Operating instructions | Dometic DS 300 H Refrigerator User Manual

Health Care refrigerator
DS 300 H
DS 600 H
Operating Instructions
207.5387.01
GB
IE
Please read these operating instructions carefully before putting the
refrigeration unit into operation. If you later sell or dispose of it, please ensure
that the new owner receives these operating instructions.
Please follow the installation details below carefully Guarantee is valid for
products installed as described only.
Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.
In the following, we would like to familiarise you with some symbols, which we bring to your attention to ensure
the safe and efficient operation of the appliance:
source of danger, in event of improper operation
suggested useful tips to read
information concerning environmental protection
This refrigerator is intended for the storage of drugs at temperatures within the range +2°C to +8°C. A digital
type thermometer is provided which may be fixed to the top of refrigerator. (Fig.2, page 4)
Attention!
THIS REFRIGERATOR IS NOT SUITABLE FOR THE STORAGE OF BLOOD.
Attention!
This product is designed to be operated by adults. Children should not be
allowed to tamper with the controls or play with the product.
Any electrical work required to install this appliance should be carried out by a
qualified electrician.
This product should be serviced by an authorised Service Engineer, and only
genuine spare parts should be used.
It is dangerous to alter the specifications or modify this product in any way.
Care must be taken to ensure that the appliance does not stand on the
electrical supply cable.
There are working parts in this product which heat up. Always ensure that there
is adequate ventilation as a failure to do this will result in component failure
and possible content loss. See installation instructions.
Parts which heat up should not be exposed. The back of the product should be
close to a wall but leaving the required distance for ventilation as stated in the
installation instructions.
Before defrosting, cleaning or maintenance work is carried out, be sure to
switch off the appliance and unplug it.
DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Under no
circumstances should solid ice be forced off the cooling fins. Solid ice should
be allowed to thaw when defrosting the appliance. See defrost instructions.
This appliance is heavy. Care should be taken when moving it.
Under no circumstances should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may cause injury or more serious
malfunctioning. Refer to your local Service Centre and always insist on
genuine spare parts.
In this appliance the storage of any toxic or explosive substance is forbidden!
2
CONTENT S
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Unpacking
View of the appliance
Cleaning
Positioning the appliance
4.1.
Installation instruction
Using the appliance
5.1.
Initial operation
5.2. Temperature regulation
Thermometer
Useful suggestions
Defrosting, cleaning and maintenance
Interior light
Reversing the door hang
Replacing the decorative door panel
Customer service
Putting into operation, technical data
13.1. Connecting to electrical mains
Environmental protection information
Recycling
Attention!
Warranty arrangements are in accordance with EC Directive 44/1999/CE and the
normal conditions applicable in the country concerned.
For warranty or other servicing, such as spare-parts, please contact our Dometic
Service Network.
The warranty does not cover any damage due to improper use.
The warranty does not cover any modifications to the appliance or the use of nonoriginal Dometic spare-parts.
The warranty does not apply if the installing and operating instructions are not adhered
to.
When contacting Dometic Service Network, please state the model, product number
and serial number. You will find this information on the data plate inside of the
refrigerator.
3
1. Unpacking
After removal from the cardboard packaging, make
sure the appliance is not damaged. If you find damage
to the appliance resulting from transport, report it
immediately to the transportation firm.
Figure 1
2. View of the appliance
DS 300 H
DS 600 H
Figure 2.
1. Door lock
2. Door
3. Evaporator
4. Thermometer
5. Thermostat knob
6. Cooling unit room cover
7. Interior light
8. Trays
9. Footframe
10. Sensor of Fuzzy Logic
IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC RT DO NOT ACCEPT
LIABILITY FOR LOSS OR DAMAGE OF KEYS. HOWEVER A COMPLETE LOCK CAN BE SUPPLIED.
4
3. Cleaning
Clean the refrigerator thoroughly at intervals, as
necessary. Remove the shelves; these, the
cabinet interior and the door should be washed with a
warm solution of sodium bi-carbonate. Finally wipe
over with a cloth rinsed in warm water only, and dry
with a clean cloth. Do not wash any plastic parts in
water that is more than hand warm, and do not expose
them to dry heat. The outside of the cabinet should be
wiped down regularly with a clean, damp cloth.
NEVER USE STRONG CHEMICALS OR ABRASIVE
CLEANING MATERIALS ON ANY PART OF THE
CABINET.
