Product specifications | Dodge 2007 Charger Automobile User Manual

VoIP Loudspeaker Amplifier
Operations Guide
(PoE)
Part #010861
930106D
VoIP Loudspeaker Amplifier Operations Guide 930106D
Part # 010861
COPYRIGHT NOTICE:
© 2007, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part
of this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or
such products, software, firmware, and/or hardware. CyberData Corporation reserves the right to
make changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by
third parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Phone: (831) 373-2601
Technical Support Ext. 333
support@cyberdata.net
Fax: (831) 373-4193
Company and product information at www.cyberdata.net
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Revision History
Revision
Date Released
Description of Changes
A
11/06/2006
This is the first release of this manual.
B
01/16/2007
Adds Section 2.4, "Set up the MGROUPS".
C
4/13/2007
Changes the Authenticate ID and password character limit from 30 to
25 in Table 2-11.
D
7/20/2007
Adds Figure 2, "Public Address System—Multicast" .
Adds more information about MGROUPS in Section 2.4, "Set up the
MGROUPS".
Adds information about the Outbound Proxy in Table 2-7.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
i
Contents
Chapter 1 Product Overview
1
1.1 Typical System Installation ...................................................................................................................1
1.2 Product Features .....................................................................................................................................2
1.3 Supported Protocols ..............................................................................................................................3
1.4 Supported SIP Servers ...........................................................................................................................3
1.5 Product Specifications ...........................................................................................................................3
Chapter 2 Installing the VoIP Loudspeaker Amplifier
5
2.1 Parts List ..................................................................................................................................................5
2.2 Loudspeaker Amplifier Setup ..............................................................................................................6
2.2.1 Loudspeaker Amplifier Components ......................................................................................6
2.2.2 Loudspeaker Amplifier Jumpers ..............................................................................................7
2.2.3 Connect the Loudspeaker Amplifier .......................................................................................8
2.2.4 Confirm Operation ....................................................................................................................10
2.2.5 Confirm the IP Address, Test the Audio, and Check the Volume ...................................... 11
2.2.6 Adjust the Volume ....................................................................................................................12
2.3 Configure the Loudspeaker Amplifier Parameters ........................................................................13
2.3.1 Log in to the Configuration Home Page ................................................................................13
2.3.2 Configure the Network Parameters ......................................................................................16
2.3.3 Set up the Loudspeaker Amplifier .........................................................................................18
2.3.4 Configure the SIP Parameters .................................................................................................19
2.4 Set up the MGROUPS ..........................................................................................................................22
2.5 Upgrade the Firmware and Reboot the Loudspeaker Amplifier ..................................................24
2.5.1 Reboot the Loudspeaker Amplifier .......................................................................................26
2.6 Restore the Factory Default Settings .................................................................................................28
Appendix A Mounting the Enclosure
29
A.0 Mount the Enclosure .........................................................................................................................29
Appendix B Setting up a TFTP Server
31
B.0 Set up a TFTP Server ...........................................................................................................................31
B.0.1 In a LINUX Environment ........................................................................................................31
B.0.2 In a Windows Environment ...................................................................................................31
Appendix C Troubleshooting/Technical Support
33
C.1 Frequently Asked Questions (FAQ) .................................................................................................33
C.2 Documentation ....................................................................................................................................33
C.3 Contact Information ............................................................................................................................33
C.4 Warranty ...............................................................................................................................................34
Index
VoIP Loudspeaker Amplifier Operations Guide
35
930106D
CyberData Corporation
ii
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
1
1 Product Overview
The Voice-over-IP (VoIP) Loudspeaker Amplifier (PoE) uses a single cable to connect to existing
LANs to broadcast digital audio over your public address system. The small footprint and low
height makes this an ideal loudspeaker amplifier to discreetly mount almost anywhere.
1.1 Typical System Installation
Figure 1 illustrates how the VoIP Loudspeaker Amplifier (PoE) is normally installed as part of a
public address system.
