Dodge 2005 Stratus Coupe Automobile User Manual

care and operation
instructions
DIRECT VENT
SSDV-3328 SERIES
WARNINGS
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
• If small children are present in the home, it is
recommended that this appliance be fitted with
a screen door or screen panel kit. See Page 14
for ordering information.
WARNING: IF THE INFORMATION IN THIS MANUAL
IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY: Do not store or use gasoline
or other flammables or liquids in the vicinity of
this or any other appliance.
FOR YOUR SAFETY: What to do if you smell gas:
•DO NOT light any appliance.
•DO NOT touch any electrical switches.
•Do not use any phone in your building.
•Immediately call your gas supplier from a
neighbor’s phone. Follow your gas suppliers
instructions.
•If your gas supplier cannot be reached, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
OTL Report No. 116-F-29-5
US
A French manual is available upon request. Order P/N 725,045CF
DIRECT-VENT GAS FIREPLACE HEATERS
P/N 725,045M REV. N/C 09/2007
MODELS
Millivolt Models
Electronic Models
SSDVT-3328CNM
SSDVR-3328CNM
SSDVT-3328CNE
SSDVR-3328CNE
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
AVERTISSEMENT: ASSUREZ-VOUS DE BIEN
SUIVRE LES INSTRUCTIONS DONNÉ DANS CETTE
NOTICE POUR RÉDUIRE AU MINIMUM LE RISQUE
D'INCENDIE OU POUR ÉVITER TOUT DOMMAGE
MATÉRIEL, TOUTE BLESSURE OU LA MORT.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni
utiliser d'essence ni d'autre vapeurs ou liquides
inflammables dans le voisinage de cet appareil ou
de tout autre appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez
une odeur de gaz:
•Ne pas tenter d'allumer d'appareil.
•Ne touchez à aucun interrupteur. Ne pas vous
servir des téléphones se trouvant dans le batiment où vous vous trouvez.
•Evacuez la piéce, le bâtiment ou la zone.
•Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
•Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service dos incendies.
L'installation et service doit être exécuté par un
qualifié installeur, agence de service ou le fournisseur de gaz.
Ce manuel d’installation est disponible en francais, simplement en
faire la demande. Numéro de la pièce 725,045CF
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Congratulations!
In selecting this SUPERIOR Direct-Vent Gas Appliance you have chosen the finest and
most dependable fireplace to be found anywhere. A beautiful, prestigious, alternative
to a wood burning fireplace. Welcome to a Family of tens of thousands of satisfied
SUPERIOR Fireplace Owners.
Please read and carefully follow all of the instructions found in this manual. Please
pay special attention to the safety instructions provided in this manual. The Care and
Operation Instructions included here will assure that you have many years of dependable and enjoyable service from your SUPERIOR product.
TABLE OF CONTENTS
Introduction.......................................Page 2
General Information...........................Page 2
Gas Controls Access..........................Page 3
Operation / Care of Your Appliance....Page 4
Variable Flame Adjustment.................Page 4
Maintenance.......................................Page 5
Front Glass Enclosure Panel,
Removal and Installation..................Page 6
Install Volcanic Stone,
Embers & Logs..................................Page 7
Burner Flame Appearance & SootingPage 9
Burner Flame Adjustments.................Page 9
Millivolt Appliance Checkout..............Page 10
Electronic Appliance Checkout...........Page 10
Wiring Diagrams................................Page 11
Warranty............................................Page 11
Product Reference Information..........Page 11
Accessory Components.....................Page 13
Lighting Instructions – Millivolt.........Page 16
Lighting Instructions – Electronic......Page 18
Maintenance Schedule.......................Page 20
Troubleshooting Guide – Millivolt......Page 21
Troubleshooting Guide – Electronic...Page 22
Replacement Parts List......................Page 23
Introduction
The Fireplace models covered in this manual
are Direct-Vent sealed combustion gas fireplace
heaters designed for residential application.
Direct-Vent appliances operate with the combustion chamber completely isolated from the
indoor environment. All air for combustion is
brought in from the outside and exhaust gases
are vented through the same direct vent, co-axial
(intake/exhaust) vent system.
The Millivolt appliances have a millivolt gas
control valve with piezo ignition system provides
safe, efficient operation. If any optional accessories which require electrical power are being
installed, the electrical power must be provided
at the time of appliance installation.
The Electronic appliances have an electronic
intermittent pilot system provides safe, efficient
operation. External electrical power is required
to operate these appliances.
These appliances comply with National Safety
Standards and are tested and listed by Omni-Test
Laboratories (Report No. 116-F-29-5) to ANSI
Z21.88 (in Canada, CSA-2.33), and CAN/CGA2.17-M91 in both USA and Canada, as vented
gas fireplace heaters.
The Installation must conform to local codes
or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA
54-latest edition, or the Natural Gas and
Propane Installation Code, CSA B149.1-latest
edition. The appliance, when installed, must
be electrically grounded in accordance with
local codes or, in the absence of local codes,
the latest edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.1 - latest editions.
General Information
Note: Installation and repair should be performed by a qualified service person. The
appliance should be inspected annually by a
qualified professional service technician. More
frequent inspections and cleanings may be
required due to excessive lint from carpeting,
bedding material, etc.
It is imperative that the control compartment,
burners and circulating air passage ways of
appliance be kept clean.
S'assurer que le brùleur et le compartiment des
commandes sont propres. Voir les instructions
d'installation et d'utilisation qui accompagnent
l'appareil.
Provide adequate clearances around air openings and adequate accessibility clearance for
service and proper operation. Never obstruct
the front openings of the appliance.
These appliances are designed to operate on
natural or propane gas only. Do not use any
other fuels. The use of other fuels, or combination of fuels, will degrade the performance
of this system and may be dangerous.
These fireplaces are designed as supplemental heaters. Therefore, it is advisable to have
an alternate heat source when installed in a
dwelling.
Millivolt Models - BTU Input
Millivolt models come standard with the manually-modulated gas valve; flame appearance and
heat output can be controlled at the gas valve.
The BTU Input for millivolt models is shown
in Table 1:
Input (BTU) Manually-Modulated Gas
Valves (millivolt models)
NATURAL & PROPANE GAS
Models
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
17,500 high
13,500 low
SSDVT/R-3328
Table 1
Electronic Models Electronic models have a fixed rate gas valve.
The BTU Input for electronic models is shown
in Table 2:
Electronic Models with Fixed Rate Gas Valve
Natural and Propane Gas
Model Series
Input Rate (BTU / HR)
SSDVT/R-3328
17,500
Table 2
Gas Pressure - All Models
Tables 3, 4 and 5 show the appliances' inlet
gas pressure requirements:
Inlet Gas Supply Pressure
(all models)
Fuel #
Minimum
Maximum
Natural Gas
5.0" WC
(1.24 kPa)
10.5" WC
(2.61 kPa)
Propane
11.0" WC
(2.74 kPa)
13.0" WC
(3.23 kPa)
Table 3
Input Rate (BTU / HR)
Manifold Gas Supply Pressure
(millivolt models)
Fuel #
Low
High
Natural
Gas
(Lo) 2.2" WC
(.55 kPa)
(Hi) 3.5" WC
(.87 kPa)
Propane
(Lo) 6.3" WC
(1.57 kPa)
(Hi) 10.0" WC
(2.49 kPa)
Table 4
Manifold Gas Supply Pressure
(electronic models)
Fuel #
Manifold Pressure
Natural Gas
3.5" WC (.87 kPa)
Propane
10.0" WC (2.49 kPa)
Table 5
Test gauge connections are provided on the
front of the millivolt gas control valve, identified IN for the inlet and OUT for the manifold
side. A 1/8" NPT Test gauge connection
is provided at the inlet and outlet side of
the electronic gas control valve.
These appliances must be isolated from the
gas supply piping system (by closing their
individual manual shut-off valve) during any
pressure testing of the gas supply piping
system at test pressures equal to or less than
1/2 psig (3.5 kPa).
These appliances and their individual shut-off
valves must be disconnected from the gas
supply piping system during any pressure
testing of that system at pressures greater
than 1/2 psig (3.5 kPa).
Orifice Sizes - Sea Level to High Altitude
(All Models): These appliances are tested and
approved for installations at elevations of 0-4500
feet (0-1372 meters) above sea level using the
standard burner orifice sizes (marked with an
"*" in Table 6 ).
Burner Orifice Sizes
Elevation 0-4500 feet ( 0-1372 meters)
Natural
Gas
Propane
Gas
Model
Series
drill size (inches)
drill size (inches)
SSDVT/R-3328
#45 *
(0.048") *
* Standard size installed at factory
At the time of installation, it must be determined
if the appliance needs to be derated. Contact
your local gas supplier for deration requirements
for your area.
