Dodge 2008 PM Caliber Automobile User Manual

filename[D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CEL.fm]
masterpage:Right
4-182-049-11(1)
Multi Channel AV
Receiver
Operating Instructions
STR-DN2010
©2010 Sony Corporation
model name1[STR-DN2010]
[4-182-049-11(1)]
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB02REG_STR-DN2010-CEL.fm4-182049-11(1)
masterpage: Left
For customers in the United
States
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc.
Do not place the naked flame sources such as lighted
candles on the apparatus.
Owner’s Record
The model and serial numbers are located on the rear
of the unit. Record these numbers in the space
provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Model No. _____________________________________________________
Serial No. ______________________________________________________
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and
do not place objects filled with liquids, such as
vases, on the apparatus.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible
AC outlet. Should you notice an abnormality in the
unit, disconnect the main plug from the AC outlet
immediately.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or
the like.
Important Safety Instructions
The unit is not disconnected from the mains as long
as it is connected to the AC outlet, even if the unit
itself has been turned off.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
This symbol is intended to alert
the user to the presence of the Hot
Surface that may be hot if it is
touched during the normal
operation.
This equipment has been tested and found to comply
with the limits set out in the EMC Directive using a
connection cable shorter than 10 feet (3 meters).
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11)Only use attachments/accessories specified by
the manufacturer.
2GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB02REG_STR-DN2010-CEL.fm
12)Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
masterpage: Right
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
To reduce the risk of electric shock, the speaker cord
should be connected to the apparatus and the
speakers in accordance with the following
instructions.
1) Disconnect the AC power cord from the MAINS.
2) Strip 10 to 15 mm of the wire insulation of the
speaker cord.
3) Connect the speaker cord to the apparatus and
the speakers carefully so as not to touch the core
of speaker cord by hand. Also disconnect the AC
power cord from the MAINS before
disconnecting the speaker cord from the
apparatus and the speakers.
The following FCC statement
applies only to the version of
this model manufactured for
sale in the U.S.A. Other
versions may not comply with
FCC technical regulations.
For customers in Europe
NOTE:
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. The recycling of materials
will help to conserve natural resources. For more
detailed information about recycling of this product,
please contact your local Civic Office, your
household waste disposal service or the shop where
you purchased the product.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
continued
3GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB02REG_STR-DN2010-CEL.fm4-182049-11(1)
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this product
shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical
symbols for mercury (Hg) or lead (Pb) are added if
the battery contains more than 0.0005% mercury or
0.004% lead.
By ensuring these batteries are disposed of correctly,
you will help prevent potentially negative
consequences for the environment and human health
which could otherwise be caused by inappropriate
waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this battery
should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the applicable
collection point for the recycling of electrical and
electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product safely.
Hand the battery over to the applicable collection
point for the recycling of waste batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
Notice for customers: The following
information is only applicable to
equipment sold in countries applying
EU Directives.
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan. The Authorized Representative for
EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters
please refer to the addresses given in separate
service or guarantee documents.
masterpage: Left
About This Manual
• The instructions in this manual are for model
STR-DN2010. Check your model number by
looking at the lower right corner of the front panel.
In this manual, the USA model is used for
illustration purposes unless stated otherwise. Any
difference in operation is clearly indicated in the
text, for example, “European model only”.
• The instructions in this manual describe the
controls on the supplied remote. You can also use
the controls on the receiver if they have the same
or similar names as those on the remote.
On copyrights
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
** Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol,
DTS-HD and DTS-HD Master Audio are
trademarks of DTS, Inc. © 1996-2008 DTS, Inc.
All Rights Reserved.
This receiver incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
SIRIUS, XM and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All rights reserved. Service not
available in Alaska and Hawaii.
The font type (Shin Go R) installed in this receiver
is provided by MORISAWA & COMPANY LTD.
These names are the trademarks of MORISAWA &
COMPANY LTD., and the copyright of the font also
belongs to MORISAWA & COMPANY LTD.
4GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB02REG_STR-DN2010-CEL.fm
masterpage: Right
iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
All other trademarks and registered trademarks are
of their respective holders. In this manual, ™ and ®
marks are not specified.
NO LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Sony Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
MPEG Layer-3 audio coding technology and patents
licensed from Fraunhofer IIS and Thomson.
“x.v.Color (x.v.Colour)” and “x.v.Color
(x.v.Colour)” logo are trademarks of Sony
Corporation.
“BRAVIA” is a trademark of Sony Corporation.
“PlayStation” is a registered trademark of Sony
Computer Entertainment Inc.
“S-AIR” and its logo are trademarks of Sony
Corporation.
DLNA and DLNA CERTIFIED are trademarks
and/or service marks of the Digital Living Network
Alliance.
VAIO is a trademark of Sony Corporation.
Microsoft, Windows, Windows Vista, and Windows
Media are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or
other countries.
Intel, Intel Core, and Pentium are trademarks or
registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.
Rhapsody and the Rhapsody logo are trademarks
and/or registered trademarks of RealNetworks, Inc.
SHOUTcast® is a registered trademark of AOL
LLC.
THIS PRODUCT IS LICENSED UNDER THE
VC-1 PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF
A CONSUMER TO
(i) ENCODE VIDEO IN COMPLIANCE WITH
THE VC-1 STANDARD (“VC-1 VIDEO”)
AND/OR
(ii) DECODE VC-1 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED TO
PROVIDE VC-1 VIDEO.
5GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELTOC.fm
masterpage: Left
Table of Contents
About This Manual........................................4
Supplied accessories......................................8
Description and location of parts...................9
Getting started .............................................18
Connections
1: Installing the speakers .............................19
2: Connecting the speakers ..........................21
3: Connecting the TV ..................................23
4a: Connecting the video components.........25
4b: Connecting the audio components ........34
5: Connecting the antennas (aerials)............35
6: Inserting the wireless transmitter/
transceiver...............................................36
7: Connecting to the network ......................37
8: Connecting the AC power cord
(mains lead) ............................................39
Preparing the Receiver
Initializing the receiver ................................39
Setting the speakers .....................................40
Calibrating the appropriate speaker settings
automatically (Auto Calibration)............42
Configuring the network settings of the
receiver ...................................................49
Preparing a computer to use as a server ......50
Guide to on-screen display operation ..........52
Basic Operations
Playback ......................................................54
Enjoying sound/images from the components
connected to the DIGITAL MEDIA
PORT ......................................................56
Using the Sleep Timer .................................59
Recording using the receiver .......................60
Tuner Operations
Listening to FM/AM radio.......................... 61
Presetting FM/AM radio stations
(Preset Tuning)....................................... 63
Receiving RDS broadcasts.......................... 64
(European model only)
Listening to Satellite Radio......................... 65
(USA model only)
Connecting a satellite radio tuner ............... 66
Preparing to listen to a satellite radio.......... 66
Selecting a channel of the satellite radio .... 67
Presetting satellite radio channels............... 69
Restricting access to specific channels
(Parental Lock) ...................................... 70
Enjoying Surround Sound
Selecting the sound field............................. 73
Enjoying the surround effect at low volume
levels (NIGHT MODE) ......................... 77
Resetting sound fields to the initial
settings ................................................... 77
Using Network Features
About the network functions of the
receiver................................................... 78
Enjoying content stored on the server......... 78
Using a controller........................................ 81
Listening to Rhapsody ................................ 83
(USA model only)
Listening to SHOUTcast............................. 86
Features of the Setup Manager application
software.................................................. 88
6GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELTOC.fm
masterpage: Right
“BRAVIA” Sync Features
Adjusting Settings
What is “BRAVIA” Sync? .......................... 89
Preparing for the “BRAVIA” Sync ............. 90
Playing back components with one-touch
operation (One-Touch Play)................... 91
Enjoying the TV sound from the speakers
connected to the receiver
(System Audio Control) ......................... 92
Turning off the receiver with the TV
(System Power-Off) ............................... 93
Enjoying movies with the optimum sound
field (Theater/Theatre Mode Sync)........ 93
Using the Settings menu............................107
Auto Calibration menu ..............................108
Speaker Settings menu ..............................109
Surround Settings menu ............................113
EQ Settings menu......................................114
Audio Settings menu .................................114
Video Settings menu..................................116
HDMI Settings menu.................................117
Network Settings menu .............................118
System Settings menu ...............................121
Operating without connecting to a TV ......122
S-AIR Operations
About S-AIR products ................................ 94
Setting up an S-AIR product....................... 95
Enjoying the system’s sound in another
room ....................................................... 98
Changing the channel
for better sound transmission ............... 100
Stabilizing S-AIR reception ...................... 101
Enjoying the S-AIR receiver while the S-AIR
main unit is in standby mode ............... 102
Using the Remote
Programming the remote ...........................130
Clearing all the contents of the remote’s
memory.................................................135
Additional Information
Precautions ................................................135
Troubleshooting.........................................137
Specifications ............................................145
Index ..........................................................148
Other Operations
Switching between digital and analog audio
(INPUT MODE) .................................. 103
Enjoying the sound/images from other inputs
(Input Assign) ...................................... 104
Using a bi-amplifier connection................ 106
7GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELTOC.fm
Supplied accessories
•
•
•
•
•
•
•
Operating Instructions (this manual)
Quick Setup Guide
GUI Menu List
Software License Information (1)
Setup Manager CD-ROM (1)
VAIO Media plus CD-ROM (1)
FM wire antenna (aerial) (1)
masterpage: Left
Inserting batteries into the
remote
Insert two R6 (size-AA) batteries in the
RM-AAP055 (USA model only) or
RM-AAP056 (European model only) Remote
Commander.
Observe the correct polarity when installing
batteries.
• AM loop antenna (aerial) (1)
• Remote commander (1)
– RM-AAP055 (USA model only)
– RM-AAP056 (European model only)
Notes
• R6 (size-AA) batteries (2)
• Optimizer microphone (ECM-AC2) (1)
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the programmed
remote codes may be cleared. If this happens,
program the remote codes again (page 130).
• When the remote no longer operates the receiver,
replace all the batteries with new ones.
8GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Right
Description and location of parts
Front panel
1
qh
2
qg
3
4
qf
A ?/1 (on/standby)
Turns the receiver on or off (page 39, 63, 77).
B Remote sensor
Receives signals from remote commander.
C White indicator
Lights up when the receiver is turned on.
D MULTI CHANNEL DECODING indicator
Lights up when multi channel audio signals are
decoded (page 139).
E Display
Displays the current status of the selected
component or a list of selectable items (page 10).
F INPUT SELECTOR +/–
Selects the input source to play back (page 55,
60, 103).
G MUTING (page 55)
5
qd
7
6
qs qa
0
8
9
H MASTER VOLUME
Adjusts the volume level of all speakers at the
same time (page 55).
I VIDEO 2 IN jacks (page 32)
J AUTO CAL MIC jack (page 43)
K DISPLAY
Selects the information displayed on the display
(page 127).
L DIMMER
Adjusts the brightness of the display.
M INPUT MODE
Selects the input mode when the same
components are connected to both digital and
analog jacks (page 103).
N 2CH/A.DIRECT, A.F.D., MOVIE, MUSIC
(page 73, 75)
O SPEAKERS (page 42)
P PHONES jack
Connects to headphones (page 137).
9GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Left
Indicators on the display
1
2
LH SW RH
L
C
R
SL
S
SR
3
4
5 6
7
8
ARC
D + EX TrueHD NEO 6
PL ll x z ANALOG HDMI COAX OPT
S –AIR
EQ RDS CAT MEM DTS – HD MSTR HI RES LBR
LF E
D.RANGE SIRIUS ST
DTS –ES 96 24 LPCM SLEEP BI–AMP SP A B
SB L SB SB R
qj
qh
qg qf
qd
qs
qa
q;
9
Indicator and explanation
Indicator and explanation
A SW
D Dolby Digital Surround indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding
Dolby Digital format signals.
Lights up when the audio signal is output from
the SUBWOOFER jack.
B Dolby Pro Logic indicators
Lights up one of the respective indicators when
the receiver performs Dolby Pro Logic
processing. This matrix surround decoding
technology can enhance input signals.
PL
PL II
PL IIx
PL IIz
Dolby Pro Logic
Dolby Pro Logic II
Dolby Pro Logic IIx
Dolby Pro Logic IIz
Note
These indicators may not light up depending on
the speaker pattern setting.
C Input indicators
Light up to indicate the current input.
ANALOG
Lights up when
– no digital signal is being input.
– INPUT MODE is set to “ANALOG”.
– the “A. DIRECT” is being selected.
HDMI
The receiver recognizes a component connected
via an HDMI IN jack.
COAX
Lights up when digital signal is input through the
COAXIAL jack (page 103).
OPT
Lights up when digital signal is input through the
OPTICAL jack (page 103).
ARC
Lights up when TV input is selected and the
Audio Return Channel (ARC) signals are
detected.
D
D EX
D+
TrueHD
Dolby Digital
Dolby Digital Surround EX
Dolby Digital Plus
Dolby TrueHD
Note
When playing a Dolby Digital format disc, be
sure that you have made digital connections and
that INPUT MODE is not set to “ANALOG”
(page 103).
E NEO:6
Lights up when DTS Neo:6 Cinema/Music
decoder is activated (page 74).
F DTS-HD indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding
DTS-HD format signals.
DTS-HD MSTR DTS-HD Master Audio
DTS-HD HI RES DTS-HD High Resolution
Audio
DTS-HD Low Bit Rate
DTS-HD LBR
Audio
G S-AIR
Lights up when the S-AIR transmitter (not
supplied) is inserted.
H SP A/SP B/SP A B
Lights up according to the front speaker system
used (page 42).
However, these indicators do not light up if the
speaker output is turned off or if headphones are
connected.
I BI-AMP
Lights up when surround back speakers
selection is set to “BI-AMP” (page 106).
10GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Right
Indicator and explanation
Indicator and explanation
J SLEEP
Lights up when the Sleep Timer is activated.
Q Playback channel indicators
The letters (L, C, R, etc.) indicate the channels
being played back. The boxes around the letters
vary to show how the receiver downmixes the
source sound (based on the speaker settings).
K LPCM
Lights up when the receiver is decoding the
Linear PCM signals.
L DTS(-ES) indicators
Lights up one of the respective indicators when
the receiver is decoding the corresponding DTS
format signals.
DTS
DTS-ES
DTS 96/24
DTS
DTS-ES
DTS 96 kHz/24 bit
Note
When playing a DTS format disc, be sure that
you have made digital connections and that
INPUT MODE is not set to “ANALOG”
(page 103).
M Tuning indicators
Lights up when the receiver tunes in radio
stations, or satellite radio stations.
RDS (European model only)
A station that provides RDS services is tuned in.
CAT (USA model only)
The category mode is selected during the
satellite radio operation.
MEM
A memory function, such as Preset Memory
(page 63), etc., is activated.
SIRIUS (USA model only)
The SiriusConnect Home tuner is connected and
“SIRIUS” is selected.
ST
Stereo broadcast
LH
RH
L
R
C
SL
SR
S
SBL
SBR
SB
Front Left High
Front Right High
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components
obtained by Pro Logic
processing)
Surround Back Left
Surround Back Right
Surround Back (the
surround back components
obtained by 6.1 channel
decoding)
Example:
Speaker pattern: 3/0.1
Recording format: 3/2.1
Sound Field: A.F.D. AUTO
N EQ
Lights up when the equalizer is activated.
O D.RANGE
Lights up when dynamic range compression is
activated (page 113).
P
Lights up when the disc being played back
contains an LFE (Low Frequency Effect)
channel and the LFE channel signal is actually
being reproduced.
11GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Left
Rear panel
1
COMPONENT VIDEO
9
2 1
2 3
4
5
ASSIGNABLE (INPUT ONLY)
7
8
7
A DIGITAL INPUT/OUTPUT section
OPTICAL IN jacks (page 23, 29,
30, 31)
6
E S-AIR section (page 36)
EZW-T100 slot
CAUTION
(with cover)
Please do not remove the slot
cover until you want to install
the wireless transmitter.
COAXIAL IN jack (page 29, 30,
31)
HDMI IN/OUT* jacks (page 23,
26)
F SPEAKERS section (page 21)
B ANTENNA section
FM ANTENNA jack (page 35)
AM ANTENNA terminals
(page 35)
SIRIUS jack (USA model only)
(page 66)
G AUDIO INPUT/OUTPUT section
White (L)
Red (R)
Black
AUDIO IN/OUT jacks
(page 23, 34)
AUDIO OUT jack (page 21)
C DMPORT section
DMPORT jack (page 34)
D NETWORK section
LAN ports (switching hubs)
(page 38)
12GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
H VIDEO/AUDIO INPUT/OUTPUT
section (page 29, 31, 32)
White (L)
AUDIO IN/OUT jacks
Red (R)
Yellow
VIDEO IN/OUT* jacks
I COMPONENT VIDEO INPUT/
OUTPUT section (page 23, 29, 30,
31)
Green
(Y)
Blue
(PB/CB)
Y, PB/CB, PR/CR IN/OUT*
jacks
masterpage: Right
Remote commander
You can use the supplied remote to operate the
receiver and to control the Sony audio/video
components that the remote is assigned to
operate.
You can also program the remote to control
non-Sony audio/video components. For
details, see “Programming the remote”
(page 130).
• RM-AAP055 (USA model only)
• RM-AAP056 (European model only)
wg
wf
wd
ws
1
2
3
Red
(PR/CR)
* You can watch the selected input image when you
connect the MONITOR OUT or HDMI TV OUT
jack to a TV (page 23).
4
wa
w;
ql
5
6
7
qk
qj
8
9
0
qh
qg
qf
qa
qd
qs
continued
13GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
Name and function
A ?/1 (on/standby)
Turns the receiver on or sets it to the standby
mode.
Saving the power in standby mode
When “Control for HDMI” (page 90),
“Network Standby” (page 120) and “S-AIR
Standby” (page 102) are set to “OFF”.
B AV ?/1a) (on/standby)
Turns on or off the audio/video components that
the remote is programmed to operate.
To turn the TV on or off, press TV (W) and
then press AV ?/1.
If you press ?/1 (A) at the same time, it will
turn off the receiver and other components
(SYSTEM STANDBY).
Note
The function of the AV ?/1 changes
automatically each time you press the input
buttons (D).
C AMP
The button lights up and activates the receiver
operation (page 122).
D Input buttons (VIDEO 1b))
Selects the component you want to use. When
you press any of the input buttons, the receiver
turns on. The buttons are initial assigned to
control Sony components. You can program the
remote to control non-Sony components
following the steps in “Programming the
remote” on page 130.
Numeric buttonsa) (number 5b))
Press SHIFT (V), then press numeric buttons
to
– preset/tune to preset stations.
– select track numbers. Press 0/10 to select track
number 10.
– select channel numbers.
Press TV (W), then press the numeric buttons
to select the TV channels.
-/--a)
Press SHIFT (V), then press -/-- to select the
channel entry mode, either one or two digit.
Press TV (W), then press -/-- to select the TV
channel entry mode.
>10a)
Press SHIFT (V), then press >10 to select track
numbers over 10.
masterpage: Left
Name and function
ENTERa)
Press SHIFT (V), then press ENTER to enter
the value after selecting a channel, disc or track
using the numeric buttons.
Press TV (W), then press ENTER to enter the
value of Sony TV.
MEMORY
Press SHIFT (V), then press MEMORY to
store a station during tuner operation.
/a) (Text) (RM-AAP056 only)
Press TV (W), then press / to display text
information.
E SOUND FIELD +/–
Selects a sound field (page 73).
F Color buttonsa)
Displays an operation guide on the TV screen
when the color buttons are available. Follow the
operation guide to perform a selected operation.
G GUI MODE
Displays the GUI menu on the TV screen.
H TOOLS/OPTIONSa)
Displays and selects items from the option
menus.
Press TV (W), then press TOOLS/OPTIONS to
display the options of Sony TV.
I MENU, HOMEa)
Displays the menu to operate the audio/video
components.
Press TV (W), then press HOME to display the
menus of Sony TV.
J ./>a), m/Ma), Na)b), Xa), xa)
Skip, backward/forward, play, pause, stop
operation.
a)
< / <
Replay the previous scene or fast forward the
current scene.
CATEGORY +/– (RM-AAP055 only)
Selects a category for satellite tuner (page 129).
CATEGORY MODEb) (RM-AAP055 only)
Selects the category mode for satellite tuner
(page 129).
TUNING +/–a)
Scans a station.
D.TUNING
Enters direct tuning mode (page 128).
14GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
Name and function
K
masterpage: Right
Name and function
TV CH +/–a)b) (RM-AAP055 only)
PROG +/–a)b) (RM-AAP056 only)
P DISC SKIPa)
Skips disc when using a multi-disc changer.
Press TV (W), then press TV CH +/– or
PROG +/– to select preset TV channels.
Q RETURN/EXIT Oa)
Returns to the previous menu or exits the menu
while the menu or on-screen guide is displayed
on the TV screen.
Press TV (W), then press RETURN/EXIT O
to return to the previous menu of Sony TV.
PRESET +/–a)b)
Selects preset stations or channels.
cb)/C (RM-AAP056 only)
In text mode: Press TV (W), then press c/C
to select the next or previous page.
L F1/F2a)
Press BD or DVD (D), then press F1 or F2 to
select a component.
• DVD/HDD COMBO
F1: HDD
F2: DVD disc, Blu-ray Disc
• DVD/VCR COMBO
F1: DVD disc, Blu-ray Disc
F2: VCR
SLEEP
Activates the Sleep Timer function and the
duration which the receiver turns off
automatically (page 59).
M BD/DVD TOP MENUa), MENUa)
Displays the menu or on-screen guide on the TV
screen. Then, use V/v/B/b (R) and
(R) to
perform menu operations.
TV INPUTa) (RM-AAP055 only)
a) (Input select) (RM-AAP056 only)
Press TV (W), then press TV INPUT or
to
select the input signal (TV input or video input).
a) (Text hold) (RM-AAP056 only)
In text mode: Press TV (W), then press
hold the current page.
to
WIDEa) (RM-AAP055 only)
a)
(Wide mode) (RM-AAP056 only)
Press TV (W), then press WIDE or
repeatedly to select the wide picture mode.
a)
N MUTING (RM-AAP055 only)
a) (RM-AAP056 only)
Turns off the sound temporarily. Press the
button again to restore the sound.
Press TV (W), then press MUTING or
to
activate the TV’s muting function.
O TV VOL +/–a) (RM-AAP055 only)
+/–a) (RM-AAP056 only)
Press TV (W), then press TV VOL +/– or
+/– to adjust the TV volume level.
R
a)
a)
, V/v/B/b
Press V/v/B/b to select the menu items, then
press
to enter the selection.
S GUIDEa) (RM-AAP055 only)
a)
(Guide) (RM-AAP056 only)
Press TV (W), then press GUIDE or
display the on-screen program guide.
to
T DISPLAYa)
Views information on the display.
(RM-AAP055 only) Press TV (W), then press
DISPLAY to display information of TV.
,
(Info, Text reveal) (RM-AAP056
only)
Press TV (W), then press
to display
information such as current channel number and
screen mode.
In text mode: Press TV (W), then press
to
reveal hidden information (e.g. answers to a
quiz).
U NIGHT MODE
Activates the Night Mode function (page 77).
V SHIFT
The button lights up and activates the buttons
with pink printing.
W TV
The button light up and activates the buttons
with yellow printing.
X THEATER (RM-AAP055 only)
THEATRE (RM-AAP056 only)
Sets the optimal picture settings automatically
for watching movies when you connect a Sony
TV that is compatible with the THEATER or
THEATRE button function (page 93).
Y RM SET UP
Set up the remote.
MASTER VOL +/–a) (RM-AAP055 only)
+/–a) (RM-AAP056 only)
Adjusts the volume level of all speakers at the
same time.
continued
15GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Left
a)
See the table on page 17 for information on the
buttons that you can use to control each
component.
b)
The following buttons have tactile dots. Use the
tactile dots as reference when operating the
receiver.
– RM-AAP055 only: number 5, VIDEO 1, N,
CATEGORY MODE, TV CH +, PRESET +
– RM-AAP056 only: number 5, VIDEO 1, N,
PROG +, PRESET +, c
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
16GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB03DES_STR-DN2010-CEL.fm
masterpage: Right
To control other Sony components
DVD
Blu-ray HDD PSX Video CD Digital DSSa) Digital Tape DAT CD
player,
Disc Recorder
player,
CATV
satellite/ deck deck player,
DVD/VCR player
LD terminala)
terrestrial A/B
MD
combo
player
receiverb)
deck
TV
VCR
B AV ?/1
z
z
z
z
z
z
z
z
z
z
D Numeric
z
z
z
z
z
z
z
z
z
z
-/--, >10
z
z
z
z
z
z
z
z
z
z
ENTER
z
z
z
z
z
z
zd)
z
z
z
Name
z
z
z
z
z
z
ze) z
z
z
DIGITAL
MEDIA
PORT
device
z
buttons
b)
(Text)
z
z
z
F Color buttons
z
zc)
z
z
H TOOLS/
z
z
z
z
z
z
z
z
z
z
OPTIONS
I MENU, HOME
z
z
z
z
z
z
J ./>
z
z
z
z
z
z
z
z
z
z
<
/
<
z
z
z
z
z
z
z
z
z
z
z
z
zg)
z
z
z
z
m/TUNING –,
M/TUNING +
z
z
z
z
z
z
z
N, X, x
z
z
z
z
z
z
z
z
K PRESET +/–,
z
z
z
z
z
zd)
z
z
z
L F1/F2
z
z
M BD/DVD TOP
z
z
z
z
z
z
z
z
z
z
z
z
z
TV CH +/–a),
PROG +/–b)
z
MENU, BD/DVD
MENU
TV INPUTa),
b)
(Input
b)
select),
(Text hold),
b)
WIDEa),
(Wide mode)
z
N MUTINGa),
z
O MASTER
z
b)
VOL +/–a),
TV VOL +/–a),
+/–b)
P DISC SKIP
Q RETURN/
z
zf)
z
z
z
z
EXIT O
R V/v/B/b,
z
S GUIDEa),
z
b)
z
z
z
z
z
z
zc)
z
z
z
z
z
z
z
z
z
(Guide)
T DISPLAY
a)
RM-AAP055 only.
b)
RM-AAP056 only.
c) DVD player only.
d)
z
z
z
z
e)
Deck B only.
f)
Video CD player
g) m/M only.
z
z
only.
LD player only.
17GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Getting started
You can enjoy your audio/video components connected to the receiver by following the simple
steps below.
Installing and connecting the speakers
See “1: Installing the speakers” (page 19) and “2: Connecting the speakers” (page 21).
Checking the connection appropriate for your components
Connecting the TV and video components
COMPONENT VIDEO
The image quality depends on the connecting jack. See the illustration on the
right. Select the connection according to the jacks on your components.
Y
HDMI
PB/CB
VIDEO
PR/CR
Q: Does your TV have an HDMI jack?
t No: See the connection for a TV without an HDMI jack (page 23).
t Yes: See the connection for the TV with HDMI jack (page 23).
Digital
Q: Does your video component have an HDMI
jack?
Analog
High quality image
t No: See “Connecting components without HDMI jacks” (page 28).
t Yes: See “Connecting components with HDMI jacks” (page 25).
Connecting the audio components
See “4b: Connecting the audio components” (page 34).
Setting the audio output settings on the connected components
To output multi channel digital audio, check the digital audio output setting on the connected components.
For a Blu-ray Disc player, check that “Audio (HDMI)”, “Dolby Digital (Coaxial/Optical)”, and “DTS (Coaxial/Optical)”
are set to “Auto”, “Dolby Digital” and “DTS” respectively (as of March 2010).
For a “PlayStation 3”, check that “BD Audio Output Format” is set to “Bitstream” (with system software version 3.15).
For details, refer to the operating instructions supplied with the connected components.
Preparing the receiver
See “8: Connecting the AC power cord (mains lead)” (page 39) and “Initializing the receiver” (page 39).
Setting the speakers
Select the speaker pattern, then perform Auto Calibration. For details, see “Setting the speakers” (page 40) and “Calibrating
the appropriate speaker settings automatically (Auto Calibration)” (page 42).
Note
You can check the speaker connection using “Test Tone” (page 111). If the sound is not output correctly, check the speaker
connection and make the settings explained above again.
18GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
1: Installing the speakers
This receiver allows you to use a 7.1 channel
system (7 speakers and one subwoofer).
Example of speaker system
configuration
5.1 channel speaker system
To fully enjoy theater-like multi channel
surround sound requires five speakers (two
front speakers, a center speaker, and two
surround speakers) and a subwoofer (5.1
channel).
7.1 channel speaker system
using surround back speakers
You can enjoy high fidelity reproduction of
DVD or Blu-ray Disc software recorded sound
in 6.1 channel or 7.1 channel format if you
connect additional one surround back speaker
(6.1 channel) or two surround back speakers
(7.1 channel).
7.1 channel speaker system
using front high speakers
You can enjoy vertical sound effects if you
connect additional two front high speakers
(7.1 channel) in PLIIz mode (page 74).
