User`s guide | Eaton Electrical 1000 Network Card User Manual

Power Xpert ® Gateway Series 1000 Card
User’s Guide
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
S
Harmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 60950 Third Edition
S
EU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
S
EU Standard: EN 55022:1988+A1:2000+A2:2003, Class A/EN55022:1988+A1:2000+A2:2003
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Eaton, Power Xpert, Powerware, and X-Slot are registered trademarks of Eaton Corporation or its subsidiaries and
affiliates. HyperTerminal is a registered trademark of Hilgraeve. Microsoft and Windows are registered trademarks
of Microsoft Corporation. Mozilla and Firefox are registered trademarks of the Mozilla Foundation. Modbus is a
registered trademark of Schneider Electric. OpenView is a trademark of Hewlett-Packard Company. IBM is a
registered trademark of International Business Machines Corporation. Linux is a registered trademark of Linus
Torvalds.
ECopyright 2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Table of Contents
1
2
3
4
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Address Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying IP Addresses (DHCP Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning IP Addresses (DHCP Disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
3
5
8
9
11
16
Configuring the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Changing the Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring SNMP Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Community Strings and Trap Recipients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restricting SNMP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Location and System Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management from an SNMP NMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Modbus TCP/IP Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring E-mail Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring EMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Auto Discovery Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
21
22
22
23
23
24
25
26
28
29
Root Certificate Authority Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
Installing Root CA with Microsoft Internet Explorer 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Root CA with Microsoft Internet Explorer 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Root CA with Mozilla Firefox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
40
42
MIB Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
Eaton PDU MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mainPDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pduPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pduBreaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Eaton EMP MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Eaton Alarms+Traps MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Eaton OID Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entity MIB Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
46
46
46
47
47
47
47
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
i
TABLE OF CONTENTS
5
Modbus Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
Modbus Register Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modbus Function Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PDU/RPP Unit ID Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PDU/RPP Registers and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PDU/RPP Registers (FC 04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PDU/RPP Alarms (FC 02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel Registers and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel Summary Registers (FC 04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel Alarms (FC 01 or 02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breaker Data and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breaker #1 Data Registers (FC 04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calculating Breaker Register Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breaker Alarms (FC 01 or 02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Monitoring Probe (FC 03 or 04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
50
50
51
52
54
54
57
60
60
63
64
64
66
67
68
6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
7
Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
Front-Panel Indicator Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIP Switch Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generating Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading the Card’s Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
73
74
74
Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Two-Year Limited Warranty (US and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
8
ii
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 1
Getting Started
NOTE If you have completed all sections in the Power Xpert Gateway Series 1000 Card
Quick Start Instructions, proceed to Chapter 2, “Configuring the Card,” on page 19.
This section explains:
S Checklist items needed for installation
S Installing the card
S Connecting the card
S Verifying or assigning the IP address
S Configuring the network settings
Installation Checklist
1.
Verify that all of the following items are available:
- Eaton® Power Xpert Gateway (PXGX) Series 1000 Card package
contents (card, configuration cable, Ethernet cable, and quick
start instructions)
- Phillips screwdriver
- Available serial port (RS-232)
- HyperTerminalR (ships with Microsoft® Windows®) or equivalent
terminal emulation application
- Web browser (Internet Explorer or Mozilla® Firefox®
recommended)
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
1
GETTING STARTED
2.
Provide your local network administrator with the card’s MAC
address:
- MAC Address Port 1
_________________________
- MAC Address Port 2
_________________________
The MAC address for Port 1 is located on a label on top of the card.
To determine the MAC address of Port 2, increase the Port 1
address by one. For example: 0060261089A8 (Port 1),
0060261089A9 (Port 2).
3.
Contact the local network administrator for the following network
settings:
- IP Address Port 1 (static address*) _________________________
- IP Address Port 2 (static address*) _________________________
- Gateway Address
_________________________
- Subnet Mask
_________________________
- DNS (name server) IP Address**
_________________________
* The PXGX Series 1000 Card provides two network connections
(Port 1 and Port 2), each accessed with separate IP addresses. If
you are setting up the PXGX Series 1000 Card in a dynamic host
configuration protocol (DHCP) environment (default), the network
administrator must set up the DHCP server to provide a static
address each time the card makes a DHCP request. Use Port 2 only
if you need a redundant connection using a separate subnet.
** Obtain the Domain Name Server (DNS) IP address if you plan to
use host names.
4.
If you need e-mail functionality, obtain the SMTP IP address or host
name. If using the SMTP host name, verify that you also have the
DNS IP address (see Step 3).
- SMTP (mail server) IP Address or
Host Name
2
_________________________
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
Installing the Card
The hot-swappable PXGX Series 1000 Card can be installed without
turning off the Powerware® Power Distribution Unit (PDU) or
disconnecting the load.
To install the PXGX Series 1000 Card:
1.
Verify that all six DIP switches on the card are in the off position
(see Figure 1).
OFF
ON
Figure 1. Verify DIP Switches are OFF
2.
Remove the X-Slot® cover from the PDU. Retain the screws.
NOTE If there is another card already installed with an attached communication cable,
disconnect the cable and then remove the card.
3.
If not already done, record the MAC address for Port 1 and Port 2,
for future reference (see “Installation Checklist” on page 1).
4.
To prevent electrostatic discharge (ESD), place one hand on a metal
surface such as the PDU panel.
5.
Slide the card into the open slot and secure with the screws
removed in Step 2 (see Figure 2 and Figure 3).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
3
GETTING STARTED
Figure 2. Install the PXGX Series 1000 Card
6.
Connect an active Ethernet cable (supplied) to the Port 1 Ethernet
connector on the PXGX Series 1000 Card (see Figure 3).
If you are connecting a second network connection (separate
subnet), connect an active Ethernet cable (not supplied) to the
Port 2 Ethernet connector on the PXGX Series 1000 Card.
Figure 3. Secure the Card and Install the Ethernet Cable
7.
4
If you know the card’s IP address, continue to “Network
Configuration” on page 16; otherwise, continue to the following
section, “Connecting the Card.”
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
Connecting the Card
To connect the card to the computer and start the configuration:
1.
Plug the RJ-45 end of the supplied configuration cable into the
configuration port on the card labeled “10101” (see Figure 4).
NOTE Verify that you have used the port labeled “10101.” The other ports on the card do
not work for configuration.
Figure 4. Install Configuration Cable
2.
Plug the other end of the serial cable into the serial COM port on
the computer.
3.