Deration - At higher elevations, the amount of
BTU fuel value delivered must be reduced by
either using gas that has been derated by the gas
company or by changing the burner orifice to a
smaller size as regulated by the local authorities
having jurisdiction and by the (USA) National
Fuel Gas Code NFPA 54 / ANSI Z223.1 - latest
edition or, in Canada, the CAN1-B149.1 and .2
codes - latest edition.
Burn-in Period
During the first few fires of this appliance there
will be some odor due to the curing of the
paint and burning off of lubricants used in the
manufacturing process.
On millivolt systems, the piezo igniter, HI/LO
flame adjustment knob, and pilot and main
gas OFF/ON control knob are located below
the glass panel enclosure. The gas valve for
electronic systems is also located below the
glass enclosure panel. See Figure 1.
Reinstalling Control Compartment Door:
To reinstall, insert the hook catches on each side
of the door into the corresponding slots in the
control compartment opening, then gently push
forward and side down until it locks in place.
Lift the Lower Control
Compartment Door
OPENING CONTROL
up and pull out to
COMPARTMENT DOOR remove.
Hook Catch
Control Valve
Up
Depending on your use, the burn-in period may
take a few hours or a few days.
KEEP YOUR HOUSE WELL VENTILATED
DURING THE CURING PROCESS. THE ODOR
AND HAZE EMITTED DURING THE CURING
PROCESS CAN BE QUITE NOTICEABLE AND
MAY SET OFF A SMOKE DETECTOR.
If an optional blower is installed, Do not turn it
on during the Burn-In period.
A white film may develop on the glass front
during the first few fires as part of the curing
process. The glass should be kept clean during
the first two weeks of use to prevent the film from
baking on (making it very difficult to remove).
See Cleaning Glass on Page 5.
Gas Controls / Control Compartment
Access
NOTE: The top louvered panel and the bottom
louvered control panel door remove and install
the same way as follows:
The gas controls can be found behind the control
compartment access door.
Removing Control Compartment Door:
Open the door by gently lifting it upward until
the hook catches on both sides clear the locating
slots. Then pull door out to remove.
Table 6
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Out
Lower Control
Compartment Door
Figure 1
Operation of millivolt and electronic gas control systems are different. Before lighting and
operating your appliance determine if you have
a millivolt or electronic appliance. Familiarize
yourself with the gas control valve that your
appliance uses. Refer to Figure 1 for access
to the gas control valve.
Millivolt Appliances - Appliances with
Millivolt systems will be fitted with the gas
control valve shown in Figures 4 or 5.
Electronic Appliances - Appliances with
electronic systems will be fitted with the
electronic valve shown in Figure 3.
Millivolt Appliances - To light millivolt appliances refer to the detailed lighting instructions
found on Pages 16 & 17 . Millivolt appliance
lighting instructions may also be found on the
pull out lighting instruction labels attached to
the gas control valve.
Millivolt appliances are fitted with an OFF/ON
Rocker Switch located behind the control
compartment access door, below the appliance front glass enclosure panel (see Figure 1
for location). Once the pilot is lit, the OFF/ON
rocker switch will control the appliance OFF/ON
burner operation. To operate: Toggle the switch
between its ON and OFF positions.
If your millivolt appliance is equipped with an
optional remote switch kit (wall switch, remote
control or wall thermostat) and the pilot is lit,
the appliance main burner may be turned on
and off using the optional switch. When using
an optional remote switch, turn off the standard
OFF/ON switch.
Operation and care of your
appliance
The standard controls for appliance operation
are located behind the panel below the appliance front glass enclosure panel (see Figure
1). Optional control switches are also available
(see Page 13 - Remote Wall Switch, Remote
Control or Wall Thermostat).
Note: To prevent excessive resistance in burner
circuit (which can cause burner operation problems), only one burner control switch should be
wired to valve. Therefore, if an optional control
switch is installed, the standard Off/On switch
and wires should be removed.
If your electronic appliance is equipped with an
optional remote wall switch or remote control kit
the appliance main burner may be turned on and
off with the wall switch or remote control.
2.During the first initial burns of these appliances, there will be some odor emitted (see
Burn-In Period on Page 3 ).
3.Keep the lower control compartment clean
by vacuuming or brushing at least twice a
year. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
materials, pet hair, etc. It is very important
that the control compartments, burners
and circulating air passageways of the
appliance are kept clean.
4.Always turn off gas to the pilot (millivolt
appliances) and let the appliance cool down
before cleaning. Before re-lighting, refer to
the lighting instructions in this manual. Lighting instructions may also be found on the
pull out lighting instruction labels attached
to the gas control valve.
5.Always keep the appliance area clear and
free from combustible materials, gasoline
and other flammable liquids.
6.Remember, Millivolt appliances have a continuous burning pilot flame. Exercise caution when
using products with combustible vapors.
If your electronic appliance is not equipped
with a wall switch or remote control, the main
burner must be turned off and on with the gas
control switch. Toggle the switch from ON to
OFF to operate the main burner.
Variable Flame Height Adjustment
(Millivolt Appliances only)
1. All Millivolt appliances are equipped with a
variable gas control valve. Flame height for
these models may be adjusted through a
range between fixed low and high settings
while the appliance is in operation.
Adjust the flame height as desired after lighting
the appliance by rotating the variable adjustment
control knob (HI/LO) located on the front of the
valve (refer to Figures 4 & 5).
SIT Millivolt Gas Valve
SIT Gas Valve
HI/LO Variable Flame Manifold Pressure Tap
Height Adjustment
Inlet Pressure Tap
Gas
Inlet
IN
OUT
TPTH
HI
TH
LO W
OT
ON
ON
OFF
Honeywell Millivolt Gas Valve
Manifold Pressure
Tap
Inlet Pressure Tap
Piezo Igniter
P IL
Gas
Outlet
ON
LO
OT OF F
OFF
HI/LO Variable
Flame Height Optional Burner OFF/ON
Adjustment
Rocker Switch
Figure 5
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
ON
Piezo Igniter
ON
IN
Main Gas
Control Knob
Figure 4
Inlet
Pressure
Port
PSI
TPTH,TP & TH
Optional Blower OFF/ON Rocker Switch
Piezo Igniter
ON / OFF Switch
Electronic Gas
Control Valve
Terminals
OFF/PILOT/ON
Optional Burner OFF/ON
Rocker Switch
IGNITER
OFF
Piezo Igniter
HI
OFF
ON
CONTROL
Figure 3
Gas
Outlet
OFF
Honeywell Electronic Gas Valve
PIL
Electronic Appliances To light electronic appliances refer to the detailed
lighting instructions found on Pages 18 & 19
of these instructions. Electronic appliance
lighting instructions may also be found on the
pull out lighting instruction labels attached to
the gas control valve.
Pilot Adjustment
Screw
ON
Figure 2
it
Honeywell
Gas Valve
Sit and Honeywell Millivolt Gas Valve
Showing Piezo Igniter Location (Each Unit is
Equipped with Only One of these Gas Valves)
Manifold Pressure
Port
O FF
P IL O T
Piezo Igniter
TP
Shown with control
compartment door
removed
Main Gas
Control Knob
OFF/PILOT/ON
Optional Blower OFF/ON
Rocker Switch
Gas
Inlet
MAINTENANCE
(See Maintenance Schedule, Page 20)
Refer to the maintenance schedule for maintenance
tasks, procedures, periodicity and by whom they
should be performed. Always verify proper operation of the appliance after servicing.
Before re-lighting the fireplace, refer to the
lighting instructions in this manual. Instructions are also found on pull-out panels
located below the glass door in the control
compartment.
WARNING
Turn off gas and electrical power
before servicing the appliance.
CAUTION
Wear gloves and safety Glasses
for protection while doing
required maintenance.
IMPORTANT
Always verify proper operation
after servicing.
Inspect Venting System
The appliance and venting system should be
thoroughly inspected before initial use and at
least annually by a qualified service technician
(inspection should include ensuring that exhaust
or intake passages are unobstructed and vent
components are properly assembled and not
damaged). If the venting system is disassembled
for any reason, a qualified service technician
should follow vent installation instructions for
proper reassembly and proper sealing of the
venting system components. However, more
frequent periodic inspections and cleanings
should be performed by the homeowner.
Clean Lower Control Compartment
Keep lower control compartment clean by vacuuming or brushing it out at least twice a year (also
clean the air venturi with a brush or wire). More
frequent cleaning may be required due to accumulation of lint from carpeting, bedding materials, pet
hair, spider webs, etc. It is very important that
control compartments, burners, circulating air
passageways and air venturi on the appliance
are NOT obstructed in any way.
IMPORTANT
It is imperative that the control
compartment, burners and
circulating air passage ways of
appliance be kept clean.