AFront speaker (Left)
BFront speaker (Right)
CCenter speaker
DSurround speaker (Left)
ESurround speaker (Right)
FSurround back speaker (Left)*
GSurround back speaker (Right)*
HFront high speaker (Left)*
IFront high speaker (Right)*
JSubwoofer
* You cannot use the surround back speakers and the
front high speakers simultaneously.
continued
19GB
STR-DN2010
4-182-049-11(1)
Connections
Connections
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Tips
• When you connect a 7.1 channel speaker system
with two surround back speakers, all angle A
should be the same.
• When you connect a 7.1 channel speaker system
with two front high speakers, place the front high
speakers
– at an angle between 22° to 45°.
– at least 3.3 feet (1 meter) directly above the front
speakers.
• When you connect a 6.1 channel speaker system,
place the surround back speaker behind the
listening position.
• Since the subwoofer does not emit highly
directional signals, you can place it wherever you
want.
20GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
2: Connecting the speakers
Connections
Before connecting cords, be sure to disconnect the AC power cord (mains lead).
Surround speaker
Center speaker
Right
B
Left
B
B
A
B
13/32"
(10 mm)
Right
Subwoofer**
Left
Surround back/Front high/
Bi-amplifier/Front B
speaker*
Right
Left
Front A speaker
A Monaural audio cord (not supplied)
B Speaker cord (not supplied)
continued
21GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
* Notes on the SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B terminals
connection.
– If you connect only one surround back speaker,
connect it to L of this terminals.
– If you are not using surround back speaker or
front high speakers, and you have an additional
front speaker system, connect the additional
front speaker system to this terminals.
Set “Sur Back Assign” to “SPEAKER B” in the
Speaker Settings menu (page 41).
You can select the front speaker system you
want using the SPEAKERS button on the
receiver (page 42).
– If you are not using surround back speaker or
front high speakers, you can connect the front
speakers to this terminals using bi-amplifier
connection (page 22).
Set “Sur Back Assign” to “BI-AMP” in the
Speaker Settings menu (page 41).
**When you connect a subwoofer with an auto
standby function, turn off the function when
watching movies. If the auto standby function is
set to on, it turns to standby mode automatically
based on the level of the input signal to a
subwoofer, then sound may not be output.
masterpage: Left
Bi-amplifier connection
If you are not using surround back speakers
and front high speakers, you can connect the
front speakers to the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals using a
bi-amplifier connection.
Front speaker
(Right)
Front speaker
(Left)
Hi
Hi
Lo
Lo
Notes
• Before connecting the AC power cord (mains
lead), make sure that metallic wires of the speaker
cords are not touching each other between the
SPEAKERS terminals.
• After you have install and connect your speaker, be
sure to select the speaker pattern from the Speaker
Settings menu (page 40).
Connect the jacks on the Lo (or Hi) side of the
front speakers to the SPEAKERS FRONT A
terminals, and connect the jacks on the Hi (or
Lo) side of the front speakers to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B terminals.
Make sure that metal fittings of Hi/Lo attached
to the speakers have been removed from the
speakers. Not doing so may cause a
malfunction of the receiver.
After you have made the bi-amplifier
connection, set “Sur Back Assign” to
“BI-AMP” in the Speaker Settings menu
(page 106).
22GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
3: Connecting the TV
TV with an HDMI jack
Audio signals
Audio/video
signals
A*
C
Video signals
**
B
D
or
ARC
E
Audio
signals
A
or
TV without an HDMI jack
A Optical digital cord (not supplied)
B HDMI cable (not supplied)
Recommended connection
Alternative connection
Sony recommends that you use an HDMIauthorized cable or Sony HDMI cable.
C Component video cord (not supplied)
D Video cord (not supplied)
E Audio cord (not supplied)
continued
23GB
STR-DN2010
4-182-049-11(1)
Connections
You can watch the selected input image when you connect the HDMI TV OUT or MONITOR OUT
jack to a TV. You can operate this receiver using a GUI (Graphical User Interface).
Before connecting cords, be sure to disconnect the AC power cord (mains lead).
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
* If you connect the receiver to the ARC
compatible TV’s HDMI jack via an HDMI cable,
you do not need to connect the TV to the receiver
with the optical digital cord.
**If you connect the receiver to the ARC
compatible TV, the TV sound will output from
the speakers connected to the receiver via the
HDMI TV OUT jack. In this case, set “Control
for HDMI” to “ON” in HDMI Settings menu
(page 90). If you want to select an audio signal
using other than an HDMI cable (e.g., via an
optical digital cord or an audio cord), switch the
audio input mode using INPUT MODE
(page 103).
masterpage: Left
Tips
• All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
• The receiver has a video conversion function. For
details, see “Function for conversion of video
signals” (page 33).
To enjoy TV multi channel
surround sound broadcasting
from the speakers connected to
the receiver
Connect the OPTICAL output jack of the TV
to the TV OPTICAL IN jack of the receiver. If
your TV is compatible with ARC function, use
HDMI connection.
Set the sound output jack of the TV to “Fixed”
if it can be switched between either “Fixed” or
“Variable”.
Notes
• Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. If the power supply
of the receiver is not turned on, neither video nor
audio signals will be transmitted.
• Connect image display components such as a TV
monitor or a projector to the HDMI TV OUT or
MONITOR OUT jack on the receiver. You may
not be able to record, even if you connect recording
components.
• Depending on the status of the connection between
the TV and the antenna (aerial), the image on the
TV screen may be distorted. In this case, place the
antenna (aerial) farther away from the receiver.
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
24GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
4a: Connecting the video components
Connections
Connecting components with
HDMI jacks
HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an
interface which transmits video and audio
signals in digital format.
By connecting Sony “BRAVIA” Synccompatible components using HDMI cables,
operations can be simplified. See ““BRAVIA”
Sync Features” (page 89).
HDMI features
• A digital audio signals transmitted by HDMI
can be output from the speakers connected to
the receiver. This signal supports Dolby
Digital, DTS, and Linear PCM. For details,
see “Digital audio formats supported by the
receiver” (page 76).
• The receiver can receive Multi Linear PCM
(up to 8 channels) with a sampling frequency
of 192 kHz or less with an HDMI
connection.
• Analog video signals input to the VIDEO
jack or COMPONENT VIDEO jacks can be
output as HDMI signals (page 33). Audio
signals are not output from an HDMI TV
OUT jack when the image is converted.
• This receiver supports High Bitrate Audio
(DTS-HD Master Audio, Dolby TrueHD),
Deep Color (Deep Colour), x.v.Color
(x.v.Colour) and 3D transmission.
• This receiver supports the Control for HDMI
function. For details, see ““BRAVIA” Sync
Features” (page 89).
continued
25GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Satellite tuner,
Cable TV tuner
DVD player,
DVD recorder
Audio/video
signals
Audio/video
signals
A
masterpage: Left
Blu-ray Disc player
Audio/video
signals
A
A
A
Audio/video
signals
“PlayStation 3”
A
Audio/video
signals
ARC
TV, etc.*
A HDMI cable (not supplied)
Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.
* For details on the audio connection of TV to the receiver, see page 23.
Notes
• HDMI 4 input has a better sound quality. When
you need a higher sound quality, connect your
component to the HDMI IN 4 (for AUDIO) jack
and select HDMI 4 as input.
• Be sure to change the initial setting of the HDMI
1–4 input button on the remote so that you can use
the button to control your components. For details,
see “Programming the remote” (page 130).
• You can also rename the HDMI input so that it can
be displayed on the TV screen and display. For
details, see “Naming the input (Name Input)”
(page 55).
26GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Notes on connecting cables
Notes on HDMI connections
• An audio signal input to the HDMI IN jack
is output from the SPEAKERS terminals,
HDMI TV OUT jack and PHONES jack. It
is not output from any other audio jacks.
• Video signals input to the HDMI IN jack can
only be output from the HDMI TV OUT
jack. The video input signals cannot be
output from the VIDEO OUT jacks or
MONITOR OUT jacks.
• The audio and video signals of HDMI input
are not output from the HDMI TV OUT jack
while the GUI menu is displayed.
• When you want to listen to the sound from
the TV speaker, set “Audio Out” to
“TV+AMP” in the HDMI Settings menu
(page 117). If you cannot play back multi
channel audio source, set to “AMP”.
However, the sound will not output from the
TV speaker.
• DSD signals of Super Audio CD are not
input and output.
• Be sure to turn on the receiver when the
video and audio signals of a playback
component are being output to a TV via the
receiver. If you set “Pass Through” to
“OFF”, video and audio signals will not be
transmitted when the power is turned off.
• Audio signals (format, sampling frequency,
bit length, etc.) transmitted from an HDMI
jack may be suppressed by the connected
component. Check the setup of the
connected component if the image is poor or
the sound does not come out of a component
connected via the HDMI cable.
• Sound may be interrupted when the
sampling frequency, the number of channels
or audio format of audio output signals from
the playback component is switched.
• When the connected component is not
compatible with copyright protection
technology (HDCP), the image and/or the
sound from the HDMI TV OUT jack may be
distorted or may not be output.
In this case, check the specification of the
connected component.
• You can enjoy High Bitrate Audio (DTS-HD
Master Audio, Dolby TrueHD), multi
channel Linear PCM only with an HDMI
connection.
• Set the image resolution of the playback
component to more than 720p/1080i to
enjoy High Bitrate Audio (DTS-HD Master
Audio, Dolby TrueHD).
• The image resolution of playback
component may need certain settings be
made before you can enjoy multi channel
Linear PCM. Refer to the operating
instructions of the playback component.
• To enjoy 3D images, connect 3D-compatible
TV and video components (Blu-ray Disc
player, Blu-ray Disc recorder, “PlayStation
3”, etc.) to the receiver using High Speed
HDMI cables, put on 3D glasses, and then
play back a 3D-compatible content.
• Depending on the TV or the video
component, 3D images may not be
displayed. Check the 3D image formats
supported by the receiver (page 146).
• Not every HDMI component supports all
functions that are defined by the specified
HDMI version. For example, components
that support HDMI, version 1.4, may not
support Audio Return Channel (ARC).
• Refer to the operating instructions of each
connected component for details.
27GB
STR-DN2010
4-182-049-11(1)
Connections
• Use a High Speed HDMI cable. If you use a
Standard HDMI cable, 1080p, Deep Color
(Deep Colour) or 3D images may not be
displayed properly.
• We do not recommend using an HDMI-DVI
conversion cable. When you connect an
HDMI-DVI conversion cable to a DVI-D
component, the sound and/or the image may
not be output. Connect other audio cords or
digital connecting cords, then set “Input
Assign” in the Input Option menu when the
sound is not output correctly.
• Before connecting cables, make sure to
disconnect the AC power cord (mains lead).
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Connecting components without
HDMI jacks
Connect your video components according to
the table below.
Component
Page
Blu-ray Disc player
29
DVD player
30
DVD recorder
30, 32
Satellite tuner,
Cable TV tuner
31
VCR
32
Camcorder, video game, etc.
32
If you want to connect several
digital components, but cannot
find an unused input
See “Enjoying the sound/images from other
inputs (Input Assign)” (page 104).
Converting video signals
This receiver is equipped with a function for
converting video signals. For details, see
“Function for conversion of video signals”
(page 33).
Notes
• Before connecting cords, be sure to disconnect the
AC power cord (mains lead).
• It is not necessary to connect all the cords. Connect
according to the availability of jacks on the
connected components.
• Be sure to turn on the receiver when the video and
audio signals of a playback component are being
output to a TV via the receiver. If the power supply
of the receiver is not turned on, neither video nor
audio signals will be transmitted.
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
28GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
To connect a Blu-ray Disc player
Video signals
or
A B
Connections
Blu-ray Disc player
Audio signals
or
or
C
D
A Component video cord (not supplied)
B Video cord (not supplied)
C Audio cord (not supplied)
D Optical digital cord (not supplied)
E Coaxial digital cord (not supplied)
E*
Recommended connection
Alternative connection
* When you connect a component equipped with an
COAXIAL jack, set “Input Assign” in the Input
Option menu (page 104).
Notes
• The initial setting of the COMPONENT VIDEO
IN 1 jacks are Blu-ray Disc player. If you want to
connect your Blu-ray Disc player to the
COMPONENT VIDEO IN 2 or IN 3 jacks, set
“Input Assign” in the Input Option menu
(page 104).
• To input multi channel digital audio from the
Blu-ray Disc player, set the digital audio output
setting on the Blu-ray Disc player. Refer to the
operating instructions supplied with the Blu-ray
Disc player.
continued
29GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
To connect a DVD player, DVD recorder
DVD player, DVD recorder
Video signals
Audio signals
or
A
B*
A Component video cord (not supplied)
B Optical digital cord (not supplied)
C Coaxial digital cord (not supplied)
C
Recommended connection
Alternative connection
* When you connect a component equipped with an
OPTICAL jack, set “Input Assign” in the Input
Option menu (page 104).
Notes
• The initial setting for the DVD input button is as
follows:
– RM-AAP055: DVD player
– RM-AAP056: DVD recorder
To control other components, be sure to change the
initial setting of the DVD input button on the
remote. For details, see “Programming the remote”
(page 130).
• You can also rename the DVD input so that it can
be displayed on the TV screen and display. For
details, see “Naming the input (Name Input)”
(page 55).
• The initial setting of the COMPONENT VIDEO
IN 2 jacks are DVD player or DVD recorder.
If you want to connect your DVD player or DVD
recorder to the COMPONENT VIDEO IN 1 or IN
3 jacks, set “Input Assign” in the Input Option
menu (page 104).
• To input multi channel digital audio from the DVD
player or DVD recorder, set the digital audio
output setting on the DVD player or DVD recorder.
Refer to the operating instructions supplied with
the DVD player or DVD recorder.
30GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
To connect a satellite tuner, cable TV tuner
Video signals
Audio signals
or
A
Connections
Satellite tuner, Cable TV tuner
or
B
C
A Component video cord (not supplied)
B Video cord (not supplied)
C Audio cord (not supplied)
D Optical digital cord (not supplied)
D
Recommended connection
Alternative connection
Note
The initial setting of the COMPONENT VIDEO IN
3 jacks are satellite tuner or cable TV tuner. If you
want to connect your satellite tuner or cable TV
tuner to the COMPONENT VIDEO IN 1 or IN 2
jacks, set “Input Assign” in the Input Option menu
(page 104).
continued
31GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
To connect components with analog video and audio jack
The following illustration shows how to connect a component which has analog jacks such as a
DVD recorder, VCR, etc.
DVD recorder, VCR
Audio signals
A
Video signals
B
(On the front panel)
Camcorder,
video game
C
A Audio cord (not supplied)
B Video cord (not supplied)
C Audio/video cord (not supplied)
Notes
• Be sure to change the initial setting of the VIDEO
1 input button on the remote so that you can use the
button to control your DVD recorder. For details,
see “Programming the remote” (page 130).
• You can also rename the VIDEO 1 input so that it
can be displayed on the TV screen and display. For
details, see “Naming the input (Name Input)”
(page 55).
32GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
Function for conversion of video signals
OUTPUT jack
INPUT jack
HDMI TV OUT
COMPONENT VIDEO
MONITOR OUT
MONITOR VIDEO OUT
HDMI IN*
a
–
–
VIDEO IN
a
a
a
COMPONENT VIDEO IN
a
a
a
a : Video signals are output.
– : Video signals are not output.
* HDMI video signals cannot be converted to component video signals and video signals.
As the initial setting, video signals input from the connected component are output as shown in the
table above. We recommend that you set the video conversion function to match the resolution of
the monitor you are using. For details, see “Video Settings menu” (page 116).
Notes on converting video
signals
• When video signals from a VCR, etc., are
converted on this receiver and then output to
your TV, depending on the status of the
video signal output, the image on the TV
screen may appear distorted horizontally or
no image may be output.
• The converted video signals are not output
from the VIDEO OUT jack.
• When you play back a VCR with an image
improvement circuit, such as TBC, the
images may be distorted or may not be
output. In this case, set the image
improvement circuit function to off.
• The resolution of the signals output to the
COMPONENT VIDEO MONITOR OUT
jacks is converted up to 1080i. The
resolution of the signals output to the HDMI
TV OUT jack is converted up to 1080p.
• COMPONENT VIDEO MONITOR OUT
jacks have restrictions on resolution when
the resolution of video signals protected by
copyright technology is converted.
Resolution of up to 480p/576p can be output
to the COMPONENT VIDEO MONITOR
OUT jacks. The HDMI TV OUT jack has no
restriction on resolution.
• Video signals for which the resolution has
been converted cannot be output from the
COMPONENT VIDEO MONITOR OUT
jacks or the HDMI TV OUT jack
simultaneously. The video signals are output
from the HDMI TV OUT jack when both are
connected.
• Set “Resolution” to “Auto” or “480i/576i” in
the Video Settings menu to output the video
signals from the MONITOR VIDEO OUT,
COMPONENT VIDEO MONITOR OUT
jacks when both are connected.
• Converted HDMI image output does not
support x.v.Color (x.v.Colour), Deep Color
(Deep Colour) and 3D image.
To connect a recording
component
When recording, connect the recording
component to the VIDEO OUT jacks of the
receiver. Connect cords for input and output
signals to the same type of jack, as VIDEO
OUT jacks do not have an up-conversion
function.
Note
Signals output from the HDMI TV OUT or
MONITOR OUT jacks may not be recorded
properly.
33GB
STR-DN2010
4-182-049-11(1)
Connections
The receiver is equipped with a function for converting video signals.
• Composite video signals can be output as HDMI video and component video signals
• Component video signals can be output as HDMI video and video signals.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
4b: Connecting the audio components
The following illustration shows how to connect a Super Audio CD player, CD player, CD recorder
and DIGITAL MEDIA PORT adapter. Before connecting cords, be sure to disconnect the AC
power cord (mains lead).
Super Audio
CD player,
CD player,
CD recorder
A
DIGITAL MEDIA
PORT adapter
A Audio cord (not supplied)
Notes on connecting DIGITAL
MEDIA PORT adapter
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is
turned on.
• Be sure to make DMPORT connections
firmly, insert the connector straight in.
• As the connector of the DIGITAL MEDIA
PORT adapter is fragile, be sure to handle
with care when placing or moving the
receiver.
• When connecting the DIGITAL MEDIA
PORT adapter, be sure the connector is
inserted with the arrow mark facing towards
the arrow mark on the DMPORT jack.
34GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
1
2
5: Connecting the
antennas (aerials)
Connect the supplied AM loop antenna
(aerial) and FM wire antenna (aerial).
Before connecting the antennas (aerials), be
sure to disconnect the AC power cord (mains
lead).
FM wire antenna (aerial) (supplied)
Press and hold both sides of the connector and
then pull out the connector.
AM loop antenna (aerial)
(supplied)
Notes
• To prevent noise pickup, keep the AM loop
antenna (aerial) away from the receiver and other
components.
• Be sure to fully extend the FM wire antenna
(aerial).
• After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
35GB
STR-DN2010
4-182-049-11(1)
Connections
To detach the DIGITAL MEDIA
PORT adapter from DMPORT
jack
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Notes
6: Inserting the wireless
transmitter/transceiver
To use the S-AIR function, you need to insert
the wireless transmitter (not supplied) into the
S-AIR main unit (this receiver) and the
wireless transceiver (not supplied) into the
S-AIR sub unit.
• Remove the screws on the slot cover pointed
with g and G marks. Do not remove other
screws.
• The slot cover is no longer necessary.
However, keep it after detaching.
2 Insert the wireless transmitter.
EZW-T100 slot
Notes
• Before inserting the wireless transmitter/
transceiver, be sure to disconnect the AC power
cord (mains lead).
• Do not touch the terminals of the wireless
transmitter/transceiver.
To insert the wireless
transmitter into the S-AIR main
unit
1 Remove the screws and detach the slot
cover.
Wireless transmitter
Notes
• Insert the wireless transmitter with the S-AIR
logo facing up.
• Insert the wireless transmitter so that the V
marks are aligned.
• Do not insert other than the wireless
transmitter into the EZW-T100 slot.
3 Use the screws that you removed from
step 1 to fasten the wireless
transmitter.
Slot cover
Note
Do not use other screws to fasten the wireless
transmitter.
To insert the wireless
transceiver into the S-AIR sub
unit
Refer to the operating instructions supplied
with the surround amplifier and S-AIR
receiver.
36GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Configuring your home network with DLNAcompliant devices.
If your computer is connected to the Internet,
you can connect this receiver to the Internet as
well, through the wired LAN connection.
Note
LAN cable (CAT5)
• We recommend that you use this type of
cable for a wired LAN.
Some flat-type LAN cables are easily
affected by noise. We recommend that you
use normal-type cables.
• If the receiver is used in an environment in
which there is power supply noise from
electric products or in a noisy network
environment, use a shielded-type LAN
cable.
The method used to connect your computer to the
Internet depends on the devices, your ISP, your
computer, and the router used.
System requirements
The following system environment is required
to use the network function of the receiver.
A Broadband line connection
A Broadband line connection to the Internet is
required in order to listen to Rhapsody® or
SHOUTcast and to use the software update
function of the receiver. Rhapsody is only
available in the U.S.
Modem
This is the device that is connected to the
broadband line to communicate with the
Internet. Some of these devices are integrated
with the router.
Router
• Use a router compatible with 100 Mbps or
greater transmission speeds to enjoy content
on your home network.
• We recommend that you use a router
equipped with the built-in DHCP (Dynamic
Host Configuration Protocol) server.
This function automatically assigns IP
addresses on the LAN.
37GB
STR-DN2010
4-182-049-11(1)
Connections
7: Connecting to the
network
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Configuration example
The following illustration is a configuration example of a home network with the receiver, a
computer.
We recommend that you use a wired connection.
LAN cable
(not supplied)
Internet
Modem
Computer
LAN cable
(not supplied)
Router
Notes
• An audio or video playback on the computer may
occasionally be interrupted when you use a
wireless connection.
• Connect a router to one among ports 1 to 4 of the
receiver using only one LAN cable. Do not connect
the same router to the receiver using more than one
LAN cable. It may cause a malfunction.
38GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
8: Connecting the AC
power cord (mains lead)
Notes
• Before connecting the AC power cord (mains
lead), make sure that metallic wires of the speaker
cords are not touching each other between the
SPEAKERS terminals.
• Connect the AC power cord (mains lead) firmly.
AC power cord (mains lead)
Preparing the Receiver
Initializing the receiver
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their initial settings.
Be sure to use the buttons on the receiver for
this operation.
?/1
MUSIC
To the wall outlet
MUTING
1
Press ?/1 to turn off the
receiver.
2
Hold down MUTING and MUSIC,
then press ?/1 to turn on the
receiver.
3
Release MUTING and MUSIC
after a few seconds.
After “CLEARING” appears on the
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
Note
It takes about 30 seconds for the memory to be
cleared completely. Do not turn the receiver off until
“CLEARED!” appears on the display.
continued
39GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
Connect the AC power cord (mains lead) to a
wall outlet.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
To reboot the receiver
If the buttons on the receiver or the remote do
not work due to a malfunction of the receiver,
reboot the receiver.
1 Press ?/1 to turn off the receiver.
2 Hold down ?/1 until the white indicator
flashes.
The receiver is rebooted.
Setting the speakers
Selecting the speaker pattern
Select the speaker pattern according to the
speaker system which you are using.
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
The Settings menu list appears on the TV
screen.
40GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
3
Press V/v repeatedly to select
“Speaker”, then press
.
1
Speaker Pattern
OFF
Test Tone
D.Range Comp :
4
AUTO
Press V/v repeatedly to select
“Speaker Pattern”, then press
.
Speaker Pattern
2
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“Speaker”, then press
.
4
Press V/v repeatedly to select
“Sur Back Assign”, then press
.
5
Press V/v repeatedly to select
the parameter you want, then
press
.
3/4.1
5
Press V/v repeatedly to select
the speaker pattern you want,
then press
.
6
Press RETURN/EXIT O.
• OFF
If you connect surround back or front
high speakers to the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals, select
“OFF”.
• BI-AMP
If you connect front speakers to the
SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B
terminals using a bi-amplifier
connection, select “BI-AMP”.
• SPEAKER B
If you connect an additional front
speaker system to the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals, select
“SPEAKER B”.
Setting the surround back
speakers
You can switch the usage of the speaker(s)
connected to the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals in accordance with the intended use.
Notes
• This setting is only available if the “Speaker
Pattern” is set to a setting without surround back
and front high speakers.
• Be sure to set “Sur Back Assign” before you
perform Auto Calibration.
Press V/v repeatedly to select
“ Settings”, then press
or
b.
6
Press RETURN/EXIT O.
41GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
Manual Setup
Crossover Freq
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Speaker Settings
Sur Back Assign :
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Selecting the front speaker
system
You can select the front speakers you want to
drive.
Be sure to use the buttons on the receiver for
this operation.
SPEAKERS
Press SPEAKERS repeatedly to
select the front speaker system
you want to drive.
You can confirm the selected speakers
terminals by checking the indicator on the
display.
When select the front speakers
connected to
Light up
The SPEAKERS FRONT A
terminals
SP A
The SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/
FRONT B terminals
SP B*
Both the SPEAKERS FRONT A and SP A B*
SPEAKERS SURROUND BACK/
FRONT HIGH/BI-AMP/FRONT B
terminals (parallel connection)
masterpage: Left
Calibrating the
appropriate speaker
settings automatically
(Auto Calibration)
This receiver is equipped with DCAC (Digital
Cinema Auto Calibration) function which
allows you to perform automatic calibration as
follows:
• Check the connection between each speaker
and the receiver.
• Adjust the speaker level.
• Measure the distance of each speaker from
your seating position.a)b)
• Measure the speaker size.a)
• Measure the speaker polarity.a)
• Measure the frequency characteristics.a)c)
a)
The measurement result is not utilized when
“A. DIRECT” is selected.
b) The measurement result is not utilized when
signals with a sampling frequency of more than
96 kHz are being received.
c) The measurement result is not utilized when
signals with a sampling frequency of more than
48 kHz are being received.
The DCAC is designed to obtain proper sound
balance in your room. However, you can
adjust the speaker levels manually according
to your preference. For details, see “Test
Tone” (page 111).
* To select “SP B” or “SP A B”, set “Sur Back
Assign” to “SPEAKER B” in the Speaker Settings
menu (page 41).
To turn off the speaker output
Press SPEAKERS repeatedly until the “SP A”
and “SP B” indicators on the display do not
light up. “SPK OFF” appears on the display.
Note
You cannot switch the front speaker system by
pressing SPEAKERS when the headphones are
connected.
42GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Before you perform Auto
Calibration
1: Setting up the Auto
Calibration
Optimizer microphone
Example of using surround back
speakers
1
Select the speaker pattern
(page 40).
If you connect front high speakers, select
the speaker pattern that has front high
speakers (5/x.x or 4/x.x) each time
you perform Auto Calibration.
Otherwise, the characteristics of the front
high speakers cannot be measured.
Notes
• During the measurement, the sound that comes out
of the speakers is very loud. The volume of the
sound cannot be adjusted. Pay attention to the
presence of children or to the effect on your
neighborhood.
• If the muting function has been activated before
you perform Auto Calibration, the muting function
will be set to off automatically.
• The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
Preparing the Receiver
Before you perform Auto Calibration, check
the following items.
• Set up and connect the speakers (page 19,
21).
• Connect only the supplied optimizer
microphone to the AUTO CAL MIC jack.
Do not connect other microphones to this
jack.
• Set “Sur Back Assign” to “BI-AMP” in the
Speaker Settings menu if you use
bi-amplifier connection (page 106).
• Set “Sur Back Assign” to “SPEAKER B” in
the Speaker Settings menu if you use
speakers front B connection (page 41).
• Pair the surround amplifier to S-AIR main
unit if you want to use surround amplifier.
• Make sure the speaker output is not set to
“SPK OFF” (page 42).
• Disconnect the headphones.
• Remove any obstacles in the path between
the optimizer microphone and the speakers
to avoid measurement errors.
• Make sure the environment is quiet to avoid
the effect of noise and get a more accurate
measurement.
• Select the seating position as position 1, 2 or
3 to save the Auto Calibration result
(page 108).
masterpage: Right
2
Connect the supplied optimizer
microphone to the AUTO CAL
MIC jack.
3
Set up the optimizer
microphone.
Place the optimizer microphone at your
seating position. Use a stool or tripod so
that the optimizer microphone remains at
the same height as your ears.
continued
43GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
On setting up the active
subwoofer
masterpage: Left
2: Performing Auto Calibration
• When a subwoofer is connected, turn on the
subwoofer and turn up the volume
beforehand. Turn the LEVEL to just before
the mid-point.
• If you connect a subwoofer with a crossover
frequency function, set the value to
maximum.
• If you connect a subwoofer with an auto
standby function, set it to off (deactivated).
?/1
Input
buttons
GUI
MODE
Note
Depending on the characteristics of the subwoofer
you are using, the setup distance value may be
further away from the actual position.
V/v/b,
MENU
MUTING/
1
MASTER
VOL +/–/
2 +/–
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
The Settings menu list appears on the TV
screen.
44GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Press V/v repeatedly to select
“Auto Calibration”, then press
.
4
Press V/v repeatedly to select
“Calibration Start”, then press
.
The screen on which you can select the
item to be measured appears.
Note
If an error code appears on the screen, see
“Message list after Auto Calibration
measurement” (page 48).
7
Press V/v repeatedly to select
the item you want, then press
.
Item and explanation
5
Press V/v repeatedly and
to
uncheck the items you do not
want to measure, then press b.
The confirmation screen, asking whether
you are ready to start measurement,
appears.
Retry
Performs the Auto Calibration again.
Save
Saves the measurement results and exits the
setting process (page 46).
Warning
Displays warning concerning the
measurement results. See “Message list after
Auto Calibration measurement” (page 48).
Phase*
Displays the phase of each speaker (in phase/
out of phase).
Distance
Displays the measurement result for speaker
distance.
6
Press
to select “Start”.
The measurement starts in five seconds.
The measurement process will take
approximately 30 seconds with a test
tone. Wait until the measurement process
completes.
When the measurement ends, a beep
sounds and the screen switches.
Level
Displays the measurement result for speaker
level.
Exit
Exits the setting process without saving the
measurement results.
To save the measurement results, follow
the steps in “3: Saving the measurement
results” (page 46).
If you want to check error code or
warning message, see “Message list after
Auto Calibration measurement”
(page 48).
continued
45GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
3
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
* When the speaker(s) is (are) out of the phase,
“Out” is displayed on the TV screen. The “+”
and “–” terminals of the speaker may be
connected the other way around.
However, depending on the speakers, “Out”
appears on the TV screen even though the
speakers are connected properly. This is
because of the speakers’ specifications. In
this case, you can continue to use the
receiver.
Tips
2
• Operations other than turning the receiver on or off
are deactivated during the measurement.
• You can change the unit of distance in “Distance
Unit” in the Speaker settings menu (page 113).
• Full Flat
Makes the measurement of frequency
from each speaker flat.
• Engineer
Sets the frequency to one that matches
that of the Sony listening room
standard.
• Front Reference
Adjusts the characteristics of all the
speakers to match the characteristics of
the front speaker.
• OFF
Sets the Auto Calibration equalizer
level to off.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press ?/1.
– Press the input buttons on the remote or
press the INPUT SELECTOR +/–
repeatedly on the receiver.
– Press MUTING (RM-AAP055 only) or
(RM-AAP056 only) on the remote. Press
MUTING on the receiver.
– Press SPEAKERS on the receiver.
– Change the volume level.
– Connect the headphones.
Press V/v repeatedly to select
the calibration type, then press
.
The measurement results are saved.
3
3: Saving the measurement
results
Disconnect the optimizer
microphone after you have
finished.
Note
To save the measurement results obtained in
“2: Performing Auto Calibration” (page 44),
proceed with the following steps.
If you have reposition your speaker, we recommend
that you perform Auto Calibration again to enjoy the
surround sound.
1
Tip
Press V/v to select “Save” in
step 7 in “2: Performing Auto
Calibration” (page 45), then
press
.
The selecting screen of the calibration
type appears.
The size of a speaker (“Large”/“Small”) is
determined by the low frequency characteristics.
The measurement results may vary, depending on
the position of the optimizer microphone and
speakers, and the shape of the room. It is
recommended that you follow the measurement
results. However, you can change those settings in
the Speaker Settings menu. Save the measurement
results first, then try to change the settings if you
want.
46GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
Checking the Auto Calibration
results
Preparing the Receiver
To check error code or warning message
obtained in “2: Performing Auto Calibration”
(page 44), proceed with the following steps.
Press V/v to select “Warning” in
step 7 in “2: Performing Auto
Calibration” (page 45) then press
.
If a warning message appears, check the
message and use the receiver without change.
Or if necessary, perform Auto Calibration
again.
When “Error Code” appears
Check the error and perform Auto Calibration
again.
1 Press
to select “Enter”.
“Retry?” appears on the TV screen.
2 Press B/b to select “Yes”, then press
.
3 Repeat steps 6 to 7 in “2: Performing
Auto Calibration” (page 45).
To save measurement results
that caused an error without
taking a remedy
1 Press V/v repeatedly to select “Save” in step
7 in “2: Performing Auto Calibration”
(page 45), then press .
2 Follow the steps in “3: Saving the
measurement results” (page 46) to save the
measurement results.
continued
47GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Message list after Auto Calibration measurement
Display and explanation
Error Code 31
The SPEAKERS is set to off. Set it to others and perform the Auto Calibration again.
Error Code 32
None of the speakers were detected. Make sure that the optimizer microphone is connected properly and
perform the measurement again.
If the optimizer microphone is connected properly but the error code appears, the optimizer microphone cable
may be damaged or improperly connected.
Error Code 33
• None of the front speakers are connected or only one front speaker is connected.
• The optimizer microphone is not connected.
• Either the surround left or surround right speaker is not connected.
• Surround back speakers or front high speakers are connected even though surround speakers are not
connected. Connect the surround speaker(s) to the SPEAKERS SURROUND terminals.
• The surround back speaker is connected only to the SPEAKERS SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B R terminals. When you connect only one surround back speaker, connect it to the
SPEAKERS SURROUND BACK/FRONT HIGH/BI-AMP/FRONT B L terminals.
• Either the front left high or front right high speaker is not connected.
Warning 40
The measurement has completed. However, the noise level is high. You may be able to perform the
measurement properly if you try it again, even though the measurement cannot be performed in all
environments. Try to perform the measurement in a quiet environment.
Warning 41
Warning 42
The input from the microphone is too big.
• The distance between the speaker and the microphone may be too close. Set them apart and perform the
measurement again.
Warning 43
The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the
measurement in a quiet environment.
No Warning
There is no warning information.
Tip
Depending on the position of the subwoofer, the
measurement results for polarity may vary.
However, there will be no problems even if you
continue to use the receiver with that value.
48GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Configuring the network
settings of the receiver
5
6
to select “Next”.
Press
to select “Connect
Automatically (DHCP)”.
7
Press
to select “Finish”.
To set the network settings
manually
See “To set the IP address manually”
(page 118) or “To set the Proxy server
manually” (page 119).
V/v/b,
MENU
1
Note
The wizard screen appears on the TV screen each
time you use the network function, until the network
function setup has been completed.
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
3
Press V/v repeatedly to select
“Network”, then press
.
4
Press V/v repeatedly to select
“Network Setup”, then press
.
“Start Network function Setup Wizard”
appears on the TV screen.
49GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
“Success! The receiver is now connected
to network.” appears on the TV screen
when you have succeeded in making a
connection.
If the failure screen is displayed, perform
the process referring to “Network Setup”
(page 118), after you have completed this
process.
The network settings for the receiver must be
set correctly to use the network functions of
the receiver.
You can make the required network settings
for the receiver by following the instructions
provided by an initial setup wizard.
The procedure used to set up the IP address
automatically (DHCP) is explained below.
In this case, the router that is connected to the
receiver or the Internet provider must support
DHCP.
Press
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Preparing a computer to
use as a server
A server is a device which delivers content
(music, photos, and videos) to a DLNA device
on a home network.
You can play back content stored on a
computer on a home network with this receiver
via that network after you have installed
application software* which has a DLNA
compliant server function.
* If you use a Windows 7-based computer, use
Windows Media Player 12 bundled with
Windows 7.
If you use a Windows XP or Windows Vista-based
computer, install the VAIO Media plus application
software supplied with the receiver. See “What
you can do with VAIO Media plus” below for
details. In addition, refer to the help files of VAIO
Media plus.
What you can do with VAIO
Media plus
VAIO Media plus is an application software
that enables you to quickly find content on
your home network, such as music, photos,
and videos, and view the content on the
computer through the home network.
By connecting other devices to VAIO Media
plus, you can also find and view the content on
the connected devices through the home
network. For example, you can enjoy photos
and music, stored on your computer, on your
TV and audio device or play a TV program,
recorded with a hard disk recorder, on your
computer.
If you use a VAIO computer, you can deliver
content saved on an external hard disk drive or
in Network-Attached Storage (NAS).
masterpage: Left
System Requirements
Operating System
Windows XP Home Edition/Professional/
Media Center Edition 2004/Media Center
Edition 2005 (SP3, 32 bit)
Windows Vista Home Basic/Home Premium/
Business/Ultimate (SP1, 32 bit/64 bit)
Computer
Windows XP
Windows Vista
Computer IBM PC/AT compatible
CPU
Intel Celeron M
processor
1.40 GHz or higher
(Intel Core 2 Duo
1.80 GHz or higher
is recommended.)
Memory 512 MB or more
(1 GB or more is
recommended.)
Intel Core Duo
1.33 GHz or higher
(Intel Core 2 Duo
2.26 GHz or higher
is recommended.)
1 GB or more
(2 GB or more is
recommended.)
Graphic
chip
Equipped with graphic chip by Intel,
NVIDIA or ATI.
DirectX 9.0c compatible video card
(DirectX 9.0c/128 MB compatible
video card and the latest driver are
recommended.)
Display
800 × 600 or higher resolution
HDD
500 MB or more is recommended.
Network 100Base-TX or higher
Sound
card
Direct Sound compatible sound card
Note
Sony does not guarantee trouble-free operation on
all computers that satisfy the system requirements.
Other software operating on background may affect
the operation of this software.
Note
If you use a computer other than a VAIO, you can
only deliver content saved on the internal disk drive
of that computer.
50GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Installing the VAIO Media plus
application software on a
computer
1
Turn on your computer and
login as an administrator.
2
Insert the supplied CD-ROM
into the CD-ROM drive of your
computer.
Referring to help files
For VAIO Media plus operations, refer to the
help files.
Click “
Settings” in the Home Menu
window, then select “ Help” to display help
files.
The installation launcher starts
automatically, then a Software Setup
window appears on the screen.
If installation launcher does not start
automatically, double-click
“SetupLauncher.exe” on the disc.
CD-ROM (VAIO Media
plus application
software) (supplied)
3
Install the VAIO Media plus
application software following
the instructions given in the
message on the screen.
51GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
When you use VAIO Media plus as server
software, install on your computer the VAIO
Media plus application software provided on
the CD-ROM supplied with the receiver by
following steps below.
If an older version of VAIO Media plus has
already been installed on your computer,
uninstall the following three programs using
“Programs and Features” (for Windows Vista)
or “Add or Remove Programs” (for Windows
XP) in Control Panel beforehand.
• VAIO Media plus
• VAIO Content Folder Watcher
• VAIO Content Folder Setting
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
3
Guide to on-screen
display operation
masterpage: Left
Press V/v repeatedly to select a
menu you want, then press
or b to enter the menu.
The menu item list appears on the TV
screen.
Input”.
Example: When you select “
You can display the menu of the receiver on
the TV screen and select the function you want
to use on the TV screen by pressing V/v/B/b
and
on the remote.
To display the menu of the receiver on the TV
screen, make sure that the receiver is in “GUI
MODE” following the steps in “To turn “GUI
MODE” on and off” (page 52).
GUI MODE
V/v/B/b,
RETURN/
EXIT O
Using the menu
2
Press V/v repeatedly to select
the menu item you want to
adjust, then press
to enter
the menu item.
5
Repeat steps 3 and 4 to select
the parameter you want.
TOOLS/
OPTIONS
MENU
1
4
To return to the previous screen
Press RETURN/EXIT O.
Switch the input of the TV so
that an image of the menu is
displayed.
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
To exit the menu
Press MENU.
To turn “GUI MODE” on and off
Press GUI MODE. “GUI ON” or “GUI OFF”
appears on the display, depending on the mode
selected.
52GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Overview of the main menus
Menu icon
Description
Selects the input source
component connected to the
receiver (page 54).
Music
Selects the music from the
server on the home network,
“My Library” or the audio
component connected to the
DIGITAL MEDIA PORT
adapter (page 56).
Photo
Video
Using the option menus
When you press TOOLS/OPTIONS, the
option menus for the selected main menu are
displayed. You can select a related function
without reselecting the menu.
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Selects the photos from the
server on the home network
or “My Library”.
Selects the images from the
server on the home network,
“My Library” or the audio
component connected to the
DIGITAL MEDIA PORT
adapter (page 56).
Rhapsody
Selects the Rhapsody radio
service (page 83). Rhapsody
is only available in the U.S.
SHOUTcast
Selects the SHOUTcast radio
service (page 86).
FM/AM/SR
Selects the built-in FM/AM
radio or satellite tuner
connected (page 61, 65).
Settings
You can adjust the settings of
the speakers, the surround
effect, equalizer, audio,
video and other inputs
connected to the HDMI jacks
(page 107).
2
Press V/v repeatedly to select a
menu you want, then press
or b to enter the menu.
The menu item list appears on the TV
screen.
Input”.
Example: when you select “
continued
53GB
STR-DN2010
4-182-049-11(1)
Preparing the Receiver
Input
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
3
Press TOOLS/OPTIONS while
the menu item list is displayed.
masterpage: Left
Basic Operations
The option menu appears.
Playback
?/1
Input
buttons
4
Press V/v repeatedly to select
the option menu item you want,
then press
or b.
5
Press V/v repeatedly to select
the parameter you want, then
press
.
SOUND
FIELD +/–
GUI MODE
V/v/B/b,
To exit the option menu
Press MENU.
TOOLS/
OPTIONS
MENU
MUTING/
1
MASTER
VOL +/–/
2 +/–
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“
Input”, then press
or b.
The menu item list appears on the TV
screen.
54GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
3
Press V/v repeatedly to select
the component you want, then
press
.
The menu screen disappears and the
playback screen of the external input
appears.
For details on the selected input and its
connected components, see
“Connections” (page 19).
Turn on the component and
start playback.
5
Press MASTER VOL +/–
(RM-AAP055 only) or 2 +/–
(RM-AAP056 only) to adjust the
volume.
You can also use MASTER VOLUME on
the receiver.
6
Press SOUND FIELD +/– to
enjoy the surround sound.
You can also use 2CH/A.DIRECT,
A.F.D., MOVIE or MUSIC button on the
receiver.
For details, see page 73.
Tips
• You can press INPUT SELECTOR +/– on the
receiver repeatedly or press input buttons on the
remote to select the component you want.
• You can adjust the volume differently depending
on the speed you turn the MASTER VOLUME on
the receiver.
To turn the volume up or down quickly: turn the
knob quickly.
To make fine adjustment: turn the knob slowly.
• You can adjust the volume differently depending
on the length of time you press and hold the
MASTER VOL +/– (RM-AAP055 only) or
2 +/– (RM-AAP056 only) on the remote.
To turn the volume up or down quickly: press and
hold the button.
To make a fine adjustment: press the button and
release it immediately.
To activate the muting function
Press MUTING (RM-AAP055 only) or
(RM-AAP056 only) on the remote.
You can also use MUTING on the receiver.
The muting function will be canceled when
you do the following.
• Press MUTING (RM-AAP055 only) or
(RM-AAP056 only) again.
• Increase the volume.
• Turn off the receiver.
• Perform Auto Calibration.
To avoid damaging your
speakers
Before you turn off the receiver, be sure to turn
down the volume level.
Naming the input (Name Input)
You can enter a name of up to 8 characters for
inputs and display it.
This is convenient for labeling the jacks with
the names of the connected components.
1
Press V/v repeatedly on the
“
Input” screen to select the
input you want.
2
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Name Input”, then press
.
4
Press V/v repeatedly to select a
character, then press b.
You can move the input position
backward and forward by pressing B/b.
5
Repeat step 4 to input a
character one by one, then
press
.
The name you entered is registered.
55GB
STR-DN2010
4-182-049-11(1)
Basic Operations
4
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Enjoying sound/images
from the components
connected to the DIGITAL
MEDIA PORT
The DIGITAL MEDIA PORT is for enjoying
sound/images from a portable audio source or
computer by connecting a DIGITAL MEDIA
PORT adapter.
The DIGITAL MEDIA PORT adapters are
available for purchase depending on the area.
For details on connecting the DIGITAL
MEDIA PORT adapter, see “4b: Connecting
the audio components” (page 34).
You can use the following Sony DIGITAL
MEDIA PORT adapters:
• TDM-BT1/BT10 Bluetooth™ Wireless
Audio Adapter
• TDM-NW10 DIGITAL MEDIA PORT
Adapter
• TDM-iP10/iP50 DIGITAL MEDIA PORT
Adapter
• TDM-MP10 DIGITAL MEDIA PORT
Adapter
The DIGITAL MEDIA PORT adapter is an
optional product.
Notes
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter to the DMPORT jack.
• Before disconnecting the DIGITAL MEDIA
PORT adapter, be sure to turn off the receiver.
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is turned
on.
• Depending on the type of DIGITAL MEDIA
PORT adapter, video output may not be possible.
• Do not connect a DIGITAL MEDIA PORT adapter
that uses a network function such as TDM-NC1
Wireless Network Audio Client to the receiver.
You can use the network function of the receiver
without using a DIGITAL MEDIA PORT adapter.
masterpage: Left
GUI MODE
V/v/b,
TOOLS/
OPTIONS
MENU
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ Music” or “
Video”, then
press
or b.
3
Press V/v repeatedly to select
“DMPORT” or a component
connected to the DIGITAL
MEDIA PORT adapter, then
press
.
The component connected to the
DIGITAL MEDIA PORT adapter is
recognized and “DMPORT” on the
screen will change to the respective
component’s name.
If the connected adapter cannot be
recognized, “DMPORT” is displayed on
the TV screen.
Name
Component that is
connected
DMPORT
A component other than one
of the following is connected.
iPod
The iPod model recognized is
connected.
Walkman
The Walkman recognized is
connected.
Bluetooth
The Bluetooth drive
recognized is connected.
Mobile Phone The Mobile Phone recognized
is connected.
56GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
4
5
Music
Select a track you want to play
back using the component
connected to the DIGITAL
MEDIA PORT adapter.
masterpage: Right
Playlists > Playlist > Track
Artists > Artist > Album > Track
Albums > Album > Track
Songs > Track
Genres > Genre > Artist > Album >
Track
Composers > Composer > Album >
Track
Audiobooks > Track
Press MASTER VOL +/–
(RM-AAP055 only) or 2 +/–
(RM-AAP056 only) to adjust the
volume.
Video
Movies > Content
TV Shows > Episode > Content
Music Videos > Artist > Content
Operating the TDM-iP50 using
the GUI menu of the receiver
1
Make sure that “System GUI” is
selected in step 4 in “Changing
the operation screen using the
DIGITAL MEDIA PORT”
(page 58).
2
Press V/v repeatedly to select
“ Music” or “
Video”, then
press
or b.
3
4
Video Podcasts > Episode > Content
5
Press MASTER VOL +/–
(RM-AAP055 only) or 2 +/–
(RM-AAP056 only) to adjust the
volume.
Selecting the playback mode
1
Press V/v repeatedly to select
the component connected to
the DIGITAL MEDIA PORT
adapter you want to play back,
then press
.
Play back the track you want to
listen to following the steps
outlined in “Operating the
TDM-iP50 using the GUI menu
of the receiver” (page 57).
2
Press TOOLS/OPTIONS.
The contents list appears.
3
Press V/v repeatedly to select
“Repeat”, “Shuffle” or
“Audiobook Speed”, then
press
.
4
Press V/v repeatedly to select
the mode you want, then press
.
The option menu appears.
Select track or content from the
contents list, then press
.
The following content lists are just
examples. They may vary depending on
the components connected to the receiver.
continued
57GB
STR-DN2010
4-182-049-11(1)
Basic Operations
You can also use MASTER VOLUME on
the receiver.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
x Repeat
masterpage: Left
Changing the operation screen
using the DIGITAL MEDIA PORT
Plays back one or all the tracks
repeatedly.
• Off
Deactivates the repeat play mode.
• One
Plays back one track repeatedly.
• All
Plays back all the tracks repeatedly.
You can change the operation screen using the
GUI menu. The DMPORT Control mode is
supported by the DIGITAL MEDIA PORT
adapters such as TDM-iP50. This mode is not
supported by other adapters.
x Shuffle
1
Select the DIGITAL MEDIA
PORT adapter you want on the
“ Music” or “
Video”
screen, then press
or b.
2
Press TOOLS/OPTIONS.
Plays back all the tracks in random order.
• Off
Deactivates the shuffle play mode.
• Songs
Plays back all the tracks in “Songs” in
random order.
• Albums
Plays back all the tracks on an album in
random order.
The option menu appears.
3
x Audiobook Speed
Selects the display speed of the
Audiobook.
• Low
Slows the display speed.
• Normal
Sets the display speed to standard.
• High
Increases the display speed.
DIGITAL MEDIA PORT message
list
Message and explanation
No Adapter
The adapter is not connected.
No Device
There is no device connected to the adapter.
Press V/v repeatedly to select
“DMPORT Control”, then press
.
If “DMPORT Control” is not displayed,
refer to the operating instructions
supplied with component for details on
operating that component.
4
Press V/v repeatedly to select
the mode you want, then press
.
• System GUI
The list of tracks will be displayed on
the GUI screen of the receiver. You can
select a track you want and play it back
on each GUI screen.
• Adapter GUI
The menu of the adapter will be
displayed on the TV screen.
• iPod
No Audio
No audio file was found.
Loading
The data is being read.
No Item
No item was found.
58GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
To operate the TDM-iP50 using
the adapter menu
Make sure that “Adapter GUI” is selected in
step 4 in “Changing the operation screen using
the DIGITAL MEDIA PORT” (page 58).
For details on operating the adapter using the
adapter GUI menu, refer to the operating
instructions supplied with the adapter you are
using.
masterpage: Right
Using the Sleep Timer
You can set the receiver to turn off
automatically at a specified time.
AMP
Basic Operations
To operate the TDM-iP50 using
the iPod menu
Make sure that “iPod” is selected in step 4 in
“Changing the operation screen using the
DIGITAL MEDIA PORT” (page 58).
For details on operating the iPod, refer to the
operating instructions supplied with the iPod.
SLEEP
Press AMP, then press SLEEP
repeatedly while the power is on.
“SLEEP” lights up on the display.
Each time you press SLEEP, the display
changes cyclically as follows:
0:30:00 t 1:00:00 t 1:30:00 t 2:00:00
t OFF
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time appears
on the display. If you press SLEEP again, the Sleep
Timer will be canceled.
59GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Recording using the
receiver
You can record from a video/audio component
using the receiver. Refer to the operating
instructions supplied with your recording
component.
3
masterpage: Left
Prepare the recording
component.
Insert a blank CD-R into the CD recorder
and adjust the recording level.
4
Start recording on the
recording component, then
start playback on the playback
component.
Note
Sound adjustments do not affect the signal output
from the SA-CD/CD/CD-R AUDIO OUT jacks.
Input
buttons
Recording with a video
component
1
Press one of the input buttons
to select the playback
component.
You can also use INPUT SELECTOR +/–
on the receiver.
GUI MODE
V/v/B/b,
2
Prepare the playback
component for playing.
For example, insert the video tape you
want to copy into the VCR.
3
Insert a blank video tape, etc. into the
recording component (connected to
VIDEO 1 OUT jacks) for recording.
Recording onto a CD-R
You can record onto a CD-R using the
receiver. Refer to the operating instructions
supplied with your CD recorder.
1
Press one of the input buttons
to select the playback
component.
Prepare the recording
component.
4
Start recording on the
recording component, then
start playback on the playback
component.
You can also use INPUT SELECTOR +/–
on the receiver.
2
Prepare the playback
component for playing.
For example, tune to the radio station you
want to record (page 61).
60GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
Notes
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to
record from the source.
• Only analog input signals are output from the
analog output jack (for recording).
• HDMI sound cannot be recorded.
• While only composite video signals are being
recorded, the auto standby function of the receiver
may start up and interrupt the recording. In this
case, set “Auto Standby” to “OFF” (page 121).
Tuner Operations
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation, be
sure you have connected the FM and AM
antennas (aerials) to the receiver (page 35).
Tip
The tuning scale for direct tuning is shown below.
FM
AM
USA
100 kHz
10 kHz*
Europe
50 kHz
9 kHz
* The AM tuning scale can be changed (page 63).
SHIFT
Numeric
buttons
GUI MODE
V/v/b,
TOOLS/
OPTIONS
MENU
61GB
STR-DN2010
4-182-049-11(1)
Tuner Operations
Area
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Tuning into a station
automatically (Auto Tuning)
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ FM FM” or “ AM AM”, then press
or b.
Tuning into a station directly
(Direct Tuning)
You can enter the frequency of a station
directly by using the numeric buttons.
1
Press V/v repeatedly to select
“Auto Tuning”, then press
.
4
Press V/v.
Press V to scan from low to high, press v
to scan from high to low.
The receiver stops scanning whenever a
station is received.
2
Press V/v repeatedly to select
“ FM FM” or “ AM AM”, then press
or b.
The FM or AM menu list appears on the
TV screen.
3
Press V/v repeatedly to select
“Direct Tuning”, then press
.
4
Press SHIFT, then press
numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 (b 0*)
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
In case of poor FM stereo
reception
1 Tune in the station you want to listen to
using Auto Tuning, Direct Tuning
(page 62), or select the preset station you
want (page 63).
2 Press TOOLS/OPTIONS.
3 Press V/v repeatedly to select “FM Mode”,
then press
or b.
4 Press V/v repeatedly to select “Mono”, then
press .
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
The FM or AM menu list appears on the
TV screen.
3
masterpage: Left
* Press 0 for European model only.
Tip
If you have tuned in an AM station, adjust
the direction of the AM loop antenna
(aerial) for optimum reception.
5
Press
.
If you cannot tune in a station
“– – – .– – MHz” appears and then the screen
returns to the current frequency.
Make sure you have entered the right
frequency. If not, repeat step 4. If you still
cannot tune in a station, the frequency is not
used in your area.
62GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Changing the AM tuning scale
(USA model only)
You can change the AM tuning scale to either
9 kHz or 10 kHz using the buttons on the
receiver.
?/1
masterpage: Right
Presetting FM/AM radio
stations
(Preset Tuning)
You can preset up to 30 FM and 30 AM
stations. Then you can easily tune in the
stations you often listen to.
V/v/B/b,
1
Press ?/1 to turn off the
receiver.
2
While holding down DISPLAY,
press ?/1 on the receiver.
3
Change the current AM tuning
scale to 9 kHz (or 10 kHz).
1
In case of poor FM stereo reception,
switch the FM reception mode (page 62).
To reset the scale to 10 kHz (or 9 kHz),
repeat the procedure above.
Note
All preset stations will be erased when you change
the tuning scale.
Tune in the station that you
want to preset using Auto
Tuning (page 62) or Direct
Tuning (page 62).
2
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Memory”, then press
or b.
4
Press V/v repeatedly to select a
preset number, then press
.
The station is stored as the selected preset
number.
5
Repeat steps 1 to 4 to preset
another station.
You can store station as follows:
• AM band: AM 1 to AM 30
• FM band: FM 1 to FM 30
63GB
STR-DN2010
4-182-049-11(1)
Tuner Operations
TOOLS/
OPTIONS
DISPLAY
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Tuning to preset stations
1
Select “ FM FM” or “ AM AM” from
the menu, then press
or b.
2
Press V/v repeatedly to select
the preset station you want.
Preset numbers from 1 to 30 are available.
Naming preset stations (Name
Input)
1
2
On “ FM FM” or “ AM AM” screen,
press V/v repeatedly to select
the preset number on which
you have stored the station and
which you want to name.
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Name Input”, then press
or
b.
4
Press V/v repeatedly to select a
character, then press b.
You can move the input position
backward and forward by pressing B/b.
5
Repeat step 4 to input a
character one by one, then
press
.
The name you entered is registered.
masterpage: Left
Receiving RDS
broadcasts
(European model only)
This receiver allows you to use Radio Data
System (RDS), which enables radio stations to
send additional information along with the
regular program signal. This receiver offers
convenient RDS features, such as Program
Service name display. RDS is available only
for FM stations.*
* Not all FM stations provide RDS service, nor do
they provide the same type of services. If you are
not familiar with the RDS services in your area,
check with your local radio stations for details.
Simply select a station on the FM
band using Direct Tuning (page 62),
Auto Tuning (page 62), or Preset
Tuning (page 63).
When you tune in a station that provides RDS
services, “RDS” lights up and the Program
Service name* appears on the TV screen and
the display.
* If an RDS broadcast is not received, a Program
Service name will not appear on the display.
Notes
• RDS may not work properly if the station you
tuned to is not transmitting the RDS signal
properly or if the signal strength is weak.
• Some letters that can be displayed on the TV screen
cannot be displayed on the display.
Tip
When a Program Service name is displayed, you can
check the frequency by pressing DISPLAY
repeatedly (page 127).
64GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Listening to Satellite
Radio
(USA model only)
To listen to Satellite Radio, you’ll need to
connect a SIRIUS Satellite Radio tuner (sold
separately) to your Sirius-Ready receiver.
SIRIUS Satellite Radio is available to
residents of the US (except Alaska and
Hawaii) and Canada.
masterpage: Right
SIRIUS and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All other marks and logos are the
property of their respective owners. All rights
reserved. SIRIUS subscription sold separately.