Figure 1. Public Address System—SIP
Generic PoE Hub
1
2
3
VoIP Loudspeaker Amplifiers—PoE
VoIP Loudspeaker Amplifier Operations Guide
4
5
6
VoIP Phone
930106D
Server
CyberData Corporation
2
Product Overview
Product Features
Figure 2. Public Address System—Multicast
CyberData VoIP Loudspeaker Amplifier Speakers Set in MGROUPS Mode
1.2 Product Features
●
Multicast support
●
SIP (RFC 3261) compatible
●
Dual-Speed 10/100 Mbps
●
Web-based configuration
●
Web-based firmware upgradeable
●
High-efficiency speaker driver
●
PoE (Power-over-Ethernet)
●
CyberData Corporation
930106D
8W output under PoE
●
16W max. output (Non-PoE)
●
Supports 8 ohm horn speakers
●
Moisture-proof NEMA enclosure
VoIP Loudspeaker Amplifier Operations Guide
Product Overview 3
Supported Protocols
1.3 Supported Protocols
The Loudspeaker Amplifier supports:
●
SIP
●
Multicast
●
HTTP Web-based configuration
Provides an intuitive user interface for easy system configuration and verification of
loudspeaker amplifier operations.
●
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
●
TFTP Client
Facilitates Web-based firmware upgrades of the latest loudspeaker amplifier capabilities.
●
RTP
●
RTP/AVP - Audio Video Profile
●
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
Packet Time 20 ms
1.4 Supported SIP Servers
The following link contains information on how to configure the loudspeaker amplifier for the
supported SIP servers:
http://www.CyberData.net/support/voip
1.5 Product Specifications
Category
Specification
Sensitivity
96dB/1W/1M S.P. Level
Output
8 W PoE/16 W with internal power supply
Port Baud Rate
10/100 Mbps
Power Requirement
802.3af compliant
Protocol
SIP RFC 3261
Part Number
010861
Dimensions
14” x 10” x 4”
Weight
4.4 lbs.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
4
Product Overview
Product Specifications
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
5
2 Installing the VoIP Loudspeaker Amplifier
2.1 Parts List
Table 2-1 illustrates the parts for each loudspeaker amplifier and includes a kit for mounting.
Table 2-1. Parts List
Quantity
Part Name
1
Loudspeaker Amplifier Assembly
1
Installation Quick Reference Guide
1
Loudspeaker Amplifier Mounting
Accessory Kit (part #070057A)
which includes:
3 x #8 x 1-1/4” truss head screws
VoIP Loudspeaker Amplifier Operations Guide
Illustration
930106D
CyberData Corporation
6
Installing the VoIP Loudspeaker Amplifier
Loudspeaker Amplifier Setup
2.2 Loudspeaker Amplifier Setup
Set up and configure each loudspeaker amplifier before you mount it.
CyberData delivers each loudspeaker amplifier with the factory default values indicated in
Table 2-2:
Table 2-2. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
static
IP Address
192.168.3.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
255.255.255.0
Default Gateway
192.168.3.1
2.2.1 Loudspeaker Amplifier Components
Figure 2-1 shows the components of the loudspeaker amplifier (PoE).
Figure 2-1. Loudspeaker Amplifier Components—PoE
LEDs
Ethernet connection
RTFM switch
Volume
Speaker connection
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 7
Loudspeaker Amplifier Setup
2.2.2 Loudspeaker Amplifier Jumpers
See Figure 2-2 to identify the jumper and component locations.
Figure 2-2. Jumper Locations
JP9
JP8
JP7
See Table 2-3 and Table 2-4 for the jumper settings.
Table 2-3. Jumper Settings—Low Power—802.3af Compliant (Default)
Jumper
Setting
JP7
OFF -> Low Power (21V)
JP8
OFF -> Low Power (21V)
JP9
Position B -> Low Power
Table 2-4. Jumper Settings—High Power—Non-PoE Compliant
Jumper
Setting
JP7
ON -> High Power (21V)
JP8
ON -> High Power (21V)
JP9
Position A -> High Power
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
8
Installing the VoIP Loudspeaker Amplifier
Loudspeaker Amplifier Setup
2.2.3 Connect the Loudspeaker Amplifier
Figure 2-3 illustrates how to connect the VoIP Loudspeaker Amplifier (PoE).
Figure 2-3. Connect a Loudspeaker
+
-
Ethernet Hub
Optional 2 Speaker Configuration
8 Ohms
CyberData Corporation
930106D
Standard 1 Speaker Configuration
8 Ohms
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 9
Loudspeaker Amplifier Setup
See Table 2-5 for details about connecting the loudspeaker amplifier.