Cleaning Glass
(see Front Glass Enclosure Panel, Removal and
Installation on Pages 6).
Note: Clean glass after first two weeks of operation (after Burn-In period is over) and then only
when necessary and when the fireplace is cool.
Wipe surface with clean, dampened, soft cloth.
Follow with dry, soft towel as desired. Take care
not to scratch the glass surface.
The viewing glass should be cleaned periodically to
remove any build-up caused from the following:
IMPORTANT
Do not use abrasive cleaners
on glass. Never clean the glass
when it is hot.
• During start-up, it is normal for condensation to form on the inside of the glass (this
condensation and fog will usually disappear
in a few minutes). The moisture can cause
lint, dust and other airborne particles to cling
to the glass surface.
• Initial curing of the high temperature paint
and burning off of lubricants used in the
manufacturing process may result in a film
on the glass.
• A white coating may form on the glass as a
result of impurities and minerals in the fuel.
It is recommended that the glass be cleaned
two or three times during each heating season,
depending on the circumstances present. The
following cleaning solutions are approved for use
to clean glass:
• Non-ammonia based household cleaner
• 50%-50% mix of white vinegar & water
• Gas fireplace/stove glass cleaner
Inspect Glass Gasket - Visually inspect the
gasket on the backside of the glass enclosure
panels. The gasket surface must be clean, free
of irregularities and seated firmly.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Clean Logs And Burner
Carefully remove the logs (use care when handling the fiber logs, as they become quite fragile
after curing). Vacuum out any foreign matter
(lint, carbon, etc). on the burner. Ensure the
burner ports are “open.” Remove any carbon
deposits from the under side of the logs using
a vacuum cleaner, or a soft bristled brush (i.e.
paint brush). Note: Improper positioning of
logs can create carbon build-up and will alter
the performance of the appliance.
Replacing Logs If the logs become damaged by accident or improper handling and need replacement, use only
the proper replacement logs from manufacturer
(see Page 23 for ordering information).
Re-Install Embers, Logs and Volcanic Stone
- Carefully follow placement instructions on
Pages 7 to 9 ). All logs should fit onto corresponding pins and/or log stoppers. This will
ensure a proper flame and safe combustion.
Inspect Wiring
Refer to wiring diagrams on Page 11.
WARNING
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper operation
after servicing.
Inspect and clean all wire connections. Ensure
that there is no melting or damage. Inspection
should include:
• Terminals at the Valve
• OFF/ON Switch
• (Optional Control Switch) Wall Thermostat,
Remote Control or Remote Wall Switch Kit
Inspect Burner Flame Appearance
Ensure that the burner flame appearance
resembles the flame shown in Figure 9 and
as described in Flame Appearance and Sooting on Page 9. The Homeowner must contact
a qualified service technician at once if any
abnormal condition is observed.
Small Area Paint Touch-up
The finish of the appliance is a high quality powdercoat. Only use factory supplied
powdercoat paint kit for touch-ups. Paint is
available at your local authorized LHP dealer,
cat. no. 90L74. Never attempt to paint a hot
fireplace.
Do not attempt to repaint the appliance until the
finish is completely cured (see Burn-In Period
on Page 3). If the surface later becomes stained
or marred, it may be lightly sanded and touched
up with spray paint.
Front Glass Enclosure Panel, Removal
and Installation
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken. Replacement of
the glass should be done by a
licensed or qualified service
technician.
WARNING
Do not attempt to substitute the
materials used on this door, or
replace cracked or broken glass
with any materials other than
those provided by the appliance
manufacturer.
WARNING
WARNING
The glass door of this appliance must only be replaced as
a complete unit as provided by
the manufacturer. Do not attempt
to replace broken, cracked or
chipped glass separately.
These are direct-vent appliances. They are
designed to operate only when the front glass
enclosure panel is installed. Generally the front
glass enclosure panel should not be removed except to gain access to the components within the
firebox, and the appliance may only be operated
without the front glass enclosure panel in place
for very brief periods of time during appliance
checkout and adjustment.
Note: The flame appearance will be diminished while the front glass enclosure panel is
removed.
During this appliance checkout and adjustment period, a potential safety hazard exists
- EXERCISE EXTREME CAUTION to prevent
the occurrence of any burn injuries from the
exposed flames or hot surfaces. Also note, that
while the front glass enclosure panel (or any of
the panels) is removed, the flame appearance
will appear to be smaller than normal.
Handle this glass with extreme
care! Tempered glass is susceptible to damage – do not scratch
or handle roughly while reinstalling the glass door frame.
Top Flange on
Glass Door
Glass Door
WARNING
1.Remove the top louver assembly by lifting
it up and pulling it out.
2.Remove the control compartment access
door (see removal instructions on Page 3
- Removing Control Compartment Door).
3.Locate the two (2) latches at the top of the
control compartment. To disengage the two
latches from the bottom vee-flange of the
glass enclosure panel, reach for the handles
located towards the back of the latches and
pull the handles down toward the front of
the appliance.
4.Swing the bottom of the door out and raise
it slightly to lift the top flange of the door
frame away from the appliance.
Installing Glass Enclosure Panels
(see Figure 6)
1. Visually inspect the gasket on the backside
of the glass panel. The gasket surface must
be clean, free of irregularities and seated
firmly.
2.Position the glass enclosure panel in front
of the firebox opening at a 45 degree angle
and engage the top flange over the lip at the
top of the firebox opening. See Figure 6.
3. Swing the glass enclosure panel down and
back. Ensure the gasket seats evenly as the
panel draws shut. Engage the Vee-flange at
the bottom of the panel with the latches and
close the latches to secure the panel.
4.Reinstall top louver assembly and control
compartment door see installation instructions on Page 3, Reinstalling Control
Compartment Door).
Do not attempt to touch the front
enclosure glass with your hands
while the fireplace is in use.
Bottom Vee-flange
Glass Door
Firebox Floor
Glass Door Latch
Figure 6 - INSTALLING GLASS DOOR
Removing Glass Enclosure Panels
(see Figure 6)
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTALL Logs, VOLCANIC STONE and
GLOWING EMBERS
Carefully position the ceramic fiber logs and
twigs over the burner according to the following
steps, while referring to Figure 7.
1.Set the rear log on the raised log support
brackets at the rear of the firebox, fitting
the slots in the logs over the brackets.
2.Position the front log with the pins for the
two side twigs in the up position, and the
two vertical burner tabs recessed into the
two notches at the rear of the log. Check
for recessing of brackets into log notches
(by touch) to verify correct log placement.
3.Insert the alignment hole of the left twig over
the front log's left pin. Rotate the left twig
until it just touches the edge of the ember
bracket.
4.Insert the alignment hole of the right twig
over the front log's right pin. Rotate the
right twig until it almost touches the front
panel glass.
Note: Proper twig placement is critical in the
gaps between the flame peaks and should be
positioned so that at no time they impinge
the flames.
Glowing Ember/Volcanic Stone Placement
Remove the replacement rockwool (Glowing
Embers) from the packaging and tear into
quarter size pieces (see Figure 8 ).
WARNING
Logs get very hot and will remain
hot up to one hour after gas
supply is turned off. Handle
only when logs are cool. Turn
off all electricity to the appliance before you install grate
and logs.
WARNING
This appliance is not designed
to burn wood. Any attempt to
do so could cause irreparable
damage to appliance and prove
hazardous to your safety.
Separate into Quarter
Size (separate) Pieces
WARNING
DO NOT attempt to install the logs
until the appliance installation
has been completed, the gas line
connected and tested for leaks
and the initial burner operation
has been checked out.
WARNING
The size and position of the log set
was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt
to use a different log set in the
fireplace will void the warranty
and will result in incomplete
combustion, sooting, and poor
flame quality.
Bag of Glowing
Embers (rockwool)
Figure 8 - Glowing Embers
REFERENCE
Firebox Accessories / Parts
Cat. No.
Model No.
88L53
FGE
80L42
FDVS
Description
Bag of Glowing Embers
(1 oz. rockwool)
Bag of Decorative
Volcanic Stone
Table 8
Spread rockwool (quarter-sized pieces) on and
along the length of the burner screen. Do not
use more than is necessary. To many quartersized pieces on the front burner section will
cause poor combustion.
When properly positioned, the rockwool will
unevenly cover approximately 85% of the
burner screen, with no appreciable gaps or
openings.
To install Decorative Volcanic Stone, mound up
a portion of the volcanic stone in front of the
burner in a pattern to suite individual taste.