Taxes and a one-time activation fee may apply.
SIRIUS tuner required (sold separately) to receive
the SIRIUS service. All programming and fees
subject to change. It is prohibited to copy,
decompile, disassemble, reverse engineer, hack,
manipulate or otherwise make available any
technology or software incorporated in receivers
compatible with the SIRIUS Satellite Radio System.
Service not available in Alaska or Hawaii.
Tuner Operations
Satellite Radio delivers a variety of
commercial-free music from categories
ranging from Pop, Rock, Country, R&B,
Dance, Jazz, Classical and many more plus
coverage of all the top professional and
college sports including play by play games
from select leagues and teams. Additional
programming includes expert sports talk,
uncensored entertainment, comedy, family
programming, local traffic and weather and
news from your most trusted sources.
Once you’ve purchased a SIRIUS tuner you’ll
need to activate it and subscribe to begin
enjoying the service. Easy to follow
installation and setup instructions are provided
with the SIRIUS tuner. There are a variety of
programming packages available, including
the option of adding “The Best of XM”
programming to the SIRIUS service. The
“Best of XM” service is not available to
SIRIUS Canada subscribers at this time.
Please check with SIRIUS Canada for any
updates using the numbers and web address
below.
Family friendly packages are also available to
restrict channels featuring content that may be
inappropriate for children.
To subscribe to SIRIUS, U.S. and Canadian
customers can call 1-888-539-SIRI (1-888539-7474) or visit sirius.com (US) or
siriuscanada.ca (Canada).
65GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Connecting a satellite
radio tuner
masterpage: Left
Preparing to listen to a
satellite radio
Connect the SiriusConnect Home tuner. When
you use the SiriusConnect Home tuner with
this receiver, be sure to connect the AC power
adaptor supplied with the tuner to a wall outlet.
GUI MODE
V/v/b,
SIRIUS jack
TOOLS/
OPTIONS
MENU
Checking the ID number
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Note
Keep the SiriusConnect Home tuner, antenna, and
AC power adaptor away from the speaker cords and
the power cord to avoid picking up noise.
2
Press V/v repeatedly to select
“ SR SR”, then press
or b.
3
Press V/v repeatedly to select
“ALL”, then press
.
When the “Preset Mode” screen is
displayed, change the tuning mode to
“Category Mode”, then select “ALL”.
Press TOOLS/OPTIONS, then select
“Category Mode”.
4
Press V/v repeatedly to select
“Sirius ID”, then press
.
5
Check the SIRIUS ID on the TV
screen and write it in the space
provided here.
SIRIUS ID:_________________________
You can also check the SIRIUS ID using
the display on the receiver.
66GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Checking receiving conditions
(Antenna Aiming)
1
2
Select “ SR SR” from the menu,
then press
or b.
masterpage: Right
Selecting a channel of the
satellite radio
SHIFT
Press TOOLS/OPTIONS.
Numeric
buttons
The option menu appears.
Press V/v repeatedly to select
“Antenna Aiming”, then press
.
4
While checking the quality of
the reception, adjust the
direction of the antenna to
obtain the best reception.
GUI MODE
V/v/b,
To exit the menu
TOOLS/
OPTIONS
Press MENU.
MENU
Selecting a channel by category
(Category Mode)
You can select a channel from one category or
all the categories.
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ SR SR”, then press
or b.
continued
67GB
STR-DN2010
4-182-049-11(1)
Tuner Operations
3
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
3
Press V/v repeatedly to select
the category, then press
.
Selecting a channel by inputting
the channel number directly
(Direct Tuning)
• ALL: You can select a channel from all
the categories.
• (category name): You can select a
channel from one category.
You can enter the channel number directly by
using the numeric buttons.
Note
1
When the “Preset Mode” screen is displayed,
press TOOLS/OPTIONS, then press V/v
repeatedly to select “Category Mode”.
4
masterpage: Left
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Press V/v repeatedly to select
the channel, then press
.
The selected channel is being received.
The channel information is displayed on
the TV screen.
Note
When you select a channel in the “Category Mode”,
the channel you selected may not be the one in the
category you want. This is because one channel may
belong to more than one category.
Press GUI MODE.
2
Press V/v repeatedly to select
“ SR SR”, then press
or b.
3
Press TOOLS/OPTIONS.
The option menu appears.
4
Press V/v repeatedly to select
“Direct Tuning”, then press
.
5
Press SHIFT, then press the
numeric buttons to enter the
channel number.
6
Press
.
The selected channel is tuned in.
68GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Presetting satellite radio
channels
You can select the channels you want directly
by presetting them using the preset numbers.
You can preset up to 30 SIRIUS Satellite
Radio channels.
masterpage: Right
Selecting preset channels
1
Select “ SR SR” from the menu,
then press
or b.
2
Press V/v repeatedly to select
the preset number from the
preset list, then press
.
You can select stored preset channels
from 1 to 30.
Notes
V/v/b,
1
Select a channel you want to
preset using Category Mode
(page 67) or Direct Tuning
(page 68).
2
Press TOOLS/OPTIONS.
The option menu appears.
3
Press V/v repeatedly to select
“Memory”, then press
.
The preset number selection screen
appears.
4
Press V/v repeatedly to select
the preset number you want to
use as the preset channel, then
press
.
Preset channels from 1 to 30 are available,
and a default channel is preset for all the
preset channels when you purchase the
receiver.
The selected channel is registered as the
preset channel you selected in step 1.
5
Repeat steps 1 to 4 to preset
another channel.
69GB
STR-DN2010
4-182-049-11(1)
Tuner Operations
TOOLS/
OPTIONS
• The channel information you have preset may be
changed if Sirius XM Radio Inc. change its channel
programming.
• When the “Category Mode” screen is displayed,
press TOOLS/OPTIONS, then press V/v
repeatedly to select “Preset Mode”.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
Restricting access to
specific channels
4
You can restrict access to certain channels
using your own lock code. The lock code is set
to “0000” as the default.
Change the lock code before you use this
function for the first time. See “To change the
lock code (Lock Code)” (page 70).
SHIFT
Numeric
buttons
Press V/v repeatedly to select
“ON”, then press
.
“Enter your 4-digit lock code.” appears.
5
(Parental Lock)
masterpage: Left
Press SHIFT, then press the
numeric buttons to enter your
4-digit lock code.
“The channel has been locked.” appears
and the Parental Lock is set.
To delete the numbers you have entered,
go back to step 2 by pressing RETURN/
EXIT O, and then repeat the procedure
above from step 2.
To change the lock code (Lock
Code)
1 Select a channel you want to change
the lock code using Category Mode
(page 67) or Direct Tuning (page 68).
2 Press TOOLS/OPTIONS.
The option menu appears.
3 Press V/v repeatedly to select “Lock
V/v/b,
RETURN/
EXIT O
TOOLS/
OPTIONS
Code”, then press
.
“Enter your 4-digit lock code.” appears.
4 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
“Enter a new lock code.” appears.
5 Enter a new 4-digit lock code using the
1
2
Select a channel you want to
lock using Category Mode
(page 67) or Direct Tuning
(page 68).
Press TOOLS/OPTIONS.
numeric buttons.
“To confirm, enter your new lock code
again.” appears.
6 Reenter the new lock code with the
numeric buttons.
“The lock code has been changed.”
appears.
The option menu appears.
3
Press V/v repeatedly to select
“Parental Lock”, then press
or b.
70GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Right
To listen to the locked channels
1 Select a locked channel you want to
listen to using Direct Tuning (page 68).
“Enter your 4-digit lock code.” appears.
2 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
The channel is tuned in.
To cancel the Parental Lock
1 Select a channel you want to unlock
using Direct Tuning (page 68).
Tuner Operations
2 Press TOOLS/OPTIONS.
The option menu appears.
3 Press V/v repeatedly to select
“Parental Lock”, then press
or b.
4 Press V/v repeatedly to select “OFF”,
then press
.
“Enter your 4-digit lock code.” appears.
5 Press SHIFT, then press the numeric
buttons to enter your 4-digit lock code.
“The channel has been unlocked.” appears
and the channel is unlocked.
Notes
• When you select a channel using Category Mode,
locked channels are skipped.
• When the receiver is reset to the initial settings, the
lock code returns to the default (0000), but the
Parental Lock settings are not removed.
• You cannot preset locked channels. If you set the
Parental Lock for a preset channel, the preset
information for that channel returns to the default.
• You cannot set the Parental Lock for channel 0 and
channel 184.
• You can set only one lock code on the receiver.
You cannot set individual lock codes for each
channel.
continued
71GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB04GET_STR-DN2010-CEL.fm
masterpage: Left
Satellite radio message list
Message
appears on
TV screen
[Display]
Explanation
Remedies
Antenna Error
[ANTENNA
ERROR]
The antenna is not connected
properly.
Check the connection between the SiriusConnect
Home tuner and the antenna.
Acquiring Signal
[ACQUIRING]
The receiving condition is not
good.
Try moving the antenna to another location.
For details about the antenna location, refer to the
operating instructions supplied with the SiriusConnect
Home tuner.
Call 888-539-SIRI You have not subscribed for the
[CALL 888-539- selected channel.
SIRI]
—
Check Sirius Tuner The SiriusConnect Home tuner is Check all the connections, and then turn the system on
[SR TUNER]
not connected properly.
again. Also make sure if the AC adaptor supplied with
the SiriusConnect Home tuner is connected to a wall
socket.
Invalid Channel
[INVALID
CHANNEL]
You have entered an invalid
channel number.
The channel to be tuned-in is void due to the change
by the broadcast service, or the receiving condition is
not good.
Locked Channel
[LOCKED CH]
The selected channel is locked.
—
Sub Updated
[SUB UPDT]
The subscription information has
been updated.
—
Updating
[UPDATING]
Channel information is being
updated.
—
FW Updating
[FW UPDT]
The SiriusConnect Home tuner
firmware is being updated.
—
––––
There is no text information in the This is not an error. The text information may not be
channel.
displayed depending on the system condition, for
example, right after the system has received a channel.
72GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Note
Enjoying Surround Sound
Selecting the sound field
This receiver can create multi channel
surround sound. You can select one of the
optimized sound fields from the receiver’s
preprogrammed sound fields.
.
SOUND
FIELD +/–
You cannot select “A. DIRECT” in the following
cases.
– When you play back content on devices on a home
network.
– When you select DVD and HDMI 1- 4 as input.
Auto Format Direct (A.F.D.)
mode
The Auto Format Direct (A.F.D.) mode allows
you to listen to high fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
x A.F.D. AUTO (A.F.D. Auto)
You can also use 2CH/A.DIRECT, A.F.D.,
MOVIE or MUSIC on the receiver.
2 channel sound mode
You can switch the output sound to 2 channel
sound regardless of the recording formats of
the software you are using, the playback
component connected, or the sound field
settings of the receiver.
Presets the sound as it was recorded/encoded
without adding any surround effects.
x MULTI ST. (A.F.D. Multi Stereo)
Outputs 2 channel left/right signals from all
speakers.
Movie mode
You can take advantage of surround sound
simply by selecting one of the receiver’s preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
into your home.
x 2CH ST. (2ch Stereo)
The receiver outputs the sound from the front
left/right speakers only. There is no sound
from the subwoofer.
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
x C.ST.EX A (Cinema Studio EX A
DCS )
x A. DIRECT (2ch Analog Direct)
x C.ST.EX B (Cinema Studio EX B
DCS )
You can switch the audio of the selected input
to 2 channel analog input. This function
enables you to enjoy high quality analog
sources.
When using this function, only the volume and
front speaker level can be adjusted.
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Cary Grant
Theater” cinema production studio. This is a
standard mode, great for watching almost any
type of movie.
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Kim Novak
Theater” cinema production studio. This mode
is ideal for watching science-fiction or action
movies with lots of sound effects.
continued
73GB
STR-DN2010
4-182-049-11(1)
Enjoying Surround Sound
Press SOUND FIELD +/– repeatedly
to select the sound field you want.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
x C.ST.EX C (Cinema Studio EX C
DCS )
Reproduces the sound characteristics of the
Sony Pictures Entertainment scoring stage.
This mode is ideal for watching musicals or
films where orchestra music is featured in the
soundtrack.
masterpage: Left
x HALL (Hall)
Reproduces the acoustics of a classical concert
hall.
x JAZZ (Jazz Club)
Reproduces the acoustics of a jazz club.
x CONCERT (Live Concert)
x V.MULTI DIM. (V.Multi
Dimension DCS )
Reproduces the acoustics of a 300-seat live
house.
Creates many virtual speakers from a single
pair of actual surround speakers.
x STADIUM (Stadium)
x PLII Movie
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition, this
mode can reproduce sound in 5.1 channel for
watching videos of overdubbed or old movies.
x PLIIx Movie
Performs Dolby Pro Logic IIx Movie mode
decoding. This setting expands Dolby Pro
Logic II Movie or Dolby Digital 5.1 to discrete
7.1 movie channels.
x PLIIz (PLIIz Height)
Performs Dolby Pro Logic IIz mode decoding.
This setting increases flexibility to expand a
5.1 to a 7.1 channel system. Its vertical
component gives a dimension of presence and
depth.
x Neo:6 CIN (Neo:6 Cinema)
Performs DTS Neo:6 Cinema mode decoding.
A source recorded in 2 channel format is
decoded into 7 channels.
Music mode
You can take advantage of surround sound
simply by selecting one of the receiver’s
preprogrammed sound fields. They bring the
exciting and powerful sound of concert halls
into your home.
Reproduces the feeling of a large open-air
stadium.
x SPORTS (Sports)
Reproduces the feeling of sports broadcasting.
x PORTABLE (Portable Audio)
Reproduces a clear enhanced sound image
from your portable audio device. This mode is
ideal for MP3 and other compressed music.
x PLII Music
Perform Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
x PLIIx Music
Performs Dolby Pro Logic IIx Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
x PLIIz (PLIIz Height)
Performs Dolby Pro Logic IIz mode decoding.
This setting increases flexibility to expand a
5.1 to a 7.1 channel system. Its vertical
component gives a dimension of presence and
depth.
x Neo:6 MUS (Neo:6 Music)
Performs DTS Neo:6 Music mode decoding.
A source recorded in 2 channel format is
decoded into 7 channels. This setting is ideal
for normal stereo sources such as CDs.
74GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
When headphones are
connected
You can only select this sound field if the
headphones are connected to the receiver.
x HP 2CH (Headphone (2ch))
This mode is selected automatically if you use
headphones (except “A. DIRECT”). Standard
2 channel stereo sources completely bypass
the sound field processing and multi channel
surround formats are downmixed to 2
channels except LFE signals.
Note
When headphones are connected to the S-AIR
surround amplifier, the sound field is automatically
set to “HP 2CH”.
masterpage: Right
• When one of the sound fields for music is selected,
no sound is output from the subwoofer if all the
speakers are set to “Large” in the Speaker Settings
menu. However, the sound will be output from the
subwoofer if
– the digital input signal contains LFE signals.
– the front or surround speakers are set to “Small”.
– the sound field for movie is selected.
– “PORTABLE” is selected.
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
• If you set up the sound field during DTS 96/24
signal reception, the signal will be played back
only at 48 kHz.
• If there is any noise present, the noise may be
different depending on the sound field you select.
This mode is selected automatically if you use
headphones when “A. DIRECT” is selected.
Outputs the analog signals without processing
by the equalizer, sound field, etc.
Notes on sound fields
• Depending on the speaker pattern settings, some
sound fields may not be available.
• You cannot select PLIIx and PLIIz at the same
time.
– PLIIx is available only when the speaker pattern
is set to a setting with surround back speaker(s).
– PLIIz is available only when the speaker pattern
is set to a setting with front high speakers.
• The sound fields for music and movie do not work
in the following cases.
– Signals with a sampling frequency of more than
48 kHz are being received.
– Signals with more than 5.1 channel are being
received (except PLIIz).
• “PLII movie”, “PLIIx Movie”, “PLII Music”,
“PLIIx Music”, “PLIIz”, “Neo:6 CIN” and
“Neo:6 MUS” also do not work when the speaker
pattern is set to 2/0 or 2/0.1.
• You can identify the encoding format of DVD
software, etc., by looking at the logo on the
package.
• Dolby Pro Logic IIx and Dolby Pro Logic IIz
decoding are effective when multi channel signals
are input.
• Sound fields with DCS marks use DCS
technology.
To turn off the surround effect
for movie/music
Press SOUND FIELD +/– repeatedly to select
“2CH ST.” or “A.F.D. AUTO”.
You can also press 2CH/A.DIRECT
repeatedly on the receiver to select “2CH ST.”
or press A.F.D. repeatedly on the receiver to
select “A.F.D. AUTO”.
75GB
STR-DN2010
4-182-049-11(1)
Enjoying Surround Sound
Tips
x HP DIRECT (Headphone (Direct))
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Digital audio formats supported by the receiver
Digital audio formats that this receiver can decode depend on digital audio input jacks for the
components connected. This receiver supports the following audio formats.
Audio format
Maximum number
of channels
Connection of the playback component and
the receiver
COAXIAL/OPTICAL
HDMI
Dolby Digital
5.1
a
a
Dolby Digital EX
6.1
a
a
a)
7.1
×
a
Dolby TrueHDa)
7.1
×
a
DTS
5.1
a
a
DTS-ES
6.1
a
a
DTS 96/24
5.1
a
a
DTS-HD
High Resolution Audioa)
7.1
×
a
DTS-HD
Master Audioa)b)
7.1
×
a
Multi channel Linear PCMa)
7.1
×
a
Dolby Digital Plus
a) Audio signals are output in another format if the playback component does not correspond to the format. For
b)
details, refer to the operating instructions of the playback component.
Signals with a sampling frequency of more than 96 kHz are played back at 96 kHz or 88.2 kHz.
76GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Enjoying the surround
effect at low volume
levels
(NIGHT MODE)
masterpage: Right
Resetting sound fields to
the initial settings
Be sure to use the buttons on the receiver for
this operation.
?/1
This function allows you to retain a theater like
environment at low volume levels. This
function can be used with other sound fields.
When watching a movie late at night, you will
be able to hear the dialog clearly even at a low
volume level.
NIGHT
MODE
The NIGHT MODE function is activated. The
NIGHT MODE is set to on and off as you
press NIGHT MODE.
Note
1
Press ?/1 to turn off the
receiver.
2
While holding down MUSIC,
press ?/1.
“S.F. CLEAR” appears on the display and
all sound fields are reset to their initial
setting.
This function does not work in the following cases.
– “A. DIRECT” is being used.
– Signals with a sampling frequency of more than
48 kHz are being received.
Tip
While this function is on, the Bass, Treble, and
Effect Levels increase, and “D.Range Comp” is
automatically set to “MAX”.
77GB
STR-DN2010
4-182-049-11(1)
Enjoying Surround Sound
Press NIGHT MODE to select
“NIGHT ON”.
MUSIC
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Using Network Features
About the network functions of the receiver
• You can enjoy content (music, photos, and videos) which have been stored on a DLNA-compliant
device (DLNA CERTIFIED™ Products) that has an authorized DLNA logo displayed on the
device (page 78).
• You can use the receiver as a device equivalent to a UPnP media renderer on your home network.
• With an Internet connection, you can listen to Rhapsody and SHOUTcast (page 83, 86) and
upgrade the software of the receiver. Rhapsody is only available in the U.S.
• You can change the settings of the receiver using a computer on your home network (page 88).
About DLNA
DLNA (Digital Living Network Alliance) is a standard organization made up of manufacturers of
various products, such as computers, AV components, and mobile computing devices which
exchange content (music, photos, and videos). DLNA decides upon standards and publishes an
authorized logo to be displayed on devices which support DLNA standards.
Enjoying content stored on the server
A server is a device which delivers content (music, photos, and videos) to a DLNA device on a
home network.
You can play back music, photos, and videos stored on the server using the receiver.
Computer
This receiver
78GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
To search the server
GUI MODE
You can search the server if the server list does
not appear on the TV screen.
V/v/B/b,
1 Select “
“
TOOLS/
OPTIONS
MENU
Music”, “
Photo”, or
Video” from the menu, then press
or b.
2 Press V/v repeatedly to select
“Server”, then press
.
3 Press TOOLS/OPTIONS.
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
4
Press V/v repeatedly to select
“Server”, then press
.
Search”, then press
.
The confirmating message appears.
5 Select “Yes”, then press
.
The updated server list appears.
Registering your favorite
content
You can register your favorite content played
back from “ Music”, “ Photo”, or
“
Video” in “My Library”.
The server list appears on the TV screen.
1
Press TOOLS/OPTIONS while
playing back the content.
Press V/v and
to select the
server which holds the content
you want to play back.
2
Press V/v/B/b repeatedly to
select “Add track (picture,
movie) to My Library”, then
press
.
3
Select the number you want to
use to register the content from
the list, then press
.
The content list appears on the TV screen.
5
Press V/v/B/b repeatedly to
select content you want to play
back from the content list, then
press
.
The playback screen appears on the TV
screen, and content you selected is played
back.
The content you chose will be registered
in “My Library”.
79GB
STR-DN2010
4-182-049-11(1)
Using Network Features
3
Press V/v repeatedly to select
“ Music”, “
Photo”, or
“
Video”, then press
or
b.
4 Press V/v repeatedly to select “Server
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Playing back content registered
in My Library
1
Select “ Music”, “
Photo”,
or “
Video” from the menu,
then press
or b.
2
Press V/v repeatedly to select
“My Library”, then press
.
3
Press V/v repeatedly to select
content you want to play back
from the content list.
The playback screen appears on the TV
screen and content you selected is played
back.
Note
You cannot register content played back from “My
Library” in “My Library”.
masterpage: Left
Selecting the playback mode
You can select the playback mode of the Music
category.
1
Press TOOLS/OPTIONS while
the music selections are
displayed on the list*, or while
listening to the music.
* TOOLS/OPTIONS may not work,
depending on the type of content.
2
Press V/v repeatedly to select
“Repeat” or “Shuffle”, then
press
.
3
Press V/v repeatedly to select
the mode you want, then press
.
x Repeat
You can enjoy content on the server by using
the following buttons on the remote.
Press AMP to operate the receiver using the
remote.
Plays back one or all the tracks
repeatedly.
• Off
Deactivates the repeat play mode.
• One
Plays back one track repeatedly.
• All
Plays back all the tracks repeatedly.
Type of
content
x Shuffle
Using the remote to play back
content
Remote
button
Music
Photo
Video
N
z
z
z
x
z
z
z
X
z
z**
z
>
z
z**
.
z
z**
M
z*
z*
m
z*
z*
Plays back all the tracks in random order.
• Off
Deactivates the shuffle play mode.
• On
Activates the shuffle play mode.
* This button may not work depending on the
connected server or the content type.
**This button is available when photos are played
back in the slideshow mode or from “My
Library”.
80GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
To play back a photo together
with background music (BGM)
You can enjoy photos with music registered in
“My Library” as background music.
1 Play back a photo from “Server”
(page 78) or “My Library” (page 80).
If you play back a photo from “Server”,
you can play back a single photo or a
slideshow of photos listed on the screen.
If you select a photo from “My Library”,
photos in “My Library” will be played back
in sequence in the slideshow mode.
2 Press TOOLS/OPTIONS.
3 Press V/v repeatedly to select “BGM”,
then press
.
masterpage: Right
Using a controller
You can do the following using a device which
has a control function on the home network.
– Playing back content stored on the server
with the receiver.
– Operating the receiver using Windows 7
based computer with Windows Media Player
12.
Note
Before you operate the receiver using a controller,
you have to set the controller you want to use to
match the receiver. Set “External Control” to “ON”,
then set “Controllers” in the Network Settings menu.
For details on settings for controllers, see
“Controllers” (page 119).
4 Press V/v repeatedly to select the
Enjoying content stored on the
server
You can enjoy or check the status of content
(music, photos and videos) on the server using
a controller.
The following operation are supported.
• Playback, stop, pause, fast forward and fast
backward of content
• Go to the next/previous content item
• Check the elapsed time of the currently
playing content
Notes
• Some operation may not be performed, depending
on the device used as a controller, the content type,
or the server. For details, refer to the operating
instructions of each device.
• If you operate the receiver using the supplied
remote together with a controller, the receiver may
not work properly.
continued
81GB
STR-DN2010
4-182-049-11(1)
Using Network Features
mode you want, then press
.
• Off
Stops playback of background music.
• On
Plays back all the tracks in “My Library”
repeatedly.
• On (Shuffle)
Plays back all the tracks in “My Library”
repeatedly in random order.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Computer
(server, controller)
This receiver
1
Select the device to be used as
a server using a controller on
the home network.
2
Select the content you want to
play back using a controller on
the home network.
3
Select the receiver to be used
to play back the content using a
controller on the home
network.
Refer to the operating instructions of each
device.
82GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Listening to Rhapsody
1
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
3
Press V/v repeatedly to select
“Network”, then press
.
4
Press V/v repeatedly to select
“Rhapsody Account”, then
press
.
Rhapsody Digital Music Service
Play all the music you want with Rhapsody®
Thousands of artists. Millions of songs.
Rhapsody is the critically-acclaimed digital
music service that gives you unlimited access
to a massive music catalog of millions of songs
and thousands of artists. You’ll also get
exclusive content, personalized
recommendations, DJ/ad-free listening on
“Rhapsody Radio” and more.
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
(USA model only)
You can enjoy the Rhapsody Digital Music
Service by connecting your receiver to the
Internet.
Rhapsody is only available in the U.S.
masterpage: Right
The confirmation screen for account input
appears on the TV screen.
5
Using Network Features
For more information go to:
www.rhapsody.com/sonystr
Press B/b repeatedly to select
“Yes”, then press
.
The account input screen appears on the
TV screen.
GUI MODE
6
V/v/B/b,
TOOLS/
OPTIONS
MENU
Setting an account
Before using the Rhapsody Digital Music
Service, it is necessary to register an account
using your computer.
Refer to www.rhapsody.com/sonystr for
details.
Sign in using your account on the receiver.
Press V/v repeatedly to select
the Username box, then press
.
The soft keyboard appears on the TV
screen.
7
Press V/v/B/b and
to select
a character one by one to enter
your username.
8
Press V/v/B/b repeatedly to
select “Finish”, then press
9
.
Press V/v repeatedly to select
the Password box, then press
.
10 Press V/v/B/b and
to select
a character one by one to enter
your password.
continued
83GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
11 Press V/v/B/b repeatedly to
select “Finish”, then press
.
12 Press V/v repeatedly to select
“Finish”, then press
.
Note
Repeat the process again from step 6 if the sign in
fails.
To check the account
information
1 Select “
then press
Settings” from the menu,
or b.
Selecting the station from the
Rhapsody Stations list
You can select the station you want to listen
using the Rhapsody Stations list.
1
Select “
Rhapsody” from
the menu, then press
or b.
2
Press V/v repeatedly to select
“Rhapsody Radio”, then press
or b.
3
Press V/v/B/b repeatedly to
select the station you want to
listen to, then press
.
2 Press V/v repeatedly to select
“Network”, then press
.
The reception screen appears on the TV
screen and the station you selected is
received.
3 Press V/v repeatedly to select
“Rhapsody Account”, then press
masterpage: Left
.
4 Press TOOLS/OPTIONS.
5 Press V/v repeatedly to select
“Account Information”, then press
.
The account type and the customer support
ID appear on the TV screen.
To delete an account
1 Select “ Settings” from the menu,
then press
or b.
2 Press V/v repeatedly to select
“Network”, then press
Selecting the track using Music
Guide
The Music Guide displays a variety of music
selections to sample, including top tracks and
artists, and recommendations.
Select genre names, charts, and new releases
anywhere in the Music Guide pages to browse
more.
1
Select “
Rhapsody” from
the menu, then press
or b.
2
Press V/v repeatedly to select
“Rhapsody Music Guide”, then
press
or b.
3
Press V/v repeatedly to select
“Genres”, “Charts”, “New
Releases”, or “Rhapsody
Recommends”, then press
.
.
3 Press V/v repeatedly to select
“Rhapsody Account”, then press
.
4 Press TOOLS/OPTIONS to select
“Remove Account”, then press
.
5 Press B/b repeatedly to select “Yes”,
then press
.
The username and password are deleted.
84GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
4
Press V/v/B/b to select the
track you want to listen to from
the list, then press
.
Registering your favorite track,
album, or station
The playback screen appears on the TV
screen and the track you selected is
played back.
You can register your favorite track, album, or
station in “My Library” while playing back the
track or during reception.
You can select the track, album or station that
you registered in “My Library” from “My
Artists”, “My Albums”, “My Genres”, “My
Tracks”, “My Playlists”, or “My Stations”.
Searching for a track, album, or
artist you want to listen to
You can search for a track, album, or artist
using the search function.
1
Select “
Rhapsody” from
the menu, then press
or b.
Press V/v repeatedly to select
“Search”, then press
or b.
3
Press V/v repeatedly to select
“Artists”, “Albums”, or
“Tracks” you want to search for,
then press
.
5
1
Press TOOLS/OPTIONS while a
track is playing back or you are
selecting a station.
