & LANGUAGE CONTROL
2
When selecting O f f, Sub-menus for Analog, DTV, and
Digital Option become disabled.
Digital Option
65
SOUND & LANGUAGE CONTROL
TV INPUT
TV INPUT
TV INPUT
Analog Broadcasting System Captions
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
Select a caption mode for displaying captioning information
if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog.
Caption/Text, if provided by the broadcaster, would be
available for both digital and analog channels on the
Antenna/Cable.
This TV is programmed to memorize
ri the caption/text mode
which was last set when you turn the power off.
This function is only available when C a p t i o n Mode is set
O n.
Press the M E N U button and then use
to select the O P T I O N menu.
D
or
E
SOUND & LANGUAGE CONTROL
SOUND
MARK
USB EJECT
SAP
button
BACK
CC
SAP
PICTURE
MARK
USB EJECT
2
Press the G button and then use
select C a p t i o n .
D
or
E
button to
3
Press the G button and then use
select A n a l o g .
D
or
E
button to
SIMP
RATIO
: English
CC
SimpLink
: Off
Key Lock
: Off
Caption
Set ID
BACK
: Off SOUND
PICTURE
:1
MARK
CC
USB EJECT
Language
Input Label
SimpLink
4
Use F or G button to select C C 1 ~ 4 , T e x t 1 ~ 4
CAPTION
The term for the words that scroll across the bottom of
the TV screen; usually the audio portion of the program provided for the hearing impaired.
■ TEXT
The term for the words that appear in a large black
frame and almost cover the entire screen; usually messages provided by the broadcaster.
5
Key Lock
Mode
Caption
Analog
Text1
Set ID
Digital
Service3
Digital Option
■
66
T+
Input Label
BACK
PICTURE
BRIGH
LINK
TIMER
Language
1
MENU
T-
BRIGH
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
On
TV INPUT
TV INPU
TV INPUT
TV INPUT
Digital Broadcasting System Captions
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
Choose the language you want the DTV/CADTV Captions
to appear in.
This function in only available when Caption Mode is set
On.
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
Language
1
Press the M E N U button and then use
to select the O P T I O N menu.
BACK
Press the G button and then use
select C a p t i o n.
PICTURE
MARK
SOUND
SAP
D
or
E
or
E
button to
: English
Input Label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
BACK
CC
SAP
PICTURE
CC
PICTURE
SOUND
MARK
USB EJECT
CC
USB EJECT
MARK
3
button
Press the G button and then use
select D i g i t a l.
D
or
E
USB EJECT
button to
Language
Input Label
SimpLink
4
Use F or G button to select S e r v i c e 1 ~ S e r v i c e 6.
Key Lock
Mode
Caption
Analog
Text1
Set ID
Digital
Service3
Digital Option
5
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
On
SOUND & LANGUAGE CONTROL
2
D
SIMP
RATIO
67
PICTU
MAR
SOUND & LANGUAGE CONTROL
TV INPUT
TV INPUT
TV INPUT
Caption Option
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
Customize the DTV/CADTV captions that appear on your
screen.
This function is only available when C a p t i o n Mode is set
O n.
1
2
3
Press the M E N U button and then use
to select the OPTION menu.
D
Press the G button and then use
select Caption.
or
SOUND & LANGUAGE CONTROL
Press the G button and then use
select Digital Option.
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
or
E
E
button to
or
E
button to
RATIO
SIMP
: English
Input Label
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
BACK
CC
Press the G button and then use
select Custom.
SAP
PICTURE
MARK
4
T+
LINK
TIMER
SimpLink
D
BRIGH
button
Language
D
MENU
T-
BRIGH
F
or
G
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
CC
button to
Language
Input Label
SimpLink
5
Use D or E button to customize the Style, Font, etc.,
to your preference.
A preview icon is provided at the bottom of the screen,
use it to see the caption language.
Size: Set the size the words will appear in.
Font: Select a typeface for the words.
■ T e x t C o l o r : Choose a color for the text.
■ T e x t O p a c i t y : Specify the opacity for the text color.
■ Bg (Background)Color: Select a background color.
■ Bg (Background)Opacity: Select the opacity for the
background color.
■ E d g e T y p e : Select an edge type.
■ E d g e C o l o r : Select a color for the edges.
Key Lock
Mode
Caption
Analog
Text1
Set ID
Digital
Service3
Digital Option
On
G
Selection ( G or ) leads you to the
Caption Option screen.
■
■
6
68
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Language
Input Label
SimpLink
Key Lock
Caption
Set ID
Style
Custom
Size
A Standard
Font 0
Mode Font
On
Text Color
White
Analog
Text1
Text Opacity
Solid
Digital
Service3
Bg Color
Black
Digital Bg
Option
G Solid
Opacity
Edge Type
None
Selection ( G or ) leads you to the
Edge Color
Black
Caption Option
screen.
TIME SETTING
CLOCK SETTING
TV INPUT
TV IN
TV INPUT
TV INPUT
Auto Clock Setup
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the current time provided by the broadcasting station.
Set the clock manually if the current time is set incorrectly
by the auto clock function.
T-
BRIGH
MENU
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button to
select the T I M E menu.
RATIO
SIMP
Clock
: Oct 19, 2006, 03:44 AM
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
BACK
2
Press the G button and then use
select Clock.
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
button to
BACK
PIC
CC
PICTURE
SOUND
MARK
USB EJECT
M
D
or
E
USB EJECT
button to
Clock
G
Off Time
Press the G button and then use D or E button to
select your viewing area time zone :
U.S.A: Eastern, Central, Mountain, Pacific, Alaska or
Hawaii.
Canada: Eastern, Central, Mountain, Pacific, N e w
F.land or Atlantic.
Sleep Time
5
---
---/ -: --
--
Auto Sleep
Time Zone
Daylight
Off Time
On Time
Sleep Time
G
Eastern
Auto
Saving
Clock
Press the G button and then use D or E button to
select A u t o, O f f, O n, depending on whether or not
your viewing area observes Daylight Saving time.