Figure 7 - Log Set (Shown With Optional Log Rack)
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
NOTES:
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Burner Adjustments
(QUALIFIED TECHNICIANS ONLY)
Flame Appearance and Sooting
Proper flame appearance is a flame which is
blue at the base and becomes yellowish-orange
in the body of the flame. When the appliance
is first lit, the entire flame may be blue and
will gradually turn yellowish-orange during
the first 15 minutes of operation. If after a
short period the flame stays lowered blue, or
if the flame is orange with evidence of sooting
(black tip), the air shutter opening may need
to be adjusted.
If the air shutter opening is closed too far,
sooting may develop. Sooting is indicated
by black puffs developing at the tips of very
long orange flames. Sooting results in black
deposits forming on the logs, appliance inside
surfaces and on exterior surfaces adjacent
to the vent termination. Sooting is caused
by incomplete combustion in the flames and
lack of combustion air entering the air shutter
opening. To achieve a warm yellowish-orange
flame with an orange body that does not soot,
the shutter opening must be adjusted between
these two extremes.
Air Shutter Adjustment Guidelines
• If there is smoke or soot present, first
check the log set positioning to ensure that
the flames are not impinging on any of the
logs. If the log set is properly positioned
and a sooting condition still exists, then the
air shutter opening should be increased.
• The more offsets in the vent system, the larger
the air shutter opening will need to be.
• An appliance operated with the air shutter
opened too far, may have flames that appear
blue and transparent. These weak, blue and
transparent flames are termed anemic.
• Propane models may exhibit flames which
candle or appear stringy. If this is present
and persists, adjust the air shutter to a more
closed position, then operate the appliance
for a few more minutes to ensure that the
flame normalizes and the flames do not
appear sooty.
The following chart is provided to aid you in
achieving the correct air shutter adjustment
for your installation.
Air Shutter Adjustment Guidelines:
Amount of
Primary Air
Flame
Color
Air Shutter
Adjustment
If air shutter is
closed too far
Flame will
be orange
Air shutter
gap should be
increased
If air shutter is
open too far
Flame will
be blue
Air shutter
gap should be
decreased
Figure 9 - Burner Flame Appearance Model SSDV-3328 Series
Burner Air Shutter Adjustment Procedure
1. Locate adjustment rod and adjust air
shutter to the standard setting as shown
in Figure 10 (adjustment rod is located
in the lower control compartment).
Note: Rotating the adjustment rod counterclockwise increases air and clockwise
decreases air.
2.Light appliance (follow lighting procedure on
lighting label in control compartment or see
pages 16 and 18).
3.Allow the burner to operate for at least
15 minutes while observing the flame
continuously to ensure that the proper
flame appearance has been achieved (see
Figure 9). If the following conditions are
present, adjust accordingly.
• If flame appears weak or sooty, adjust
the air shutter, incrementally, to a more
open position until the proper flame
appearance is achieved.
• If flame stays lowered blue, adjust the
air shutter, incrementally, to a more
closed position until the proper flame
appearance is achieved.
4.Leave the control knob (off/pilot/on) in the
ON position and the burner OFF/ON switch
OFF (& remote switches, if applicable).
5.When satisfied that the burner flame appearance is normal, close the lower control
compartment door.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
WARNING
Air shutter adjustment should
only be performed by a qualified
professional service technician.
WARNING
Ensure front glass panel is in place
and sealed during adjustment.
CAUTION
The air shutter door and nearby
appliance surfaces are hot. Exercise caution to avoid injury while
adjusting flame appearance.
CAUTION
Carbon will be produced if the air
shutter is closed too much. Any
damage due to carboning resulting from improperly setting the
air shutter is not covered under
the warranty.
Burner Air Shutter Adjustment
Electronic Appliance Checkout
SIT MILLIVOLT PILOT ASSEMBLY
Proper Pilot Flame Appearance
Igniter Rod
Hood
Adjustment Setscrew
Adjustment Rod Up
(Fully Open Position)
Thermocouple
Burner Tube
3/8" Min.
(9 mm)
Air Shutter
Adjustment Rod Down
(minimum air opening
position)
Ref. Air shutter Patent:
U.S. Pat. 5,553,603
Main Burner Factory Air Shutter
Opening Setting - Inches (millimeter)
Model
SSDVT-3328
SSDVR-3328
Natural
Gas
Propane
Gas
1/32
(0.826 mm)
5/16
(7.94 mm)
Figure 10
The top 3/8" (10 mm) at the pilot generator
(thermopile) and the top 1/8" minimum (tip)
of the quick drop out thermocouple should be
engulfed in the pilot flame. The flame should
project 1" (25 mm) beyond the hood at all three
ports. See Figure 11 or 12.
ELECTRONIC PILOT ASSEMBLY
Proper Pilot Flame Appearance
Proper Flame
Adjustment
Pilot
Nozzels
Pilot
Nozzels
Thermopile
Figure 11
Thermocouple
Igniter Rod
Hood
Ground
Electrode
Hot Surface
Igniter
Proper Pilot Flame Appearance
1/8" Min.
(3 mm)
3/8" to 1/2"
(9 -13 mm)
Flame Rod
HONEYWELL MILLIVOLT PILOT ASSEMBLY
Millivolt Appliance Checkout
The pilot flame should be steady, not lifting
or floating. Flame should be blue in color with
traces of orange at the outer edge.
To light the burner, refer to the lighting instructions on Pages 18 & 19. Ensure the igniter
lights the pilot. The pilot flame should engulf
the flame sensor as shown in Figure 13.
Figure 13
3/8" Min.
(9 mm)
Pilot
Nozzels
Thermopile
Figure 12
To light the burner, refer to the lighting instructions on Pages 16 & 17.
With proper care and maintenance, your appliance will provide many years of enjoyment. If
you should experience any problem, first refer
to the troubleshooting guide in this manual.
If problem persists, contact your Lennox
distributor.
WIRING DIAGRAM
The wiring diagrams are provided here for
reference purposes only (Figures 14 & 15 ).
This information is also provided on schematics found on pullout lighting instruction labels
located within the control compartment attached
to the gas control valve.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS.
WIRING ERRORS CAN CAUSE IMPROPER AND
DANGEROUS APPLIANCE OPERATION.
10
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Wiring Diagrams
Wiring diagrams are provided here for reference purposes only. This information is also
provided on schematics attached directly to the
appliance on a pullout panel located within the
control compartment.
Electronic Wiring Diagram (Honeywell) Showing Blower Wiring for Optional FBK-100, FBK-200 & FBK-250 Kits
Schematic Representation Only
Auxiliary View A
J-Box Wiring when
using unit mounted
relay module.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous appliance operation.
If any of the original wire as supplied must
be replaced, it must be replaced with Type
AWM105 C - 18 gage wire.
*OFF/ON Switch
(Integral with
Gas Valve)
TH
Factory
Wired
Standard OFF/ON Switch
* Optional Kits Installed - OFF/ON wall switch,
wall thermostat or remote control receiver.
Note: Turn the appliance-mounted OFF/ON
burner control switch to the OFF position if
any of these kits are installed.
Figure 14
G BK
Hot side
of Outlet
Igniter
Connector
BL
BL
Transformer
BK
R
BK
W
GROUND
BL
24 V
Secondary
BK
120 VAC
Primary
BK = BLACK BL = BLUE
R = RED
W = WHITE
G = GREEN
TH
TP
TP
Field Wired
BK
W
G
Break off Tab
Honeywell
Electronic
Gas
Valve
Figure 15
*Optional Switch
120
VAC
Optional Blower
Pilot Burner
Assembly
Optional Control Switch
Thermopile
Outlet Box Green
Ground Screw
Junction Box
Millivolt Wiring Diagram
Schematic Representation Only
Relay Module C/W FBK-250 only. Plug blower
into J-Box receptacle for FBK-100 or FBK-200
application. View A for J-Box wiring.
120 VAC
BK
W
G
CAUTION
Wall Mounted Blower Speed Control Switch or
ON/OFF Switch for Blower Kit (optional)
Field Wired
Factory
Wired
Warranty
Your gas appliance is covered by a limited twenty
year warranty. You will find a copy of the warranty accompanying this manual. Please read
the warranty to be familiar with its coverage.
Retain this manual. File it with your other documents for future reference.
Product reference information
We recommend that you record the following
important information about your fireplace.
Please contact your Superior dealer for any
questions or concerns. For the number of your
nearest Superior dealer, please call:
1-800-9-LENNOX.
Visit us at www.Lennox.com
Your Fireplace's Model Number_________________________________________
Your Fireplace's Serial Number_________________________________________
The Date On Which Your Fireplace Was Installed____________________________
The Type of Gas Your Fireplace Uses_____________________________________
Junction
Box
R
White Wire
to Opposite
Side (neutral)
* Leave the OFF/ON switch, which is
integral with the gas valve, in the ON
position.
**Optional Control Switches: Wall
Switch, Wall Thermostat or Remote
Control Receiver.
Notes:
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
- 18 gage wire ONLY.
