Owner`s manual | Dodge 2008 LX-48 Charger SRT8 Automobile User Manual

V07LCD15
CONNECTION
Owner’s Manual
INTRODUCTION
15” Digital / Analog
LCD TV
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
HIGH-DEFINITION TELEVISION
TROUBLESHOOTING
INFORMATION
TO RECEIVE DIGITAL/ANALOG SIGNAL,
YOU MUST CONNECT ANTENNA.
INTRODUCTION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THE APPLIANCE.
The important note is located on the rear of the cabinet.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss
of an authorization code for a CATV converter, is not intended to
be unplugged by the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in the cleaning
description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on
an unstable cart, stand, tripod, bracket,
or table. The TV may fall, causing serious
injury to someone, and serious damage to
the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the TV.
Any mounting of the appliance should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé
que sur un meuble (avec ou sans roulettes)
recommandé par le fabricant. Si vous l’
installez sur un meuble à roulettes, déplacez
les deux ensembles avec précaution. Un arrêt
brusque, l’utilisation d’une force excessive
et des surfaces irrégulières risquent de
déstabiliser l’ensemble et de le renverser.
9. VENTILATION - Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV and to protect it from overheating, these
openings must not be blocked or covered. The openings should
never be blocked by placing the TV on a bed, sofa, rug, or other
similar surface. This TV should never be placed near or over a
radiator or heat register. This TV should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your appliance
dealer or local power company. For TVs intended to operate from
battery power, or other sources, refer to the operating instructions.
2
EN
11. GROUNDING OR POLARIZATION - This TV is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the TV, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SEC TION 810-20)
ELEC TRIC
SERVICE
EQUIPMENT
GROUNDING CONDUC TORS
(NEC SEC TION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELEC TRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELEC TRODE SYSTEM
(NEC ART 250, PART H)
14. LIGHTNING - For added protection for this TV receiver during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the TV due
to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
CONNECTION
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to
determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
INTRODUCTION
INITIAL SETTING
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
5 Precautions
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are expressly approved in the manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
INFORMATION
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
TROUBLESHOOTING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
OPTIONAL SETTING
CAUTION:
WATCHING TV
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
3
EN
INTRODUCTION
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the
unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install the unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for
servicing.
• Do not place anything directly on top of the unit.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You
should record the number and other vital information here and retain this book as a permanent record of your purchase to aid
identification in case of theft.
date of purchase
dealer phone No.
serial No.
dealer purchase from
model No.
dealer address
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
5 Supplied Accessories
owner’s manual
(1EMN22201)
remote control
(NF600UD)
batteries
(AA x 2)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
5 Symbols Used in this Manual
The following is the description for the symbols used
in this manual.
Description refers to:
DTV
: Digital TV operation
TV
: Analog TV operation
• If neither symbol appears under the function
heading, operation is applicable to both.
4
EN
5 Photo Stand
When the unit is unpacked for the first time, pull the
stand to the back of this unit, and place it on a stable
position. Never use the unit with stand closed.
5 Contents
INTRODUCTION
CONNECTION
Basic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
TROUBLESHOOTING
TROUBLESHOOTING
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DTV Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DTVCC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Back Light Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Color Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OPTIONAL SETTING
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching Each Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TV Screen Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
WATCHING TV
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INITIAL SETTING
Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Photo Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONNECTION
• DTV/TV/CATV
- You can use your remote control to select channels which
are broadcast in digital format and conventional analog
format. Also, cable subscribers can access their cable TV
channels.
• Program Information Display (DTV only)
- You can display the title, contents and other information
of the current DTV program on the TV screen.
• Auto Channel Scan
- This unit automatically scans and memorizes channels
available in your area, eliminating difficult setup
procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for closed
caption supported programming.
• MTS/SAP Tuner
- Audio can be selected from the remote control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal and
no operation for 15 minutes, the unit will turn itself off
automatically.
• Sleep Timer
- This feature will automatically turned off the power of the
unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• Stereo Sound Function
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets you tune
directly to any channel using the channel number buttons
on the remote control.
• Component Video Input
• S-video Input
• AV Input
• Digital Audio Coaxial Output
INTRODUCTION
5 Features
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Other Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
INFORMATION
INFORMATION
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
5
EN
INTRODUCTION
5 Remote Control Function
1.
1
2
3
11
2.
12 3.
13
4.
14
4
15
5
6
7
8
5.
9
10
6.
7.
8.
9.
POWER button (p11)
Press to turn the unit on and off.
MUTE button (p13)
Press to turn the sound on and off.
button (p16)
SLEEP
Press to activate the sleep timer.
Number buttons (p13)
• Press to select channels.
-/ENT. button
• Press to shift the minor channel
from the major channel.
+100 button
• Press to select 100 or higher
channels. (CATV)
• Press to search if there are minor
channels on the currently selected
major channel. (DTV)
CH. K/L buttons (p13)
Press to select channels and the
external input mode.
VOL. X/Y buttons (p13)
Press to adjust the volume.
ENTER button (p11)
Press to confirm your selection.
SETUP button (p11)
Press to display the main menu.
s / B / K / L buttons (p11)
Press to move left/ right/ up/
down through the items.
10. RETURN button
Press to return to previous menu
operation.
11. INPUT button (p14)
• Press to access connected an
external device like a DVD player
or VCR.
• Press to switch between the
digital mode (DTV) and analog
mode.
12. DISPLAY button (p15)
Digital Mode (DTV)
• Press to display the channel
information, signal type and TV
setting.
Analog Mode (TV)
• Press to display the channel
number, signal type and TV
setting.
External Input Mode
• Press to display the external
input mode, signal type and TV
setting.
13. AUDIO button (p14)
Digital Mode (DTV)
Press to select the audio
language.
Analog Mode (TV)
Press to select the audio mode.
14. SCREEN MODE button (p16)
Press to select aspect ratio
available for the TV screen.
15. CH. RETURN button (p13)
Press to return to previous channel.
5 Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
1
2
3
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
6
EN
INTRODUCTION
5 Control Panel
SETUP
VOLUME
CHANNEL
INPUT
1.
2.
3.
POWER
4.
top of the unit
6.
INITIAL SETTING
5.
WATCHING TV
SETUP button (p11)
Press to display the main menu.
VOLUME X / Y buttons (p13)
Press to adjust the volume or move right(X)/left(Y)
through the main menu items.
CHANNEL K / L buttons (p13)
Press to select channels or move up/down through the
main menu items.
