Installation guide | Draytek 2820 Series Network Router User Manual

Vigor2820 Series
ADSL2/2+ Security Firewall
Quick Start Guide
Version: 1.0
Date: 2007/07/24
i
Copyright Information
Copyright
Declarations
Copyright 2007 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
z
Microsoft is a registered trademark of Microsoft Corp.
z
Windows, Windows 95, 98, Me, NT, 2000, XP and Explorer are
trademarks of Microsoft Corp.
z
Apple and Mac OS are registered trademarks of Apple Inc.
z
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
z
z
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
z
Do not place the router in a damp or humid place, e.g. a bathroom.
z
Do not stack the routers.
z
The router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
z
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
z
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
z
Keep the package out of reach of children.
z
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com
i
European Community Declarations
Manufacturer:
Address:
Product:
DrayTek Corp.
No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Vigor2820 Series Router
DrayTek Corp. declares that Vigor2820 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 73/23/EEC by complying with
the requirements set forth in EN60950.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct the interference
by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different form that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Please visit www.draytek.com/about_us/Regulatory.php.
ii
Table of Contents
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2820 ............................................................................................................... 2
1.1.2 For Vigor2820n ............................................................................................................. 4
1.1.3 For Vigor2820Vn ........................................................................................................... 6
1.1.4 For Vigor2820VS........................................................................................................... 8
1.1.5 For Vigor2820VSn....................................................................................................... 10
1.2 Package Content...................................................................................................................... 12
2. Installing Your Router......................................................................................... 13
2.1 Hardware Installation................................................................................................................ 13
2.2 ISDN Phone Adapter Installation.............................................................................................. 14
2.3 Printer Installation..................................................................................................................... 16
3. Configuring Web Pages ..................................................................................... 21
3.1 Basic Configuration .................................................................................................................. 21
3.2 Wireless Configuration ............................................................................................................. 25
3.2.1 Basic Wireless LAN Concept ...................................................................................... 25
3.2.2 General Setup ............................................................................................................. 25
3.2.3 Security Settings ......................................................................................................... 27
4. Trouble Shooting ................................................................................................ 29
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 29
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 30
4.3 Pinging the Router from Your Computer .................................................................................. 32
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 33
4.5 Backing to Factory Default Setting If Necessary...................................................................... 35
4.6 Contacting Your Dealer ............................................................................................................ 37
iii
1. Introduction
The Vigor2820 is an ADSL2+ router with 2nd Ethernet WAN. This 2nd WAN can connect
to DSL/Cable modem or fiber media converter for policy-based load-balance, fail-over
and BoD (Bandwidth on Demand); it also features advanced bandwidth control
mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to
allow easy, flexible, reliable access control and bandwidth management.
The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of
firewall policies easy. The CSM (Content Security Management) feature allows more
precise and efficient access control for URL/Web Content Filtering, IM (Instant
Messenger) and P2P (Peer to Peer) applications.
With hardware-based implementation of the VPN protocols, the Vigor2820 supports up to
32 VPN tunnels using advanced protocols such as IPSec/PPTP/L2TP/L2TP over IPSec
with AES/DES/3DES for encryption and MD5/SHA-1 for authentication.
Vigor2820 ‘n’ models comply with 802.11n Draft-n standards. They support
WEP/WPA/WPA2 encryption and MAC Address Control, Wireless LAN Isolation, and
802.1X authentication. The Wireless Rate Control function can adjust the data rate of
each wireless station (client).
Vigor2820 ‘V’ models provide twin analogue phone and one line port. ‘S’ models also
support twin ISDN ports that one is fixed as ISDN S0 port for ISDN phone and the other
is configurable for ISDN line and phone. It supports multiple SIP registrars with high
flexible configuration and call handing options.
Definitions for ISDN Ports
Below shows the names that displayed on front panel of the device and the WEB UI of
this device.
ISDN TE (Terminal Equipment) means an interface for transmitting analog signal
through Internet between Switching and router. Such interface is also named with ISDN
S0 extern in Germany.
ISDN NT (Network Terminator) is a port that used to connect general phone. Such
interface is also named with ISDN S0 intern in Germany.
The Phone S0 port on Vigor2820 series is fixed to connect phone forever and the LED on
the connecter will light orange always. However ISDN/Phone S0 port on this device is
configurable for connecting phone or accessing Internet according to the settings that you
adjust on WEB UI (please refer to VoIP>>Phone Setting for detailed information).