Open your terminal emulation program (such as HyperTerminal).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
5
GETTING STARTED
4.
Select the serial connection (such as COM1). See Figure 5.
Figure 5. Select Serial Connection
5.
Set the serial line to 9600 baud, No parity, 8 data bits, 1 stop bit,
and no flow control (see Figure 6).
Figure 6. Configure Port Settings
6
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
6.
Verify that the PDU is turned on.
7.
After a few seconds, press Enter. The Network Settings menu
appears in approximately one minute (see Figure 7).
------------------------------------------------------------------------ Network Settings -----------------------------------------------------------------------1. Ethernet Port 1 Settings
2. Ethernet Port 2 Settings
3. DNS Server (Primary)
: [None]
4. DNS Server (Secondary) : [None]
5. Reset to Factory Defaults and Exit
0. Exit
Select an option ==> 1
Figure 7. Network Settings Menu
If the menu does not appear, press Enter again. If it still does not
appear, check the following conditions:
S Verify the serial line is set to 9600 baud, No parity, 8 data bits,
1 stop bit, and no flow control.
S If the serial line settings are correct, check the cabling to verify
all connections are secure.
S Verify that your terminal program is on the correct
communication port for the serial connection.
S Verify that the card has power (one or more LEDs on the card
are illuminated). The PDU should be on.
8.
Continue to the following section, “IP Address Assignments.”
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
7
GETTING STARTED
IP Address Assignments
Many IT managers prefer the convenience of DHCP for managing the IP
addresses of networked devices. With DHCP, the IT managers can
easily reassign IP addresses as the network structure changes. In some
cases, DHCP may not be available, or fixed IP addresses may be
preferred for the PXGX Series 1000 Card (for example, if some other
networked device needs to reach the card at a fixed address).
To verify the IP addresses assigned through DHCP, continue to
“Verifying IP Addresses (DHCP enabled).” To manually enter fixed IP
addresses for the card’s network connection, continue to “Assigning IP
Addresses (DHCP disabled),” on page 11.
NOTE By default, the PXGX Series 1000 Card requests an IP address via DHCP when
connected to a network.
8
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
Verifying IP Addresses (DHCP Enabled)
To verify the IP address assignments:
1.
Type 1 and press Enter on the Network Settings menu (see Figure 7
on page 7) to display the Network Settings: Ethernet Port 1 menu
(see Figure 8).
-------------------------------------------------------------- Network Settings: Ethernet Port 1 -------------------------------------------------------------1. Dynamic Addressing (DHCP) Enabled
2. IP Address
10.222.51.250
3. Subnet Mask
255.255.255.0
4. Default Gateway
10.222.51.254
MAC Address
Link Status
00:60:26:10:89:A8
Enabled
0. Exit to previous menu
Select an option ==>
Figure 8. Ethernet Port 1 Menu
2.
Verify and record the IP address for Port 1*.
3.
Type 0 and press Enter to return to the Network Settings menu.
4.
If you connected Ethernet Port 2 to a separate network, continue to
Step 5 to verify the assigned IP address. Otherwise, continue to
Step 8.
5.
Type 2 and press Enter on the Network Settings menu to display the
Network Settings: Ethernet Port 2 menu.
6.
Verify and record the IP address for Port 2*.
7.
Type 0 and press Enter to return to the Network Settings menu.
8.
Type 0 and press Enter to exit the utility.
* If the IP address field contains [None], press Enter to return to the Network Settings menu and wait 60 seconds.
Repeat Steps 1 through 8. If the field remains [None], contact your local network administrator to verify that the
DHCP server is responding to requests.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
9
GETTING STARTED
9.
Verify network communication by using a Web browser (see
Figure 9). Type the IP address of the card and select Go.
10. The login prompt appears. The user name and default password is
user for read-only information and admin for configuration
(read/write) options.
The PXGX Series 1000 Card Web page opens (see Figure 9).
Enter the Card’s IP Address
Figure 9. PXGX Series 1000 Card Web Page
11. If you logged in as admin, continue to Chapter 2, “Configuring the
Card” on page 19 for additional configuration options.
NOTE Once you have logged in as admin, it is important to completely exit the browser to
set the security level back to the standard read-only level.
10
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
Assigning IP Addresses (DHCP Disabled)
NOTE You can also set network settings via the PXGX Series 1000 Card’s Web page
Network link (see “Network Configuration” on page 16).
To manually enter fixed IP addresses for the card after you have
connected it:
1.
Type 1 and press Enter on the Network Settings menu (see
Figure 10) to display the Network Settings: Ethernet Port 1 menu
(see Figure 11).
------------------------------------------------------------------------ Network Settings -----------------------------------------------------------------------1. Ethernet Port 1 Settings
2. Ethernet Port 2 Settings
3. DNS Server (Primary)
: [None]
4. DNS Server (Secondary) : [None]
5. Reset to Factory Defaults and Exit
0. Exit
Select an option ==> 1
Figure 10. Network Settings Menu
-------------------------------------------------------------- Network Settings: Ethernet Port 1 -------------------------------------------------------------1. Dynamic Addressing (DHCP) Enabled
2. IP Address
[None]
3. Subnet Mask
[None]
4. Default Gateway
[None]
MAC Address
Link Status
00:60:26:10:89:A8
Enabled
0. Exit to previous menu
Select an option ==>
Figure 11. Ethernet Port 1 Menu
2.
Type 1 and press Enter to display the DHCP control option (see
Figure 12).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
11
GETTING STARTED
-------------------------------------------------------------- Network Settings: Ethernet Port 1 -------------------------------------------------------------1. Dynamic Addressing (DHCP) Disabled
2. IP Address
[None]
3. Subnet Mask
[None]
4. Default Gateway
[None]
MAC Address
Link Status
00:60:26:10:89:A8
Enabled
0. Exit to previous menu
Select an option ==> 1
Enable DHCP? (y/n): n
Figure 12. DHCP Control Option
3.
Type n and press Enter to disable DHCP control.
4.
To set the IP address, type 2 and press Enter. Type the IP address
and press Enter.
5.
To set the subnet mask, type 3 and press Enter. Type the subnet
mask address and press Enter.
6.
To set the gateway, type 4 and press Enter. Type the gateway
address and press Enter.
7.
Type 0 to return to the Network Settings menu (see Figure 13).
------------------------------------------------------------------------ Network Settings -----------------------------------------------------------------------1. Ethernet Port 1 Settings
2. Ethernet Port 2 Settings
3. DNS Server (Primary)
: [None]
4. DNS Server (Secondary) : [None]
5. Reset to Factory Defaults and Exit
6. Save & apply all settings
0. Exit without saving
Select an option ==>
Figure 13. Network Settings Menu
8.
