Dodge 2007 Ram 2500 Automobile User Manual

AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 1
AP_LX-M150A(ENG)_112S
MICRO HI-FI SYSTEM
OWNER’S MANUAL
MODEL: LX-M150
(LX-M150A/D/X , LXS-M150)
Please read this manual carefully before operating your set.
Retain it for future reference.
Designs and specifications are subject to change without
notice for improvement.
CD-R/RW
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 2
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR
BACK) NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Explanation Graphical Symbols:
The lightning flash with arrowhead
symbol, within an equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance(servicing)
instructions in the literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
To avoid electrical shock, do not open the cabinet, Refer servicing to qualified personnel only.
The apparatus shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed
on the apparatus.
Warning:Do not install this equipment in a confined space such a book case or similar unit.
2
CAUTION:INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VARNING:OSYNLIG LASERSTRÅLNING
NÄR DENNA DEL ÄR ÖPPNAD STRÅLEN
ÄR FARLIG.
Attention:Quand l'appareil est ouvert, ne
pas s'exposer aux radiations invisibles du
faisceau laser.
This label is located on the interior.
This Compact Disc player is classified as a CLASS
1 LASER product.
The CLASS 1 LASER PRODUCT label is
located on the exterior.
CAUTION
Use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
Laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
CAUTION concerning the Power Cord
Most appliances recommend they be placed
upon a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of
this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock or
fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use
of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer.
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the
appliance.
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 3
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . .4
About the Symbols for instructions .
Notes on Tapes . . . . . . . . . . . . . . .
Notes on Discs . . . . . . . . . . . . . . .
Handling discs . . . . . . . . . . . . . .
Storing discs . . . . . . . . . . . . . . . .
Cleaning discs . . . . . . . . . . . . . .
Adjusting the voltage - OPTIONAL .
Front / Rear Panel . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . .
Remote Control battery installation
Remote Control Operation Range
Display Window . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.4
.4
.4
.4
.4
.4
.4
.5
.6
.6
.6
.7
2 Installation . . . . . . . . . . . . . . . . . . . . . . . .8
Speaker System Connection . . . . . . . .
Antenna (Aerial) Connections . . . . . . .
Auxiliary Function . . . . . . . . . . . . . . .
Audio Adjustment . . . . . . . . . . . . . . . .
Volume Adjustment . . . . . . . . . . . . .
XDSS (Extreme Dynamic Sound System)
MUTE . . . . . . . . . . . . . . . . . . . . . . .
Sound Quality Adjustment . . . . . . . .
.
.
.
.
.
.
.
.
.8
.8
.9
.9
.9
.9
.9
.9
Recording . . . . . . . . . . . . . . . . . . . . . .14
Basic Setting . . . . . . . . . . . . . . . . . .14
Recording from Radio,CD or Auxiliary
source . . . . . . . . . . . . . . . . . . . . . . .14
CD to Tape Synchronized Recording .14
CD Playback . . . . . . . . . . . . . . . . . .15-16
Basic Playback . . . . . . . . . . . . . . . . .15
To Pause Play Back . . . . . . . . . . . . . .15
To Stop Play . . . . . . . . . . . . . . . . . . .15
To Skipping the Track . . . . . . . . . . . . .15
To Play Fast Rewind or Fast Forward. 15
To Repeat Play . . . . . . . . . . . . . . . . .15
To check the MP3 file information . . .15
To Program Play . . . . . . . . . . . . . . . .16
About MP3 . . . . . . . . . . . . . . . . . . . .16
4 Maintenance and Service . . . . . . . . . . . .17
Troubleshooting . . . . . . . . . . . . . . . . . .17
5 Reference . . . . . . . . . . . . . . . . . . . . . . . .18
Specifications . . . . . . . . . . . . . . . . . . . .18
3 Operation . . . . . . . . . . . . . . . . . . . . . .10-13
Setting the Clock . . . . . . . . . . . . . . . . . .10
Sleep Function
. . . . . . . . . . . . . . . . .10
Timer Function . . . . . . . . . . . . . . . . . . .11
RDS Function - OPTIONAL . . . . . . . . . .12
About RDS . . . . . . . . . . . . . . . . . . . .12
RDS Tuning . . . . . . . . . . . . . . . . . . .12
RDS Display Options . . . . . . . . . . . .12
Programme Search (PTY) . . . . . . . . .12
Presetting the Radio Stations . . . . . . . .13
Listening to the Radio . . . . . . . . . . . . .13
Tape Playback . . . . . . . . . . . . . . . . . . .14
Basic Playback . . . . . . . . . . . . . . . . .14
To Stop Play . . . . . . . . . . . . . . . . . . .14
To Pause Play . . . . . . . . . . . . . . . . . .14
To Play Rewind or Fast Forward . . . .14
Auto Stop Deck . . . . . . . . . . . . . . . . .14
3
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 4
1. Introduction
About the symbols for instructions
Indicates hazards likely to cause harm to the
unit itself or other material damage.