Warning: When the orange LED lights (means ISDN NT mode), the ISDN
port can be used to connect phone only. Wrong ISDN connection might cause
severe damage on your device.
1
1.1 Panel Explanation
1.1.1 For Vigor2820
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
Blinking
On
Blinking
On
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management) for
IM/P2P application is active. (It is enabled from
Objects Setting >> CSM Profile).
The Web Content Filter is active. (It is enabled from
Firewall >> Web Content Filter Setup)
The router is ready to access Internet through DSL link.
Slowly: The connection is ready.
Quickly: The connection is tranning.
The router is ready to access Internet through WAN
connection.
It will blink while transmitting data.
The DoS/DDoS function is active.
It will blink while deleting an attack.
The VPN tunnel is active.
The QoS function is active.
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
USB
CSM
CPA (Content Portal
Authority)
DSL
WAN2
On
On
Blinking
On
DoS
VPN
QoS
LED on Connector
LAN 1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN 2/3/4
Left LED
(Green)
Right LED
(Green)
WAN 2
Left LED
(Green)
Right LED
(Green)
2
Interface
Description
Factory Reset
LAN (1-4)
DSL
WAN 2
USB
PWR
Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
3
1.1.2 For Vigor2820n
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
Blinking
On
Blinking
On
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management) for
IM/P2P application is active. (It is enabled from
Objects Setting >> CSM Profile).
Wireless access point is ready.
It will blink while wireless traffic goes through.
The router is ready to access Internet through DSL link.
Slowly: The connection is ready.
Quickly: The connection is tranning.
The router is ready to access Internet through WAN
connection.
It will blink while transmitting data.
The DoS/DDoS function is active.
It will blink while deleting an attack.
The VPN tunnel is active.
The QoS function is active.
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
USB
CSM
WLAN
On
Blinking
On
Blinking
DSL
WAN2
On
DoS
VPN
QoS
LED on Connector
LAN 1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN 2/3/4
Left LED
(Green)
Right LED
(Green)
WAN 2
Left LED
(Green)
Right LED
(Green)
4
Interface
Description
WLAN
LAN (1-4)
DSL
WAN 2
USB
PWR
Push this button to enable (WLAN LED on) or disable (WLAN LED off) wireless
connection.
Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
5
1.1.3 For Vigor2820Vn
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
On
Off
Blinking
On
Off
On
Off
On
Off
Blinking
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management) for
IM/P2P application is active. (It is enabled from
Objects Setting >> CSM Profile).
Wireless access point is ready.
It will blink while wireless traffic goes through.
The router is ready to access Internet through DSL link.
Slowly: The connection is ready.
Quickly: The connection is tranning.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
Web Content Filter is disabled.
Web Content Filter is enabled to filter web pages.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
USB
CSM
WLAN
On
Blinking
On
Blinking
DSL
WAN 2
Left LED
(Green)
Right LED
(Green)
Line
Phone 1/2
LED on Connector
LAN 1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN 2/3/4
Left LED
(Green)
Right LED
(Green)
WAN 2
Left LED
(Green)
Right LED
(Green)
6
Interface
Description
WLAN
Phone 1/2
Line
LAN (1-4)
DSL
WAN 2
USB
PWR
Push this button to enable (WLAN LED on) or disable (WLAN LED off) wireless
connection.
Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
Connecter for PSTN phone.
Connector of analog phone for PSTN life line.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
7
1.1.4 For Vigor2820VS
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management)
for IM/P2P application is active. (It is enabled from
Objects Setting >> CSM Profile).
The Web Content Filter is active. (It is enabled from
Firewall >> Web Content Filter Setup)
The router is ready to access Internet through DSL link.
Slowly: The connection is ready.
Quickly: The connection is tranning.
The WAN1 or WAN2 connection is ready.
It will blink while transmitting data.
Web Content Filter is disabled.
Web Content Filter is enabled to filter web pages.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
USB
CSM
CPA (Content Portal
Authority)
DSL
WAN 2
On
On
Blinking
On
Blinking
On
Off
On
Off
Blinking
Line
Phone 1/2
LED on Connector
On
Phone S0
Left LED
(Orange)
Blinking
On
Right LED
(Green)
ISDN/Phone
S0
Blinking
On
Left LED
(Orange)
Blinking
Off
Right LED
(Green)
On
Blinking
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is connected.
ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is not connected.
A phone has been connected. If not, green LED will be
off.
An ISDN phone is off-hook or a phone call comes.
ISDN NT (ISDN S0 intern) mode is active configured
from VoIP>>Phone Settings and an ISDN phone
adapter is connected.
ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN phone
adapter is not connected.
It means ISDN TE mode is active which is configured
from VoIP>>Phone Settings.
A phone adapter with phone set has been connected
(ISDN S0 intern mode) or ISDN line has been
connected (ISDN S0 extern mode). It will be off if
there is nothing connected.
In ISDN NT (ISDN S0 intern) mode, it means an ISDN
phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice (phone
call) is transmitting.
8
LAN 1(Giga)
Left LED
(Green)
Right LED
(Green)
LAN 2/3/4
Left LED
(Green)
Right LED
(Green)
WAN 2
Left LED
(Green)
Right LED
(Green)
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
Interface
Description
Factory Reset
ISDN/Phone
S0
Phone (1/2)
Line
LAN (1-4)
DSL
WAN 2
USB
PWR
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more
than 5 seconds. When you see the ACT LED begins to blink rapidly than usual,
release the button. Then the router will restart with the factory default
configuration.
Connecter for ISDN phone(s) only via ISDN phone adapter. Do not connect any
other device to such port or connect ISDN line, otherwise the router might be
damaged.
Connecter for ISDN line or ISDN phone adapter in particular condition. Refer to
section 2.2 for more details.
Connecter for PSTN phone.
Connector of analog phone for PSTN life line.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Phone S0
9
1.1.5 For Vigor2820VSn
LED
Status
Explanation
ACT (Activity)
Blinking
Off
On
Blinking
On
The router is powered on and running normally.
The router is powered off.
A USB device is connected and active.
The data is transmitting.
The profile of CSM (Content Security Management) for
IM/P2P application is active. (It is enabled from
Objects Setting >> CSM Profile).
Wireless access point is ready.
It will blink while wireless traffic goes through.
The router is ready to access Internet through DSL link.
Slowly: The connection is ready.
Quickly: The connection is tranning.
The WAN1 or WAN2 connection is ready.
It will blink while transmitting data.
Web Content Filter is disabled.
Web Content Filter is enabled to filter web pages.
The phone connected to this port is off-hook.
The phone connected to this port is on-hook.
A phone call comes.
USB
CSM
WLAN
On
Blinking
On
Blinking
DSL
WAN 2
On
Blinking
On
Off
On
Off
Blinking
Line
Phone 1/2
LED on Connector
On
Phone S0
Left LED
(Orange)
Blinking
On
Right LED
(Green)
ISDN/Phone
S0
Blinking
On
Left LED
(Orange)
Blinking
Off
Right LED
(Green)
On
Blinking
LAN 1(Giga)
Left LED
(Green)
On
Off
ISDN NT (ISDN S0 intern) mode is active and an ISDN
phone adapter is connected.
ISDN NT (ISDN S0 intern) mode is active and an ISDN
phone adapter is not connected.
A phone has been connected. If not, green LED will be
off.
An ISDN phone is off-hook or a phone call comes.
ISDN NT (ISDN S0 intern) mode is active configured
from VoIP>>Phone Settings and an ISDN phone
adapter is connected.
ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN phone
adapter is not connected.
It means ISDN TE mode is active which is configured
from VoIP>>Phone Settings.
A phone adapter with phone set has been connected
(ISDN S0 intern mode) or ISDN line has been
connected (ISDN S0 extern mode). It will be off if there
is nothing connected.
In ISDN NT (ISDN S0 intern) mode, it means an ISDN
phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice (phone
call) is transmitting.
The port is connected.
The port is disconnected.
10
Right LED
(Green)
LAN 2/3/4
Left LED
(Green)
Right LED
(Green)
WAN 2
Left LED
(Green)
Right LED
(Green)
Interface
WLAN
Blinking
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The data is transmitting.
The port is connected with 1000Mbps.
The port is disconnected with 10/100Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is disconnected with 10Mbps.