INPUT button (p14)
• Press to access connected an external device like a
DVD player or VCR.
• Press to switch between the digital mode (DTV) and
analog mode.
POWER button (p11)
Press to turn the unit on and off.
Infrared Sensor Window
Receives infrared rays transmitted from the remote
control.
CONNECTION
1
2
3
4
5
6
1.
2.
4.
6.
1
7.
rear of this unit
VIDEO 2
COMPONENT
AUDIO
L
R
Pb
Pr
VIDEO 1
AUDIO
S-VIDEO
VIDEO
L
R
COAXIAL
Y
2
side of the unit
3
8.
INFORMATION
5.
TROUBLESHOOTING
3.
ANT jack (p8)
RF coaxial cable connection for your antenna or
cable / satellite box.
HEADPHONE jack
Headphone connection for personal listening.
COMPONENT and AUDIO input jacks (p9)
Component video cable connection for an external
device.
Use component video and audio output jacks of an
external device.
AUDIO input jacks (p9)
RCA audio cable connection for an external device.
VIDEO input jack (p10)
RCA video cable connection for an external device.
S-VIDEO input jack (p9)
S-video cable connection for an external device.
COAXIAL (digital audio) output jack (p10)
Digital audio coaxial cable connection for a decoder or
an audio receiver.
Use digital audio input jack of an external device.
AC power cord
Connect to a standard AC outlet to supply power to
this unit.
OPTIONAL SETTING
5 Rear Panel
4
5
6
7
8
7
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
5 Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box)
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF
antenna
rear of this unit
RF coaxial cable
or
cable TV
company
*Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 11.)
Note:
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box.
Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
rear of this unit
satellite
dish
or
cable TV
company
cable/satellite box
ANT. IN RF OUT
RF coaxial cable
RF coaxial cable
*Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
8
EN
INTRODUCTION
Cables not included.
Please purchase the necessary cables at your local store.
5 External Device Connection
INITIAL SETTING
component
video cable
(green)
(blue)
(red)
rear of this unit
VIDEO 2
COMPONENT
AUDIO
L
R
Pb
Pr
VIDEO 1
AUDIO
S-VIDEO
VIDEO
L
R
COAXIAL
Y
e.g.)
CONNECTION
[Component Video Cable Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s component video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO2.
Y
Pb
Pr
COMPONENT VIDEO OUT
WATCHING TV
DVD player with the component
video output jacks
AUDIO OUT
L
R
(green) (blue)
(red)
OPTIONAL SETTING
RCA audio cable
Note:
• This unit accepts 480i / 480p / simplified 1080i video signals.
• Simplified 1080i video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.
TROUBLESHOOTING
[S-video Cable Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
rear of this unit
VIDEO 2
COMPONENT
AUDIO
L
R
Pb
Pr
VIDEO 1
AUDIO
S-VIDEO
VIDEO
L
R
COAXIAL
Y
AUDIO OUT
L
R
S-VIDEO
OUT
INFORMATION
e.g.)
DVD player with the S-video
output jack
S-video cable
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
9
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
[Video Connection]
Video connection offers standard picture quality for video devices connected to the unit.
If you connect to the unit’s video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
rear of this unit
VIDEO 2
COMPONENT
AUDIO
L
R
Pb
Pr
VIDEO 1
AUDIO
S-VIDEO
VIDEO
L
R
COAXIAL
Y
e.g.)
AUDIO OUT
L
R
camcorder
VIDEO
OUT
video game
RCA video cable
VCR
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
[Digital Audio Output Connection (for digital broadcasting only)]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
rear of this unit
VIDEO 2
COMPONENT
AUDIO
L
R
Pb
Pr
VIDEO 1
AUDIO
S-VIDEO
VIDEO
L
R
COAXIAL
Y
e.g.)
DIGITAL AUDIO
COAXIAL IN
Dolby Digital decoder
digital audio coaxial cable
10
EN
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
5 Initial Setup
Note:
Before you begin:
Make sure if the unit is connected to antenna or cable.
1 After making all the necessary connections, press
[POWER] to turn on the unit.
2 Use [Cursor K /L] to select the on-screen language
- HELPFUL HINTS -
ENGLISH
ESPAÑOL
FRANÇAIS
SET : ENTER
AJUSTE : ENTER
VALIDER : ENTER
• “INITIAL SETUP“ menu on step 3 will be displayed in
the selected language after you press [ENTER].
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [ENTER].
or
- INITIAL SETUP PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
• Scanning and memorizing the channels automatically
start.
25
AUTO PRESET CH(TV/DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
Press [SETUP].
e.g.) digital TV mode
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
• PICTURE
You can adjust the picture quality.
(Refer to “Picture Adjustment” on page 18.)
• CHANNEL SETUP
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 12.)
INFORMATION
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
TROUBLESHOOTING
3 Use [Cursor K /L] to select “AUTO PRESET CH(TV/DTV)”
5 Main Menu
OPTIONAL SETTING
SELECT : K,, L
SELECCIONE : K,, L
CHOIX : K,, L
WATCHING TV
1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH”?
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
from the choices on the right side of the TV screen.
(ENGLISH / ESPAÑOL / FRANÇAIS)
SELECT LANGUAGE
SELECCIONE EL IDIOMA
CHOISIR LA LANGUE
INITIAL SETTING
• This operation may take a few moments.
• If you connect the cable system directly, contact the CATV installer.
• If you press [POWER] or [SETUP] during “AUTO PRESET CH”,
this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SETUP” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 12.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [SETUP].
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and no
operation for several seconds after you turn on the unit, “HELPFUL
HINTS” appears. Follow the instructions listed on the TV screen.
CONNECTION
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
or
INTRODUCTION
INITIAL SETTING
• V-CHIP SETUP
You can set the viewing limitations.
(Refer to “V-chip” on page 22.)
• LANGUAGE
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to “Language Selection” on page 12.)
• CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to “Closed Caption” on page 18.)
• BACK LIGHT
You can set the desired brightness mode.
(Refer to “Back Light Setting” on page 21.)
11
EN
INITIAL SETTING
• COLOR TEMP.
You can adjust color temperature (“NORMAL”, “WARM”,
“COOL”).
(Refer to “Color Temperature” on page 21.)
• DTVCC
In addition to the basic closed caption described
on page 18, DTV has its own closed caption called
DTVCC.
(Refer to “DTV Closed Caption” on page 19.)