Auto
Year
Date
Time
On Time
4
CC
TIME SETTING
Press the G button and then use
select A u t o.
SAP
PICTURE
MARK
3
BACK
CC
Auto
Year
Date
Time
---
---/ -: --
--
Auto Sleep
Time Zone
Eastern
Daylight
Auto
Saving
6
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
69
TIME SETTING
TV INPUT
TV INPUT
TV INPUT
Manual Clock Setup
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
If the current time setting is wrong, reset the clock manually.
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
Press the M E N U button and then use D or E button
to select the T I M E menu.
Press the G button and then use D or E button to
select Clock.
RATIO
SIMP
Clock
: Oct 19, 2006, 03:44 AM
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
BACK
2
PICTURE
SOUND
MARK
USB EJECT
SAP
PICTURE
MARK
TIME SETTING
70
3
BACK
BACK
CC
SAP
CC
PICTURE
SOUND
MARK
USB EJECT
USB EJECT
CC
Press the G button and then use D or E button to
select Manual.
Clock
Off Time
On Time
4
Press the G button and then use F or G button to
select either the year, date, or time option. Once
selected, use the D or E button to set the year, date,
and time options.
5
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Sleep Time
Auto Sleep
G
Manual
Year
Date
Time
---
---/ -: --
--
AUTO ON/OFF TIME SETTING
TV INPUT
TV INPU
TV INPUT
TV INPUT
The timer function operates only if the current time has
MEDIA HO
ST
been set.
The Off-Time function overrides the On-Time function if
they are both set to the same time.
The TV must be in standby mode for the On-Time to work.
If you do not press any button within 2 hours after the TV
turns on with the On Time function, the TV will automatically revert to standby mode.
STB
STB
STB
MEDIA HO
MEDIA HO
ST
ST
MENU
T-
BRIGH
BRIGH
T+
LINK
TIMER
1
2
RATIO
SIMP
Press the M E N U button and then use D or E button to
select the T I M E menu.
Press the G button and then use
select Off Time or On Time.
D
or
E
button to
BACK
BACK
PICTURE
SOUND
SAP
: Oct 19, 2006, 03:44 AM
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
BACK
CC
PICTUR
SAP
PICTURE
MARK
Clock
CC
PICTURE
SOUND
MARK
USB EJECT
CC
MARK
USB EJECT
MARK
USB EJECT
4
Press the G button and then use D or E button to set
the hour.
TIME SETTING
3
Press the G button and then use D or E button to
select O n.
■ To cancel O n / O f f T i m e function, select O f f.
Clock
Off Time
On Time
Sleep Time
G
Off
On
Auto Sleep
5
Press the G button and then use D or E button to set
the minutes.
6
Only On Time
Press the G button and then use
select the channel at turn-on.
D
or
E
Time
Ch.
Vol
6 : 30 AM
TV 2-0
17
button to
Press the G button and then use D or E button to set
the sound level at turn-on.
7
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
71
TIME SETTING
SLEEP TIME SETTING
TV INPUT
TV INPUT
TV INPUT
TV INPUT
The Sleep Time turns the TV off at the preset time.
MEDIA HO
HOST
Note that this setting
is cleared when the TV isMEDIAturned
off.
ST
You can also set up the Sleep Time in the TIME menu.
STB
STB
MEDIA HO
ST
STB
MEDIA HO
TV INPU
STB
MENU
TBRIGH
TIMER
BACK
1
Press the TIMER button repeatedly to select the number of minutes. First
the O f f option appears on the screen, followed by the following Sleep Time
options : 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
2
When the number of minutes you want is displayed on the screen, press the
ENTER button. The timer begins to count down from the number of minutes
selected.
SOUND
MARK
SAP
CC
USB EJECT
PICTURE
SOUND
MARK
USB EJECT
SAP
BRIGH
T+
RATIO
CC
PICTURE
SOUND
MARK
USB EJECT
SAP
CC
TIME SETTING
To check the remaining minutes before the TV turns off, press the TIMER
button once.
4
To cancel the Sleep Time, press the TIMER button repeatedly to select O f f.
PICTURE
SOUND
MARK
USB EJECT
You can also set up the Sleep Time in the TIME menu.
Clock
: Oct 19, 2006, 03:44 AM
Clock
Off Time
: Off
Off Time
On Time
: Off
On Time
Sleep Time
: Off
Sleep Time
Auto Sleep
: Off
Auto Sleep
LINK
SIMP
BACK
BACK
3
■
72
BACK
BACK
MEDIA HO
ST
ST
G
Off
10 min
20 min
30 min
60 min
90 min
120 min
180 min
240 min
SAP
CC
PICTU
MAR
AUTO SHUT-OFF SETTING
TV INPUT
TV INPUT
TV INPUT
TV INPUT
TV will be automatically turned off, in case of no signal inTV
& input source or no remote control input for 10 minutes.
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
BRIGHT
MENU
-
BRIGH
T+
LINK
TIMER
1
2
Press the M E N U button and then use D or E button to
select the T I M E menu.
Press the G button and then use
select Auto Sleep.
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
D
or
E
SIMP
Clock
: Oct 19, 2006, 03:44 AM
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
button to
BACK
BACK
CC
PICTURE
SAP
PICTURE
PICTURE
SOUND
MARK
USB EJECT
CC
D
or
E
USB EJECT
button to
Clock
Off Time
TV will be automatically turned
off, in case of No Signal for 10
minutes.
On Time
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Sleep Time
Auto Sleep
G
Off
On
TIME SETTING
Press the G button and then use
select O n or O f f.
CC
MARK
MARK
3
RATIO
73
PARENTAL CONTROL / RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings
sent by the broadcasting station. The default setting is to allow all programs to be viewed.
Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be
done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television
movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown
at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies:
TV-G
■ TV-PG
■ TV-14
■
PARENTAL CONTROL / RATING
(General audience)
(Parental guidance suggested)
(Parents strongly cautioned)
TV-MA (Mature audience only)
(All children)
■ TV-Y
■ TV-Y7 (Children 7 years older)
■
SET PASSWORD & LOCK SYSTEM
TV INPUT
TV INPUT
TV INPUT
Setting up your Password
STB
MEDIA HO
ST
STB
STB
MEDIA HO
MEDIA HO
ST
ST
Set up blocking schemes to block specific channels, ratings, and
external viewing sources.
A password is required to gain access to this menu.
T-
BRIGH
1
MENU
BRIGH
T+
Press the M E N U button and then use the D or E button to
select the L O C K menu. Then, press the G button.
LINK
TIMER
■
■
Enter the password as requested.
The TV is set up with the initial
password “0-0-0-0”.
RATIO
SIMP
Enter Password
74
BACK
BACK
PICTURE
SOUND
SAP
CC
BACK
Set Password
Change the password by inputting a new password twice.
1
After inputting the password, use the D or E button to
choose Set password.
For USA
For Canada
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Lock System
: Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
Input Block
2
Press the G button and then choose any 4 digits for
your new password and enter the them on the n e w.
As soon as the 4 digits are entered, reenter the same 4
digits on the Confirm.
Then your changed password has been memorized.
Lock System
Set Password
G
Block Channel
New
Confirm
Movie Rating
TV Rating-Children
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
TV Rating-General
Downloadable Rating
Input Block
For USA
For Canada
Enables or disables the blocking scheme you set up previously.
1
After inputting the password, use the D or E button
to choose Lock System.
2
Press the G button and then use the D or E to select
O n or O f f.
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Lock System
■
When you select, the Lock System is enable.
G
Set Password
Lock System
: Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
PARENTAL CONTROL / RATING
Lock System
Off
On
Block Channel
Movie Rating
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
75
PARENTAL CONTROL /RATINGS
CHANNEL BLOCKING
Blocks any channels that you do not want to watch or that
you do not want your children to watch.
For USA
or
button
1
After inputting the password, use the
to choose Block Channel.
2
Press the G button. You will now see a screen filled with
channel numbers and a preview picture.
3
Use D E F G button to select a channel and then use
the ENTER button to block or unblock it.
D
E
For Canada
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Lock System
: Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
Lock System
PARENTAL CONTROL / RATING
76
Set Password
Block Channel
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
G
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Selection ( G or
) leads you to
the block channel screen.
MOVIE & TV RATING
Movie Rating (MPAA) -for USA only
Blocks movies according to the movie ratings limits specified, so children cannot view
certain movies. You can set the ratings limit by blocking out all the movies with the ratings
above a specified level. Keep in mind that the movie ratings limit only applies to movies
shown on TV, not TV programs, such as soap operas.
1
2
Press the G button and then use the D or E to
select G , P G, PG-13, R, NC-17 or X.
■ G (General audiences)
■ PG (Parental guidance suggested)
■ PG-13 (Parents strongly cautioned)
■ R (Restricted)
■ NC-17 (No one 17 and under admitted)
■ X (Adult only)
■ Blocking Off (Permits all programs)
D
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
or E button
After inputting the password, use the
to choose M o v i e R a t i n g.
Downloadable Rating
Input Block
Lock System
Block Channel
If you set PG-13 : G and PG movies will be available,
PG-13, R, NC-17 and X will be blocked.
TV Rating-General
Downloadable Rating
Input Block
For USA
1
After inputting the password, use the D or E button to
choose D o w n l o a d a b l e R a t i n g.
2
Press the G button and then use the D or
to select D i m 0, D i m 1, D i m 2, or D i m 3.
E
Press the G button and then use the
to select D 1 L 1, D 1 L 2, or D 1 L 3.
E
D
or
button
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Lock System
: Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
1
Lock System
Downloadable Rating
Set Password
Movie Rating
TV Rating-Children
NOTE
G
Downloadable Rating
button
Block Channel
G
For Canada
Input Block
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
4
G
PG
PG-13
R
NC-17
X
Blocking Off
TV Rating-General
This function may become available in the future and
will be available only for digital channel signal.
This function operates only when TV has received
Region5 Rating data.
Dim0
PARENTAL CONTROL / RATING
Downloadable Rating
3
G
TV Rating-Children
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
3
Blocking off : permits
all programs
Set Password
Movie Rating
G
: Off
Dim1
Dim2
Dim3
Downloadable Rating G
Input Block
2
G
Based on rating table, your TV's OSD (On
Screen Display) may differ slightly from what
is shown in this manual.
77
PARENTAL CONTROL /RATINGS
TV Rating Children - for USA only
Prevents children from watching certain children's TV
programs, according to the ratings limit set. The children
rating does not apply to other TV programs. Unless you block
certain TV programs intended for mature audiences in the TV
Rating - sub menu, your children can view those programs.
1
After inputting the password, use the D or E button
to choose TV Rating-Children.
2
Press the G button and then use the D or E to select
A g e, or Fantasy Violence.
Press the G button and then use the D or E button
to select block options.
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
: Off
Downloadable Rating
Input Block
Lock System
Set Password
Block Channel
Movie Rating
Age(applies to TV-Y, TV-Y7)
■ Fantasy Violence(applies to TV-Y7)
■
TV Rating-Children
G
TV Rating-General
Age
Fantasy Violence
Downloadable Rating
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Input Block
TV Rating General - for USA only
PARENTAL CONTROL / RATING
Based on the ratings, blocks certain TV programs that you
and your family do not want to view.
1
After inputting the password, use the D or E button
to choose TV Rating-General.
2
Press the G button and then use the D or E button
to select A g e, Dialogue, Language, S e x or Violence.
Press the G button and then use the D or E button
to select block options.
