Dodge 2004 Ram 3500 Automobile User Manual

INSTRUCTIONS
• This unit can only play the iPod audio.
You can use the iPod video function and hear the audio but cannot play the video.
• Do not carry the System with iPod connected. You might drop it down or it might cause
damages to the connector part.
• Do not touch or hit the iPod terminal pins or the connector pins directly. It might cause
damages to the connector part.
• If the iPod does not play correctly, please update your iPod software to the latest version. - For details about updating your iPod, check on the Apple web site <http://www.
apple.com>.
• JVC is not responsible for any loss of or damage to iPod that might result from the use
of this product.
• Sound distortion may occur when playing back audio sources with high recording
levels. When distortion occurs, it is recommended to turn off the equalizer of the iPod.
For information on operating the iPod, see the iPod instruction manual.
• If you do not turn on the power of this unit and only connect the iPod to this unit, power
may be supplied to the iPod.
• “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been
designed to connect specifically to iPod or iPhone, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for
the operation of this device or its compliance with safety and regulatory standards.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
PORTABLE AUDIO SYSTEM
RA-P1B/RA-P1W
iPod Compatibility Chart
iPod touch (2nd generation and Fall '09)
iPod touch
iPhone 3GS
iPhone 3G
iPhone
iPod classic
iPod video (5th Generation)
iPod photo (4th Generation)
iPod nano (5th Generation)
iPod nano (4th Generation)
iPod nano (3rd Generation)
iPod nano (2nd Generation)
iPod nano
iPod (4th Generation)
iPod mini (2nd Generation)
iPod mini
n NOTES on iPod
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
©2010 Victor Company of Japan, Limited
Rating label is placed on the exterior of the bottom.
Model No.
[European Union only]
[Union européenne seulement]
Precautions
• Install in a place which is level, dry and neither too hot nor too cold–between 5°C and
35°C (41°F and 95°F).
• Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System.
DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.
• Leave sufficient distance between the System and the TV.
• Keep the speakers away from the TV to avoid interference with TV.
For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus
as follows:
1.Front: No obstructions and open spacing.
2.Sides/ Top/ Back: No obstructions should be placed in the areas indicated by the
dimensions in the illustration.
3.Bottom: Place on the level surface. Maintain an adequate air path for ventilation
by placing on a stand with a height of 10 cm (3-15/16") or more.
Front
Face
Warnings, Cautions and Others / Mises en garde, précautions et indications diverses
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT : POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS
ÉLECTRIQUES, NE PAS EXPOSER CE APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
CAUTION:
• Do not block the ventilation openings or holes. (If the ventilation openings or holes
are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local
rules or laws governing the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
ATTENTION:
• Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous
de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne pas être
évacuée correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement et suivre strictement les règles et les lois locales sur la mise au rebut des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un éqgouttement ou à des éclaboussures et ne placez pas des objets remplis de liquide, tels qu’un vase, sur l’appareil.
For U.S.A
Caution: Changes or modifications not expressly approved by party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
CAUTION
To reduce the risk of electrical, shocks, fire etc.:
1 Do not remove screws, covers or cabinet.
2 Do not expose this appliance to rain or moisture.
To avoid the risk of fire and to prevent damage,
– Do not use any AC adaptors other than the one supplied.
– Do not use the supplied AC adaptor for other equipment.
Pour les Etats-Unis
Attention : Les changements ou les modifications qui ne sont pas explicitement
approuvés par la partie responsable de l’observance pourraient mettre fin au droit de l’
utilisateur d’utiliser le matériel.
Remarque: Cet appareil a été testé et il s’est avéré conforme aux limites applicables
à un appareil numérique de classe B, en vertu de la Partie 15 des Règles de la FCC.
Ces limites sont conçues de manière à assurer une protection raisonnable contre les
interférences nuisibles dans une installation résidentielle. Cet appareil produit, utilise
et peut émettre une énergie de haute fréquence et, s’il n’est pas installé et utilisé en
conformité avec les instructions, il peut causer des interférences nuisibles aux communications radio. Il n’y a, toutefois, aucune garantie que des interférences ne se
produiront pas dans une installation particulière. Si cet appareil cause effectivement
des interférences nuisibles à la réception de la radio ou de la télévision, ce qu’on
peut établir en mettant l’appareil en marche et à l’arrêt, nous encourageons l’utilisateur à tenter de corriger l’interférence par une ou plusieurs des mesures suivantes :
–Réorienter ou déplacer l’antenne de réception ;
–Accroître la séparation entre l’appareil et le récepteur ;
–Brancher l’appareil dans une prise ou un circuit autre que celui auquel le récepteur
est branché ;
–Consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.
