Dukane 8412 Projector User Manual

DUKANE CORP AV DIVISION
USER MANUAL
MODEL 8412
DATA VIDEO PROJECTOR
Information in this Guide may change due to product improvements. To obtain the latest
manuals, literature, and software please visit the Dukane web site at; www.dukane.com/av
and look at the specific model SUPPORT or DOWNLOADS section.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
avservice@dukane.com
www.dukane.com/av
File M: PRODUCTS / Projectors / 8408 / Manual
Table of Contents
Table of Contents.............................1
Usage Notice....................................2
Safety Information................................2
Precautions..........................................3
Eye Safety Warnings...........................5
Product Features.................................5
Introduction.......................................6
Package Overview...............................6
Product Overview................................7
Main Unit............................................... 7
Control Panel........................................ 8
Input/Output Connections..................... 9
Remote Control................................... 10
Installation...................................... 11
Connecting the Projector...................11
Connect to Computer/Notebook......... 11
Connect to Video Sources.................. 12
Powering the projector On / Off.........13
SETUP | Advanced............................. 41
SETUP | Network................................ 42
OPTIONS............................................ 47
OPTIONS | Advanced......................... 48
OPTIONS | Lamp Settings.................. 49
Appendices.....................................50
Troubleshooting.................................50
Replacing the lamp............................55
Compatibility Modes..........................57
Computer Compatibility...................... 57
Video Compatibility............................. 58
RS232 Commands and Protocol
Function List......................................59
RS232 Pin Assignments..................... 59
RS232 Protocol Function List............. 60
Ceiling Mount Installation...................64
Optoma Global Offices......................65
Regulation & Safety Notices..............67
Powering On the Projector.................. 13
Powering off the projector.................. 14
Warning Indicator................................ 14
Adjusting the Projected Image...........15
Adjusting the Projector’s Height ........ 15
Adjusting the Projector’s Focus.......... 16
Adjusting Projection Image Size......... 16
User Controls.................................18
Control Panel & Remote Control.......18
Control Panel...................................... 18
Remote Control................................... 19
On-screen Display Menus.................24
How to operate .................................. 24
Menu Tree........................................... 25
IMAGE................................................ 27
IMAGE | Advanced............................. 29
DISPLAY............................................. 31
DISPLAY | 3D .................................... 34
SETUP................................................ 35
SETUP | Signal (RGB)........................ 38
SETUP | Security................................ 39
1
English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1.Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air flow.
2.Do not use the projector near water or moisture. To reduce the risk
of fire and/or electric shock, do not expose the projector to rain or
moisture.
3.Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as amplifiers that emits heat.
4.Clean only with dry cloth.
5.Only use attachments/accessories specified by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call 'XNDQH
before you send the unit for repair.
7.Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in fire or
electric shock.
8.See projector enclosure for safety related markings.
9.The unit should only be repaired by appropriate service personnel.
English
2
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
55-56.
▀■ Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 49).
▀■ Warning- When switching the projector off, please ensure
When the lamp
reaches the end
of its life, the projector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 55-56.
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
▀■ Warning- Do not look into or point the laser pointer on your
remote control into your or someone’s eyes. Laser
pointer can cause permanent damage to eyesight.
3
English
Usage Notice
Do:
 Turn off and unplug the power plug from the AC outlet before
cleaning the product.
 Use a soft dry cloth with mild detergent to clean the display
housing.
 Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
 Block the slots and openings on the unit provided for
ventilation.
 Use abrasive cleaners, waxes or solvents to clean the unit.
 Use under the following conditions:
- In extremely hot, cold or humid environments.
Ensure that the ambient room temperature is within
5 - 35°C.
Relative Humidity is 5 - 35°C, 80% (Max.),
English
4
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
Usage Notice
Eye Safety Warnings
▀■ Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
▀■ In order to minimize the lamp power, use room blinds to
reduce ambient light levels.
Product Features
▀■ XGA (1024x768) Native resolution /
WXGA (1280x800) Native resolution
▀■ HD compatible – 1080p supported
Monitor loop
through only support in VGA1-In/
SCART/YPbPr.
▀■ VGA monitor loop through
(works on standby mode > 1W)
▀■ BrilliantColorTM Technology
▀■ Security Bar and Kensington Lock
▀■ RS232 control
▀■ Rapid shutdown
▀■ Built-in speakers
▀■ Network support
5
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Projector with lens cap
Due to different
applications in
each Country,
some regions
may have
different
accessories.
2 × AAA Batteries
Documentation :
User’s Manual

Warranty Card

Quick Start Card

WEEE Card

English
6
(for EMEA only)
Power Cord 1.8m
IR Remote Control
VGA Cable 1.8m
Introduction
Product Overview
Main Unit
6
1
2
4
3
6
5
4
7
8
4
4
9
4
10
11
Air Flow
1.
2.
3.
4.
5.
6.
Control Panel
Focus Ring
Speaker
Tilt-Adjustment Feet
Lens
IR Receiver
7. Input / Output
Connections
8. Power Socket
9. Security Bar
10.Ventilation (inlet)
11. Ventilation (outlet)
7
English
Introduction
Control Panel
2
3
4
11
SO
URCE
1
LAMP
TEMP
MENU
HELP
POWER/STANDBY
10
9
8
7
6
1. Source
2. Enter
3. Re-Sync
4. IR Receiver
5. Temp LED
6. Help
7. Four Directional Select Keys
8. Power/Standby button and LED
9. Keystone Correction
10.Menu
11. Lamp LED
English
8
5
Introduction
Input/Output Connections
1
2
RJ-45
USB
3
HDMI
4
VGA-OUT
5
VGA1-IN / SCART / YPbPr
VGA2-IN / YPbPr
6
7
S-VIDEO
MIC
VIDEO
8
RS-232
9
AUDIO1-IN
(VGA1/VGA2)
12V OUT
AUDIO 2-IN (S-VIDEO/VIDEO)
L
10
R
AUDIO OUT
12V OUT
17
Monitor loop
through only support in VGA1-In/
SCART/YPbPr.
16
15
14
13
12
11
1. RJ-45 Networking Connector
2. USB Connector (Connect to PC for Remote Mouse function)
3. HDMI Connector
4. VGA-Out Connector (Monitor Loop-through Output)
5. VGA1-In/SCART/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr/
SCART)
6. S-Video Input Connector
7. Composite Video Input Connector
8. RS-232 Connector (3-pin DIN Type)
9. Audio 1 Input connector (3.5mm mini jack)
(for VGA1/VGA2)
10.12V Trigger Relay Connector (12V, 750mA)
11. Security Bar
12.Audio Output Connector (3.5mm Mini Jack)
13.KensingtonTM Lock Port
14.RCA Audio 2 Input connector (Left & Right)
(for S-Video/Video)
15.Microphone Input Connector
16.VGA2-In/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
17.Power Socket
9
English
Introduction
Remote Control
1
2
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
11
21
English
10
22
23
1. LED Indicator
2. Power On/Off
3. Four Directional
Select Keys
4. Mouse Right Click
5. Page Up
6. Re-Sync
7. Page Down
8. Volume +/9. 3D
10.AV mute
11. Video
12.PC/Mouse control
13.Mouse Left Click
14.Enter/Help
15.Source
16.Keystone +/17.Menu
18.Brightness
19.HDMI
20.S-Video
21.Numbered keypad
(for password input)
22.Freeze
23.VGA
Installation
Connecting the Projector
Connect to Computer/Notebook
+12V Output
MOLEX
3
2
5
7
4
6
molex
RJ-45
VGA-OUT
VGA1-IN / SCART / YPbPr
VGA2-IN / YPbPr
1
S-VIDEO
MIC
VIDEO
RS-232
AUDIO1-IN
(VGA1/VGA2)
12V OUT
AUDIO 2-IN (S-VIDEO/VIDEO)
L
R
AUDIO OUT
PS50426E
(*) Optional
accessory
HDMI
R
Due to the
difference in
applications
for each
country, some
regions may
have different
accessories.
USB
9
8
Audio Output
1....................................................................................................Power Cord
2..............................................................................................*Network Cable
3....................................................................................................*USB Cable
4...........................................................................................*DVI/HDMI Cable
5.....................................................................................................VGA Cable
6................................................................................................*RS232 Cable
7.........................................................................................*Audio Input Cable
8........................................................................................*VGA Output Cable
9......................................................................................*Audio Output Cable
11
English
Installation
Connect to Video Sources
DVD Player, Set-top Box,
HDTV receiver
S-Video Output
6
4
7
Composite Video Output
8
2
5
3
+12V Output
RJ-45
USB
HDMI
VGA-OUT
1
VGA1-IN / SCART / YPbPr
VGA2-IN / YPbPr
S-VIDEO
MIC
VIDEO
RS-232
AUDIO1-IN
(VGA1/VGA2)
12V OUT
AUDIO 2-IN (S-VIDEO/VIDEO)
L
R
AUDIO OUT
R
PS50426E
9
Audio Output
Due to the
difference in
applications
for each
country, some
regions may
have different
accessories.
(*) Optional
accessory
English
12
10
11
8
1....................................................................................................Power Cord
2..................................................................................................*HDMI Cable
3........................................................................................ *Microphone Cable
4................................................................................... *SCART/VGA Adaptor
5.....................................................................................................VGA Cable
6.............................................................................................. *S-Video Cable
7................................................................................*Composite Video Cable
8.................................................................................*Audio Cable Jack/RCA
9................................................*15-Pin to 3 RCA Component/HDTV Adaptor
10...........................................................................*3 RCA Component Cable
11................................................................................*Audio Cable RCA/RCA
Installation
Powering the projector On / Off
Powering On the Projector