Indicates special operating features of this
unit.
Notes on Discs
Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on
the disc.
Notes on Tapes
Tapes
Preventing overwriting a recording
Removing the tab(s) of the cassette (with a small
screwdriver) will prevent accidental erasure.
Side A
Tab for side A
Storing discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Cleaning discs
Tab for side B
To record again, cover the hole of the tab with
adhesive tape.
Adhesive tape.
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the
disc from the center out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
Adjusting the voltage - OPTIONAL
If your unit is equipped with a voltage selector at
the back side, be sure to set it to your local
power supplied before connecting the AC power
cord.
4
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 5
1
2
3
4
5
6
7
17
16
Introduction
Front / Rear Panel
22
15
14
OPTIONAL
AM
13
12
FM GND
11
21
8
18
L
R
10
20
19
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD DOORZ
POWER (1STANDBY/ON) button
Remote Control Sensor
POWER indicator
VOLUME CONTROL KNOB
HEADPHONE SOCKET ( PHONE):
3.5mm
• CLOCK button
• TIMER button
• REPEAT button
• PROGRAM/MEMORY button
• STOP/CLEAR button
CASSETTE Holder
• RECORD (z) button - TAPE
• PLAY (B) button - TAPE
• REWIND (m) button - TAPE
• FAST FORWARD (M) button - TAPE
• STOP/EJECT(x/Z) button - TAPE
• PAUSE(X) button -TAPE
10. TAPE button DOOR
11. • CD PLAY/PAUSE (CDB/X) button
• PRESET (+/-) buttons
12. • CD SKIP/SEARCH (.m/M>)
buttons
• TUNING (+/-) buttons -TUNER
13. • FUNCTION SELECT (FUNCTION) button
(TUNER/ CD/ TAPE /AUX)
• TUNER/BAND button
• RDS (OPTIONAL)/SET button
14.
15.
16.
17.
18.
19.
20.
21.
22.
• MODE/RIF button
EQUALIZER PATTERN (EQ) button
DISPLAY
XDSS button
CD OPEN/CLOSE(Z) (OPEN/CLOSE) button
VOLTAGE SELECT SWITCH : OPTIONAL
POWER CORD
SPEAKER TERMINAL
AUXILIARY INPUT SOCKET (AUX)
ANTENNA TERMINAL
5
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 6
Remote control
11
1
1.
10
2
POWER button
2.
PRESET (
3.
CD FUNCTION buttons
• CD PLAY/ PAUSE (B/[]) buttons
• CD STOP(x) button
• CD SKIP/SEARCH (.m/M>)
buttons
• REPEAT button
4.
• EQUALIZER PATTERN (EQ PATT.) button
9
8
3
7
/
) buttons
• XDSS button
5.
NUMBER buttons
6.
MP3 file information display (MP3 Info)
4
button
5
6
7.
PROGRAM button
8.
SLEEP button
9.
VOLUME CONTROL (
/
) buttons
10. MUTE button
11. • TUNER/BAND button
• AUX button
Remote control battery installation
Remote Control Operation Range
Detach the battery cover on
the rear of the remote control, and insert two R03 (size
AAA) batteries with
and
aligned corectly.
,
Caution: Do not mix old and new batteries.
Never mix different types of batteries (standard,
alkaline, etc.).
6
Point the remote control at the remote sensor
and press the buttons.
• Distance: About 23 ft (7 m) from the front of the
remote sensor.
• Angle: About 30° in each direction of the front of
the remote sensor.
