Instruction manual | Dodge 2008 Ram 3500 Automobile User Manual

ROLLER
COMPACT
ROLLER COMPACT
3400
ROLLER COMPACT
340/400
ROLLER COMPACT 4000
For all customer enquiries or for replacement parts, contact:-
☎
0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
Carton Contents
ROLLER
COMPACT
340//3400/400
grassbox lid
lower handle
fixing pins
washer
bolts
height adjsutment lever
lock-off
button
washer
nuts
cable winder
attachment
(RC3400
only)
handle
knobs
deck
cable
clips
instruction
manual
spanner
/scraper
spacer
upper handle
electric cable with
moulded on plug
lower handle
ROLLER COMPACT 4000
Easi Reel
cable winder
(RC3400 only)
Easi-Reel
cable spool
washers
bolts
lower handle
fixing pins
grassbox lid
height adjsutment lever
lock-off
button
spanner/scraper
nuts
handle
knob
deck
cable
clips
spacer
instruction
manual
upper handle
electric cable with
moulded on plug
lower handle
IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:Husqvarna Outdoor Products Customer Service Department direct
Telephone : 0870 609 1901
Safety
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to
the operator and others, the warnings and safety instructions must be followed to ensure reasonable
safety and efficiency in using this lawnmower. The operator is responsible for following the warning
and safety instructions in this manual and on the lawnmower. Never use the mower unless the grassbox or guards provided by the manufacturer are in the correct position.
Explanation of Symbols on the Roller Compact
Beware of severing toes or hands.
Do not put hands or feet near a rotating
blade.
Warning
Read the user instructions carefully to make
sure you understand all the controls and
what they do.
Always keep the lawnmower on the ground
when mowing. Tilting or lifting the lawnmower
may cause stones to be thrown out
Keep bystanders away. Do not mow whilst
people especially children or pets are in the
mowing area
Switch off! Remove plug from mains before
adjusting, cleaning or if cable is entangled or
damaged. Keep the cable away from the blade.
STOP
Blade continues to rotate after the machine
is switched off.
Wait until all machine components have
completely stopped before touching them.
Do not mow in the rain or leave the lawnmower outdoors while raining
(RC3400/4000 only)
Unwind and remove fully before use.
General
1. Never allow children or people unfamiliar with these
instructions to use the mower. Local regulations may
restrict the age of the operator.
2. Only use the lawnmower in the manner and for the
functions described in these instructions.
3. Never operate the lawnmower when you are tired, ill
or under the influence of alcohol, drugs or medicine.
4. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
1. The British Standards Institute recommend the use of a
Residual Current Device (R.C.D.) with a tripping current of not
more than 30mA. Even with a R.C.D. installed 100% safety
cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it.
2. Before use, examine cable for damage, replace it if
there are signs of damage or ageing.
3. Do not use the lawnmower if the electric cables are
damaged or worn
4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do
not touch the electric cable until the electrical supply
has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one.
5. Your extension cable must be uncoiled or unwound,
coiled or wound cables can overheat and reduce the
efficiency of your mower.
6. Keep cable away from lawnmower, always work away from
the power point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable, replace it
with a new one. Use only Flymo replacement cable.
10.Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12.Never pull on the cable to disconnect any of the plugs.
13.Use only on AC mains supply voltage shown on the
product rating label.
14.Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to any part of the product.
Preparation
1. While using your product always wear substantial
footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
3. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good artificial light.
2. Avoid operating your lawnmower in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction
on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do
not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the mower towards you.
10.Switch off before pushing the mower over surfaces
other than grass.
11. Never operate the lawnmower with damaged guards
or without guards in place.
12.Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.
13.Do not tilt lawnmower when the motor is running,
except when starting and stopping. In this case, do
not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always
ensure that both hands are in the operating position
before returning the appliance to the ground.
14.Never pick up or carry a mower when it is operating
or still connected to the mains supply.
15.Remove the plug from the mains :
- before leaving the mower unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in a
safe operating condition.;
- if the lawnmower starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
2. Check the grassbox/grassbag frequently for wear or
deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt, spacer
and impeller specified for this product.