2. 120 VAC, 60 Hz - Less than 3 Amps.
Caution: label all wires prior to
disconnection when servicing controls.
Wiring errors can cause improper and
dangerous operation.
Replacement parts
A complete parts list is found at the end of
this manual. Use only parts supplied from the
manufacturer.
Normally, all parts should be ordered through
your Lennox distributor or dealer. Parts will be
shipped at prevailing prices at time of order.
When ordering repair parts, always give the
following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the installation or application
of this system, please contact your distributor,
or Lennox directly:
LHP
1110 West Taft Avenue
Orange, CA 92865
Your Dealer's Name _ ________________________________________________ NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
11
NOTES:
12
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Accessory Components
Product Reference Information
Cat.
No.
Model
Ship.
Wt.(lbs)
Ship.Vol.
(inches)
H6898
SSDVT-3328CNM
115 lbs
37W x 17D x 36H
(13.1 cu.ft).
H6899
SSDVT-3328CNE
115 lbs
37W x 17D x 36H
(13.1 cu.ft).
H6896
SSDVR-3328CNM
115 lbs
37W x 17D x 36H
(13.1 cu.ft).
H6897
SSDVR-3328CNE
115 lbs
37W x 17D x 36H
(13.1 cu.ft).
Remote Control Kit, Standard
Cat. No.
Model No.
H0249
RCL
Description
Remote Control System
(Standard)
Standard Remote Control System
The Model RCL (Standard) Remote Control System,
features a simplistic OFF/ON control function for the
fireplace. This model includes a hand-held transmitter,
a remote receiver with wall-mount cover plate and
all hardware required to install the unit. The remote
receiver can be wall or hearth mounted.
White Wall Switch Kit
Cat. No.
Model No.
Description
85L87
FWSK
OFF/ON Wall Switch Kit
OFF/ON Wall Switch Kit
The OFF/ON wall switch kit may be used to control
the operation of the fireplace burner. Install the
OFF/ON wall switch in a convenient location near
the fireplace.
The transmitter has ON and OFF functions that are
activated by pressing either button on the face of
the transmitter. When a button on the transmitter
is pressed, a signal light illuminates briefly to verify
that a signal has been sent.
The Model RCL is designed to operate with all millivolt ignition systems, as well as electronic ignition
systems. It may be installed with use for either
natural gas or propane gas appliances. The RCL
offers ease of installation and allows you to execute
on-off commands to the fireplace effortlessly with
one simple motion.
Remote Control Kit, Deluxe
Cat. No.
Model No.
Description
H0251
RCL-STAT
Remote Control System
(Deluxe)
Deluxe Remote Control System
The Model RCL-T (Deluxe) Remote Control System
has all of the features of the standard system along
with an added easy to read LCD screen which presents
access to many enhancements, including; battery
power level indicator, timer, mode of operation,
thermostatic display including room temperature in
either metric of English units, flame indicator and
clock. Fully programmable, the Model RCL-T allows
for virtual command over nearly all operational and
temperature variables, using the hand held remote
control transmitter.
The Model RCL-T (Deluxe) remote control system
is installed in the same manner as the standard
system, may be operated with electronic and millivolt systems with either natural gas or propane gas.
The RCL-T comes complete with detailed operating
instructions.
The Model RCL comes complete with detailed operating instructions.
Rocker Switch Kit
Cat. No.
80L41
Model No.
FRS
Square Log Rack
Description
Rocker Switch Kit
Unit-Mountable Rocker Switch
This rocker switch kit can be installed directly in
the gas valve mounting bracket (millivolt gas valve
equipped fireplaces) to provide On/Off operation in
lieu of a wall switch.
Wall Thermostat, Millivolt
Cat. No.
Model No.
Description
99L59
DLR-4
Decorative Log Rack
Cat. No.
Model No.
H4635
DWTK
Description
Digital Wall
Thermostat Kit
Decorative Log Rack
The decorative log rack provides the look of a wrought
iron log rack. The rack installs easily in front of the
log set with two screws.
Digital Wall Thermostat
The digital wall thermostat kit provides temperature
control for optimum comfort.
Note: Some discoloration of the grate can be expected
with fireplace operation.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
13
Accessory Components
Interior Brick Liner Kits
Rear Vent
Top Vent
Cat. #
Model
Cat. #
Model
99L54
BLK-4R
99L53
BLK-4T
Models
Where Used
SSDV-3328
Interior Brick Liner Kits
The brickade liner kits include tan stamped sheetmetal panels for the rear and side walls of the firebox. The
panels have brick-like features in relief. These kits can be retrofitted into previously installed appliances.
Decorative Arch Screen Panel Kits
Cat. No.
Model No.
Models Where Used
H3592
DASPK33TI
SSDV-3328
Decorative Arch Screen Panel Kit
This easy to install optional screen installs over the
standard glass enclosure panel to provide protection
from direct contact with the hot glass surface. These
screen panels cannot be used in conjunction with
the arch door kits or door frame kits.
Eyebrow Hood Kits
Polished Brass
Brushed Stainless
Cat. #
Model
Cat. #
Model
99L64
HK-4B
99L65
HK-4BS
Models
Where Used
SSDV-3328
These hood kits replace the standard hood that comes with
these fireplaces.
Polished Brass & Brushed Stainless Hood Kits
Attractive hoods are available in two styles. These hoods are designed to be fitted to the glass viewing sides of
the appliance. In addition to providing an aesthetically pleasing appearance to your appliance installation, the
hood reduces heat effects to decorative mantles and finish materials located above the fireplace opening. The
hood kit replaces the standard hood that comes with these appliances and snaps into place. These kits can be
retrofitted to previously installed appliances.
4 Piece Door Trim Kits
Polished Brass
Screen Panel Kits
Cat. No.
Model No.
99L55
SPK4
Models Where Used
SSDV-3328
Cat. #
Model
Cat. #
Model
99L62
DFK-4B
99L63
DFK-4BS
Models
Where Used
SSDV-3328
Door Frame Kits
A decorative door frame kit is available for use with these appliances. It is designed to attach directly to the front face
of the appliance at the four edges of the glass enclosure panel resulting in the appearance of a picture frame.
Screen Panel Kit
This easy to install optional screen installs over the
standard glass enclosure panel to prevent direct
contact with the hot glass surface. These screen
panels cannot be used in conjunction with the arch
door kits or door frame kits.
Brushed Stainless
* Assembled 8-Piece Louver Kits
Polished Brass
Brushed Stainless
Cat. #
Model
Cat. #
Model
H1522
LK-400B
H1523
LK-400BS
Models
Where Used
SSDV-3328
* Superior Nameplate Logo, 56L93, is not included.
Polished Brass & Brushed Stainless Louvers Kits
These kits include a top 4-louver assembly and a bottom 4-louver assembly. They provide a touch of elegance.
These kits can be retrofitted to previously installed appliances.
14
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Accessory Components
Arch Door Kit - Polished Brass
Cat. No.
Model
Fireplace Model
99L56
ADK-4B
SSDV-3328
Arch Door Kit - Brushed Stainless Steel
Cat. No.
Model
Fireplace Model
99L57
ADK-4BS
SSDV-3328
3 Piece Trim Kit
Cat. No.
Arch Door Kits
The arch door kits are easy to install and do not require hardware to attach them to the standard door frame.
The decorative arch kits can not be used in conjunction with the screen panel kit.
Model No.
Description
H0453
TK33PB3
33” Polished Brass, 3328
H1813
TK33BS3
33” Brushed Stainless, 3328
H4820
TK33C3
33” Charcoal, 3328
Door Frame Kits
A decorative door frame kit is available for use with
these appliances. It is designed to attach directly to the
front face of the appliance at the top and side edges of
the glass enclosure panel.
2- Piece Door Frame Kits
Polished Brass
Brushed Stainless
Cat. #
Model
Cat. #
Model
17M28
DTK-4B
17M29
DTK-BS
Models
Where Used
SSDV-3328
2-Piece Door Trim Kits
These kits are designed to attach directly to the front face of the fireplace at the top and bottom edges of the
glass enclosure panel.
Decorative Firebox Accessories
(all models)
Cat. No.
Touch-Up Paint Kits
(all models)
Cat. No.
Model No.
Description
90L73
FTPK-B
Touch-Up Paint (Black)
PA I N T
Touch-Up Paint Kit
Repair of minor scratches and discoloration of the appliance charcoal painted surfaces may be accomplished
with the touch-up paint kit.
Model No.
88L53
FGE
80L42
FDVS
Description
Bag of Glowing Embers
(1 oz. rockwool)
Bag of Decorative
Volcanic Stone
Bag of Glowing Embers
Bag of Volcanic Stone
Replacement ember materials or volcanic stone are
available for use with these appliances. Order kits as
part of the periodic maintenance of the appliance.