2
Press V/v repeatedly to select
“Add track to My Library”, “Add
album to My Library”, or “Add
station to My Library”, then
press
.
The track, album, or station you chose
will be registered in “My Library”.
The soft keyboard appears on the TV
screen.
To remove a track, album, or
station registered in My Library
Press V/v/B/b and
to select
a character one by one to enter
the title or name you want to
search for.
1 Press TOOLS/OPTIONS while a track
Press V/v/B/b to select
“Finish”, then press
.
Wait until the search result is displayed.
6
Press b to select the search
results.
7
Press V/v/B/b repeatedly to
select the track you want to
listen to from the search result,
then press
.
You can remove a track, album, or station you
registered in “My Library”.
is playing back or you are selecting a
station.
2 Press V/v repeatedly to select “Delete
album from My Library”, “Delete track
from My Library”, or “Delete station
from My Library”, then press
.
The confirmation screen of deletion
appears on the TV screen.
3 Press B/b repeatedly to select “Yes”,
then press
.
The deletion is completed.
The playback screen appears on the TV
screen, and track you selected is played
back.
85GB
STR-DN2010
4-182-049-11(1)
Using Network Features
2
4
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Selecting a track, playlist or
station registered in My Library
You can select a track, playlist or station
registered in “My Library”.
1
Select “
Rhapsody” from
the menu, then press
or b.
2
Press V/v repeatedly to select
“My Library”, then press
.
3
Press V/v/B/b to select the
track you want to listen to using
My Library list, then press
.
masterpage: Left
Listening to SHOUTcast
SHOUTcast is a digital audio streaming
technology-based radio service.
SHOUTcast is a directory of internet radio
stations, allowing users to access thousands of
free online radio stations from DJs and
broadcasters around the world.
Refer to http://www.shoutcast.com for details.
GUI MODE
V/v/B/b,
My Library list
My Artists > Artist(s)* > Albums(s)* > Track(s)*
RETURN/
EXIT O
My Albums > Album(s)* > Track(s)*
TOOLS/
OPTIONS
MENU
My Genres > Genre(s)* > Artist(s)* > Album(s)* >
Track(s)*
My Tracks > Track(s)*
My Playlists > Playlist(s)* > Track(s)*
My Stations > Station(s)*
*The number of lists displayed on the screen
depends on the status of the Rhapsody Digital
Music Service you are using.
The playback screen appears on the TV
screen and the track you selected is
played back.
Selecting a SHOUTcast station
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ SHOUTcast”, then press
or b.
3
Press V/v repeatedly to select
“Preset List”, “0-9”, or A to Z,
then press
.
4
Press V/v repeatedly to select
the genre you want to listen to,
then press
.
86GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
5
Press V/v/B/b to select the
station you want to listen to,
then press
.
The reception screen appears on the TV
screen, and the station you selected is
received.
Notes
• When the number of stations is large, up to 100
stations can be displayed (in order) on this receiver.
• The audio supplied in a format that is not supported
by this receiver does not appear on the list.
Presetting favorite stations
You can register your favorite SHOUTcast
stations on the receiver.
Press TOOLS/OPTIONS while
listening to the radio station.
2
Press
to select “Add to
Preset List”.
Selecting preset stations
You can select your favorite stations from
among the stations you registered.
1
Select “ SHOUTcast” from
the menu, then press
or b.
2
Press V/v repeatedly to select
“Preset List”, then press
.
3
Press V/v repeatedly to select
the preset number station you
want to listen to, then press
.
The reception screen appears on the TV
screen, and the station you selected is
received.
Using Network Features
1
masterpage: Right
The preset number list appears on the TV
screen.
3
Press V/v repeatedly to select
the preset number you want to
preset, then press
.
Note
If you select a list number for which a station has
already been registered, the previously registered
station will be overwritten.
To return to the previous screen
Press RETURN/EXIT O.
87GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Features of the Setup
Manager application
software
You can check the settings of the receiver, and
adjust those settings using your computer, as
well as using the receiver, after installing the
Setup Manager application software provided
on the CD-ROM supplied with the receiver.
Installing the Setup Manager
application software on a
computer
1
Turn on your computer and
login as an administrator.
2
Insert the supplied CD-ROM
into the CD-ROM drive of your
computer.
The installation launcher starts
automatically, then a Software Setup
screen appears on the screen.
If the installation launcher does not start
automatically, double-click
“SetupLauncher.exe” on the disc.
The following settings cannot be set using the
computer with the Setup Manager application
software.
• Auto Calibration
• Speaker
– Test Tone
• S-AIR
CD-ROM (Setup
Manager application
software) (supplied)
System Requirements
Operating System
Windows 7 Starter/Home Premium/
Professional/Ultimate (32bit/64bit)
Windows Vista Home Basic/Home Premium/
Business/Ultimate (SP2, 32bit/64bit)
Windows XP Home Edition/Professional
(SP3, 32bit)
masterpage: Left
3
Install the Setup Manager
application software following
the instructions given in the
message on the screen.
Computer
CPU: Celeron, Pentium III or higher
Clock Speed: 1 GHz or higher
RAM: 512 MB or more
HDD: 20 MB or more free disk space
(280 MB free disk space is required when
.NET Framework 2.0 is not installed.)
Monitor: 1024 × 768, High Color
(65536 colors)
Network: 100Base-TX or higher
88GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Updating the receiver software
using the Setup Manager
You can update the receiver software using the
Setup Manager application software provided
on the CD-ROM supplied with the receiver.
Refer to the HELP of the Setup Manager for
details on operations of the Setup Manager.
Before updating the receiver software, set
“UPDATE(PC)” from “DENY” to “PERMIT”
using the display of the receiver so that the
receiver software can be updated using a
computer (page 127).
masterpage: Right
“BRAVIA” Sync Features
What is “BRAVIA” Sync?
“BRAVIA” Sync is compatible with Sony TV,
Blu-ray Disc/DVD player, AV amplifier, etc.,
that is equipped with the Control for HDMI
function.
By connecting Sony components that are
compatible with the “BRAVIA” Sync with an
HDMI cable (not supplied), operation is
simplified as follows:
• One-Touch Play (page 91)
• System Audio Control (page 92)
• System Power-Off (page 93)
• Theater/Theatre Mode Sync (page 93)
1
Download the update program
from the support website on the
computer to which you
installed the Setup Manager.
2
Click “System” in the Setup
Manager window on the
computer screen, then click
“Browse...” and specify the
path of the update program,
and click “Start Update”.
Control for HDMI is a mutual control function
standard used by HDMI CEC (Consumer
Electronics Control) for HDMI (HighDefinition Multimedia Interface).
The MULTI CHANNEL DECODING
indicator on the front panel flashes while
updating.
When updating complete, the receiver
will restart automatically.
Note
We recommend that you connect the receiver
to products featuring “BRAVIA” Sync.
Notes
• Do not turn the receiver off or disconnect the
network cable during software updating. It may
cause a malfunction.
• It may take 50 minutes for the software updating to
complete.
To check the HELP
When you want to check the HELP of the
Setup Manager application software,
click [Start] – [All Programs] – [Setup
Manager] – [Help for Setup Manager], in that
order.
89GB
STR-DN2010
4-182-049-11(1)
“BRAVIA” Sync Features
Depending on the connected component, the
Control for HDMI function may not work. Refer to
the operating instructions of the component.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Preparing for the
“BRAVIA” Sync
The receiver is compatible with the “Control
for HDMI-Easy Setting” function.
• If your TV is compatible with the “Control
for HDMI-Easy Setting” function, you can
set the Control for HDMI function of the
receiver and playback components
automatically by setting the TV (page 90).
• If your TV is not compatible with the
“Control for HDMI-Easy Setting” function,
set the Control for HDMI function of the
receiver, playback components and TV
individually (page 90).
If your TV is compatible with the
“Control for HDMI-Easy Setting”
function
The Control for HDMI function of the receiver
can be turned on simultaneously by turning on
the Control for HDMI function of the TV.
1 Connect the receiver, TV and playback
components via HDMI connection
(page 25).
(The respective components must be
compatible with the Control for HDMI
function.)
2 Turn on the receiver, TV and playback
components.
3 Turn on the Control for HDMI function
of the TV.
The Control for HDMI function of the
receiver and all the connected components
are turned on simultaneously. When the
setup is completed, “COMPLETE” will
appear.
masterpage: Left
If your TV is not compatible with
the “Control for HDMI-Easy
Setting” function
GUI MODE
V/v/b,
MENU
1 Perform the steps given in “If your TV is
compatible with the “Control for HDMIEasy Setting” function” (page 90).
2 Press GUI MODE.
After “GUI ON” appears on the display for
a while, the GUI menu appears on the TV
screen.
Press MENU if the GUI menu does not
appear on the TV screen.
3 Press V/v repeatedly to select
“
Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
4 Press V/v repeatedly to select “HDMI”,
then press
.
5 Press V/v repeatedly to select “Control
for HDMI”, then press
or b.
6 Press V/v repeatedly to select “ON”,
then press
.
The Control for HDMI function is set to on.
7 Press GUI MODE to exit the GUI menu.
If the GUI menu is displayed, the Control
for HDMI function of the playback
components will not work properly.
For details on setup of the TV, refer to the
operating instructions of your TV.
90GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
8 Set the Control for HDMI function of the
connected component to on.
If the Control for HDMI function for the
connected component is already set to on,
you do not need to change the setting.
For details on setting the TV and connected
components, refer to the operating
instructions of the respective components.
Notes
• Before you do the “Control for HDMI-Easy
Setting” from the TV, be sure to turn on the TV,
connected components and receiver.
• If the playback components cannot function after
you have made the settings for “Control for HDMIEasy Setting”, check the Control for HDMI setting
on your TV.
• If the connected components do not support
“Control for HDMI-Easy Setting”, you need to set
the Control for HDMI function for the connected
components to on before you perform the “Control
for HDMI-Easy Setting” from the TV.
• When you assign the component video input to the
HDMI input using the Input Assign function, you
cannot set “Control for HDMI” to “ON”.
Playing back components
with one-touch operation
(One-Touch Play)
By a simple operation (one-touch),
components connected to the receiver with
HDMI connections start automatically. You
can enjoy the sound/image using connected
components.
When you set “Pass Through” to “AUTO” or
“ON”, sound and image can be output only
from the TV while the receiver remains in
standby mode.
When you start playback a connected
component, the receiver and TV operation are
simplified as follow:
Receiver and TV
Turns on (if in standby mode)
Switches to appropriate HDMI input
• Depending on the TV, the start of the content may
not be output.
• Depending on the settings, the receiver may not
turns on when “Pass Through” is set to “AUTO” or
“ON”.
Tip
You can also select a connected component, such as
DVD/Blu-ray Disc player using the TV menu. The
receiver and TV will automatically switch to the
appropriate HDMI input.
91GB
STR-DN2010
4-182-049-11(1)
“BRAVIA” Sync Features
Notes
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Notes
Enjoying the TV sound
from the speakers
connected to the receiver
(System Audio Control)
You can enjoy the TV sound from the speakers
connected to the receiver by a simple
operation.
You can operate System Audio Control
function using the TV menu. For details, refer
to the operating instructions of the TV.
TV
Sets System
Audio Control
to on
Minimizes TV
volume
• If System Audio Control does not function
according to your TV setting, refer to the operating
instructions of the TV.
• When “Control for HDMI” is set to “ON”, the
“Audio Out” settings in the HDMI Settings menu
will set automatically depending on the System
Audio Control settings.
• When you connect a TV that does not have System
Audio Control function, the System Audio Control
function does not work.
• If the TV is turned on before turning on the
receiver, the TV sound will not be output for a
moment.
Receiver
• Turns on (if in
standby mode)
• Switches to
appropriate
HDMI input
Outputs TV
sound
You can also use the System Audio Control
function as follows.
• If you turn on the receiver while the TV is
turned on, the System Audio Control
function will automatically be set to on and
the TV sound will output from the speakers
connected to the receiver. However, if you
turn off the receiver, the sound will output
from the TV speakers.
• When you adjust the TV volume, the
receiver’s volume is adjusted
simultaneously.
92GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Turning off the receiver
with the TV
Enjoying movies with the
optimum sound field
(System Power-Off)
(Theater/Theatre Mode Sync)
When you turn the TV off by using the
POWER button on the TV’s remote, the
receiver and the connected components turn
off automatically.
You can also use the receiver’s remote to turn
off the TV.
AV ?/1
TV
Press TV, then press AV ?/1.
The TV, receiver and the components
connected via HDMI are turned off.
Notes
Press THEATER or THEATRE on
the remote of the receiver, TV, or
the Blu-ray Disc player, while
pointing the remote towards the TV.
The sound field switches to “C.ST.EX B”.
To return to the previous sound field, press
THEATER or THEATRE again.
Note
The sound field may not switch depending on the
TV.
Tip
The sound field may be changed back to the
previous one when you change the TV’s input.
“BRAVIA” Sync Features
• Set the TV Standby Synchro to “ON” before using
the System Power-Off function. For details, refer
to the operating instructions of the TV.
• Depending on the status, the connected
components may not be turned off. For details,
refer to the operating instructions of the connected
components.
THEATER/
THEATRE
93GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
S-AIR Operations
Room B
S-AIR sub unit
(S-AIR receiver)
About S-AIR products
This receiver is compatible with the S-AIR
function, which allows wireless sound
transmission between S-AIR products.
There are two types of S-AIR product.
• S-AIR main unit (this receiver):
The S-AIR main unit is for transmitting
sound.
You can use up to 3 S-AIR main units. (The
number of usable S-AIR main unit depends
on the use environment.)
• S-AIR sub unit (not supplied):
The S-AIR sub unit is for receiving sound.
– Surround amplifier: You can enjoy
surround and surround back speakers
sound wirelessly. For details, refer to the
operating instructions supplied with the
surround amplifier.
– S-AIR receiver: You can enjoy system
sound in another room.
These S-AIR products can be purchased as an
option (the S-AIR product lineup differs
depending on the area).
See the notes or instructions for the S-AIR sub
unit in this manual only when the S-AIR sub
unit is used.
masterpage: Left
Room A
S-AIR main unit
(this receiver)
S-AIR sub unit
(surround amplifier)
Notes
• The S-AIR menu and parameters only available
when you have inserted the wireless transmitter.
• When the speaker pattern is set to a setting with
front high speakers, the surround back speakers
sound is not output from surround amplifier even if
the surround amplifier is connected.
94GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
About environments where
S-AIR products (S-AIR main unit
and sub unit) are used
S-AIR products use a radio frequency of
2.4 GHz. Certain electronic equipment or
other factors may cause lost connection or
instability in S-AIR reception.
• Electronic equipment influence
The following may cause interference or
cross talk.
– Cellular phones, cordless phones
– Wireless LAN, personal computers
– Game machines using radio signals
– Microwave ovens
masterpage: Right
Setting up an S-AIR
product
Before using an S-AIR product, be sure to
perform the following settings to establish the
sound transmission.
• Inserting the wireless transmitter/transceiver
(page 36).
• Establishing sound transmission between
the S-AIR main unit and S-AIR sub unit (ID
setting) (page 95).
• Pairing the S-AIR main unit with a specific
S-AIR sub unit (Pairing operation)
(page 96).
GUI MODE
V/v/B/b,
RETURN/
EXIT O
MENU
Establishing sound transmission
between the S-AIR main unit and
S-AIR sub unit (ID setting)
When you match the ID of the S-AIR main
unit and the S-AIR sub unit, you can establish
sound transmission. You can use multiple
S-AIR main unit by setting a different ID for
each unit.
To set the ID of the S-AIR main
unit
1 Press GUI MODE.
After “GUI ON” appears on the display for
a while, the GUI menu appears on the TV
screen.
Press MENU if the GUI menu does not
appear on the TV screen.
continued
95GB
STR-DN2010
4-182-049-11(1)
S-AIR Operations
• Other factors
The following may cause poor reception.
– Materials or structures, such as walls and
floors
– The location where an S-AIR product is
placed
When using S-AIR products, place them as
far as possible from the above electronic
equipment, or place where S-AIR reception
is stable.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
2 Press V/v repeatedly to select
“
Settings”, then press
or b.
The Settings menu list appears on the TV
screen.
3 Press V/v repeatedly to select “S-AIR”,
then press
masterpage: Left
Sound transmission is established as follows
(example):
S-AIR main unit
(this receiver)
Other S-AIR
main unit
.
ID A
ID B
4 Press V/v repeatedly to select “S-AIR
ID”, then press
or b.
5 Press V/v repeatedly to select the ID
(A, B or C) you want, then press
.
The ID of the S-AIR main unit is set. “Set
S-AIR ID of the sub unit to the same as that
of the main unit.” appears.
6 Press
.
7 Press GUI MODE.
The GUI menu turns off.
Tip
To check the current ID, select “S-AIR” in the
Settings menu list. When you pair the S-AIR main
unit with the S-AIR sub unit (page 96), “(Pairing)”
appears beside the ID on the TV screen in the GUI
menu.
To set the ID of the S-AIR sub
unit
Be sure to match the ID on S-AIR sub unit you
want to the S-AIR main unit.
For details on setting the ID of the surround
amplifier and S-AIR receiver, refer to the
operating instructions supplied with the
surround amplifier and S-AIR receiver.
ID A
S-AIR sub
unit
ID A
S-AIR sub
unit
ID B
S-AIR sub unit
Notes
• Sources with copyright protection may not be
playable on S-AIR sub unit.
• If you have connected surround amplifier,
surround sound will not be output from S-AIR
main unit.
Tip
You can use multiple S-AIR main units by setting a
different ID for each component.
Pairing the S-AIR main unit with
a specific S-AIR sub unit
(Pairing operation)
To establish sound transmission, you need to
set the same ID for your S-AIR main unit and
S-AIR sub unit.
However, if your neighbors have S-AIR
products and their IDs are the same as yours,
your neighbors could receive the sound of
your S-AIR main unit or vice versa.
To prevent this, you can pair the S-AIR main
unit with a specific S-AIR sub unit by
performing the pairing operation.
96GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
x Before pairing
Sound transmission is established by the ID
(example).
Your room
2
S-AIR main unit
(this receiver)
3
ID A
ID A
ID A
S-AIR sub unit
Sound transmission is established between the
paired S-AIR main unit and S-AIR sub unit(s)
only.
4
5
Press V/v repeatedly to select
“S-AIR”, then press
.
6
Press V/v repeatedly to select
“Pairing”, then press
or b.
7
S-AIR sub unit
1
The S-AIR main unit starts pairing.
“Pairing. Do the pairing operation with
the S-AIR sub unit.” appears.
ID A
S-AIR sub unit
Pairing
Place the S-AIR sub unit that
you want to pair near the S-AIR
main unit.
Press B/b repeatedly to select
“Yes”, then press
.
8
Start pairing of the S-AIR sub
unit.
Refer to the operating instructions of the
S-AIR sub unit.
continued
97GB
STR-DN2010
4-182-049-11(1)
S-AIR Operations
“Put the S-AIR sub unit near the S-AIR
main unit, and turn on power. Start
pairing.” appears on the TV screen. The
S-AIR main unit is ready to start pairing.
No transmission
ID A
Press V/v repeatedly to select
“ Settings”, then press
or
b.
The Settings menu list appears on the TV
screen.
Neighbor
S-AIR main unit
(this receiver)
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
x After pairing
Your room
Match the IDs of the S-AIR main
unit and the S-AIR sub unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main
unit” (page 95).
• To set the ID of the S-AIR sub unit,
refer to the operating instructions
supplied with the S-AIR sub unit.
Neighbor
S-AIR sub unit
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Notes
• Perform pairing within 5 minutes in step 7. If
you do not, pairing is recognized as failed,
and the screen changes accordingly. In this
case, see “If pairing fails” (page 98).
• When sound transmission is established,
“Pairing complete. To perform pairing to
another unit, select “Continue”.” appears.
9
Press B/b repeatedly to select
“Finish” or “Continue”, then
press
.
• “Finish”: Finishes pairing.
• “Continue”: Continues to perform
pairing to another S-AIR sub unit.
Enjoying the system’s
sound in another room
(For the S-AIR receiver only (not
supplied))
You can enjoy the system’s sound in another
room by using the S-AIR receiver. The S-AIR
receiver can be placed in another room for
enjoying the system’s sound there.
For details of the S-AIR receiver, refer to the
operating instructions supplied with the S-AIR
receiver.
Tip
GUI MODE
You can confirm the pairing completion or the
current ID by checking the “S-AIR Settings”
screen. “(Pairing)” appears beside the current
S-AIR ID.
V/v/b,
10 Press GUI MODE.
The GUI menu turns off.
MENU
Note
After you have performed pairing, if you select the
“S-AIR ID” menu, the ID setting (“A”, “B” or “C”)
that you last used is displayed.
If pairing fails
“Pairing failed. Retry?” appears.
To perform pairing again, select “Yes”.
To finish pairing, select “No”.
To quit pairing during setting
Press RETURN/EXIT O.
To cancel pairing
Perform the ID setting of the main unit
according to the procedure of “To set the ID of
the S-AIR main unit” (page 95). If you reset
the ID (even the same ID again), pairing is
canceled.
1
Set the ID of the S-AIR receiver
to match the ID of the S-AIR
main unit.
• To set the ID of the S-AIR main unit,
see “To set the ID of the S-AIR main
unit” (page 95).
• To set the ID of the S-AIR receiver,
refer to the operating instructions
supplied with the S-AIR receiver.
Notes
• When you are using another S-AIR sub unit,
such as a surround amplifier, do not change
the ID of the S-AIR main unit. Set the ID of
the S-AIR receiver to match the ID of the
S-AIR main unit.
• When you pair the S-AIR main unit and
another S-AIR sub unit, such as a surround
amplifier, you also need to pair the S-AIR
main unit and the S-AIR receiver. For details,
see “Pairing the S-AIR main unit with a
specific S-AIR sub unit (Pairing operation)”
(page 96).
98GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
2
Press GUI MODE.
8
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
3
4
masterpage: Right
Select the input you want on
the S-AIR receiver.
x When “PARTY” is set
The S-AIR receiver’s function changes
sequentially as you press INPUT
SELECTOR +/– on the receiver or
S-AIR CH of the S-AIR receiver.
Press V/v repeatedly to select
“ Settings”, then press
or
b.
x When “SEPARATE” is set
The Settings menu list appears on the TV
screen.
The S-AIR receiver’s function changes
by pressing S-AIR CH of the S-AIR
receiver.
Press V/v repeatedly to select
“S-AIR”, then press
.
Notes
5
Press V/v repeatedly to select
“S-AIR Mode”, then press
or b.
6
Press V/v repeatedly to select
the setting you want, then
press
.
9
Adjust the volume on the S-AIR
receiver.
Notes
• The sound of the S-AIR receiver may be cut off by
operation of the S-AIR main unit.
• When the sound is other than 2 channel stereo,
multi channel sound is downmixed to 2 channel.
• Signals with a sampling frequency of more than
96 kHz cannot output to the S-AIR receiver.
* USA model only.
Note
When the input selected on the S-AIR
receiver is same as S-AIR main unit, the
input of the S-AIR receiver will change
according to the S-AIR main unit.
7
Press GUI MODE.
The GUI menu turns off.
continued
99GB
STR-DN2010
4-182-049-11(1)
S-AIR Operations
• PARTY: The S-AIR receiver outputs
sound according to the input selected on
the S-AIR main unit.
• SEPARATE: You can select the input
you want for the S-AIR receiver while
the input of the S-AIR main unit remain
unchanged. When “SEPARATE” is
selected, you can only select “SA-CD/
CD”, “DMPORT”, “FM TUNER”,
“AM TUNER”, “SIRIUS”*,
“SERVER”, “Rhapsody”*,
“SHOUTcast” and the input that is
currently selected on the S-AIR main
unit.
• When “FM TUNER” or “AM TUNER” is
selected on the S-AIR main unit, you can only
select the same band for the tuner on the
S-AIR receiver. However, you can select
input other than TUNER on the S-AIR
receiver.
• When a network function (“SERVER” or
“Rhapsody” or “SHOUTcast”) is selected on
the S-AIR main unit, you can only select the
same network function on the S-AIR receiver
as function on the S-AIR main unit. However,
you can select input other than network
functions on the S-AIR receiver.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
To control the system from the
S-AIR receiver
You can control the system from the S-AIR
receiver by using the following buttons.
Press
Operation
N, X, x,
Share the same operations on the
remote
./>
S-AIR CH
Change the function of the
system
For details, refer to the operating instructions
of the S-AIR receiver.
masterpage: Left
Changing the channel
for better sound
transmission
If you use multiple wireless systems which
share the 2.4 GHz band, such as wireless LAN
or Bluetooth, the transmission of S-AIR
products or other wireless systems may be
unstable. In this case, transmission may be
improved by changing the “RF Change”
setting.
GUI MODE
V/v/b,
MENU
1
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“S-AIR”, then press
.
4
Press V/v repeatedly to select
“RF Change”, then press
or
b.
100GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
5
6
Press V/v repeatedly to select
the setting you want, then
press
.
Stabilizing S-AIR
reception
• OFF: The system transmits sound by
fixing the channel for transmitting.
• ON: The system transmits sound by
searching for a better channel for
transmitting.
• AUTO: Normally select this. The
system changes “RF Change” to “ON”
or “OFF” automatically.
Check the following when S-AIR reception is
poor or unstable.
– Confirm the wireless adapters are inserted
correctly (page 36).
– Confirm that the S-AIR IDs of the S-AIR
main unit and sub unit are the same
(page 95).
Press GUI MODE.
The GUI menu turns off.
7
masterpage: Right
When you set “RF Change” to
“OFF”, select the ID so that
sound transmission is most
stable.
When S-AIR reception is poor
Check the following.
• Keep cords that are connected to the S-AIR
product (AC power cord (mains lead),
speaker cords, or other cords) away from the
wireless adapter and slot.
Notes
S-AIR Operations
• In most cases, you will not need to change this
setting.
• If “RF Change” is set to “OFF”, transmission
between the S-AIR main unit and S-AIR sub unit
can be performed using one of the following
channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing
the transmission channel (frequency) of the other
wireless system(s). For details, refer to the
operating instructions of the other wireless
system(s).
• Keep as much space as possible around
S-AIR products.
– Avoid placing S-AIR products on top of or
directly below other electronic equipment.
– Avoid placing S-AIR products in a closed
rack, metal rack or under a table.
continued
101GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
• Adjust the location (height, orientation, and
place in the room) of S-AIR products until
reception is the most stable.
– Place so that the wireless adapters of the
S-AIR main unit and sub unit are closer.
masterpage: Left
Enjoying the S-AIR
receiver while the S-AIR
main unit is in standby
mode
(For the S-AIR receiver only (not
supplied))
You can enjoy the S-AIR receiver while the
S-AIR main unit is in standby mode by setting
“S-AIR Standby” to “ON”.
GUI MODE
V/v/b,
– Place so that S-AIR products are separated
from other wireless devices.
MENU
1
– Place so that S-AIR products are separated
from metal doors or tables.
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
If you still cannot improve S-AIR reception,
change the “RF Change” setting (page 100).
2
Press V/v repeatedly to select
“ Settings”, then press
or
b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“S-AIR”, then press
.
4
Press V/v repeatedly to select
“S-AIR Standby”, then press
or b.
102GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
5
Press V/v repeatedly to select
the setting you want.
• OFF: You cannot enjoy the S-AIR
receiver while the S-AIR main unit is in
standby mode.
• ON: You can enjoy the S-AIR receiver
while the S-AIR main unit is in standby
mode or turned on.
To exit the menu
Press MENU.
Notes
Other Operations
Switching between
digital and analog audio
(INPUT MODE)
When you connect components to both digital
and analog audio input jacks on the receiver,
you can fix the audio input mode to either of
them, or switch from one to the other,
depending on the type of material you intend
to watch.
1
Press INPUT SELECTOR +/– on
the receiver to select the input.
You can also use the input buttons on the
remote.
2
Press INPUT MODE repeatedly
on the receiver to select the
audio input mode.
The selected audio input mode appears on
the display.
• AUTO
Gives priority to digital audio signals
when there are both digital and analog
connections.
If there are no digital audio signals,
analog audio signals are selected.
When TV input is selected, priority is
given to the Audio Return Channel
(ARC) signals. If your TV is not
compatible with the Audio Return
Channel (ARC) function, the digital
optical audio signals are selected.
• OPT
Appears only when TV input is
selected, and specifies the digital optical
audio signals input to the TV OPTICAL
IN jack.
• ANALOG
Specifies the analog audio signals input
to the AUDIO IN (L/R) jacks.
continued
103GB
STR-DN2010
4-182-049-11(1)
Other Operations
• When you set “S-AIR Standby” to “ON”, the
power consumption increases during the standby
mode.
• When the wireless transmitter is removed from the
S-AIR main unit, “S-AIR Standby” is set to “OFF”
automatically.
• When “S-AIR Mode” is set to “SEPARATE”, if
you have selected “FM TUNER” or “AM TUNER”
on the S-AIR main unit before you turn it off and
“S-AIR Standby” is set to “ON”, you can only
select the same band for the tuner on the S-AIR
receiver. However, you can select input other than
TUNER on the S-AIR receiver.