12
If you connected Ethernet Port 2 to a separate network, continue to
Step 9 to assign the IP address for Port 2. Otherwise, continue to
Step 11.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
9.
Type 2 and press Enter on the Network Settings menu (see
Figure 10 on page 11) to display the Network Settings: Ethernet
Port 2 menu (see Figure 14).
--------------------------------------------------------------- Network Settings: Ethernet Port 2 --------------------------------------------------------------1. Dynamic Addressing (DHCP) Enabled
2. IP Address
[None]
3. Subnet Mask
[None]
4. Default Gateway
[None]
MAC Address
Link Status
00:60:26:10:89:A8
Enabled
0. Exit to previous menu
Select an option ==>
Figure 14. Ethernet Port 2 Menu
10. Repeat Steps 2 through 7 to assign the IP address and other
options for Port 2.
11. If you will be using host names for controlling access to the card,
type 3 and press Enter. Type the primary DNS server IP address and
press Enter.
Type 4 and press Enter. Type the secondary DNS server IP address
and press Enter (see Figure 15).
------------------------------------------------------------------------ Network Settings -----------------------------------------------------------------------1. Ethernet Port 1 Settings
2. Ethernet Port 2 Settings
3. DNS Server (Primary)
: 10.222.51.8
4. DNS Server (Secondary) : [None]
5. Reset to Factory Defaults and Exit
6. Save & apply all settings
0. Exit without saving
Select an option ==> 4
Figure 15. DNS Server Settings
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
13
GETTING STARTED
12. Type 6 and press Enter to save and apply all settings (see Figure 16).
13. Type y and press Enter to confirm that you want to save and apply
all settings and exit the utility.
------------------------------------------------------------------------ Network Settings -----------------------------------------------------------------------1. Ethernet Port 1 Settings
2. Ethernet Port 2 Settings
3. DNS Server (Primary)
: 10.222.51.8
4. DNS Server (Secondary) : 10.222.1.75
5. Reset to Factory Defaults and Exit
6. Save & apply all settings
0. Exit without saving
Select an option ==> 6
Save & apply all settings? (y/n): y
Figure 16. Save and Apply All Settings
14
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
14. Verify network communication by using a Web browser (see
Figure 17). Type the IP address of the card and select Go.
15. The login prompt appears. The user name and default password is
user for read-only information and admin for configuration
(read/write) options.
The PXGX Series 1000 Card Web page opens (see Figure 17).
Enter the Card’s IP Address
Figure 17. PXGX Series 1000 Card Web Page
16. If you logged in as admin, continue to Chapter 2, “Configuring the
Card” on page 19 for additional configuration options.
NOTE Once you have logged in as admin, it is important to completely exit the browser to
set the security level back to the standard read-only level.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
15
GETTING STARTED
Network Configuration
If you know the card’s IP address, you can configure the network
settings from the card’s Web page:
1.
Open a Web browser, type the IP address of the card, and select
Go.
2.
The login prompt appears. The user name and default password is
user for read-only information and admin for configuration
(read/write) options. Log in as admin.
The PXGX Series 1000 Card Web page opens (see Figure 18).
Enter the Card’s IP Address
Figure 18. PXGX Series 1000 Card Web Page
3.
Select the Network link from the menu bar.
The Network Configuration Settings page appears. The page shows
the current network status for each port on the card (green
indicates the network is connected; red indicates the network is
disconnected).
4.
16
You can enable or disable the DHCP control by activating or
deactivating the check box. The default is DHCP enabled.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
GETTING STARTED
5.
If you will be using host names for controlling access to the card,
enter the Domain, as well as the DNS IP addresses in the
Nameserver fields.
6.
If you will be using Simple Network Management Protocol (SNMP),
identify the physical location of the installed PDU/card (sysLocation
string) in the System location field. This value also appears in the
card’s Web page header bar.
Enter the information to identify someone to contact with questions
about this device (sysContact string) in the System contact field. For
example, you can type a person’s name, phone number,
department, e-mail address, or physical location.
7.
You can also modify the card’s IP address, the subnet mask, and
the gateway address for Port 1 and Port 2 (IP address, Netmask, and
Gateway fields).
8.
Click Apply to save the settings or Discard to cancel the changes.
9.
Continue to Chapter 2, “Configuring the Card” on page 19 for
additional configuration options.
NOTE Once you have logged in as admin, it is important to completely exit the browser to
set the security level back to the standard read-only level.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
17
GETTING STARTED
18
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 2
Configuring the Card
NOTE If DHCP is disabled and you will be using host names for servers, such as the mail
server, Network Time Protocol (NTP) server, SNMP hosts, Modbus®/TCP hosts, or trap
recipients, enter the IP address of your network DNS Server (see “Network Configuration” on
page 16).
NOTE You must be logged in as admin to configure the card. Once you have logged in as
admin, it is important to completely exit the browser to set the security level back to the
standard read-only level.
This section explains:
S Changing the passwords
S Setting the date and time
S Configuring SNMP options and managing from an SNMP NMS
S Configuring Modbus TCP/IP options
S Configuring e-mail notification
S Configuring the Powerware Environmental Monitoring Probe (EMP)
S Configuring auto discovery settings
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
19
CONFIGURING THE CARD
Changing the Passwords
The user name and default password is user for read-only information
and admin for configuration (read/write) options.
To change the passwords:
1.
From the card’s Web page, click the Access Control link from the
menu bar.
2.
To change the user password, enter the new password in the ’user’
password field. The characters appear as asterisks (*).
To change the admin password, log in as admin and enter the new
password in the ’admin’ password field. The characters appear as
asterisks (*).
3.
Click Apply and then OK to save the settings. The password updates
and displays as a full row of asterisks.
NOTE Once you have logged in as admin, it is important to completely exit the browser to
set the security level back to the standard read-only level.
NOTE After you change the password, you will be prompted to enter the new password
the next time you navigate through the card’s Web page.
20
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
CONFIGURING THE CARD
Setting the Date and Time
NOTE All selections are automatically converted to Coordinated Universal Time (UTC).
To set the date and time:
1.
From the card’s Web page, click the Date/Time link from the menu
bar.
The default is to synchronize the date and time from the PC clock.
2.
To synchronize the card with Network Time Protocol servers, select
Synchronize with NTP server(s) and type the IP addresses or host
names. You can synchronize the card with up to three NTP servers.