Age(applies to TV-G,TV-PG,TV-14,TV-MA)
■ Dialogue-sexual dialogue(applies to TV-PG,TV-14)
■ Language-adult language(applies to TV-PG,TV-14,TV-MA)
■ Sex-sexual situations(applies to TV-PG,TV-14,TV-MA)
■ Violence(applies to TV-PG,TV-14,TV-MA)
■
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
3
78
G
Downloadable Rating
Input Block
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
: Off
Age
Dialogue
Language
Sex
Violence
TV Rating english - for CANADA only
Selecting canadian english language rating system.
1
2
After inputting the password, use the D or E button
to choose TV Rating-English.
Press the G button and then use the D or E button
to select E, C, C 8 +, G, P G, 1 4 +, 1 8 +, or Blocking Off.
E(Exempt)
■ C(Children)
■ C8+(Children eight years and older)
■ G(General programming, suitable for all audiences)
■ PG(Parental Guidance )
■ 14+(Viewers 14 years and older)
■ 18+(Adult programming)
■ Blocking Off(Permits all programs)
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
: Off
Downloadable Rating
Input Block
■
3
Lock System
Blocking off : permits all
programs
Set Password
Block Channel
TV Rating-English
G
TV Rating-French
Downloadable Rating
Input Block
E
C
C8+
G
PG
14+
18+
Blocking Off
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
TV Rating french - for CANADA only
Selecting canadian french language rating system.
After inputting the password, use the D or E button
to choose TV Rating-French.
2
Press the G button and then use the D or E button
to select E, G, 8 ans+, 13 ans+, 16 ans+, 18 ans+, or
Blocking Off.
E(Exempt)
G(General)
■ 8 ans+(General-Not convenient for little children)
■ 13 ans+(Not convenient for children of 13 years and
younger)
■ 16 ans+(Not convenient for children of 16 years and
younger)
■ 18 ans+(This programs is only for adults)
■ Blocking Off(Permits all programs)
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
: Off
Downloadable Rating
Input Block
■
■
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Blocking off : permits
all programs
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
G
Downloadable Rating
Input Block
PARENTAL CONTROL / RATING
1
E
G
8 ans+
13 ans+
16 ans+
18 ans+
Blocking Off
79
PARENTAL CONTROL /RATINGS
EXTERNAL INPUT BLOCKING
For USA
Enables you to select a source to block from the external
source devices you have hooked up.
1
After inputting the password, use the D or E button to
choose Input Block.
2
Press the G button and then use the
a source.
3
Press the G button and then use the F or G to select
O n or O f f on the each source.
4
D
For Canada
Lock System
: Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Lock System
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Downloadable Rating
Input Block
or E to select
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
G
AV1
AV2
Component1
Component2
RGB-PC
HDMI1
HDMI2
HDMI3
KEY LOCK
PARENTAL CONTROL / RATING
The TV can be set up so that it can only be used with the
remote control.
This feature can be used to prevent unauthorized viewing by
locking out the front panel controls.
This TV is programmed to remember which option it was
last set to even if you turn the TV off.
1
Press the M E N U button and then use D or E button to
select the OPTION menu.
2
Press the G button and then use
select Key Lock.
D
or
E
Language
: English
Input Label
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
button to
Language
Input Label
SimpLink
Key Lock
80
3
Press the G button and then use
select O n or O f f.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
D
or
E
button to
Caption
Set ID
G
Off
On
On
On
Off
On
Off
On
Off
Off
APPENDIX
TROUBLESHOOTING
The operation does not work normally.
Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■ Ensure that the correct remote operating mode is set: TV, VCR etc.
■ Install new batteries.
■
The remote control
doesn’t work
Is the sleep timer set?
■ Check the power control settings. Power interrupted.
■ No broadcast on station tuned with Auto off activated.
■
Power is suddenly
turned off
The video function does not work.
Check whether the product is turned on.
■ Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted into wall power outlet?
■ Check your antenna direction and/or location.
■ Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
■
No picture & No sound
Picture appears slowly
after switching on
■
This is normal, the image is muted during the product startups process. Please
contact your service center, if the picture has not appeared after five minutes.
■
No or poor color
or poor picture
Horizontal/vertical bars
or picture shaking
■
APPENDIX
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
■ Check for sources of possible interference.
■
Poor reception on
some channels
Lines or streaks
in pictures
■
■
Check antenna (Change the direction of the antenna).
81
APPENDIX
The audio function does not work.
Press the VOL or VOLUME button.
■ Sound muted? Press MUTE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■
Picture OK & No sound
No output from one
of the speakers
Unusual sound from
inside
the product
■
Adjust Balance in menu option.
■
A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
(Invalid format)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
APPENDIX
82
Screen color is unstable
or single color
■
Adjust resolution, horizontal frequency, or vertical frequency.
Check the input source.
■
Work the Auto configure or adjust clock, phase, or H/V position. (Option)
■
Check the signal cable.
■ Reinstall the PC video card.
■
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
■
■
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Extended Absence
CAUTION
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
APPENDIX
83
APPENDIX
PRODUCT SPECIFICATIONS
■
The specifications shown above may be changed without prior notice for quality improvement.
MODELS
Including stand
47LBX
(47LB9DF-UA)
40.6 x 30.7 x 13.8 inches
45.3 x 33.8 x 15.0 inches
52LBX
(52LB9DF-UA)
50.7 x 37.4 x 16.6 inches
1030.0 x 781.0 x 350.0 mm 1150.0 x 859.0 x 381.0 mm 1289.0 x 950.0 x 421.0 mm
Dimensions
(Width x Height x Depth)
42LBX
(42LB9DF-UA)
Excluding stand
40.6 x 27.3 x 3.5 inches
45.3 x 30.2 x 4.1 inches
50.7 x 33.8 x 4.4 inches
1030.0 x 693.0 x 88.5 mm 1150.0 x 768.0 x 103.0 mm 1289.0 x 858.0 x 112.0 mm
Weight
including stand
56.9 pounds / 25.8kg
83.8 pounds / 38.0 kg 110.2 pounds / 50.0 kg
excluding stand
48.3 pounds / 21.9kg
70.5 pounds / 32.0 kg
Power requirement
AC100-240V ~ 50/60Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
External Antenna Impedance
Operating Temperature
32 ~ 104°F (0 ~ 40°C)
Operating Humidity
Less than 80%
Storage Temperature
-4 ~ 140°F (-20 ~ 60°C)
Environment condition
Storage Humidity
APPENDIX
84
90.4 pounds / 41.0 kg
Less than 85%
PROGRAMMING THE REMOTE CONTROL
The provided universal remote control can be programmed to operate most remote-controllable devices.