5. Be careful during adjustment of the lawnmower to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
CABLES
IMPORTANT
• Use only 1.00mm2 size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
• THE ROLLER COMPACT IS SUPPLIED WITH AN
ELECTRIC MAINS CABLE FITTED WITH A
FEMALE CONNECTOR
1. Flymo Mains Cables and Extension Cables are available from your local Approved Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna Outdoor
Products Approved Service Centre for further information on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS
IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT
IMPORTANT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth
be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accordance with the following code:
BLUE
NEUTRAL
BROWN
LIVE
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter
'L' or coloured RED.
4. It is important that the outer sheath is clamped correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard
against electrocution.
Assembly Instructions
B
A
C
D
grassbox lid
handle
knob
bolt
2
lower
handle
fixing
pins
1
Assembly of Lower Handles to Deck
1. Insert lower handle into holes in the deck (A).
2. Release the grassbox catch and lift the grassbox lid (B).
3. Rest the grassbox lid against the lower handle and
remove the grassbox.
4. Push the lower handle into place ensuring that the
holes in the lower handle are correctly located
behind the holes in the deck.
5. Secure the lower handles to the inside of the deck
with the lower handle fixing pins (C).
6. Ensure the fixing pins are securely located.
7. Should a problem occur when securing lower handle to deck,
E
washer
carefully lever fixing pins out of location and repeat steps 4 to 6.
8. Replace the grassbox and close the grassbox lid.
Assembly of Upper Handles to Lower Handles.
• Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost
1. Insert the nut into the handle knob (D1).
2. Ensure the upper handle and the lower handle are
aligned correctly. (D2)
3. Fit the bolts, washers and handle knobs.(D)
4. Fit the cable to the handles with the clips provided.
Make sure the cable is not trapped between the
upper and lower handles.
F
1
2
1
Cable Winder Assembly (E & F) RC3400 only
1. Insert cable winder attachment onto left upper
handle as viewed from rear of product (E1).
2. Insert cable winder onto attachment and turn
downward to secure. (E2).
3. Continue turning the cable winder downward until
it can be located onto the top of the lower handle
(F1).
Cutting Height Adjustment
G
Adjusting the cutting height
1. Lift the lever out of location and rotate to the desired
position. (G)
Heights of cut:1 & 2 - low, 3 - medium, 4 & 5 - high
H
spacer
The height of cut can be reduced further by the
addition of the spacer provided (H)
Always handle blade with care - sharp edges could
cause injury. USE GLOVES.
1. Remove the blade bolt and blade as described in
Removing the Blade and Fan
2. Place the spacer between the fan and the blade (H)
3. Replace the blade as described in Fitting the Blade
and Fan
Removing, Emptying and Refitting the Grassbox
J
Grassbox Full
• As the grassbox fills up, grass will be visible through
the window in the lid (J).
• When the window is full it is time to empty the grassbox.
grassbox
empty
Emptying the Grassbox
• Stop the lawnmower, as described in ‘To Stop your
Lawnmower’and wait until the blade has stopped rotating,
BEFORE lifting the grassbox lid.
1. Release grassbox catch and lift grassbox lid (B). See
Assembly Instructions.
2. Rest grassbox lid against lower handle and remove
grassbox (K).
3. Empty grassbox.
4. Replace grassbox and close grassbox lid.
grassbox
full
K
Cut Out Device
L
Cut out
•
•
•
IMPORTANT
The Roller Compact is fitted with a cut-out device
(L) which will prevent the lawnmower from being
started until the grassbox lid is firmly close and
clicked into place.
Do not attempt to use your lawnmower without the
grassbox in place or with the lid open.
IMPORTANT INFORMATION
When received from the
Manufacturer, the front wheels
are in a raised position.
Do not switch on this product before
removing from the raised position
into a desired height of cut. (M)
M
Starting and Stopping
N
P
Q
R
S
1
•
Important:- Your lawnmower will not start until the grassbox
lid is firmly closed and clicked into place.
To Start your Lawnmower
1. Connect female extension cable connector to the
back of the switchbox. (N)
2. Form loop in mains cable and push the loop through
the slot as illustrated in picture (P)
3. To secure, position loop over the hook and pull the cable
back through the slot as illustrated in picture (Q).