• When “S-AIR Mode” is set to “SEPARATE”, if
you have selected a network function (“SERVER”
or “Rhapsody” or “SHOUTcast”) on the S-AIR
main unit before you turn it off and “S-AIR
Standby” is set to “ON”, you can only select the
same network function on the S-AIR receiver as
function on the S-AIR main unit. However, you
can select input other than network functions on
the S-AIR receiver.
• The sound of the S-AIR receiver may be cut off by
operation of the S-AIR main unit.
• When the receiver is in standby mode,
“A. STANDBY” appears on the display if “S-AIR
Standby” is set to “ON”.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Notes
• Some audio input modes may not be set up
depending on the input.
• When the HDMI 1-4 input, DMPORT, SERVER,
Rhapsody, SHOUTcast, or SIRIUS input is
selected, “------” appears on the display, and you
cannot select other modes. Select another input,
then set the audio input mode.
• When “A. DIRECT” is being used, audio input is
automatically set to “ANALOG”. You cannot
select other modes.
• The Audio Return Channel (ARC) function does
not work in the following cases.
– Your TV is not compatible with the Audio
Return Channel (ARC) function.
– “Control for HDMI” is set to “OFF”.
– When you do not connect the receiver to the
ARC compatible TV’s HDMI jack via an HDMI
cable.
Enjoying the sound/
images from other inputs
(Input Assign)
You can reassign audio and/or video signals to
another input when they are not currently
being used.
For example when you want to input the only
digital optical audio signals and component
video signals from the DVD player:
DVD player
To OPTICAL
BD IN jack
(audio signal)
To COMPONENT
VIDEO IN 1 jacks
(video signal)
This receiver
1
Assign to DVD input jack
using “Input Assign” in
the Input Option menu.
Press GUI MODE.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“
Input”, then press
or b.
3
Press V/v repeatedly to select
the input name you want to
assign.
4
Press TOOLS/OPTIONS.
The options menu appears.
5
Press V/v repeatedly to select
“Input Assign”, then press
or b.
The “Input Assign” screen appears.
104GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
6
Select the audio and/or video
signals you want to assign to
the input which you selected in
step 3 using V/v/B/b.
7
Press
masterpage: Right
.
Input name
BD
DVD
SAT/ Video1 Video2 SA-CD/ HDMI1 HDMI2 HDMI3 HDMI4
CATV
CD
Assignable Component1
video input
Component2
jacks
Component3
a*
a
a
a
a
a
a**
a**
a**
a**
a
a*
a
a
a
a
a**
a**
a**
a**
a
a
a*
a
a
a
a**
a**
a**
a**
Composite
a
–
a
a*
a*
–
–
–
–
–
HDMI1
a
a
a
a
a
a
a*
–
–
–
HDMI2
a
a
a
a
a
a
–
a*
–
–
HDMI3
a
a
a
a
a
a
–
–
a*
–
HDMI4
a
a
a
a
a
a
–
–
–
a*
None
a
a
a
a
a
a*
–
–
–
–
a
a*
a
a
a
a
–
–
–
–
a*
a
–
a
a
a
–
–
–
–
–
a
a*
a
a
a
–
–
–
–
a
–
a
a*
a*
a*
–
–
–
–
Assignable DVD COAX
audio input
BD OPT
jacks
SAT OPT
Analog
* Initial setting
**When you assign a component video input to the HDMI input via the Input Assign menu, component video
signals are not converted to HDMI video signals and are not output from the HDMI TV OUT jack.
Component video signals are output from the COMPONENT VIDEO MONITOR OUT jack. In this case,
the resolution of the GUI output is set to “480p” for both component video input and HDMI video input.
Notes
Other Operations
• You cannot assign other optical input to the inputs
to which optical input jack is initially assigned.
• When you assign the digital audio input, the
INPUT MODE setting may change automatically.
• You cannot reassign more than one HDMI input to
the same input.
• You cannot reassign more than one digital audio
input to the same input.
• You cannot reassign more than one component
video input to the same input.
• When you assign a component video input to the
HDMI input, set “Control for HDMI” to “OFF”.
105GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Notes
Using a bi-amplifier
connection
1 Press GUI MODE.
• Set “Sur Back Assign” to “BI-AMP” before you
perform Auto Calibration.
• If you set “Sur Back Assign” to “BI-AMP”, the
speaker level and distance settings of the surround
back speakers and front high speakers become
invalid, and those of the front speakers are used.
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
2
Press V/v repeatedly to select
“
Settings” then press
or
b.
The Settings menu list appears on the TV
screen.
3
Press V/v repeatedly to select
“Speaker”, then press
.
4
Press V/v repeatedly to select
“Speaker Pattern”, then press
or b.
5
Press V/v repeatedly to select
the appropriate speaker pattern
so that there are no surround
back speakers and front high
speakers, then press
.
6
Press V/v repeatedly to select
“Sur Back Assign”, then press
or b.
7
Press V/v repeatedly to select
“BI-AMP”, then press
.
The same signals output from the
SPEAKERS FRONT A terminals can be
output from the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals.
To exit the menu
Press MENU.
106GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
2
Adjusting Settings
Using the Settings menu
masterpage: Right
Press V/v repeatedly to select
“ Settings”, then press
or
b to enter the menu mode.
The Settings menu list appears on the TV
screen.
You can adjust various settings for speakers,
surround effects, etc. using the Settings menu.
To display the menu of the receiver on the TV
screen, make sure that the receiver is in “GUI
MODE” by following the steps in “To turn
“GUI MODE” on and off” (page 52).
GUI MODE
V/v/b,
3
RETURN/
EXIT O
Press V/v repeatedly to select
the menu item you want, then
press
.
Example: When you select “Auto
Calibration”.
MENU
Auto Calibration
1
Press GUI MODE.
Calibration Start
Calibration Type
After “GUI ON” appears on the display
for a while, the GUI menu appears on the
TV screen.
Press MENU if the GUI menu does not
appear on the TV screen.
Position :
Pos. 1
OPTIONS Function List
4
Press V/v repeatedly to select
the parameter you want, then
press
.
To return to the previous screen
Press RETURN/EXIT O.
Adjusting Settings
To exit the menu
Press MENU.
continued
107GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Settings menu list
Settings menu
Description
Auto Calibration
Sets the speaker level or
distance and makes the
measurement automatically
(page 108).
Speaker
Sets the speaker position
manually (page 109).
Surround
Selects the sound field and
adjusts the surround effect
you choose (page 113).
EQ
Adjusts the equalizer (bass/
treble sound) (page 114).
Audio
Sets various sound items
(page 114).
Video
Adjusts the resolution of
analog video signals (page
116).
HDMI
Makes settings for sound/
images from components
connected to the HDMI jacks
(page 117).
Network
Makes settings for the
network (page 118).
S-AIR
Makes settings for S-AIR
operations (page 94).
System
Makes settings for the
system of the receiver
(page 121).
Auto Calibration menu
Calibration Start
Lets you perform Auto Calibration. For
details, see “Calibrating the appropriate
speaker settings automatically (Auto
Calibration)” (page 42).
Note
The measurement results will be overwritten and
saved as the current seating position you select in
“Position” parameter.
Calibration Type
Lets you select the calibration type for each
seating position. For details, see “3: Saving the
measurement results” (page 46).
Note
You can select this parameter only when you have
performed the Auto Calibration and saved the
measurement result.
Position
You can register 3 patterns as Pos. 1, 2, and 3,
depending on the seating position, listening
environment, and measurement conditions.
To register settings for the
listening environment
You can select the seating position you want
and register the measurement results of the
Auto Calibration for that seating position.
1 Press V/v repeatedly to select the
position (Pos. 1, 2, 3) for which you
want to register the measurement
result, then press
.
2 Press V/v repeatedly to select
“Calibration Start”, then press
or b.
108GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
3 Press V/v repeatedly and
to
uncheck the items you do not want to
measure, then press b.
The confirmation screen, asking whether
you are ready to start measurement,
appears.
4 Press
to select “Start”.
The measurement results is registered as
the position you selected in step 1.
Speaker Settings menu
You can adjust each speaker manually.
You can also adjust the speaker levels after the
Auto Calibration is completed.
Note
The speaker settings are only for the current seating
position.
5 Repeat step 1 to 4 to register another
seating position.
Speaker Pattern
To select the registered seating
position
Press V/v repeatedly to select the position
(Pos. 1, 2, 3) you want, then press
.
The registered seating position is selected.
Select “Speaker Pattern” according to the
speaker system which you are using. Select the
speaker pattern before you perform Auto
Calibration.
Sur Back Assign
To name the seating position
You can rename the position name.
1 Select the position (Pos. 1, 2, 3) you
want, then press
.
2 Press TOOLS/OPTIONS.
3 Select “Name Input”, then press
x OFF
.
4 Press V/v repeatedly to select a
character, then press b.
You can move the input position backward
and forward by pressing B/b.
5 Repeat step 4 to input a character one
by one, then press
.
The name you entered is registered.
Lets you set the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals for a bi-amplifier or speakers front B
connection.
x BI-AMP
x SPEAKER B
Note
When you change the connection from a biamplifier or speakers front B to surround back or
front high speakers connection, set “Sur Back
Assign” to “OFF”, then set up the speakers again.
See “Auto Calibration” (page 42) or “Manual
Setup” (page 110).
Adjusting Settings
109GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Manual Setup
You can adjust each speaker manually on the
“Manual Setup” screen. You can also adjust
the speaker levels after the Auto Calibration is
completed.
masterpage: Left
To adjust the distance from the
seating position to each
speaker
You can adjust the distance from the seating
position to each speaker (front left/right, front
left/right high, center, surround left/right,
surround back left/right, subwoofer).
To adjust the speaker level
1 Press V/v/B/b repeatedly to select the
You can adjust each speaker’s level (front left/
right, front left/right high, center, surround
left/right, surround back left/right,
subwoofer).
2 Press B/b repeatedly to select
1 Press V/v/B/b repeatedly to select the
speaker on the screen for which you
want to adjust the level, then press
.
2 Press B/b repeatedly to select “Level”.
3 Press V/v repeatedly to set the level of
the selected speaker, then press
.
For front left/right speakers, you can adjust
the level from –10.0 dB to +10.0 dB in
0.5 dB steps. For other speakers, you can
adjust the level from –20.0 dB to +10.0 dB
in 0.5 dB steps.
Note
When one of the sound fields for music is selected,
no sound is output from the subwoofer if all the
speakers are set to “Large”. However, the sound will
be output from the subwoofer if
– the digital input signal contains LFE signals.
– the front or surround speakers are set to “Small”.
– the sound field for movie is selected.
– “PORTABLE” is selected.
speaker on the screen for which you
want to adjust the distance from the
seating position, then press
.
“Distance”.
3 Press V/v repeatedly to set the
distance of the selected speaker, then
press
.
You can adjust the distance from 3 feet
3 inches to 32 feet 9 inches (1.00 meter to
10.00 meters) in 1 inch (0.01 meter) steps.
Notes
• Depending on the speaker pattern setting, some
parameters may not be available.
• This function does not work in the following cases.
– “A. DIRECT” is being used.
– Signals with a sampling frequency of more than
96 kHz are being received.
To adjust the size of each
speaker
You can adjust each speaker’s (front left/right,
front left/right high, center, surround left/right,
surround back left/right) size.
1 Press V/v/B/b repeatedly to select the
speaker on the screen for which you
want to adjust the size, then press
.
2 Press B/b repeatedly to select “Size”.
110GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
3 Press V/v repeatedly to set the size of
the selected speaker, then press
.
• Large
If you connect large speakers that will
effectively reproduce bass frequencies,
select “Large”. Normally, select “Large”.
• Small
If the sound is distorted, or you feel a lack
of surround effects when using multi
channel surround sound, select “Small” to
activate the bass redirection circuitry and
output the bass frequencies of each
channel from the subwoofer or other
“Large” speakers.
Note
masterpage: Right
Crossover Freq (Speaker
crossover frequency)
Lets you set the bass crossover frequency of
speakers that the speaker size has been set to
“Small” in the Speaker Settings menu.
Measured speaker crossover frequency is set
for each speaker after the Auto Calibration.
1
Press V/v repeatedly to select
the speaker on the screen you
want to adjust, then press
.
2
Press V/v repeatedly to adjust
the value, then press
.
This function does not work when “A. DIRECT” is
being used.
Tips
Test Tone
You can select the test tone type on the “Test
Tone” screen.
Note
Test tone is not output from the headphones
connected to the S-AIR surround amplifier.
Tips
• To adjust the level of all speakers at the same time,
press MASTER VOL +/– (RM-AAP055 only) or
2 +/– (RM-AAP056 only). You can also use
MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen
during adjustment.
To output test tone from each
speaker
You can output test tone from the speakers in
sequence.
1 Press B/b repeatedly to select “Test
Tone”, then press
.
continued
111GB
STR-DN2010
4-182-049-11(1)
Adjusting Settings
• The “Large” and “Small” settings for each speaker
determine whether the internal sound processor
will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the subwoofer or other “Large”
speakers.
However, since bass sound has a certain amount of
directionality, it is best not to cut it, if possible.
Therefore, even when using small speakers, you
can set them to “Large” if you want to output the
bass frequencies from that speaker. On the other
hand, if you are using a large speaker, but prefer
not to have bass frequencies output from that
speaker, set it to “Small”.
If the overall sound level is lower than you prefer,
set all speakers to “Large”. If there is not enough
bass, you can use the equalizer to boost the bass
levels.
• The surround back speakers will be set to the same
setting as that of the surround speakers.
• When the front speakers are set to “Small”, the
center, surround, and front high speakers are also
automatically set to “Small”.
• If you do not use the subwoofer, the front speakers
are automatically set to “Large”.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• AUTO
The test tone is output from each speaker
in sequence.
• L, C, R, SR, SB*, SBR, SBL, SL, LH,
RH, SW
You can select which speakers will output
the test tone.
* “SB” appears when only one surround back
speaker is connected.
3 Press V/v repeatedly to adjust the
speaker level, then press
.
To output test tone from
adjacent speakers
You can output test tone from adjacent
speakers so that you can adjust the balance
between the speakers.
1 Press B/b repeatedly to select “Phase
Noise”, then press
.
To output the source sound
from adjacent speakers
You can output the source sound from
adjacent speakers so that you can adjust the
balance between the speakers.
1 Press B/b repeatedly to select “Phase
Audio”, then press
.
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• L/C, C/R, R/SL, R/SR, SR/SL, SR/SBR,
SR/SB*, SBR/SBL, SB/SL*, SBL/SL,
SL/L, L/SR, L/RH, LH/RH, LH/R
Lets you output front 2 channel source
sound (instead of the test tone)
sequentially from adjacent speakers.
Some items may not be displayed,
depending on the setting of the speaker
pattern.
* “SR/SB” and “SB/SL” appear when only one
surround back speaker is connected.
3 Press V/v repeatedly to adjust the
2 Press V/v repeatedly to adjust the
parameter, then press
.
• OFF
• L/C, C/R, R/SL, R/SR, SR/SL, SR/SBR,
SR/SB*, SBR/SBL, SB/SL*, SBL/SL,
SL/L, L/SR, L/RH, LH/RH, LH/R
Lets you output the test tone sequentially
from adjacent speakers.
Some items may not be displayed,
depending on the setting of the speaker
pattern.
* “SR/SB” and “SB/SL” appear when only one
surround back speaker is connected.
3 Press V/v repeatedly to adjust the
speaker level, then press
masterpage: Left
.
speaker level, then press
.
When a test tone is not output
from the speakers
• The speaker cords may not be connected
securely. Check to see if they are connected
securely and cannot be disconnected by
pulling on them slightly.
• The speaker cords may have the short-circuit
problem.
When a test tone is output from
a different speaker than the
speaker displayed on the TV
screen
The speaker pattern to the connected speaker
is not set up correctly. Make sure the speaker
connection and the speaker pattern match.
112GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
D.Range Comp (Dynamic range
compression)
Lets you compress the dynamic range of the
soundtrack. This may be useful when you want
to watch movies at low volumes late at night.
Dynamic range compression is possible with
Dolby Digital sources only.
x OFF
The dynamic range is not compressed.
masterpage: Right
Surround Settings menu
You can select the sound field and adjust the
effect level, etc. on the “Sound Field Setup”
screen.
For details on the sound field, see “Enjoying
Surround Sound” (page 73).
Note
The setup items you can adjust on each menu vary
depending on the sound field.
x AUTO
The dynamic range is compressed
automatically.
x STD
The dynamic range is compressed as intended
by the recording engineer.
x MAX
The dynamic range is compressed
dramatically.
Tips
• Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
• “STD” is the standard setting, but it only enacts
light compression. Therefore, we recommend
using the “MAX” setting. This greatly compresses
the dynamic range and lets you view movies late at
night at low volumes. Unlike analog limiters, the
levels are predetermined and provide a very natural
compression.
To select the sound field
1 Press V/v repeatedly to select
Sound Field you want.
2 Press RETURN/EXIT O.
To adjust the effect level for
Cinema Studio EX A/B/C
1 Press V/v repeatedly to select “Cinema
St EX A”, “Cinema St EX B” or “Cinema
St EX C”, then press
.
2 Press V/v repeatedly to select the
Effect Level you want, then press B.
• 150%
• 100%
• 80%
• 50%
Adjusting Settings
Distance Unit
Lets you select the unit of measure for setting
distances.
x meter
The distance is displayed in meters.
x feet
The distance is displayed in feet.
113GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
EQ Settings menu
Audio Settings menu
You can use the following parameters to adjust
the tonal quality (bass/treble level) of front
speakers.
You can make settings for the audio to suit
your preference.
Bass
Treble
Level
(dB)
Frequency
(Hz)
A/V Sync (Synchronizes audio
with video output)
Lets you delay the output of audio to minimize
the time gap between audio output and visual
display.
x 0 ms – 300 ms
Note
This function does not work in the following cases.
– “A. DIRECT” is being used.
– Signals with a sampling frequency of more than 48
kHz are being received.
To adjust the equalizer on the
EQ screen
1 Press .
You can adjust the delay from 0 ms to 300 ms
in 10 ms steps.
Notes
• This function is useful when you use a large LCD
or plasma monitor or a projector.
• This function does not work in the following cases.
– “A. DIRECT” is being used.
– Signals with a sampling frequency of more than
96 kHz are being received.
2 Press B/b repeatedly to select “Bass”
or “Treble”.
3 Press V/v repeatedly to adjust the gain,
then press
.
Dual Mono (Digital broadcast
language selection)
Lets you select the language you want when
you listen to the dual audio of a digital
broadcast. This feature only functions for
Dolby Digital sources.
x MAIN/SUB
Sound of the main language will be output
through the front left speaker and sound of the
sub language will be output through the front
right speaker simultaneously.
x MAIN
Sound of the main language will be output.
x SUB
Sound of the sub language will be output.
114GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Decode Priority (Digital audio
input decoding priority)
Lets you specify the input mode for the digital
signal input to the DIGITAL IN jacks or
HDMI IN jacks.
x PCM
When signals from the DIGITAL IN jack are
selected, PCM signals are given priority (to
prevent interruption when playback starts).
However, when other signals are input, there
may be no sound, depending on the format.
In this case, set this item to “AUTO”.
When signals from the HDMI IN jack are
selected, only PCM signals are output from the
connected player. When signals other than
PCM are received, set this item to “AUTO”.
x AUTO
Automatically switches the input mode
between DTS, Dolby Digital, or PCM.
Notes
• Even when “Decode Priority” is set to “PCM”, the
sound may be interrupted at the very beginning of
the first track depending on the CD being played
back.
• When playback a DTS CD, set “Decode Priority”
to “AUTO” to prevent noise being output.
Adjusting Settings
115GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Video Settings menu
You can make settings for video.
Resolution (Converting video signals)
Lets you convert the resolution of analog video input signals.
Output from
“Resolution”
parameter
HDMI TV OUT
jack
Input from
COMPONENT MONITOR VIDEO
VIDEO MONITOR
OUT jack
OUT jacks
x Direct
COMPONENT VIDEO IN
jacks
–
a
–
VIDEO IN jacks
–
–
a
x Auto
(initial setting)
COMPONENT VIDEO IN
jacks
zb)
zb)
zb)
zb)
za)
VIDEO IN jacks
x 480i/576i
COMPONENT VIDEO IN
jacks
zc)
z
z
VIDEO IN jacks
zc)
z
z
x 480p/576p
COMPONENT VIDEO IN
jacks
z
z
–
VIDEO IN jacks
z
z
a
x 720p
COMPONENT VIDEO IN
jacks
z
zd)
–
VIDEO IN jacks
z
zd)
a
COMPONENT VIDEO IN
jacks
z
a
–
VIDEO IN jacks
z
–
a
x 1080i
x 1080p
z : Video signals are converted and output through the video converter.
a : The same type of signal as that of the input signal is output. Video signals are not converted.
– : Video signals are not output.
a)
The resolution is set automatically, depending on
the connected monitor.
b)
When the TV is connected to jacks other than the
HDMI jacks, 480i/576i signals are output.
c)
480p/576p signals are output even if 480i/576i is
set.
d)
Video signals without copyright protection are
output based on the settings menu. Video signals
with copyright protection are output as 480p/576p.
Notes
• Video signals are not output from the
COMPONENT VIDEO MONITOR OUT or
MONITOR VIDEO OUT jacks when the monitor,
etc., is connected to HDMI TV OUT jack.
• If you select a resolution that the connected TV
does not support in the “Resolution” parameter, the
images from the TV cannot be output correctly.
• Converted HDMI image output does not support
x.v.Color (x.v.Colour), Deep Color (Deep Colour)
and 3D image.
116GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Notes
HDMI Settings menu
You can make the required settings for
components connected to the HDMI jack.
Control for HDMI
Lets you turn the Control for HDMI function
on or off. For details, see “Preparing for the
“BRAVIA” Sync” (page 90).
x ON
x OFF
Note
When you set “Control for HDMI” to “ON”, “Audio
Out” may be changed automatically.
Pass Through
Lets you output the HDMI signals to the TV
even when the receiver is in standby mode.
x OFF
The receiver does not output HDMI signals
when the receiver is in the standby mode.
Turn on the receiver to enjoy the connected
component’s source on the TV. This setting
saves power in the standby mode compared
with the “ON” setting.
x AUTO
x ON
Audio Out
Lets you set the HDMI audio signals from the
playback component connected to the receiver
via an HDMI connection.
x TV+AMP
The sound is output from TV’s speaker and the
speakers connected to the receiver.
Notes
• The sound quality of the playback component
depends on the TV’s sound quality, such as the
number of channels, and the sampling frequency,
etc. When the TV has stereo speakers, the sound
output from the receiver is also stereo as that of the
TV, even if you play back multi channel source.
• When you connect the receiver to an image display
component (projector, etc.), sound may not be
output from the receiver. In this case, select
“AMP”.
• When you select the input that you have assigned
the HDMI input, sound does not output from the
TV.
x AMP
The HDMI audio signals from the playback
component is only output to the speakers
connected to the receiver. Multi channel sound
can be played back as it is.
Note
Audio signals are not output from the TV’s speaker
when “Audio Out” is set to “AMP”.
When the receiver is in the standby mode, the
receiver continuously outputs HDMI signals
from the receiver’s HDMI TV OUT jack.
117GB
STR-DN2010
4-182-049-11(1)
Adjusting Settings
When the TV is turned on while the receiver is
in the standby mode, the receiver outputs
HDMI signals from the receiver’s HDMI TV
OUT jack. Sony recommends this setting if
you use a TV that is compatible with
“BRAVIA” Sync. This setting saves power in
the standby mode compared with the “ON”
setting.
• This parameter is not available when “Control for
HDMI” is set to “OFF”.
• When “AUTO” is selected, it may take a little more
time for the image and sound to be output to the TV
than when “ON” is selected.
• When the receiver is in standby mode,
“A. STANDBY” appears on the display if “Pass
Through” is set to “AUTO” or “ON”. However,
“A. STANDBY” will disappear when “Pass
Through” is set to “AUTO” and no signals are
detected.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Subwoofer Level
Lets you set the level of the subwoofer to 0 dB
or +10 dB when PCM signals are input via an
HDMI connection. You can set the level for
each HDMI input independently.
x 0 dB
masterpage: Left
Network Settings menu
You can make the settings for the network.
Network Setup
Lets you make the network settings.
x +10 dB
x AUTO
Automatically sets the level to 0 dB or +10 dB
depending on the audio stream.
To check the network settings
1 Press V/v repeatedly to select
“Network Setup”, then press
.
2 Press V/v repeatedly to select
Subwoofer LPF (Subwoofer Low
Pass Filter for HDMI)
Lets you turn the low pass filter for the
subwoofer output on or off. The low-pass filter
works when PCM signals are input via an
HDMI connection. Turn the function on if you
connect a subwoofer without the crossover
frequency function.
x OFF
The low pass filter of the subwoofer is turned
off.
x ON
The low pass filter of the subwoofer’s cut off
frequency is set to 120 Hz.
“Network Information”, then press
.
The network setting information of the
receiver is displayed on the TV screen.
To configure network settings
automatically
1 Press V/v repeatedly to select
“Network Setup”, then press
.
2 Press V/v repeatedly to select “Internet
Setup”, then press
.
3 Press V/v repeatedly to select
“Connect Automatically (DHCP)”, then
press
.
“Success! The receiver is now connected to
network.” appears on the TV screen.
4 Press
to select “Finish”.
To set the IP address manually
1 Press V/v repeatedly to select
“Network Setup”, then press
.
2 Press V/v repeatedly to select “Internet
Setup”, then press
.
3 Press V/v repeatedly to select “Manual
Configuration”, then press
.
The setting screen for the IP address
appears on the TV screen.
118GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
4 Press V/v repeatedly to select the IP
address, then press
.
The soft keyboard appears on the TV
screen.
5 Press V/v/B/b and
to select a
character one by one to enter the IP
address.
6 Press V/v/B/b to select “Finish”, then
press
.
7 Press b to display the next screen.
8 Repeat the process in steps 4 to 7
again to enter the Subnet Mask,
Gateway address, DNS1 address, and
DNS2 address.
9 Press V/v repeatedly to select “Test
Connection”, then press
.
“Success! The receiver is now connected to
network.” appears on the TV screen.
10Press
to select “Finish”.
.
.
3 Press V/v repeatedly to select
“Enable”, then press
.
4 Press
.
The soft keyboard appears on the TV
screen.
9 Press V/v/B/b repeatedly to select
“Finish”, then press
.
10Press b.
11Press V/v repeatedly to select “Finish”,
then press
.
External Control
Lets you turn the function which controls the
receiver from external controllers on the home
network on or off.
x OFF
x ON
Note
to select a
character one by one to enter the proxy
server address.
6 Press V/v/B/b repeatedly to select
.
7 Press b to select the Port number box,
then press
.
The soft keyboard appears on the TV
screen.
Lets you set availability of operations allowed
for the receiver for network controllers on the
home network that have attempted to access
the receiver in the past.
1 Press V/v repeatedly to select
“Controllers”, then press
.
The setting screen used for Controllers
appears on the TV screen.
2 Press V/v repeatedly to select the
controller you want to allow to operate
the receiver from the list, then press
to check the box.
When you check the box for “Auto
Permission”, all the controllers detected are
checked automatically.
3 Press V/v/B/b repeatedly to select
“Finish”, then press
.
continued
119GB
STR-DN2010
4-182-049-11(1)
Adjusting Settings
5 Press V/v/B/b and
“Finish”, then press
to select a
character one by one to enter the port
number.
Controllers
2 Press V/v repeatedly to select “Proxy
Setup”, then press
8 Press V/v/B/b and
If you set “Controllers”, set “External Control” to
“ON”.
To set the Proxy server
manually
1 Press V/v repeatedly to select
“Network Setup”, then press
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
To cancel the setup
Press V/v repeatedly to select “Cancel”, then
press
in step 3.
To remove the detected
controllers from the list
1 Press V/v repeatedly to select the
controller you want to remove from the
list, then press
to check the box.
2 Press V/v repeatedly to select
“Remove All”, then press
.
Tip
Up to 10 network controllers that have attempted to
access the receiver are listed, and each of them can
control the receiver.
Rhapsody Account
Lets you enter the Rhapsody Account to listen
to the Rhapsody Internet radio service. For
details, see “Setting an account” (page 83).
Rhapsody is only available in the U.S.
Network Standby
Lets you turn the function that activates the
switching hubs on the rear of the receiver and
allows external control devices to control the
receiver on or off even when the receiver is in
standby mode.
x OFF
The network function turns off when the
receiver is in standby mode.
Device Name
Lets you assign a device name to the receiver
up to 20 characters displayed as being on the
home network.
To assign the device name
1 Press V/v repeatedly to select “Device
Name”, then press
masterpage: Left
.
2 Press
.
The soft keyboard appears on the TV
screen.
x ON
The network function works even when the
receiver is in standby mode.
In addition, the start-up time of the network
function is reduced after the receiver is turned
on.
