Ducati 1000DS Motorcycle User Manual

DUCum_1000DS####03_###e.book Page 1 Wednesday, March 12, 2003 4:33 PM
Owner's manual
E
DUCATIMULTISTRADA
1000DS
1
DUCum_1000DS####03_###e.book Page 2 Wednesday, March 12, 2003 4:33 PM
E
2
DUCum_1000DS####03_###e.book Page 3 Wednesday, March 12, 2003 4:33 PM
Hearty welcome among Ducati fans! Please accept our
best compliments for choosing a Ducati motorcycle. We
think you will ride your Ducati motorcycle for long journeys
as well as short daily trips. Ducati Motor Holding S.p.A.
wishes you smooth and enjoyable riding.
We are steadily doing our best to improve our "Technical
Assistance" service. For this reason, we recommend you
to strictly follow the indications given in this manual,
especially for motorcycle running-in. In this way, your
Ducati motorbike will surely give you unforgettable
emotions. Please contact our authorised service centres
to have your motorcycle repaired or if you simply need
advice.
Enjoy your ride!
Note
Ducati Motor Holding S.p.A. declines any liability
whatsoever for any mistakes incurred in drawing up this
manual. The information contained herein is valid at the
time of going to print. Ducati Motor Holding S.p.A.
reserves the right to make any changes required by the
future development of the above-mentioned products.
E
For your safety, as well as to preserve the warranty,
reliability and worth of your motorcycle, use original Ducati
spare parts only.
Warning
This manual forms an integral part of the motorcycle
and - in the event the motorcycle is resold - must always
be handed over to the new owner.
3
DUCum_1000DS####03_###e.book Page 4 Wednesday, March 12, 2003 4:33 PM
TABLE OF CONTENTS
E
General 6
Warranty 6
Symbols 6
Useful information for safe riding 7
Carrying the maximum load allowed 8
Identification data 9
Controls 10
Position of motorcycle controls 10
Instrument panel 11
LCD unit functions 12
LCD - Parameter setting/display 14
Backlighting function 21
Pilot lights brightness function 21
Auto-off headlight function 21
The immobilizer system 21
Keys 22
Code card 23
Procedure to disable immobilizer engine block through
throttle twistgrip 24
Duplicate keys 25
Ignition switch and steering lock 26
4
Left switch 27
Clutch lever 28
Right switch 29
Throttle twistgrip 29
Front brake lever 30
Rear brake pedal 31
Gear change pedal 31
Setting the gear change and rear brake pedals 32
Main components and devices 34
Location 34
Tank filler plug 35
Passenger seat catch and helmet hook 36
Glove compartment lock 37
Side stand 38
Front fork adjusters 39
Rear shock absorber adjusters 41
Rear-view mirrors adjustment 42
Motorcycle trim adjustment 43
Directions for use 44
Running-in recommendations 44
Pre-ride checks 46
Starting the engine 47
Moving off 49
Braking 49
Stopping the motorcycle 50
Parking 50
Refuelling 51
Tool kit and accessories 52
DUCum_1000DS####03_###e.book Page 5 Wednesday, March 12, 2003 4:33 PM
Main maintenance operations 53
Removing the fairing 53
Checking brake and clutch fluid level 58
Checking brake pads for wear 60
Lubricating joints 61
Throttle cable free play adjustment 62
Charging the battery 63
Checking the drive chain tension 64
Chain lubrication 65
Replacing headlamp bulbs 66
Changing the front direction indicators bulbs 70
Changing the rear direction indicators bulbs 71
Changing the number plate and stop light bulbs 72
Beam setting 74
Tubeless tyre pressure 75
Checking engine oil level 77
Cleaning and replacing the spark plugs 78
Cleaning the motorcycle 79
Storing the bike away 79
Important notes 79
Brakes 85
Frame 86
Wheels 86
Tyres 86
Suspensions 87
Available in the following colors: 87
Electric system 88
For United States of America version Only
Routine maintenance record
93
102
E
Technical data 80
Overall dimensions 80
Weights 80
Engine 82
Timing system 82
Performance data 83
Spark plugs 83
Exhaust system 83
Transmission 84
5
DUCum_1000DS####03_###e.book Page 6 Wednesday, March 12, 2003 4:33 PM
GENERAL
E
Warranty
In your own interest, and in order to guarantee product
reliability, you are strongly advised to refer to a Ducati
Dealer or Authorised Workshop for any servicing requiring
particular technical expertise. Our highly skilled staff have
access to the implements required to perform any
servicing job at best, and use Ducati original spare parts
only as the best guarantee for full interchangeability,
smooth running and long life.
All Ducati motorcycles come with a "Warranty Card". The
warranty does not apply to the motorcycles used in
competitions. No motorcycle part may be tampered with,
altered, or replaced with parts other than original Ducati
spare parts during the warranty period, or the warranty will
be automatically invalidated.
Symbols
Ducati Motor Holding S.p.A. advises you to read this
booklet carefully so as to become familiar with your
motorcycle. In case of any doubts, please call a Ducati
Dealer or Authorised Workshop. The information
contained herein will prove useful on your trips - and
Ducati Motor Holding S.p.A. wishes you smooth,
enjoyable riding - and will help you keep the performance
of your motorcycle unchanged for a long time.
Warning
Failure to comply with these instructions may put you
at risk and lead to severe injury or death.
Important
Possibility of damaging the motorcycle and/or its
components.
Note
Additional information on the job being carried out.
The terms right and left are referred to the motorcycle
viewed with respect to the direction of travel.
6
DUCum_1000DS####03_###e.book Page 7 Wednesday, March 12, 2003 4:33 PM
Useful information for safe riding
Warning
Read this section before riding your motorcycle.
Accidents are frequently due to inexperience. Always
make sure you have your licence with you when riding;
you need a valid licence to be entitled to ride your
motorcycle.
Do not lend your motorcycle to inexperienced riders or
who do not hold a valid licence.
Both rider and pillion passenger must always wear a
safety helmet.
Wear proper clothing, with no loose items or accessories
that may become tangled in the controls or limit your zone
of vision.
Never start or run the engine indoors. Exhaust gases are
poisonous and may lead to loss of consciousness or even
death within a short time.
Both rider and pillion passenger should keep their feet on
the footpegs when the motorcycle is in motion.
Always hold handlebar firmly with both hands so you will
be ready for sudden changes of direction or in the road
surface. The pillion passenger should always hold on to
the suitable grab handle at the rear seat with both hands.
Ride within the law and observe national and local rules.
Always respect speed limits where these are posted.
However, always adjust your speed to the visibility, road
and traffic conditions you are riding in.
Always signal your intention to turn or pull to the next lane
in good time using the suitable turn indicators.
Be sure you are clearly visible and do not ride within the
blind spot of vehicles ahead.
Be very careful when tackling road junctions, or when
riding in the areas near exits from private grounds, car
parks or on slip roads to access motorways.
Always turn off the engine when refuelling.
Be extremely careful not to spill fuel on the engine or on
the exhaust pipe when refuelling.
Do not smoke when refuelling.
While refuelling, you may inhale noxious fuel vapours.
Should any fuel drops be spilled on your skin or clothing,
immediately wash with soap and water and change your
clothing.
Always remove the key when you leave your motorcycle
unattended.
The engine, exhaust pipes, and mufflers stay hot for a long
time.
Warning
The exhaust system might be hot, even after engine
is switched off; pay particular attention not to touch
exhaust system with any body part and do not park the
vehicle next to inflammable material (wood, leaves etc.).
Park your motorcycle where no one is likely to hit it and
use the side stand.
Never park on uneven or soft ground or your motorcycle
may fall over.
7
E
DUCum_1000DS####03_###e.book Page 8 Wednesday, March 12, 2003 4:33 PM
Carrying the maximum load allowed
Your motorcycle is designed for long-distance riding,
carrying the maximum load allowed in full safety.
Even weight distribution is critical to preserving these
safety features and avoiding trouble when performing
sudden manoeuvres or riding on bumpy roads.
E
Information about carrying capacity
The total weight of the motorcycle in running order
including rider, pillion passenger, luggage and additional
accessories should not exceed 410 Kg.
8
Arrange your luggage or heavy accessories in the lowest
possible position and close to motorcycle centre.
Be sure to secure the luggage to the supports provided on
the motorcycle as firmly as possible. Improperly secured
luggage may affect stability.
Never fix bulky or heavy objects to the handlebar or to the
front mudguard as this would affect stability and cause
danger.
Do not insert any objects you may need to carry into the
gaps of the frame as these may foul moving parts.
Make sure the tyres are inflated to the proper pressure
indicated at page 75 and that they are in good condition.
DUCum_1000DS####03_###e.book Page 9 Wednesday, March 12, 2003 4:33 PM
Identification data
All Ducati motorcycles have two identification numbers,
for frame (fig. 1) and engine (fig. 2).
Frame number
Engine number
Note
These numbers identify the motorcycle model and
should always be indicated when ordering spare parts.
E
fig. 1
fig. 2
9
DUCum_1000DS####03_###e.book Page 10 Wednesday, March 12, 2003 4:33 PM
CONTROLS
6
E
1
4
7
Warning
This section details the position and function of all the
controls you need to drive your motorcycle. Be sure to
read this information carefully before you use the controls.
3
Position of motorcycle controls (fig. 3)
1)
2)
3)
4)
5)
6)
7)
8)
9)
Instrument panel.
Key-operated ignition switch and steering lock.
Left switch.
Right switch.
Throttle twistgrip.
Clutch lever.
Front brake lever.
Rear brake pedal.
Gear change pedal.
5
2
9
8
fig. 3
10
DUCum_1000DS####03_###e.book Page 11 Wednesday, March 12, 2003 4:33 PM
Instrument panel
1) LCD, (see page 12).
2) Control buttons A and B.
Buttons used to display and set instrument panel
parameters.
3) Immobilizer IMMO
indicator (amber).
The indicator stays on in case of wrong key code or key
code not recognised; it flashes in case an immobilizer
system warning was reset with the procedure to override
the immobilizer with the throttle twistgrip (see page 24).
1
2
Important
The instrument panel allows to making diagnosis on
the electronic injection/ignition system.
These menus are for the trained personnel only; do not
use them for any reason. Should you accidentally enter
this function, turn the key to OFF and contact an
authorised Ducati Service Center for the necessary
inspections.
4) Revolution counter (rpm).
Shows the engine rotation speed/minute.
E
3
km/h
miles
mph
km/L
mpgal
4
fig. 4
11
DUCum_1000DS####03_###e.book Page 12 Wednesday, March 12, 2003 4:33 PM
LCD unit functions
Warning
Stop the motorcycle before using the instrument
panel controls. Never operate the instrument panel
controls while riding.
1) Oil temperature warning light.
This function indicates engine oil temperature.
E
Important
Never use the vehicle when the temperature reaches
max. value or the engine might damage.
2) Clock.
3) Tachometer.
This function indicates vehicle speed.
12
4) Auxiliary display.
This function indicates odometer, trip meter, average
speed, instant fuel consumption, average fuel
consumption, fuel used, range and residual fuel quantity,
in this sequence.
5) EOBD light
(amber).
When on, this light is used by the control unit to signal the
presence of errors and the consequent engine disabling.
It is also used as a reference light during the immobilizer
overriding procedure with the throttle twistgrip.
If there are no errors, the light should turn on when the
ignition switch is turned ON and should go off after a few
seconds (usually 1.8 - 2 seconds).
DUCum_1000DS####03_###e.book Page 13 Wednesday, March 12, 2003 4:33 PM
6) Indicators repeater light
(green).
Comes on and flashes when a turn indicator is on.
1
2
7) Engine oil pressure light
(red).
Comes on when engine oil pressure is too low. It briefly
comes on when the ignition is switched to ON and
normally goes out a few seconds after engine starts.
It may shortly come on when the engine is very hot,
however, it should go out as the engine revs up.
13
3
12
km/h
miles
mph
km/L
mpgal
11
4
Important
If this light (7) stays on, stop the engine or it may
suffer severe damage.
E
10
8) Neutral light N (green).
Comes on when in neutral position.
9) High beam light
(blue).
Comes on when high beam is on.
10)Fuel warning light (yellow).
Comes on when there are about 6.5 liters fuel left in the
tank.
11) Fuel Display.
This function indicates the quantity of fuel in the fuel tank.
When the last bar stays on (flashing), the low fuel light (10)
comes on.
9
8
7
6
5
fig. 5
12)Beam vertical adjustment indicator.