When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
1. Remove the lens cap. 
2. Securely connect the power cord and signal cable. When
connected, the POWER/STANDBY LED will turn Amber.
3. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The POWER/STANDBY LED
will now turn Green. 
The startup screen will display in approximately 10 seconds.
The first time you use the projector, you will be asked to
select the preferred language and power saving mode.
4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
2
POWER/STANDBY
SO
URCE
If you connect multiple sources at the same time, press the
“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.
LAMP
TEMP
MENU
HELP
POWER/STANDBY
Turn on the
projector first and
then select the
signal sources.
1
Lens Cap
13
English
Installation
Powering off the projector
1. Press the “ ” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to confirm otherwise the
message will disappear after 15 seconds. When you
press the “ ” button for the second time, the projector will
display countdown timer and will shut down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the POWER/STANDBY LED will
Flash Green. When the POWER/STANDBY LED lights
solid Amber, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
4. Do not turn on the projector immediately following a power
off procedure.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
65-66 for more
information.
English
14
 “LAMP” LED indicator is lit red and if “POWER/STANDBY”
indicator flashes amber.
 “TEMP” LED indicator is lit red and if “POWER/STANDBY”
indicator flashes amber. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
 “TEMP” LED indicator flashes red and if “POWER/STANDBY” indicator flashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1.Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
15
English
Installation
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear.
XGA series: The projector will focus at distances from 1.64
to 12.46 feet (0.5 to 3.8 meters).
WXGA series: The projector will focus at distances from 1.64
to 11.15 feet (0.5 to 3.4 meters).
Focus Ring
Adjusting Projection Image Size
XGA series: Projection Image Size from 41.0” to 312.0” (1.0
to 7.9 meters).
WXGA series: Projection Image Size from 44.6” to 303.0”
(1.1 to 7.7 meters).
Top View
Screen
Screen (W)
Height
Projection Distance (D)
Screen
Side View
Offset (Hd)
Projection Distance (D)
English
16
Screen (H)
Dia
go
na
Width
l
Installation
XGA
Diagonal length
(inch) size of
4:3 Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
wide
tele
wide
tele
(m)
40.00
0.81
0.61
31.89
24.02
0.50
0.50
1.64
1.64
0.09
(feet)
0.30
60.00
1.22
0.91
48.03
35.83
0.80
0.80
2.62
2.62
0.14
0.45
70.00
1.42
1.07
55.91
42.13
0.90
0.90
2.95
2.95
0.16
0.53
80.00
1.63
1.22
64.17
48.03
1.00
1.00
3.28
3.28
0.18
0.60
90.00
1.83
1.37
72.05
53.94
1.10
1.10
3.61
3.61
0.21
0.67
100.00
2.03
1.52
79.92
59.84
1.30
1.30
4.26
4.26
0.23
0.75
120.00
2.44
1.83
96.06
72.05
1.50
1.50
4.92
4.92
0.27
0.90
150.00
3.05
2.29
120.08
90.16
1.90
1.90
6.23
6.23
0.34
1.13
180.00
3.66
2.74
144.09
107.87
2.30
2.30
7.54
7.54
0.41
1.35
250.00
5.08
3.81
200.00
150.00
3.20
3.20
10.50
10.50
0.57
1.87
300.00
6.10
4.57
240.16
179.92
3.66
3.66
12.01
12.01
0.69
2.25
This table is for user’s reference only.
WXGA
Diagonal length
(inch) size of
16:10 Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
wide
tele
wide
tele
(m)
40.00
0.86
0.54
33.86
21.26
0.40
0.40
1.31
1.31
0.07
(feet)
0.22
60.00
1.29
0.81
50.79
31.89
0.70
0.70
2.30
2.30
0.10
0.33
70.00
1.51
0.94
59.45
37.01
0.80
0.80
2.62
2.62
0.12
0.38
80.00
1.72
1.08
67.72
42.52
0.90
0.90
2.95
2.95
0.13
0.44
90.00
1.94
1.21
76.38
47.64
1.00
1.00
3.28
3.28
0.15
0.49
100.00
2.15
1.35
84.65
53.15
1.10
1.10
3.61
3.61
0.17
0.55
120.00
2.58
1.62
101.57
63.78
1.30
1.30
4.26
4.26
0.20
0.66
150.00
3.23
2.02
127.17
79.53
1.70
1.70
5.58
5.58
0.25
0.82
180.00
3.88
2.42
152.76
95.28
2.00
2.00
6.56
6.56
0.30
0.98
250.00
5.38
3.37
211.81
132.68
2.80
2.80
9.18
9.18
0.42
1.37
300.00
6.46
4.04
254.33
159.05
3.36
3.36
11.03
11.03
0.50
1.64
This table is for user’s reference only.
17
English
User Controls
Control Panel & Remote Control
SO
URCE
Control Panel
LAMP
MENU
TEMP
HELP
POWER/STANDBY
Using the Control Panel
English
18
POWER
Refer to the “Power On/Off the Projector” section on
pages 13-14.
RE-SYNC
Automatically synchronize the projector to the input
source.
Enter
Confirm your item selection.
SOURCE
Press “SOURCE” to select an input signal.
Menu
Press “Menu” to launch the on-screen display
(OSD) menu. To exit OSD, Press “Menu” again.
Four Directional
Select Keys
Use
to select items or make adjustments to your selection.
Keystone
Use
to adjust image distortion caused
by tilting the projector. (±40 degrees)
HELP
Help Menu (refer to page 21).
Lamp LED
Indicate the projector’s lamp status.
Temp LED
Indicate the projector’s temperature status.
POWER/
STANDBY
LED
Indicate the projector’s status.
User Controls
Remote Control
Using the Remote Control
Power
Refer to the “Power On/Off the Projector”
section on pages 13-14.
L Button
Mouse left click.
R Button
Mouse right click.
Page +
Use this button to page up.
Page -
Use this button to page down.
Enter
/ Help
Confirm your item selection.
Help Menu (refer to page 21).
Source
Press “Source” to select an input signal.
Re-SYNC
Automatically synchronizes the projector to
the input source.
Four Directional
Select Keys
Use
to select items or make
adjustments to your selection.
Keystone +/-
Adjust image distortion caused by tilting the
projector.
Volume +/-
Adjust to increase / decrease the volume.
Brightness
Adjust the brightness of the image.
3D
Press the “3D” to turn the 3D OSD menu
on/off.
Menu
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, press
“Menu” again.
HDMI
Press “HDMI” to choose HDMI source.
Freeze
Press “Freeze” to pause the screen image.
Press this button again to unlock.
19
English
User Controls
Using the Remote Control
English
20
AV mute
Momentarily turns off/on the audio and
video.
S-Video
Press “S-Video” to choose S-Video source.
VGA
Press “VGA” to choose VGA sources.
Video
Press “Video” to choose Composite video
source.
User Controls
Using the HELP button
The HELP function ensures easy setup and operation.
Press the “?” button on the remote control or press the
“HELP” button on the control panel to open the Help Menu.
21
English
User Controls
Help menu button functions only when no input source
is detected.
Please refer to the
“Troubleshooting”
section on pages
50-54 for more
details.
If input source is detected and help button is pressed, the
following pages will appear to help diagnose any problems.
English
22
User Controls
23
English
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2 When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use
using
keys to select the desired item and adjust the settings
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” to confirm, and the screen will return to the main
menu.
6. To exit, press “MENU” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
Sub Menu
Settings
English
24
User Controls
Menu Tree
Main Menu
Sub Menu
Image
Display Mode
Settings
Brightness
Presentation / Bright / Movie / sRGB /
Blackboard / Classroom / User / 3D
ʳ
Contrast
ʳ
Sharpness
#1
Saturation
#1
Tint
Advanced
Degamma
Film / Video / Graphics / PC
BrilliantColor™
0~10
Color Temp.
Warm / Medium / Cold
Color
Color Space
Red Gain / Green Gain / Blue Gain / Red
Bias / Green Bias / Blue Bias / Cyan /