5 Auto Channel Scan
If you switch wires (e.g., between antenna and CATV) or if you move the unit
to a different area after the initial setting, or if you restore the DTV channel
you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1 Press [SETUP] to display the main menu.
2
Use [Cursor K/L] to select “CHANNEL SETUP”, then
press [ENTER].
e.g.) digital TV mode
or
3
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH(TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed. If
there is no analog channel, the lowest memorized
digital channel will be displayed.
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
• When no channel can be received by auto channel scan,
“NO TV SIGNALS” will be displayed on the TV screen.
• Channel settings will be saved even if the power fails.
• If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K/L] to select “IDIOMA”
or “LANGAGE”. Press [ENTER] to select “ENGLISH”. Press
[SETUP] to remove the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
5 Language Selection
You can choose English, Spanish, or French as your on-screen language.
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
Use [Cursor K/L] to select your desired preset type,
then press [ENTER].
e.g.) digital TV mode
1 Press [SETUP] to display the main menu.
2 Use [Cursor K /L] to select “LANGUAGE”, then press
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
- CHANNEL SETUP -
or
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
or
• When aerial antenna is connected, select
“AUTO PRESET CH(TV)”, “AUTO PRESET CH(DTV)” or
“AUTO PRESET CH(TV/DTV)”.
• When connected to CATV, select “AUTO PRESET CH (CATV)”.
• Scanning and memorizing the channels automatically
start.
AUTO PRESET CH(DTV)
12
EN
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
ENGLISH
ESPAÑOL
FRANÇAIS
e.g.) digital TV mode
D25
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
3 Press [SETUP] to exit.
INTRODUCTION
WATCHING TV
5 Channel Selection
5 Volume Adjustment
Select channels by pressing [CH. K/L] or [the Number buttons].
This section describes how to adjust the volume. The mute function, which
turns the sound off and on, is also described.
Use [VOL. X/Y] to adjust the audio volume.
CONNECTION
• To select the memorized channels, use [CH. K/L] or
[the Number buttons].
• To select the non-memorized channels, use
[the Number buttons].
or
To Use [the Number buttons]
VOLUME
TV
20
DTV
- When selecting digital channel 12-1
Be sure to press [–/ENT.] before entering the minor
channel number.
] to turn off and on the sound.
MUTE
20
• “MUTE” is displayed on the TV screen for a few
seconds.
OPTIONAL SETTING
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
Press [MUTE
WATCHING TV
• Press [CH. RETURN ] to return to the previously
viewed channel.
• When you select a channel larger than 100, press
[+100] first. Then use [the Number buttons] to press
the lower 2-digit numbers.
• The volume bar will be displayed at the bottom of the
TV screen when adjusting the volume.
• The volume bar display will automatically disappear in
a few seconds.
Press [MUTE ] again or [VOL. X/Y] to recover the
original volume.
TROUBLESHOOTING
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple
signals to send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by
a single network.
ATSC (digital mode)
CH4
No signal
INFORMATION
NTSC (analog mode) [Air Time]
18:00
No signal
18:30
CH4
(high definition TV)
CH4
INITIAL SETTING
- When selecting analog channel 12
19:00
CH4
CH4-1
No signal
CH4
No signal
CH4-2
CH4
CH4-1
CH4-2
19:30
20:00
20:30
major channel
minor channel
: change automatically
: change manually by using [CH. K/L]
Note:
• “NO SIGNAL” will appear on the TV screen after the minor
channel broadcast is over.
13
EN
WATCHING TV
5 Switching Each Mode
5 Switching Audio Mode
You can easily switch with the remote control to the DTV (ATSC) and TV
(NTSC) or to access an external device when they are connected to the unit.
This section describes how to switch the audio in the analog mode and how
to switch the audio language in the digital mode.
TV
Press [INPUT] repeatedly to cycle through the input
mode.
While receiving an MTS broadcast, press [AUDIO ]
repeatedly to cycle through the available audio channel.
ANALOG MODE
MAIN
DIGITAL MODE
SAP
VIDEO1
MONO
VIDEO2
• To use the video or S-video input jack on the unit,
select “VIDEO1”.
• To use the component video input jack on the unit,
select “VIDEO2”.
MAIN
SAP
MONO
: Outputs main-audio
: Outputs second audio program
: Outputs mono-audio
• The current mode will automatically disappear in a
few seconds.
DTV
Note:
• When you switch the analog mode to the digital mode,
it may take a while until the digital channel selection is
completed. The following TV screen is displayed while
switching the mode.
1 Press [AUDIO
] to display the currently selected
language and the number of available languages.
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
NOW SCANNING
2 Press [AUDIO
] repeatedly to cycle through the
available audio languages.
• Available languages differ depending on the
broadcast. “OTHER” is displayed when the audio
language cannot be acquired, or the acquired
languages are other than English, Spanish or French.
• The current mode will automatically disappear in a
few seconds.
Note:
• Pressing [AUDIO ] does not control external audio device.
14
EN
INTRODUCTION
5 Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
DTV
TV
Press [DISPLAY ].
In the digital mode, the detailed broadcasting information for the current
channel such as program title, program guides are displayed.
CONNECTION
In the analog mode, the current channel number is displayed.
Press [DISPLAY ] repeatedly to cycle through the
available display modes.
CH 25
OFF
INITIAL SETTING
BROADCASTING INFORMATION
PROGRAM GUIDE
• The current channel number is displayed at the topright corner of the TV screen.
• To clear the display, press [DISPLAY ] again.
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
1
OPTIONAL SETTING
2
3
4
WATCHING TV
[Broadcasting Information]
• The following information is displayed.
1 channel number
2 broadcast station
3 program title
4 audio language
(Refer to “Switching Audio Mode” on page 14.)
[Program Guide]
• The program guide added to broadcasting
information is displayed.
TROUBLESHOOTING
program
guide
KABC
CH 95-03
A Day of Memories
ENGLISH 1/3
A quarter-century ago, which may now
qualify as the good old days of newspapering, run-of-paper sales accounted
for 80 percent of the industry’s advertising revenues.
Next - Push L Key
Back - Push K Key
INFORMATION
Note:
• When the program guide consists of more than 6 lines, use
[Cursor K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to VIDEO1 input
jack.
VIDEO 1
• The information display will automatically disappear in a
few seconds when the closed caption is on.
15
EN
WATCHING TV
5 TV Screen Display Mode
DTV
2 types of display modes can be selected in the digital mode when the
broadcasting station is sending 16:9 video signal.