Table 2-5. Loudspeaker Amplifier Connections
Connection
Connection Details
Location
Loudspeaker
●
Use two binding posts for up to 0.083 inch
diameter loudspeaker wire.
VoIP paging amplifier
Ethernet
●
Use a RJ 45 cable.
VoIP paging amplifier
●
For a phase connection, use a press-down
connector for 14 AWG solid copper wire.
AC panel
●
For a neutral connection, use a press-down
connector for 14 AWG solid copper wire.
●
For an earth/ground connection, use a screwdown connector for 14 AWG solid copper wire.
AC
a
a.Consult a licensed electrician for local electrical code requirements.
2.2.3.1 Loudspeaker Type
The CyberData VoIP Loudspeaker Amplifier supports an 8 Ohm Bogen or equivalent unamplified
loudspeaker. See Figure 2-4.
Figure 2-4. Hornspeaker
2.2.3.2 Cabling/Wiring
You may connect a loudspeaker to a loudspeaker amplifier with a good quality speaker cable that is
limited to 25 feet in length.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
10
Installing the VoIP Loudspeaker Amplifier
Loudspeaker Amplifier Setup
2.2.4 Confirm Operation
After connecting the loudspeaker amplifier to the ethernet hub, use the LEDs on the loudspeaker
amplifier face to confirm that the loudspeaker amplifier is operational and linked to the network.
Figure 2-5. Loudspeaker Amplifier LEDs—Power and Link
Power LED (blue/green)
Link LED (green/yellow)
Figure 2-6. Loudspeaker Amplifier LEDs—Status and Activity
Status LED (green)
Activity LED (green)
Table 2-6. Loudspeaker Amplifier LEDs
LED
Color
Function
Power
Blue/Green
The power LED is illuminated a steady blue when the power is
on and blue/green when the amplifier is in the high power mode.
Status
Green
After supplying power to the loudspeaker amplifier:
1. The green Status LED illuminates after approximately five
seconds to indicate the start of the firmware verification and load
process.
2. After approximately 15 seconds, the Status LED begins to
blink at one second intervals to indicate the start of the firmware
boot process.
3. After approximately 35 seconds, the loudspeaker amplifier
beeps once to indicate that it is operational.
4. The Status LED will continue to blink at one second intervals
to indicate normal operation.
CyberData Corporation
Link
Green/Yellow
The Link LED is illuminated green for a 10Mb link or
yellow/green for a 100Mb link when the network link to the
loudspeaker amplifier is established.
Activity
Green
The Activity LED blinks to indicate network traffic.
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 11
Loudspeaker Amplifier Setup
2.2.5 Confirm the IP Address, Test the Audio, and Check the Volume
When the loudspeaker amplifier is operational and linked to the network, use the Reset Test
Function Management (RTFM) switch (Figure 2-7) on the loudspeaker amplifier face to announce
and confirm the loudspeaker amplifier’s IP Address, test that the audio is working, and check the
volume.
Figure 2-7. RTFM Switch
RTFM switch
To announce a loudspeaker amplifier’s current IP address:
1. Press and hold the RTFM switch until it beeps (after one second).
2. Release the switch to hear the IP address announcement, and check the loudspeaker amplifier
volume.
Caution
Equipment Caution: Pressing and holding the RTFM switch for longer than
20 seconds will restore the loudspeaker amplifier to the factory default
settings. See Section 2.6, "Restore the Factory Default Settings".
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
12
Installing the VoIP Loudspeaker Amplifier
Loudspeaker Amplifier Setup
2.2.6 Adjust the Volume
To adjust the loudspeaker amplifier volume, turn the Volume dial (Figure 2-8) on the loudspeaker
amplifier face.
Figure 2-8. Volume Control
Volume control
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 13
Configure the Loudspeaker Amplifier Parameters
2.3 Configure the Loudspeaker Amplifier Parameters
To configure the loudspeaker amplifier online, use a standard web browser.
Configure each loudspeaker amplifier and verify its operation before you mount it. When you are
ready to mount a loudspeaker amplifier enclosure, refer to Chapter A, “Mounting the Enclosure” for
instructions.
