Dual MXD105 Car Stereo System User Manual

MXD105
INSTALLATION/OWNER'S MANUAL
AM/FM Receiver with Detachable Face
MXD105 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
• Remove 2 transit screws located on top of the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting
sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain installations may require an installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
REMOVAL KEYS
MOUNTING SLEEVE
HEAD UNIT
TYPICAL FRONT-LOAD
DIN MOUNTING METHOD
2
INSTALLATION
MOUNTING KIT
OR DASHBOARD
MXD105 INSTALLATION
Wiring Diagram
Antenna
Connector
10 AMP
AGC Fuse
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse could
damage the radio.
The MXD105 uses one
10 amp AGC fuse located
in-line.
3
MXD105 OPERATION
Control Locations - Receiver
1
18
4
2
17
3
16
4
5
15
14
13
12
11
10
9
8
1
Release
10
Preset 3 / Intro
2
Power
11
Preset 2 / Random
3
Volume Knob
12
Preset 1 / Repeat
4
Audio / Menu
13
Display
5
USB Port
14
Tune Up
6
Auxiliary Input
15
Tune Down
7
Preset 6 / Folder Up
16
Band / Go Back
8
Preset 5 / Folder Down
17
Mode
9
Preset 4 / Play / Pause
18
Mute
7
6
MXD105 OPERATION
Control Locations - Remote
1
2
6
5
3
4
1
Power
4
Volume Down
2
Volume Up
5
Tune Down
3
Tune Up
6
Mode
5
MXD105 OPERATION
General Operation
Faceplate Removal
Power On/Off
Mode
Display
Press RELEASE and pull away from the left side to
remove. To re-install, insert right side of faceplate first
then push left side to secure.
Press or any other button to turn the unit on. Press
again to turn the unit off.
Press MODE to select between AM/FM, USB, SD or auxiliary input modes. Modes of operation are indicated in the
display. SD and USB modes will not appear unless an SD
Card is inserted or a USB device is connected.
The radio frequency (tuner mode) or MP3/WMA title/track
information (USB and SD modes) will be shown by default.
Press DISP to display the clock. The default display will
return after five seconds.
When in USB or SD mode, the display will alternate
between track number/elapsed time and available MP3/
WMA information, including file name, song title, artist
name, album name and folder name.
Reset
Set the Clock
Auxiliary Input
Volume
Preset EQ Curves
Press RESET upon initial installation or if abnormal operation occurs. Reset button is located behind the front panel.
Press DISP to display the clock, then press and hold DISP
until the hours will flash. Rotate the volume knob to adjust
the hours. Press the volume knob, and the minutes will
flash. Rotate the volume knob to adjust the minutes.
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the headphone output of an audio device, MP3 player, etc.
Adjust volume using the volume knob (00-40).
Press EQ to select between the following preset equalization curves: FLAT, POP, JAZZ, ROCK and OFF.
Note: Ability to manually adjust Bass and Treble settings
is disabled when a preset equalization curve is selected.
Setting equalization curves to OFF enables manual Bass
and Treble adjustments as outlined on page 7.
6
MXD105 OPERATION
General Operation
Audio / Menu
Press the volume knob to select between Bass, Treble,
Balance, Fader, Loudness, Distance and Stereo.
BASS
TREBLE
BALANCE
FADER
LOUDNESS
Bass
Press the volume knob until BAS appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
Treble
Press the volume knob until TRE appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
DISTANCE
STEREO
Balance
Press the volume knob until BAL appears.
Rotate the volume knob left/right to adjust.
10L (left) to 10R (right). "L=R" represents equal balance.
Fader
Press the volume knob until FAD appears.
Rotate the volume knob left/right to adjust.
10R (rear) to 10F (front) "F=R" represents equal balance.
Loudness
Press the volume knob until LOUD ON or LOUD OFF appears,
then rotate the volume knob to select desired option.
Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes.
Distance Tuning
From tuner mode only, press the volume knob until DX
or LOCAL appears, then rotate the volume knob to select
desired option. Selecting LOCAL programs the unit to stop at
only strong stations when seek tuning.
Stereo / Mono
From tuner mode only, press the volume knob until STEREO
or MONO appears, then rotate the volume knob to select
desired option. Selecting MONO can improve listening in
areas with a weak FM signal.
Audible Beep
Press and hold the volume knob until BEEP ON or BEEP
OFF appears, then rotate the volume knob to select desired
option. Activating this feature programs the unit to beep each
time certain buttons are pressed.
Area Selection
From tuner mode only, press and hold the volume knob
until BEEP ON or BEEP OFF appears. Press the volume knob
again to display AREA USA or AREA EURO, then rotate the
volume knob to select option appropriate for your location.
12/24-Hour Clock
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10.00). In European frequency spacing
mode, the clock will display 24-hour time (22.00).
7
MXD105 OPERATION
AM/FM Tuner Operation
Press TUNE nn or TUNE ll momentarily to seek to the
Seek Tuning
next strong station.