The pilot light comes on to signal that the user has entered
the beam vertical setting mode.
13)Service warning.
The light comes on to signal that the vehicle has covered
the distance corresponding to a Scheduled Maintenance
interval. The light keeps flashing until the vehicle has
travelled 50 km after hitting the service interval. Then it
stays on permanently. The system shall be reset by the
DUCATI Authorised Service Center that has serviced the
vehicle.
13
DUCum_1000DS####03_###e.book Page 14 Wednesday, March 12, 2003 4:33 PM
LCD - Parameter setting/display
When turning the key from OFF to ON (Key-ON) the
instrument panel carries out a Check of the whole
instruments: indexes, displays and pilot lights (see fig. 6).
E
Oil temperature (fig. 7)
This function indicates engine oil temperature.
When temperature is below 40 °C/104 °F a flashing "LO"
message is displayed.
When oil temperature is between 40 °C/104 °F and 170
°C/338 °F temperature measurement is displayed.
When oil temperature goes over 170 °C/338 °F a flashing
"HI" message is displayed.
40 ˚C/104 ˚F
39 ˚C/102 ˚F
OFF
CHECK 1
km/h
miles
mph
km/L
mpgal
170 ˚C/338 ˚F
171 ˚C/340 ˚F
CHECK 2
ON
km/h
fig. 7
14
fig. 6
DUCum_1000DS####03_###e.book Page 15 Wednesday, March 12, 2003 4:33 PM
Note
If the sensor measuring the temperature is
disconnected, a string of dashes "- - -" is displayed.
Clock setting function
Hold down button (A, see page 11) for 2 seconds, the
wording AM begins to flash. If button (B) is pressed again,
PM begins to flash; press button (B) to go back to previous
step. Press button (A) to confirm and start setting hours
that shall begin to flash.
Use button (B) to change hour value. If button (B) is
pressed for more than 5 seconds, fast scroll is activated.
Press button (A) to confirm and start setting minutes. Use
button (B) to set minutes. Press button (A) to confirm and
exit clock setting mode and go back to normal operation.
Auxiliary display functions (fig. 8)
Press button (B) with the key on ON to scroll down the
following functions, in sequence:
-
Odometer
TRIP meter
Average speed
Instant fuel consumption
Average consumption
Fuel used
Range
Digital fuel level indication
km
miles
km
miles
ODOMETER
TRIP METER
km/h
mph
km/L
mpgal
km/L
mpgal
L
gal
km
miles
L
gal
AVERAGE SPEED
E
INSTANT FUEL CONSUMPTION
AVERAGE CONSUMPTION
FUEL USED
RANGE
DIGITAL FUEL LEVEL INDICATION
fig. 8
15
DUCum_1000DS####03_###e.book Page 16 Wednesday, March 12, 2003 4:33 PM
"Odometer" indication (fig. 9)
Indicates total distance covered by the vehicle.
E
"TRIP meter" indication
This function indicates the distance covered since the
meter was last reset. It is possible to reset this indication
by entering the relevant function and holding down button
(A, see page 11), for at least 2 seconds. When a value of
9999.9 km (or miles) is reached, the display will
automatically reset.
km
miles
km
miles
"Average speed" indication
This function indicates vehicle average road speed.
Average speed calculation is based on the distance
travelled since the "TRIP meter" was last reset.
"Instant fuel consumption" indication
This function indicates the instant consumption of the
vehicle when in motion. When the vehicle is stopped with
engine running, a string of dashes is displayed "- - . -". With
vehicle stopped and engine off "0.0" is displayed.
km/h
mph
km/L
mpgal
fig. 9
16
DUCum_1000DS####03_###e.book Page 17 Wednesday, March 12, 2003 4:33 PM
"Average consumption" indication (fig. 10)
This function indicates the vehicle average consumption
when in motion. The calculation is based on the distance
travelled since the "TRIP meter" was last reset. When the
vehicle is stopped, either with the engine off or running,
the last value stored is displayed until indication is
refreshed.
"Fuel used" indication
This function indicates the fuel used by the vehicle to travel
the distance. The calculation is based on the distance
travelled since the "TRIP meter" was last reset. When
indication exceeds 9999.9 liters (2201.9 Imp. gal. - 2641.9
US gal.), the display shows a string of dashes "- - . -".
km/L
mpgal
E
L
gal
km
miles
L
gal
fig. 10
17
DUCum_1000DS####03_###e.book Page 18 Wednesday, March 12, 2003 4:33 PM
E
"Range" indication
This function indicates how far the vehicle can travel using
the fuel left in the tank. When this display function is not
selected, the display automatically switches to "Range"
indication as soon as the LOW FUEL LIGHT (10, fig. 5)
comes on and the display shows a string of dashes "- - . -"
and the indication for 10 seconds. Range indication is then
turned on automatically every 60 seconds while the low
fuel light stays on.
When the vehicle is stopped, either with the engine off or
running, the last value stored is displayed until indication is
refreshed.
Note
The value is refreshed every10 seconds, the
tolerance is 0.5 km.
"Digital fuel level" indication
This function indicates how much fuel is left in the fuel
tank.
When the LOW FUEL LIGHT (10, fig. 5) comes on, the
display shows a string of dashes "- - . -" and the fuel pump
symbol begins to flash.
Note
This vehicle is equipped with a long fuel tank, fuel
level indication might be slightly altered when riding up- or
downhill for a certain period.
18
DUCum_1000DS####03_###e.book Page 19 Wednesday, March 12, 2003 4:33 PM
Beam vertical adjustment (fig. 11)
This function allows headlight beam height setting.
To enter this function, hold down button (B, see page 11)
and turn the key to ON; the display shows a value (fig. 11a)
corresponding to beam position and the pilot light on the
display (12, fig. 5) comes on.
Use buttons (A) and (B), respectively, to lower or raise the
beam. Range available is from position "3" (max. beam
height) to position "-3" (min. beam height).
Turn the key to OFF to exit the function. While exiting
setting mode, the selected beam position is stored.
E
fig. 11
B
B
B
A
A
A
A
A
A
B
B
B
fig. 11a
19
DUCum_1000DS####03_###e.book Page 20 Wednesday, March 12, 2003 4:33 PM
E
Special selection function: vehicle model and unit of
measurement (fig. 12)
The control unit automatically informs the instrument
panel about the vehicle model and unit of measurement to
be displayed; hold down buttons (A) and (B) and turn
ignition switch from OFF to ON to force the system and
change these parameters. The display shows vehicle
model and version in flashing mode. Press button (B) to
display in sequence all possible settings. To save the
setting chosen hold down button (A) for at least 5
seconds, until OFF is displayed, then turn the key to OFF.
Note
When this function is activated, vehicle ignition is
inhibited.
fig. 12
20
DUCum_1000DS####03_###e.book Page 21 Wednesday, March 12, 2003 4:33 PM
Backlighting function
Instrument panel backlighting is active only if the parking
light or the low/high beam is on.
In this case the instrument panel automatically turns on or
off the backlighting, thanks to some sensors measuring
light condition and ambient temperature.
Pilot lights brightness function
This function is active only if the parking light or the low/
high beam is on.
Pilot lights brightness is automatically adjusted by the
instrument panel according to the outer light measured.
The immobilizer system
For improved anti-theft protection, the motorcycle is
equipped with an IMMOBILIZER, an electronic system
that inhibits engine operation whenever the ignition switch
is turned off.
Accommodated in the handgrip of each ignition key is an
electronic device that modulates an output signal. This
signal is generated by a special antenna incorporated in the
switch when the ignition is turned on and changes every
time. The modulated signal acts as a "password" and tells
the CPU that an "authorised" ignition key is being used to
start up the engine. When the CPU recognises the signal,
it enables engine start-up.
Auto-off headlight function
This function allows you to reduce current consumption from
the battery, by automatically managing headlight switching-off.
The device is enabled in two instances:
- If the key is turned from OFF to ON and no attempt is
made to start the engine. After 60 seconds, the
headlight is switched off and will be turned on only
upon the following Key-ON.
- After having used the bike, with headlight on, if the
engine is stopped via the ENGINE KILL switch (2, fig.
19), after 60 seconds from engine stop, the headlight is
turned off and will be turned on upon the following
engine start-up.
Note
While starting the engine, the system switches off
the headlight and turns it back on again after engine has
started, or anyway when the button (3, fig. 19) is released.
21
E
DUCum_1000DS####03_###e.book Page 22 Wednesday, March 12, 2003 4:33 PM
Keys (fig. 13)
The Owner receives a set of keys comprising:
- 1 RED key (A)
- 2 BLACK keys (B)
B
A
Warning
Red key has a rubber cover for preserving it in perfect
conditions and avoiding contact with other keys. Never
remove this protection unless really needed.
E
The black keys are regular ignition keys and are used to:
- start up the engine
- open the fuel tank filler plug
- open the seat lock
- release the pillion seat lock.
The red key performs the same functions as the black
keys, and is also used to wipe off and re-program other
black keys, if needed.
Warning
Any important shock might damage the electronic
components fitted into the key.
22
1
fig. 13
Note
The three keys have a small plate (1) attached that
reports their identification number.
Warning
Keep the keys in different places. Store the plate (1)
and the red key in a safe place.
It is also recommended to use always the same black key
to start the bike.
DUCum_1000DS####03_###e.book Page 23 Wednesday, March 12, 2003 4:33 PM
Code card
A CODE CARD (fig. 14) is supplied together with the keys,
it indicates the electronic code (A, fig. 15) to be used in
case the engine is disabled and will not start up after the
key-ON.
Warning
Keep the CODE CARD in a safe place. However, it is
advisable to keep the electronic code printed on the CODE
CARD handy when you ride your motorcycle, in case it is
necessary to remove engine block through the procedure
that uses the throttle twistgrip (see page 24).
In case of faulty immobilizer system, this procedure gives
the chance to disable "engine block" function -signalled by
the orange EOBD warning light (5, fig. 5).
E
fig. 14
A
fig. 15
23
DUCum_1000DS####03_###e.book Page 24 Wednesday, March 12, 2003 4:33 PM
Procedure to disable immobilizer engine block
through throttle twistgrip
E
1) Turn the key to ON and fully open throttle. Keep it
open. The EOBD warning light turns off after 8
seconds.
2) Release the throttle as soon as the EOBD warning
light turns off.
3) EOBD pilot light will flash. Count a number of flashes
corresponding to the first figure of the code printed on
the CODE CARD, open full throttle and keep the
position for 2 seconds, then release. In this way the
input of one figure is acknowledged, EOBD pilot light
comes on and stays on for 4 seconds. Carry out the
same procedure for the following figures of the code.
Failure to do so will cause the EOBD pilot light to flash
20 times, then it will stay on. This means that the
procedure has been aborted. It will be necessary to
turn the key to OFF and restart from point 1.
4) Repeat operations described in point 3 up to the last
figure of the code.
24
5) Release the throttle twistgrip, if the code is correct the
following two conditions may occur:
A) the EOBD warning light shall flash signalling that
engine block has been disabled. The warning light turns
off after 4 seconds or if engine revolutions go over the
limit value of 1000 rpm.
B) the IMMO light (3, fig. 4) flashes until engine rpm
get above 1000 rpm, or until engine is re-started.
6) If the code is NOT correct, the EOBD warning light
and the IMMO light stay on and it is then possible to
repeat the procedure, starting from point 2, as many
times as necessary (infinite).
Note
Should the throttle twistgrip be released before the
set time, the warning light turns on again. It is then
necessary to bring the key to OFF and restart the
procedure from point 1.
DUCum_1000DS####03_###e.book Page 25 Wednesday, March 12, 2003 4:33 PM
Operation
When the ignition key is turned to OFF, the immobilizer
inhibits engine operation.
When the ignition key is turned back to ON to start the
engine (Key-ON), the following happens:
1) if the CPU recognised the code, the IMMO light on the
instrument panel will flash briefly. This means that the
immobilizer system has recognised the key code and
enabled engine ignition. When you press the
start
button, the engine will start up.
2) If the IMMO light stays on, it means that the code has
not been recognised. When this is the case, turn the
ignition key back to OFF and then to ON again. If the
engine still does not start, try with another black key.
If the other key does not work out either, contact the
DUCATI Service network.
3) Should the IMMO pilot light still be flashing, it means
that an immobilizer system fault was reset (e.g. with
the overriding procedure through throttle grip).
Duplicate keys
If you need any additional key, contact the DUCATI Service
network with all the keys you have left and your CODE
CARD.