All loudspeaker amplifiers are initially configured with the default IP settings indicated in Table 2-7.
When configuring more than one loudspeaker amplifier, attach the loudspeaker amplifiers to the
network one at a time to avoid IP address conflicts.
Table 2-7. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
static
IP Address
192.168.3.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
255.255.255.0
Default Gateway
192.168.3.1
2.3.1 Log in to the Configuration Home Page
1. Open your browser to the speaker IP address.
For the initial configuration of the speaker, open your browser to the default IP address:
http://192.168.3.10
Note
Make sure that the PC is on the same IP network as the loudspeaker amplifier.
2. When prompted, use the following default Web Access Username and Web Access Password
to access the Home Page (Figure 2-9):
Web Access Username: admin
Web Access Password: admin
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
14
Installing the VoIP Loudspeaker Amplifier
Configure the Loudspeaker Amplifier Parameters
Figure 2-9. Home Page
3. On the Home Page, review the setup details and navigation buttons described in Table 2-8.
Table 2-8. Home Page Overview
Web Page Item
Description
Device Name
Shows the device name.
Running
Shows the current speaker function.
Serial #
Device serial number.
Ethernet Address
Device ethernet address.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
Link to the Speaker Setup page.
Link to the Network Setup page.
Link to the SIP Setup page.
Link to the MGROUPS Setup page.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 15
Configure the Loudspeaker Amplifier Parameters
Table 2-8. Home Page Overview
Web Page Item
Description
Link to the Upgrade Firmware web page.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
16
Installing the VoIP Loudspeaker Amplifier
Configure the Loudspeaker Amplifier Parameters
2.3.2 Configure the Network Parameters
1. Click the Network Setup button to open the Network Setup page (Figure 2-10).
Figure 2-10. Network Setup Page
2. On the Network Setup page, enter values for the parameters indicated in Table 2-9.
Table 2-9. Network Setup Parameters
Web Page Item
Description
IP Addressing*
Select either DHCP IP Addressing or Static IP Addressing by
marking the appropriate radio button. If you select Static, configure
the remaining parameters indicated in Table 2-9. If you select DHCP,
go to Step 3.
IP Address*
Enter the static IP address.
Subnet Mask
Enter the Subnet Mask address.
Default Gateway
Enter the Default Gateway address.
DNS Server 1*
Enter the DNS Server 1 address.
DNS Server 2*
Enter the DNS Server 2 address.
Click this button to save your configuration settings. Changing a
parameter that has an asterisk next to it will cause a system reboot
when saved.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 17
Configure the Loudspeaker Amplifier Parameters
Table 2-9. Network Setup Parameters
Web Page Item
Description
Link to the Speaker Setup page.
Link to the SIP Setup page.
Link to the MGROUPS Setup page.
Link to the Upgrade Firmware page.
Link to the Home page.
3. After changing the parameters, click Save Settings. This updates the changed parameters and
reboots the speaker if appropriate.
4. Connect the speaker to the target network.
5. From a system on the same network as the speaker, open a browser with the new IP address of
the speaker.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
18
Installing the VoIP Loudspeaker Amplifier
Configure the Loudspeaker Amplifier Parameters
2.3.3 Set up the Loudspeaker Amplifier
1. Click the Speaker Setup button to open the Speaker Setup page. See Figure 2-11
Figure 2-11. Loudspeaker Amplifier Setup
2. On the Loudspeaker Amplifier Setup page, enter values for the parameters indicated in
Table 2-10.
Table 2-10. Loudspeaker Amplifier Setup Parameters
Web Page Item
Description
Device Name
Enter a descriptive name for this device (if desired).
Select Speaker Function
Select SIP or MGROUPS.
Change Web Access Username
Use this field to change the Web Access Username.
Change Web Access Password
Use this field to change the Web Access Password.
Re-enter New Password
Use this field to re-enter a new password.
Speaker Tone Before Paging
Enable/Disable the speaker tone (beep) before each page.
Speaker Tone After Initialization
Enable/Disable the speaker tone (beep) after the system
startup.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 19
Configure the Loudspeaker Amplifier Parameters
Table 2-10. Loudspeaker Amplifier Setup Parameters
Web Page Item
RTFM Announcement
Description
a
Enable/Disable the speaker tone (beep) and audio
associated with the RTFM switch.