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 7
Introduction
Display Window
13
1
12
2
3
4
5
6
7
11
10
9
8
1.
PLAY/ PAUSE indicator
8.
MEMO. indicator
2.
FUNCTION indicators
9.
TIMER indicator
3.
MP3 indicator
10. SLEEP indicator
4.
CD REPEAT indicator
11. MUTE indicator
5.
• PROGRAM indicator
12. XDSS indicator
• RECORD/ RECORD PAUSE indicator
13. • FM STEREO indicator
6.
CD SYNCHRO RECORDING indicator
7.
RDS indicator : OPTIONAL
• FM STEREO RECEIVING indicator
7
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 8
2. Installation
Speaker System Connection
Connect the speaker cords to the speaker terminals.
red
L
black
R
red Left speaker
Right speaker
otes
• Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –.
If the cords are reversed, the sound will be distorted and will lack base.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid
excessive output on the speakers.
• Do not disassemble the front cover of supplied speaker.
Antenna (Aerial) Connections
Connect the supplied FM/AM antennas for listening to the radio.
(OPTIONAL)
FM external
antenna (aerial)
(not supplied)
FM indoor antenna (aerial)
AM loop antenna (aerial)
(Supplied)
AM (MW) loop
antenna (aerial)
(Supplied)
FM external
antenna (aerial)
(not supplied)
AM
FM 75
Position it for
the best reception
For AM (MW) reception, connect
the loop antenna (aerial) to the
terminal marked AM
300 ohms
coaxial
cable
AM
FM
FM wire antenna
(supplied)
otes
• To prevent noise pickup, keep the AM loop antenna away from the unit and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
8
3/2/06
9:54 PM
Page 9
Auxiliary Function
Sound Quality Adjustment
1. Connect an auxiliary device i.e. TV or
• To activate stereo sound
You can choose between 4 fixed sound
impressions.
Select a desired sound mode by using
the EQ button.
FLAT : linear frequency response
ROCK : more bass, more treble
POP
: less bass, less treble
CLASSIC: for orchestral music
VCR, via the rear mounted AUX phone
sockets.
2. Press AUX.
ote
You can also record from the auxiliary input
source, see Recording Section.
Audio Adjustment
Volume Adjustment
• Turn VOLUME CONTROL KNOB clockwise to
increase the sound level, or counterclockwise
to decrease it on the front panel.
Installation
AP_LX-M150A(ENG)
• Headphone Socket
Connect a stereo headphone plug ( 3.5mm)
into the headphone jack.
The speakers are automatically disconnected
when you plug in the headphone.(not supplied)
• Press VOLUME CONTROL (
) to increase the
sound level, or press the VOLUME CONTROL
(
/) to decrease it on the remote control.
XDSS (Extreme Dynamic Sound System)
Press XDSS to reinforce treble, bass and the
surround effect. The “XDSS ON” or “XDSS OFF”
indicator lights. To cancel, press XDSS again.
MUTE
Press MUTE to mute your unit.
You can mute your unit in order, for example, to
answer the telephone, “MUTE” indicator flashes
in the display window.
9
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 10
3.Operation
Setting the Clock
Sleep Function
1. Press CLOCK.
When the sleep timer is used, the power is automatically turned off after the specified time has
elapsed.
(If the clock requires setting, press and hold
CLOCK for more than 2 seconds.)
- The hours begin to flash.
2. Select a 12 hour cycle or 24 hour cycle by
pressing TUNING (+/ -) on the front panel.
(12HR)
or
(24HR)
3. Press SET to confirm the selected hour cycle.
4. Use TUNING (+/-) buttons to set the
correct hours on the front panel.
5. Press SET.
1. To specify the time delay before the
power is turned off, press SLEEP.
In the display window you can see
for about 5 seconds.
This means that the system turns off
automatically after 90 minutes.
Each time the button is pressed the time
interval before it turns off is reduced by
10 minutes. i.e. 80...70... etc.
Select the desired time to turn off.
2. To check the remaining time until the
power is turned off.
While the sleep function is active press
SLEEP briefly. The time remaining until it
turns off is displayed for about 5 seconds.
6. Use TUNING (+/-) buttons to set the
correct minutes on the front panel.
7. Press SET and the correct time is shown on
the display.
8. Press CLOCK at any time to display the time
for about 3 seconds.
ote
The unit can also set the clock function in power
off state.