ATTENTION
Afin d’eviter tout risque d’electrocution, d’incendie, etc.:
1 Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2 Ne pas exposer l’appareil a la pluie ni a l’humidité.
Pour éviter tout risque d'incendie et pour prévenir tout dommage,
– N’utilisez aucun autre adaptateur CA que l’adaptateur secteur fourni.
– N'utilisez pas l'adaptateur CA d'un autre appareil.
Précautions
• Installez la chaîne dans un endroit plat, sec, et ni trop chaud, ni trop froid-entre 5°C et
35°C.
• Installez la chaîne dans un endroit avec une bonne ventilation pour éviter tout échauffement intérieur de l’appareil.
N’INSTALLEZ PAS la chaîne dans en endroit proche d’une source de chaleur ou sujet à la
lumière directe du soleil, à un poussière excessive ou à des vibrations.
• Laissez suffisamment d’espace entre la chaîne et le téléviseur.
• Éloignez les enceintes du téléviseur pour éviter toute interférence avec ce dernier.
Serial No.
LVT2122-002B [J,C]
0510KMMCREBET
Attention
La touche
, quelle que soit sa position, ne coupe pas la ligne principale. Débrancher la fiche principale pour couper complètement l’alimentation du secteur.
La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion
de l’appareil, et l’appareil déconnecté doit être prêt à être utilisé.
L’étiquette des caractéristiques nominales se trouve sur l’extérieur du coffret.
CAUTION
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Thank you for purchasing a JVC product.
EN
CAUTION
The
button in any position does not disconnect the mains line. Disconnect the
mains plug to shut the power off completely.
The MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
Pour le Canada
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”,
NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
Attention
Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du
soleil, feu, etc.).
Attention: Aération correcte
Pour prévenir tout risque de décharge électrique ou d’incendie et éviter toute détérioration, installez
l’appareil de la manière suivante:
1.Avant: Bien dégagé de tout objet.
2.Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués
sur le schéma ci-dessous.
3.Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que
sa ventilation correcte puisse se faire en le plaçant sur un support d’au moins dix
centimètres de hauteur.
Side
Côté
15cm
(5-15/16")
15cm
15cm
15cm
(5-15/16")
(5-15/16")
(5-15/16")
15cm
(5-15/16")
10cm
(3-15/16")
Specifications
Troubleshooting
Model
Type
Amplifier
RA-P1B/RA-P1W
Portable audio system
Power Output
Input Sensitivity/ Impedance AUDIO IN
Tuner
Speaker
Input Terminal
iPod connector
Power Source
Power Consumption
AC adaptor
2W + 2 W
1 kHz 10 % THD, 4 Ω
If you are having a problem with your System, check this list for a possible solution before calling for service.
In these cases
Power does not come on.
Press the RESET button (see "Resetting the unit" below).
250 mV / 47 k Ω
Tuning Range
87.5 MHz - 108.0 MHz
No longer works.
Preset Stations
10
Cannot set the iPod.
1way full range, diameter 40 mm x 2
External DC IN (for AC adaptor)
Cannot operate iPod.
AUDIO IN (mini jack)
Output Power : DC5 V
500 mA
DC 6 V
2 A (EXTERNAL DC IN)
DC 6 V
(SIZE R6, AA BATTERY OR EQUIVALENT x 4)
0.5 W (When not under load) / 1.00 W or less (in Standby mode) / 3.5 W (with
iPod devices connected)
Input : AC 120 V , 60 Hz 0.5A
Output : DC 6 V
2A
Dimensions (W x H x D)
(W) 240 mm × (H) 58 mm × (D) 81 mm
(9-1/2" x 2-5/16" x 3-1/4")
Weight (Without batteries)
0.35 kg (0.78 lbs)
Accessory
AC adaptor
Check the following points
• AC adaptor is not inserted securely. Plug in securely.
• The batteries are exhausted.
• Is the timer set? Turn off the alarm.
iPod cannot be charged.