Press and hold TUNE nn or TUNE ll until "MANUAL"
Manual Tuning
appears, then press TUNE nn or TUNE ll momentarily
to change radio frequency up or down one step at a time.
Press and hold to advance quickly.
Band
Storing and Recalling
Station Presets
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
USB / SD Card Operation
Connecting a USB Device
(sold separately)
Inserting an SD Card
(sold separately)
To play MP3/WMA/WAV files from an SD card, insert an SD
card into the SD card slot with the label facing left. It will
click into place when properly inserted. To remove the card,
press in until it clicks, then pull to remove.
Playing Music
When a USB device is first connected, “LOAD” will appear in
the display and playback will begin momentarily. Depending
on the number of files and folders, it may take several
seconds for the device to begin playing. If no valid MP3/
WMA files are detected, “NO FILE” will be displayed and the
last mode will be resumed.
Track Select
Fast Forward and
Reverse
Pause
Displaying Information
8
To play MP3/WMA files from most USB mass storage
devices, line up the USB connector and insert the USB
device into the MXD105's USB port.
ll nn
Press TRACK
to skip to the beginning of the next
track. Press TRACK
to return to the beginning of the
current track. Pressing TRACK
again skips to the
beginning of the previous track.
ll
nn
nn on the remote
Press and hold TRACK
or TRACK
control to fast forward or reverse a track.
Press
Press
temporarily stop USB playback.
ll// IIII toagain
to resume playback.
ID3 tag and file/folder information will be automatically
changed during playback. Press DISP to view the clock.
Default display will resume after five seconds.
MXD105 OPERATION
USB / SD Card Operation
Repeat
Random
Intro Character Support
Media Compatibility
Press RPT to choose between:
• Current Song - Continuously repeats selected track.
• Current Folder - Continuously repeats all files in folder.
Press RDM to choose between:
• Off - Cancels RDM function.
• All Songs - Plays all tracks in random order.
• Current Folder - Plays all tracks in folder in random
order.
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• Off - Cancels the INT function.
• All Songs - Plays first 10 seconds of each track.
• Current Folder - Plays first 10 seconds of each track in
folder.
Maximum character display information
• Track name – 64 character maximum
• Directory name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
• *Album name – 64 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3/WMA file.
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
MP3/WMA playback sequence is based on order the files
are copied to the USB/SD device and begins in the root
folder. Any empty folders or folders that do not include MP3/
WMA files are skipped. Depending on your software, the
playback order may vary.
9
MXD105 OPERATION
USB / SD Card Operation
Playback Capacity
• Maximum number of files: 1024
• Maximum number of folders: 512
• Maximum number of folder levels (sub folders): 8
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note: Devices that exceed the maximum number of files or
folders may not function properly.
USB Device Compatibility
Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility. USB devices must be 32GB or
smaller in capacity to be compatible.
Additional MP3/WMA
Information
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
Sampling Frequency
Rates
MP3
8kHz ~ 48kHz
WMA
8kHz ~ 48kHz
Transfer Bit rates
MP3
WMA
8kbps ~ 320kbps constant
Variable bit rates
8kbps ~ 384kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
10
MXD105 INSTALLATION
Troubleshooting
Problem
Unit will not turn on (no power)
Unit has power (but no sound)
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Black wire not connected
Fuse blown
Speaker wires not connected
Check connections for proper
voltage (11~16VDC)
One or more speaker wires touching
each other or touching chassis ground
Check connection to ground
Replace fuse
Check connections at speakers
Insulate all bare speaker wires
from each other and chassis
ground
Unit blows fuses
Yellow or red wire touching chassis
ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
NO FILE appears on display
No playable MP3/WMA files found on
the device
Check the device for valid
MP3/WMA files
NO SUPPORT appears
on display
An invalid ID3 tag version is present
Version 1.0 to 2.0 ID3 tags are
supported.
Check for pinched wire
11
MXD105 OPERATION
Limited One Year Warranty
This warranty gives you specific legal
rights. You may also have other rights
which vary from state to state.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
Who is covered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered:
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
license conditions and copyright notices for
the software can be found via www.dualav.
com.
12
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
2. If you require service during the
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
authorized service center.
3. Please describe your problem in
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
4. For more information and for the
location of the nearest authorized
service center please contact us by one
of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
or imputed. No person or representative
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
MXD105 OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
13
MXD105 OPERATION
Specifications
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 10dBf
50dB quieting sensitivity: 25dbu
Stereo separation @ 1kHz: >30dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: <42dBu
Frequency response: 30Hz-2.2kHz
General
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts RMS
Dimensions: 7" x 7" x 2" (178 x 178 x 50 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
14
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 70dBA (reference: 1 watt into 4 ohms)
MXD105 OPERATION
Notes
15
Dual Electronics Corp.
Toll Free: 1-866-382-5476
9AM-5PM EST, Monday-Friday
www.dualav.com
©2014 Dual Electronics Corp. All rights reserved.
Other trademarks and trade names are those of their respective owners.
NSA0314-V01