Note that the remote may not control all models of other brands.
Programming a code into a remote mode
1
To find out whether your remote control can operate each device without programming, turn on the device
(such as a VCR) and press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off and it responds properly the remote control
need not be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below.
2
Press the M E N U and M U T E button continuously at the same time for two seconds; the currently selected
device button is illuminated.
If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case,
you have to repeat from step 2.
3
Enter the appropriate code from the code table on the following pages. When pressing the button, the light
blinks at a time. If the device turned off, the programming is successful.
4
Press the M E N U button to store the code. After blinking twice, this code is stored.
5
Test the remote control functions to see if the device responds properly. If not, steps 2-5.
APPENDIX
85
APPENDIX
Remote control code
VCRs
Brand
AIWA
AKAI
APPENDIX
86
Codes
034
016
125
AMPRO
072
ANAM
031
AUDIO DYNAMICS 012
BROKSONIC
035
CANON
028
CAPEHART
108
CRAIG
003
CURTIS MATHES 031
DAEWOO
005
065
112
DAYTRON
108
DBX
012
DYNATECH
034
ELECTROHOME 059
EMERSON
006
029
036
129
FISHER
003
FUNAI
034
GE
031
107
GO VIDEO
132
HARMAN KARDON
HITACHI
004
043
INSTANTREPLAY 031
JCL
031
JCPENNY
012
040
JENSEN
043
JVC
012
048
130
KENWOOD
014
047
LG (GOLDSTAR) 001
101
LLOYD
034
LXI
003
017
MAGIN
040
Brand
Codes
Brand
MAGNAVOX
031 033 034 041
067 068
012 031 033 067
SAMSUNG
MARANTZ
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
043 046 124
146
033
023
037
031
103
039 043
129
033
MARTA
MATSUI
MEI
MEMOREX
040
033
007
108
116
135
041
010 064
110 111
117 119
MGA
MINOLTA
MITSUBISHI
023 039 043
053
017
031
037
131
008
025
034
046
138
009
033
109
136
012
018
063
033
033
013
066
063 072
144 147
031
050
150
034
048
012
106
027
035
101
153
010
045
026 034
137 150
015 033
101
033 043
055 060
152
039 043
MTC
MULTITECH
NEC
NORDMENDE
OPTONICA
PANASONIC
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
REALISTIC
013 020
114 123
009 013 014
034 101 106
RICO
RUNCO
SALORA
013
063
031
031
067
101
013
108
072
011
033
013
040
107
145
003
031
053
058
148
014
030
033
010
034
102
046
020
020
051
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
Codes
032
105
113
125
SANSUI
022
SANYO
003
102
SCOTT
017
131
SEARS
003
013
031
101
SHARP
031
SHINTOM
024
SONY
003
056
077
SOUNDESIGN
034
STS
013
SYLVANIA
031
067
SYMPHONIC
034
TANDY
010
TATUNG
039
TEAC
034
TECHNICS
031
TEKNIKA
019
101
THOMAS
034
TMK
006
TOSHIBA
008
059
TOTEVISION
040
UNITECH
040
VECTOR RESEARCH 012
VICTOR
048
VIDEO CONCEPTS 012
VIDEOSONIC
040
WARDS
003
031
053
YAMAHA
012
ZENITH
034
058
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
HDSTB
Brand
Codes
ALPHASTAR DSR
AMPLICA
BIRDVIEW
CHANNEL MASTER
123
050
051
013
036
CHAPARRAL
008
CITOH
054
CURTIS MATHES 050
DRAKE
005
011
141
DX ANTENNA
024
ECHOSTAR
038
093
097
122
ELECTRO HOME 089
EUROPLUS
114
FUJITSU
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
Brand
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
021 022 027
134
004 016 029
059 101
140
Codes
HOUSTON TRACKER 033
057
HUGHES
068
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
MEMOREX
057
NEXTWAVE
028
NORSAT
069
PACE SKY SATELLITE 143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
037 039 051
104
147
144
059 063 064
124 125
070
142
102
110 111
Brand
Codes
PROSAT
RCA
REALISTIC
SAMSUNG
SATELLITE SERVICE CO
072
066
043
123
028
085
SCIENTIFIC ATLANTA 032
SONY
103
STARCAST
041
SUPER GUIDE
020
TEECOM
023
088
137
TOSHIBA
002
UNIDEN
016
044
078
101
VIEWSTAR
115
WINEGARD
128
ZENITH
081
091
106
074
035 047 057
138
124 125
026 075 087
090 107 130
127
025 042 043
045 048 049
079 080 086
135 136
146
082 083 084
120
Brand
Codes
APEX DIGITAL
022
DENON
020
GE
005
HARMAN KARDON
JVC
012
LG
001
MAGNAVOX
013
MARANTZ
024
014
006
027
010 016 025
Brand
Codes
Brand
Codes
MITSUBISHI
NAD
ONKYO
PANASONIC
PHILIPS
PIONEER
PROCEED
PROSCAN
002
023
008
003
013
004
021
005
RCA
SAMSUNG
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
005
011
007
005
019
009
010
017
009
026
APPENDIX
DVD
006
015
006
008
018
016 025
006
87
APPENDIX
Audio
Brand
AIWA
APPENDIX
88
Codes
014
125
230
AKAI
163
ANAM
003
059
217
BURMECTER
252
CARVER
086
CLARION
199
DAEWOO
027
102
DENON
015
FANTASIA
071
FINEARTS
022
FISHER
089
LG(GOLDSTAR) 001
087
190
211
HAITAI
034
HARMAN/KARDON
JVC
004
KEC
185
KOHEL
030
NAD
045
KENWOOD
038
170
215
INKEL
037
078
122
152
Brand
028 070 096
129 139 229
014 017 023
106 189 216
235 236
053 060 084
148 198 221
075 130 143
099
021
107
191
212
035
068
013
186
046
050
171
222
058
079
149
153
024
108
192
239
188
029