Click on this button to save your configuration settings.
Changing a parameter that has an asterisk next to it will
cause a system reboot when saved.
Click on this button to do an audio test. Generates a voice
message for testing the speaker audio quality and volume.
Link to the Network Setup page.
Link to the SIP Setup page.
Link to the MGROUPS Setup page.
Link to the Upgrade Firmware page.
Link to the Home Page page.
a.If you select No for RTFM Announcement, you will not hear a beep or associated RTFM audio.
However, the return to default settings function remains active. If you wish to return to default
settings, hold the RTFM button at least 20 seconds, then release the button.
3. After changing the parameters, click Save Settings.
2.3.4 Configure the SIP Parameters
1. Click SIP Setup to open the SIP Setup page (Figure 2-12).
Note
For specific server configurations, go to the following URL:
http://www.CyberData.net/support/voip
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
20
Installing the VoIP Loudspeaker Amplifier
Configure the Loudspeaker Amplifier Parameters
Figure 2-12. SIP Setup Page
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 21
Configure the Loudspeaker Amplifier Parameters
2. On the SIP Setup page, enter values for the parameters indicated in Table 2-11.
Table 2-11. SIP Setup Parameters
Web Page Item
Description
SIP Server*
Enter the SIP server represented as either a numeric IP
address in dotted decimal notation or the fully qualified
host name (FQHN) up to 64 characters.
Outbound Proxy
Enter the Outbound Proxy as either a numeric IP address
in dotted decimal notation or the fully qualified host name
(FQHN) up to 64 characters.
Remote SIP Port*
Enter the Remote SIP Port number (default 5060).
Local SIP Port*
Enter the Local SIP Port number (default 5060).
SIP User ID*
Enter the SIP User ID (up to 25 alphanumeric characters).
Authenticate ID*
Enter the Authenticate ID (up to 25 alphanumeric
characters).
Authenticate Password*
Enter the Authenticate Password (up to 25 alphanumeric
characters).
SIP Registration*
Enable/Disable SIP Registration.
Unregister on Reboot*
• Select Yes to automatically unregister the paging
amplifier when it is rebooted.
• Select No to keep the paging amplifier registered when it
is rebooted.
Register Expiration*
Enter the SIP Registration lease time in minutes (default 60
minutes).
Click this button to save your configuration settings.
Changing a parameter that has an asterisk next to it will
cause a system reboot when saved.
Link to the Speaker Setup page.
Link to the MGROUPS Setup page.
Link to the Network Setup page.
Link to the Upgrade Firmware page.
Link to the Home page.
3. After changing the parameters, click Save Settings.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
22
Installing the VoIP Loudspeaker Amplifier
Set up the MGROUPS
2.4 Set up the MGROUPS
MGROUPS uses multicasting to create Public Address Paging Zones. Multicasting is based on the
concept of a group. Multicast addresses specify an arbitrary group of IP hosts that have joined the
group and want to receive traffic sent to the group. Group members send IGMP messages to their
local multicast routers, allowing the group traffic traversal from the source.
MGROUPS Setup provides the ability to join up to 10 Paging Zones. A Paging Zone can consist of
one, or many, CyberData MGROUPS-enabled speakers. There is no limit to how many speakers can
be in a given Paging Zone. Each MGROUP is defined by a multicast address and port number. Each
MGROUP is also assigned a priority, allowing simultaneously arriving pages to be serviced based
on importance. MGROUPS are compatible with IGMP through version 3.
1. Click on the MGROUPS Setup button to open the MGROUPS Setup page. See Figure 2-13.
Figure 2-13. MGROUPS Setup
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 23
Set up the MGROUPS
2. On the MGROUPS Setup page, enter values for the parameters indicated in Table 2-12.
Table 2-12. MGROUPS Setup Parameters
Web Page Item
Description
Device Name
Displays the device name.
MG-Emergency
Use MG-Emergency for the MGROUP with the highest
priority.
MG-(1-8)
Use MG-(1-8) to assign MGROUPS 1 through 8.
MG-Background
Use MG-Background for the MGROUP with the lowest
priority (background audio for example).