Description
ISDN/Phone
S0
Phone (1/2)
Line
LAN (1-4)
DSL
WAN 2
USB
PWR
Push this button to enable (WLAN LED on) or disable (WLAN LED off) wireless
connection.
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more
than 5 seconds. When you see the ACT LED begins to blink rapidly than usual,
release the button. Then the router will restart with the factory default configuration.
Connecter for ISDN phone(s) only via ISDN phone adapter. Do not connect any
other device to such port or connect ISDN line, otherwise the router might be
damaged.
Connecter for ISDN line or ISDN phone adapter in particular condition. Refer to
section 2.2 for more details.
Connecter for PSTN phone.
Connector of analog phone for PSTN life line.
Connecters for local networked devices.
Connecter for accessing the Internet through ADSL2/2+.
Connecter for remote networked devices.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power adapter.
ON/OFF
Power Switch.
Factory Reset
Phone S0
11
1.2 Package Content
nQuick Start Guide
oCD
p RJ-45 Cable (Ethernet)
q RJ-45 to RJ-45 Cable for S models
r ISDN Phone Adapter (VS models)
s Analog Phone Adapter (V models)
s The type of the power adapter depends on the country that the router will be installed:
UK-type Power Adapter
EU-type Power Adapter
USA/Taiwan-type Power Adapter
AU/NZ-type Power Adapter
* The maximum power consumption is 17-23 Watt.
12
2. Installing Your Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect the ADSL interface to the external ADSL splitter with an ADSL line cable
for all models. For Vigor2820Vn/VS/VSn, also connect Line interface to external
ADSL splitter.
For second WAN, connect the cable Modem/DSL Modem/Media Converter to
WAN2 port of router with Ethernet cable (RJ-45).
2.
Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer.
3.
Connect the telephone sets with phone lines (for using VoIP function). For the model
without phone ports, skip this step.
4.
Connect one end of the power adapter to the router’s power port on the rear panel,
and the other side into a wall outlet.
5.
Power on the device by pressing down the power switch on the rear panel.
6.
The system starts to initiate. After completing the system test, the ACT LED will
light up and start blinking.
(For the detailed information of LED status, please refer to section 1.1.)
13
Caution: Each of the Phone ports can be connected to an analog phone only. Do not
connect the phone ports to the telephone wall jack. Such connection might damage your
router.
2.2 ISDN Phone Adapter Installation
Such information is provided for Vigor2820 S models (e.g., Vigor2820VS/VSn).
Phone S0 is always fixed to connect ISDN phone. However, ISDN /Phone S0 is
configurable as NT or TE mode. When the user configures ISDN /Phone S0 as NT mode
in VoIP>> Phone Settings, the orange LED will light on to indicate ISDN-NT is
selected. And by using ISDN phone adapters (coming from the router package), the user
can connect several phones to Vigor2820VS for communication. Refer to the following
figure for reference.
14
Yet, if the user configures ISDN / Phone S0 as TE Mode in VoIP>> Phone Settings, the
green LED will light on to indicate ISDN-TE is selected. Then, the port is specified for
ISDN line only. Refer to the following figure for reference.
15
2.3 Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this
router can print documents via the router. The example provided here is made based on
Windows XP/2000. For Windows 98/SE, please visit www.draytek.com.
Before using it, please follow the steps below to configure settings for connected
computers (or wireless clients).
1.
Connect the printer with the router through USB/parallel port.
2.
Open Start->Settings-> Printer and Faxes.
16
3.
Open File->Add a New Computer. A welcome dialog will appear. Please click
Next.
4.
Click Local printer attached to this computer and click Next.
5.
In this dialog, choose Create a new port Type of port and use the drop down list to
select Standard TCP/IP Port. Click Next.
17
6.
In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer
Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next.
7.
Click Standard and choose Generic Network Card.
8.
Then, in the following dialog, click Finish.
18
9.
Now, your system will ask you to choose right name of the printer that you installed
onto the router. Such step can make correct driver loaded onto your PC. When you
finish the selection, click Next.
10. For the final stage, you need to go back to Control Panel-> Printers and edit the
property of the new printer you have added.
11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK.
Next please refer to the red rectangle for choosing the correct protocol and UPR
name.
19
The printer can be used for printing now. Most of the printers with different
manufacturers are compatible with vigor router.