The miniCool achieves its operating temperature
after several hours.
5.2. Temperature regulation
The usual setting required is in the region of the
middle of the thermostat knob (Fig. 6), but this can
vary with conditions of load and installation. If it is
found necessary to alter the setting,the knob can
be turned to a higher symbol to produce a colder
temperature, or a lower symbol to produce a
warmer temperature. The effect of any adjustment
can be checked by means of a thermometer after
leaving the refrigerator operating for a further
period to settle down again.
4. Positioning the appliance
When first using this refrigerator please consider the
following points:
ENSURE REFRIGERATOR IS LEVEL
THE PIPEWORK AT THE BACK GETS HOT IN USE
THE REFRIGERATOR HAS NO 'MOTOR' AND IS
THEREFORE VIRTUALLY SILENT
ALLOW AT LEAST 3 HRS. FOR SIGNS OF
COOLING
During the refrigeration process, the appliance
gives off heat from the condenser (under the
upper part of the rear cover) into the surrounding air.
The more ventilated the condenser is, the more
effective the refrigeration will be.
The other condition for satisfactory operation is that
the appliance stands on a flat surface. This is best
seen by placing a glass of water on top of the
appliance.
It is important that the appliance is not directly
exposed to radiated heat (sunlight, radiator, near an
oven, etc.).
Please do not place the refrigerator onto thick
carpet!
4.1. Installation instructions
This version is supposed to be freestanding. Cooling
unit room cover protects from the hot parts of the
cooling unit. Foot frame with grilles ensures sufficient
ventilation.
5. Using the appliance
To start the refrigerator connect the plug to the socket
outlet and switch on the socket. The cooling fins
should show signs of cooling after about 1-2 hours
depending on ambiant temperature.
5.1. Initial operation
The device must be plugged into a properly earthed
socket.
The miniCool starts automatically with a self-test.
The LED illuminates after plugging-in several times
and after that continuous light can be seen if the
door is open.
Figure 3.
6. Thermometer (Fig. 4)
Refer to the separate instruction leaflet supplied
with the thermometer. The thermometer can be
stood up using the attached stand or alternatively it
can be fixed to the refrigerator door, in which case
the sensor wire should be arranged so that it is not
stretched or damaged when the door is opened.
The temperature sensor is located inside the
refrigerator in the upper left corner in front of the
evaporator.
The display will then show the current, maximum
and minimum temperature inside the refrigerator.
After the first pull down of the refrigerator (allow
four hours) please make a "reset" on the
thermometer because otherwise it will keep as
"maximum" the ambient temperature.
If you find lower than +2 °C or even negative
temperature as a minimum on the screen, it must
have occured due to a cutout in the electrical
circuit. In these circumstance's the electronic
thermostat will make a restart and start to cool
down the refrigerator, without monitoring the
refrigerator for 45 minutes. If you reset the
thermometer again (1-2 hours later) and the normal
+2 ... +8 °C is shown then you can be sure that the
medincines have not been damaged or frozen.
The more medicines you store in the refrigerator
then reduces the hazard of freezing, if the unit has
a short period of time undercooling.
We take no responsibility for damage to
vaccines through freezing, if there has been a
cutout in the electricity for a short period of
time.
It is important to reset the thermometer regularly to
ensure that the temperature is maintained between
2 °C and 8 °C.
5
The temperature readings may rise temporarily after
opening the door or placing additional items inside the
cabinet.
On the thermometer the battery transit strip must be
removed to activate the temperature display.
C
9. Interior light
Two light-emitting diodes (A) on an electronic PCB
illuminate the cooling compartment when the door
is opened.
Two sensors (B) control whether the door is open
or not and the LEDs will work accordingly.
B
A
Figure 6.
10. Reversing the door hang,
Figure 4.
7. Useful suggestion
Do not overfill the appliance. It is advisable to leave
some space between the products in the cabinet to
ensure efficient and even cooling. If the shelves are
packed too tightly there may be unacceptable
temperature variations.
8. Defrosting, cleaning and
maintenance
Frost will gradually form on the cooling surfaces and it
must not be allowed to become too thick since it acts
as an insulator and interferes with the cooling.
We recommend to defrost the appliance in every 3
weeks, or depending on the ice quantity on the
cooling fins. While defrosting the appliance should be
switched off by disconnecting the refrigerator from the
electricity supply and leave the cabinet door open.