110
210
222
141
187
LXI
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MEMOREX
NAD
ONKYO
OPTIMUS
PANASONIC
067 089
197 206
062
095
150
154
LOTTE
069
121
151
155
PENNEY
PHILIPS
PIONEER
QUASAR
RCA
Codes
Brand
Codes
157
189
225
247
014
100
175
179
201
214
238
103
111
002
034
097
049
104
107
046
013
048
133
158
007
142
104
026
039
065
115
113
080
RCX
REALISTIC
SAMSUNG
092
103
124
193
204
011
019
106
031
072
156
206
005
044
118
012
076
162
166
205
158 159 160
207 222 224
226 227 243
016
172
176
180
202
219
240
036
173
177
181
208
223
098
174
178
183
213
232
018 020 025
041 081 090
112
040 041 047
056 057 132
140
SANSUI
SANYO
SCOTT
SHARP
SHERWOOD
SONY
TAEKWANG
TEAC
TECHNICS
033 064 113
220 241 251
112
042
091
123
143
043 063
093 094
127 250
TOSHIBA
THE
VICTOR
WARDS
YAMAHA
010
185
101
147
137
061
088
089
054
199
106
145
194
244
135
083
186
032
082
184
209
006
045
126
020
077
163
167
231
146
195
245
138
234
182
203
246
144
051 052
117 119
199 200
158
109
248
073
105
164
168
233
114
249
074
161
165
169
242
085 106 136
187 237
113 128 134
218
131
055 066 092
IR CODES
1. How to Connect
■
Connect your wired remote control to the Remote Control port on the TV.
2. Remote Control IR Codes
■
Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
Carrier frequency
Tc
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
■
Configuration of frame
1st frame
Lead code
Low custom code
High custom code
Data code
C0 C1 C2 C3 C4 C5 C6 C7
Data code
D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
■
Tf
Lead code
9 ms
■
APPENDIX
4.5 ms
Repeat code
0.55 ms
9 ms
■
2.25 ms
Bit description
Bit ”0”
Bit ”1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
■
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
89
APPENDIX
(Hexa)
Code
Function
Note
0F
TV INPUT
Remote Control Button
0B
INPUT
Remote Control Button
08
POWER
Remote Control Button (Power On/Off) D4
79
RATIO
Remote Control Button
0E
TIMER
Remote Control Button
10-19
Number Key 0-9
Remote Control Button
4C
- (Dash)
Remote Control Button
Function
BF
COMPONENT1
Note
Discrete IR Code
(Component1 Input Selection)
COMPONENT2
Discrete IR Code
(Component2 Input Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI1
CC
HDMI2
Discrete IR Code
(HDMI1 Input Selection)
APPENDIX
1A
BACK
Remote Control Button
09
MUTE
Remote Control Button
02
VOL D
Remote Control Button
03
VOL E
Remote Control Button
00
CH D
Remote Control Button
01
CH E
Remote Control Button
1E
FAV
Remote Control Button
39
CC
Remote Control Button
40
D
Remote Control Button
41
E
Remote Control Button
07
F
Remote Control Button
06
G
Remote Control Button
44
ENTER
Remote Control Button
34
BRIGHT-
Remote Control Button
B0
PLAY
Remote Control Button
43
MENU
Remote Control Button
BA
PAUSE
Remote Control Button
33
BRIGHT+
Remote Control Button
B1
STOP
Remote Control Button
52
SOUND
Remote Control Button
BD
REC
Remote Control Button
4D
PICTURE
Remote Control Button
8F
REW
Remote Control Button
5B
EXIT
Remote Control Button
8E
FF
Remote Control Button
7E
SIMPLINK
Remote Control Button
B2
GO TO PREV
Remote Control Button
0A
SAP
Remote Control Button
B3
GO TO NEXT
Remote Control Button
D6
TV
Discrete IR Code
7C
MEDIA HOST
Remote Control Button
(TV Input Selection)
7D
MARK
Remote Control Button
Discrete IR Code
CA
USB EJECT
Remote Control Button
5A
AV1
D0
AV2
(AV1 Input Selection)
Discrete IR Code
(AV2 Input Selection)
90
Code
(Hexa)
Discrete IR Code
(HDMI2 Input Selection)
76
Ratio 4:3
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
Discrete IR Code
(Only 16:9 Mode)
AF
Ratio Zoom
Discrete IR Code
C4
POWER ON
Discrete IR Code
(Only Zoom1 Mode)
(Only Power On)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
EXTERNAL CONTROL THROUGH RS-232C
Connect the RS-232C (serial port) input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied with the product.
RS-232C Setup
REMOTE
CONTROL IN
DIGITAL AUDIO OUT
OPTICAL COAXIAL
RS-232C IN
(CONTROL & SERVICE)
S-VIDEO VIDEO
UDIO
(MONO)
AUDIO
AV IN 1
AUDIO OUT
PC
Type of Connector; D-Sub 9-Pin Male
Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
APPENDIX
No.
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
91
APPENDIX
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
TV INPUT
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
STB
MEDIA HO
ST
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations(Not standard)
RXD
TXD
GND
DTR
DSR
RTS
CTS
TV INPUT
D-Sub 9
STB
MEDIA HO
ST
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
7
8
TXD
RXD
GND
DTR
DSR
RTS
CTS
TV INPUT
D-Sub 9
D-Sub 9
STB
MEDIA HO
ST
MENU
T-
BRIGH
BRIGH
T+
Set ID
Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping 1’. p .95
LINK
TIMER
Language
1
2
Press the M E N U button and then use D or E button
to select the OPTION menu.