DUCATI Service will program new keys and re-program
your original keys, up to 8 keys in total.
You may be asked to identify yourself as the legitimate
owner of the motorcycle. Be sure you have any
documents you might need to this end ready.
The codes of any keys not submitted will be wiped off
from the memory to make those keys unserviceable in
case they have been lost.
Note
If you sell your motorcycle, do not forget to give all
keys and the CODE CARD to the new owner.
Important
Use only one key during the procedure. Failure to do
so might prevent the system from recognizing the code of
the key in use.
25
E
DUCum_1000DS####03_###e.book Page 26 Wednesday, March 12, 2003 4:33 PM
Ignition switch and steering lock (fig. 16)
It is located in front of the steering head and has four
positions:
A) ON: lights and engine on;
B) OFF: lights and engine off;
C) LOCK: steering is locked;
D) P: parking light is ON and steering is locked.
26
FF
ON
PUS
H
O
K
Important
The motorcycle is equipped with an energy-saving
CPU. If the key stays ON for a long period but the ignition
button is not pressed within 15 seconds, the CPU will stop
operating to avoid current absorption. To restore the
system move the key to OFF and then to ON again.
A
B
C
LO
E
Note
To move the key to the last two positions, press it
down before turning it. Switching to (B), (C) and (D), you
will be able to take the key out.
N
IO
P
NIT
IG
C
D
fig. 16
DUCum_1000DS####03_###e.book Page 27 Wednesday, March 12, 2003 4:33 PM
Left switch (fig. 17)
1) Dip switch, light dip switch, two positions:
- position
= low beam on;
- position
= high beam on.
2) Switch
= 3-position turn indicator:
- centre position = OFF;
- position
= left turn;
- position
= right turn.
To reset turn indicators, push in when switch is back to
central position .
3) Button
= warning horn.
4) Button
= high-beam flasher.
5
4
1
E
2
3
fig. 17
5) Button
= Emergency stop flashers
Press this button to turn on all direction indicators at
the same time.
Press it again to turn them off.
Note
When devices (1), (2), (4) and (5) are activated, the
relevant pilot lights on the instrument panel turn on (see
page 13).
27
4
2
1
E
Clutch lever (fig. 18)
Lever (1) disengages the clutch. It features a dial adjuster
(2) for lever distance from the twistgrip on handlebar.
To set lever distance from twistgrip, push lever (1) fully
forward and turn the dial adjuster (2) to one of its four
positions. Remember that position no. 1 gives maximum
distance between lever and twistgrip, whereas lever and
twistgrip are closest when adjuster is set to position no. 4.
When you pull in the lever (1), you will disengage the
engine from the gearbox and therefore from the driving
wheel. Using the clutch properly is essential to smooth
riding, especially when moving off.
3
DUCum_1000DS####03_###e.book Page 28 Wednesday, March 12, 2003 4:33 PM
2
Warning
Set clutch lever when motorcycle is stopped.
Important
Using the clutch properly will avoid damage to
transmission parts and spare the engine.
Note
It is possible to start the engine with side stand fully
down and the gearbox in neutral. When starting the bike
with a gear engaged, pull the clutch lever (in this case the
side stand must be up).
fig. 18
28
DUCum_1000DS####03_###e.book Page 29 Wednesday, March 12, 2003 4:33 PM
Right switch (fig. 19)
1) Switch, light switch, three positions:
- right position
= lights off;
- centre position
= front and rear parking lights,
- number plate and instrument panel lights on;
- left position
= headlight, front and rear parking
lights, number plate and instrument panel lights on.
Throttle twistgrip (fig. 19)
The twistgrip (4) on the right handlebar opens the throttles.
When released, it will spring back to the initial position
(idling speed).
Note
This device is not fitted on the Australia and Japan
versions.
E
2) Switch for engine stop, two positions:
- position
(RUN) = run.
- position
(OFF) = stop.
Warning
This switch is mainly intended for use in emergency
cases when you need to stop the engine quickly. After
stopping the engine, return the switch to the
position
to enable starting.
3) Button
2
4
= engine start.
3
1
fig. 19
29
DUCum_1000DS####03_###e.book Page 30 Wednesday, March 12, 2003 4:33 PM
3
To adjust, keep lever (1) completely extended, turn knob
(2) and set it to one of the four available positions.
Consider that:
position no. 1 corresponds to the maximum distance
between lever and twistgrip, while position no. 4
corresponds to the minimum distance.
4
E
2
1
Front brake lever (fig. 20)
Pull in the lever (1) towards the twistgrip to operate the
front brake. The system is hydraulically operated and you
just need to pull the lever gently.
The control lever features a dial adjuster (2) for lever
distance from the twistgrip on handlebar.
2
Warning
Front brake lever adjustment is to be carried out
when the bike is stopped.
1
fig. 20
30
DUCum_1000DS####03_###e.book Page 31 Wednesday, March 12, 2003 4:33 PM
Rear brake pedal (fig. 21)
Push down on the pedal (1) to apply the rear brake. The
system is hydraulically operated and therfore only a
minium pressure is required.
1
E
fig. 21
Gear change pedal (fig. 22)
Gearchange pedal features a center rest position N, with
automatic return; this condition is signalled by the pilot
light N (8, fig. 5) on the instrument panel turning on.
The pedal can be moved:
down = push down on the pedal to engage 1st gear and to
shift down. The N light will go out.
up = lift the pedal to engage the 2nd gear and then the 3rd,
4th, 5th and 6th gear.
Each time you move the pedal you will engage the next
gear.
6
5
4
3
2
N
1
fig. 22
31
DUCum_1000DS####03_###e.book Page 32 Wednesday, March 12, 2003 4:33 PM
Setting the gear change and rear brake pedals
The gear change and rear brake pedals can be adjusted to
suit the preferred riding position of each rider with respect
of the pertinent footpeg.
To make these adjustments, follow the procedure
described.
E
Gearchange pedal (fig. 23)
Lock rod (1) by fitting an open-end wrench to socket (2),
and loosen lock nut (3).
Slacken screw (4), so to be able to remove rod (1) from the
gearchange lever.
Turn rod (1) by fitting a wrench to socket (2), set pedal in
the desired position.
Use screw (4) to secure the gearchange lever to rod (1).
Tighten lock nut (3) against rod (1).
32
3
1
2
fig. 23
DUCum_1000DS####03_###e.book Page 33 Wednesday, March 12, 2003 4:33 PM
Rear brake pedal (fig. 23a)
Loosen check nut (5).
Turn pedal travel adjusting screw (6) until pedal is in the
desired position.
Tighten check nut (5).
Work pedal by hand to make sure it has 1.5 - 2 mm free
play before brake begins to bite.
If not so, set the length of cylinder linkage as follows.
Loosen the check nut (7) on cylinder linkage.
Tighten linkage (8) into fork (9) to increase play, or unscrew
linkage to reduce it.
Tighten check nut (7) and check pedal free play again.
8
7
9
E
5
6
fig. 23a
33
DUCum_1000DS####03_###e.book Page 34 Wednesday, March 12, 2003 4:33 PM
MAIN COMPONENTS AND DEVICES
6
8
Location (fig. 24)
E
1)
2)
3)
4)
5)
6)
7)
8)
9)
Tank filler plug.
Pillion seat catch and helmet hooks.
Glove compartment catch.
Side stand.
Front fork adjusters.
Rear shock absorber adjusters.
Rear-view mirrors.
Silencer and exhaust pipes.
Catalyser (not on USA version).
5
8
4
3
5
7
9
6
2
8
Warning
The exhaust system can be hot even after engine has
been turned off; be careful not to touch the exhaust
system with any part of your body and do not park the
vehicle next to flammable material (such as wood, leaves
and so on).
7
5
1
fig. 24
34
DUCum_1000DS####03_###e.book Page 35 Wednesday, March 12, 2003 4:33 PM
Tank filler plug (fig. 25)
1
Opening
Lift the protection lid (1) and fit the ignition key into the
lock. Turn the key clockwise 1/4 turn to unlock. Lift the
plug (2, fig. 25a).
Closing
Refit the plug (2) with the key in it and push it down into
its seat.
Turn the key anticlockwise to its initial position and take it
out. Close the lock protection lid (1).
E
Note
The plug can only be closed with the key in.
Warning
Always make sure you have properly refitted (see
page 51) and closed the plug after each refuelling.
fig. 25
2
1
fig. 25a
35
DUCum_1000DS####03_###e.book Page 36 Wednesday, March 12, 2003 4:33 PM
Passenger seat catch and helmet hook
Opening (fig. 26)
Insert the key in lock (1) and turn it clockwise until you hear
the seat catch click in place.
Lift the seat rear end (2) and pull it backward to slide it out
from the front supports.
E
Closing
Rest the seat on fuel tank retainers, pull it back until you
hear it click in place.
Push on the seat rear end until hearing the catch click in
place.
Make sure the seat is properly secured, try pushing the
seat upward.
OPEN
1
fig. 26
The hook for the helmet cable is located under the
passenger seat. Route cable (A) in the helmet and insert
the ends in the hook. Leave helmet hanging on the left
side (fig. 27) and refit the seat to secure it in place.
Warning
This system is intended to lock your helmet safely
when you park your motorcycle. Never leave the helmet
hanging from the hook when riding or it may get in the way
and make you lose control of the motorcycle.
The cable is to be fitted on the left side. If fitted in any
other position, it will prevent the seat from closing.
A
fig. 27
36
DUCum_1000DS####03_###e.book Page 37 Wednesday, March 12, 2003 4:33 PM
Glove compartment lock
To open glove compartment door, insert the key into lock
(1) and rotate it counterclockwise until hearing the catch
unlock (fig. 28).
Open the door (fig. 28a) to gain access to the glove
compartment where the Owner's manual and the tool kit
are (see page 52).
Important
Do not store heavy or metal parts in the glove
compartment or they might move when the bike is running
thus making the vehicle unstable.
Push the door at the catches to close it, until hearing a
click.
Remove the key.
OPEN
1
E
fig. 28
fig. 28a
37
DUCum_1000DS####03_###e.book Page 38 Wednesday, March 12, 2003 4:33 PM
Side stand (fig. 29)
E
Important
Before lowering the side stand, make sure that the
bearing surface is hard and flat.
Do not park on soft or pebbled ground or on asphalt melt
by the sun heat and similar or the motorcycle may fall over.
When parking in downhill road tracts, always park the
motorcycle with its rear wheel facing downhill.
To pull down the side stand, hold the motorcycle
handlebar with both hands and push down on the thrust
arm (1) with your foot until it is fully extended. Tilt the
motorcycle to the left until the side stand end is resting on
the ground.
Note
It is possible to start the engine with the side stand
down, if the gearbox is in neutral position.
Warning
Do not sit on the motorcycle when it is supported on
the side stand.
To move the side stand to its rest position (horizontal
position), tilt the motorcycle to the right and, at the same
time, lift the thrust arm (1) with your foot.
Check for proper operation of the stand mechanism (two
springs, one into the other) and the safety sensor (2) which
communicates the stand position to the engine CPU at
regular intervals.
A 3A fuse fitted on the side of the battery protects this
system (see page 89).
1
2
fig. 29
38
DUCum_1000DS####03_###e.book Page 39 Wednesday, March 12, 2003 4:33 PM
Front fork adjusters
The front fork used has rebound and compression
damping adjuster as well as a spring preload adjuster.
1
2
2
1
This adjustment is done using the outer adjusters:
1) to adjust rebound damping (fig.30);
2) to adjust inner springs preload (fig. 30);
3) to adjust compression damping (fig. 31).
Make sure the vehicle is stable, on the side stand.
Use a flat screwdriver to turn adjuster (1), at the top of
every fork leg, and change rebound damping.
Use a flat screwdriver to turn adjuster (3), at the back of
wheel shaft pinch bolts, and change compression
damping.
Adjuster (1) has click settings, every click corresponds to a
different damping setting. Adjuster (3) is a screw so
damping variation is continuous. Completely tighten the
adjuster to reach "0" position, corresponding to max
damping. Starting from this position, turn counter
clockwise and count the clicks - which correspond to
position "1", "2", etc. - or measure the angular rotation of
the adjuster.
E
fig. 30
S
3
H
fig. 31
39
DUCum_1000DS####03_###e.book Page 40 Wednesday, March 12, 2003 4:33 PM
STANDARD factory setting is as follows:
compression: 1 turn;
rebound: 11 clicks.
To change the preload of the spring inside each fork leg
turn the hex. adjusting nut (2) with a 22-mm hexagon
wrench.