10
ote
If you press SLEEP while the sleep time is displayed, the SLEEP time is reset.
To cancel the sleep timer mode
If you wish to stop the function, press the SLEEP
button repeatedly until “SLEEP 10” appears, and
then press SLEEP once again while “SLEEP 10”
is displayed.
3/2/06
9:54 PM
Page 11
Timer Function
10. Press SET to confirm the hour to switch off.
With the TIMER function you can have the radio
reception and CD play turned on and off at the
time desired.
11. Set the minute to switch off by pressing
1. Press CLOCK to check the current time.
13. Adjust the volume level by pressing
For your reference
If you don’t set clock, timer function doesn’t work.
2. Press TIMER to enter the time setting mode.
TUNER-CD flashes in the display window in
turn.
For your reference
If you want to correct the previous memorized
TIMER setting, press and hold the TIMER button
more than 2 seconds.
- The previous memorized timer on time and
“TIMER” indicators appear in the display.
3. Press SET when the desired function is flashing.
4.1.When you select the TUNER function,Select
the previous memorized preset number with
PRESET (+/-) on the front panel and press
SET.
- “ON TIME” indicator appears for about 0.5
seconds in the display window and then disappears.
TUNING (+/-) buttons on the front panel.
12. Press SET.
TUNING (+/-) buttons on the front panel.
14. Press SET.
“TIMER” appears in the display window and
the time setting has been completed.
15. Switch the system off.
The selected function is automatically
switched on and off at the time set.
To cancel or check the timer
Each time the TIMER button is pressed you can
select the time set or cancel. You can also check
the time setting status.
To activate or check the time, press the TIMER
button so that “TIMER” appears in the display
window.
To cancel the TIMER, press the TIMER button so
that “TIMER” disappears in the display window.
Operation
AP_LX-M150A(ENG)
ote
The unit can also set the clock function in power
off state.
2.When you select the CD function,
- “ON TIME” indicator appears for about
0.5seconds in the display window and then
disappears.
5. Set the hour to switch on by pressing
TUNING (+/-) buttons on the front panel.
6. Press SET to confirm the hour to switch on.
7. Set the minute to switch on by pressing
TUNING (+/-) buttons on the front panel.
8. Press SET to confirm the minute to switch on.
9. Set the hour to switch off by pressing TUNING
(+/-) buttons on the front panel.
11
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 12
RDS Function - OPTIONAL
Programme Search (PTY)
About RDS
A major benefit of RDS is its ability to encode
broadcasts with Programme Type (PTY) codes
that indicate the type of material being broadcast.
The following list shows the abbreviations used to
indicate each PTY along with an explanation of
the PTY.
This unit is equipped with RDS (Radio Data
System), which brings a wide range of information to FM radio. Now in use in many countries,
RDS is a system for transmitting station call signs
or network information, a description of station
programme type text message about the station
or specifics of musical selection and the correct
time.
RDS Tuning
When a FM station is tuned in and it contains
RDS data, the unit will automatically display the
station’s call sign and the RDS indicator will light
in the Display Window as well as indicators for
the programme type recognition (PTY), Radio
Text (RT), Clock Time (CT) and RDS services
programme (PS) if transmitted by the station.
RDS Display Options
The RDS system is capable of transmitting a
wide variety of information in addition to the initial
call sign that appears when a station is first
tuned. In normal RDS operation the display will
indicate the station name, broadcast network or
call letters. Pressing RDS on the front panel
enables you to cycle through the various data
types in the sequence:
(PS
FREQUENCY
PTY
RT
CT)
• PTY (Programme type recognition)- The name
of the programme type is shown in the Display
Window.
• RT (Radio text recognition)- The name of the
radio text is shown in the Display Window.
• CT (Time controlled by the channel)- Enables
the unit to receive the actual time and show it in
the Display Window.
• PS (Programme Service name)- The name of
the channel is shown in the Display Window.
ote
Some RDS stations may not choose to include
some of these additional features.If the data
required for the selected mode is not being
transmitted, the Display Window will show a
PTY NONE, RT NONE, CT NONE, PS NONE
message.
