Operator`s manual | Dodge 2008 LX-49 Magnum SRT8 Automobile User Manual

X7722271404 / X772000164
99944200485
Shaft Hedge Clipper Attachment
FOR MODELS: SRM-2100SB, 2400SB, 210SB, 211SB, 225SB, 260SB,
261SB, PAS-2100, 2400, 2601, 210, 211, 225, 225VP, 225VPB, 230,
231, 260, 261, 265, 266 (NOT FOR USE ON PAS-280)
Operator’s Manual
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual and a safety manual. Both must be read and understood for proper and safe
operation. Failure to do so could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7702091904
© 08/2013 ECHO Inc.
TABLE OF CONTENTS
99944200485
TABLE OF CONTENTS
Table of Contents .............................................................................................................................. 2
Introduction ........................................................................................................................................ 3
The Operator’s Manual ................................................................................................................ 3
The Safety Manual....................................................................................................................... 3
Servicing information ......................................................................................................................... 3
Parts/Serial Number..................................................................................................................... 3
Service ......................................................................................................................................... 3
Echo Consumer Product Support ................................................................................................ 3
Warranty Registration .................................................................................................................. 3
Additional or Replacement Manuals ............................................................................................ 4
Safety................................................................................................................................................. 4
Manual Safety Symbols and Important Information ..................................................................... 4
International Symbols .................................................................................................................. 5
Personal Condition and Safety Equipment .................................................................................. 5
Equipment.................................................................................................................................... 8
Description......................................................................................................................................... 9
Contents .......................................................................................................................................... 10
Assembly ......................................................................................................................................... 11
Power Head Shaft/Lower Shaft Assembly ................................................................................. 11
Front Handle Installation ............................................................................................................ 11
Operation ......................................................................................................................................... 13
Hedge Trimming ........................................................................................................................ 13
Maintenance .................................................................................................................................... 14
Skill Levels ................................................................................................................................. 14
Maintenance Intervals................................................................................................................ 14
Lubrication ................................................................................................................................. 14
Sharpening Blades..................................................................................................................... 16
Storage ............................................................................................................................................ 18
Storage Hook Installation........................................................................................................... 18
Specifications................................................................................................................................... 19
Warranty Statements ....................................................................................................................... 20
Notes ............................................................................................................................................... 22
2
X7702091904
© 08/2013 ECHO Inc.
99944200485
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both
easy to use and full of helpful operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
The Safety Manual
Keep it in a safe place for future reference. Explains possible hazards and the measures you should take to
insure safe operation.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future reference,
write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to
4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
www.echo-usa.com or by filling out the warranty registration card supplied with your unit. Registering your
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
X7702091904
© 08/2013 ECHO Inc.
3
SAFETY
99944200485
Additional or Replacement Manuals
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at
www.echo-usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047
(800-673-1558). Always check the ECHO Web Site for updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
SAFETY
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling,
starting and stopping instructions.
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
4
X7702091904
© 08/2013 ECHO Inc.
99944200485
SAFETY
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Warning, See
Operator’s
Manual
Safety/Alert
DO NOT USE
BLADES - Line
Head Only
Wear eye, ear
and head
protection
Finger Severing
Plan retreat
pathfromfalling
objects
Wear hand
and foot
protection
Rotating Cutting
Attachment
AVOID KICKOUT.
Keep bystanders at least 15 meters
(50 feet) away.
Wear Face
Shield
Wear slip
resistant foot
wear
Beware Thrown Objects
Wear Eye Protection
Keep feet
away from
blade
Do not operate
closer than 15 M
(50 ft.) from
electrical hazards.
Keep
bystanders at
least 15 meters
(50 feet) away
Thrown
objects
Keep bystanders and helpers
away 15 m (50 ft.).
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eye protection that meets ANSI Z87.1, CE, or CSA Z94.3 requirements must be worn whenever you operate
the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the
transmission of machine vibration to your hands.
Breathing Protection
Wear a facemask to protect against dust.
X7702091904
© 08/2013 ECHO Inc.
5
SAFETY
99944200485
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work
for early morning or late afternoon hours when temperatures are cooler.
