Dynex DX-WLM 1401-BK/DX-WLM1401-SV/DX-WLM1401

Installing the batteries and removing the nano
receiver
Thank you for purchasing this Dynex Wireless Laptop Mouse.
Package contents
1 Take the battery cover off.
2 Remove the nano receiver.
• Wireless Laptop Mouse with nano receiver
• Quick Setup Guide
System requirements
DX‐WLM1401‐BK / DX‐WLM1401‐SV /
DX‐WLM1401‐BU
Wireless Mouse
Pull
• Windows® 8, Windows® 7, Windows Vista®, or Windows® XP
• One available USB port
Features
ON/OFF switch
Connect
button
Scroll
wheel
Right
button
LED indicator
3 Insert the batteries as shown inside the battery compartment.
4 Replace the cover.
Caution: Insert the battery with the correct orientation, according to
the instruction label on the mouse.
and
Left button
Nano receiver
Battery cover
AAA batteries
Before using your new product, please read these instructions to prevent any damage.
QUICK SETUP GUIDE
Setting up the connection between the receiver and
the mouse
Specifications
Rating: 3V C.C. - 10mA
1 Plug the nano receiver into a USB port on your computer.
Cleaning your mouse
• Wipe the mouse with a damp, lint-free cloth.
Troubleshooting
2 If the mouse does not work, do the following:
Re-plug the nano receiver into the USB port on your computer, then
press the connect button on the mouse. If the mouse does not work
after 10 seconds, pair them again by pressing the connect button on the
mouse. (The nano receiver has auto-pairing function).
3 The LED indicator on the mouse flashes steadily when it is in pairing
mode and stops blinking when it is successfully paired with the nano
receiver.
4 When the battery power gets low, the battery indicator on the mouse
will start to blink.
Mouse indicator
LED indicator
Power ON
LED is on for 10 sec.
Low battery warning
LED blinks for 10 sec.
Pairing
LED blinks.
When paired or
failed after 10 sec.
LED is off.
• Make sure that your computer meets the system requirements.
• Only use the mouse on a clean, flat, non-slippery surface to ensure
smooth and accurate cursor action.
• If your mouse stops working:
• Make sure your mouse and nano receiver are paired by pressing
the connect button on the mouse.
• Replace the mouse batteries.
• Avoid using your mouse on reflective, transparent, or metallic surfaces.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RSS-Gen and RSS-210 statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
RSS-102 statement
This equipment complies with Industry Canada radiation exposure limits set forth for an
uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites
établies pour un environnement non contrôlé.
One-year limited warranty
For complete warranty, visit www.dynexproducts.com.
Legal notices
Contact Dynex
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
For customer service call 1-800-305-2204
www.dynexproducts.com
DYNEX is a registered trademark of BBY Solutions, Inc. Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2013 BBY Solutions, Inc. All Rights Reserved.
V3 ENGLISH 13-0334