12
You may search for a specific Programme Type
(PTY) by following these steps:
1. Press TUNER/BAND to select FM mode.
2. Select a desired station by pressing
TUNING (+/-). When the RDS transmission is
received, the display shows the program
service name (PS) after RDS indicator
appears.
3. Press the RDS to select PTY mode.
4. To search for a different PTY, press the PRESET
(+/-) while the last PTY in use is still
displayed to scroll through the list of available
PTY types.
5. When the PTY is selected, press the
(.m/M>) within 5 seconds.
The unit will go into an automatic search
mode and attempt to find the next station
with acceptable signal strength that matches
the desired PTY type.
3/2/06
9:54 PM
Page 13
Presetting the Radio Stations
Listening to the radio
You can preset 50 stations for FM and AM.
Before tuning, make sure that you have turned
down the volume to the minimum.
1.Press TUNER/BAND to select the FM or AM
1. Press TUNER/BAND to select the FM or AM
you want in the display window.
Every time you press TUNER/BAND, FM and
AM changes alternately.
2. Press TUNING (+/-) on the front panel until
the frequency indication starts to change,then
release.
Scanning stops when the unit tunes in a station.
otes
• Tuning in automatically
Press TUNING (+/-) for more than 0.5 seconds.
• Tuning in manually
Press TUNING (+/-) briefly and repeatedly.
you want in the display window.
The last received station is tuned in.
2.Press PRESET (+/-) (or PRESET ( /
) on
the remote control) repeatedly to select the
preset station you want.
- Each time you press the button, the unit
tunes in one preset station at a time.
3.Adjust the volume by pressing VOLUME CONTROL KNOB on the front panel or VOLUME
(
/
) on the remote control repeatedly.
To listen to non-preset radio stations
• Use manual or automatic tuning in step 2.
• For automatic tuning, press and hold TUNING
(+/-) on the front panel.
Operation
AP_LX-M150A(ENG)
To turn off the radio
Press POWER to turn the unit off or select
another function mode (CD, TAPE or AUX).
3. Press PROGRAM/MEMO. on the front panel
A preset number will flash in the display window.
4. Press PRESET (+/-) (or PRESET(
/ )on
the remote control) to select the preset number you want.
5. Press PROGRAM/MEMO.
The station is stored.
6. Repeat steps 3 to 6 to store other stations.
To clear all the memorized stations
Press and hold PROGRAM/MEMO. on the front
panel for about two seconds, “CLEAR” appears
in the display window and then press CLEAR,
the stations are cleared.
For your reference
If all stations have already been entered, FULL
message will appear in the display window for a
moment and then a preset number will flash. To
change the preset number, follow the steps 5-6.
For your reference
• If an FM program is noisy
Press MODE/RIF so that “STEREO”
disappears in the display window. There will
be no stereo effect, but the reception will
improve. Press MODE/RIF again to restore
the stereo effect.
• To improve reception Reposition the supplied
antennas.
otes
• Use MODE/RIF (Radio Interference Filter)
function to switch to MONO reception if stereo
reception is distorted by noise.
• When recording the MW(AM) broadcast, beat
noises may occur. If it does, press MODE/RIF
once.
To recall presets
Press and hold PRESET (+/-)
(or PRESET ( / ) on the remote control) until the
desired preset number appears or press it repeatedly.
13
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 14
Tape Playback
Recording
Basic Playback
Wind the tape to the point recording starts.
(Use only normal tapes.)
1. Press FUNCTION repeatedly to appear
TAPE indicator.
2. Open cassette deck by pushing
STOP/EJECT(x/Z) button.
3. Insert a cassette with the tape side to the
bottom and then close deck.
Basic Setting
1. Select the function (MP3/CD, TUNER/BAND
or AUX) you want to record.
2. Open the cassette deck and insert a blank
cassette into the cassette compartment.
4. Press PLAY (B).
To Stop Play
Press STOP/EJECT (x/Z) during playback.
To Pause Play
Recording from Radio, CD or Auxiliary
source
1. Press FUNCTION button to select desired
recording source, and then press RECORD
(z) button.
The recording begins.
Press PAUSE (X) during playback.
Press this button again it to resume play.
To Play Fast Rewind or Fast Forward
After pressing REWIND/FAST FORWARD
BB ) on the front panel during
(bb/B
playback or stopping.
For your reference
When you press RECORD (z) button,
PLAY(B) button is pressed automatically.