Height (A, fig. 31a) determines preload and may vary from
25 to 10 mm.
Factory setting is 20 mm.
2
2
Important
Adjust both fork legs to same settings.
E
A
fig. 31a
40
DUCum_1000DS####03_###e.book Page 41 Wednesday, March 12, 2003 4:33 PM
Rear shock absorber adjusters (fig. 32 and 32a)
The rear shock absorber features outer adjusters to set the
vehicle according to load conditions.
The rebound adjuster (1) is on the right-hand side at the
bottom shock absorber-to-swingarm fitting.
The compression adjuster (2) is on the shock absorber
expansion reservoir.
Turn adjusters (1 and 2) clockwise to increase damping,
counter clockwise to decrease it.
STANDARD setting for rebound adjuster (1):
From fully closed position (clockwise) turn out by 2 turns.
STANDARD setting for the compression adjuster (2):
completely open position (counter clockwise).
Knob (3), on the frame right-hand side, allows adjustment
of the shock absorber outer spring preload, follow
instructions on the knob itself.
STANDARD setting corresponds to knob minimum
position (LOW).
S
S
H
H
2
E
1
fig. 32
HIGH
Warning
The shock absorber is filled with gas under pressure
and may cause severe damage if taken apart by unskilled
persons.
LOW
3
fig. 32a
41
DUCum_1000DS####03_###e.book Page 42 Wednesday, March 12, 2003 4:33 PM
Rear-view mirrors adjustment
Adjustment is made by simply pushing the mirror in the
direction wanted (fig. 33).
To lock the mirror in position, tighten the screw at the
bottom of the support (fig. 33a).
E
fig. 33
fig. 33a
42
DUCum_1000DS####03_###e.book Page 43 Wednesday, March 12, 2003 4:33 PM
Motorcycle trim adjustment
Motorcycle trim is the result of many tests carried out by
our engineers in the most different conditions.
Changing this parameter is a very delicate operation that
might prove dangerous if improperly carried out.
Before changing standard setting, it is advisable to
measure the reference value (H, fig. 34).
fig. 34
The rider can change motorcycle trim according to his/her
own riding style by setting shock absorber position (fig.
34a).
Loosen nuts (3) on ball joints (1) and use socket (A) to
increase or decrease linkage (2) center distance.
Once set, tighten nuts (3) to 25 Nm.
H
Note
Be careful because lower nut (3) has a left thread.
Warning
Linkage (2) length, in-between joints (1) axes, must
not exceed 255 mm.
2
2
1
3
3
A
fig. 34a
43
E
DUCum_1000DS####03_###e.book Page 44 Wednesday, March 12, 2003 4:33 PM
DIRECTIONS FOR USE
Running-in recommendations
E
Max. rotation speed (fig. 35)
Rotation speed (rpm) for running-in period and during
standard use:
1) up to 1000 km;
2) from 1000 to 2500 km;
3) after 2500 km.
Up to 1000 km
During the first 1000 km, keep an eye on the revolution
meter. The indicator must not exceed:
5,500-6,000 rpm.
During the first hours of riding, it is advisable to run the
engine at varying load and rpm, though still within
recommended limit. To this end, roads with plenty of
bends and even hilly areas are ideal for a most efficient
running-in of engine, brakes and suspensions.
For the first 100 km, use the brakes gently. Do not brake
violently or keep brake applied for too long. This will enable
a correct break-in of friction material on brake pads against
brake discs.
44
For all mechanical moving parts to adapt to one another
and above all not to adversely affect the life of basic engine
parts, it is advisable to avoid harsh accelerations and not to
run the engine at high rpm for too long, especially uphill.
Furthermore, the drive chain should be inspected
frequently. Lubricate as required.
From 1000 to 2500 km
At this point, you can squeeze some more power out of
your engine, being careful, however, to never exceed
7,000 rpm.
Important
During the whole running-in period, the maintenance
and service rules recommended in this manual should be
observed carefully. Have the service inspections
performed as recommended in the Warranty Card.
Failure to comply with these rules will release Ducati
Motor Holding S.p.A. from any liability whatsoever for
resulting engine damage or shorter engine life.
DUCum_1000DS####03_###e.book Page 45 Wednesday, March 12, 2003 4:33 PM
After 2500 km
After running-in, never exceed the following values during
the motorcycle standard use:
10,000 rpm.
Strict observance of running-in recommendations will
ensure longer engine life and reduce the likelihood of
overhauls and tune-ups.
E
2.500 ÷ +Km
1.000 ÷ 2.500 Km
km/h
miles
mph
km/L
mpgal
0 ÷ 1.000 Km
fig. 35
45
DUCum_1000DS####03_###e.book Page 46 Wednesday, March 12, 2003 4:33 PM
Pre-ride checks
Warning
Failure to carry out these checks before riding, may
lead to motorcycle damage and injury to rider and
passenger.
E
Before riding, perform a thorough check-up on your bike as
follows:
Fuel level in the tank
Check fuel level in the tank.
Fill tank if needed (page 51).
Engine oil level
Check oil level in the sump through the sight glass. Top up
if needed (page 77).
Brake and clutch fluid
Check fluid level in the relevant reservoirs (page 58).
Tyre condition
Check tyre pressure and condition (page 75).
Controls
Work the brake, clutch, throttle and gear change controls
(levers, pedals and twistgrips) and check for proper
operation.
Lights and indicators
Make sure lights, indicators and horn work properly.
Replace any burnt-out bulbs (page 66).
Key-operated locks
Check that fuel filler plug (page 35) and pillion seat catch
locks (page 36) are closed firmly.
46
Stand
Make sure side stand operates smoothly and is in the
correct position (page 38).
Warning
In case of malfunctioning, do not start the motorcycle
and call a DUCATI Dealer or Authorised Workshop.
DUCum_1000DS####03_###e.book Page 47 Wednesday, March 12, 2003 4:33 PM
Starting the engine
Warning
Before starting the engine, become familiar with the
controls you will need to use when riding (see page 10).
1) Move ignition switch to ON (fig. 36). Check that the
green pilot light N (8, fig. 5) and the red one
(7,
fig. 5), on the instrument panel are on.
O
ON
E
PUSH
FF
K
C
LO
Important
The oil pressure light should go out a few seconds
after the engine has started (page 13).
ON
N
IO
P
NIT
IG
Note
It is possible to start the engine with side stand down
and the gearbox in neutral. When starting the bike with a
gear engaged, pull the clutch lever (in this case the side
stand must be up).
fig. 36
47
DUCum_1000DS####03_###e.book Page 48 Wednesday, March 12, 2003 4:33 PM
2) Check that the stop switch (1, fig. 37) is positioned to
(RUN), then press the starter button (2).
E
This model is equipped with a servoignition system.
To achieve assisted engine starting, press the button (2)
and release it immediately.
Pressing the button (2) operates automatic engine starting
for a maximum period of time that varies depending on
engine temperature.
When the engine has started, the system prevents the
starter motor from turning over.
If the engine fails to start, allow at least 2 seconds before
pressing the starter button (2) again.
Let the engine start without using the throttle control.
1
2
fig. 37
Note
If the battery is flat, the system will automatically
prevent the starter motor from turning over.
Important
Do not rev up the engine when it is cold. Allow some
time for oil to reach all points that need lubricating.
48
DUCum_1000DS####03_###e.book Page 49 Wednesday, March 12, 2003 4:33 PM
Moving off
1) Disengage the clutch squeezing the control lever.
2) Push down on gear change lever sharply with the tip
of your foot to engage the first gear.
3) Speed up engine, by turning the throttle twistgrip and
slightly releasing the clutch lever at the same time.
The motorcycle will start moving off.
4) Let go of clutch lever and speed up.
5) To shift up, close the throttle to slow down engine,
disengage the clutch, lift the gear change lever and let
go of clutch lever.
To shift down, release the twistgrip, pull the clutch
control lever, shortly speed up to help gears
synchronise, shift down and release the clutch.
The controls should be used correctly and timely:
when riding uphill do not hesitate to shift down as
soon as the motorcycle tends to slow down, so you
will avoid stressing the engine and the motorcycle
abnormally.
Important
Avoid harsh accelerations, as this may lead to
misfiring and transmission snatching. The clutch lever
should not be pulled longer than necessary after gear is
engaged, or friction parts may overheat and wear out.
Braking
Slow down in time, shift down to engine-brake first and
then brake applying both brakes. Pull the clutch lever
before stopping the motorcycle, to avoid sudden engine
stop.
Warning
Use both brake lever and pedal for effective braking.
Using only one of the brakes will give you less braking
power.
Never use brake controls harshly or violently or you may
lock the wheels and lose control of the motorcycle.
When riding in the rain or on slippery surfaces, braking will
become less effective. Always use the brakes very gently
and carefully when riding under these conditions. Any
sudden manoeuvres may lead to loss of control.
When tackling long, high-gradient downhill road tracts,
shift down gears to use engine braking. Apply one brake at
a time and use brakes sparingly. Keeping the brakes
applied all the time would cause the friction material to
overheat and dangerously reduce braking power.
Underinflated or overinflated tyres reduce braking
efficiency, steering accuracy and road holding in a bend.
49
E
DUCum_1000DS####03_###e.book Page 50 Wednesday, March 12, 2003 4:33 PM
Stopping the motorcycle
If you let go of the throttle twistgrip, the motorcycle will
slow down gradually and smoothly. Then, shift down
releasing the clutch, and finally change from first to
neutral. Apply brakes and you will bring the motorcycle to
a complete stop.
To switch the engine off, simply turn the key to OFF (page
26).
E
Important
The motorcycle is fitted with an energy-saving
control unit. In order to prevent any current absorption, the
control unit is disabled in case the key is left on ON by
accident and the starter button is not pressed after 15
seconds; turn the key to OFF and back to ON to reset.
However, avoid leaving the key set to ON with the engine
stopped.
Parking
Stop the motorcycle, then put it on the side stand (see
page 38).
Turn the handlebar fully left and block it by pushing in the
ignition key and turning it to the LOCK position.
If you park in a garage or other facilities, make sure that
there is proper ventilation and that the motorcycle is not
near a source of heat or sparks. You may leave the parking
lights on by turning the key to position P.
50
Important
Do not leave the key turned to P for long periods or
the battery will run down.
Never leave the ignition key in the switch when you are
leaving your bike unattended.
Warning
The exhaust system might be hot, even after engine
is switched off; pay particular attention not to touch
exhaust system with any body part and do not park the
vehicle next to inflammable material (wood, leaves etc.).
Warning
Using padlocks or locks that prevent motion (such as
brake disc or crown sprocket locks and so on) is very
dangerous and may affect motorcycle operation as well as
the safety of rider and passenger.
DUCum_1000DS####03_###e.book Page 51 Wednesday, March 12, 2003 4:33 PM
Refuelling (fig. 38)
Never overfill the tank when refuelling. Fuel should never
be touching the rim of filler recess.
Max level
Warning
Use low-lead fuel having at least 95 fuel octane rating
(see table "Refuelling" page 81). Be sure there is no fuel
trapped in the filler recess.
E
fig. 38
51
DUCum_1000DS####03_###e.book Page 52 Wednesday, March 12, 2003 4:33 PM
Tool kit and accessories (fig. 39)
In the right-hand fairing there is a compartment that can be
accessed after opening the door (see page 37), in this
compartment there are:
an Owner's manual;
a helmet fastening cable;
The tool bag (fig. 40) holds:
- box wrench for spark plugs;
- tommy bar;
- double-bit screwdriver.
E
fig. 39
fig. 40
52
DUCum_1000DS####03_###e.book Page 53 Wednesday, March 12, 2003 4:33 PM
MAIN MAINTENANCE OPERATIONS
Removing the fairing
Some servicing operations need the motorcycle fairing to
be removed.
E
Warning
Firmly secure all removed parts properly when
refitting them, otherwise some of them might suddenly
come off when riding and you may loose control of your
motorcycle.
Important
At reassembly always fit nylon washers when
tightening fastening screws to avoid damage to painted
parts and Plexiglas headlamp fairing.
53
DUCum_1000DS####03_###e.book Page 54 Wednesday, March 12, 2003 4:33 PM
Mobile headlight fairing
Loosen the four screws (1) that secure the mobile
headlight fairing to the supports with seal (2).
Remove the mobile headlight fairing together with
windshield ( fig. 41).
To change the windshield, with the suitable torx wrench
loosen the screws (3) with nylon washer (4), lock rubbercoated nuts (5) from the inside (fig. 41a).