Note
When the receiver is in standby mode,
“A. STANDBY” appears on the display if “Network
Standby” is set to “ON”.
3 Press V/v/B/b and
to select a
character one by one to enter the
device name.
4 Press V/v/B/b repeatedly to select
“Finish”, then press
.
When the setting is applied to the receiver,
the receiver will restart automatically.
Tip
The default device name is “STR-DN2010”.
120GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
2 Select “Update via Internet”, then press
System Settings menu
You can customize the settings of the receiver.
.
The current software version and latest
software version are displayed on the TV
screen.
3 Press B/b repeatedly to select
Auto Standby
Lets you set the receiver switch to standby
mode automatically when you do not operate
the receiver or when there is no signals input to
the receiver.
x OFF
Does not switch to standby mode.
x ON
Switches to standby mode after approximately
30 minutes.
“Update”, then press
.
A confirmation screen appears on the TV
screen.
4 Press B/b repeatedly to select “Start”,
then press
.
Receiver updating starts.
The MULTI CHANNEL DECODING
indicator on the front panel flashes while
updating.
When the updating complete, the receiver
will restart automatically.
Notes
Notes
• This function does not work in the following cases.
– “FM TUNER”, “AM TUNER”, “SIRIUS”,
“SERVER”, “Rhapsody” or “SHOUTcast” input
is selected.
– S-AIR receiver or surround amplifier is used.
– “External Control” is set to “ON”.
• If you use the Auto standby mode and the Sleep
Timer at the same time, the Sleep Timer has
priority.
Software Version
• In the following cases, a message appears on the
TV screen and the update of the receiver is not
performed.
– When all versions are the latest one.
– When the receiver cannot retrieve the data, such
as when the network has not been set up, or when
the server is down, etc.
• Do not turn the receiver off or disconnect the
network cable during software updating. It may
cause a malfunction.
• It may take 50 minutes for the software updating to
complete.
Adjusting Settings
You can check the version of the software on
the system of the receiver, and you can also
update the software of the receiver.
You can also update the software of the
receiver using the Setup Manager application
software provided on the CD-ROM supplied
with the receiver. For details, see “Updating
the receiver software using the Setup
Manager” (page 89).
To update the receiver using the
menu
1 Press V/v repeatedly to select
“Software Version”, then press
.
121GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
5
Operating without
connecting to a TV
You can operate this receiver using the display
even if the TV is not connected to the receiver.
AMP
masterpage: Left
Press V/v repeatedly to select
the setting you want, then
press
.
To return to the previous
display
Press B or RETURN/EXIT O.
To exit the menu
Press MENU.
Note
Some parameters and settings may appear dimmed
on the display. This means that they are either
unavailable or fixed and unchangeable.
GUI MODE
V/v/B/b,
RETURN/
EXIT O
MENU
Using the menu in the display
Press GUI MODE repeatedly to
select “GUI OFF”.
The receiver is switched to front panel display
mode.
1
2
3
Press AMP.
4
Press V/v repeatedly to select
the parameter you want to
adjust, then press
or b.
Press MENU.
Press V/v repeatedly to select
the menu you want, then press
or b.
122GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Overview of the menus
The following options are available in each menu. For details on navigating through menus, see
page 122.
Menu
[Display]
Parameters
[Display]
Initial
setting
FULL FLAT, ENGINEER,
FRONT REF, OFF
FULL FLAT
Position
[POSITION]
POS. 1, POS. 2, POS. 3
POS. 1
Naming position
[NAME IN]
For details, see “To name the seating
position” (page 109).
Test tonea)
[TEST TONE]
OFF, FIX xxxb), AUTO xxxb)
OFF
Phase noisea)
[P. NOISE]
OFF, LH/FR, LH/RH, FL/RH,
FL/SR, SL/FL, SB/SL, SBL/SL,
SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, CNT/FR, FL/CNT
OFF
Phase audioa)
[P. AUDIO]
OFF, LH/FR, LH/RH, FL/RH,
FL/SR, SL/FL, SB/SL, SBL/SL,
SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, CNT/FR, FL/CNT
OFF
Front left speaker levela)
[FL LEVEL]
FL –10.0 dB to FL +10.0 dB
(0.5 dB per step)
FL 0 dB
Front right speaker levela)
[FR LEVEL]
FR –10.0 dB to FR +10.0 dB
(0.5 dB per step)
FR 0 dB
Center speaker levela)
[CNT LEVEL]
CNT –20.0 dB to CNT +10.0 dB
(0.5 dB per step)
CNT 0 dB
Surround left speaker levela)
[SL LEVEL]
SL –20.0 dB to SL +10.0 dB
(0.5 dB per step)
SL 0 dB
Surround right speaker levela)
[SR LEVEL]
SR –20.0 dB to SR +10.0 dB
(0.5 dB per step)
SR 0 dB
Surround back speaker levela)
[SB LEVEL]
SB –20.0 dB to SB +10.0 dB
(0.5 dB per step)
SB 0 dB
Surround back left speaker
levela)
[SBL LEVEL]
SBL –20.0 dB to SBL +10.0 dB
(0.5 dB per step)
SBL 0 dB
Surround back right speaker
levela)
[SBR LEVEL]
SBR –20.0 dB to SBR +10.0 dB
(0.5 dB per step)
SBR 0 dB
Front left high speaker levela)
[LH LEVEL]
LH –20.0 dB to LH +10.0 dB
(0.5 dB step)
LH 0 dB
Front right high speaker levela)
[RH LEVEL]
RH –20.0 dB to RH +10.0 dB
(0.5 dB step)
RH 0 dB
Auto Calibration Auto Calibration start
settings
[A.CAL START]
[<AUTO CAL>]
Calibration type
[CAL TYPE]
Level settings
[<LEVEL>]
Adjusting Settings
Settings
continued
123GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Menu
[Display]
Speaker settings
[<SPEAKER>]
masterpage: Left
Parameters
[Display]
Settings
Initial
setting
Subwoofer levela)
[SW LEVEL]
SW –20.0 dB to SW +10.0 dB
(0.5 dB per step)
SW 0 dB
Dynamic range compression
[D. RANGE]
COMP. MAX, COMP. STD,
COMP. AUTO, COMP. OFF
COMP. AUTO
Speaker pattern
[SP PATTERN]
5/2.1 to 2/0
(20 patterns)
3/4.1
Front speakers sizea)
[FRT SIZE]
LARGE, SMALL
LARGE
Center speaker sizea)
[CNT SIZE]
LARGE, SMALL
LARGE
Surround speakers sizea)
[SUR SIZE]
LARGE, SMALL
LARGE
Front high speakers sizea)
[FH SIZE]
LARGE, SMALL
LARGE
Surround back speaker assignc)
[SB ASSIGN]
SPK B, BI-AMP, OFF
OFF
Front left speaker distancea)
[FL DIST.]
FL 3’3” to FL 32’9”
(FL 1.00 m to FL 10.00 m)
(1 inch (0.01 m) step)
FL 9’10”
(FL 3.00 m)
Front right speaker distancea)
[FR DIST.]
FR 3’3” to FR 32’9”
(FR 1.00 m to FR 10.00 m)
(1 inch (0.01 m) step)
FR 9’10”
(FR 3.00 m)
Center speaker distancea)
[CNT DIST.]
CNT 3’3” to CNT 32’9”
(CNT 1.00 m to CNT 10.00 m)
(1 inch (0.01 m) step)
CNT 9’10”
(CNT 3.00 m)
Surround left speaker distancea)
[SL DIST.]
SL 3’3” to SL 32’9”
(SL 1.00 m to SL 10.00 m)
(1 inch (0.01 m) step)
SL 9’10”
(SL 3.00 m)
Surround right speaker distancea) SR 3’3” to SR 32’9”
[SR DIST.]
(SR 1.00 m to SR 10.00 m)
(1 inch (0.01 m) step)
SR 9’10”
(SR 3.00 m)
Surround back speaker distancea) SB 3’3” to SB 32’9”
[SB DIST.]
(SB 1.00 m to SB 10.00 m)
(1 inch (0.01 m) step)
SB 9’10”
(SB 3.00 m)
Surround back left speaker
distancea)
[SBL DIST.]
SBL 3’3” to SBL 32’9”
(SBL 1.00 m to SBL 10.00 m)
(1 inch (0.01 m) step)
SBL 9’10”
(SBL 3.00 m)
Surround back right speaker
distancea)
[SBR DIST.]
SBR 3’3” to SBR 32’9”
(SBR 1.00 m to SBR 10.00 m)
(1 inch (0.01 m) step)
SBR 9’10”
(SBR 3.00 m)
Front left high speaker distancea) LH 3’3” to LH 32’9”
[LH DIST.]
(LH 1.00 m to LH 10.00 m)
(1 inch (0.01 m) step)
LH 9’10”
(LH 3.00 m)
RH 3’3” to RH 32’9”
(RH 1.00 m to RH 10.00 m)
(1 inch (0.01 m) step)
RH 9’10”
(RH 3.00 m)
Front right high speaker
distancea)
[RH DIST.]
124GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
Menu
[Display]
masterpage: Right
Parameters
[Display]
Settings
Initial
setting
Subwoofer distancea)
[SW DIST.]
SW 3’3” to SW 32’9”
(SW 1.00 m to SW 10.00 m)
(1 inch (0.01 m) step)
SW 9’10”
(SW 3.00 m)
Distance unit
[DIST. UNIT]
FEET, METER
FEETd)
Front speakers crossover
frequencye)
[FRT CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Center speaker crossover
frequencye)
[CNT CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Surround speakers crossover
frequencye)
[SUR CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Front high speakers crossover
frequencye)
[FH CROSS]
CROSS 40 Hz to CROSS 200 Hz
(10 Hz step)
CROSS 120 Hz
Surround settings Effect levelf)
[<SURROUND>] [EFFECT]
EFCT. 150%, EFCT. 100%,
EFCT. 80%, EFCT. 50%
EFCT. 100%
EQ settings
[<EQ>]
Front speakers bass level
[FRT BASS]
FRT B. –10.0 dB to FRT B. +10.0 dB FRT B. 0 dB
(0.5 dB step)
Front speakers treble level
[FRT TREBLE]
FRT T. –10.0 dB to FRT T. +10.0 dB FRT T. 0 dB
(0.5 dB step)
FM station receiving mode
[FM MODE]
STEREO, MONO
Naming preset stations
[NAME IN]
For details, see “Naming preset
stations (Name Input)” (page 64).
Sirius parental lockg)
[PARENTAL]
LOCK ON, LOCK OFF
Sirius lock code editg)
[CODE EDIT]
For details, see “Restricting access to 0000
specific channels (Parental Lock)”
(page 70).
Sirius antenna aimingg)
[SR ANT AIM]
For details, see “Checking receiving
conditions (Antenna Aiming)”
(page 67).
Sirius radio IDg)
[SIRIUS ID]
For details, see “Checking the ID
number” (page 66).
Tuner settings
[<TUNER>]
STEREO
LOCK OFF
Adjusting Settings
continued
125GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
Audio settings
[<AUDIO>]
Synchronizes audio with video
output
[A/V SYNC]
0 ms to 300 ms
(10 ms step)
0 ms
Digital broadcast language
selection
[DUAL MONO]
MAIN/SUB, MAIN, SUB
MAIN
Digital audio input decoding
priority
[DEC. PRIO]
DEC. AUTO, DEC. PCM
DEC. AUTO
Digital audio input assignment
[A. ASSIGN]
For details, see “Enjoying the sound/
images from other inputs (Input
Assign)” (page 104).
Resolution
[RESOLUTION]
DIRECT, AUTO, 480/576i,
480/576p, 720p, 1080i, 1080p
Video input assignment
[V. ASSIGN]
For details, see “Enjoying the sound/
images from other inputs (Input
Assign)” (page 104).
Control for HDMI
[CTRL: HDMI]
CTRL ON, CTRL OFF
CTRL ON
Pass Through
[PASS THRU]
ON, AUTO, OFF
OFF
Audio out
[AUDIO OUT]
AMP, TV+AMP
AMP
Subwoofer level for HDMIh)
[SW LEVEL]
SW AUTO, SW +10 dB, SW 0 dB
SW AUTO
Subwoofer Low Pass Filter for
HDMIh)
[SW L.P.F.]
L.P.F. ON, L.P.F. OFF
L.P.F. ON
S-AIR IDi)
[S-AIR ID]
ID: A, ID: B, ID: C
ID: A
S-AIR modei)
[S-AIR MODE]
PARTY, SEPARATE
PARTY
RF Changei)
[RF CHANGE]
RF AUTO, RF ON, RF OFF
RF AUTO
S-AIR Standbyi)
[S-AIR STBY]
STBY ON, STBY OFF
STBY OFF
Pairingi)
[PAIRING]
START, CONDITION
START
Video settings
[<VIDEO>]
HDMI settings
[<HDMI>]
S-AIR settings
[<S-AIR>]
AUTO
126GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
System settings
[<SYSTEM>]
Naming inputs
[NAME IN]
For details, see “Naming the input
(Name Input)” (page 55).
Auto standby mode
[AUTO STBY]
ON, OFF
ON
PERMIT, DENY
DENY
Version display
[VER. X.XXX]
Updating from PC
[UPDATE (PC)]
a) Depends
on the speaker pattern setting, some parameters or settings may not be available.
represent a speaker channel (FL, FR, CNT, SL, SR, SB, SBL, SBR, LH, RH, SW).
c)
You can only select this parameter if “SP PATTERN” is not set to a setting with surround back or front high
speakers (page 40).
d) “METER” for European model.
e)
You can only select this parameter if your speaker is set to “SMALL”.
f) You can only select this parameter if you select “C.ST.EX A”, “C.ST.EX B” or “C.ST.EX C” as sound field.
g) This parameter is available for the USA model only. You can only select this parameter if the SiriusConnect
Home tuner is connected to the SIRIUS jack on the receiver.
h) This parameter is only available when HDMI input is selected.
i) This parameter is only available if the S-AIR transmitter (not supplied) is inserted to the EZW-T100 slot on
the receiver.
b) xxx
To view the information on the
display
You can check the sound field, etc., by
changing the information on the display.
1 Select the input for which you want to
check the information.
2 Press AMP, then press DISPLAY
repeatedly.
Each time you press DISPLAY, the display
will change cyclically as follows.
When receiving RDS broadcasts
(European model only)
Program Service name3), Preset name,
Band, or Preset number t Frequency,
band and preset number t Program Type
indication4) t Radio Text indication5) t
Clock Time t Sound field currently
applied t Volume level
When listening to FM and AM radio
Preset station name1) t Frequency t
Sound field currently applied t Volume
level
continued
127GB
STR-DN2010
4-182-049-11(1)
Adjusting Settings
Index name of the input1) t Input you
selected t Sound field currently
applied t Volume level t Stream
information2)
When tuning in a channel from a
SIRIUS
(USA model only)
Channel name t Channel number t
Category name t Artist name/Feature t
Song/program title t Composer name t
Signal strength t Sound field currently
applied t Volume level
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Left
1)
Index name appears only when you have
assigned one to the input or preset station.
Index name does not appear when only blank
spaces have been entered or it is same as the
input name.
2)Stream information may not be displayed.
3)
This information also appears for non-RDS
FM stations.
4)Type of program being broadcast.
5)
Text messages sent by the RDS station.
Presetting radio stations
1
For details on the operation, see “Tuning
radio stations” (page 128).
2
Note
3
For details on the tuner function, see “Tuner
Operations” (page 61).
Tuning radio stations
1 Press TUNER repeatedly to select the
4
press D.TUNING.
2 Press SHIFT, then press numeric
buttons to enter the frequency.
3 Press
.
Press ENTER.
If SHIFT indicator is light off before you
press ENTER, press SHIFT.
The station is stored as the selected preset
number.
If “MEM” disappears before you press
ENTER, start again from step 2.
2 Press TUNING + or TUNING –.
Selecting a frequency directly
(Direct Tuning)
1 After selecting the FM or AM band,
Press PRESET + or PRESET –
to select a preset number.
30 FM and 30 AM preset numbers are
available. If “MEM” disappears before
you select the preset number, start again
from step 2.
FM or AM band.
You can also use INPUT SELECTOR +/–
on the receiver.
Press TUNING + to scan from low to high
frequencies, press TUNING – to scan from
high to low frequencies. The receiver stops
scanning whenever a station is received.
Press SHIFT, then press
MEMORY.
“MEM” lights up for a few seconds.
Perform steps 3 and 4 before “MEM”
disappears.
Character or marks may not be displayed for some
languages.
Listening to the FM/AM radio
Tune in the station that you
want to preset.
5
Repeat steps 1 to 4 to preset
another station.
Selecting a preset station
1 Press TUNER repeatedly to select the
FM or AM band.
2 Press PRESET + or PRESET –
repeatedly to select the preset station
you want.
You can also press SHIFT, then press
numeric buttons to select the preset station
you want. Then, press
to enter the
selection.
128GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB05ENJ_STR-DN2010-CEL.fm
masterpage: Right
Checking the ID number
1 Press TUNER repeatedly to select
Listening to satellite radio
(USA model only)
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
For details on SIRIUS Radio service, see
“Listening to Satellite Radio” (page 65) in
“Tuner Operations”.
2 Press TUNING + or TUNING – to select
Aiming the SIRIUS Antenna
3 Check the SIRIUS ID on the display
You can use “SR ANT AIM” in the Tuner
Settings menu to help you aim the antenna for
optimal signal reception.
1 Press TUNER repeatedly to select
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
2 Press AMP.
3 Press MENU.
“<TUNER>”.
or b to enter the menu.
6 Press V/v repeatedly to select
“SR ANT AIM”.
7 Press
or b to enter the parameter.
8 While checking the parameter, aim
your antenna to where the best
reception will be received.
For details on the parameter, see “SIRIUS
Signal strength” below.
Selecting channels from a
category (CATEGORY TUNING)
1 Press TUNER repeatedly to select
“SIRIUS”.
You can also use INPUT SELECTOR +/–
on the receiver.
to select “ONE CAT”.
• ALL CAT: You can select a channel from
all the categories. The initial setting is
“ALL CAT”.
• ONE CAT: You can select a channel from
one category. “CAT” lights up on the
display when you set to “ONE CAT”
mode.
3 Press CATEGORY + or CATEGORY –
to select the category you want.
The category is selected and the channel
with the lowest number in the specified
category is selected.
4 Press TUNING + or TUNING – to select
SIRIUS Signal strength
the channel.
Signal type
Satellite
Terrestrial
EXC (excellent)
S:3
T:3
GOOD
S:2
T:2
WEAK
S:1
T:1
NONE
S:0
T:0
Selecting a channel number
directly (Direct Tuning)
1 After selecting satellite tuner, press
D.TUNING.
2 Press SHIFT, then press numeric
buttons to enter the channel number.
3 Press
.
129GB
STR-DN2010
4-182-049-11(1)
Adjusting Settings
Signal
strength
and write it in the space provided here.
SIRIUS ID:___________________________
2 Press CATEGORY MODE repeatedly
4 Press V/v repeatedly to select
5 Press
channel 0.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB06REM_STR-DN2010-CEL.fm
Presetting satellite radio
channels
(USA model only)
1
Select a channel you want to
preset.
For details on this operation, see
“Selecting channels from a category
(CATEGORY TUNING)” (page 129).
2
Press SHIFT, then press
MEMORY.
“MEM” lights up on the display.
3
Press PRESET + or PRESET –
to select a preset number.
You can also select the number by
pressing SHIFT, then numeric buttons.
Preset numbers from 1 to 30 are available.
Channel 1 is initial setting for the preset
numbers when you purchase the receiver.
4
Using the Remote
Programming the remote
You can customize the remote to match the
components connected to your receiver. You
can even program the remote to control nonSony components and also Sony components
that the remote is normally unable to control.
Before you begin, note that:
– You cannot change the settings of TUNER
and DMPORT input buttons.
– The remote can control only components
that accept infrared wireless control signals.
Be sure to turn on the receiver and
point the remote towards the
receiver when performing the
following procedure.
RM
SET UP
Press ENTER.
SHIFT
If SHIFT indicator is light off before you
press ENTER, press SHIFT.
“MEM” lights off.
5
“SIRIUS”.
TV
Input
buttons
ENTER
1
2 Press PRESET + or PRESET –
repeatedly to select the preset channel
you want.
You can also press SHIFT, then numeric
buttons to select the preset channel you
want. Then, press
to enter the selection.
AV ?/1
Numeric
buttons
Repeat steps 1 to 4 to preset
another channel.
Selecting a preset channel
1 Press TUNER repeatedly to select
masterpage: Left
Press and hold RM SET UP,
then press AV ?/1.
The RM SET UP indicator flashes slowly.
2
Press the input button for the
component you want to control.
For example, if you are going to control a
VCR connected to VIDEO 1 jacks, press
VIDEO 1.
The RM SET UP and SHIFT indicator
light up.
130GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB06REM_STR-DN2010-CEL.fm
3
Press numeric buttons to enter
the numeric code (or one of the
codes if more than one code
exists) corresponding to the
component and the maker of
the component you want to
control (including TV button).
See the tables on page 132–134 for
information on the numeric code(s).
Note
For a TV remote code value, only numbers in
the 500’s are valid.
4
Press ENTER.
Once the numeric code has been verified,
the RM SET UP indicator slowly flashes
twice and the remote automatically exits
the programming mode.
5
Repeat steps 1 to 4 to control
other components.
Notes
• The indicator turns off while a valid button is
pressed.
• For the numeric codes, only the last three numbers
entered are valid.
To cancel programming
Press RM SET UP during any step. The
remote automatically exits the programming
mode.
masterpage: Right
If programming is
unsuccessful, check the
following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 5 times in quick
succession while entering the numeric code,
an error has occurred.
Start again from step 1.
The numeric codes
corresponding to the component
and the maker of the component
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than
one numeric code may be assigned to a
component. If you fail to program your remote
using one of the codes, try using other codes.
Notes
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
• All of the input buttons on this remote may not be
available when used with your particular
component.
To activate the input after
programming
Press the programmed button to activate the
input you want.
Using the
Remote
continued
131GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB06REM_STR-DN2010-CEL.fm
masterpage: Left
To control a CD player
To control an HDD recorder
Maker
Code(s)
SONY
101, 102, 103
Maker
SONY
DENON
104, 123
JVC
105, 106, 107
KENWOOD
108, 109, 110
To control a Blu-ray Disc player/
recorder
MAGNAVOX
111, 116
Maker
Code(s)
MARANTZ
116
SONY
310, 311, 312
ONKYO
112, 113, 114
PANASONIC
335
PANASONIC
115
SAMSUNG
336
PHILIPS
116
LG
337
PIONEER
117
Code(s)
307, 308, 309
TECHNICS
115, 118, 119
To control a PSX
YAMAHA
120, 121, 122
Maker
Code(s)
SONY
313, 314, 315
To control a DAT deck
Maker
Code(s)
To control a DVD player
SONY
203
Maker
Code(s)
PIONEER
219
SONY
401, 402, 403
BROKSONIC
424
To control a tape deck
DENON
405
Maker
Code(s)
HITACHI
416
SONY
201, 202
JVC
415, 423
DENON
204, 205
MITSUBISHI
419
KENWOOD
206, 207, 208, 209
ORITRON
417
NAKAMICHI
210
PANASONIC
406, 408, 425
PANASONIC
216
PHILIPS
407
PHILIPS
211, 212
PIONEER
409, 410
PIONEER
213, 214
RCA
414
TECHNICS
215, 216
SAMSUNG
416, 422
YAMAHA
217, 218
TOSHIBA
404, 421
ZENITH
418, 420
To control an MD deck
Maker
Code(s)
To control a DVD recorder
SONY
301
Maker
Code(s)
DENON
302
SONY
401, 402, 403
JVC
303
KENWOOD
304
To control a DVD/VCR COMBO
Maker
Code(s)
SONY
411
132GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB06REM_STR-DN2010-CEL.fm
masterpage: Right
To control a DVD/HDD COMBO
Maker
Code(s)
Maker
Code(s)
PIONEER
SONY
401, 402, 403
509, 525, 526, 540,
551, 555
PORTLAND
503
To control a TV
Maker
QUASAR
509, 535
RADIO SHACK
503, 510, 527, 565,
567
RCA/PROSCAN
503, 510, 523, 529,
544
SAMSUNG
503, 515, 517, 531,
532, 534, 544, 556,
557, 562, 563, 566,
569
Code(s)
SONY
501, 502
AIWA
501, 536, 539
AKAI
503
AOC
503
CENTURION
566
CORONADO
517
SAMPO
566
CURTIS-MATHES
503, 551, 566, 567
SABA
DAYTRON
517, 566
530, 537, 547, 549,
558
DAEWOO
504, 505, 506, 507,
515, 544
SANYO
508, 545, 546, 560,
567
FISHER
508, 545
FUNAI
548
FUJITSU
528
GOLDSTAR/LG
503, 512, 515, 517,
534, 544, 556, 568
GRUNDIG
511, 533, 534
HITACHI
503, 513, 514, 515,
517, 519, 544, 557,
571
ITT/NOKIA
521, 522
SCOTT
503, 566
SEARS
503, 508, 510, 517,
518, 551
SHARP
517, 535, 550, 561,
565
SYLVANIA
503, 518, 566
THOMSON
530, 537, 547, 549
TOSHIBA
535, 539, 540, 541,
551
TELEFUNKEN
530, 537, 538, 547,
549, 558
TEKNIKA
517, 518, 567
J.C.PENNY
503, 510, 566
JVC
516, 552
KMC
517
MAGNAVOX
503, 515, 517, 518,
544, 566
ZENITH
542, 543, 567
MARANTZ
527
GE
503, 509, 510, 544
MITSUBISHI/MGA
503, 519, 527, 544,
566, 568
LOEWE
515, 534, 556
NEC
503, 517, 520, 540,
544, 554, 566
NORDMENDE
530, 558
NOKIA
521, 522, 573, 575
PANASONIC
509, 524, 553, 559,
572
PHILIPS
515, 518, 557, 570,
571
PHILCO
503, 504, 514, 517,
518
WARDS
503, 517, 566
YORK
566
To control an LD player
Maker
Code(s)
601, 602, 603
PIONEER
606
To control a Video CD player
Maker
Code(s)
SONY
605
Using the
Remote
SONY
continued
133GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB06REM_STR-DN2010-CEL.fm
To control a VCR
masterpage: Left
To control a satellite tuner (box)
Maker
Code(s)
Maker
Code(s)
SONY
701, 702, 703, 704,
705, 706
SONY
801, 802, 803, 804,
824, 825, 865
AIWA*
710, 750, 757, 758
AMSTRAD
845, 846
AKAI
707, 708, 709, 759
BskyB
862
BLAUPUNKT
740
711, 712, 713, 714,
715, 716, 750
GENERAL ELECTRIC
(GE)
866
EMERSON
GRUNDIG
859, 860
FISHER
717, 718, 719, 720
HUMAX
846, 847
GENERAL ELECTRIC
(GE)
721, 722, 730
THOMSON
857, 861, 864, 876
PACE
GOLDSTAR/LG
723, 753
848, 849, 850, 852,
862, 863, 864
HITACHI
722, 725, 729, 741
PANASONIC
818, 855
ITT/NOKIA
717
PHILIPS
JVC
726, 727, 728, 736
856, 857, 858, 859,
860, 864, 874
MAGNAVOX
730, 731, 738
NOKIA
851, 853, 854, 864
MITSUBISHI/MGA
732, 733, 734, 735
RCA/PROSCAN
866, 871
NEC
736
BITA/HITACHI
868
729, 730, 737, 738,
739, 740
HUGHES
867
873
PANASONIC
PHILIPS
729, 730, 731
JVC/Echostar/Dish
Network
PIONEER
729
MITSUBISHI
872
RCA/PROSCAN
722, 729, 730, 731,
741, 747
SAMSUNG
875
TOSHIBA
869, 870
SAMSUNG
742, 743, 744, 745
SANYO
717, 720, 746
SHARP
748, 749
TOSHIBA
747, 756
ZENITH
754
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
To control a cable box
Maker
Code(s)
SONY
821, 822, 823
HAMLIN/REGAL
836, 837, 838, 839,
840
JERROLD/G.I./
MOTOROLA
806, 807, 808, 809,
810, 811, 812, 813,
814, 819
JERROLD
830, 831
OAK
841, 842, 843
PANASONIC
816, 826, 832, 833,
834, 835
PHILIPS
830, 831
PIONEER
828, 829
RCA
805
SCIENTIFIC ATLANTA 815, 816, 817, 844
TOCOM/PHILIPS
830, 831
ZENITH
826, 827
134GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
Clearing all the contents
of the remote’s memory
1 While holding down MASTER
VOL – (RM-AAP055 only) or
2 – (RM-AAP056 only), press
and hold ?/1, then press
AV ?/1.
The RM SET UP indicator flashes 3
times.
2
masterpage: Right
Additional Information
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
On power sources
All the contents of the remote’s memory
(i.e., all the programmed data) are
cleared.
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
• (USA model only)
One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
• The AC power cord (mains lead) must be
changed only at a qualified service shop.