Press [SCREEN MODE
aspect ratio.
] repeatedly to switch the TV
5 Sleep Timer
The sleep timer can be set to automatically turn off the unit after an
incremental period of time.
1 Press [SLEEP
] to set the sleep timer.
SLEEP OFF
• Sleep timer display appears on the TV screen.
2 Press [SLEEP
LETTERBOX
ZOOM
[LETTERBOX]
Display the digital-supported program in full-screen.
Black borders will spread in the upper and lower
screen.
[ZOOM]
Enlarge and display the center area of the digitalsupported program.
The right and left side of image will be cut off.
Note:
• You may not switch the display mode depending on the
program.
] repeatedly to change the amount of
time until shut off.
SLEEP 120MIN.
• You can set your unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each press of [SLEEP ] will increase the time by 30
minutes.
• After set up, the sleep timer display can be called up
for checking by pressing [SLEEP ].
To Cancel the Sleep Timer
Press [SLEEP ] repeatedly until “SLEEP OFF“ is
displayed on the TV screen.
Note:
• The sleep timer setting display will automatically disappear
in a few seconds.
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be canceled.
16
EN
INTRODUCTION
OPTIONAL SETTING
5 Channel Add/Delete
The channel add/delete function lets you add the channel that was not
added by the auto channel scan due to the reception status at the initial
setting. You can also delete the unnecessary channels.
press [ENTER].
e.g.) digital TV mode
or
• ”ADD/DELETE(DTV)” or “ADD/DELETE” menu will disappear
automatically in a few seconds.
• In the digital mode (DTV), you can add or delete channels
only for major channel.
• Once you delete a DTV channel, you cannot recover the
channel without performing auto channel scan again.
(Refer to “Auto Channel Scan” on page 12.)
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
WATCHING TV
3
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
Note:
INITIAL SETTING
2 Use [Cursor K/L] to select “CHANNEL SETUP”, then
CONNECTION
6 Press [SETUP] to exit.
1 Press [SETUP] to display the main menu.
Use [Cursor K/L] to select “ADD/DELETE(DTV)” or
“ADD/DELETE”, then press [ENTER].
e.g.) digital TV mode
OPTIONAL SETTING
- CHANNEL SETUP -
or
TROUBLESHOOTING
4
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
Select the channel you want to add or delete. (Refer to
“Channel Selection“ on page 13.)
e.g.) digital TV mode
D25
INFORMATION
ADD/DELETE : DTV
5 Use [Cursor s/ B] to select “ADD” or “DELETE”.
or
• To add or delete another channels, repeat steps 4-5.
• Color of channel number displayed at the right top of
the TV screen indicates;
- Blue: The selected channel will be added.
- Red: The selected channel will be deleted.
17
EN
OPTIONAL SETTING
5 Closed Caption
5 Picture Adjustment
You can adjust brightness, contrast, color, tint and sharpness.
TV
You can view closed captioning (cc) for TV programs, movies and news.
Closed caption refer to text of dialogue or descriptions displayed on-screen
for the hearing impaired.
1 Press [SETUP] to display the main menu.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K /L] to select “PICTURE”, then press
2 Use [Cursor K /L] to select “CAPTION”, then press
[ENTER].
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
3 Use [Cursor K /L] to select the picture quality type you
want to adjust.
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
OFF
CAPTION1
CAPTION2
CONTRAST
TEXT1
COLOR
TEXT2
TINT
SHARPNESS
4 Use [Cursor s / B] to adjust the quality.
or
Cursor s
Cursor B
BRIGHTNESS
to decrease brightness
CONTRAST
to decrease contrast
to increase contrast
COLOR
to decrease color
to brighten color
TINT
to add red
to add green
SHARPNESS
to make soft
to make clear
to increase brightness
5 Press [SETUP] to exit.
Note:
• The picture adjustment setting display will automatically
disappear in a few seconds.
EN
or
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
BRIGHTNESS
or
18
e.g.) digital TV mode
[Caption Mode]
CAPTION1 and TEXT1;
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
(up to 4 lines of script on the TV screen, where it does
not obstruct relevant parts of the picture).
CAPTION2 and TEXT2;
are rarely available and broadcasters use them
only in special conditions, such as when “CAPTION1”
or “TEXT1” is not available.
• There are 3 display modes according to programs:
Paint-on mode: Displays input characters on the TV
screen immediately.
Pop-on mode: Once characters are stored in
memory, they are displayed all at
once.
Roll-up mode: Displays the characters continuously
by scrolling (max. 4 lines).
INTRODUCTION
5 DTV Closed Caption
DTV
In addition to the basic closed caption described on page 18, DTV has its
own closed caption called DTVCC. Use this menu to change the settings for
DTVCC.
Note:
1 Press [SETUP] to display the main menu.
2 Use [Cursor K /L] to select “DTVCC“, then press
INITIAL SETTING
[ENTER].
e.g.) digital TV mode
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
WATCHING TV
3 Use [Cursor K /L] to select “CAPTION SERVICE“, then
press [ENTER] repeatedly to change the setting.
[OFF]
[OFF]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
Select if you do not want
DTVCC. This is the default.
SERVICE1~6
Select one of these before
changing any other item in
“CAPTION” menu. Choose
“SERVICE1/6” under normal
circumstances.
CAPTION SERVICE
INFORMATION
OFF
TROUBLESHOOTING
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
or
OPTIONAL SETTING
• To show the closed caption on your TV screen, broadcast
signal must contain the closed caption data.
• Not all TV programs and commercials have the closed
caption or all types of the closed caption.
• Captions and texts may not match the TV voice exactly.
• Changing channels may delay the closed caption for a few
seconds.
• Adjusting or muting the volume may delay the closed
caption for a few seconds.
• Abbreviations, symbols and other grammatical shortcuts
may be used in order to keep pace with the on-screen
action. This is not a problem with the unit.
• The caption or text characters will not be displayed while
the main menu or functions display is shown.
• If a black box appears on the TV screen, this means that
the closed caption is set to the text mode. To clear the box,
select “CAPTION 1”, “CAPTION 2” or “OFF”.
• If the unit receives poor quality television signals, the
captions may contain errors, or there might be no captions
at all. Some possible causes of poor quality signals are:
- Automobile ignition noise
- Electric motor noise
- Weak signal reception
- Multiplex signal reception (ghosts or screen flutter)
• The unit retains the closed caption setting if the power fails.