Magenta / Yellow / Reset / Exit
AUTO / RGB / YUV
Input Source
VGA1 / VGA2 / Video / S-Video / HDMI
Image AI
On / Off
Exit
Display
Format
#2
#3
Overscan
Zoom
H Image Shift
V Image Shift
V Keystone
Auto Keystone
3D
#4
Setup
#3
3D
3D Sync. Invert
Exit
4:3 / 16:9-1 / 16:9-II / Native / AUTO
4:3 / 16:9 / 16:10 / LBX / Native / AUTO
0~10
80%~200%
-50 ~ +50
-50 ~ +50
-40 ~ +40
On / Off
Off / On
On / Off
Language
English / Deutsch / Français / Italiano /
Español / Português / Svenska /
Nederlands / Norsk/Dansk / Polski /
Suomi / Ɋɭɫɫɤɢɣ / İȜȜȘȞȚțȐ / Magyar /
ýeština / ̶γέΎϓ / ϲΑήϋ /᜗᧯խ֮ʳ/ 亞᫿խ֮ʳ/
ֲ‫ء‬፿!0ᾂ᝖᱑ʳ/ ࡷࡎ࡙/ Türkçe / ViӋt
Screen Type
Projection
16:10 / 16:9
Menu Location
#5
Signal
Security
Automatic
Phase (VGA)
Frequency (VGA)
H. Position (VGA)
V. Position (VGA)
Exit
Security
Security Timer
Change Password
Exit
On / Off
0~31
-5~5
-5~5
-5~5
ʳ
On / Off
Month / Day / Hour
ʳ
25
English
User Controls
Main Menu
Setup
Sub Menu
Advanced
RS232
Network
Options
Settings
Projector ID
Mute
#6
Volume
Audio Input
Source Lock
High Altitude
Information Hide
Keypad Lock
Background Color
Advanced
Lamp Settings
Logo
Logo Capture
Closed Captioning
Exit
0~99
On / Off
0~10
Default / Audio1(Phone jack) / Audio2
(RCA R/L) / MIC
Optoma / User
Off / CC1 / CC2
RS232 / Network
Network State
DHCP
IP Address
Subnet mask
Gateway
DNS
Apply
Exit
Direct Power On
Auto Power Off (min.)
Sleep Timer (min.)
Power Mode (Standby)
Exit
Lamp Hours
Lamp Reminder
Brightness Mode
Lamp Reset
Exit
Yes / No
On / Off
On / Off
On / Off
On / Off
Black / Red / Blue / Green / White
On / Off
0~180
0~995
Eco. / Active
On / Off
STD/Bright
Yes / No
Reset
Please note that the on-screen display (OSD) menus vary according to the
signal type selected and the projector model you are using.
(#1) “Saturation” and “Tint” are only supported in Video mode.
(#2) For XGA model only.
(#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
(#4) “3D Sync Invert” is only available when 3D is enabled.
(#5) “Signal” is only supported in Analog VGA (RGB) signal.
(#6) MIC volume can also be controlled by setup  volume in OSD
English
26
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Moive: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
Classroom: This mode is recommended for projecting in a
classroom.
User: User’s settings.
3D: Recommand setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further
use.
Brightness
Adjust the brightness of the image.
Press the
Press the
Contrast
to darken image.
to lighten the image.
The contrast controls the degree of difference between the lightest
and darkest parts of the picture.
Press the
Press the
to decrease the contrast.
to increase the contrast.
27
English
User Controls
Sharpness
Adjust the sharpness of the image.
Press the
Press the
Saturation
“Saturation” and
“Tint” functions
are only supported under Video mode.
to decrease the sharpness.
to increase the sharpness.
Adjust a video image from black and white to fully saturated color.
Press the
Press the
Tint
to decrease the amount of saturation in the image.
to increase the amount of saturation in the image.
Adjust the color balance of red and green.
English
28
Press the
Press the
to increase the amount of green in the image.
to increase the amount of red in the image.
User Controls
IMAGE | Advanced
Degamma
This allows you to choose a degamma table that has been
fine-tuned to bring out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
PC: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.
Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
Color
Press
into the next menu as below and then use
select item.
to
or
Red/Green/Blue/Cyan/Magenta/Yellow: Use
Reset: Choose “Yes” to return the factory default settings for
or to select
Red, Green, Blue, Cyan, Magenta and Yellow Colors.
color adjustments.
29
English
User Controls
Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
Input Source
Use this option to enable / disable input sources. Press
to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that
are not selected.
Image AI
Image AI improves the contrast of the picture by optimizing the
brightness of the lamp according to the picture content.
On: The dynamic image performance manager is active in
making sure your greatest pleasure from seeing a movie
dynamically with the most dark details revealed, vivid and
bright image performed all the way.
Off: The dynamic image performance manager is on standby.
English
30
User Controls
DISPLAY
Format
Use this function to choose your desired aspect ratio.
XGA
4:3: This format is for 4×3 input sources.
16:9-I: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (576i/p)
16:9-II: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (480i/p)
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
When input is 4:3, the image is displayed as 4:3. When input is
16:9 above, the image is displayed as 16:9- I
Aspect ratio
(source detected)
Resize image
4:3
1024 x 768 center
16:9-I
1024 x 576 center
XGA model
16:9-II
854 x 480 center
Native
No resize image, 1:1 mapping and
centered. This format shows the
original image without scaling.
31
English
User Controls
WXGA
4:3: This format is for 4×3 input sources.
16:9: This format is for 16×9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
16:9 or 16:10
depend on “Screen
Type” setting.
16:10: This format is for 16×10 input sources, like widescreen
laptops.
LBX: This format is for non-16x9, letterbox source and for users
who use external 16x9 lens to display 2.35:1 aspect ratio using
full resolution.
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
16:10 Screen
480i/p
576i/p
4:3
PC
1066 x 800 center
1280 x 800 center
LBX
1280 x 960 center, then get the central 1280 x 800 image
to display
16:9 Screen
1:1 mapping
centered.
480i/p
576i/p
4:3
1:1 mapping (960 x
540) display
1280 x 800
1280 x 720
center
1:1
mapping
centered.
1080i/p
720p
PC
960 x 720 center
16:9
1280 x 720 center
LBX
1280 x 960 center, then get the central 1280 x 720 image
to display
Native
32
720p
16:10
Native
English
1080i/p
1:1 mapping
centered.
1:1 mapping (960 x
540) display
1280 x 720
1280 x 720
center
1:1
mapping
centered.
User Controls
Overscan
Each I/O has
different setting of
“Overscan”.
Overscan function removes the noise in a video image. Overscan
the image to remove video encoding noise on the edge of video
source.
Zoom
“Overscan” and
“Zoom” can’t work at
same time.
Press the to reduce the size of an image.
Press the to magnify an image on the projection screen.
H Image Shift
Shift the projected image position horizontally.
V Image Shift
Shift the projected image position vertically.
V Keystone
Press the or to adjust image distortion vertically. If the image
looks trapezoidal, this option can help make the image rectangular.
Auto Keystone
Automatically adjusts vertical image distortion.
33
English
User Controls
DISPLAY | 3D
3D
Choose the “On” to turn this item on first if for 3D images.
“3D Sync Invert”
only available when
3D is enabled.
Compatible 3D
source, 3D content
and active shutter
glasses are required
for 3D viewing.
English
34
3D Sync. Invert
Press the “On” to invert left and right frame contents.
Press the “Off” for default frame contents.
User Controls
SETUP
Language
Choose the multilingual OSD menu. Press or into the sub
or
key to select your preferred
menu and then use the
language. Press “Enter” to finalize the selection.
Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.
Projection