E
2
While fitting the new windshield, tighten the screws (2)
starting from the center one.
Check that the seals (2) are on the supports then position
the mobile headlight fairing and secure it on either sides
with screws (1).
Tighten screws (1).
1
fig. 41
5
4
3
fig. 41a
54
DUCum_1000DS####03_###e.book Page 55 Wednesday, March 12, 2003 4:33 PM
Fixed headlight fairing
Undo the six screws (1) securing the inner flange, on either
side of the headlight fairing, then pull the inner flange
upward and remove it (fig. 42).
1
Note
Be careful while removing the flange not to damage
the paint of the headlight fairing.
Undo the six screws (2) securing the fixed headlight fairing
to the headlight support (fig. 42a).
Remove the fixed headlight fairing.
E
When reassembling, tighten the four centre screws first
then the two on the sides.
Position the inner flange on the fixed headlight fairing,
make sure that the holes match.
Tighten the six screws (1), do not overtighten or the
inserts on the fixed headlight fairing might damage.
fig. 42
2
2
fig. 42a
55
DUCum_1000DS####03_###e.book Page 56 Wednesday, March 12, 2003 4:33 PM
Left side fairing
Working on the left side, from inside the fairing, turn
counter clockwise by ¼ of a turn the quick-release fitting
(1) to release the left side fairing front end (fig. 43).
Slide out tab (2) at the frame support to release the left
side fairing rear end: it will be easier if you push from the
outside on the fairing at the tab (fig. 44).
Slide the left side fairing out of the fuel tank retaining pins
and remove it.
E
1
fig. 43
PUSH
2
fig. 44
56
DUCum_1000DS####03_###e.book Page 57 Wednesday, March 12, 2003 4:33 PM
Before reassembling, make sure that rubber elements (3)
and seal (4) are correctly in place on pin (5) on the inside of
the fairing (fig. 45).
Fit the left side fairing, start from the rear end and fit
rubber elements in fuel tank pins (fig. 45a).
Push the fairing at pin (5) to be able to engage tab (2) to the
pin end.
Push front quick-release fitting (1) and turn it clockwise by
¼ of a turn to engage it.
4
3
5
E
fig. 45
fig. 45a
57
DUCum_1000DS####03_###e.book Page 58 Wednesday, March 12, 2003 4:33 PM
Checking brake and clutch fluid level
Fluid level should never fall below the MIN mark on each
reservoir (fig. 46 and 46a).
If level drops below the limit, air might get into the circuit
and affect the operation of the system involved.
Brake and clutch fluid must be topped up and changed at
the intervals specified in the routine maintenance chart on
the Warranty Card by a Ducati Dealer or Authorised
Workshop.
E
Important
It is recommended all brake and clutch lines be
changed every four years.
Brake system
If you find exceeding play on brake lever or pedal and brake
pads are still in good condition, contact your Ducati Dealer
or Authorised Workshop to have the system inspected
and any air drained out of the circuit.
Warning
Brake and clutch fluid and will damage paintwork and
plastic parts if accidentally spilled.
Hydraulic oil is corrosive; it may cause damage and lead to
severe injuries.
Never mix different quality oils.
Check seals for proper sealing.
58
fig. 46
DUCum_1000DS####03_###e.book Page 59 Wednesday, March 12, 2003 4:33 PM
Clutch system (fig. 46a)
If the control lever has exceeding play and the
transmission snatches or jams as you try to engage a gear,
it is possible that there is air in the circuit. Contact your
Ducati Dealer or Authorised Workshop to have the system
inspected and air drained out.
(MAX) 33 mm
mm
MIN
Warning
Clutch fluid level will increase as clutch plate friction
material wears down. Do not exceed specified level (3 mm
above minimum level).
E
fig. 46a
59
DUCum_1000DS####03_###e.book Page 60 Wednesday, March 12, 2003 4:33 PM
Checking brake pads for wear (fig. 47)
MIN
To facilitate inspection without removing the pads from
the calipers, front brake pads have a wear mark. If the
grooves in the friction material are still visible, the pad is
still in good condition.
Rear brake pads are to be replaced when friction material
is worn down to about 1 mm (fig. 47a). This can be seen
through the opening in the caliper halves.
E
Important
Have the brake pads replaced at a Ducati Dealer or
Authorised Workshop.
fig. 47
1 mm
fig. 47a
60
DUCum_1000DS####03_###e.book Page 61 Wednesday, March 12, 2003 4:33 PM
Lubricating joints
The condition of the outer sheaths of the throttle cables
should be checked at regular intervals. The sheaths should
show no signs of squeezing or cracking. Work the controls
to make sure the cable slides smoothly inside the sheath:
if you feel any friction or hard spots, have the cable
replaced by your Ducati Dealer or Authorised Workshop.
To prevent these failures it is best to remove the cover by
unscrewing the two fastening screws (1, fig. 48) and then
grease the cable end and the pulley with SHELL Advance
Grease or Retinax LX2.
Warning
When refitting the cover, be sure to slide the cable
properly onto the suitable pulley.
1
E
fig. 48
Refit the cover and tighten the screws (1).
To ensure smooth operation of side stand joint, clean off
any dirt and apply SHELL Alvania R3 at all points exposed
to friction (1, fig. 48a).
fig. 48a
61
DUCum_1000DS####03_###e.book Page 62 Wednesday, March 12, 2003 4:33 PM
Throttle cable free play adjustment
The throttle twistgrip must have a free play of 1.5 - 2.0 mm
(fig. 49) measured at the edge of the twistgrip, at all
positions of the handlebars.
If not so, it is necessary to adjust control travel through the
relevant adjusters (1) of the throttle body (fig. 50).
1,5 2 mm
1,5 ÷ 2 mm
Important
To adjust the free play of the throttle control, call an
Authorised Dealer or Service Center.
E
fig. 49
1
fig. 50
62
DUCum_1000DS####03_###e.book Page 63 Wednesday, March 12, 2003 4:33 PM
Charging the battery (fig. 51)
Before charging the battery, it is best to remove it from the
motorcycle.
Remove the LH half-fairing (see page 56).
Always disconnect the black negative terminal (-) first, and
then the red positive terminal (+).
Undo the two screws (1) on battery brackets and remove
the battery.
Warning
Batteries develop explosive gases: keep battery
away from heat sources and flames.
+
-
1
E
Charge the battery in a well ventilated room.
Connect battery charger red lead to battery positive
terminal (+), the black lead to battery negative terminal (-).
Important
Always make sure the charger is off when you
connect the battery to it, or you might get sparks at the
battery terminals that could ignite the gases inside the
cells. Always connect the red positive terminal (+) first.
fig. 51
Warning
Keep the battery out of the reach of children.
Charge the battery at 0.9 A for 5-10 hours.
Refit battery to its mount and secure brackets with screws
(1), then connect the terminals, grease the fastening
screws to improve conductivity.
63
DUCum_1000DS####03_###e.book Page 64 Wednesday, March 12, 2003 4:33 PM
Checking the drive chain tension (fig. 52)
Move the motorcycle until finding the position where the
chain is tightest.
Lower the side stand and rest the bike on it. At the most
forward position of the side chain guard check the distance
between swingarm and chain lower section links middle
axis. The value must be between 38 and 42 mm as
indicated on the label on the swingarm. If it is not so, it is
necessary to change the chain tension.
E
Important
Contact an Ducati Dealer or Authorised Workshop to
have the drive chain tensioned.
38 ÷ 42 mm
fig. 52
Warning
Proper tightening of screws (1, fig. 52a) on swingarm
is fundamental for the rider and passenger safety.
Important
A chain which is not properly tensioned might cause
early wear of any transmission parts.
1
fig. 52a
64
DUCum_1000DS####03_###e.book Page 65 Wednesday, March 12, 2003 4:33 PM
Chain lubrication
The chain fitted on your motorcycle has O-rings that keep
dirt out of and lubricant inside the sliding parts. The seals
might be irreparably damaged if the chain is cleaned using
any solvent other than those specific for O-ring chains or
washed using steam or water jets. After cleaning, blow
the chain dry or dry it using absorbent material and apply
SHELL Advance Chain or Advance Teflon Chain on each
link.
Important
Using non-specific lubricants may lead to severe
damage to chain, front and rear sprocket.
E
65
DUCum_1000DS####03_###e.book Page 66 Wednesday, March 12, 2003 4:33 PM
Replacing headlamp bulbs
Before replacing a burnt-out bulb, make sure that the new
bulb complies with voltage and wattage as specified on
page 88, "Electric System", for that lighting device. Always
test the new lamp before refitting the parts you have
removed.
LO
Fig. 53 shows the position of low beam (LO), high beam
(HI) and parking (1) bulbs in the headlight.
E
Working on the sides of the fixed headlight fairing, in the
area under the instrument panel (fig. 54), release upper
and lower clips (2) and open cover (3) to gain access to the
headlight bulbs.
HI
1
fig. 53
Note
For easier reference, the headlight shown is removed
from the vehicle.
2
3
3
2
2
3
fig. 54
66
DUCum_1000DS####03_###e.book Page 67 Wednesday, March 12, 2003 4:33 PM
Low beam (upper)
Disconnect connectors (4) from the clamps on the bulb.
Release clip (5) from bulb socket by pushing down and
then squeezing its ends (fig. 55).
Pull the clip up (5).
Remove the burnt-out bulb (6) and replace it with a new
one, do not touch the transparent body of the bulb (fig. 56).
5
4
Note
Be careful to hold the new bulb at the base only.
Never touch the transparent body with your fingers or it
will blacken resulting in reduced bulb brilliancy.
E
fig. 55
6
fig. 56
67
DUCum_1000DS####03_###e.book Page 68 Wednesday, March 12, 2003 4:33 PM
Note for the USA version:
To remove the low beam bulb (7) disconnect
connector (A) from the wiring then turn the bulb counter
clockwise and extract the burnt-out bulb (fig. 57). Replace
it with a new one with the same rating. When refitting,
turn the bulb clockwise to lock it on the bulb body.
7
LOCK
OPEN
E
A
fig. 57
USA
High beam (lower)
Disconnect connector (8) from the terminals on high beam
bulb (fig. 58)
Disconnect the clip (9) from the bulb socket by pushing
down and then squeezing the ends.
Pull the clip up (9).
9
8
fig. 58
68
DUCum_1000DS####03_###e.book Page 69 Wednesday, March 12, 2003 4:33 PM
Remove the burnt-out bulb (10) and replace it with a new
one, do not touch the transparent quartz (fig. 59).
Parking light
Disconnect the connections (11) from terminals (fig. 60).
Remove the parking light (12) from its seat and replace it
with a new one with the same rating.
10
Refitting the bulbs
Once you have replaced all necessary parts, reconnect
cable connectors on bulb terminals, previously
disconnected. Reposition headlight cover in its seat, make
sure that the edges match and secure it to headlight body
by tightening the clips.
E
fig. 59
Note
It is possible to reverse the cables on bulb terminals.
12
11
fig. 60
69
DUCum_1000DS####03_###e.book Page 70 Wednesday, March 12, 2003 4:33 PM
Changing the front direction indicators bulbs
Front direction indicators are integrated in the rear-view
mirrors.
To change the bulb, undo the screw (1) and remove the
indicator lens (2) from mirror body (fig. 61).
E
Bulb (3) has a bayonet-type fitting, push it and turn counter
clockwise to remove it. Change the burnt-out bulb with a
new one with same rating, fit it, push it and turn clockwise
until it clicks in place (fig. 62).
Refit the lens (2) in the slot on indicator body, make sure
that the edges match.
Secure the lens with screw (1).
2
1
fig. 61
3
fig. 62
70
DUCum_1000DS####03_###e.book Page 71 Wednesday, March 12, 2003 4:33 PM
Changing the rear direction indicators bulbs
To change rear direction indicator bulbs it is necessary to
turn the indicator body (1) by one quarter of a turn, setting
it with the lens up, and then remove it from tail light
support (fig. 63).
The bulb (2, fig. 63a) has a bayonet-type fitting: press and
rotate anti-clockwise to remove; fit the spare bulb by
pressing and turning clockwise until it clicks.
Refit indicator body (1) and secure it to tail light support by
turning it by one quarter of a turn.
1
1
E
fig. 63
1
2
fig. 63a
71
DUCum_1000DS####03_###e.book Page 72 Wednesday, March 12, 2003 4:33 PM
Changing the number plate and stop light bulbs
Loosen the two screws (1) securing tail light support to
number plate holder, on the inboard side.