Hard to listen to broadcasts because of noise.
When the volume level is manually
set higher than “16”, the unit automatically lowers the level to “16”.
• Is the Dock adaptor properly mounted on the unit? Make sure to
mount the Dock adaptor properly.
• Is the iPod firmly connected to the connector plug of the unit?
• Is the iPod properly functioning? Test the iPod functions in stand alone
condition.
• Is the iPod firmly connected to the connector plug of the unit?
• Is the AC adaptor connected? The iPod cannot be charged while the
Unit is operated on batteries.
The FM antenna is not properly extended and positioned.
The batteries run low. Replace the batteries with new ones, or use the
AC adaptor.
Resetting the unit
If "Troubleshooting" does not eliminate malfunctioning (failure to operate or display properly, etc.),
press the RESET button on the bottom of the unit with something having a sharp point, while the unit is turned on.
After pressing RESET button, unplug the AC adaptor and wait a while before plugging it again.
• While resetting the unit, the clock is also reset. Adjust the clock after resetting the unit.
• Specifications and appearance are subject to change without prior notice.
RESET
–1–
Preparation of the Unit
Listening to FM Broadcasts
nSetting the batteries / AC adaptor
nSetting the time
This Unit runs on AA batteries or from the AC adaptor.
To load batteries, open the covers of the battery compartments and
insert AA batteries (not supplied) in the right and left compartments
(four batteries total).
Be sure to match the poles (+/-) correctly.
Set the time with the power off.
CAUTION
Read “Safety Precautions” on page 1 thoroughly in order to handle the dry batteries correctly.
nListening to the radio
2 While the time display is flashing, press the
SOURCE button.
Extend the wire antenna to use it.
nRegistering broadcast station in preset channels
(Presetting)
1 Turn on the power.
You can preset up to 10 preferred stations (P01 to P10).
1 Select “FM” with the SOURCE button.
3 Select the time display setting and the current
time.
2 Select “FM” with the SOURCE button.
3 Select a frequency with the 4 / ¢ button.
2 Press the 6 button.
1 Press and hold the SOURCE button.
*If
is flashing, press 4 / ¢ to make the time display flash.
·When you press and hold the 4 / ¢ button, the Unit automatically searches for
broadcast stations. The search is finished when a signal is picked up. Press the button again while searching is in progress to quit the search.
Use 4 / ¢ to select a number and press the SOURCE
button to enter it. Then, you can select the next item. The
items are switched in the following order.
Button
24-hour display/12-hourdisplay → Hour → Minute → Setting
complete. (The current time is displayed.)
*If you made a mistake or the setting disappeared because of a
power failure or the like, start over from Step 1.
Function
A channel number is displayed.
3 Select your desired channel number with the 4 / ¢ button,
and press and hold the 6 button.
The channel number starts flashing.
6
Press to switch between the frequency and channel display.
¢
Press to raise the frequency or select a preset channel.
4
Press to lower the frequency or selects a preset channel.
4 While the channel number is flashing, use the 4 / ¢ button to
select the frequency of the station that you wish to register and
press the 6 button.
The selected frequency will be registered in the selected channel.
*If you made a mistake or the setting disappeared because of a power failure or the like, start
over from Step 1.
FM wire antenna
Pull the FM wire antenna out of the pocket
in the battery compartment cover and extend
the antenna along the
groove of the Unit and
in the direction where
you can get the best
radio reception.
AA battery
nListening to the channel of a broadcast station you
registered
Dock adaptor
(Supplied with the iPod or
purchased separately)
uConnecting the AC adaptor
Wall outlet
AC 120 V, 60 Hz
1 Press the 6 button while “FM” is selected.
A channel number is displayed and the signal of the registered frequency is picked up.
2 Select a channel number with the 4 / ¢ button.
VOLUME button
The signal of the frequency registered to the selected channel number is picked up.
Adjusts the volume level of the Unit.
AC adaptor (supplied)
RA-P1B : AA-R609
RA-P1W : AA-R610
Power button
nAbout the Display Indications
SNOOZE/BRIGHTNESS button
Functions used
Pressing this button displays the current time.
* If you press and hold this button while the power is turned on,
the display light turns on and off.
* Even if the power is not supplied to the Unit, the display is lit.
Displayed numbers, icons, etc.