The NTP status is indicated in parentheses:
S Not running – Indicates that NTP is not running.
S Started, not synchronized – Indicates that NTP is running, but is not
yet synchronized with an NTP server or controlling the local
clock.
S Synchronizing with NTP server – Indicates that NTP has
synchronized with the local clock, but is not yet synchronized
with an NTP server.
S Synchronized to XX, NTP stratum YY – Indicates that the card is
synchronized with an NTP server at IP address XX that is
operating at NTP Stratum YY.
NOTE When using host names, verify that the IP address of your network DNS Server is
configured (see “Network Configuration” on page 16).
NOTE When NTP status is Synchronized and there is a large discrepancy between the
PXGX Series 1000 Card time and the actual time, it may take 5–30 minutes for NTP to reset
the card to the proper time.
3.
To set the time manually, select Set date/time manually and use the
pull-down menus to select the local date in mm/dd/yyyy format and
the local time in hh/mm/ss format.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
21
CONFIGURING THE CARD
4.
To customize how the date appears in the card’s data and event
logs, select a Date format for logs option (mm/dd/yyyy, dd/mm/yyyy,
yyyy-mm-dd, or dd mmm yyyy). The default is mm/dd/yyyy.
5.
To select the time zone for the card, specify the Timezone for Logs,
email, and connected device.
6.
Click Apply and then OK to save the settings.
Configuring SNMP Options
This section describes the following SNMP configuration options:
S Configuring community strings and trap recipients
S Restricting SNMP access
S Setting system location and system contact
S Managing from an SNMP NMS
Community Strings and Trap Recipients
The default community strings are “public” for read-only, “private” for
read-write, and “public” for receiving traps.
The PXGX Series 1000 Card supports several event-related traps that
can be reported to the SNMP network management software. See
Chapter 4, “MIB Files,” on page 45 for more information.
To configure the SNMP options:
1.
From the card’s Web page, click the SNMP link from the menu bar.
2.
To change the community strings, type a new community string in
the appropriate field.
3.
Click Add to add a new trap recipient entry to the list. An
IP/hostname field appears. Enter the IP address or host name for
the trap recipient.
NOTE When using host names, verify that the IP address of your network DNS Server is
configured (see “Network Configuration” on page 16).
22
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
CONFIGURING THE CARD
4.
Click Apply and then OK to save the settings.
5.
Repeat Steps 3 and 4 for each additional trap recipient.
To remove a trap recipient, click Delete Last. Click OK when
prompted to remove the settings for the trap recipient entered last.
Restricting SNMP Access
To limit access to the card from trusted SNMP NMS hosts only:
1.
From the card’s Web page, click the Access Control link from the
menu bar.
2.
Activate the check box for SNMP access restricted by IP/hostname.
3.
Type the trusted NMS host’s IP addresses or host names,
separated by a semi-colon, in the Trusted IPs/hostnames field.
NOTE When using host names, verify that the IP address of your network DNS Server is
configured (see “Network Configuration” on page 16).
4.
Click Apply and then OK to save the settings.
System Location and System Contact
To set the system location and system contact:
1.
From the card’s Web page, click the Network link from the menu
bar.
2.
Enter the physical location of the installed Power Distribution Unit
(PDU)/card (sysLocation string) in the System location field. This
value also appears in the card’s Web page header bar.
3.
Enter the information to identify someone to contact with questions
about this device (sysContact string) in the System contact field. For
example, you can type a person’s name, phone number,
department, e-mail address, physical location, or combination of
these items, such as “John Smith x123”.
4.
Click Apply and then OK to save the settings.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
23
CONFIGURING THE CARD
Management from an SNMP NMS
To access the PXGX Series 1000 Card via SNMP:
1.
Use these default Community strings:
GET Community string: public
SET Community string: private
2.
From the card’s Web page, click the Documentation link from the
menu bar (or visit www.eaton.com/powerxpert) for the following
MIB files for the PXGX Series 1000 Card:
MIB Name
Filename
Description
Eaton PDU MIB
EATON-PDU-MIB.txt
Meters available from the PDU, including
identification, input, output, configuration,
tests, alarms, bypass, traps, panel data, and
circuit breaker data
Eaton EMP MIB
EATON-EMP-MIB.txt
Meters and settings for the EMP
Eaton Alarms+Traps MIB
EATON-PXG-MIB.txt
Alarms and notifications (traps)
Eaton Object Identifier (OID)
assignments
EATON-OIDS.txt
Base document for all OID assignments for
Eatons MIBs
RFC 4133 Entity MIB
ENTITY-MIB.txt
Identification and description of each device
attached to the card
RFC 4268 Entity State MIB
ENTITY-STATE-MIB.txt
Five availability status meters for each
device attached to the card
RFC 4268 Entity State MIB, part 2
ENTITY-STATE-TC-MIB.txt
Possible state values for the Entity State MIB
Add these files to the MIB database of your SNMP management
software (such as HP OpenViewt
, IBMR Director, and Sun
NetManager).
3.
24
Use the facilities provided by the SNMP management software to
access the individual MIB objects. See Chapter 4, “MIB Files,” on
page 45 for more information.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
CONFIGURING THE CARD
Configuring Modbus TCP/IP Options
To limit access to the card from trusted Modbus TCP/IP addresses only:
1.
From the card’s Web page, click the Access Control link from the
menu bar.
2.
Activate the check box for Modbus-TCP access restricted by
IP/hostname.
3.
Type the trusted host’s IP addresses or host names, separated by a
semi-colon, in the Trusted IPs/hostnames field.
NOTE When using host names, verify that the IP address of your network DNS Server is
configured (see “Network Configuration” on page 16).
NOTE If the SMTP server does not use Port 25, append the port to the IP address (for
example, mysmtpserver:33).
4.
Click Apply and then OK to save the settings.
For information on Modbus registers, see Chapter 5, “Modbus
Registers,” on page 49.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
25
CONFIGURING THE CARD
Configuring E-mail Notification
You may use the PXGX Series 1000 Card to inform selected e-mail
accounts of events and changes in status as they occur in the PDU or to
provide a status message at a predetermined time.
To configure e-mail notification:
1.
From the card’s Web page, click the Email link from the menu bar.
2.
Enter the IP address or host name of the SMTP Server IP/hostname
(mail server) that will be used to send the e-mail messages.
3.
If you need to enter a user name and password for the SMTP
server, click Advanced SMTP settings....