Multicast IP Address
Enter the multicast IP Address for this MGROUP.
Port 2000-65535
Enter the port number for this MGROUP.
Priority
Assign the priority to a MGROUP (the higher the number,
the higher the priority).
MGROUP Name
Assign a descriptive name for this MGROUP.
Beep
Check this box if you want a beep to precede a page.
Click this button to save your configuration settings.
Click this button to reboot the system.
Link to the Network Setup page.
Link to the Speaker Setup page.
Link to the SIP Setup page.
Link to the Upgrade Firmware page.
Link to the Home page.
3. After changing the parameters, click Save Settings.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
24
Installing the VoIP Loudspeaker Amplifier
Upgrade the Firmware and Reboot the Loudspeaker Amplifier
2.5 Upgrade the Firmware and Reboot the Loudspeaker
Amplifier
To upload the speaker firmware from your PC:
1. Set up a TFTP server.
If you do not already have a TFTP server running on your network, see Chapter B, “Setting up a
TFTP Server”.
2. Retrieve the latest speaker firmware from the CyberData website:
www.CyberData.net/support/voip
3. Unzip the speaker version file. This file may contain the following:
•
Kernel firmware file: xxx-image-xxx-xxx.bin
•
Application firmware file: xxx-romdisk-xxx-xxx.img
•
Release notes
4. Copy the firmware files to be upgraded to the appropriate TFTP server directory:
•
c:\tftp-root\ (for Windows)
•
/tftpboot/ (for Linux)
5. Log in to the speaker home page as instructed in Section 2.3.1, "Log in to the Configuration
Home Page".
6. Click the Upgrade Firmware button to open the Firmware Upgrade page. See Figure 2-14.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 25
Upgrade the Firmware and Reboot the Loudspeaker Amplifier
Figure 2-14. Firmware Upgrade Page
7. Enter the IP address of your TFTP server into the TFTP Server IP parameter field.
8. Enter the firmware filename of the file to be uploaded into the New Filename parameter field.
For example, kernel filename "201-image-spk-sip.bin".
9. Click Upload File.
Note
This starts the upload process. Once the speaker has uploaded the file, the Uploading
Firmware countdown page appears, indicating that the firmware is being written to flash.
The speaker will automatically reboot when the upload is complete. When the countdown
finishes, the Firmware Upgrade page will refresh. The uploaded firmware filename should
be displayed in the system configuration (indicating successful upload and reboot).
10. Repeat steps 8 and 9 if you are uploading the Kernel and Application files.
For example, Application filename "201-romdisk-spk-sip.img".
Table 2-13 shows the web page items on the Firmware Upgrade page.
Table 2-13. Firmware Upgrade Parameters
Web Page Item
Description
System Configuration
Shows the current configuration.
Bootname
Shows the current boot loader filename.
Kernel
Shows the current kernel filename for partition 1 and 2.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
26
Installing the VoIP Loudspeaker Amplifier
Upgrade the Firmware and Reboot the Loudspeaker Amplifier
Table 2-13. Firmware Upgrade Parameters
Web Page Item
Description
Application
Shows the current application filename for partition 1
and 2.
Load new firmware to Partition 1
Enter the TFTP Server IP address.
New Filename
Enter the new file name for the kernel or application
firmware file that you are uploading.
Click on this button to automatically upload the selected
firmware and reboot the system.
Link to the Speaker Setup page.
Link to the Network Setup page.
Link to go to the SIP Setup page.
Link to the MGROUPS Setup page.
Link to the Home page.
Click on this button to reboot the system.
2.5.1 Reboot the Loudspeaker Amplifier
To reboot a loudspeaker amplifier, log in to the web page as instructed in Section 2.3.1, "Log in to the
Configuration Home Page".
1. Click Upgrade Firmware to open the Firmware Upgrade page (Figure 2-15). Use the Reboot
System section on the right side of the page.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Installing the VoIP Loudspeaker Amplifier 27
Upgrade the Firmware and Reboot the Loudspeaker Amplifier
Figure 2-15. Reboot System Section
2. Click Reboot. A normal restart will occur as per the Status LED section of Table 2-6.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
28
Installing the VoIP Loudspeaker Amplifier
Restore the Factory Default Settings
2.6 Restore the Factory Default Settings
When troubleshooting configuration problems, it is sometimes convenient to restore the device to a
known state.