The ignition components of this machine generate an electromagnetic field during operation which
may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of ECHO
products by anyone who has a pacemaker.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon,
which affects the fingers of certain individuals, may be brought
about by exposure to vibration and cold. Exposure to vibration
and cold may cause tingling and burning sensations, followed
by loss of color and numbness in the fingers. The following
precautions are strongly recommended, because the minimum
exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and
also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held
power equipment is not required.
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling,
consult your physician before further exposing yourself to cold and vibration.
6
X7702091904
© 08/2013 ECHO Inc.
99944200485
SAFETY
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the
fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those
areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme
RSI condition is Carpal Tunnel Syndrome (CTS), which could
occur when your wrist swells and squeezes a vital nerve that
runs through the area. Some believe that prolonged exposure to
vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist
position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
All over head electrical conductors and communications wires can have electricity flow with high
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,
otherwise serious injury or death may result.
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Keep a Firm Grip
• Hold the front and rear handles with thumbs and fingers encircling
the grips.
X7702091904
© 08/2013 ECHO Inc.
7
SAFETY
99944200485
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not
work in odd positions or on ladders. Do not over reach.
Avoid Hot Surfaces
• During operation, the drive shaft housing and attachment bearing
housing may become very hot, too hot to touch. Avoid contact
during and immediately after operation.
Equipment
Use this attachment with ECHO approved models only. Serious injury may result from the use of this
attachment combined with a non approved ECHO product.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Never adjust blades when the engine is operating.
• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged
blades should not be used.
Note: ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories
which have not been tested and approved by ECHO.
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
◆
◆
◆
8
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
NEVER reach into any opening while the engine is running. Moving parts may not be visible through
openings.
X7702091904
© 08/2013 ECHO Inc.
99944200485
DESCRIPTION
DESCRIPTION
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
1
2
3
4
5
6
1. BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are
capable of cutting on either side.
2. DRIVE SHAFT ASSEMBLY - Lightweight aluminum drive shaft extends reach. 4-position shaft design
permits blade position to be rotated in 90-degree steps.
3. SAFETY DECAL – Contains important safety information that must be followed. (See Page 5)
4. LEFT HAND SHAFT GRIP - Cushioned grip for left hand.
5. GEAR HOUSING ASSEMBLY - Commercial grade, low weight, fast cutting speed. Grease fitting
simplifies lubrication.
6. BLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using
unit.
X7702091904
© 08/2013 ECHO Inc.
9
CONTENTS
99944200485
CONTENTS
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missingparts. Use the contents list to check for missing parts.
____ 1 - Shaft Hedge Clipper Attachment
____ 1 - Operator's Manual
X7722271404 / X772000164
99944200485
Shaft Hedge
Clipper
Attachment
____ 1 - Safety Manual
Operator’s Manual
____ 1 - Warranty Registration Card
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur.
The engine exhaust from this product contains chemicals known to the State of California to cause cancer.
birth defects or other reproductive harm.
____ 1 - Blade Cover
Read rules for safe operation and instructions carefully. ECHO provides an Operator’s Manual
and a Safety Manual. Both must be read and understood for proper and safe operation.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7722271404 / X772000164
____ 1 - Storage Hook Assembly
10
© 4/2011 ECHO Inc.
X7702091904
© 08/2013 ECHO Inc.
99944200485
ASSEMBLY
ASSEMBLY
Power Head Shaft/Lower Shaft Assembly
Do not perform maintenance or assembly procedures with engine running.
Parts Required:
PAS or SRM-SB Power Head w/Shaft &
Coupling
1. Set Power Head/Shaft Assembly on a level surface.
B
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn
to lock-out position.
D
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
5. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages the square upper drive shaft socket.
E
C
A
Note: Earlier model Power Heads may have shorter couplings.
Short couplings fit flush to decal point (E). New couplings
are 4-3/4 in. long, and fit flush to line (C).
Note: Lower bearing housing and head assembly must be in line with the engine.
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower
shaft hole. Insure locator pin is fully engaged by twisting
lower drive shaft. Locator pin should snap flush in coupler.
Full engagement will prevent further shaft rotation.
D
C
7. Secure lower shaft assembly to coupler by tightening
clamping knob (D).
Front Handle Installation
Note: Front loop handles/loop handles with barrier bars are not recommended for use with Hedge Clipper
attachment.