Volume level adjustment 00 to 32
iPod
FM radio
External device
Flashes while the Unit is snoozing.
iPod
FM 87.5 to 108.0 MHz (Frequencies)
P01 to P10 (Channels)
Audio in 00 to 32 (Volume level)
Flashes when the remaining battery
level is low.
Listening to / Charging the iPod
■ Listening to the iPod
nCharging the iPod
1 Set the iPod in the Unit.
1 Connect the AC adaptor to the Unit.
·Set the dock adaptor and then set the iPod.
·Securely insert the iPod all the way into the adaptor.
*A terminal cover is covering the connecter terminal when you purchase the Unit. Remove
the cover before use.
*If you do not connect the iPod, be sure to cover the connecter terminal with the terminal
cover. Dust or the like may infiltrate the Unit and cause malfunctions.
*When you operate the iPod, support the iPod from the back side. Excessive force may
damage the connector terminal.
Setting the Timer of the iPod, FM Radio or Buzzer
*The iPod battery is not charged while the Unit is operated on battery
power supply.
nSetting the timer
2 Set the iPod to the Unit.
Button
Function
6
Playback / Pause
Press and hold this button to switch the iPod to the sleep mode.
¢
Next song / Fast forward (Press and hold.)
4
Previous song (Press this button during playback to jump back to the
beginning of the track.) / Fast rewind (Press and hold.)
Dock adaptor (Supplied with the iPod or purchased separately)
·You can remove the dock adaptor by pulling up the slot with your fingernail or
a fine-tipped tool.
·Pay attention not to injure your fingertip or damage the connector.
*If a dock adaptor was not supplied with your iPod, purchase a dock adaptor from
Apple Inc. For details, visit Apple’s website. <http://www.apple.com/>
Hour → Minute → Sound source (bb/ buzzer) → Setting complete. (The current time is
displayed.)
1 Press and hold the SOURCE button.
2 Use the 4 / ¢ button to display
button.
*See the iPod instruction manual about charging times.
and press the SOURCE
3 Select the time and so on when to start playback.
When the iPod is selected as the audio source, it automatically starts playback.
The Unit automatically starts playback.
[Sounding buzzer]
Set the timer with the power off.
Charging starts.
·The iPod is charged while any function of the Unit is used.
·The iPod is charged while the Unit is turned off.
2 Turn on the power.
3 Select “iPod” with the SOURCE button.
Lights when the timer mode is selected.
Use the 4 / ¢ button to select the setting and press the SOURCE button to enter
it. Then, you can select the next item. The items are switched in the following order.
Listening to External Devices
*If you made a mistake or the setting disappeared because of a power failure or the like, start
over from Step 1.
[Playing back from the iPod]
1 Connect an external device to the Unit.
Connect the external device to the AUDIO IN jack on the rear of the unit using a
stereo mini plug cord (not supplied).
Hour → Minute → Sound source (iPod) → Volume level when timer playback starts →
Playback time → Setting complete. (The current time is displayed.)
·The last selected track is automatically played back.
·The playback time is set in 5-minute increments from 10 to 30 minutes.
To the audio output of a CD/MD/digital
audio player, etc. or headphones terminal
[Receiving the signal from the FM radio]
Hour → Minute → Sound source (FM) → Channel is selected. → Volume level when timer
playback starts → Playback time → Setting complete. (The current time is displayed.)
2 Turn on the power.
·The playback time is set in 5-minute increments from 10 to 30 minutes.
3 Select “Audio in” with the SOURCE button.
*Register desired broadcast stations in preset channels in advance.
4 Start playback from the external device.
–2–
*You cannot set the volume level of the buzzer.
*If you do not stop the buzzer, it keeps sounding for 3 minutes.
4 Switch the ALARM switch to “TIMER PLAY.”
appears on the display.
*When the ALARM switch is switched to “TIMER PLAY”, the Unit is locked with the power off.
nStopping Timer Playback
[Pausing timer playback (Snoozing function)]
Press the SNOOZE/BRIGHTNESS button during timer playback.
Timer playback stops temporarily but it restarts after 9 minutes. This operation repeats
up to 6 time.
[Stopping the timer playback]
Press the power button during timer playback.
Timer playback stops and it restarts at the same time the next day.
nCancelling the timer
Switch the ALARM switch to “ALARM OFF.”