Forced Air Blower Kits
Cat.
No.
Model No.
Description
80L84
FBK-100
Blower, Standard
(single speed)
80L85
FBK-200
Blower, Variable Speed
(w/wall-mounted switch)
80L86
FBK-250
Blower, Variable Speed
(w/unit-mounted switch)
Forced Air Kit
The FBK-100 blower provides constant velocity forced air circulation. The FBK-200 assembly with variable
speed, wall-mountable switch provides variable speed forced air circulation. The FBK-250 assembly with
variable speed unit-mountable switch, also provides variable speed forced air circulation.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
15
Lighting Instructions – HONEYWELL AND SIT Millivolt GAS VALVE
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A. This appliance has a pilot which must be lighted with a piezo
igniter. When lighting the pilot, follow these instructions
exactly.
B. BEFORE OPERATING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•Extinguish any open flame.
•Open windows.
•Do not light any appliance.
•Do not touch any electrical switches.
•Do not use any phone in your building.
•Immediately call your gas supplier from a neighbor’s
phone.
•If your gas supplier cannot be reached, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
do not try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or an explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
LIGHTING INSTRUCTIONS
1.STOP! Read the safety information above on this Page.
2. Access the lower control compartment.
7. Push in gas control knob slightly and turn counterclockwise
to “PILOT.”
HONEYWELL
3. Turn remote wall switch to “OFF.”
4. Verify main line shut-off valve is open.
5. Push in gas control knob slightly and turn clockwise
to “OFF.”
IGNITER
T FF
LO O
PI
HONEYWELL
MILLIVOLT
GAS VALVE
ON
LO
HI
IN
OUT
TPTH
TP
HI
TH
LO W
O FF
6. Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow “B” in the safety information above on this Page. If
you do not smell gas, go to the next step.
it
PIL O T
SIT
MILLIVOLT
GAS VALVE
ON
PIL
OT
IGNITER
Note: Knob cannot be turned from “PILOT” to “OFF”
unless the knob is pushed in slightly. Do not force.
8. Push in control knob all the way and hold in.
Immediately light the pilot by triggering the
spark igniter (pushing the button) until pilot
lights. Continue to hold the control knob in
for about 1 minutes after the pilot is lit.
Release knob and it will pop back up. Pilot
should remain lit. If it goes out, repeat steps
5 through 8.
• If knob does not pop up when released,
stop and immediately call your service
technician or gas supplier.
MILLIVOLT PILOT
SIT
MILLIVOLT PILOT
• If pilot will not stay lit after several tries,
turn the control knob to “OFF” and call
your service technician or gas supplier.
9. Turn gas control knob counterclockwise
to “ON.”
10. Close lower control compartment.
TO TURN OFF GAS TO APPLIANCE
1. Turn remote wall switch “OFF.” The pilot will remain lit for
normal service.
4. Depress gas control knob slightly and turn clockwise
to “OFF.” Do not force.
2. For complete shutdown, turn remote wall switch to “OFF.”
5. Close lower control compartment.
3. Access the lower control compartment.
16
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT HONEYWELL ET SIT
POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE
AVERTISSEMENT
NE SUIVEZ
SUIVEZPAS
PASCES
CESINSTRUCTIONS
INSTRUCTIONSÀ LA
À LA
LETTRE,
IL POURRAIT
S’EN
SUIVRE
UN INCENDIE
OU
AVERTISSEMENT:: SI
SI VOUS
VOUS NE
LETTRE,
IL POURRAIT
S’EN
SUIVRE
UN INCENDIE
OU UNE
UNE
EXPLOSION
CAUSANT
DES
DOMMAGES
MATÉRIELS,
DES
BLESSURES
CORPORELLES
OU
MÊME
DES
PERTES
DE
VIE.
EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.
A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un
allumeur piézo-électrique. Lorsque vous allumez la veilleuse, suivre
exactement ces instructions.
B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez aucune
odeur de gaz autour de l’apareil ainsi que près du sol; certains gaz, étant
plus lourds que l’air, descendent au niveau du sol.
VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE ODEUR
DE GAZ:
• Éteignez toute flamme visible.
•
Ouvrez les fenêtres.
•
N’allumez aucun appareil.
•
Ne touchez à aucun commutateur électrique.
•
Ne vous servez d’aucun téléphone dans votre édifice.
•
Appelez immédiatement votre compagnie de gaz en utilisant le téléphone
du voisin.
•
S’il vous est impossible de contacter votre compagnie de gaz, appelez
le service des incendies.
C. N’utilisez que votre main pour manipuler le bouton de réglage du gaz.
N’utilisez jamais d’outils. Si le bouton refuse de tourner ou de bouger,
n’essayez pas de le réparer. Communiquez immédiatement avec un
technicien de service qualifié. Toute tentative pour le forcer ou le
réparer, risquerait de provoquer un incendie ou une explosion.
D. Ne vous servez pas de cet appareil si l’un de ses éléments a été
immergé dans l’eau. Appelez immédiatement un technicien compétent
pour faire inspecter l’appareil et remplacer toute pièce du système de
réglage ou commande du gaz qui a été sous l’eau.
INSTRUCTIONS D'ALLUMAGE
1.
2.
3.
4.
ARRÊTEZ! Lisez les consignes de sécurité au verso de cette plaque.
Ouvrez le compartiment de contrôle du bas.
Tournez l’interrupteur mural à la position d’arrêt “OFF”.
Assurez-vous que la soupape d’arrêt de la canalisation principale est
ouverte.
5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans
le sens des aiguilles d’une montre
jusqu’à la position
d’arrêt “OFF”.
VANNE GAZ
MILLIVOLT
HONEYWELL
PI
T FF
LO O
ON
LO
HI
PIEZO-ELECTRIQUE
IN
OUT
TPTH
TP
HI
TH
LO W
VANNE GAZ
MILLIVOLT SIT
O FF
it
PILOT
ON
PI L
OT
PIEZO-ELECTRIQUE
Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à
moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.
6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous décelez
une odeur de gaz, ARRÊTEZ ! Retournez au point “B” des consignes
de sécurité au verso de cette plaque. Si vous ne remarquez aucune
odeur de gaz, passez à l’étape suivante.
7. Enfoncez légèrement le bouton de réglage du gaz et tournez-le en
sens inverse des aiguilles d’une montre jusqu’à la position de
veilleuse
“PILOT”.
8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.
Allumez immédiatement la veilleuse en déclenchant l’allume-gaz à
étincelle (en poussant le bouton) jusqu’à ce que la veilleuse
s’enflamme. Continuez de tenir le bouton de réglage enfoncé
pendant environ 90 secondes après l’allumage de la veilleuse.
Relâchez le bouton et il sortira
subitement. La veilleuse devrait rester
HONEYWELL
allumée. Si elle s’éteint, répétez les
MILLIVOLT PILOT
étapes 5 à 8 inclusivement.
• Si le bouton ne sort pas
automatiquement après avoir été
relâché, arrêtez immédiatement et
téléphonez à votre technicien de
service ou à votre fournisseur de gaz.
• Si la veilleuse refuse de rester allumée
après plusieurs tentatives, tournez le
bouton de réglage jusqu’à sa position
d’arrêt “OFF” et téléphonez à votre
technicien de service ou à votre
fournisseur de gaz.
SIT
MILLIVOLT PILOT
9. Tournez le bouton de réglage du gaz en
sens inverse des aiguilles d’une
montre
jusqu’à sa position
de marche “ON”.
10. Fermez le compartiment de contrôle du bas.
11. Au besoin, rebrancher l’appareil au courant électrique et remettre
l’interrupteur du brûleur principal à la position “ON” ou régler le
thermostat à la température désirée.
12. Si l’appareil ne fonctionne pas, suivre les instructions intitulées
“Pour fermer le gaz qui alimente l’appareil” et appeler un
technicien ou le fournisseur de gaz.
POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL
1. Tournez l’interrupteur mural à la position d’arrêt “OFF”. La veilleuse
restera allumée jusqu’au retour du service normal.
2. Pour une fermeture complète, tournez l’interrupteur mural à la
position d’arrêt “OFF”.
4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans
le sens des aiguilles d’une montre
jusqu’à la position
d’arrêt “OFF”. Ne forcez pas le bouton.
5. Fermez le compartiment de contrôle du bas.
3. Ouvrez le compartiment de contrôle du bas.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
17
Lighting Instructions — Electronic
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A.When lighting the appliance, follow these instructions
exactly.
B.BEFORE OPERATING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
•
•
•
•
Extinguish any open flame.
Open windows.
Do not light any appliance.
Do not touch any electrical switches.
Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone.
• If your gas supplier cannot be reached, call the fire
department.