Front-Desktop
This is the default selection. The image is projected straight on
the screen.

Rear-Desktop
When selected, the image will appear reversed.

Front-Ceiling
When selected, the image will turn upside down.
35
English
User Controls

Rear-Ceiling
When selected, the image will appear reversed in upside down
position.
“Screen Type” is for
WXGA only.
Menu Location
Choose the menu location on the display screen.
Screen Type
Choose the screen type from16:10 or 16:9.
Projector ID
ID definition can be set up by menu (range 0~99), and allow user
control an individual projector by RS232. Refer to page 60~63 for
the complete list of RS232 commands.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off.
English
36
User Controls
SETUP
Volume
Press the
Press the
Volume adjustment
can also control MIC
volume.
to decrease the volume.
to increase the volume.
Audio Input
The default audio settings are on the back panel of the
projector. Use this option to reassign any of the Audio Inputs
(1 or 2) to the current image source. Each Audio input can be
assigned to more than one video source.
Audio 1: VGA 1 and VGA 2.
Audio 2: S-Video/Video.
MIC: (No default video source)
RS232
RS232: Allow RS232 control of an individual projector.
(Default setting)
Network: Allow projector control via web browser (Internet
Explorer) using the network.
37
English
User Controls
SETUP | Signal
(RGB)
“Signal” is only
supported in Analog
VGA (RGB) signal.
Automatic
Automatically selects the singal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again.
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or flickers, use this function to
correct it.
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
H. Position
Press the
Press the
to move the image left.
to move the image right.
V. Position
Press the
Press the
English
38
to move the image down.
to move the image up.
User Controls
SETUP | Security
Security
On: Choose “On” to use security verification when the turning
on the projector.
Off: Choose “Off” to be able to switch on the projector without
password verification.
Security Timer

Password default
value is “1234” (first
time).
Use this function to set the how long (Month/Day/Hour) the
projector can be used. Once this time has elapsed you will be
requested to enter your password again.
Change Password
First time:
1. Press “
” to set the password.
2. The password has to be 4 digits.
3. Use number button on the remote to enter your new
password and then press “ ” key to confirm your
password.
Change Password:
1. Press “
” to input old password.
2. Use number button to enter current password and then
press “ ” to confirm.
3. Enter new password (4 digits in length) using the number
buttons on the remote, then press “ ” to confirm.
4. Enter new password again and press “
” to confirm.
39
English
User Controls
If the incorrect password is entered 3 times, the projector will
automatically shut down.
If you have forgotten your password, please contact your local
office for support.
English
40
User Controls
SETUP | Advanced
Logo
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
'XNDQH: The default startup screen.
User: Use stored picture from “Logo Capture” function.
Logo Capture

For successful logo
Press
to capture an image of the picture currently displayed
capture, please
on screen.
ensure that the onscreen image does
not exceed the pro- Closed Captioning
jector’s native resolu- Use this function to set the desired startup screen. If changes are
tion. (XGA:1024x768
made they will take effect the next time the projector is powered
or WXGA:1280x800). on.
Off: select “off” to turn off the closed captioning feature.
CC1:CC1 language: American English.
CC2:CC2 language (depending on the TV channel of the
user):Spanish, French, Portuguese, German, Danish.
41
English
User Controls
SETUP | Network
Network State
Display the network connection status.
DHCP
Use this function to select your desired startup screen. If you
change the setting from one to another, when you exit the OSD
menu, the new setting will take effect on next open.
On: Assign an IP address to the projector from an external
DHCP server automatically.
Off: Assign an IP address manually.
IP Address
Select an IP address.
Subnet Mask
Select subnet mask number.
Gateway
Select the default gateway of the network connected to the
projector.
DNS
Select DNS number.
Apply
Press “
English
42
” and then choose “Yes” to apply the selection.
User Controls
How to use web browser to control your projector
1. Turn on DHCP to allow the DHCP server to automatically assign
an IP, or manually enter the required network information.
2. Then choose apply and press “
configuration process.
” button to complete the
3. Open your web browser and type in from the OSD LAN screen
then the web page will display as below:

When you used
the projector IP
address, you
will can not link
to your service
server.
4. Open “Control Panel” to control your projector.
When making a direct connection from your computer to the
projector
Step 1: Find an IP Address (192.168.6.74) from LAN function of
projector.
43
English
User Controls
Step 2: Select apply and press “Enter” button to submit function or press “menu” key to
exit.
Step 3: To open Network Connections, click Start, click Control Panel, click Network
and Internet Connections, and then click Network Connections. Click the
connection you want to configure, and then, under Network Tasks
, click
Change settings of this connection.
Step 4: On the General tab, under
This connection uses the
following items, click Internet
Protocol (TCP/IP), and then click
“Properties.”
Step 7: The Local Area Network (LAN)
Setting dialog box appears, In the
Proxy Server area, cancel the
Use a proxy server for your LAN
check box., then click “OK” button
twice.
Step 5: Click Use the following IP
address, and type in as below:
1) IP address: 192.168.6.XXX
2) Subnet mask: 255.255.0.0
3) Default gateway:192.168.6.254
Step 8: Open your IE and type in the IP
address of 192.168.6.74 in the
URL then press “Enter” key. The
web page will display as below:
Step 6: To open Internet Options, click
IE web browser, click Internet
Options, click the Connections
tab and click “LAN Settings...”
English
44
Step 9: Open “Control Panel” to control
your projector.
User Controls
Crestron RoomView Control Tool
Crestron RoomView™ provides a central monitoring station for 250+
control systems on a single Ethernet network (more are possible,
the number depends on the combination of IP ID and IP address).
Crestron RoomView monitors each projector, including projector’s
online status, system power, lamp life, network setting and hardware
faults, plus any custom attribute as defined by the Administrator.
The Administrator can add, delete, or edit room information, contact
information and events, which are logged automatically by the
software for all users. (Operation UI as following image)
1. Main Screen
2. Edit Room

Crestron RoomView function support is dependent
on models.
45
English
User Controls
3. Edit Attribute
4. Edit Event
For more information, please visit
http://www.crestron.com & www.crestron.com/getroomview.
English
46
User Controls
OPTIONS
Source Lock
On: The projector will only search current input connection.
Off: The projector will search for other signals if the current

With dust filter
installed, High
Altitude mode must
be turned on. Dust
filter is Optional and
may not be required
in some regions.
input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
Information Hide
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
Keypad Lock

To turn off the keypad lock, press and
hold “Enter” key on
top of the projector
for 5 seconds.
When the keypad lock function is “On”, the control panel will be
locked however, the projector can be operated by the remote
control. By selecting “Off”, you will be able to reuse the control
panel.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
47
English
User Controls
OPTIONS |
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector control panel or on the
remote control.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Sleep Timer (min)

When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
English
48
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Power Mode (Standby)
Eco.: Choose “Eco.” to save power dissipation further < 1W.
Active: Choose “Active” to return to normal standby and the
VGA out port will be enabled.
User Controls
OPTIONS |
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Brightness Mode

When ambient temperature is over 35°C
in operating, the
projector will switch
to STD automatically.
STD: Choose “STD” to dim the projector lamp which will lower
power consumption and extend the lamp life.
BRIGHT: Choose “BRIGHT” to increase the brightness.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
49
English
Appendices
Troubleshooting
If you experience a problem with your projector,
please refer to the following information. If a
problem persists, please contact your local
reseller or service center.
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure all the pins of connectors are not bent or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Ensure that the “AV mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
 Press “Re-SYNC” on the remote.
If you are using a PC:
For Windows 95, 98, 2000, XP, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 × 1200).
6. Select the “Change” button under the “Monitor” tab.
English
50
Appendices
7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Acer  [Fn]+[F5]
Asus  [Fn]+[F8]
Dell  [Fn]+[F8]
Gateway  [Fn]+[F4]
IBM/Lenovo 
HP/Compaq 
NEC 
Toshiba 
[Fn]+[F7]
[Fn]+[F4]
[Fn]+[F3]
[Fn]+[F5]
Mac Apple:
System Preference  Display  Arrangement  Mirror
display
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
displaying your presentation
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.
Image is unstable or flickering
Use “Phase” to correct it. See page 38 for more information.
Change the monitor color setting on your computer.
Image has vertical flickering bar
Use “Frequency” to make an adjustment. See page 38 for more
information.
Check
and re-configure the display mode of your graphic card to

make it compatible with the projector.
51
English
Appendices
Image is out of focus
Make sure the lens cap is removed.
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance.
See page 16.
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image when the projector display mode is set to
16:9 in the OSD.
If you play 4:3 format DVD titles, please change the format to 4:3
in the projector OSD.
If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
Move the projector closer to or further from the screen.
Press “Menu” button on the remote control or projector panel, go
to “DISPLAY  Format” and try the different settings.
Image has slanted sides
Use of Keystone
is not recommended.
If possible, reposition the projector so that it is horizontally
centered on the screen and below the bottom of the screen.
Press
“Keystone +/-” button on the remote control or press

“
/ ” on the projector panel, until the sides are vertical.
Image is reversed
Select “SETUP  Projection” from the OSD and adjust the
projection direction.
English
52
Appendices
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
Check
that “Keypad Lock” is not activated by trying to control the