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
continued
135GB
STR-DN2010
4-182-049-11(1)
Additional Information
Release all buttons.
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
masterpage: Left
On placement
On S-AIR function
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
• Do not place the receiver near equipment
such as a TV, VCR, or tape deck. (If the
receiver is being used in combination with a
TV, VCR, or tape deck, and is placed too
close to that equipment, noise may result,
and picture quality may suffer. This is
especially likely when using an indoor
antenna (aerial). Therefore, we recommend
using an outdoor antenna (aerial).)
• Use caution when placing the receiver on
surfaces that have been specially treated
(with wax, oil, polish, etc.) as staining or
discoloration of the surface may result.
• As the S-AIR product(s) transmits sound by
radio waves, sound may skip when radio
waves are obstructed. This is a characteristic
of radio waves and is not malfunction.
• As the S-AIR product(s) transmits sound by
radio waves, equipment that generates
electromagnetic energy, such as a
microwave oven, may prevent sound
transmission.
• As the S-AIR function uses the radio waves
that share the same frequency as other
wireless systems, such as wireless LAN or
Bluetooth devices, interference or poor
transmission may result. In this case, take
the following steps:
– Avoid placing the S-AIR product(s) near
other wireless systems.
– Avoid using the S-AIR product(s) and the
other wireless systems spontaneously.
– The transmission may be improved by
changing the transmission channel
(frequency) of the other wireless
system(s). For details, refer to the
operating instructions of the other wireless
system(s).
• The transmission distance differs depending
on the usage environment. Find a location
where transmission between the S-AIR main
unit and sub unit is most effective, and install
the S-AIR main unit and sub unit there.
• Place the S-AIR product(s) on the stable
surface off the floor.
• Poor transmission may occur and the
transmission distance may be too short if the
following conditions exist:
– There is a wall/floor made of reinforced
concrete or stone between the S-AIR
product(s).
– There is an iron divider/door or furniture/
electric product made of fireproof glass,
metal, etc., between the S-AIR product(s).
On operation
Before connecting other components, be sure
to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
136GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
General
The receiver is turned off
automatically.
• “Auto Standby” is set to “ON” (page 121).
• The Sleep Timer function is working
(page 59).
Audio
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is no sound from a specific
component.
• Check that the component is connected
correctly to the audio input jacks for that
component.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
component.
• Set the INPUT MODE to “AUTO”
(page 103).
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
• Make sure you have connected to both the
L and R jacks of an analog component, and
not only to either the L or R jack. Use an
audio cord (not supplied). However, there
will be no sound from the center speaker
when a sound field (2ch Stereo, etc.) is
selected. When the center speaker is not
connected, sound is output only from the
front left/right speakers.
There is no sound from analog 2
channel sources.
• Check that the selected digital audio input
jack is not assigned to other inputs in
“Input Assign” in the Input Option menu
(page 104).
continued
137GB
STR-DN2010
4-182-049-11(1)
Additional Information
There is no sound, no matter which
component is selected, or only a very
low-level sound is heard.
• Check that the speakers and components
are connected securely.
• Check that all speaker cords are connected
correctly.
• Check that both the receiver and all
components are turned on.
• Check that MASTER VOLUME control is
not set to “VOL MIN”.
• Check that the SPEAKERS is not set to
“SPK OFF” (page 42).
• Check that headphones are not connected
to the receiver or S-AIR surround
amplifier.
• Press MUTING (RM-AAP055 only) or
(RM-AAP056 only) on the remote to
cancel the muting function.
• Check that you have selected the correct
component with the input buttons
(page 54).
• Check to see if NIGHT MODE is activated
(page 77).
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
There is no sound from digital sources
(from COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
“ANALOG” (page 103).
• Check that the “A. DIRECT” is not being
used.
• Check that the selected digital audio input
jack is not assigned to other inputs in
“Input Assign” in the Input Option menu
(page 104).
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the level parameters using the
Speaker Settings menu.
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
10 feet (3 meters) away from a TV set or
fluorescent light.
• Move your audio components away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
There is no sound, or only a very lowlevel sound is heard from the center/
surround/surround back/front high
speakers.
• Select a Cinema Studio EX mode (page
73, 74).
• Adjust the speaker level (page 110).
• Make sure the center/surround speaker (s)
is (are) set to either “Small” or “Large”.
• Check that the speaker settings are
appropriate using the Auto Calibration
menu or “Speaker Pattern” in the Speaker
Settings menu. Then check that sound is
output from each speaker correctly, using
“Test Tone” in the Speaker Settings menu.
masterpage: Left
There is no sound from the surround
back speakers.
• Some discs have no Dolby Digital
Surround EX flag even though the
packages have Dolby Digital Surround EX
logos.
• Check the “Speaker Pattern” setting
(page 40).
There is no sound from the subwoofer.
• Check that the subwoofer is connected
correctly and securely.
• Make sure you have turned on your
subwoofer.
• Depending on the selected sound field, no
sound output from the subwoofer.
• When all speakers are set to “Large” and
“Neo:6 CIN” or “Neo:6 MUS” is selected,
there is no sound from the subwoofer.
• Check the “Speaker Pattern” setting
(page 40).
The surround effect cannot be
obtained.
• Make sure you have selected the sound
field for movie or music (page 73 or 74).
• Sound fields do not function for signals
with a sampling frequency of more than
48 kHz.
Dolby Digital or DTS multi channel
sound is not reproduced.
• Check that the DVD, etc. you are playing
is recorded in Dolby Digital or DTS
format.
• When connecting the DVD player, etc., to
the digital input jacks of this receiver,
make sure the setting for the digital audio
output of the connected component is
available. For example, when connecting
the “PlayStation 3”, set the BD/DVD
audio output format to “Bitstream” on the
“PlayStation 3”.
• Set “Audio Out” to “AMP” in the HDMI
Settings menu.
138GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 54).
The MULTI CHANNEL DECODING
indicator does not light up in blue.
• Check that the playback component is
connected to a digital jack and the input is
selected properly on this receiver.
• Check whether the input source of the
software being played back corresponds to
the multi channel format.
• Check whether the setup on the playback
component is set to multi channel sound.
• Check to make sure the selected digital
audio input jack is not assigned to other
inputs in “Input Assign” in the Input
Option menu (page 104).
There is no sound from the component
connected to the DIGITAL MEDIA PORT
adapter.
• Adjust the volume of this receiver.
• The DIGITAL MEDIA PORT adapter
and/or component is not connected
correctly. Turn off the receiver, then
reconnect the DIGITAL MEDIA PORT
adapter and/or component.
• Check the DIGITAL MEDIA PORT
adapter and/or component device to make
sure it supports this receiver.
masterpage: Right
• The input signal should be same as the
input function when you are up-converting
an input signal with this receiver
(page 33).
• Depending on the DIGITAL MEDIA
PORT adapter, video output may not be
possible.
• When you use an HDMI-DVI conversion
cable for the connection, the image may
not be output correctly.
The image of the COMPONENT VIDEO
MONITOR OUT is corrupted.
• The resolution of output signals from the
COMPONENT VIDEO MONITOR OUT
jacks may not be supported by your TV. In
this case, select the appropriate resolution
on the receiver (page 116).
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 54).
The GUI menu does not appear on the
TV screen.
• Press GUI MODE repeatedly to select
“GUI ON”. If the GUI menu still does not
appear on the TV screen, press MENU.
• Check that the TV is connected correctly.
Video
There is no picture or an unclear
picture appears on the TV screen or
monitor.
• Select the appropriate input using the input
buttons.
• Set your TV to the appropriate input mode.
• Move your audio components away from
the TV.
• Assign the component video input
correctly.
The source sound input from the HDMI
IN jack on the receiver is not output
from the speakers connected to the
receiver or TV speaker.
• Check the setting of “Audio Out” in the
HDMI Settings menu (page 117).
• Check that the component is connected
correctly to the HDMI jack for that
component.
• You cannot listen to the Super Audio CD
by connecting HDMI.
continued
139GB
STR-DN2010
4-182-049-11(1)
Additional Information
HDMI
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
• Be sure to use a High Speed HDMI cable
when you view images or listen to sound
during a 1080p, Deep Color (Deep Colour)
or 3D transmission.
• Sound may not be output from the receiver
while the GUI appears on the TV screen.
Press GUI MODE to select “GUI OFF”.
Images from the component connected
to the HDMI jack are not output to the
TV, are distorted, or are interrupted.
• Make sure that cables are correctly and
securely connected to components.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
• Be sure to use a High Speed HDMI cable
when you view images or listen to sound
during a 1080p, Deep Color (Deep Colour)
or 3D transmission.
No 3D image appears on the TV.
• Depending on the TV or the video
component, 3D images may not be
displayed. Check the 3D image formats
supported by the system (page 146).
The Control for HDMI function does not
work.
• Check the HDMI connection (page 25).
• Make sure “Control for HDMI” is set to
“ON” in HDMI Settings menu.
• Make sure the connected component is
compatible with the Control for HDMI
function.
• Check the Control for HDMI settings on
the connected component. Refer to the
operating instructions of the connected
component.
• When “Control for HDMI” is set to
“OFF”, the “BRAVIA” Sync does not
work properly, even if a component is
connected to the HDMI IN jack.
masterpage: Left
• The types and the number of components
which can be controlled by the
“BRAVIA” Sync are restricted in the
HDMI CEC standard as follows.
– Recording component (Blu-ray Disc
recorder, DVD recorder, etc.): up to 3
components
– Playback component (Blu-ray Disc
player, DVD player, etc.): up to 3
components
– Tuner-related component: up to 4
components
– AV receiver (audio system): up to 1
component
No sound is output from the receiver
and TV speaker while using the System
Audio Control function.
• Make sure the TV is compatible with the
System Audio Control function.
• If the TV does not have System Audio
Control function, set the “Audio Out”
settings in HDMI Settings menu to
– “TV+AMP” if you want to listen to the
sound from the TV speaker and
receiver.
– “AMP” if you want to listen to the
sound from the receiver.
• When you connect the receiver to a video
component (projector, etc.), sound may
not be output from the receiver. In this
case, select “AMP”.
• If you cannot listen to the sound of a
component connected to the receiver
while TV input is selected on the receiver
– Change the input of the receiver to
HDMI when you want to watch a
program on a component connected via
HDMI connection to the receiver.
– Change the TV channel when you want
to watch a TV broadcast.
– Select the component or input you want
to watch when you watch a program on
the component connected to the TV.
Refer to the operating instructions of the
TV on this operation.
140GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
The TV’s remote cannot be used to
control the connected component
when using the Control for HDMI
function.
• Depending on the connected component
and TV, you may need to set up the
component and TV. Refer to the operating
instructions supplied with each component
and TV.
• Change the input of the receiver to the
HDMI input connected to the component.
When the receiver is in standby mode,
there is no image or sound output from
the TV.
• When the receiver is in standby mode,
image and sound are output from the
HDMI component selected the last time
you turned off the receiver. If you are
enjoying other component, play the
component and perform the One-Touch
Play operation, or turn on the receiver to
select the HDMI component you want to
enjoy.
• Make sure “Pass Through” is set to “ON”
in the HDMI Settings menu if you connect
components not compatible with the
“BRAVIA” Sync to the receiver (page
117).
S-AIR function
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• The S-AIR sub unit is turned off. Make
sure the AC power cord (mains lead) is
connected and turn on the S-AIR sub unit.
No sound is heard from the S-AIR
receiver.
• Check that the components are connected
to the receiver.
No sound is heard from the S-AIR
product.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Confirm the ID of the S-AIR main unit and
S-AIR sub unit are the same (page 95).
• Confirm the pairing setting (page 96).
• Place the S-AIR main unit and S-AIR sub
unit closer to each other.
• Avoid using the equipment that generates
electromagnetic energy, such as a
microwave oven.
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• Change the “RF Change” setting (page
100).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit,
then turn them on again.
• Check that headphones are not connected
to the S-AIR sub unit.
There is noise or the sound skips.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Sources with copyright protection may not
be playable on S-AIR sub unit.
• Place the S-AIR main unit and S-AIR sub
unit closer to each other.
continued
141GB
STR-DN2010
4-182-049-11(1)
Additional Information
S-AIR connection is not established
(sound transmission is not
established), e.g., the indicator of the
S-AIR sub unit turns off, flashes, or
turns red.
• If you use another S-AIR main unit, place
it more than 26 feet (8 meters) away from
this S-AIR main unit.
• Confirm the S-AIR IDs of the S-AIR main
unit and S-AIR sub unit are the same
(page 95).
• Another S-AIR sub unit is paired to the
S-AIR main unit. Pair the S-AIR sub unit
you want with the S-AIR main unit
(page 96).
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
• Avoid using the equipment that generates
electromagnetic energy, such as a
microwave oven.
• Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
• Avoid using any other wireless devices.
• Change the “RF Change” setting (page
100).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
“HP NO LINK” and “VOL MIN” appear
alternately on the display and the
volume of the receiver becomes
minimum.
• Volume becomes minimum when you turn
off the surround amplifier with
headphones connected or if the radio
reception is poor. In these cases, check the
radio reception and adjust the volume
level to restore sound from the
headphones.
Tuner
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antennas (aerial) as shown below. If you
connect the receiver to an outdoor antenna
(aerial), ground it against lightning. To
prevent a gas explosion, do not connect the
ground (earth) wire to a gas pipe.
Outdoor FM antenna (aerial)
Receiver
Ground
(earth) wire
(not supplied)
masterpage: Left
Radio stations cannot be tuned in.
• Check that the antennas (aerials) are
connected securely. Adjust the antennas
(aerials) and connect an external antenna
(aerial), if necessary.
• Keep the satellite radio antenna, away
from the speaker cords and the power cord
to avoid picking up noise.*
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning). Use direct tuning.
• Make sure you set the tuning interval
correctly (when tuning in AM stations
with direct tuning).
• No stations have been preset or the preset
stations have been cleared (when tuning
by scanning preset stations). Preset the
stations (page 63).
• Press AMP, then press DISPLAY
repeatedly on the remote so that the
frequency appears on the display.
The receiver cannot receive satellite
channels at all.*
• The receiving condition is not good. Move
the antenna to the place where the
condition is good.
• Check that you subscribed to the satellite
radio service you want (page 65).
RDS does not work.**
• Make sure that you are tuned to an FM
RDS station.
• Select a stronger FM station.
The RDS information that you want
does not appear.**
• Contact the radio station and find out
whether they actually provide the service
in question. If so, the service may be
temporarily out of order.
* USA model only.
**European model only.
To ground
142GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
Remote commander
The remote does not function.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure you select the correct input on
the remote.
• When you operate a programmed nonSony component, the remote may not
function properly depending on the model
and the maker of the component.
Network
Cannot find or play back the content on
the server.
• On the “ Music”, “ Photo”, and
“
Video” screens, the receiver displays
only the content that can be played back
with the receiver from among the content
offered by the server within the DLNA
guidelines.
• The content without a [*] mark before the
name is offered by the server as that
defined in the DLNA guidelines, and it can
be played back with the receiver.
The content with a [*] mark before the
name is offered by the server as that not
defined in the DLNA guidelines, and it
may be played back with the receiver.
• There may be content that is not displayed
even if it can be played back with the
receiver because it is not defined in the
DLNA guidelines. However, the receiver
may not be able to play back the content,
even if it is defined in the DLNA
guidelines.
• The availability of certain content may
differ, depending on the server software. If
the content is not displayed or cannot be
played back, try the supplied VAIO Media
plus application software as your server
software.
Cannot connect to the receiver with the
Setup Manager application software.
• Does antivirus software, firewall software,
or a network packet filter driver run on
your computer?
Deactivate such software temporarily, or
change the settings to accept all incoming
TCP or UDP packets from the receiver.
Cannot access the receiver from the
network controller.
• Make sure “External Control” is set to
“ON” in Network Settings menu.
continued
143GB
STR-DN2010
4-182-049-11(1)
Additional Information
Cannot find the server.
• Search the server using the
“ServerSearch” function (page 79).
• Check the following:
– Is the router turned on?
– If there is another device between this
device and the router, check that device
is turned on.
– Are all of the cables connected correctly
and securely?
– Is the settings to make sure that they
match the router’s settings (DHCP or
fixed IP address)?
• When using a computer, check the
following:
– The built-in firewall settings for the
computer’s operating system.
– The firewall settings of your security
software. To check the firewall settings
of your security software, refer to your
security software’s Help section.
• Register this device with the server. For
details, refer to the operating instructions
supplied with the server.
• Wait for a few moments, and then try
connecting to the server again.
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
• Is the network controller listed on the
Controllers settings screen, and is the box
for “Permit” checked?
If the box is not checked, check the box for
“Auto Permission”, and return to the
menu. Then, operate the receiver using the
network controller once, and then uncheck
the box for “Auto Permission”.
• If the network controller is a computer
software controller, is the software filtered
by antivirus software or firewall software?
Permit UPnP communications between
the software and the receiver.
• Network controllers could be listed up to
10 on the “Controllers”. If the network
controller does not listed, remove some of
controller(s) and try again.
If the trouble is other than one of the cases
described above and the trouble is not solved
even if you wait for a while, perform either of
the operations below.
• Press ?/1 on the remote to turn the
receiver off and then on again.
• Hold down ?/1 on the receiver until the
white indicator flashes to reboot the
receiver.
masterpage: Left
For other messages, see “Message list after
Auto Calibration measurement” (page 48),
“DIGITAL MEDIA PORT message list”
(page 58) and “Satellite radio message list”
(page 72).
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
In the event of a problem with S-AIR function,
have a Sony dealer check the entire system
together (S-AIR main unit and S-AIR sub
unit).
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
page 39
Customized sound fields
page 77
About support information
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
Refer to the following web site for details of
the latest information on the receiver.
For customers in the United States:
http://www.sony.com/essupport
For customers in Europe:
http://support.sony-europe.com/quickjump/
STR
144GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(USA model only)
With 8 ohm loads, both channels driven, from
20 Hz – 20,000 Hz; rated 100 watts per
channel minimum RMS power, with no more
than 0.09% total harmonic distortion from
250 milliwatts to rated output.
Amplifier section
USA model1)
Minimum RMS Output Power
(8 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
110 W + 110 W
Surround Mode Output Power2)
(8 ohms, 1 kHz, THD 10%)
150 W per channel
European model1)
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
100 W + 100 W
Surround Mode Output Power2)
(8 ohms, 1 kHz, THD 10%)
140 W per channel
3) INPUT
SHORT (with sound field and equalizer
bypassed).
4) Weighted network, input level.
FM tuner section
Tuning range
87.5 MHz – 108.0 MHz
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Area
Tuning scale
10 kHz step
9 kHz step
USA
530 kHz –
1,710 kHz
531 kHz –
1,710 kHz
Europe
–
531 kHz –
1,602 kHz
Measured under the following conditions:
Area
Power requirements
USA
120 V AC, 60 Hz
Europe
230 V AC, 50 Hz
2)
Frequency response
Analog
10 Hz – 70 kHz,
+0.5 dB/–2 dB (with sound
field and equalizer
bypassed)
Input
Analog
Sensitivity: 500 mV/
50 kohms
S/N3): 96 dB
(A, 500 mV4))
Digital (Coaxial) Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
Digital (Optical) S/N: 100 dB
(A, 20 kHz LPF)
Output (Analog)
AUDIO OUT
Voltage: 500 mV/10 kohms
SUBWOOFER
Voltage: 2 V/1 kohm
Equalizer
Gain levels
±10 dB, 0.5 dB step
Reference power output for front, center,
surround, surround back and front high speakers.
Depending on the sound field settings and the
source, there may be no sound output.
Antenna (aerial)
Loop antenna (aerial)
Intermediate frequency
450 kHz
continued
145GB
STR-DN2010
4-182-049-11(1)
Additional Information
1)
masterpage: Right
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
masterpage: Left
Video section
Supported playback formats
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
Content delivered from the device on the home
network needs to support the following formats
for you to play back content on this receiver.
Type of
content
Format
Other conditions
Music
Linear
PCM
LPCM defined in DLNA
guidelines 1.0
Sampling Rate: 44.1 kHz,
48 kHz
Channels: 1, 2
Quantization: 16 bit
MPEG-1
Layer 3
(MP3)
MPEG defined in DLNA
guidelines 1.0
Bitrate: 32, 40, 48, 56, 64,
80, 96, 112, 128, 160,
192, 224, 256, 320 kbps
Sampling Rate: 32 kHz,
44.1 kHz, 48 kHz
Channels: 1, 2
Encoding: CBR, VBR
Windows
Media
Audio
(WMA)
WMA_FULL and
WMA_BASE defined in
DLNA guidelines 1.0
Maximum Bitrate:
385 kbps
Sampling Rate: up to
48 kHz
Channels: 2
Not compatible with
WMA Pro files.
AAC
AAC_ISO defined in
DLNA guidelines 1.0
AAC Profile @ Level 1,
@ Level 2
Sampling Rate: 8, 11.025,
12, 16, 22.05, 24, 32, 44.1,
48 kHz
Maximum Bitrate:
576 kbps
Channels: 1, 2
Some files may not be
played back.
WAV
Conforms to Linear PCM.
Some files may not be
played back.
HDMI Video
Input/Output (HDMI Repeater block)
640 × 480p@60 Hz
720 × 480p@59.94/60 Hz
1280 × 720p@59.94/60 Hz
1920 × 1080i@59.94/60 Hz
1920 × 1080p@59.94/60 Hz
720 × 576p@50 Hz
1280 × 720p@50 Hz
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
HDMI Video (3D)
Input/Output (HDMI Repeater block)
1280 × 720p@59.94/60 Hz Frame packing
1280 × 720p@59.94/60 Hz Top-and-Bottom
1920 × 1080i@59.94/60 Hz Frame packing
1920 × 1080i@59.94/60 Hz Side-by-Side (Half)
1920 × 1080p@59.94/60 Hz Side-by-Side (Half)
1280 × 720p@50 Hz Frame packing
1280 × 720p@50 Hz Top-and-Bottom
1920 × 1080i@50 Hz Frame packing
1920 × 1080i@50 Hz Side-by-Side (Half)
1920 × 1080p@50 Hz Side-by-Side (Half)
1920 × 1080p@24 Hz Frame packing
1920 × 1080p@24 Hz Top-and-Bottom
146GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB07ADD_STR-DN2010-CEL.fm
masterpage: Right
Type of
content
Format
Other conditions
Notes
Photo
JPEG
JPEG_SM, JPEG_MED,
or JPEG_LRG defined in
DLNA guidelines 1.0
Maximum Resolution:
4096 × 4096
Non-progressive JPEG
BMP
Conforms to JPEG.
Some files may not be
played back.
• Not compatible with DRM protected files.
• Depending on the files, there may be files that
sometimes cannot be played back, even if they
meet the requirements described above.
• Concerning the formats defined in the DLNA
guidelines, the server is required to offer the
content to which the format information defined in
the DLNA guidelines has been added properly.
PNG
Conforms to JPEG.
Some files may not be
played back.
Video
MPEG-2
(NTSC)
MPEG-2
(PAL)
MPEG_PS_PAL defined
in DLNA guidelines 1.0
Maximum Resolution:
720 × 576
Maximum System Bitrate:
10.08 Mbps
Maximum Bitrate*
CBR: 9.80 Mbps/VBR:
9.80 Mbps
* Bitrate is mixed with
MPEG-1 Layer 1/2/3,
PCM, or AC3 audio
format.
Maximum Resolution:
720 × 480
Maximum Bitrate:
2 Mbps
Windows Media Video
7/8/9 standard definition
for Main profile mixed
with Windows Media
Video 7/8/9 excludes all
profile of Windows Media
Audio professional.
Some files may not be
played back.
Power requirements
Area
Power requirements
USA
120 V AC, 60 Hz
Europe
230 V AC, 50/60 Hz
Power output (DIGITAL MEDIA PORT)
DC OUT:
5V, 0.7A MAX
Power consumption 250 W
Power consumption (during standby mode)
0.5 W (When “Control for
HDMI”, “Network
Standby” and “S-AIR
Standby” are set to “OFF”)
Dimensions (width/height/depth) (Approx.)
17 in × 6 1/4 in × 12 7/8 in
(430 mm × 157.5 mm ×
324.5 mm) including
projecting parts and
controls
Mass (Approx.)
19 lb 14 oz (9.0 kg)
Design and specifications are subject to
change without notice.
Halogenated flame retardants are not used in
the certain printed wiring boards.
147GB
STR-DN2010
4-182-049-11(1)
Additional Information
Windows
Media
Video
(WMV)
MPEG_PS_NTSC
defined in DLNA
guidelines 1.0
Maximum Resolution:
720 × 480
Maximum System Bitrate:
10.08 Mbps
Maximum Bitrate*
CBR: 9.80 Mbps/VBR:
9.80 Mbps
* Bitrate is mixed with
MPEG-1 Layer 1/2/3,
PCM, or AC3 audio
format.
General
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELIX.fm
masterpage: Left
Index
Numerics
C
E
2 channel 73
5.1 channel 19
7.1 channel 19
Cable TV tuner 31
Calibration Start 108, 123
Calibration Type 108, 123
Camcoder 32
Category Mode 67, 129
CD player 34
Clear
memory 39
remote 135
sound field 77
Connection
antennas 35
audio components 34
Network 37
speakers 21
TV 23
video components 25
Control for HDMI 117
Controller 81
Controllers 119
Crossover frequency 111,
125
Effect level 113
EQ Settings 114, 125
External Control 119
D
L
DCAC (Digital Cinema Auto
Calibration) 42
Decode Priority 115, 126
Device Name 120
DIGITAL MEDIA PORT 56
Direct Tuning 62, 68, 128,
129
Display 10
Distance Unit 113, 125
DLNA 78
DMPORT Control 58
Dolby Digital EX 76
Dual Mono 114, 126
DVD player 26, 30
DVD recorder 30, 32
Dynamic range compression
113, 124
Level Settings 123
LFE (Low Frequency Effect)
11
Listening 86
Lock Code 70
A
A.F.D. mode 73
A/V Sync 114, 126
Account 83
AM 61, 128
Antenna Aiming 67, 125,
129
Audio Out 117, 126
Audio Return Channel 103
Audio Settings 114, 126
Auto Calibration Settings
108, 123
Auto Standby 121, 127
Auto Tuning 62, 128
B
Bass 114, 125
BI-AMP 41, 106
Bi-amplifier connection 106
Blu-ray Disc player 26, 29
BRAVIA Sync
preparing 90
F
Favorite stations 87
FM 61, 128
FM Mode 62, 125
G
GUI (Graphical User
Interface) 52
H
HDMI Settings 117, 126
I
Input 54
Input Assign 104
INPUT MODE 103
iPod 58
148GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELIX.fm
masterpage: Right
M
R
T
Manual Setup 110
Menu 107, 123
Message
Auto Calibration 48
DIGITAL MEDIA
PORT 58
Error 144
SIRIUS 72
Movie mode 73
Music Guide 84
Music mode 74
Muting 55
My Library 85
My Library (Rhapsody) 86
RDS 64
Recording 60
Remote 13, 130
Repeat 80
Resetting 39
Resolution 116, 126
Rhapsody
Account 83
Music Guide 84
My Library 85, 86
Rhapsody Digital Music
Service 83
Rhapsody Stations 84
Search 85
Test Tone 111, 123
Theater/Theatre Mode Sync
93
Treble 114, 125
Tuner 61
Tuner Settings 125
TV 23, 26
N
S
Name Input 55, 64, 109
Network settings
Check 118
Network Standby 120
NIGHT MODE 77
S-AIR 94
S-AIR Settings 126
Satellite tuner 26, 31
Server
Preparing 50
Settings menu 107
Setup Manager 88
SHOUTcast
Favorite stations 87
Listening 86
Shuffle 80
SIRIUS ID 66
SIRIUS Satellite Radio 65,
129
Sleep Timer 59
Software Version 121
Sound field 73
Speaker Pattern 109, 124
Speaker Settings 109, 124
SPEAKERS 42
Subwoofer Level 118, 126
Subwoofer LPF 118
Super Audio CD player 34
Sur Back Assign 109
Surround Settings 113, 125
System Audio Control 92
System Power-Off 93
System Settings 121, 127
O
One-Touch Play 91
Option menu 53
P
Up converting 33
V
VCR 32
Video Settings 116, 126
Viewing information in the
display 127
Additional Information
Pairing 96
Parental Lock 70, 125
Party Mode 99
Pass Through 117, 126
Phase Audio 112, 123
Phase Noise 112, 123
“PlayStation 3” 26
Position (Auto Calibration)
108, 123
Preset channels 69, 130
Preset Mode 68
Preset stations 63, 128
PROTECTOR 144
U
149GB
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELIX.fm
masterpage: Left
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELIX.fm
masterpage: Left
STR-DN2010
4-182-049-11(1)
D:\NORM'S JOB\SONY HA\SO0071\STR-DN2010\GB\GB01COV_STR-DN2010-CELIX.fm
masterpage: Left
Sony Corporation Printed in Malaysia
model name1[STR-DN2010]
[4-182-049-11(1)]