If you have made changes to the E-mail page, click OK to save the
settings; otherwise, click Cancel. The Advanced SMTP
Configuration Settings page appears.
Enter the user name and password in the SMTP username and SMTP
password fields.
You can specify a “from” e-mail address in the SMTP “From” Address
field (for example, PDU_1@10.222.10.111).
Click Apply to save the settings and return to the previous screen.
4.
You can specify events to trigger an e-mail to be sent to all
recipients. Click Configure to select the events.
Click OK to save the settings; otherwise, click Cancel. The Email
Event Trigger Configuration Settings page appears.
You can select all, deselect all, or select specific event check boxes
for e-mail notification.
Click Apply to save the settings and return to the previous screen.
Test the event e-mail function by selecting Test Event Email. A
sample e-mail is sent for the first trigger event that is selected and
saved.
26
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
CONFIGURING THE CARD
5.
The e-mail Recipients are numbered. Select a number for a recipient.
You can select different options for each recipient (Steps 6
through 10).
After you enter and save an e-mail address, the Recipients list
updates to show the recipient number and the corresponding e-mail
address.
6.
The default (True) is to send an e-mail when an event is activated
and when it clears. Select False in the appropriate Send on event...
fields to change these notification settings.
7.
The default (True) is to attach an event log file, a data log file, and a
PDU identification file to the Event e-mails. (These files are always
attached to the Daily e-mails.) Select False in the appropriate
Attach... fields to remove these attachments from the Event e-mails.
8.
The default (True) is to send a daily status report. Select False in the
Send periodic status field to cancel the status e-mails, or change the
number of Days between periodic status email to receive them less
frequently.
9.
Specify the Time of day to send the e-mail (in 24-hour format, PXGX
Series 1000 Card time).
10. Enter the recipient’s e-mail address in the To field.
11. Click Apply to save the e-mail settings.
12. Select the next number in the Recipients pull-down menu to add
another e-mail recipient.
Repeat Steps 6 through 11 for each additional e-mail recipient.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
27
CONFIGURING THE CARD
Configuring EMP Settings
NOTE Verify that the Power Xpert Gateway Card DIP switch #2 is set to the ON position,
enabling the card for communication with an EMP.
To configure the EMP settings:
28
1.
From the card’s Web page, click the Environmental Monitoring Probe
link from the menu bar.
2.
For Contact #1 and #2, enter the Contact Description, such as
External Contact #1 and External Contact #2.
3.
For Contact #1 and #2, select the Contact Type as Normally Open or
Normally Closed from the pull-down menu. Disabled is the default.
4.
To set the temperature limits of the EMP, enter 0 to 70 degrees
Celsius for the Temperature Upper Limit and the Temperature Lower
Limit. The default for the upper limit is 70; the default for the lower
limit is 0.
5.
Use the Temperature Hysteresis to control the alarm when the
current value is hovering around the limit. When the EMP
temperature measure activates the alarm, it can come out of the
alarm state only by dropping below the Temperature Hysteresis
value. Enter a value between 0 and 10 percent. The default is
2 percent.
6.
To set the humidity limits of the EMP, enter 0 to 90 percent for the
Humidity Upper Limit and the Humidity Lower Limit. The default for the
upper limit is 90; the default for the lower limit is 0.
7.
Use the Humidity Hysteresis to control the alarm when the current
value is hovering around the limit. When the EMP humidity
measure activates the alarm, it can come out of the alarm state only
by dropping below the Humidity Hysteresis value. Enter a value
between 0 and 20 percent. The default is 2 percent.
8.
Click Apply to save the settings.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
CONFIGURING THE CARD
Configuring Auto Discovery Settings
Configure the Auto Discovery settings so that the Power Xpert Software
can find the PXGX Series 1000 Card on the network automatically. The
card sends multicast discovery messages to any control Power Xpert
host monitoring the specified Listen port.
To configure the auto discovery settings:
1.
From the card’s Web page, click the Auto Discovery link from the
menu bar.
2.
The default Listen port is 1900. To modify, enter a value between
10000 and 65535.
3.
The default Announce period is 600 seconds. To modify, enter a
value between 60 and 1800 seconds.
4.
The default Announce TTL is 4 hops. To modify, enter a value
between 1 and 254.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
29
CONFIGURING THE CARD
30
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 3
Root Certificate Authority Installation
Improve the security of your PXGX Series 1000 Card on the Web by
installing a root certificate authority (CA). A CA is a trusted third-party
organization that issues digital certificates for use with encrypted digital
transactions. The digital certificate guarantees that the company holding
a certificate is who it claims to be.
You can use the card without installing a root CA (using http), but the
transactions will not be as secure as with the root CA (using https). The
performance of the card is not impacted by using secure transactions.
This section explains root CA installation for:
S Microsoft Internet Explorer 6
S Microsoft Internet Explorer 7
S Mozilla Firefox
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
31
ROOT CERTIFICATE AUTHORITY INSTALLATION
Installing Root CA with Microsoft Internet Explorer 6
To install a certificate for the PXGX Series 1000 Card with Microsoft
Internet Explorer 6:
1.
Open the browser, type the IP address of the card in the address
bar, and select Go. For example: https://10.222.51.236/
The Security Alert window opens (see Figure 19).
Figure 19. Security Alert Window
32
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
2.
Click the View Certificate button.
The Certificate window opens (see Figure 20).
Figure 20. Certificate Window
NOTE The certificate cannot be verified yet because it is issued by a nontrusted CA.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
33
ROOT CERTIFICATE AUTHORITY INSTALLATION
3.
Select the Certification Path tab.
The root CA is displayed as “Power Xpert Gateway Card” and the
issued certificate is shown as the device’s IP address (see
Figure 21).
4.
Select Power Xpert Gateway Card.
Figure 21. Certification Path Window
34
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
5.
Click View Certificate.
A new Certificate window opens for the CA (see Figure 22).
Figure 22. Certification Window for the Power Xpert Gateway Card
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
35
ROOT CERTIFICATE AUTHORITY INSTALLATION
6.
Click Install Certificate....
The Certificate Import Wizard window opens (see Figure 23).
Figure 23. Certificate Import Wizard
36
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
7.
Click Next.
The Certificate Store window opens, prompting you to specify a
certificate store (see Figure 24).
Figure 24. Certificate Store Window
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
37
ROOT CERTIFICATE AUTHORITY INSTALLATION
8.
Verify that the default setting, Automatically select the certificate
store ..., is selected.
9.
Click Next.