projector with the remote control.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 55-56.
LED lighting message
Message
Standby State
(Input power cord)
Power on (Warming)
Lamp lighting
Steady light 
No light 
POWER/STANDBY LED
Temp-LED
Lamp-LED
(Green/Amber)
(Red)
(Red)
Amber
Flashing
Green
Green
Power off (Cooling)
Flashing
Green
Error (Over Temp.)
Flashing
Amber
Error (Fan fail)
Flashing
Amber
Error (Lamp fail)
Flashing
Amber
Flashing
* POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.
53
English
Appendices
On Screen Messages
Temperature warning:
Fan failed:
Lamp warning:
Out of display range:
If the remote control does not work
Check the operating angle of the remote control is within ±15°
both horizontally and vertically of one of the IR receivers on the
projector.
Make sure there are not any obstructions between the remote
control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries if they are exhausted.
English
54
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from falling out of projector.”
Warning: Lamp compartment may be hot! Allow it to cool
down before changing the lamp!
Warning: To reduce the risk of personal injury, do not drop
the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
55
English
Appendices
1
The screws on the
lamp cover and the
lamp cannot be
removed.
The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
2
4
3
Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “ ” button.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the two screws on the cover. 1
5. Lift up and remove the cover. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4
To replace the lamp module, reverse the previous steps.
8. Turn on the projector and use “Lamp Reset” after the lamp module is
replaced.
Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select
“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
English
56
Appendices
Compatibility Modes
 Computer Compatibility
Mode
For widescreen
resolution
(WXGA), the
compatibility
support is
dependent on
Notebook/PC
models.
120Hz input
signals may be
dependent on
graphics cards
support.
Please note that
using resolutions
other than native
1024 x 768 (XGA
model), 1280
x 800 (WXGA
model) may result
in some loss of
image clarity.
For WXGA model
only.
Resolution
V-Sync (Hz)
Anglog
Digital
H-Sync (KHz)
Anglog
Digital
VGA
640 × 350
70
70
31.50
31.50
VGA
640 × 350
85
85
37.90
37.90
VGA
640 × 400
85
85
37.90
37.90
VGA
640 × 480
60
60
31.50
31.50
VGA
640 × 480
67
67
-
-
VGA
640 × 480
72
72
37.90
37.90
VGA
640 × 480
75
75
37.50
37.50
VGA
720 × 400
70
70
31.50
31.50
VGA
720 × 400
85
85
37.90
37.90
SVGA
800 × 600
56
56
35.20
35.20
SVGA
800 × 600
60
60
37.90
37.90
SVGA
800 × 600
72
72
48.10
48.10
SVGA
800 × 600
75
75
46.90
46.90
SVGA
800 × 600
120
120
-
-
832 × 624
75
75
-
-
XGA
1024 × 768
60
60
48.40
48.40
XGA
1024 × 768
70
70
56.50
56.50
XGA
1024 × 768
75
75
60.00
60.00
XGA
1024 × 768
120
120
-
-
1152 × 870
75
75
-
-
WXGA
1280 × 800
60
60
49.68
49.64
WSXGA+(*)
1680 × 1050
60
60
65.00
65.00
SXGA
1280 × 1024
60
60
63.98
63.98
UXGA
1600 × 1200
60
60
75.00
75.00
HD
1280 × 720
60
60
45.00
45.00
HD
1280 × 720
120
120
-
-
HD
1920 × 1080
30
30
33.80
33.80
57
English
Appendices
 Computer Compatibility
Mode
Resolution
V-Sync (Hz)
H-Sync (KHz)
MAC LC 13”
640 × 480
66.66
34.98
MAC II 13”
640 × 480
66.68
35.00
MAC 16”
832 × 624
74.55
49.73
MAC 19”
1024 × 768
75
60.24
MAC
1152 × 870
75.06
68.68
MAC G4
640 × 480
60
31.35
i MAC DV
1024 × 768
75
60.00
i MAC DV
1152 × 870
75
68.49
 Video Compatibility
English
58
NTSC
M (3.58MHz), 4.43 MHz
PAL
B, D, G, H, I, M, N
SECAM
B, D, G, K, K1, L
SDTV
480i/p, 576i/p,
HDTV
720p@50Hz/60Hz, 1080i@50Hz/60Hz, 1080p@24Hz/50Hz/60Hz
Appendices
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
1
2
3
RS232 shell is
grounded.
Pin no.
Spec.
(from projector side)
1
TXD
2
RXD
3
GND
59
English
Appendices
RS232 Protocol Function List
XX=00-99, projector's ID,
Baud Rate : 9600
XX=00 is for all projectors
Data Bits: 8
1. There is a <CR> after Parity: None
Optoma
EW610ST/EX610ST
RS232 Command Table.
all ASCII
commands.
Stop
Bits: 1
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Baud Rate : 9600
Note : There is a <CR> after all ASCII commands
Flow
Control : None
0D is the HEX code for <CR> in ASCII code
2.Data
0DBits:
is 8the HEX code
Parity: None
UART16550 FIFO: Disable
forBits:
<CR>
in ASCII
Stop
1
Flow
Control : None
Projector Return (Pass): P
code.
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F
Projector Return (Fail): F
XX=01ˀ99, projector's ID, XX=00 is for all projectors
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX00 1
7E 30 30 30 30 20 31 0D
Power ON
~XX00 0
7E 30 30 30 30 20 30 0D
Power OFF
~XX00 1 ~nnnn
7E 30 30 30 30 20 31 20 a 0D Power ON with Password
~nnnn = ~0000 (a=7E 30 30 30 30) - ~9999(a=7E 39 39 39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX01 1
7E 30 30 30 31 20 31 0D
Resync
~XX02 1
7E 30 30 30 32 20 31 0D
AV Mute
On
~XX02 0
7E 30 30 30 32 20 30 0D
Off
~XX03 1
7E 30 30 30 33 20 31 0D
Mute
On
~XX03 0
7E 30 30 30 33 20 30 0D
Off
~XX04 1
7E 30 30 30 34 20 31 0D
Freeze
~XX04 0
7E 30 30 30 34 20 30 0D
Unfreeze
~XX05 1
7E 30 30 30 35 20 31 0D
Zoom Plus
~XX06 1
7E 30 30 30 36 20 31 0D
Zoom Minus
~XX07 1
7E 30 30 30 37 20 31 0D
Up (Pan under zoom)
~XX08 1
7E 30 30 30 38 20 31 0D
Down (Pan under zoom)
~XX09 1
7E 30 30 30 39 20 31 0D
Left (Pan under zoom)
~XX10 1
7E 30 30 31 30 20 31 0D
Right (Pan under zoom)
~XX12 1
7E 30 30 31 32 20 31 0D
Direct Source Command
HDMI
~XX12 5
7E 30 30 31 32 20 35 0D
VGA 1
~XX12 6
7E 30 30 31 32 20 36 0D
VGA 2
~XX12 9
7E 30 30 31 32 20 39 0D
S-Video
~XX12 10
7E 30 30 31 32 20 31 30 0D
Video
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX20 1
7E 30 30 32 30 20 31 0D
Display Mode
Presentation
~XX20 2
7E 30 30 32 30 20 32 0D
Bright
~XX20 3
7E 30 30 32 30 20 33 0D
Movie
~XX20 4
7E 30 30 32 30 20 34 0D
sRGB
~XX20 5
7E 30 30 32 30 20 35 0D
User
~XX20 7
7E 30 30 32 30 20 37 0D
Blackboard
~XX20 8
7E 30 30 32 30 20 38 0D
Classroom
~XX20 9
7E 30 30 32 30 20 39 0D
3D
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX21 n
7E 30 30 32 31 20 a 0D
Brightness
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX22 n
7E 30 30 32 32 20 a 0D
Contrast
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX23 n
7E 30 30 32 33 20 a 0D
Sharpness
n = 0 (a=30) ~ 31 (a=33 31)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX24 n
7E 30 30 32 34 20 a 0D
Color
Red Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n
7E 30 30 32 35 20 a 0D
Green Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n