Each loudspeaker amplifier is delivered with factory set default values for the parameters indicated
in Table 2-14. Use the RTFM switch on the loudspeaker amplifier face to restore these parameters to
the factory default settings.
When you use the RTFM switch, the factory default settings are restored for only the parameters
indicated in Table 2-14. The other parameters in the current loudspeaker amplifier configuration
will remain unchanged.
Table 2-14. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
static
IP Address
192.168.3.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
255.255.255.0
Default Gateway
192.168.3.1
To restore these parameters to the factory default settings:
1. Press and hold the RTFM switch for 20 seconds.
2. The loudspeaker amplifier will beep after one second. Continue to hold the switch until the
loudspeaker amplifier beeps again after 20 seconds.
3. Release the switch. The following occurs:
•
A voice message announces that the factory default settings are being restored.
•
Once the settings are restored, a voice message announces the restored default IP address:
192.168.3.10
CyberData Corporation
•
A voice message announces that the loudspeaker amplifier is rebooting.
•
The loudspeaker amplifier reboots.
930106D
VoIP Loudspeaker Amplifier Operations Guide
29
Appendix A: Mounting the Enclosure
A.0 Mount the Enclosure
Before you mount the enclosure, make sure that you have received all of the parts for each
enclosure. Refer to Table A-15.
Table A-15. Wall Mounting Components (Part of the Accessory Kit)
Quantity
Part Name
3
#8 Sheet Metal Screws
Note
Illustration
The loudspeaker amplifier was designed for indoor use. Mounting it on the external part of
a building will require additional hardware for weatherproofing, cabling access, and
lightning suppression. Consult a certified electrician for details.
See Figure A-1 to mount the enclosure.
Note
For mounting, use the three #8 SHEET METAL SCREWS to secure the enclosure.
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
30
Mount the Enclosure
Figure A-1. Loudspeaker Amplifier Enclosure Assembly
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
31
Appendix B: Setting up a TFTP Server
B.0 Set up a TFTP Server
Upgrading the VoIP Loudspeaker Amplifier firmware requires a TFTP server on which you access
the Web interface where you can upload the firmware files.
B.0.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.0.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
http://www.CyberData.net/support/voip
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
4. You can find several options online for setting up a Solarwinds server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
http://www.CyberData.net/support/voip
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
32
Set up a TFTP Server
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
33
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
Go to the following URL to see CyberData’s list of frequently asked questions:
http://www.CyberData.net/support/voip
C.2 Documentation
The documentation for this product is released in an English language version only. You can
download PDF copies of CyberData product documentation at:
www.CyberData.net—>Support—>Drivers, Utilities & Manuals—>VoIP Products
C.3 Contact Information
Contact
CyberData Corporation
2555 Garden Road
Monterey, CA 93940
USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales (831) 373-2601 Extension 334
Technical
Support
Phone: 831-373-2601 Extension 333
Email: support@CyberData.net
Returned
Materials
Authorization
To return the product, contact the CyberData Returned Materials Authorization (RMA) department
at:
Phone: 831-373-2601, Extension 136
Email: RMA@CyberData.net
When returning a product to CyberData, an approved CyberData RMA number must be printed on
the outside of the original shipping package. No product will be accepted for return without an
approved RMA number. Send the product, in its original package, to the following address:
CyberData Corporation
2555 Garden Road
Monterey, CA 93940
Attention: RMA "your RMA number"
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
34
Warranty
C.4 Warranty
CyberData warrants its product against defects in material or workmanship for a period of two
years from the date of purchase. Should the product fail within the warranty period, CyberData will
repair or replace the product free of charge. This warranty includes all parts and labor.
If the product is out-of-warranty and fails, a flat rate repair charge of one half the product purchase
price will be assessed. Repair costs for products that are in warranty, but damaged by improper
modifications or abuse, will be charged at the out-of-warranty rate. Products returned to CyberData,
both in and out-of-warranty, are shipped to CyberData at the expense of the customer. Charges for
shipping repaired products back to the customer will be paid by CyberData.