4. Connect plug to mains and switch on.
5. Tilt the handle downwards to slightly raise the front of
the lawnmower and to reduce the risk of lawn damage whilst starting.
The switchbox is provided with a lock-off button (R1) to
prevent accidental starting.
6. Press and hold the lock-off button (R) on the switchbox, then squeeze one of the Start/Stop levers
towards the upper handle (S).
7. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button.
8. Lower the lawnmower to its proper operating position
and commence mowing.
• NOTE: There are two start/stop levers fitted. Either one can
be used for starting the lawnmower.
• IMPORTANT: Do not use the start/stop levers intermittently
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
How to Mow
1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have
already cut.
2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one
time and this may also result in poor collection.
Do Not Overload Your Mower: Mowing long thick grass may cause the motor speed to drop, you will hear a change
in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When
mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Cutting Height
Adjustment.
Removing and Fitting the Blade and Fan (T)
T
fan
Always handle the blade with care - sharp edges could
cause injury. USE GLOVES.
Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and, with
the spanner provided, loosen the blade bolt by turning
it anti-clockwise.
2. Remove the blade bolt, blade and fan from the pulley.
3. Inspect for damage and clean as necessary.
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition.
If the blade is cracked or damaged replace it with a new
one.
Fitting the Blade and Fan
1. Ensure the fan is located correctly.
2. Fit the blade to the fan.
3 Re-assemble blade bolt through blade and fan.
4. Hold the fan and tighten blade bolt firmly with the
spanner provided. Do not over tighten.
blade bolt
blade
pulley
Easi-Reel Cable Winder (Roller Compact 3400/4000 only)
Storing your cable in the Easi-Reel cable winder
1. Insert the female connector into the centre of the cable winder (V1)
2. Place the cable under the cable guide (V2)
3. Turn the cable winder (V3) until all of the cable is wound in.(V4)
Warning:- When cable is fully wound, lid becomes heavy - Roller Compact 4000 only.
Unwinding the cable before re-use
1. Pull the cable by the plug and unwind the cable fully.
• Ensure that the cable is released from the cable guide (V2) before using your machine.
• Ensure cable is not entangled with any other cables and that it is not trapped in any parts of the product.
Roller Compact 3400
Roller Compact 4000
V1
V2
V1
V2
V3
V4
V3
V4
Caring for your Lawmower
W
Cleaning (W)
• USE GLOVES
• IMPORTANT: It is very important that you keep your
lawnmower clean. Grass clippings left in any of the air
intakes or under the deck could become a potential
fire hazard.
• IMPORTANT Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol,
or solvents - some can destroy critical plastic parts.
1. Remove grass from under the deck with the
spanne/scraper tool
2. Remove the blade, see Figure T, to gain access to the
fan and clean with a soft brush.
3. Raise the roller to its highest position, see Cutting
Height Adjustment, and clean with a soft brush.
4. Remove grass clippings from: all air intakes, wheels,
height adjustment lever and grassbox with a soft
brush.
5. Clean the grassbox lid and the inside of the window
with a soft brush.
6. Thoroughly clean around the cut-out switch with a soft
brush
7. Wipe over the surface of your lawnmower with a dry
cloth.
Cleaning Easi-Reel cable winder (Roller Compact
3400/4000 only)
• Roller Compact 3400 - At the back of the cable
winder, squeeze together the two catches (X) and
remove the cable spool.
• Roller Compact 4000 - Lift grassbox lid, squeeze together
the two catches (Y) and remove the cable spool.
2. Clean the cable spool and the area it was located with
a soft brush (Z)
3. Replace the cable spool, ensuring it clicks into place.
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required.
4. Make sure that the electric cable is wound properly.
Storing the lawnmower
The handles can be folded to take up the minimum of space.
• Loosen the handle knobs
• Fold the upper handle over the lawnmower.
• Ensure the switchbox cable is not trapped.
• Store in a dry place where your lawnmower is protected from damage.
X
Roller Compact 3400
X
Roller Compact 4000
Z
Roller Compact 3400
Roller Compact 4000
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed?