• When the unit receives a special effects playback signal (i.e.,
Search, Slow and Still) from VCR’s video output channel
(CH3 or CH4), the unit may not display the correct caption
or text.
CONNECTION
3 Press [SETUP] to exit.
4 Press [SETUP] to exit.
Note:
• “CAPTION SERVICE” that you can switch differs depending
on the broadcast description.
19
EN
OPTIONAL SETTING
5 DTVCC Style
DTV
You can change the style of DTV CC such as font, color or size, etc.
1 Press [SETUP] to display the main menu.
• CAPTION SIZE
Closed captioning font size can be changed as below.
• FONT STYLE
Font style of the displayed caption can be switched as
below.
2 Use [Cursor K /L] to select “DTVCC“, then press
[ENTER].
e.g.) digital TV mode
or
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
• CHARACTER EDGE
Edge type of the displayed caption can be switched
as below.
• FORE COLOR, BACK COLOR
Font and background color of the displayed caption
can be switched as below.
• FORE OPACITY, BACK OPACITY
Text and background opacity of the displayed caption
can be switched as below.
CAPTION SIZE
3 Use [Cursor K /L] to select “USER SETTING“, then press
[ENTER] repeatedly to set to “ON”.
• Items in the dotted box are available only when
“USER SETTING“ is “ON“.
FONT STYLE
or
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
4 Use [Cursor K /L] to select an item, then press
[ENTER] repeatedly to change the setting for the item.
or
20
EN
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
MIDDLE, LARGE, SMALL
STYLE1/8
Proportional font used in the
menu screen
STYLE2/8
Monospaced with serifs
STYLE3/8
Proportionally spaced with
serifs
STYLE4/8
Monospaced with serifs
STYLE5/8
Proportionally spaced
without serifs
STYLE6/8
Casual font type
STYLE7/8
Cursive font type
STYLE8/8
Small capitals
NONE, RAISED, DEPRESSED, UNIFORM,
CHARACTER EDGE
SHADOW LEFT, SHADOW RIGHT
FORE OPACITY
SOLID, TRANSLUCENT, FLASH
FORE COLOR
WHITE, BLACK, RED, GREEN, BLUE,
YELLOW, MAGENTA, CYAN, TRANSPARENT
BACK OPACITY
SOLID, TRANSLUCENT, FLASH
BACK COLOR
BLACK, RED, GREEN, BLUE, YELLOW,
MAGENTA, CYAN, TRANSPARENT, WHITE
5 Press [SETUP] to exit.
INTRODUCTION
5 Color Temperature
You can set the desired brightness mode.
You can adjust color temperature of the TV screen.
1 Press [SETUP] to display the main menu.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K /L] to select “BACK LIGHT”, then press
2 Use [Cursor K /L] to select “COLOR TEMP.”, then press
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
e.g.) digital TV mode
or
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
NORMAL
NORMAL
WARM
DARK
COOL
OPTIONAL SETTING
BRIGHT
WATCHING TV
3 Press [SETUP] to exit.
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
INITIAL SETTING
[ENTER] repeatedly to change the setting.
CONNECTION
5 Back Light Setting
3 Press [SETUP] to exit.
TROUBLESHOOTING
INFORMATION
21
EN
OPTIONAL SETTING
5 V-chip
A. TV Rating
V-chip reads the ratings for programs, then denies access to the programs
which exceed the rating level you set. With this function, you can block
certain programming inappropriate for children.
1 Press [SETUP] to display the main menu.
4 Use [Cursor K /L] to select “TV RATING”, then press
[ENTER].
e.g.) digital TV mode
- V - CHIP SETUP -
2 Use [Cursor K /L] to select “V-CHIP SETUP“, then press
or
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
[ENTER].
e.g.) digital TV mode
- TV SETUP PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTV CC
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
5 Use [Cursor K /L ] to select the desired rating, then
press [ENTER] repeatedly to switch between “VIEW”
and “BLOCK”.
3 Use [the Number buttons] to enter the 4-digit
or
TV-Y
TV-Y7 (
TV-G
TV-PG (
TV-14 (
TV-MA (
numbers for your password.
[VIEW]
) [VIEW]
[VIEW]
) [VIEW]
) [VIEW]
) [VIEW]
PASSWORD
- - - -
Rating
• When you have not set up your password, enter 0000.
• When the password is correct, the following
“V-CHIP SETUP” menu is displayed.
See the following description for setting each item.
e.g.) digital TV mode
A... “A. TV Rating”
D page 22
B... “B. MPAA Rating”D page 23
C... “C. Change Password”
D page 24
- V - CHIP SETUP TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
A
B
C
Note:
• “DOWNLOADABLE RATING“ will be available when the unit
receives a digital broadcast using the new rating system.
• When you select a rating and set it to “BLOCK”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set the highest rating to “VIEW”, all ratings turn
to “VIEW” automatically.
• If the “PROTECTED PROGRAM” message appears during
your TV viewing, change to a channel that is not blocked.
Then, you can access “V-CHIP SETUP” menu and change the
setting to allow all TV viewing.
• To block any inappropriate programming, set your limits in
both “TV RATING” and “MPAA RATING”.
• The V-chip setting will be retained after a power failure
(except the access code reverts to 0000).
22
EN
Category
TV-Y
Appropriate for all children
TV-Y7
Appropriate for all children 7 and
older
TV-G
General audience
TV-PG
Parental guidance suggested
TV-14
Unsuitable for children under 14
TV-MA
Mature audience only
lower
higher
INTRODUCTION
B. MPAA Rating
MPAA Rating is the rating system created by MPAA (Motion Picture
Association of America).
[ENTER].
e.g.) digital TV mode
- V - CHIP SETUP -
or
Use [Cursor K /L ] to select the desired main rating,
then press [ENTER] twice to show its sub ratings.
or
TV-Y
TV-Y7 (DLSV)
TV-G
TV-PG (DLSV)
TV-14 (DLSV)
TV-MA (DLSV)
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
INITIAL SETTING
1
4 Use [Cursor K /L] to select “MPAA RATING”, then press
CONNECTION
[To Set the Sub Ratings]
As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the steps
below.
WATCHING TV
5 Use [Cursor K /L], then press [ENTER] repeatedly to
change the setting.