: English
SimpLink
: Off
Key Lock
: Off
Caption
: Off
Set ID
:1
BACK
PICTURE
SOUND
MARK
USB EJECT
SAP
BACK
BACK
CC
MARK
SAP
CC
USB EJECT
APPENDIX
Press the G button and then use D or E button to
adjust SET ID to choose the desired TV ID number.
The adjustment range of SET ID is 1~99.
PICTURE
SOUND
MARK
USB EJECT
CC
Language
Input label
SimpLink
Key Lock
Caption
Set ID
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Communication Parameters
Baud rate : 9600 bps (UART)
■ Data length : 8 bits
■ Parity : None
■
Stop bit : 1 bit
Communication code : ASCII code
■ Use a crossed (reverse) cable.
■
■
NOTE
This product has command echo back in the RS-232C Command.
92
SIMP
Input label
Press the G button and then use D or E button to
select SET ID.
PICTURE
3
RATIO
G
1
Command Reference List
COMMAND1 COMMAND2
01. Power
k
a
DATA
(Hexadecimal)
DATA
(Hexadecimal)
0~1
12. Sharpness
k
k
0 ~ 64
13. OSD Select
k
l
0~1
14. Remote Control/
Key Lock
k
m
0~1
15. Treble
k
r
0 ~ 64
16. Bass
k
s
0 ~ 64
17. Balance
k
t
0 ~ 64
18. Color Temperature
k
u
0~3
19. Red adjustment
k
v
0 ~ C8
20. Green adjustment
k
w
0 ~ C8
21. Blue adjustment
k
$
0 ~ C8
02. Input Select
k
b
0~9
03. Input Select
x
b
*
04. Aspect Ratio
k
c
*
05. Screen Mute
k
d
0~1
06. Volume Mute
k
e
0~1
07. Volume Control
k
f
0 ~ 64
08. Contrast
k
g
0 ~ 64
09. Brightness
k
h
0 ~ 64
10. Color
k
i
0 ~ 64
11. Tint
k
j
0 ~ 64
COMMAND1 COMMAND2
COMMAND1 COMMAND2
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
physical
major
major low
program high program low
22. Tune Command
m
a
23. Channel Add/Del
m
b
0~1
24. Key
m
c
key code
25. Back Light
m
g
0~64
minor high
minor low
attribute
APPENDIX
93
APPENDIX
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected the TV
is controlled. Set ID is indicated as decimal (1~
99) on menu and as Hexa decimal (0x0~ 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
*In this model, TV will not send the status during the standby
mode.
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this
format when receiving normal data. At this time, if the data
is data read mode, it indicates present status data. If the
data is data write mode, it returns the data of the PC computer.
*in this model, TV will not send the status during the standby
mode.
*data format
[command 2] : use as command.
[Set ID] : use the small character, if set ID is 10, it will send
the ‘0’,’a’
[Data] : use the small character, if data is 0xab, it will send
the ‘a’, ‘b’
[OK] : use the large character
*in this model, TV will send the echo, CR, LF with ack message.
When it send the power on ack message, it will be like below.
Ex) ka 01 01(CR)(LF)a 01 OK01x(CR)(LF)
Error Acknowledgement
APPENDIX
[Command2][ ][Set ID][ ][NG][Data][x]
The TV transmits ACK (acknowledgement) based on this
format when receiving abnormal data from non-viable functions or communication errors.
will send the ‘a’, ‘b’
[NG] : use the large character
*in this model, TV will send the echo, CR, LF with
Data1: Illegal Code
ack message.
Data2: Not supported function
When it send the power on ack message, it will be
Data3: Wait more time
like below.
*in this model, TV will not send the status during
the standby mode.
*data format
[command 2] : use as command.
[Set ID] : use the small character, if set ID is 10, it
will send the ‘0’,’a’
94
[Data] : use the small character, if data is 0xab, it
Ex) ka 01 01(CR)(LF)a 01 NG01x(CR)(LF)
0 1 . Power (Command2:a)
0 5 . Screen Mute (Command2:d)
To control Power On/Off of the TV.
To select screen mute on/off.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
Data 0 : Screen mute off (Picture on)
Data 1 : Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
Data 1 : Screen mute on (Picture off)
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
06. Volume Mute (Command2:e)
To control volume mute on/off.
* Note: In this model, TV will send the Acknowledge
after power on processing completion.
You can also adjust mute using the MUTE button on
remote control.
There might be a time delay between command and
acknowledge.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
02. Input Select (Command2:b)
To select input source for the TV.
Transmission [k][b][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off)
Data 1 : Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
07. Volume Control (Command2:f)
Data 0: DTV
Data 1: Analog
Data 2: AV1
Data 3: AV2
Data 4: Component 1
Data 5: Component 2
You can also adjust volume with the volume buttons on
remote control.
Data 7: RGB-PC
Data 8: HDMI1
Transmission [k][f][ ][Set ID][ ][Data][Cr]
To adjust volume.
Data 9: HDMI2
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code)
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Refer to ‘Real data mapping 1’ as shown below.
* You can select HDMI3 using (cc o m m a n d x b).
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
* If you select input source, we command (cc o m m a n d x b).
08. Contrast (Command2:g)
03. Input select(Command: x b)
To select input source for TV.
To adjust screen contrast.
Transmission [x][b][][Set ID][][Data][Cr]
You can also adjust contrast in the Picture menu.
Data 01 : DTV (Cable)
Data 10 : Analog (Antenna)
Data 11 : Analog (Cable)
Data 20 : AV1
Data 21 : AV2
Data 40 : Component 1
Data 41 : Component 2
Data 60 : RGB-PC
Data 90 : HDMI1
Data 91 : HDMI2
Data 92 : HDMI3
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
0 9 . Brightness (Command2:h)
APPENDIX
Data 00 : DTV (Antenna)
To adjust screen brightness.