C. Use only your hand to turn the gas control lever. Never
use tools. If the lever will not turn by hand, do not try
to repair it, call a qualified service technician. Force or
attempted repair may result in a fire or an explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been under
water.
LIGHTING INSTRUCTIONS
1.STOP! Read the safety information above on this Page.
5. Turn the OFF/ON switch to “OFF”. Do not force.
2. Turn remote wall switch to “OFF.”
6. Wait five (5) minutes to clear out any gas. If you then
smell gas, STOP! Follow “B” in the safety information
above on this Page. If you do not smell gas, go to the
next step.
3. Open lower control compartment door.
4. Verify main line shut-off valve is open.
7. Turn the OFF/ON switch to “ON”. Do not force.
Honeywell Electronic Gas Control Valve
8. Turn “ON” all electrical power to appliance (remote wall
or appliance switch).
ON / OFF Switch
IN
OFF
ON
CONTROL
9. Close lower control compartment door.
IGNITER
PSI
To shut off
1. Turn off all electrical power to the appliance (remote wall
switch).
Front View
TO TURN OFF GAS TO APPLIANCE
1. For complete shut-down, turn remote wall switch to
“OFF.”
2. Open lower control compartment door.
18
3. Turn the OFF/ON switch to “OFF”. Do not force.
4. Close the main line shut-off valve.
5. Close lower control compartment door.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTRUCTIONS D’ALLUMAGE — ELECTRONIC
POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE
AVERTISSEMENT
: SI
INSTRUCTIONS ÀÀ LA
LA LETTRE,
LETTRE, IL
ILPOURRAIT
POURRAITS’EN
S’ENSUIVRE
SUIVREUN
UNINCENDIE
INCENDIEOU
OU
AVERTISSEMENT:
SI VOUS
VOUS NE
NE SUIVEZ
SUIVEZ PAS
PAS CES
CES INSTRUCTIONS
UNE
EXPLOSION
CAUSANT
DES
DOMMAGES
MATÉRIELS,
DES
BLESSURES
CORPORELLES
OU
MÊME
DES
PERTES
DE
VIE.
UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.
A. Lorsque vous allumez l’appareil, suivez exactement ces instructions.
B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez
aucune odeur de gaz autour de l’apareil ainsi que près du sol;
certains gaz, étant plus lourds que l’air, descendent au niveau du
sol.
VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE
ODEUR DE GAZ
• Éteignez toute flamme visible.
• Ouvrez les fenêtres.
• N’allumez aucun appareil.
• Ne touchez à aucun commutateur électrique.
• Ne vous servez d’aucun téléphone dans votre édifice.
• Appelez immédiatement votre compagnie de gaz en utilisant
le téléphone du voisin.
• S’il vous est impossible de contacter votre compagnie de
gaz, appelez le service des incendies.
C. N’utilisez que votre main pour manipuler linterrupteur “ON/
OFF” de la valve à gaz. N’utilisez jamais d’outils. Si
l’interrupteur ne bouge pas manuellement, n’essayez pas de le
réparer. Communiquez immèdiatement avec un technicien de
service qualifié. Toute tentative pour forcer l’interrupteur ou le
réparer, risquerait de provoquer un incendie ou une explosion.
D. Ne vous servez pas de cet appareil si l’un de ses éléments a été
immergé dans l’eau. Appelez immédiatement un technicien
compétent pour faire inspecter l’appareil et remplacer toute
pièce du système de réglage ou commande du gaz qui a été sous
l’eau.
INSTRUCTIONS D’ALLUMAGE
2. Tournez l’interrupteur mural à la position d’arrêt “OFF”.
6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous
décelez une odeur de gaz ARRÊTEZ ! Retournez au point “B” des
consignes de sécurité au verso de cette plaque. Si vous ne
remarquez aucune odeur de gaz, passez à l’étape suivante.
3. Ouvrez la porte du compartiment de contrôle du bas.
7. Tournez la manette de réglage du gaz jusqu’à la position de marche
“ON”. Ne la forcez pas.
4. Assurez-vous que la soupape d’arrêt de la canalisation principale
est ouverte.
8. Ouvrez le courant électrique (“ON”) qui alimente l’appareil
(interrupteur mural).
5. Tournez la manette de réglage du gaz à la position d’arrêt “OFF”.
9. Fermez la porte du compartiment de contrôle du bas.
1. ARRÊTEZ ! Lisez les consignes de sécurité au verso de cette
plaque.
10. Au besoin, rebrancher l’apareil au courant électrique et
remettre l’interrupteur principal du brûleur à la position “ON”
ou régler le thermostat à la température désirée.
Interrupteur
ON/OFF
IN
OFF
ON
CONTROL
11. Si l’appareil ne se met pas en marche, suivre les instructions
intitulées “Pour fermer le gaz qui alimente l’appareil” et appeler
un technicien ou le fournisseur de gaz.
PSI
IGNITER
POUR ÉTEINDRE L’APPAREIL
1. Coupez tout le courant électrique qui alimente l’appareil (interrupteur
mural).
Vue de face
POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL
1. Pour une fermeture complète, tournez l’interrupteur mural à la
position d’arrêt “OFF”.
3. Tournez la manette de réglage du gaz à la position d’arrêt “OFF”.
Ne la forcez pas.
2. Ouvrez la porte du compartiment de contrôle du bas.
4. Fermez la soupape d’arrêt de la canalisation principale.
5. Fermez la porte du compartiment de contrôle du bas.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
19
MAINTENANCE SCHEDULE
Annually (Before the onset of the Burning Season)
MAINTENANCE TASK
ACCOMPLISHING PERSON
PROCEDURE
Inspecting/Cleaning Burner, Logs
and Controls
Qualified Service Technician
Inspect valve and ensure it is properly operating. Check piping
for leaks. Vacuum the control compartment, fireplace logs and
burner area.
Check Flame Patterns and Flame
Height
Qualified Service Technician
Refer to Figure 9 on Page 9 and verify the flame pattern and
height displayed by the appliance conforms to the picture. Flames
must not impinge on the logs. Ensure flames are steady (not
lifting or floating).
Inspecting/Cleaning Pilot and Burner
Qualified Service Technician
Refer to Figure 11 (SIT Millivolt), Figure 12 (Honeywell Millivolt)
or Figure 13 (Electronic) on Page 10. Remove any surface
build-up on pilot and burner assembly. Wipe the pilot nozzles,
igniter/flame rod and hood. Ensure the pilot flame engulfs the
flame sensor as shown.
Checking Vent System
Qualified Service Technician
Inspect the vent system at the top and at the base (within the
firebox) for signs of blockage or obstruction. Look for any signs
of dislocation or deterioration of the vent components. Note:
Excessive condensation can cause corrosion of caps, pipe &
fittings (excessive condensation can be caused by long lateral
runs, too many elbows and/or exterior portions of the system
being exposed to cold weather). Also inspect wall straps or
plumbers's tape to ensure it is secure and in place.
Appliance Checkout
Qualified Service Technician
Perform the appropriate appliance checkout procedure detailed
in this manual.
Homeowner/Qualified Service
Technician
Remove old ember materials (rockwool) and vacuum the ember
placement area. Place new embers as described and shown in
Figures 8 & 9.
ACCOMPLISHING PERSON
PROCEDURE
Cleaning Firebox Interior
Homeowner
Carefully remove logs, rockwool and volcanic stone. Vacuum
out interior of the firebox. Clean firebox walls and log grate.
Replace logs, rockwool, and volcanic stone as detailed in this
manual.
Check Flame Patterns and Flame
Height
Homeowner
Refer to Figure 9 on Page 9 and verify the flame pattern and
height displayed by the appliance conforms to the picture. Flames
must not impinge on the logs.
Checking Vent System
Homeowner
Inspect the vent system at the top and at the base (within the
firebox) for signs of blockage or obstruction. Look for any signs
of dislocation of the vent components.
Cleaning Front Glass Enclosure Panel
Homeowner
Clean as necessary following the directions provided in this
manual. Do not touch or attempt to clean glass
while hot.
Replacing Rockwool Ember Materials
Periodically (After the Burning Season)
MAINTENANCE TASK
20
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
TROUBLESHOOTING
Note: Before troubleshooting the gas control system, Ensure external gas shut off valve, located at gas supply inlet, (and wall switch, iff applicable),
is in the “ON” position.
Important: Valve system troubleshooting should only be accomplished by a qualified service technician.
TROUBLESHOOTING GUIDE - Millivolt GAS CONTROL SYSTEM
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
1. Spark igniter will not light pilot after
repeated triggering of igniter button.
A. Defective igniter
(no spark at electrode).
Check for spark at electrode and pilot; if no spark and
electrode wire is properly connected, replace igniter.