Loosen screw (2) and slightly slide out tail light support
(fig. 64).
Disconnect connector (A) of the rear wiring and remove tail
light support (fig. 65).
2
E
1
fig. 64
A
fig. 65
72
DUCum_1000DS####03_###e.book Page 73 Wednesday, March 12, 2003 4:33 PM
Loosen the two self-tapping screws (3) securing body (4)
with transparent cover for number plate light.
Slide out the body and transparent cover and change bulb
(5) for number plate light (fig. 66).
3
4
5
To change stop light bulb it is necessary to carry out the
procedure described and remove transparent element (6)
for stop light from the support.
Remove bulb (7) by pushing it and turning counter
clockwise, replace it (fig. 67).
While refitting transparent cover (6), properly fit tabs (B) in
the slots on the support.
E
4
fig. 66
B
6
7
fig. 67
73
DUCum_1000DS####03_###e.book Page 74 Wednesday, March 12, 2003 4:33 PM
E
Beam setting (fig. 68)
When checking beam setting, put the motorcycle upright.
Tyres should be inflated at the correct pressure and one
person should be sitting astride the motorcycle, keeping it
at right angles to its longitudinal axis. Place the motorcycle
opposite a wall or a screen, 10 meters apart from it, then
draw a horizontal line dictated by headlamp centre and a
vertical one in line with the longitudinal axis of motorcycle.
If possible, perform this check in dim light.
Switch on the low beam. The height of the light spot
(measured at the upper limit between dark and lighted-up
area) should not exceed 9/10th of the height from ground
of headlamp centre.
Note
The procedure described here is in compliance with
the "Italian Standard" establishing the maximum height of
the light beam. Owners in other countries will adapt said
procedure to the provisions in force in their countries.
9 x
10
x
10 m
fig. 68
A
B
Beam vertical adjustment (fig. 69)
This adjustment can be made with buttons (A) and (B) on
the instrument panel, enter "Beam vertical setting" mode
(see pag 19).
km/h
miles
mph
km/L
mpgal
fig. 69
74
DUCum_1000DS####03_###e.book Page 75 Wednesday, March 12, 2003 4:33 PM
Tubeless tyre pressure
Front tyre:
220 Kpa (2.2 bar - 32.3 psi)
Rear tyre:
240 Kpa (2.4 bar - 35.2 psi)
As tyre pressure is affected by temperature and altitude
variations, you are advised to check and adjust it whenever
you are riding in areas where ample variations in
temperature or altitude occur.
Important
Check and set tyre pressure when tyres are cold.
To avoid front wheel rim distortion, when riding on bumpy
roads, increase front tyre pressure by 0.2 - 0.3 bar.
Tyre repair or replacement (Tubeless)
In the event of a tiny puncture, tubeless tyres will take a
long time to deflate, as they tend to keep air inside. If you
find low pressure on one tyre, check the tyre for
punctures.
Warning
A tyre must be replaced when punctured.
Only fit tyres of the same type as original-equipment tyres.
Be sure to tighten the valve caps securely to avoid leaks
when riding. Never use tube type tyres. Failure to heed
this warning may lead to sudden tyre bursting and to
serious danger to rider and passenger.
After replacing a tyre, the wheel must be balanced.
Important
Do not remove or shift the wheel balancing weights.
Note
If tyres need replacing, contact a Ducati Dealer or
Authorised Workshop to make sure wheels are removed
and refitted correctly.
75
E
DUCum_1000DS####03_###e.book Page 76 Wednesday, March 12, 2003 4:33 PM
Minimum tread depth
Measure tread depth (S, fig. 70) at the point where tread
is most worn. It should not be less than 2 mm and anyway
not below the legal limit.
E
S
Important
Visually inspect the tyres at regular intervals for
cracks and cuts, especially on the side walls, bulges or
large spots that are indicative of internal damage. Replace
them if badly damaged.
Remove any stones or other foreign bodies caught in the
tread.
fig. 70
76
DUCum_1000DS####03_###e.book Page 77 Wednesday, March 12, 2003 4:33 PM
Checking engine oil level (fig. 71)
Engine oil level can be checked through the sight glass (1)
provided on the clutch cover on the engine right side.
When checking oil level, the motorcycle should be upright
and the engine cold.
Oil level should be between the marks near the sight
glass.
Top up oil level with SHELL Advance Ultra 4, if low.
Undo the filler plug (2) and top up to correct level.
Refit the plug.
2
1
E
Important
Engine oil and oil filters must be changed by a Ducati
dealer or authorized workshop at regular intervals, as
specified in the routine maintenance chart (see Warranty
Card).
10W
Multigrade Unigrade
Viscosity
SAE 10W-40
The other viscosity degrees indicated in the table can be
used if the local average temperature is within the limits
specified for that oil viscosity (fig. 72).
fig. 71
20W
20
30
40
20W–40 20W–50
15W–40 15W–50
10W–40
10W–30
–10
0
10
20
30
40 C
fig. 72
77
DUCum_1000DS####03_###e.book Page 78 Wednesday, March 12, 2003 4:33 PM
E
Cleaning and replacing the spark plugs (fig. 73)
Spark plugs are essential to smooth engine running and
should be checked at regular intervals. This provides a
good measure of engine condition.
Contact an Ducati Dealer or Authorised Workshop to have
the spark plug checked and changed, if needed. Their staff
shall check the color of the ceramic insulator on the central
electrode: a light brown, even colour is a sign of good
engine condition.
Check wear on the central electrode and the gap: it should
be 0.6-0.7 mm.
Important
If gap is too wide or too close, engine performance
will be affected. This could also cause misfiring or irregular
idling.
78
0,6÷0,7 mm
fig. 73
DUCum_1000DS####03_###e.book Page 79 Wednesday, March 12, 2003 4:33 PM
Cleaning the motorcycle
To preserve the finish of metal parts and paintwork, wash
and clean your motorcycle at regular intervals, anyway
according to the road conditions you ride in.
Use specific products only. Prefer biodegradable products.
Avoid aggressive detergents or solvents.
Important
Do not wash your motorcycle right after use. When
the motorcycle is still hot, water drops will evaporate
faster and spot hot surfaces.
Never clean the motorcycle using hot or high-pressure
water jets. Cleaning the motorcycle with water cleaners
may lead to seizure or severe failure of front fork, wheel
hub assembly, electric system, fork seals, air inlets or
exhaust silencers and adversely affect the operation of
motorcycle safety features.
If needed, clean off stubborn dirt or exceeding grease from
engine parts using a degreasing agent. Be sure to avoid
contact with drive parts (chain, sprockets, etc.).
Rinse with warm water and dry all surfaces with chamois
leather.
Warning
Loss of braking may occur immediately after washing
the motorcycle.
Never grease or lubricate the brake discs. Loss of braking
and further accidents may occur. Clean the discs with an
oil-free solvent.
Storing the bike away
If the motorcycle is to be left unridden over long periods,
it is advisable to carry out the following operations before
storing it away:
clean the motorcycle;
drain all fuel from tank;
pour a few drops of engine oil into the cylinders through
the spark plug seats, then crank the engine by hand a few
times so a protective film of oil will spread on cylinder
inner walls;
place the motorcycle on a service stand;
disconnect and remove the battery. Battery should be
checked, charged or replaced whenever the motorcycle
has been left unridden for over a month;
protect the motorcycle with a suitable canvas available
from Ducati Performance. This will protect paintwork and
let condensate breathe out.
Important notes
Some countries, such as France, Germany, Great Britain,
Switzerland, etc. have compulsory emission and noise
standards that include mandatory inspections at regular
intervals.
It is the Owner's responsibility to have any parts not in
compliance with the standards in force in his/her country
replaced with spare parts complying with local law.
79
E
DUCum_1000DS####03_###e.book Page 80 Wednesday, March 12, 2003 4:33 PM
TECHNICAL DATA
Weights
Dry weight:
200 Kg
Carrying full load:
410 Kg
Overall dimensions (mm) (fig. 74)
Warning
Failure to observe weight limits could result in poor
handling and impair the performance of your motorcycle,
and you may lose control of the motorcycle.
E
169
820
1280
830
1462
2130
80
fig. 74
DUCum_1000DS####03_###e.book Page 81 Wednesday, March 12, 2003 4:33 PM
Top-ups
Type of fluid
cu dm (litres)
Fuel tank, including a reserve of 6.5 cu dm (liters)
Unleaded fuel 95 fuel octane rating (at least)
20
Lubrication circuit
SHELL Advance Ultra 4
3.9
Front/Rear brake and clutch circuits
Special fluid for hydraulic systems
SHELL-Advance Brake DOT 4
_
Protectant for electric contacts
Spray for electric systems
SHELL-Advance Contact Cleaner
_
Front fork
SHELL-Advance Fork 7.5 or Donax TA
(each leg) 600
cu. cm.
E
Importante
Do not use any additives in fuel or lubricants.
81
DUCum_1000DS####03_###e.book Page 82 Wednesday, March 12, 2003 4:33 PM
Engine
Twin-cylinder 4-stroke "L" 1000cc engine with
Desmodromic system, with electronic fuel injection, aircooled.
E
Bore:
94 mm.
Stroke:
71.5 mm.
Total displacement:
992 c. c.
Compression ratio:
10.5 ± 0.5:1
Max. power at crankshaft (95/1/EC), kW/HP:
62 Kw (84 HP) at 8000 rpm
Max. torque at the crankshaft (95/1/EC):
84 Nm - 8.5 Kg at 5000 rpm
Max. rpm:
8700 rpm
Desmodromic timing system (fig. 75)
1)
2)
3)
4)
5)
6)
7)
8)
Opening (or upper) rocker arm.
Opening rocker arm shim.
Split rings.
Closing (or lower) rocker arm shim.
Return spring for lower rocker arm.
Closing (or lower) rocker arm.
Camshaft.
Valve.
1
Importante
Do not exceed specified rotation speed limits under
any running condition.
Timing system
Desmodromic (type) with two valves per cylinder,
operated by four rockers (2 opening rockers and 2 closing
rockers) and an overhead camshaft. It is operated by the
crankshaft through spur gears, belt rollers and toothed
belts.
82
5
2
7
8
3
4
6
fig. 75
DUCum_1000DS####03_###e.book Page 83 Wednesday, March 12, 2003 4:33 PM
Performance data
Maximum speed in any gear should be reached only after
a correct running-in period with the motorcycle properly
serviced at the recommended intervals.
Max. speed (rider alone):
208 Kph.
Spark plugs
Ignition in every cylinder is performed with two spark
plugs. This solution offers smoother combustion and more
power, mainly at mid-range.
Make:
Champion
Type:
RA6 HC
Exhaust system
Catalysed, according to Euro 2 environmental protection
standards.
Note
On the USA (US) version there is no catalytic
converter.
83
E
DUCum_1000DS####03_###e.book Page 84 Wednesday, March 12, 2003 4:33 PM
E
Transmission
Clutch housing and plates are made of a special aluminum
alloy.
Dry clutch controlled by a lever on the handlebar LH side.
Drive is transmitted from engine to gearbox main shaft via
spur gears.
Engine sprocket/clutch sprocket ratio:
32/59 .
Gearbox:
6-speed with constant mesh gears, gear change pedal on
left side of motorcycle.
Gear sprocket/rear sprocket ratio:
15/42.
Total gear ratios:
1st gear 15/37
2nd gear 17/30
3rd gear 20/27
4th gear 22/24
5th gear 24/23
6th gear 28/24
Drive chain from gearbox to rear wheel:
Make:
DID
Type:
525 HV.
Size:
5/8"x5/16"
Importante
The above gear ratios are part of the homologated
specifications and under no circumstances must they be
modified.
If you wish to tune up your motorcycle for competitive
trials, you may refer to Ducati Motor Holding S.p.A. who
will be glad to provide information about the special ratios
available. Relevant instructions and original spare parts are
available from your local Dealer or authorised workshop.
Warning
If the rear sprocket needs replacing, contact a Ducati
Dealer or an authorised workshop. If improperly replaced,
this component could seriously endanger your safety and
that or your passenger, and cause irreparable damage to
your motorcycle.
84
DUCum_1000DS####03_###e.book Page 85 Wednesday, March 12, 2003 4:33 PM
Brakes
Front brake
Double drilled disc, half-floating
Material:
steel.
Disc diameter:
320 mm
Hydraulically operated by a control lever on right
handlebar.
Braking surface:
88 sq cm.
Brake calipers make:
BREMBO
Type:
30/34-4 pistons
Friction material:
FERIT I/D 450 FP.