2. To pause recording
Press PAUSE (X) button during recording.
Press PAUSE (X) button again to resume
recording.
AUTO STOP DECK
After auto stop deck plays only front side, the
unit stops automatically.
3. To stop recording
Press STOP/EJECT (x/Z).
CD to Tape Synchronized Recording
The CD synchro recording function dubs a complete CD and programmed titles automatically
into a cassette.
1. When you select CD function, press
2.
RECORD(z) button.
“REC” appears and “
” displays in
the display window.
The synchronized recording is started
automatically after about 8 seconds.
otes
• If you wish to record from the desired track,
select the desired track with CD
SKIP/SEARCH (.m/M>) before
commencing CD synchro recording.
• The function change is not possible during
recording.
14
3/2/06
9:54 PM
Page 15
CD Playback
Basic Playback
1. Press FUNCTION repeatedly to appear CD
indicator.
If no disc is loaded then “NO DISC” is
displayed.
2. Press CD OPEN/CLOSE ( Z OPEN/CLOSE)
and place the disc into the disc tray.
ote
To Play Fast Rewind or Fast Forward
After pressing CD SKIP/SEARCH
(.m/M>) buttons for more the
2 seconds on the front panel, then release
during playback,press PLAY (B/[]) at the point
you want.
ote
This function is not available to play a MP3 file.
To Repeat Play
To load an 8cm(3 inch) disc, put it onto the inner
circle of the tray.
To play one track repeatedly
Press REPEAT once during playback.
- “REPEAT 1” appears in the display.
3. Press CD OPEN/CLOSE (ZOPEN/ CLOSE)
To play all tracks repeatedly
Press REPEAT again during playback.
- “REPEAT ALL” appears in the display.
to close the disc compartment.
Audio CD: “READING” appears in the display
window, and then the total number
of tracks and the playing time are
displayed.
MP3 CD: “READING” appears in the
display window, and then the total
number of files is displayed.
4. Press CD PLAY/ PAUSE (B/[]).
To Pause Play
To cancel repeat play
Press REPEAT once more during playback.
- “Repeat indicator” disappears.
To check MP3 file information
Press the MP3 Info button during MP3 file
playback.
- The information (Title, Artist or Album) of the
MP3 file will be shown in the display window.
Press CD PLAY/ PAUSE (B/[]) during playback.
Press this button again it to resume play.
- If there is no information of the MP3 file, “NO
ID3 TAG” indicator will be shown in the display
window.
To Stop Play
- The “MP3 file name” and “ID3 TAG” should be
Press CD STOP (x) during playback.
To Skipping the Track
BB >) button
• Press the CD SKIP/SEARCH (B
to go to the next track.
bb) button
• When the CD SKIP/SEARCH (.b
is pressed once midway through a track, the
player returns to the start of that track. When it
is pressed again, a track is skipped each time
the button is pressed.
Operation
AP_LX-M150A(ENG)
named using English.
ote
This unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
15
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 16
To Program Play
About MP3
You can arrange the order of the tracks on the
discs and create your own program. The program
can contain up to 20 tracks.
• An MP3 file is audio data compressed by using
the MPEG1 audio layer-3 file-coding scheme.
We call files that have the “.mp3” file extension
“MP3 files”.
• The unit can not read an MP3 file that has not
“.mp3” file extension.
1. Press PROGRAM/MEMO. (or PROGRAM on
the remote control) on the stop mode.
2. Press CD SKIP/SEARCH (.m/M>)
buttons to select the track you want.
3. Press PROGRAM/MEMO. (or PROGRAM on
the remote control).
4. Repeat 1~3.
1. Sampling Frequency / 8 - 48kHz
5. Press CD PLAY/ PAUSE (B/[]).
2. Bit rate / 8 - 320kbps
To check program contents
3. CD-R physical format should be “ISO 9660”
Press PROGRAM/MEMO. (or PROGRAM on the
remote control) on the stop mode.
- A track and program number will be displayed.
4. If you record MP3 files using the software
To clear program contents
which cannot create a FILE SYSTEM, for
example “Direct-CD” etc., it is impossible to
playback MP3 files. We recommend that you
use “Easy-CD Creator”, which creates an
ISO9660 file system.