The frost will melt and the defrost water will run
through the drain tube from the drip channel into an
evaporating vessel located at the bottom rear of the
refrigerator. (Fig 5.)
After defrosting the cabinet interior should be wiped
out with a clean, damp cloth.
Figure 5.
6
(Fig. 7-8.)
Disconnect at the mains.
Lay the appliance on its side.
Loosen up 7 screws (1) of footframe and remove
the footframe.
Put the fridge on a desk to ease the work.
Open the door and snap out the fixing tab (2) of
the upper hinge pin by the help of screwdriver
and push out the pin. (fig. 8.)
Remove the door and the hinge washer.
Remove the bottom hinge pin (3) and the upper
and lower hinge plug (4) in the same way as in
case of the upper hinge pin.
Snap in the lower hinge pin (3) to the desired
side.
Put back the door and the hinge washer and
snap in the upper hinge pin (2).
Snap in the 2 hinge plugs (4) too.
Put back the footframe with its screws.
Figure 7.
(Details of the model, product- and serialnumber
are to be found on the data label in the top left of
the inside compartment.)
This refrigerator is equipped with overheating
protection. An authorised service technician can
check whether this has been triggered or not.
In the event of a fault developing, contact your
nearest Service Centre-see local telephone
directory.
13. Putting into operation
Technical data:
Figure 8.
11. Replacing the decorative
door panel, Fig. 9
1
3
1
2
4
Figure 9.
Remove the mounter screws (1) of the forehead
panel.(3)
Remove rosette (2) (in case of with lock version fridge).
Lift and remove the forehead panel.(3)
Slide the decorative panel (4) out of the door frame
and insert the new panel (thickness max. 2 mm).
Place back the forehead panel,rosette and screw in
reverse sequence.
12. Customer service
Before you call a service engineer, carry out the
following simple tests:
Is there a power failure? Check the fuses.
Is the plug firmly connected to the socket and is the
socket switched on? Check the socket by plugging
in another appliance, e.g. a table lamp.
Is the thermostat at the correct setting?
Has the door not been closed properly causing the
inside temperature to rise too quickly?
Is the refrigerator level?
Has the ventilation become obstructed?
If after checking all the above points, the refrigerator
is still not working satisfactorily, contact your nearest
service engineer. State the problem, model, productand serial-number.
Model
Type
Gross volume
Mains operation
Input
Energy consumption
Climate class
Refrigerant
DS 300 H
DS 20-60
28,1 litre
220 - 240V (AC)
65W
0,76 kWh/24h
SN
151g H2O + 101g NH3
DS 600 H
DS 20-60
52,6 litre
220 - 240V (AC)
85W
0,88 kWh/24h
SN
157g H2O + 105g NH3
13.1. Connecting to electrical mains
The appliance may only be operated from
nominal voltage mains as shown on the data
plate. The appliance mains plug may be connected
to a mains socket earthed in accordance with
regulations.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity
supply voltage is the same as that indicated on the
appliance rating plate.
Only for UK:
The appliance is supplied with a 3 amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 3 amp ASTA approved (BS 1362) fuse
must be used. Should the plug need to be replaced
for any reason, the wires in the mains lead are
coloured in accordance with the following code:
Green and Yellow:
Blue:
Brown:
Earth
Neutral
Live
7
The appliance does not contain any CFCs/HCFCs.
Ammonia (natural hydrogen and nitrogen compound)
is used as a refrigerating agent in the refrigeration unit.
The ozone-friendly cyclopentane is activated as a
motive agent for the PU foam insulation.
Sodium chromate is used for corrosion protection
(less than 2 weight % of the coolant).
After unpacking the appliance, the packing
materials should be delivered to a local collection
site. At the end of its useful lifetime, the appliance
should be delivered to a specialised collection and
reprocessing firm, which reclaims the usable
materials. The rest is properly destroyed.
This appliance compiles whit the following EEC
directives:
LVD-Directive 73/23/EEC with amendment
90/683/EEC
EMC-Directive 89/336/EEC
2004. 06. 23.
14. Environmental protection
information
15. Recycling
Printed by Xerox Hungary Ltd.
The wire coloured green and yellow must be
connected to the terminal marked with the letter „E“ or
by the earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal „N“ or coloured black.
The wire coloured brown must be connected to the
terminal marked „L“ or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
Download PDF

advertising