7E 30 30 32 36 20 a 0D
Blue Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX27 n
7E 30 30 32 37 20 a 0D
Red Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX28 n
7E 30 30 32 38 20 a 0D
Green Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX29 n
7E 30 30 32 39 20 a 0D
Blue Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX30 n
7E 30 30 33 30 20 a 0D
Cyan
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX31 n
7E 30 30 33 31 20 a 0D
Yellow
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX32 n
7E 30 30 33 32 20 a 0D
Magenta
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1
7E 30 30 33 33 20 31 0D
Reset
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------TM
~XX34 n
7E 30 30 33 34 20 a 0D
BrilliantColor
n = 0 (a=30) ~ 10 (a=31 30)
~XX35 1
7E 30 30 33 35 20 31 0D
Degamma
Film
~XX35 2
7E 30 30 33 35 20 32 0D
Video
~XX35 3
7E 30 30 33 35 20 33 0D
Graphics
~XX35 4
7E 30 30 33 35 20 34 0D
PC
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX36 1
7E 30 30 33 36 20 31 0D
Color Temp.
Warm
~XX36 2
7E 30 30 33 36 20 32 0D
Medium
~XX36 3
7E 30 30 33 36 20 33 0D
Cold
~XX37 1
7E 30 30 33 37 20 31 0D
Color Space
Auto
~XX37 2
7E 30 30 33 37 20 32 0D
RGB
~XX37 3
7E 30 30 33 37 20 33 0D
YUV
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
English
60
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX39 5
7E 30 30 33 39 20 35 0D
Input Source
VGA1
~XX39 6
7E 30 30 33 39 20 35 0D
VGA2
~XX39 9
7E 30 30 33 39 20 39 0D
S-Video
~XX39 10
7E 30 30 33 39 20 31 30 0D
Video
~XX39 1
7E 30 30 33 39 20 31 0D
HDMI
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX195 1
7E 30 30 37 31 20 31 0D
Image AI
On
~XX195 0
7E 30 30 37 31 20 30 0D
Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX44 n
7E 30 30 34 34 20 a 0D
Tint
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX45 n
7E 30 30 34 35 20 a 0D
Color (Saturation)
n = 0 (a=30) ~ 100 (a=31 30 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(WXGA only)
~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9/16:10
~XX60 5
7E 30 30 36 30 20 35 0D
LBX
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
AUTO
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(XGA only)
~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9-I
~XX60 3
7E 30 30 36 30 20 35 0D
16:9-II
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
AUTO
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n
7E 30 30 36 31 20 a 0D
Overscan
n = 0 (a=30) ~ 10(a=31 30)
~XX62 n
7E 30 30 36 32 20 a 0D
Zoom
n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n
7E 30 30 36 33 20 a 0D
H Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX64 n
7E 30 30 36 34 20 a 0D
V Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX66 n
7E 30 30 36 36 20 a 0D
V Keystone
n = -40 (a=2D 34 30) ~ 40 (a=34 30)
~XX69 1
7E 30 30 36 39 20 31 0D
Auto Keystone
On
~XX69 0
7E 30 30 36 39 20 30 0D
Auto Keystone
Off
~XX230 1
7E 30 30 32 33 30 20 31 0D
3D Mode
On
~XX230 0
7E 30 30 32 33 30 20 30 0D
3D Mode
Off
~XX231 1
7E 30 30 32 33 31 20 31 0D
3D Sync Invert
On
~XX231 0
7E 30 30 32 33 31 20 30 0D
3D Sync Invert
Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX70 1
7E 30 30 37 30 20 31 0D
Language
English
~XX70 2
7E 30 30 37 30 20 32 0D
German
~XX70 3
7E 30 30 37 30 20 33 0D
French
~XX70 4
7E 30 30 37 30 20 34 0D
Italian
~XX70 5
7E 30 30 37 30 20 35 0D
Spanish
~XX70 6
7E 30 30 37 30 20 36 0D
Portuguese
~XX70 7
7E 30 30 37 30 20 37 0D
Polish
~XX70 8
7E 30 30 37 30 20 38 0D
Dutch
~XX70 9
7E 30 30 37 30 20 39 0D
Swedish
~XX70 10
7E 30 30 37 30 20 31 30 0D
Norwegian/Danish
~XX70 11
7E 30 30 37 30 20 31 31 0D
Finnish
~XX70 12
7E 30 30 37 30 20 31 32 0D
Greek
~XX70 13
7E 30 30 37 30 20 31 33 0D
Traditional Chinese
~XX70 14
7E 30 30 37 30 20 31 34 0D
Simplified Chinese
~XX70 15
7E 30 30 37 30 20 31 35 0D
Japanese
~XX70 16
7E 30 30 37 30 20 31 36 0D
Korean
~XX70 17
7E 30 30 37 30 20 31 37 0D
Russian
~XX70 18
7E 30 30 37 30 20 31 38 0D
Hungarian
~XX70 19
7E 30 30 37 30 20 31 39 0D
Czechoslovak
~XX70 20
7E 30 30 37 30 20 32 30 0D
Arabic
~XX70 21
7E 30 30 37 30 20 32 31 0D
Thai
~XX70 22
7E 30 30 37 30 20 32 32 0D
Turkish
~XX70 23
7E 30 30 37 30 20 32 33 0D
Farsi
~XX70 25
7E 30 30 37 30 20 32 35 0D
Vietnamese
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX71 1
7E 30 30 37 31 20 31 0D
Projection
Front-Desktop
~XX71 2
7E 30 30 37 31 20 32 0D
Rear-Desktop
~XX71 3
7E 30 30 37 31 20 33 0D
Front-Ceiling
~XX71 4
7E 30 30 37 31 20 34 0D
Rear-Ceiling
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX72 1
7E 30 30 37 32 20 31 0D
Menu Location
Top Left
~XX72 2
7E 30 30 37 32 20 32 0D
Top Right
~XX72 3
7E 30 30 37 32 20 33 0D
Centre
~XX72 4
7E 30 30 37 32 20 34 0D
Bottom Left
~XX72 5
7E 30 30 37 32 20 35 0D
Bottom Right
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(WXGA only)
~XX90 1
7E 30 30 39 31 20 31 0D
Screen Type
16:10
~XX90 0
7E 30 30 39 31 20 30 0D
16:9
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX91 1
7E 30 30 39 31 20 31 0D
Signal
Automatic
On
~XX91 0
7E 30 30 39 31 20 30 0D
Automatic
Off
~XX73 n
7E 30 30 37 33 20 a 0D
Frequency
n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX74 n
7E 30 30 37 34 20 a 0D
Phase
n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n
7E 30 30 37 35 20 a 0D
H. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n
7E 30 30 37 36 20 a 0D
V. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
2
61
English
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX77 n
7E 30 30 37 37 20 aabbcc 0D Security
Security Timer
Month/Day/Hour
n = mm/dd/hh
mm = 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh = 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1
7E 30 30 37 38 20 31 0D
Security
On
~XX78 0
7E 30 30 37 38 20 32 0D
Off
(0/2 for backward compatible)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX79 n
7E 30 30 37 39 20 a 0D
Projector ID
n = 01 (a=30 31) ~ 99 (a=39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX80 1
7E 30 30 38 30 20 31 0D
Mute
On
~XX80 0
7E 30 30 38 30 20 30 0D
Off
~XX81 n
7E 30 30 38 31 20 a 0D
Volume
n = 0 (a=30) ~ 10 (a=31 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX82 1
7E 30 30 38 32 20 31 0D
Logo
Optoma
~XX82 2
7E 30 30 38 32 20 32 0D
User
~XX83 1
7E 30 30 38 33 20 31 0D
Logo Capture
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX88 0
7E 30 30 38 38 20 30 0D
Closed Captioning
Off
~XX88 1
7E 30 30 38 38 20 31 0D
cc1
~XX88 2
7E 30 30 38 38 20 32 0D
cc2
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX100 1
7E 30 30 31 30 30 20 31 0D
Source Lock
On
~XX100 0
7E 30 30 31 30 30 20 30 0D
Off
~XX100 3
7E 30 30 31 30 30 20 33 0D