B. Defective or misaligned electrode at pilot
(spark at electrode).
Using a match, light pilot. If pilot lights, turn off pilot
and trigger the igniter button again. If pilot lights, an
improper gas mixture caused the bad lighting and a
longer purge period is recommended. If pilot will not
light – check gap at electrode and pilot – should be 1/8"
to have a strong spark. If gap measures 1/8", replace
pilot (see Figures11 or 12 on Page 10).
C. Gas supply pressure errant.
Check inlet gas pressure. It should be within the limits
as marked on the rating plate.
D. Pilot orifice plugged.
Clean or replace pilot orifice.
A. Defective pilot generator
(thermocouple).
Check pilot flame, it must impinge on thermocouple
(see Figures11 or 12 on Page 10). Clean and/or
adjust pilot for maximum flame impingement on
thermocouple. Ensure that the connection between
the valve and thermocouple are tight and secure.
WARNING: if the pilot will not light
after 1 minute of attempting, wait
for at least 5 minutes for gas to
clear before attempting again.
2. Pilot will not stay lit after
carefully following the lighting
instructions.
3. Pilot burning, no gas to burner, Valve A. Wall switch or wires defective.
knob “ON,” and the (standard) burner
OFF/ON switch is “ON." Read important note below.
Check wall switch and wires for proper connections.
Jumper wire across terminals at wall switch, if burner
comes on, replace defective wall switch. If okay, jumper
wires across wall switch wires at valve, if burner comes
on, wires are faulty or connections are bad.
IMPORTANT NOTE: If an optional
*remote switch is used for burner
operation, if the standard burner
OFF/ON switch is still installed on
appliance it must be in the "OFF"
position.
B. Thermopile may not be generating sufficient millivolts.
Check thermopile with millivolt meter. Take reading
at thermopile terminals of gas valve. Should read
325 millivolts minimum with optional wall switch
“OFF.” Replace faulty thermopile if reading is below
specified minimum.
C. Plugged burner orifice.
Check burner orifice for blockage and remove.
*Optional remote switch kits - wall
switch, wall thermostat or remote
control.
D. OFF/ON Switch & *Remote Switch are in
the "ON" position resulting in excessive
resistance.
When turning on the burner using a *remote switch,
ensure that the standard OFF/ON switch is in the "OFF"
position. If both switches are in the ON position, it
may result in excessive resistance (& millivolt drainage) and the burner may not come on.
A. Pilot flame may be too low or blowing (high)
causing the pilot/valve safety to drop out.
Clean and/or adjust pilot flame for maximum flame
impingement on thermocouple (see Figures11 or
12 on Page 10).
4. Frequent pilot/burner outage problem.
TROUBLESHOOTING GUIDE - ELECTRONIC IGNITION SYSTEM
SYMPTOM
1. Burner will not light.
POSSIBLE CAUSES
CORRECTIVE ACTION
A. Faulty Valve System.
See Below.
B. “OFF/ON” or wall switch defective.
Disconnect the two black wires from the wire nuts.
Test switch(s) for continuity with a multimeter. If
continuity is not indicated, switch(s) is defective and
must be replaced.
Note: Before replacing “OFF/ON” switch, Ensure to
check wiring for loose connections or broken wires
and repair as needed.
2. Burners come “ON,” then turns “OFF.”
A. Burner orifice plugged.
Check main burner orifice(s) for blockage. Clean
or replace.
B. Obstructed vent system.
Check vent system for obstructions.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
21
TROUBLESHOOTING PROCEDURE - ELECTRONIC IGNITION SYSTEM
START
CHECK
• Turn Off Gas Supply.
• Ensure Valve Switch Is In ON Position.
• Disconnect Control Harness.
• Set Thermostat To Call For Heat.
• Check for proper voltage at control harness
(see insert A). Voltage NO
2 should be 24V between
thermostat or pressure
switch and 24V common
and 24V hot.
•
•
•
•
•
Line voltage power
Low voltage transformer
Limit controller
Thermostat
Wiring
YES
Insert A
End View of Control Harness Connector
24 Volt Hot
24 Volt
Common
• Plug control harness into
valve. Wait for internal check
delay.
• Igniter warms up and glows NO
red.
• With pilot burner cable connected, measure voltage at NO
valve HSI element output. 24V
2
nominal. (See insert B)
1
• Replace valve.
YES
1
24 Volt
Switched
YES
• Replace igniter/flame rod
assembly.
YES
Check For Damaged or Missing
Terminals in Connector
• Turn on gas supply.
• Pilot burner lights.
NO
Insert B
• Check that pilot gas is flowing. Wait
to ensure pilot gas tubing is purged. NO
Recycle call for heat if necessary.
• Replace valve.
YES
• Measure voltage between 24V hot and
24V common leads to valve control.
Must measure at least 19.5 VAC with
igniter powered (see insert A). To NO
identify proper lead, this check must
be done with the valve control connected and igniter powered.
Igniter Terminals
YES
• Check transformer and
line volt supply.
YES
• Replace Pilot Assembly.
• Main valve opens and main NO
burner lights.
YES
YES
• System Is okay.
1
22
Igniter will cycle off and
back on once during the 90
second ignition trial. All
voltage measurements must
be taken while the igniter is
powered.
2
• Check that pilot flame makes good
contact with pilot burner flame rod.
• Check for good electrical connection
through the pilot tubing.
• If both of the above are good, replace
igniter/flame rod assembly.
When measuring voltage
at connections, use care
to ensure terminals are
not damaged.
• Cycle thermostat off and back on.
NO
• Main burner lights.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
• Replace valve.
REPLACEMENT PARTS LIST
Natural
No.
DESCRIPTION
Propane
Part No.
Qty.
Part No.
Qty.
–
–
–
–
Gas Fireplace Assembly
1.
Hood
H3633
1
H3633
1
2.
Louver, (Upper)
H3635
1
H3635
1
3.
Louver, (Lower)
H3637
1
H3637
1
4.
Enclosure, Glass Front (Complete)
H3649
1
H3649
1
5.
Nameplate (Brand)
56L93
1
56L93
1
6.
L a t ch
69L21
2
69L21
2
7.
Catch, Door, Magnetic
69L31
1
69L31
1
8.
Log Set (Complete)
67L39
1
67L39
1
9.
Burner Assembly
74L82
1
74L82
1
10.
Burner, Bracket
H4892
2
H4892
2
11.
Burner, Bracket
H4890
1
H4890
1
12.
Ember Screen
H6908
1
H6908
1
13.
Orifice, Main Burner
37L66
1
99K78
1
14.
Bag of Rockwool
88L53
1
88L53
1
15.
Flex Gas Line (Optional)
93L32
1
93L32
1
GAS CONTROLS — SIT MILLIVOLT
Natural
No.
DESCRIPTION
20.
Gas Valve - SIT
2 1.
Piezo Igniter
2 2.
Propane
Part No.
43K07
Qty.
Part No.
88J53
Qty.
1
Pilot Assembly
10K86
69L17
1
1
10K86
69L18
23 .
Pilot Generator
60J79
1
60J79
24.
Thermocouple
1
1
1
74L57
74L56
1
Pilot Tube
74L57
74L56
25.
26.
27.
Electrode And Cable
Pilot Shield
74L58
H3737
1
1
74L58
H3737
1
1
1
1
1
1
GAS CONTROLS — HONEYWELL MILLIVOLT
No .
DESCRIPTION
30.
Gas Valve
31.
Pilot Assembly
32.
Natural
Propane
Part No.
82L86
Qty.
1
Part No.
82L87
Qty.
1
67L70
60J79
1
1
67L70
60J79
1
Pilot Generator
33.
Thermocouple
67L67
1
67L67
1
34.
Pilot Tube
1
Electrode And Cable
1
67L68
67L87
1
35.
67L68
67L87
3 6.
37.
Piezo Igniter
Pilot Shield
24M89
H3737
1
1
24M89
H3737
1
1
1
1
GAS CONTROLS — ELECTRONIC
Natural
No.
DESCRIPTION
40.
41.
Propane
Part No.
Qty.
Part No.
Qty.
Gas Valve - Honeywell
62L18
Pilot Assembly
62L14
1
62L19
1
1
62L15
1
42.
Transformer
42J32
1
42J32
1
43.
44.
Ignitor Assembly (Kit)
87L54
1
87L54
1
Pilot Shield
H1586
1
H1586
1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
23
REPLACEMENT PARTS DIAGRAMS
1
8
2
10
9
13
11
14
21
20
12
6
26
40
23
27
24
30
44
15
3
25
41
22
36
5
35
43
37
42
33
34
32
4
31
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by LHP
24
P/N 725,045M REV. N/C 09/2007
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LHP
1110 West Taft Avenue • Orange, CA 92865