X7702091904
© 08/2013 ECHO Inc.
11
ASSEMBLY
99944200485
1. Remove front handle assembly, barrier bar (if installed), and
mounting hardware from PAS or SRM-SB power head.
2. Retain parts for future use.
12
X7702091904
© 08/2013 ECHO Inc.
99944200485
OPERATION
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a completestop before removing obstructions, clearing debris, or servicing unit. Allow
unit to cool before performing service.
Hedge Trimming
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position
unit so that exhaust is directed away from your face and body.
Hedge Clipper blades are very sharp. Touching them may
lead to severe personal injury. Avoid touching blades
whenever possible, and always wear gloves to protect
hands.
1. Always grip throttle handle with right hand and support
handle with left hand.
2. Hold trimmer firmly and squeeze throttle trigger to
accelerate engine.
3. Tilt trimmer so cutting teeth are angled slightly toward the
hedge or shrub and proceed to cut.
Never remove hands from unit when blades are moving.
The engine continues running even when the blades have stopped due to an obstruction. If this
occurs, stop the engine, disconnect ignition cable and remove the obstruction.
X7702091904
© 08/2013 ECHO Inc.
13
MAINTENANCE
99944200485
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
Component/System
MAintenance Procedure
Skill Level
Interval
Drive Shaft
Grease
1
Every 25 hours of use [1]
Gear Housing
Grease
1
Every 15 - 25 hours of use [1]
Blades
Lubrication
1
Every 15 - 25 hours of use
Blades
Sharpen
2
As needed
Blades
Adjust
2
Every 40 hours of use
Screws/Nuts/Bolts
Inspect/Tighten/Replace
1
Before Each Use
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
[1] Apply POWER BLENDXTM grease.
Lubrication
Blades
Level 1.
Parts Required:
20W Engine Oil (blade lubrication), 50-50
mixture of kerosene and 20W oil (blade
cleaning)
Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
14
X7702091904
© 08/2013 ECHO Inc.
99944200485
MAINTENANCE
1. Brush loose debris from blade and coat both sides of blade
with the 50-50 cleaning mixture.
2. Allow cleaning mixture to soften the remaining gummy
residue then wipe it from the blade.
3. Apply clean oil to the entire length of the blade. Be certain
the blade bolts are lubricated.
4. Wipe excess oil from the blade before putting the unit back
in service.
Gear Housing Assembly
Level 1.
Parts Required:
POWER BLENDXTM 14 oz. or Lithium Base
Grease.
1. Clean dirt from the grease fitting (A).
2. Carefully pump grease into fitting (A). DO NOT force
grease. Too much pressure will force grease past seals and
cause damage. Apply 1-2 pumps of grease every 15-25
hours of operation.
3. Wipe excess grease from around grease fitting.
A
Drive Shaft Assembly
Level 1.
Parts Required:
POWER BLENDXTM 8 oz. or Lithium Base
Grease.
Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
1. Remove gear housing locating screw (A) and loosen
clamping screw (B). Remove the gear housing assembly
from the drive shaft housing..
C
2. Pull the drive shaft (C) from the housing, wipe clean and
re-coat with a thin coating [1/2 oz. (15 ml)] of grease.
3. Slide the drive shaft back in the drive housing being careful
not to get dirt on the flex shaft.
B
A
X7702091904
© 08/2013 ECHO Inc.
15
MAINTENANCE
99944200485
4. Slide Gear Housing Assembly onto Drive Shaft. Be
certain the Flex Drive Shaft engages the hole in Driver
Gear..
C
Flat edge of washers (D) must be against drive shaft.
5. Align locating hole in gear housing with locator hole in
drive shaft.
A
6. Install locating screw (A). Tighten clamping screw (B).
B
D
Sharpening Blades
Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise
premature wear or internal damage may occur.
Level 2.
Parts Required:
none
Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
1. Move stop switch to stop position.
2. Disconnect spark plug wire.
A
16
X7702091904
© 08/2013 ECHO Inc.
99944200485
3. Slide blades to allow file clearance using slots (A) on bottom
of blade. Do not pry against cutting edges..
6 mm (.25 in.) radius
4. File each edge carefully. Follow the original shape of the
blade.