The certificate wizard displays a final verification (see Figure 25).
Figure 25. Verifying the Certificate Import Settings
10. Click Finish to complete the wizard.
A message box similar to Figure 26 opens:
Figure 26. Security Warning Message
38
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
11. Click Yes to install the CA.
A new dialog box window opens to verify that the import was
successful.
12. Close all windows except for the original Security Alert window
(see Figure 19 on page 32).
13. Click View Certificate.
An updated Certificate window opens showing a trusted certificate
(see Figure 27).
14. Click OK.
Figure 27. Updated Certificate Window
15. The installation process is complete. You can now access the card
using the https protocol (for example, https://10.222.51.236).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
39
ROOT CERTIFICATE AUTHORITY INSTALLATION
Installing Root CA with Microsoft Internet Explorer 7
To install a certificate for the PXGX Series 1000 Card with Microsoft
Internet Explorer 7:
1.
Open the browser and type the IP address of the card followed by
the path “/ca.html” in the address bar. For example:
http://10.222.51.236/ca.html
The following window displays (see Figure 28):
Figure 28. Internet Explorer 7 Window
40
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
2.
Click Root CA Certificate.
A File Download warning window opens (see Figure 29).
Figure 29. File Download Warning
3.
Click Open.
The Certificate Window opens (see Figure 20 on page 33).
4.
Follow the remaining steps for using Internet Explorer 6 (Step 3 on
page 34 through Step 15 on page 39).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
41
ROOT CERTIFICATE AUTHORITY INSTALLATION
Installing Root CA with Mozilla Firefox
To install a certificate for the PXGX Series 1000 Card with Mozilla
Firefox:
1.
Open the browser and type the IP address of the card followed by
the path “/ca.html” in the address bar. For example:
http://10.222.51.236/ca.html
The following window displays (see Figure 30):
Figure 30. Mozilla Firefox Window
42
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
ROOT CERTIFICATE AUTHORITY INSTALLATION
2.
Click Root CA Certificate.
Firefox opens the Downloading Certificate window (see Figure 31).
Figure 31. Downloading Certificate Window
3.
If desired, click View to manually examine the contents of the
certificate.
4.
Click the Trust this CA to identify web sites check box option.
5.
Click OK to complete the installation process.
The installation process is complete. You can now access the card
using the https protocol (for example, https://10.222.51.236).
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
43
ROOT CERTIFICATE AUTHORITY INSTALLATION
44
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 4
MIB Files
This chapter describes the Management Information Base (MIB) files
available with the card. A MIB is an information repository residing on a
device in a communication network. Network management software
uses a device’s MIB to manage the device. Every manageable device on
a network has a MIB consisting of one or more files that list information
about the device.
Use the facilities provided by your Simple Network Management
Protocol (SNMP) management software to access the individual MIB
objects. The objects define the information available about your Power
Distribution Unit (PDU) or Remote Power Panel (RPP).
You can configure a device so that it generates a trap if a certain
condition occurs, such as an alarm clearing. The trap is sent to the
management station to inform it of the occurrence.
This chapter contains an overview of MIB definitions for each of the MIB
files:
S Eaton PDU MIB
S Eaton EMP MIB
S Eaton Alarms+Traps MIB
S Eaton OID Assignments
S RFC 4133 Entity MIB
S RFC 4268 Entity State MIB
S RFC 4268 Entity State MIB, part 2
See the MIB files for detailed information about each MIB object.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
45
MIB FILES
Eaton PDU MIB
The Eaton PDU MIB module contains objects and notifications for PDU,
Panel, and Breaker information levels:
S mainPDU
S pduPanel
S pduBreaker
mainPDU
Objects in this group describe the main PDU in the system. This group
has three subgroups:
S Nameplate Ratings subgroup. These objects provide the nominal
rating values for the PDU.
S Input Meters subgroup. These objects provide input meter values for
the PDU. The subgroup contains a table of meters by phase (normally
three-phase)
S Output Meters subgroup. These objects provide output meter values
for the PDU. The subgroup contains a table of meters by phase
(normally three-phase)
pduPanel
Objects in this group provide the nominal values for each panel. The
group contains a table of meters by phase (normally three-phase) and
tables of meters and ratings that are not dependent on an individual
phase.
pduBreaker
Objects in this group provide the nominal values for each breaker. The
group contains a table of meters by phase (normally three-phase) and
tables of meters and ratings that are not dependent on an individual
phase.
46
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MIB FILES
Eaton EMP MIB
Objects in this group are provided by the EMP and include temperature
and humidity readings, alarming limits, the two contacts readings, and
setup information. The group contains a table of values for
environmental contact sensing (normally two digital inputs for
monitoring all contacts).
Traps are sent in response to EMP changes to indicate the type of
alarm, alarm acknowledgement, and alarm clearing.
Eaton Alarms+Traps MIB
Objects in this group provide a table of active alarms and a count of
alarms currently active. The notification traps provided are triggered by
the publishing of an alarm or event.
Eaton OID Assignments
These objects document all the object identifier assignments for Eaton
products.
Entity MIB Files
The objects in these MIB files provide information standard in the
industry:
S The RFC 4133 Entity MIB provides standard objects for identifying
and describing devices attached to the card.
S The RFC 4268 Entity State MIB provides availability status measures
for each device.
S The RFC 4268 Entity State MIB Part 2 provides possible state values
for the Entity State MIB.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
47
MIB FILES
48
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 5
Modbus Registers
This chapter describes how to address a specific Power Distribution Unit
(PDU) or Remote Power Panel (RPP), a specific panel in a PDU or RPP,
and a specific breaker in a panel using Modbus TCP/IP.
NOTE To obtain the panel or circuit breaker data, the PDU/RPP must have the Energy
Management System (EMS) Level 3 option installed.
A PDU/RPP distributes power through one or more circuit breaker
panels. Each panel consists of several circuit breakers. Each circuit
breaker monitors more than 30 parameters, such as voltage, current,
power, and alarms. The value of each parameter is stored in a
corresponding Modbus data register.
Because there are many panels in a PDU/RPP, it is necessary to identify
a specific breaker and specify the panel containing that breaker. It is
likely that Breaker #5 in Panel #1 has different data than Breaker #5 in
Panel #7.
The tables in this chapter list the names of the PDU/RPP parameters and
their corresponding Modbus registers for:
S PDU/RPP summary data
S Panel summary data
S Breaker data
The values of the parameters can be read over an Ethernet network by
using Modbus TCP/IP building monitoring programs or Modbus TCP/IP
analyzer programs.