You can also adjust brightness in the Picture menu.
04. Aspect Ratio (Command2:c) (Main picture format)
Transmission [k][h][ ][Set ID][ ][Data][Cr]
To adjust the screen format.
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code)
You can also adjust the screen format using the RATIO
button on remote control or in the Picture menu.
*Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 1: 4:3
2: 16:9
4: Zoom 1
5: Zoom 2
6: Set by program
Reserved
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
95
APPENDIX
14. Remote Control Lock Mode (Command2:m)
*Real data mapping 1
0 : Step 0
To lock the remote control and the front panel controls
on the set.
A : Step 10 (SET ID 10)
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
Data 1: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
F : Step 15 (SET ID 15)
If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
1 5 Treble (Command2:r)
To adjust treble.
10. Color (Command2:i)
You can also adjust treble in the Audio menu.
To adjust the screen color.
You can also adjust color in the Picture menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
1 6 . Bass (Command2:s)
To adjust bass.
11. Tint (Command2:j)
You can also adjust bass in the Audio menu.
To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
17. Balance (Command2:t)
To adjust balance.
12. Sharpness (Command2:k)
APPENDIX
To adjust the screen sharpness.
You can also adjust sharpness in the Picture menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
You can also adjust balance in the Audio menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 96.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
18. Color Temperature (Command2:u)
To adjust color temperature.
13. OSD Select (Command2:l)
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off
Data 1: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
96
You can also adjust color temperature in the Picture
menu.
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data 0: Medium 1: Cool 2: Warm 3: User
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
19. Red adjustment(Command:v)
To adjust red in color temperature
22. Tune Command (Command: m a)
Transmission [k][v][ ][Set ID][][Data][Cr]
To tune channel to following physical/major/minor num
ber.
Data Min:0 ~ Max:C8
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1]
*Refer to "Real data mapping 2". See page 97.
[ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
20. Green adjustment(Command:w)
Data 0: Physical Channel Number(Transmit by
Hexadecimal code)
To adjust green in color temperature.
NTSC air:02~45
Transmission [k][w][ ][Set ID][][Data][Cr]
NTSC cable: 01, 0E~7D
Data Min:0 ~ Max:C8
ATSC air:01~45
*Refer to "Real data mapping 2". See page 97.
Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x]
ATSC cable:01~87
Data1,Data2: Major Channel Number (two part) /
Channel Number (One part)
21. Blue adjustment(Command:$)
Data1: High byte
To adjust blue in color temperature.
Data2: Low byte
Transmission [k][$][ ][Set ID][][Data][Cr]
Two part channel number:
Data Min:0 ~ Max:C8
Major number-Minor number
*Refer to "Real data mapping 2". See page 97.
One part channel number:
Acknowledgement [$][ ][Set ID][][OK/NG][Data][x]]
If the channel band is ATSC digital cable, it can
be used. In case of using one part channel number, minor channel does not need.
*Real data mapping 2
0 : -20
5 : -19
Data3, Data 4: Minor Channel Number
Data3: High byte , Data4: Low byte
A : -18
5F: -1
64: 0
C3 : +19
C8 : +20
APPENDIX
69: +1
97
APPENDIX
Data5:
7
Main/Sub
Picture
6
Two/One
Part Channel
5
Using Physical
Channel
4
3
2
1
0
Step
NTSC Air
NTSC Cable
ATSC Air
ATSC Cable_std
ATSC Cable_hrc
ATSC Cable_irc
ATSC cable_auto
Reserved
...
Reserved
Reserved
0 Main
0 Two
0 Use
x
0
0
0
0
1 Sub
1 One
1 No Use
x
0
0
0
1
x
0
0
1
0
x
0
0
1
1
x
0
1
0
0
x
0
1
0
1
x
0
1
1
0
x
0
1
1
1
All data are transmitted by Hexadecimal code
* Two/One part Channel: 6th bit
This bit is used in a cable-ready system.
* Using physical channel: 5th bit
If the channel band is NTSC air or NTSC cable, channel
tuning can be done by only physical channel. In this
case, using physical channel bit must be low(0).
But if the channel band is ATSC air or ATSC cable, there
are two cases that physical channel enable or disable.
If the physical channel sending is meaningful, you should
set this bit low(0). If the physical channel sending is
meaningless, you should set this bit high(1).
x
x
x
x
x
x
1
1
1
1
23. Channel Add/Del (Command: m b)
To add and delete the channels
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 0: Channel Delete
Data 1: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
24. Key (Command: m c)
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]s
Data Key code: Refer to page 90.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
Example)
APPENDIX
1. Analog channel: NTSC cable, channel number(35),
main picture Command: ma 00 23 xx xx xx xx 01
attribute(0x01): main picture, two part(it’s not
mandatory), using physical channel, NTSC cable ‘xx’
data: don’t care major and minor channel number in
case analog channel tuning.
2. Digital channel: ATSC air, channel number(don’t know
physical channel, major(30), minor(3)), sub picture
Command: ma 00 xx 00 1E 00 03 A2
attribute(0xA2): sub picture, two part, not using
physical channel, ATSC air ‘xx’ data: don’t care analog
channel number in case digital channel tuning.
3. Digital channel: ATSC air, channel number(physical(20),major(20), minor(3)), sub picture Command:
ma 00 14 00 14 00 03 82
attribute(0x82): sub picture, two part, using physical
channel, ATSC air.
Acknowledgement[a][ ][Set ID][ ][OK][Data0][Data1]
[Data2][Data3][Data4][x][a][ ][Set ID]
[ ][NG][Data0][x]
98
25. Back light(Command: m g)
To adjust screen back light.
Transmission [m][g][][Set ID][][Data][Cr]
Data Min:0 ~ Max:64(*transmit by Hexadecimal code)
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
Download PDF

advertising