Next Source
~XX101 1
7E 30 30 31 30 31 20 31 0D
High Altitude
On
~XX101 0
7E 30 30 31 30 31 20 30 0D
Off
~XX102 1
7E 30 30 31 30 32 20 31 0D
Information Hide
On
~XX102 0
7E 30 30 31 30 32 20 30 0D
Off
~XX103 1
7E 30 30 31 30 33 20 31 0D
Keypad Lock
On
~XX103 0
7E 30 30 31 30 33 20 30 0D
Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX104 1
7E 30 30 31 30 34 20 31 0D
Background Color
Blue
~XX104 2
7E 30 30 31 30 34 20 32 0D
Black
~XX104 3
7E 30 30 31 30 34 20 33 0D
Red
~XX104 4
7E 30 30 31 30 34 20 34 0D
Green
~XX104 5
7E 30 30 31 30 34 20 35 0D
White
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX105 1
7E 30 30 31 30 35 20 31 0D
Advanced
Direct Power On
On
~XX105 0
7E 30 30 31 30 35 20 30 0D
Off
~XX106 n
7E 30 30 31 30 36 20 a 0D
Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38 30) , step=5
~XX107 n
7E 30 30 31 30 37 20 a 0D
Sleep Timer (min)
n = 0 (a=30) ~ 995 (a=39 39 35) , step=5
~XX114 1
7E 30 30 31 31 34 20 31 0D
Power Mode(Standby) Eco.(<=1W)
~XX114 0
7E 30 30 31 31 34 20 30 0D
Active
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX109 1
7E 30 30 31 30 39 20 31 0D
Lamp Reminder
On
~XX109 0
7E 30 30 31 30 39 20 30 0D
Off
~XX110 1
7E 30 30 31 31 30 20 31 0D
Brightness Mode
Bright
~XX110 0
7E 30 30 31 31 30 20 30 0D
STD
~XX111 1
7E 30 30 31 31 31 20 31 0D
Lamp Reset
Yes
~XX111 0
7E 30 30 31 31 31 20 30 0D
No
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX112 1
7E 30 30 31 31 32 20 31 0D
Reset
Yes
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX210 n
7E 30 30 32 30 30 20 n 0D
Display message on the OSD
n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to emulate Remote
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 1
7E 30 30 31 34 30 20 31 0D
Power
~XX140 3
7E 30 30 31 34 30 20 33 0D
Mouse Up
~XX140 4
7E 30 30 31 34 30 20 34 0D
Mouse Left
~XX140 5
7E 30 30 31 34 30 20 35 0D
Mouse Enter
~XX140 6
7E 30 30 31 34 30 20 36 0D
Mouse Right
~XX140 7
7E 30 30 31 34 30 20 37 0D
Mouse Down
~XX140 8
7E 30 30 31 34 30 20 38 0D
Mouse Left Click
~XX140 9
7E 30 30 31 34 30 20 39 0D
Mouse Right Click
~XX140 10
7E 30 30 31 34 30 20 31 30 0D
Up/Page +
~XX140 11
7E 30 30 31 34 30 20 31 31 0D
Left/Source
~XX140 12
7E 30 30 31 34 30 20 31 32 0D
Enter (for projection MENU)
~XX140 13
7E 30 30 31 34 30 20 31 33 0D
Right/Re-SYNC
~XX140 14
7E 30 30 31 34 30 20 31 34 0D
Down/Page ~XX140 15
7E 30 30 31 34 30 20 31 35 0D
Keystone +
~XX140 16
7E 30 30 31 34 30 20 31 36 0D
Keystone ~XX140 17
7E 30 30 31 34 30 20 31 37 0D
Volume ~XX140 18
7E 30 30 31 34 30 20 31 38 0D
Volume +
~XX140 19
7E 30 30 31 34 30 20 31 39 0D
Brightness (1)
~XX140 20
7E 30 30 31 34 30 20 32 30 0D
Menu (2)
~XX140 21
7E 30 30 31 34 30 20 32 31 0D
3D(3)
~XX140 22
7E 30 30 31 34 30 20 32 32 0D
HDMI (4)
~XX140 23
7E 30 30 31 34 30 20 32 33 0D
Freeze (5)
~XX140 24
7E 30 30 31 34 30 20 32 34 0D
AV Mute (6)
~XX140 25
7E 30 30 31 34 30 20 32 35 0D
S-Video (7)
~XX140 26
7E 30 30 31 34 30 20 32 36 0D
VGA (8)
~XX140 27
7E 30 30 31 34 30 20 32 37 0D
Video (9)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
English
62
3
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND from projector automatically
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------System status
INFOn
n : 0/1/2/3/4/6/7/8 = Standby/Warming/Cooling/Out of Range/
Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running Out
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------READ from projector
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX121 1
7E 30 30 31 32 31 20 31 0D
Input Source
OKn
n : 0/1/2/3/4/5 = None/VGA1/VGA2/S-Video/Video/HDMI
~XX122 1
7E 30 30 31 32 32 20 31 0D
Software Version
OKdddd
dddd: FW version
~XX123 1
7E 30 30 31 32 33 20 31 0D
Display Mode
OKn
n : 0/1/2/3/4/5/6/7/8 = None/Presentation/Bright/Movie/sRGB/
User/Blackboard/Classroom/3D
~XX124 1
7E 30 30 31 32 34 20 31 0D
Power State
OKn
n : 0/1 = Off/On
~XX125 1
7E 30 30 31 32 35 20 31 0D
Brightness
OKn
~XX126 1
7E 30 30 31 32 36 20 31 0D
Contrast
OKn
~XX127 1
7E 30 30 31 32 37 20 31 0D
Aspect Ratio
OKn
(EW610ST) n: 0/1/2/3/4 = 4:3/16:9 or 16:10 */LBX/Native/AUTO
(EX610ST) n: 0/1/2/3/4 = 4:3/16:9-I/16:9-II/Native/AUTO
*16:9 or 16:10 depend on Screen Type setting
~XX128 1
7E 30 30 31 32 38 20 31 0D
Color Temperature
OKn
n : 0/1/2 = Warm/Medium/Cold
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
OKn
n : 0/1/2/3 = Front-Desktop/Rear-Desktop/Front-Ceiling/Rear-Ceiling
~XX150 1
7E 30 30 31 35 30 20 31 0D
Information
OKabbbbccdddde
a : 0/1 = Off/On
bbbb: Lamp Hour
cc: source 00/01/02/03/04/05=
None/VGA1/VGA2/S-Video/Video/HDMI
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7/8=
None/Presentation/Bright/Movie/sRGB/User/
Blackboard/Classroom/3D
~XX151 1
7E 30 30 31 35 31 20 31 0D
Model name
OKn
n: 6/7/8/9=EW610ST/EX610ST/EW605ST/EX605ST
~XX108 1
7E 30 30 31 30 38 20 31 0D
Lamp Hours
OKbbbb
bbbb: Lamp Hour
~XX108 2
7E 30 30 31 30 38 20 31 0D
Cumulative Lamp Hours
OKbbbbb
bbbbb: (5 digits) Total Lamp Hours
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1RWH'XNDQHSURMHFWRUPRGHOLVSURGXFHGE\2SWRPD7HFKQRORJ\,QF
6LPLODUPRGHOVDUHVROGZRUOGZLGHDQGFRUUHVSRQGWRPRGHOQXPEHU7:67
4
63
English
Appendices
Ceiling Mount Installation
1. To prevent damage to your projector, please use the
'XNDQH ceiling mount.
2. If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector
meet the following specifications:
53.38
306.00
Lens
English
64
110.00
54.64
76.52
82.30
Warning:
1. If you buy a ceiling
mount from another
company, please
be sure to use the
correct screw size.
Screw size will vary
depending on the
thickness of the
mounting plate.
2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the
projector.
3. Avoid installing the
projector near a heat
source.
224.00
Please note that
damage resulting
from incorrect
installation will void
the warranty.
Screw type: M3*3
Maximum screw length: 10mm
Minimum screw length: 7.5mm
59.00
80.48
Unit: mm
Appendices
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this projector.
67
English
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.This device may not cause harmful interference and
2.This device must accept any interference received,
including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canada.
Declaration of Conformity for EU
countries
• EMC Directive 2004/108/EC (including amendments)
• Low Voltage Directive 2006/95/EC
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
English
68
Dukane Audio Visual
2900 Dukane Drive
St. Charles, Illinois 60174
www.dukane.com/audiovisual
Toll Free: 888-245-1966
Fax: 630.584.5156
e-mail: avsales@dukane.com