2 Use [Cursor K /L ], then press [ENTER] repeatedly
[BLOCK]
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Rating
Category
General audience
PG
Parental guidance suggested
PG-13
Unsuitable for children under 13
R
Restricted; under 17 requires accompanying
parent or adult guardian
NC-17
No one under 17 admitted
X
Mature audience only
Rating
FV
Fantasy Violence
TV-Y7
V
Violence
S
Sexual Situation
L
Coarse Language
TV-PG
TV-14
TV-MA
D
Suggestive Dialogue
TV-PG, TV-14
Category
G
TROUBLESHOOTING
Sub Rating
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
OPTIONAL SETTING
or
TV-PG
G
PG
PG-13
R
NC-17
X
or
to change the setting.
e.g.) TV-PG
INFORMATION
6 Press [SETUP] to exit.
6 Press [SETUP] to exit.
Note:
• Blocked sub ratings will appear beside the main rating
category in “TV RATING” menu.
• You cannot block a sub rating (D, L, S or V) if the main rating
is set to “VIEW”.
• Changing the category to “BLOCK” or “VIEW” automatically
changes all its sub ratings to the same (“BLOCK” or “VIEW”).
23
EN
OPTIONAL SETTING
C. Change Password
Although the default code “0000” is supplied with the unit, you can set
your own password.
4 Use [Cursor K /L] to select “CHANGE PASSWORD”, then
press [ENTER].
e.g.) digital TV mode
- V - CHIP SETUP -
or
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
5 Press [the Number buttons] on the remote control to
enter the new 4-digit password.
• Enter password again in “CONFIRM PASSWORD”
space.
NEW PASSWORD
_ _ _ _
CONFIRM PASSWORD
_ _ _ _
6 Press [SETUP] to exit.
Note:
• Make sure new password and confirm password must be
exactly the same. If they are different, the space is cleared
for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs. If you forget the
password, unplug the power cord for 10 seconds to restore
the password to 0000.
24
EN
INTRODUCTION
TROUBLESHOOTING
5 Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner's manual, check the following chart
once before calling for service.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust the “COLOR” in the main menu.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Bars on TV screen
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on
TV screen
• Move the unit away from nearby electric appliances. Turn off the power and wait
30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some
channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the broadcasting station.
No reception of digital signals
• Make sure auto channel scan has been completed. (Refer to “Auto Channel Scan”
on page 12.)
Auto channel scan must be completed when you set up the unit for the first time
or move it to a location where previously unavailable channels are broadcast.
• The selected channel may not be broadcasting.
• When auto channel scan is interrupted and not completed, some channels will not
be received. Make sure to complete. (Refer to “Auto Channel Scan” on page 12.)
INFORMATION
No color
TROUBLESHOOTING
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on again.
OPTIONAL SETTING
No picture or sound
WATCHING TV
• Be sure the power cord is plugged in.
• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
reset itself.
INITIAL SETTING
Remedy
No power
CONNECTION
Symptom
25
EN
TROUBLESHOOTING
Symptom
Remedy
The entered channel number
changes automatically
• Many digital channels have alternate channel numbers. The unit changes the
numbers automatically to the ones signifying the broadcasting stations. These are
the numbers used for analog broadcasts.
Remote control does not work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the infrared sensor window and the remote control.
• Test the signal output. If OK, then possible infrared sensor trouble.
(Refer to “IR Signal Check” on page 26.)
• Aim the remote control directly at the infrared sensor window on the front of the
unit.
• Reduce the distance to the unit.
• Re-insert the batteries with their polarities (+/– signs) as indicated.
Problems with Closed Caption Feature
Misspelled captions are
displayed.
• Closed captioning production companies may broadcast programs without
correcting the misspelling in a live broadcast.
Captions are not entirely
displayed, or captions are
delayed behind the dialogue.
• Captions that are delayed a few seconds behind the actual dialogue are common for
live broadcasts. Most captioning production companies can display a dialogue to a
maximum of 220 words per minute. If a dialogue exceeds that rate, selective editing is
used to insure that the captions remain up-to-date with the current TV screen dialogue.
Captions are displayed as a
white box.
No caption is displayed in the
closed caption-supported
program.
• Interference from buildings or weather conditions may cause captioning to be
incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed
caption decoder cannot read the information of the shortened program.
No caption is displayed
when playing the videotape
containing captions.
• The videotape may be illegally copied, or the caption signal might not have been
read during copying.
Black box is displayed in the
TV screen.
• The text mode is selected for caption. Select “CAPTION1”, “CAPTION2” or “OFF”.
Note:
• The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of
blue, green or red. This is not to be considered a defect in the LCD screen.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this owner's manual for more
details on correct operations.
5 Maintenance
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the unit with a soft
cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the
unit. Such chemicals may cause damage and discoloration to the exposed
surfaces.
Panel Cleaning
Wipe the panel of the unit with a soft cloth. Before cleaning the panel,
disconnect the power cord.
Servicing
Should your unit become inoperative, do not try to correct the problem
yourself. There are no user serviceable parts inside. Turn off the unit,
unplug the power cord and call our toll free customer support line found on
the cover of this manual to locate an authorized service center.
26
EN
IR Signal Check
If the remote control is not working properly, you can use an AM radio or
digital camera (including a cellular phone with built-in camera) to see if it
is sending out an infrared signal.
• With an AM radio:
Tune the AM radio station to a non-broadcasting
frequency. Point the remote control towards it,
push any button and listen. If the sound from
the radio flutters, it is receiving the remote
control’s infrared signal.
• With a digital camera
(including built-in cell phone
cameras):
Point a digital camera towards the remote control.
Push any button on the remote control and look
through the digital camera. If the infrared light
appears through the camera, the remote control is
working.
INTRODUCTION
INFORMATION
5 Glossary
Aspect Ratio
The width of a TV screen relative to its
height. Conventional TVs are 4:3 (in other
words, the TV screen is almost square);
widescreen models are 16:9 (the TV screen
is almost twice as wide as its height).
SAP (secondary audio program)
Second-audio channel delivered separately
from main-audio channel. This audio
channel is used as an alternate in bilingual
broadcasting.
HDTV (high definition TV)
Ultimate digital format that produces high
resolution and high picture quality.
SDTV (standard definition TV)
Standard digital format that is similar to the
NTSC picture quality.
NTSC
Acronym that stands for National Television
Systems Committee and the name of the
current analog broadcasting standards.
S-video
Offers higher quality images by delivering
each signal, color (c) and luminance (y)
independently of each other through
separate cables.