NOTE Some Modbus programs provide an option for zero- or one-based addressing. Select
the option for zero-based addressing. The Modbus numbering scheme for the PDU/RPP starts
at 0, so physical coil number 1 corresponds to Modbus register number 0, coil number 2
corresponds to Modbus register number 1, and so on.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
49
MODBUS REGISTERS
Modbus Register Addressing
This section describes Modbus function codes, data formats, and data
addressing.
Modbus Function Codes
The PDU/RPP registers are read using Modbus Function Codes (FC). For
most PDU/RPP registers, FC 04 is used. The PDU/RPP supports the
following hex function codes:
Table 1. Function Codes
FC
Hex
Description
Use
01
0x01
Read Coil Status
Supported for compatibility purposes
02
0x02
Read Discrete Inputs
Single input data, such as alarms and
discrete contacts
03
0x03
Read Holding Registers
Supported for compatibility purposes
04
0x04
Read Input Registers
Analog data (most string and numeric
data types), such as voltage
05
0x05
Write Single Coil
For future use
06
0x06
Write Single Register
For future use
0F
0x0F
Write Multiple Coils
For future use
10
0x10
Write Multiple Registers
For future use
Data Formats
Modbus programs usually provide an option for viewing various data
types. Refer to your Modbus program documentation for detailed
information on viewing data options.
A register is 16 bits (two bytes). The PDU/RPP supports the following
data types:
S STRING – A string of ASCII characters (two per register). Consult the
Size parameter to find the string’s length for a given entry (it is a
multiple of two so that entries are register-aligned).
S FLOAT – A 32-bit IEEE754 floating point number. FLOATs are always
two registers.
S UINT – An unsigned integer. Consult the Size parameter to find the
integer’s size for a given entry (it is a multiple of two so that entries
are register-aligned).
50
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
S TIME – The Time type (ymdhms) consists of six bytes specifying the
year, month, day, hour, minutes, and seconds. The bytes are stored
in hexadecimal format. If your Modbus application displays the
individual bytes in a register, view the bytes using the decimal option.
Otherwise, the bytes are best viewed by displaying the two-byte
register in a binary format and translating each byte to decimal.
For example, if today is May 17, 2007 and the time is 10:45 and
20 seconds, viewing each hex byte in decimal would yield the
following data, which is viewable as the year (07), month (05),
day (17), hour (10), minutes (45), and seconds (20):
07
05
17
10
45
20
S BOOL – A binary (Boolean) value of 0 or 1. BOOL is usually assigned to
discrete input alarms.
Data Addressing
The register addresses and sizes listed in Table 3 through Table 9,
starting on page 54, specify an address for each entry. If a data type
spans multiple registers (such as a FLOAT), lower addressed registers
map to higher-order parts of the value. Within each register, data is in
most significant bit (MSB) first format.
NOTE A Modbus register contains two bytes. Therefore, the number of registers
containing the information can be obtained by dividing the bytes by two. For example, the
vendor name in Table 3 on page 54 can be obtained by reading 32 Modbus registers starting
at register 1001.
NOTE If a register is not supported in a particular device, an exception response is
returned.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
51
MODBUS REGISTERS
PDU/RPP Unit ID Numbers
Because the PDU/RPP consists of several panels of circuit breakers, set
the Unit ID in the Modbus program to specify a specific PDU/RPP, a
specific panel, or a specific breaker (see Table 2).
The PDU/RPP has a Unit ID of 0, 1, or 255. The same PDU/RPP
information can be obtained from any of these IDs. See “PDU/RPP
Registers and Alarms” on page 54 for more information.
The panel Unit IDs range from 2 to 17. These summary data panel
registers contain the total information for all the breakers in a specific
panel. For example, the registers show the sum total current for each
phase distributed by all the breakers. See “Panel Registers and Alarms”
on page 60 for more information.
The breaker Unit IDs range from 18 to 33. These registers provide
individual breaker data for the specified panel. See “Breaker Data and
Alarms” on page 64 for more information on identifying specific breaker
registers.
If there is an optional Environmental Monitoring Probe (EMP) installed,
use Unit ID 254 to obtain EMP data. See “Environmental Monitoring
Probe (FC 03 or 04)” on page 68 for more information.
Table 2. PDU/RPP Unit ID Numbers
Unit ID
52
Description
0
PDU/RPP Summary Data
1
PDU/RPP Summary Data
2
Panel #1 Summary Data
3
Panel #2 Summary Data
4
Panel #3 Summary Data
5
Panel #4 Summary Data
6
Panel #5 Summary Data
7
Panel #6 Summary Data
8
Panel #7 Summary Data
9
Panel #8 Summary Data
10
Panel #9 Summary Data
11
Panel #10 Summary Data
12
Panel #11 Summary Data
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 2. PDU/RPP Unit ID Numbers (continued)
Unit ID
Description
13
Panel #12 Summary Data
14
Panel #13 Summary Data
15
Panel #14 Summary Data
16
Panel #15 Summary Data
17
Panel #16 Summary Data
18
Panel #1 Breaker Data
19
Panel #2 Breaker Data
20
Panel #3 Breaker Data
21
Panel #4 Breaker Data
22
Panel #5 Breaker Data
23
Panel #6 Breaker Data
24
Panel #7 Breaker Data
25
Panel #8 Breaker Data
26
Panel #9 Breaker Data
27
Panel #10 Breaker Data
28
Panel #11 Breaker Data
29
Panel #12 Breaker Data
30
Panel #13 Breaker Data
31
Panel #14 Breaker Data
32
Panel #15 Breaker Data
33
Panel #16 Breaker Data
254
Environmental Monitoring Probe
255
PDU/RPP Summary Data
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
53
MODBUS REGISTERS
PDU/RPP Registers and Alarms
This section contains information for the PDU/RPP Registers (FC 04) and
PDU/RPP Alarms (FC 02).
PDU/RPP Registers (FC 04)
To read the vendor name in the PDU/RPP, set the Modbus program to
Unit ID 1 and register 1001:
IP: <IP address of PDU/RPP>
Unit ID: 1
Starting Register: 1001
Number of registers: 32
Function Code: 04
The PDU/RPP returns 32 registers containing up to 64 characters. There
are two ASCII characters per register, so the vendor name could be
displayed as POWERWARE.