Master cylinder type:
PSC 16 with built-in reservoir
Rear brake
With steel drilled disc in stainless steel.
Disc diameter:
245 mm.
Hydraulically operated by a pedal on RH side.
Braking surface:
32 sq cm.
Make:
BREMBO
Type:
34-2 pistons.
Friction material:
FERIT I/D 450 FF
Master cylinder type:
PS 11B.
E
Warning
Brake fluid can dissolve paintwork and cause severe
eye and skin injuries in the event of accidental spilling.
Wash the affected area with abundant running water.
85
DUCum_1000DS####03_###e.book Page 86 Wednesday, March 12, 2003 4:33 PM
Frame
High-strength tubular treillis frame.
Steering angle (on each side):
35°
Steering geometry:
Headstock angle
24°
Trail:
109 mm.
E
Wheels
Front wheel
Six-spoke light alloy front wheel rim.
Dimensions:
3.50x17"
Rear wheel
Five-spoke light alloy rear wheel rim.
Dimensions:
5.50x17".
Front wheel shaft can be removed, whereas the rear
wheel is mounted to the hub of the single-sided swingarm.
86
Tyres
Front tyre
Tubeless, radial tyre.
Size:
120/70-ZR17.
Rear tyre
Tubeless, radial tyre.
Size:
180/55-ZR17.
DUCum_1000DS####03_###e.book Page 87 Wednesday, March 12, 2003 4:33 PM
Suspensions
Front
Hydraulic upside-down fork featuring outer adjusters for
rebound and compression damping and for the preload of
the springs inside fork legs.
Stanchion diameter:
43 mm.
Travel along leg axis:
165 mm.
Available in the following colors:
Ducati anniversary red;
frame: red, black;
rims: metal blue gray.
Ducati two-color gray:
frame: red, black;
rims: metal blue gray.
E
Rear
With progressive operation obtained by a rocker arm fitted
in-between frame and shock absorber top pivot point.
The rear shock absorber enables the adjustment of
rebound and compression damping and spring preload. At
the bottom pivot point it is connected to the single-sided
swinging arm made from aluminum alloy. The swinging
arm hinges on a pivot pin passing through the frame and
the engine. The whole system gives the bike excellent
stability.
Travel:
145 mm
87
DUCum_1000DS####03_###e.book Page 88 Wednesday, March 12, 2003 4:33 PM
E
Electric system
Basic electric items are:
Twin, stacked halogen headlight made of:
Low beam unit - HB3 12V-60W;
high beam unit - HB3 12V-60W;
parking light unit - 12V-5W.
Electrical controls on handlebar.
Turn indicators, 12V-10W bulbs.
Horn.
Stop light switches.
Tight-type battery 12V-10 Ah.
Generator 12V-520W.
Electronic voltage regulator (rectifier), protected by a 40
A fuse located on the side of the battery.
Starter motor, 12V-0.7 kW.
Tail light, 12V-5/21W double-filament bulb for stop light
and parking light; 12V-5W bulb for number plate light.
Note
See "Replacing bulbs" on page 66 for relevant
instructions.
88
DUCum_1000DS####03_###e.book Page 89 Wednesday, March 12, 2003 4:33 PM
Fuses
The main fuse carrier (1, fig. 76) is under left side fairing
(see page 56). The fuses can be accessed by removing the
safety gaiter.
Other than the main fuse carrier, there are other fuses that
are positioned at the sides of the battery.
1
Two fuses (2, fig. 77) on the right-hand side of the battery
protect the injection system and the ECU relay.
Fuse (3) protects the electronic regulator while fuse (4)
protects the system of the side stand sensor.
E
fig. 76
3
2
4
fig. 77
89
DUCum_1000DS####03_###e.book Page 90 Wednesday, March 12, 2003 4:33 PM
Remove the fuse cap (A, fig. 78) to expose the fuse.
A blown fuse is identified by the interrupted inner filament
(5, fig. 79).
A
2
Importante
Switch the ignition key to OFF before replacing a
fuse to avoid possible short circuits.
E
Warning
Never use a fuse with a rating other than specified.
Failure to observe this rule may damage the electric
system or even lead to fire.
fig. 78
5
IN GOOD CONDITION
INTEGRO
5
BLOWN
QUEMADO
fig. 79
90
DUCum_1000DS####03_###e.book Page 91 Wednesday, March 12, 2003 4:33 PM
Legend of the wiring diagram of electric system/
ignition
1) RH switch
2) Key-operated switch
3) Fuse box
4) Fuses
5) Starter motor
6) Starter contactor
7) Battery
8) Regulator fuse
9) Regulator
10)Generator
11)Rear RH turn indicator
12)Tail light
13)Rear LH turn indicator
14)Number plate light
15)Fuel tank
16)Horizontal cyl. spark plug
17)Vertical cyl. spark plug
18)Injection relay
19)Self-diagnosis connection
20)Vertical cyl. coil
21)Horizontal cyl. coil
22)Horizontal cyl. spark plug
23)Vertical cyl. spark plug
24)Horizontal cyl. injector
25)Vertical cyl. injector
26)TPS
27)Rpm/timing sensor
28)Oil temperature sensor - ECU
29)Speed sensor
30)Side stand switch
31)Neutral switch
32)Oil pressure switch
33)Rear stop switch
34)Stepper motor
35)Ignition/injection unit
36)Clutch switch
37)Front stop switch
38)Oil temp. sens.-instrument panel
39)LH switch
40)Immobilizer antenna
41)Air temperature sensor
42)Instrument panel
43)Light relay
44)Front LH turn indicator
45)Headlight
46)Front RH turn indicator
47)Horn
48)Grip wiring disc.
49)Disc.connection
E
91
DUCum_1000DS####03_###e.book Page 92 Wednesday, March 12, 2003 4:33 PM
E
Wiring Colour Coding
B Blue
W White
V Violet
Bk Black
Y Yellow
R Red
Lb Light Blue
Gr Gray
G Green
Bn Brown
O Orange
P Pink
Legend of fuse box
Pos.
El.items
Rat.
A
Key-on
7.5A
B
Lights
15A
C
Horn,stop,solenoid
starter,passing
20A
D
NQS
3A
E
Grip Heating
5A
F
Injection
20A
G
ECU power supply
3A
H
Side stand switch
3A
Note
The system wiring diagram is at the end of this
manual.
92
DUCum_1000DS####03_###e.book Page 93 Wednesday, March 12, 2003 4:33 PM
FOR UNITED STATES OF AMERICA VERSION
ONLY
Safety warnings
Traffic Rules vary from jurisdiction to jurisdiction. Know the
regulations in your jurisdiction before riding this
motorcycle.
Noise emission warranty
Ducati Motor S.p.A. warrants that this exhaust system, at
the time of sale, meets all applicable U.S. EPA Federal
noise standards. This warranty extends to the first person
who buys this exhaust system for purposes other than
resale, and to all subsequent buyers. Warranty claims
should be directed to: Ducati North America, Inc., 237
West Parkway, Pompton Plains, New Jersey, 07444-1028
Tel: 001.973.839-2600 • Fax: 001.973.839-2331.
Noise and exhaust emission control system
information
Source of Emissions
The combustion process produces carbon monoxide and
hydrocarbons. Control of hydrocarbons is very important
because under certain conditions, they react to form
photochemical smog when subjected to sunlight. Carbon
monoxide does not react in the same way, but is toxic.
Ducati utilizes lean carburetor settings and other systems
to reduce carbon monoxide and hydrocarbons.
93
E
USA
Reporting of safety defects
If you believe that your vehicle has a defect which could
cause a crash or could cause injury or death, you should
immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Ducati
North America. If NHTSA receives similar complaints, it
may open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order a recall
and remedy campaign. However, NHTSA cannot become
involved in individual problems between you, your dealer,
or Ducati North America. To contact NHTSA, you may
either call the Auto Safety Hotline toll-free at 1-800-4249393 (or 366-0123 in Washington, D.C. area) or write to:
NHTSA, U.S. Department of Transportation, Washington,
D.C. 20590. You can also obtain other information about
motor vehicle safety from the Hotline.
Warning
This motorcycle is designed and intended for use on
streets and other smooth, paved areas only. Do not use
this motorcycle on unpaved surfaces. Such use could lead
to upset or other accident.
DUCum_1000DS####03_###e.book Page 94 Wednesday, March 12, 2003 4:33 PM
Exhaust Emission Control System
The Exhaust Emission Control System is composed of
lean carburetor settings, and no adjustments should be
made except idle speed adjustments with the throttle stop
screw. The Exhaust Emission Control System is separate
from the crankcase emission control system.
USA
E
Crankcase Emission Control System
The engine is equipped with a closed crankcase system to
prevent discharging crankcase emissions into the
atmosphere. Blow-by gas is returned to the combustion
chamber through the air cleaner and the throttle body.
Evaporative Emission Control System
California motorcycles are equipped with an evaporative
emission control system which consists of a charcoal
canister and associated piping. This system prevents the
escape of fuel vapors from the throttle body and fuel tank.
Tampering warning
Tampering with Noise Control System Prohibited. Federal
Law prohibits the following acts or causing thereof:
(1) the removal or rendering inoperative by any person,
other than for purposes of maintenance, repair, or
replacement, of any device or element of design
incorporated into any new vehicle for the purpose of noise
control prior to its sale or delivery to the ultimate purchaser
or while it is in use; or
94
(2) the use of the vehicle after such device or element of
design has been removed or rendered inoperative by any
person.
Among those acts presumed to constitute tampering
are the acts listed below:
(1) Removal of, or puncturing the muffler, baffles, header
pipes or any other component which conducts exhaust
gases.
(2) Removal or puncturing of any part of the intake system.
(3) Lack of proper maintenance.
(4) Replacing any moving part of the vehicle, or parts of the
exhaust or intake system, with parts other than those
specified by the manufacturer.
This product should be checked for repair or replacement
if the motorcycle noise has increased significantly through
use. Otherwise, the owner may become subject to
penalties under state and local ordinances.
Problems that may affect motorcycle emissions
If you are aware of any of the following symptoms, have
the vehicle inspected and repaired by your local Ducati
dealer.
Symptoms:
Hard starting or stalling after starting.
Rough idle.
Misfiring or backfiring during acceleration.
After-burning (backfiring).
Poor performance (driveability) and poor economy.
DUCum_1000DS####03_###e.book Page 95 Wednesday, March 12, 2003 4:33 PM
When the roadway is wet, rely more on the throttle to
control vehicle speed and less on the front and rear brakes.
The throttle should also be used judiciously to avoid
skidding the rear wheel from too rapid acceleration or
deceleration.
On rough roads, exercise caution, slow down, and grip the
fuel tank with your knees for better stability.
When quick acceleration is necessary as in passing, shift
to a lower gear to obtain the necessary power.
Do not down shift at too high an r.p.m. to avoid damage to
the engine from overreving.
Avoiding unnecessary weaving is important to the safety
of both the rider and other motorists.
Do not exceed the legal speed limit or drive too fast for
existing conditions. High speed increases the influence of
any condition affecting stability and the loss of control.
Operate motorcycle only at moderate speed and out of
traffic until you have become thoroughly familiar with its
operation and handling characteristics under all conditions.
This is a very high performance motorcycle, designed and
intended for use by experienced careful riders only!
A new motorcycle must be operated according to a special
break-in procedure (see Running in recommendations).
Warning
Before starting engine, check for proper operation of
brake, clutch, shifter, throttle controls, correct fuel and oil
supply.
Gasoline is extremely flammable and is explosive under
certain conditions. Refuell in a well ventilated area with the
engine stopped. Do not smoke or allow open flames or
95
E
USA
Riding safety
The points given below are applicable for every day
motorcycle use and shoud be carefully observed for safe
and effective vehicle operation.
A motorcycle does not provide the impact protection of an
automobile, so defensive riding in addition to wearing
protective apparel is extremely important.
Do not let protective apparel give you a false sense of
security.
Before changing lanes, look over your shoulder to make
sure the way is clear. Do not rely solely on the rear view
mirror; you may misjudge a vehicle’s distance and speed,
or you may not see it at all.
When going up steep slopes, shift to a lower gear so that
there is plenty of power to spare rather than overloading
the engine.
When applying the brakes, use both the front and rear
brakes. Applying only one brake for sudden braking may
cause the motorcycle to skid and lose control.
When going down long slopes, control vehicle speed by
closing the throttle. Use the front and rear brakes for
auxiliary braking.