Press PROGRAM/MEMO. (or PROGRAM on the
remote control) on the stop mode. And then press
STOP/CLEAR on the front panel or STOP(x) on
the remote control.
5. File names should be named using 30 letters
To add program contents
6. Do not use special letters such as “/ : * ? “ < > ”
1. Press PROGRAM/MEMO. (or PROGRAM on
or less and must incorporate “.mp3” extension
e.g. “********.MP3”.
etc.
the remote control) repeatedly on the program
stop mode until “Track Number” blinks.
2. Repeat 2~5.
7. Even if the total number of files on the disc
To modify program contents
About MULTI SESSION
1. Press the PROGRAM/MEMO.
- This function recognizes the multi session disc
according to a disc of CD-ROM type.
ex) If there are MP3 files in the first session, the
MP3 file in the first session is only played.
If there are only MP3 files in the whole session, all of the MP3 files in the session are
played.
If there is Audio CD in the first session, only
the Audio CD in the first session is played.
(or PROGRAM on the remote control) to display program number you want to modify.
2. Repeat 2~4.
16
MP3 Disc compatibility with this unit is limited
as follows:
have more than 1000, it will only be shown up
to 999.
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 17
4. Maintenance and Service
Troubleshooting
Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall
outlet securely.
No sound.
• The audio cables are not
connected securely.
• Connect the audio cable into the
jacks securely.
• The power of the external source
equipment is switched off.
• Switch on the external source
equipment.
• No disc or tape is inserted.
• Insert a disc or tape.
The unit does not
start playback.
• An unplayable disc or tape is inserted. • Insert a playable disc or tape.
• The disc is placed upside down.
• Place the disc with the playback
side down.
• The disc is not placed within the
guide.
• Place the disc on the disc tray
correctly inside the guide.
• The disc is dirty.
• Clean the disc.
The remote control
does not work
• The remote control is not pointed at
the remote sensor of the unit.
• Point the remote control at the
remote sensor of the unit.
properly.
• The remote control is too far from the
unit.
• Operate the remote control
within about 23 ft (7 m).
• There is an obstacle in the path of the • Remove the obstacle.
remote control and the unit.
• The batteries in the remote
control are exhausted.
• Replace the batteries with new
ones.
Maintenance
and Service
Symptom
17
AP_LX-M150A(ENG)
3/2/06
9:54 PM
Page 18
5. Reference
[Speakers]
[TAPE]
[Amp]
AM
(MW)
[Tuner]
FM
[CD]
[General]
Specifications
Power supply
Refer to the back panel of the unit.
Power consumption
20W
Mass
3kg
External dimensions (WxHxD)
146 X 238 X 251mm
Frequency response
40 - 18000 Hz
Signal-to-noise ratio
60 dB
Dynamic range
60 dB
Tuning Range
87.5 - 108.0 MHz or 65 - 74 MHz, 87.5 - 108.0 MHz
Intermediate Frequency
10.7 MHz
Signal to Noise Ratio
55/50 dB(MONO/STEREO)
Frequency Response
60 - 10000 Hz
Tuning Range
522 - 1611 kHz or 530 - 1610 kHz
Intermediate Frequency
450 kHz
Signal to Noise Ratio
35 dB
Frequency Response
100 - 1800 Hz
Output Power
5W + 5W
T.H.D
0.5%
Frequency Response
60 - 20000 Hz
Signal-to-noise ratio
60 dB
Tape Speed
4.75 Cm/sec
Wow Flutter
0.3% (MTT -111, JIS-WTD)
F.F/REW Time
120sec (C-60)
Frequency Response
250 - 8000Hz
Signal to Noise Ratio
40dB(P/B)/38db(R/P)
Channel Separation
32dB(P/B)/30dB(R/P)
Erase Ratio
50dB (MTT-5511)
Type
1 Way 1 Speaker
Impedance
4Ω
Frequency Response
100 - 18000 Hz
Sound Pressure Level
88 dB/W (1m)
Rated Input Power
5W
Max. Input Power
10W
Net Dimensions (WxHxD)
148 x 238 x 183mm
Net Weight (1EA)
1.4kg
Designs and specifications are subject to change without notice.
18
AP_LX-M150A(ENG)
3/2/06
9:54 PM
P/NO : 3834RH0112S
Page 19