Note 1: Some printers with the fax/scanning or other additional functions are not
supported. If you do not know whether your printer is supported or not, please visit
www.draytek.com to find out the printer list. Open Support Center->FAQ->Sort
by product; select the model of the router and click on it; find out the link of Printer
Server FAQ; click the What types of printers are compatible with Vigor router?
link.
Note 2: Vigor router supports printing request from computers via LAN ports but not
WAN port.
20
3. Configuring Web Pages
To access Internet, please finish basic configuration after completing the hardware
installation.
3.1 Basic Configuration
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1.
Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Do not type any word on the window and
click OK for next screen.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
3.
Now, the Main Screen will pop up. Click Quick Start Wizard.
21
Note: The home page will change slightly in accordance with the router you have.
4.
Enter the login password on the field of New Password and retype it on the field of
Retype New Password. Then click Next to continue.
5.
On the next page as shown below, please select the WAN interface (WAN 1 or
WAN2) that you use. If DSL interface is used, please choose WAN1; if WAN2
interface is used, please choose WAN2. Choose Auto negotiation as the physical
type for your router. Then click Next for next step.
22
6.
On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select
PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step.
PPPoE/PPPoA: if you click PPPoE or PPPoA as the protocol, please manually enter
the Username/Password provided by your ISP. Then click Next.
23
1483 Bridged IP /1483 Routed IP: if you choose 1483 Bridged IP / 1483 Routed IP
as the protocol, you will get the following page. Please type in the IP address
information originally provided by your ISP. Then click Next for next step.
7.
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
24
3.2 Wireless Configuration
For the user of Vigor2820/2820VS, please skip this section.
For operating Vigor2820n/Vn/VSn well, it is necessary for you to set the wireless LAN
settings for using wireless function. Please read the following section carefully for
configuring the settings for this router.
(The default value of Frequency Domain was set by factory depends on the reselling
region.)
3.2.1 Basic Wireless LAN Concept
In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an
Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs
(clients) will share the same Internet connection with other wired hosts via Vigor wireless
router.
3.2.2 General Setup
1.
On the Wireless LAN group, select General Setup. The following page will be
shown as below.
25
2.
Check Enable Wireless LAN to enable the wireless function.
3.
At present, the router can connect to 11b+11g, 11g Only, 11b Only, 11n Only and
Mixed (11b+11g+11n) stations simultaneously. Simply choose Mix (11b+11g+11n)
mode.
Note: You should also set RADIUS Server simultaneously if 11g Only, 11b Only or
11n Only mode is selected.
4.
Type in the name of the SSID. The default name for SSID is default. We suggest
you change it to a particular name for your necessity.
SSID (service set
identifier)
5.
It is used to name the wireless LAN for this router, and it must
have the same content in client PC/notebook wireless card(s).
SSID can be any text numbers or various special characters.
The default channel is 6. You can change it to an appropriate one if the selected
channel is under serious interference.
26
3.2.3 Security Settings
1.
On the Wireless LAN group, select Security Settings.
2.
Select an appropriate encryption mode to improve the security and privacy of your
wireless data packets.
3.
Disable
Turn off the encryption mechanism. For the security of your
router, please select any one of the encryption mode here.
WEP
Accepts only WEP clients and the encryption key should be
entered in WEP Key.
WPA/PSK
Accepts only WPA clients and the encryption key should be
entered in PSK.
WPA2/PSK
Accepts only WPA2 clients and the encryption key should be
entered in PSK.
Mixed (WPA+
WPA2)/PSK
Accepts WPA and WPA2 clients simultaneously and the
encryption key should be entered in PSK.
For WPA encryption, type in 8~63 ASCII characters or 64 Hexadecimal digits
leading by 0x, for example "0123456789ABCD...." or "0x321253abcde....." on the
27
field of Pre-Shared Key (PSK). WPA encrypts each frame transmitted from the
radio using the Pre-Shared Key (PSK) which entered from this panel.
4.
As to WEP encryption, select 64-bit or 128-bit as the encryption mode. For 64bits
WEP key, type in 5 ASCII characters or 10 hexadecimal digitals leading by 0x, for
example, ABCDE or 0x4142434445. And for 128bits WEP key, type in 13 ASCII
characters or 26 hexadecimal digits leading by 0x, for example, ABCDEFGHIJKLM
or 0x4142434445464748494A4B4C4D. Only one WEP key can be selected and
allows user to type in the characters.