Riding at the proper rate of speed and avoiding
unnecessarily fast acceleration are important not only for
safety and low fuel consumption but also for long vehicle
life and quieter operation.
When riding in wet conditions or on loose roadway
surfaces, the ability to maneuver will be reduced. All of
your actions should be smooth under these conditions.
Sudden acceleration, braking or turning may cause loss of
control.
DUCum_1000DS####03_###e.book Page 96 Wednesday, March 12, 2003 4:33 PM
USA
E
sparks when refuelling or servicing the fuel system.
Always close the fuel petcock when the engine is not
running to prevent flooding of the throttle body. Do not
overfill fuel tank (see instructions page 51).
Motorcycle exhaust contains poisonous carbon monoxide
gas. Do not inhale exhaust gases and never run the engine
in a closed garage or confined area.
Use only Ducati approved parts and accessories.
This motorcycle was not intended to be equipped with a
sidecar or to be used to tow any trailer or other vehicle.
Ducati does not manufacture sidecars or trailers and
cannot predict the effects of such accessories on handling
or stability, but can only warn that the effects will be
adverse and any damage to motorcycle components
caused by the use of such accessories will not be
remedied under warranty.
Warning
Do not ride the motorcycle with helmets attached to
the hook; the helmets could cause an accident by
distracting the operator or interfering with normal vehicle
operation.
The exhaust system becomes very hot during operation,
never touch the exhaust system. Wear clothing that fully
covers your legs. Do not wear loose clothing which could
catch on the control levers, footrests, wheels, or chain.
Any amount of alcohol will significantly interfere with your
ability to safely operate your motorcycle. Don’t drink and
ride.
Vehicle identification number (VIN);
Every Ducati motorcycle is identified by two identification
numbers (see page 9). Figure A specifically shows the
frame identification numbers.
DUCATI
TYPE OF
MOTORCYCLE
MODEL
YEAR
SEQUENTIAL
NUMBER
{
{
{
Protective apparel
Always wear a helmet. Most motorcycle accident fatalities
are due to head injuries.
For safety eye protection, gloves, and high top, sturdy
boots should also be worn.
PLANT OF
MANUFACTURE
ZDM 1V A B P ★ 3 B 0 0 0 0 0 0
★ Varies-can be thru 9 or X (Check digit)
fig. A
96
DUCum_1000DS####03_###e.book Page 97 Wednesday, March 12, 2003 4:33 PM
Label location (fig. B)
2
1
8
7
9
3
E
USA
6
5
4
fig. B
97
DUCum_1000DS####03_###e.book Page 98 Wednesday, March 12, 2003 4:33 PM
OBJECT IN MIRROR ARE
CLOSER THAN THEY APPEAR
Cod. 433 1 166 1A
1
WARNING
DO NOT ATTEMPT TO LOOK THROUGH THIS FAIRING. THIS IS NOT
A WINDSHIELD, BUT AN AERODYNAMIC FAIRING ONLY; FAILURE
TO OBSERVE THIS WARNING COULD RESULT IN A COLLISION OR
UPSET AND CONSEQUENT SERIOUS BODILY INJURY.
Cod. 433 1 165 1A
Tensione catena (sul cavalletto laterale)
Chain tension adjustment (on side stand)
HELMET HOLDER
UNDER THE SEAT
3
2
38 ÷ 42 mm
Cod. 433.1.312.1A
4
Manufactured by
MOTORCYCLE NOISE EMISSION CONTROL INFORMATION
Cod. 432 1 233 1A
5
USA
VEHICLE EMISSION CONTROL INFORMATION
THIS VEHICLE CONFORMS TO U.S. EPA AND
CALIFORNIA REGULATIONS APPLICABLE TO 1998
MODEL YEAR NEW MOTORCYCLES AND IS
CERTIFIED TO 1.4 HC G/KM ENGINE FAMILY
EXHAUST EMISSION STANDARD IN CALIFORNIA
ENGINE TUNE-UP SPECIFICATIONS
ITEM
IGNITION TIMING:
IDLE SPEED (RPM):
IDLE MIXTURE:
SPECIFICATIONS
2 bTDC at idle speed
1200 ± 0.12 mm
INSTRUCTIONS
No adjustment
No adjustment
No adjustment
Opening 0.05 ± 0.12 mm
VALVE CLEARANCE (in & ex):
See Service Manual
Closing 0.03 ± 0.12 mm
SPARK PLUG: CHAMPION RA4HC
OIL: SAE 20W50
SPARK PLUG GAP (mm): 0.5 ÷ 0.6
FUEL: Unleaded gasoline
- BOLOGNA - ITALY
7
VEHICLE EMISSION CONTROL LABEL
CANISTER
ENGINE DISPLACEMENT :992 cc. ENGINE FAMILY :
THIS VEHICLE CONFORMS TO U.S. EPA AND CALIFORNIA REGULATIONS
APPLICABLE TO
MODEL YEAR NEW MOTORCYCLES.
EVAP FAMILY :
DUCATI
Via A. C. Ducati, 3
40132 BOLOGNA
HOT AIR INLET
ITALY
TO HORIZONTAL MANIFOLD
TO VERTICAL MANIFOLD
9
98
Vehicle I.D. No.: ZDM1TB9PXWB000001
CAUTION
Engine displacement: 904 cc
Engine family: WDUCC0944ST2
Engine exhaust control system: MFI
Evap family:
NEVER FILL TANK SO FUEL LEVEL RISES INTO FILLER
NECK. IF TANK IS OVERFILLED, HEAT MAY CAUSE FUEL
TO EXPAND AND FLOW INTO EVAPORATIVE EMISSION
CONTROL SYSTEM RESULTING IN HARD STARTING AND
ENGINE HESITATION.
8
DATE:
07/97
GVWR: 925.9 Lbs (420 kg)
GAWR front: 319.7 Lbs (145 kg) with 120/70ZR17 tire, MT 3.50x17 RIM at 32.7 PSI cold.
GAWR rear: 606.2 Lbs (275 kg) with 170/60ZR17 tire, MT 5.50x17 RIM at 36.9 PSI cold.
This vehicle conforms to all applicable Federal Motor Vehicle Safety standards in effect on the date
of manufacture shown above.
Type classification: Motorcycle
6
432 1 416 1D
E
THIS 1998 DUC46P0944 MOTORCYCLE, ZDM1TB9PXWB000001
MEETS EPA NOISE EMISSION REQUIREMENTS OF 80 dBA AT 4675 RPM BY
THE FEDERAL TEST PROCEDURE.
MODIFICATIONS WHICH CAUSE THIS MOTORCYCLE TO EXCEED FEDERAL
NOISE STANDARDS ARE PROHIBITED BY FEDERAL LAW.
SEE OWNER'S MANUAL.
Cod. 432 1 234 1A
DUCum_1000DS####03_###e.book Page 99 Wednesday, March 12, 2003 4:33 PM
California evaporation emission system
This system consists of (fig. C):
fig. C
I. Coverage
Warranty defects shall be remedied during customary
business hours at any authorized Ducati motorcycle dealer
located within the United States of America in compliance
with the Clean Air Act and applicable regulations of the
99
E
USA
CANISTER
Important
In the event of fuel system malfunction, contact
Ducati’s authorized Service Centres.
Ducati limited warranty on emission control
system
Ducati North America, Inc., 237 West Parkway, Pompton
Plains, New Jersey 07444-1028 warrants that each new
1998 and later Ducati motorcycle, that includes as
standard equipment a headlight, tail-light and stoplight,
and is street legal:
A) is designed, built and equipped so as to conform at the
time of initial retail purchase with all applicable regulations
of the United States Environmental Protection Agency,
and the California Air Resources Board; and
B) is free from defects in material and workmanship which
cause such motorcycle to fail to conform with applicable
regulations of the United States Environmental Protection
Agency or the California Air Resources Board for a period
of use, depending on the engine displacement,of 12,000
kilometers (7,456 miles), if the motorcycle’s engine
displacement is less than 170 cubic centimeters; of
18,000 kilometers (11,185 miles), if the motorcycle’s
engine displacement is equal to or greater than 170 cubic
centimeters but less than 280 cubic centimeters; or of
30,000 kilometers (18,641 miles), if the motorcycle’s
engine displacement is 280 cubic centimeters or greater;
or 5 (five) years from the date of initial retail delivery,
whichever first occurs.
DUCum_1000DS####03_###e.book Page 100 Wednesday, March 12, 2003 4:33 PM
USA
E
United States Environmental Protection Agency and the
California Air Resources Board. Any part or parts replaced
under this warranty shall become the property of Ducati.
In the state of California only, emissions related warranted
parts are specifically defined by that state’s Emissions
Warranty Parts List. These warranted parts are: carburetor
and internal parts; intake manifold; fuel tank, fuel injection
system; spark advance mechanism; crankcase breather;
air cutoff valves; fuel tank cap for evaporative emission
controlled vehicles; oil filler cap; pressure control valve;
fuel/vapor separator; canister; igniters; breaker governors;
ignition coils; ignition wires; ignition points, condensers,
and spark plugs if failure occors prior to the first scheduled
replacement, and hoses, clamps, fittings and tubing used
directly in these parts. Since emission related parts may
vary from model to model, certain models may not contain
all of these parts and certain models may contain
functionally equivalent parts.
In the state of California only, Emission Control System
emergency repairs, as provided for in the California
Administrative Code, may be performed by other than an
authorized Ducati dealer. An emergency situation occurs
when an authorized Ducati dealer is not reasonably
available, a part is not available within 30 days, or a repair
is not complete within 30 days. Any replacement part can
be used in an emergency repair. Ducati will reimburse the
owner for the expenses, including diagnosis, not to
exceed Ducati’s suggested retail price for all warranted
parts replaced and labor charges based on Ducati’s
recommended time allowance for the warranty repair and
the geographically appropriate hourly labor rate. The
100
owner may be required to keep receipts and failed parts in
order to receive compensation.
II. Limitations
This Emission Control System Warranty shall not cover
any of the following:
A. Repair or replacement required as a result of
(1) accident,
(2) misuse,
(3) repairs improperly performed or replacements
improperly installed,
(4) use of replacement parts or accessories not
conforming to Ducati specifications which adversely affect
performance and/or
(5) use in competitive racing or related events.
B. Inspections, replacement of parts and other services
and adjustments required for routine maintenance.
C. Any motorcycle on which odometer mileage has been
changed so that actual mileage cannot be readily
determined.
III. Limited liability
A. The liability of Ducati under this Emission Control
Systems Warranty is limited solely to the remedying of
defects in material or workmanship by an authorized
Ducati motorcycle dealer at its place of business during
customary business hours. This warranty does not cover
inconvenience or loss of use of the motorcycle or
transportation of the motorcycle to or from the Ducati
dealer. Ducati shall not be liable for any other expenses,
loss or damage, whether direct, incidental, consequential
DUCum_1000DS####03_###e.book Page 101 Wednesday, March 12, 2003 4:33 PM
performed at a service establishment or by any individual.
The warranty period begins on the date the motorcycle is
delivered to an ultimate purchaser.
Ducati North America, Inc..
237 West Parkway
Pompton Plains, New Jersey, 07444-1028
001.973.839-2600
E
USA
or exemplary arising in connection with the sale or use of
or inability to use the Ducati motorcycle for any purpose.
Some states do not allow the exclusion or limitation of any
incidental or consequential damages, so the above
limitations may not apply to you.
B. No express emission control system warranty is given
by Ducati except as specifically set forth herein. Any
emission control system warranty implied by law,
including any warranty of merchantability or fitness for a
particular purpose, is limited to the express emission
control systems warranty terms stated in this warranty.
The foregoing statements of warranty are exclusive and in
lieu of all other remedies. Some states do not allow
limitations on how long an implied warranty lasts so the
above limitation may not apply to you.
C. No dealer is authorized to modify this Ducati Limited
Emission Control Systems Warranty.
IV. Legal rights
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
V. This warranty is in addition to the Ducati limited
motorcycle warranty.
VI. Additional information
Any replacement part that is equivalent in performance
and durability may be used in the performance of any
maintenance or repairs. However, Ducati is not liable for
these parts. The owner is responsible for the performance
of all required maintenance. Such maintenance may be
101
DUCum_1000DS####03_###e.book Page 102 Wednesday, March 12, 2003 4:33 PM
ROUTINE MAINTENANCE RECORD
Km
1,000
10,000
20,000
E
30,000
USA
40,000
50,000
102
Ducati
Service Name
Mileage
Date