Password
A stored 4-digit number that allows access
to parental control features.
INITIAL SETTING
Component Video
This is a video signal format that conveys
each of 3 principal colors of light (red,
blue and green) through different signal
lines. This allows the viewers to experience
picture colors as original as it is. There are
several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
Dolby Digital
The system developed by Dolby
Laboratories to compress digital sound. It
offers stereo sound (2ch) or multi-channel
audio.
WATCHING TV
5 Cable Channel Designations
If you subscribe to cable TV, the channels are displayed as 1-135.
Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company.
The following is a chart of common cable channel designations.
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
TV Display
3
3
K
24
W+9
45
W+30
66
W+51
87
W+67
108
W+88
129
4
4
L
25
W+10
46
W+31
67
W+52
88
W+68
109
W+89
130
5
5
M
26
W+11
47
W+32
68
W+53
89
W+69
110
W+90
131
6
6
N
27
W+12
48
W+33
69
W+54
90
W+70
111
W+91
132
7
7
O
28
W+13
49
W+34
70
W+55
91
W+71
112
W+92
133
8
8
P
29
W+14
50
W+35
71
W+56
92
W+72
113
W+93
134
9
9
Q
30
W+15
51
W+36
72
W+57
93
W+73
114
W+94
135
10
10
R
31
W+16
52
W+37
73
W+58
94
W+74
115
11
11
S
32
W+17
53
W+38
74
A-5
95
W+75
116
12
12
T
33
W+18
54
W+39
75
A-4
96
W+76
117
13
13
U
34
W+19
55
W+40
76
A-3
97
W+77
118
A
14
V
35
W+20
56
W+41
77
A-2
98
W+78
119
B
15
W
36
W+21
57
W+42
78
A-1
99
W+79
120
C
16
W+1
37
W+22
58
W+43
79
W+59
100
W+80
121
D
17
W+2
38
W+23
59
W+44
80
W+60
101
W+81
122
E
18
W+3
39
W+24
60
W+45
81
W+61
102
W+82
123
5 General Specifications
5 Other Specifications
TV format:
ATSC / NTSC-M TV standard
Closed caption system:
§15.122/FCC (digital CC) §15.119/FCC (analog CC)
Channel coverage (ATSC/NTSC):
Terrestrial
VHF: 2~13 UHF: 14~69
CATV
2~13, A~W, W+1~W+94 (analog W+1~W+84),
A-5~A-1, 5A
Tuning system: Channel frequency synthesized tuning system
Channel access: Direct access keyboard,
Programmable scan, and up/down
Terminals:
Antenna input: VHF/UHF/CATV
S-video input: Mini DIN 4-pin jack x 1
Sound output: 1W, 8Ω x 2
• Designs and specifications are subject to change without notice and
without our legal obligation.
• If there is a discrepancy between languages, the default language will
be English.
G
20
W+5
41
W+26
62
W+47
83
W+63
104
W+84
125
H
21
W+6
42
W+27
63
W+48
84
W+64
105
W+85
126
75Ω unbalanced (F-type)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
1Vp-p (75Ω)
2V rms
INFORMATION
5 Electrical Specification
Video input:
RCA jack x 1
Audio input:
RCA jack x 4
Component video input:
RCA jack x 3
F
19
W+4
40
W+25
61
W+46
82
W+62
103
W+83
124
TROUBLESHOOTING
CATV channel
2
2
J
23
W+8
44
W+29
65
W+50
86
W+66
107
W+87
128
OPTIONAL SETTING
TV Display
CATV channel
5A
1
I
22
W+7
43
W+28
64
W+49
85
W+65
106
W+86
127
CONNECTION
ATSC
Acronym that stands for Advanced
Television Systems Committee and the
name of the digital broadcasting standards.
Y: 1Vp-p (75Ω)
Pb: 700mVp-p (75Ω)
Pr: 700mVp-p (75Ω)
Coaxial digital audio output:
RCA jack x1
500mVp-p (75Ω)
1
/8 inches
Headphone:
(3.5mm)
Remote control: Digital encoded infrared light system
Operating temperature:
41°F (5°C) to 104°F (40°C)
Power requirements:
120V AC +/- 10%, 60Hz +/- 0.5%
Power consumption (maximum):
35W
LCD:
15 inches XGA panel
Dimensions:
[photo stand open]
[photo stand close]
W: 18.6 inches (470mm) W: 18.6 inches (470mm)
H: 12.4 inches (313mm) H: 13.1 inches (331mm)
D: 7.8 inches (197mm) D: 4.2 inches (106mm)
Weight:
[with photo stand]
[without photo stand]
8.4 lbs.
(3.8kg) 8.0 lbs.
(3.6kg)
27
EN
LIMITED WARRANTY
This form describes the protection You will have under this Limited Warranty.
LIMITED WARRANTY PERIOD:
This Limited Warranty begins on the date of purchase of the Covered Product and continues for a period of six months.
WHAT IS COVERED:
Meijer will pay the cost of labor and repair or replacement parts in the event Your Covered Product fails to operate as a result of a mechanical or electrical
failure caused by defects in workmanship and/or materials. A mechanical or electrical failure caused by a direct result of a power surge is also covered. Parts
will be replaced with those of like kind and quality, and may be new or remanufactured. If the Covered Product cannot be repaired, if the cost of the repair
exceeds the original purchase price or if parts are not available due to the age of the Covered Product or discontinued by the manufacturer, the Covered
Product will be replaced with a product of similar features.
WHERE YOU ARE COVERED:
Coverage under this Limited Warranty is limited to the United States of America, including the District of Columbia. It does not include any Canadian or U.S.
Territories including Guam, Puerto Rico, or U.S. Virgin Islands.