If a power grinder is used DO NOT allow blade to over heat.
45o
5. Lubricate blades (see “Lubrication”).
Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise
premature wear or internal damage may occur.
Blade Adjustment
Level 2.
Parts Required:
none
A
B
Hedge clipper blades are very sharp. Touching them may
lead to severe personal injury. Use long hex wrenches and
sockets with extensions when tightening blade screws and
blade locknuts to keep hands at a safe distance from sharp
blades.
1. Move stop switch to stop position.
2. Disconnect spark plug wire.
3. Tighten blade screws. (A) securely.
4. Hold blade screws (A) to prevent turning, and tighten locknuts (B).
X7702091904
© 08/2013 ECHO Inc.
17
STORAGE
99944200485
STORAGE
Always install blade cover when transporting or storing unit.
1. Clean and lubricate cutting blades and gear case.
2. Sharpen cutting blades as required.
3. Apply a light coating of clean 20W engine oil along entire length of blades and on blade bolts.
4. Install blade cover onto hedge clipper cutting blades.
5. Store hedge clipper attachment in a dry, dust free place out of the reach of children, using supplied
storage hook.
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment
shaft.
2. Slide plastic cap onto end of attachment shaft.
18
X7702091904
© 08/2013 ECHO Inc.
99944200485
SPECIFICATIONS
SPECIFICATIONS
MODEL
99944200485
Length
1250 mm (49.21 in.)
Width
83 mm (3.23 in.)
Weight
2.12 kg (4.68 lb.)
Gear Case
4.27:1
Cutter
Double Reciprocating Blade - Double Edge
Effective Length
502 mm (19.76 in.)
Pitch
35 mm (1.4 in.)
Maximum Cut
Soft Materials
25.4 mm (1 in.) Diameter
Woody Materials
13 mm (1/2 in.) Diameter
X7702091904
© 08/2013 ECHO Inc.
19
WARRANTY STATEMENTS
99944200485
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
!"#$
%!"#$
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
& 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for from
date of purchase.
EXCEPTIONS:
& '*
+/
9"
are warranted for the of the product on parts only.
& "
*
producing use will be covered for failures due to defects in material or workmanship for a period of from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
& !"#$:
#
;
manual for string head installation and maintenance instructions.
& < =* >$<99<"#/!?9 !@! COMMERCIAL APPLICATION
& 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one from the date of purchase.
& 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two from the date of purchase.
EXCEPTIONS:
& '*
+/
9"
are warranted for the of the product on parts only.
& "
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
& !"#$:
#
;
manual for string head installation and maintenance instructions.
& < =* >$<99<"#/!?9 !@! RENTAL APPLICATION - 90 DAYS WARRANTY
&B
GJ
!"#$
K:N
>$XB"9Y<<?9Z>!@$X section of
this warranty statement for [\J]
20
X7702091904
© 08/2013 ECHO Inc.
99944200485
WARRANTY STATEMENTS
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
&GJ*
*
&^J*
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. !"#$%!&()* *@$*
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
&
:
*that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. !"#$ > =
{9* $ meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
&
X
[]
|G
. Only use gasoline which
contains |G
. Gasohol which contains a +
6+7+\J}
[
]\~}/9=![]
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
&
!
+
&
X
engine speeds as listed in your operator’s manual.
&
$


&
X
&
X
of unauthorized attachments.
&
@
€

manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
&
'**
%!"#$
warranty period.
&
"
parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
&
B €
$!/ $
Manuals.
&
$
screen.
&
<ƒ
[^J]
ƒ
ƒ
&
X

with recommended grease or oil change intervals.
&
X
#!X?„<"® beyond recommended capacity.
&
X
+
&
<
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COMZ
%
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
€
9
!"#$
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
9
'@9?!'$<><9@"B:<>B>$!
OR USE and any implied warranty of MERCHANTABILITY!"#$
€
9
9
!"#$
99922201032
11/18/2011
X7702091904
© 08/2013 ECHO Inc.
21
NOTES
99944200485
NOTES
22
X7702091904
© 08/2013 ECHO Inc.
99944200485
X7702091904
© 08/2013 ECHO Inc.
NOTES
23
S07100001001/S07100999999
24
Download PDF

advertising