See ‘To Start your Lawnmower’.
2. Is the grassbox lid firmly closed?
3. Is the Power Turned On?
4. Check the fuse in the plug, if blown replace.
5. Fuse continues to blow?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Poor Grass Collection
1. Disconnect from the mains electricity supply.
2. Check that the grass chute and the underside of the
deck are free from grass.
3. Raise to a higher height of cut. See Cutting Height
Adjustment.
4. Clean Fan Blades.
5. If poor collection persists.
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Lawnmower becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut
should be raised to a higher position. See Cutting
Height Adjustment
3. Check that the wheels and roller can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a
new one.
4. If vibration persists, turn the blade through 180o by
first loosening the blade bolt, turning the blade and
re-tightening the blade bolt.
5. If vibration persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced at least
every twelve months, more often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Husqvarna
Outdoor Products stockists.
4. Your product is uniquely identified by a silver and black
product rating label
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of your
product as described on the product rating label.
6. Should it be necessary for work to be carried out by your Service
Centre, it is important to take your complete machine including cable
and any extension cables used.
A network of specialist dealers can be found in your local Yellow Pages.
To obtain service on your Flymo product simply telephone or visit your
local Service Centre. Should you require service under the terms of
our guarantee the Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare Parts.
NOTE: Our Service Repairers act on their own behalf and are not
empowered to commit or legally bind Husqvarna Outdoor Products in
any manner whatsoever.
Environmental Information
Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where
practical, components manufactured in the most environmentally responsible manner, according to company procedures,
and with the potential for recycling at the end of the products’ life.
•
Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
•
Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
•
If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local council office, your household waste
disposal service or the shop where you purchased the product.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture within the
guarantee period, Husqvarna Outdoor Products, through its Authorised
Service Repairers will effect the repair or replacement to the customer free
of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart
or tampered with by any person not authorised by
Husqvarna Outdoor Products.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important that
you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and their life
is dependent on regular maintenance and are, therefore not normally
subject to a valid warranty claim: Blade, Electric Mains cable, Belt
* Caution!
Husqvarna Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of
replacement parts or additional parts that are not either manufactured or
approved by Husqvarna Outdoor Products, or by the machine having
been modified in any way.
EC Declaration of Conformity
I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Ay c l i ffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP. Certify that the product:Category........ Electric Wheeled Rotary
Make..............Husqvarna Outdoor Products
Conforms to the specifications of Directive
2000/14/EEC
I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP Certify
that a sample of the above product has been
tested using directive 81/1051/EEC as a guide.
The maximum A-weighted sound pressure level
recorded at operator position under free field semi
anechoic chamber conditions was :-
Type of Cutting Device....Rotary Blade
Identification of Series......See Product Rating Label
Conformity Assessment Procedure....ANNEX VI
Notified Body................Intertek., Cleeve Road, Leatherhead,
Surrey. KT22 7SB England
Other Directives:-........98/37/EEC, 89/336/EEC, 73/23/EEC
& applicable standards:-. EN61000-3-2, EN61000-3-3,
EN55014-1, EN55014-2, EN836, EN60335-1, EN60335-2-77
I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
a guide. The maximum weighted root mean
square value of vibration recorded at operator’s hand position was:-
Type..................................................... RCV340
RCV3400 RCV400/4000
Width of Cut........................................ 34 cm
34 cm
40 cm
Speed of Rotation of Cutting Device... 3,800 RPM 4,300 RPM 4,350 RPM
Guaranteed sound power level........... 96 dB (A)
96 dB (A)
90 dB (A)
Measured Sound Power Level............ 95 dB (A)
95 dB (A)
89 dB (A)
Level.................................................... 87.5 dB (A) 87.5 dB (A) 79.1 dB (A)
Value....................................................3.25 m/s2
3.25 m/s2
2.97 m/s2
Weight..................................................13.5 kg
13.5 kg
11 kg
Newton Aycliffe, 08/02/06
M. Bowden,
Research & Development Director
Husqvarna Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 870 609 1901 Fax - (00) 44 870 609 1902
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
5107353-02
Download PDF

advertising