WHAT IS NOT COVERED:
• PRODUCTS NOT ORIGINALLY COVERED BY A MANUFACTURER’S WARRANTY;
• ITEMS THAT ARE STILL COVERED BY THE MANUFACTURER’S WARRANTY, REGARDLESS OF WHETHER THE MANUFACTURER HONORS SUCH WARRANTY;
• PERIODIC CHECKUPS AND/OR PREVENTIVE MAINTENANCE AS DIRECTED BY THE MANUFACTURER EXCEPT AS PROVIDED HEREIN;
• INHERENT PRODUCT DEFECTS THAT ARE THE RESPONSIBILITY OF THE MANUFACTURER OR PARTS FAILURE DUE TO A MANUFACTURER’S RECALL;
• ANY AND ALL PRE-EXISTING CONDITIONS THAT OCCUR PRIOR TO THE EFFECTIVE DATE OF THIS LIMITED WARRANTY AND/OR ANY COSTS TO REPAIR ANY
PRODUCT SOLD “AS-IS” INCLUDING BUT NOT LIMITED TO FLOOR MODELS, DEMONSTRATION MODELS, ETC;
• PARTS OR REPAIRS DUE TO NORMAL WEAR AND TEAR AND ITEMS NORMALLY DESIGNED TO BE PERIODICALLY REPLACED BY THE PURCHASER DURING THE
COVERED PRODUCT’S LIFE, INCLUDING BUT NOT LIMITED TO BATTERIES, LIGHT BULBS, ETC.;
• DAMAGE FROM ACCIDENT, ABUSE, MISUSE, MISHANDLING, INTRODUCTION OF FOREIGN OBJECTS INTO THE COVERED PRODUCT, UNAUTHORIZED
MODIFICATIONS OR ALTERATIONS TO A COVERED PRODUCT, FAILURE TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS, AND EXTERNAL CAUSES
INCLUDING THIRD PARTY ACTIONS, FIRE, THEFT, INSECTS, ANIMALS, EXPOSURE TO WEATHER CONDITIONS, WINDSTORM, SAND, DIRT, HAIL, EARTHQUAKE,
FLOOD, WATER, ACTS OF GOD OR CONSEQUENTIAL LOSS OF ANY NATURE;
• LOSS OR DAMAGE CAUSED BY WAR, INVASION OR ACT OF FOREIGN ENEMY, HOSTILITIES, CIVIL WAR, REBELLION, RIOT, STRIKE, LABOR DISTURBANCE,
LOCKOUT, OR CIVIL COMMOTION;
• INCIDENTAL, CONSEQUENTIAL OR SECONDARY DAMAGES OR DELAY IN RENDERING SERVICE UNDER THIS LIMITED WARRANTY, OR LOSS OF USE DURING
THE PERIOD THAT THE COVERED PRODUCT IS AT AN AUTHORIZED SERVICE CENTER OR OTHERWISE AWAITING PARTS;
• ANY PRODUCT USED IN A COMMERCIAL SETTING OR RENTAL BASIS;
• FAILURES THAT OCCUR OUTSIDE OF THE 50 STATES OF THE UNITED STATES OF AMERICA, INCLUDING THE DISTRICT OF COLUMBIA;
• NONFUNCTIONAL OR AESTHETIC PARTS INCLUDING BUT NOT LIMITED TO PLASTIC PARTS, KNOBS, ROLLERS, BASKETS, SCRATCHES, PEELING AND DENTS;
• UNAUTHORIZED REPAIRS AND/OR PARTS;
• COST OF INSTALLATION, SET-UP, DIAGNOSTIC CHARGES, REMOVAL OR REINSTALLATION OF THE COVERED PRODUCT, EXCEPT AS PROVIDED HEREIN;
• ACCESSORIES USED IN CONJUNCTION WITH A COVERED PRODUCT;
• ANY LOSS OTHER THAN A COVERED BREAKDOWN OF THE COVERED PRODUCT;
• SERVICE WHERE NO PROBLEM CAN BE FOUND;
• BREAKDOWNS WHICH ARE NOT REPORTED WITHIN THE TERM OF THIS LIMITED WARRANTY;
• IMPROPER INSTALLATION OF COMPONENTS OR PERIPHERALS;
• CORRUPTION OF ANY RECORDING MEDIA, INCLUDING ANY PROGRAM, DATA OR SETUP INFORMATION RESIDENT ON ANY HARD DRIVES AND INTERNAL
OR EXTERNAL REMOVABLE STORAGE DEVICES, AS A RESULT OF THE MALFUNCTIONING OR DAMAGE OF AN OPERATING PART, OR AS A RESULT OF ANY
REPAIRS OR REPLACEMENT UNDER THIS LIMITED WARRANTY;
• DAMAGE TO CLOTHING;
• COLOR FADING OF PICTURE FOR ANY TELEVISION;
• BURNED-IN PHOSPHOR (INCLUDING IMAGE GHOSTING), PIXEL BURNOUT NOT IN ACCORDANCE WITH THE MANUFACTURER’S SPECIFICATIONS.
WHAT TO DO WHEN YOUR PRODUCT FAILS TO OPERATE:
• Call the 24-hour customer service toll-free number at (866) 845-9436.
Many oversights, which are not covered under this Limited Warranty, can be due to simple circumstances such as the Covered Product not being switched
on, being unplugged, or a fuse blown at the junction box. For a Covered Product that uses batteries as the primary power supply, or a remote control unit,
please check that the batteries do not need replacing or recharging.
SERVICE DELIVERABLES:
There is no deductible required to obtain service for Your Covered Product.
OTHER PROVISIONS:
Limit of Liability:
The limit of liability under this Limited Warranty is the least of the cost of (1) the purchase price of the Covered Product excluding tax and delivery costs or (2)
authorized repairs not to exceed the purchase price of the Covered Product or (3) replacement of the Covered Product with similar features or (4) reimbursement
for authorized repairs or replacement. Upon replacement, there is no longer any obligation for the replaced product under this Limited Warranty.
Limitations of Implied Warranty:
All Implied Warranties which may arise under state law, including all Implied Warranties of Merchantability or Fitness for a particular purpose, are limited to
the duration of this Warranty and do not cover incidental or consequential damages. Some states do not allow limitations on how long an Implied Warranty
lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to You. This Warranty gives You specific
legal rights, and You may also have other rights which vary from state to state.
Transferability and Renewals:
This Limited Warranty is not transferable or renewable.
Subrogation:
If We pay for a loss, We may require You to assign Us Your rights of recovery against others. We will not pay for a loss if You impair these rights to recover. Your
rights to recover from others may not be waived.
Arbitration:
In the event of a disagreement between You and Us concerning costs, either of us may make a written demand for arbitration. This must be done within
sixty (60) days after the day You filed Your claim. Each of us will select an arbitrator. The two arbitrators will select an umpire. Each of us will pay the expenses
of the arbitrator We select. The expenses of the umpire will be shared equally. Unless both of us agree otherwise, arbitration will take place in the county and
state in which You live. Local rules apply. A majority decision will be binding.
Printed in China
A7126UH
1EMN22201 *****
Download PDF

advertising