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
35
Index
DHCP Client 3
DHCP IP addressing 16
dimensions 3
DNS server 16
Symbols
#8 sheet metal screws 29
Numerics
E
3 x #8 x 1-1/4” truss head screws 5
enclosure, mounting 29
expiration time for SIP server lease 21
A
F
accessory kit 5
activity LED 10
address, configuration login 13
announcing a loudspeaker amplifier’s IP address 11
asterisk 16, 19
audio encodings 3
factory default settings 28
firmware upgrades 31
H
home page 13
http web-based configuration 3
C
changing
the web access password 18
configurable parameters 14, 16, 18, 21, 25
configuration
default IP settings 13
network 16
SIP 19
using Web interface 13
configuration home page 13
CyberData contact information, corporate, sales, tech
support, service 33
illustration of enclosure mounting process 29
installation, typical loudspeaker amplifier system 1
IP address 6, 13, 16, 28
IP addressing 16
J
jumpers, settings 7
D
default
gateway 6, 13, 28
IP address 6, 13, 28
loudspeaker amplifier settings 35
subnet mask 6, 13, 28
username and password 6, 13, 28
web login username and password 13
default gateway 6, 13, 16, 28
default IP settings 13
default login address 13
default loudspeaker amplifier settings 28
VoIP Loudspeaker Amplifier Operations Guide
I
L
lease, SIP server expiration time 21
LEDs 10
link LED 10
Linux, setting up a TFTP server on 31
local SIP port 21
log in address 13
loudspeaker amplifer configuration page
configurable parameters 18
930106D
CyberData Corporation
36
loudspeaker amplifer setup 18
loudspeaker amplifier configuration
default IP settings 13
loudspeaker amplifier configuration page
configurable parameters 14, 16, 21, 25
loudspeaker amplifier operations, verifying 18
loudspeaker, cabling/wiring 9
loudspeaker, type 9
product
configuring 13
mounting 29
parts list 5
product features 2
product overview
product features 2
product specifications 3
supported protocols 3
supported SIP servers 3
typical system installation 1
product specifications 3
protocols supported 3
M
MGROUP
MG-(1-8) 23
MG-Background 23
MG-Emergency 23
MGROUP Name 23
Multicast IP Address 23
mounting an enclosure 29
R
reboot 26, 28
registration and expiration, SIP server lease 21
remote SIP port 21
reset test function management switch 11
resetting the IP address to the default 29, 33
restoring factory default settings 28, 35
RMA returned materials authorization 33
RTFM switch 11, 28
RTP/AVP 3
N
network configuration of loudspeaker amplifier 16
network link activity, verifying 10
Network Setup 16
S
O
sensitivity 3
server address, SIP 21
setting up a TFTP server 31
settings, default 28
SIP (session initiation protocol) 3
SIP Configuration 19
SIP configuration
SIP Server 21
SIP registration 21
SIP server 21
SIP servers supported 3
static IP addressing 16
status LED 10
subnet mask 6, 13, 16, 28
supported protocols 3
outbound proxy 21
output 3
P
packet time 3
part number 3
parts
#8 sheet metal screws 29
parts list 5
password
changing for web configuration access 18
for SIP server login 21
login 13
restoring the default 6, 13, 28
port
local SIP 21
remote SIP 21
port baud rate 3
power LED 10
power requirement 3
power, connecting to loudspeaker amplifier 8
CyberData Corporation
T
technical support, contact information 33
TFTP server 3, 31
truss head screws 5
930106D
VoIP Loudspeaker Amplifier Operations Guide
37
U
unregister, from SIP server 21
user ID
for SIP server login 21
user ID, SIP 21
username
changing for web configuration access 18
default for web configuration access 13
restoring the default 6, 13, 28
V
verifying
loudspeaker amplifier operations 18
network link and activity 10
power on to loudspeaker amplifer 10
W
warranty 34
web access password 6, 13, 28
web access username 6, 13, 28
web configuration log in address 13
web-based loudspeaker amplifier configuration 13
weight 3
Windows, setting up a TFTP server on 31
VoIP Loudspeaker Amplifier Operations Guide
930106D
CyberData Corporation
38
CyberData Corporation
930106D
VoIP Loudspeaker Amplifier Operations Guide
Download PDF

advertising