5.
Click OK to save settings.
Be aware that for the communication, all wireless devices must support the same
encryption bit length and share the same key. If WEP mode is selected, only one of four
preset keys can be selected at one time.
28
4. Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the
Internet after installing the router and finishing the web configuration. Please follow
sections below to check your basic installation status stage by stage.
¾
Checking if the hardware status is OK or not.
¾
Checking if the network connection settings on your computer are OK or not.
¾
Pinging the router from your computer.
¾
Checking if the ISP settings are OK or not.
¾
Backing to factory default setting if necessary.
If all above stages are done and the router still cannot run normally, it is the time for you
to contact your dealer for advanced help.
4.1 Checking If the Hardware Status Is OK or Not
Follow the steps below to verify the hardware status.
1.
Check the power line and LAN cable connections. Refer to “2.1 Hardware
Installation” for details.
2.
Turn on the router. Make sure the ACT LED blink once per second and the
correspondent LAN LED is bright.
3.
If not, it means that there is something wrong with the hardware status. Simply back
to “2.1 Hardware Installation” to execute the hardware installation again. And
then, try again.
29
4.2 Checking If the Network Connection Settings on Your
Computer Is OK or Not
Sometimes the link failure occurs due to the wrong network connection settings. After
trying the above section, if the link is stilled failed, please do the steps listed below to
make sure the network connection settings is OK.
For Windows
The example is based on Windows XP. As to the examples for other
operation systems, please refer to the similar steps or find support notes in
www.draytek.com.
1.
Go to Control Panel and then double-click on Network Connections.
2.
Right-click on Local Area Connection and click on Properties.
3.
Select Internet Protocol (TCP/IP) and then click Properties.
30
4.
Select Obtain an IP address automatically and Obtain DNS server address
automatically.
For MacOs
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Network.
3.
On the Network screen, select Using DHCP from the drop down list of Configure
IPv4.
31
4.3 Pinging the Router from Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might
need to use “ping” command to check the link status of the router. The most important
thing is that the computer will receive a reply from 192.168.1.1. If not, please check
the IP address of your computer. We suggest you setting the network connection as get IP
automatically. (Please refer to the section 4.2)
Please follow the steps below to ping the router correctly.
For Windows
1.
2.
Open the Command Prompt window (from Start menu> Run).
Type command (for Windows 95/98/ME) or cmd (for Windows NT/ 2000/XP). The
DOS command dialog will appear.
3.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “Reply from
192.168.1.1:bytes=32 time<1ms TTL=255” will appear.
4.
If the line does not appear, please check the IP address setting of your computer.
For MacOs (Terminal)
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Utilities.
3.
Double click Terminal. The Terminal window will appear.
4.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “64 bytes
from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear.
32
4.4 Checking If the ISP Settings are OK or Not
Open WAN >> Internet Access page and then check whether the ISP settings are set
correctly. Click WAN1 or WAN2 link to review the settings that you configured
previously.
For PPPoE Users
1.
Check if the Enable option is selected.
2.
Check if Username and Password are entered with correct values that you got from
your ISP.
33
34
For MPoA Users
1.
Check if the Enable option is selected.
2.
Check if DSL Modem Settings is set appropriately.
3.
Check if IP Address, Subnet Mask and Gateway are set correctly (must identify
with the values from your ISP) if you choose Specify an IP address.
4.5 Backing to Factory Default Setting If Necessary
Sometimes, a wrong connection can be improved by returning to the default settings. Try
to reset the router by software or hardware.
Warning: After pressing factory default setting, you will loose all settings
you did before. Make sure you have recorded all useful settings before you
pressing. The password of factory default is null.
Software Reset
You can reset the router to factory default via Web page.
Go to System Maintenance and choose Reboot System on the web page. The following
screen will appear. Choose Using factory default configuration and click OK. After few
seconds, the router will return all the settings to the factory settings.
35
Hardware Reset
While the router is running (ACT LED blinking), press the RST button and hold for more
than 5 seconds. When you see the ACT LED blinks rapidly, please release the button.
Then, the router will restart with the default configuration.
After restore the factory default setting, you can configure the settings for the router again
to fit your personal request.
36
4.6 Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send e-mail to
support@draytek.com.
37
Download PDF

advertising