Table 3. PDU/RPP Registers (FC 04)
Name
54
Register
Data Type
Bytes
Vendor Name
1001
STRING
64
Model Name
1033
STRING
64
Display Name
1065
STRING
64
Device Type
1097
UINT
4
Device ID
1099
UINT
4
Device Guid
1103
STRING
40
Serial Number
1123
STRING
64
Conn Style
1159
UINT
2
Device Comm Address
1160
STRING
64
Device Baud Rate
1192
UINT
4
Time Sync Period
1194
UINT
4
Data Update Period
1196
UINT
4
Device VAR Rating
1198
UINT
4
Device Volts In Rating
1204
UINT
4
Device Volts Out Rating
1206
UINT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 3. PDU/RPP Registers (FC 04) (continued)
Name
Register
Data Type
Bytes
Number of Phases
1208
UINT
2
Parallel System Flag
1209
UINT
2
Number of Controlled Banks
1210
UINT
2
Device Topology
1211
UINT
2
Asset ID
1324
STRING
128
Number of Panels
1453
UINT
2
Status
3000
UINT
2
Redundant State
3004
UINT
2
Horn Status
3005
UINT
2
Enter Admin State
3047
UINT
2
Enter Operating State
3048
UINT
2
Enter Readiness State
3049
UINT
2
Enter Alarm State
3050
UINT
2
Enter Standby State
3051
UINT
2
AC V in Phase AB
4028
FLOAT
4
AC V in Phase BC
4030
FLOAT
4
AC V in Phase CA
4032
FLOAT
4
AC V in Phase A
4040
FLOAT
4
AC V in Phase B
4042
FLOAT
4
AC V in Phase C
4044
FLOAT
4
AC V out Phase A
4046
FLOAT
4
AC V out Phase B
4048
FLOAT
4
AC V out Phase C
4050
FLOAT
4
AC V ratio A in
4154
FLOAT
4
AC V ratio B in
4156
FLOAT
4
AC V ratio C in
4158
FLOAT
4
AC V ratio A out
4160
FLOAT
4
AC V ratio B out
4162
FLOAT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
55
MODBUS REGISTERS
Table 3. PDU/RPP Registers (FC 04) (continued)
Name
56
Register
Data Type
Bytes
AC V ratio C out
4164
FLOAT
4
AC I Gnd
5008
FLOAT
4
AC I in A
5022
FLOAT
4
AC I in B
5024
FLOAT
4
AC I in C
5026
FLOAT
4
AC I out A
5028
FLOAT
4
AC I out B
5030
FLOAT
4
AC I out C
5032
FLOAT
4
AC I out N
5034
FLOAT
4
AC I out A Limit
5038
FLOAT
4
AC I out B Limit
5040
FLOAT
4
AC I out C Limit
5042
FLOAT
4
AC I ratio A in
5094
FLOAT
4
AC I ratio B in
5096
FLOAT
4
AC I ratio C in
5098
FLOAT
4
AC I ratio A out
5100
FLOAT
4
AC I ratio B out
5102
FLOAT
4
AC I ratio C out
5104
FLOAT
4
Watts in Total
6022
FLOAT
4
Watts out Total
6024
FLOAT
4
VA in Total
6086
FLOAT
4
VA out Total
6088
FLOAT
4
PF Disp out
6202
FLOAT
4
PF Disp in
6204
FLOAT
4
Output kW Hours
7002
FLOAT
4
I A in THD
8008
FLOAT
4
I B in THD
8010
FLOAT
4
I C in THD
8012
FLOAT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 3. PDU/RPP Registers (FC 04) (continued)
Name
Register
Data Type
Bytes
I A out THD
8014
FLOAT
4
I B out THD
8016
FLOAT
4
I C out THD
8018
FLOAT
4
VA in THD
8042
FLOAT
4
VB in THD
8044
FLOAT
4
VC in THD
8046
FLOAT
4
VA in THD
8048
FLOAT
4
VB in THD
8050
FLOAT
4
VC in THD
8052
FLOAT
4
CFph A out
8312
FLOAT
4
CFph B out
8314
FLOAT
4
CFph C out
8316
FLOAT
4
Output Frequency
11002
FLOAT
4
Input Frequency
11004
FLOAT
4
Current Time
12203
TIME
6
PDU/RPP Alarms (FC 02)
The PDU/RPP monitors the condition of several parameters and can
activate an alarm status if a parameter is out of range. For example, if
the input frequency is too high or too low, the PDU/RPP can set the
Input Frequency Fault Alarm.
To read the Input Frequency Fault Alarm, set the Modbus program to
Unit ID 1 and coil address 1008:
IP: <IP address of PDU>
Unit ID: 1
Starting Register: 1008
Number of Registers: 1
Function Code: 02
The PDU/RPP returns a single register that is a BOOL value (0 or 1),
indicating if the alarm is active or not active.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
57
MODBUS REGISTERS
Table 4. PDU/RPP Alarms (FC 02)
Name
58
Register
Data Type
AC Input Over Volts
1006
BOOL
AC Input Under Volts
1007
BOOL
Input Frequency Fault
1008
BOOL
AC Output Over Volts
1009
BOOL
AC Output Under Volts
1010
BOOL
AC Output Frequency Fault
1011
BOOL
Remote EPO
1012
BOOL
Building Alarm 4
1016
BOOL
Building Alarm 3
1017
BOOL
Building Alarm 2
1018
BOOL
Building Alarm 1
1019
BOOL
Output Overload
1025
BOOL
System Bus Overload
1050
BOOL
NV Memory Failure
1053
BOOL
Internal Comm Failure
1062
BOOL
Input Phase Rotation
1089
BOOL
Emergency Shutdown
1093
BOOL
Overload A
1139
BOOL
Overload B
1140
BOOL
Overload C
1141
BOOL
Overload High Phase A
1142
BOOL
Overload High Phase B
1143
BOOL
Overload High Phase C
1144
BOOL
Overload Extreme Phase A
1145
BOOL
Overload Extreme Phase B
1146
BOOL
Overload Extreme Phase C
1147
BOOL
Xformer Over Temperature
1164
BOOL
Check Modem
1174
BOOL
Configuration Error
1182
BOOL
System Notice Active
1185
BOOL
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 4. PDU/RPP Alarms (FC 02) (continued)
Name
Register
Data Type
System Alarm Active
1186
BOOL
Inverter Rotation
1192
BOOL
Invalid Board ID
1195
BOOL
Output Watts Overload
1197
BOOL
Xformer Over Temp Warning
1210
BOOL
Input THD High A
1212
BOOL
Input THD High B
1213
BOOL
Input THD High C
1214
BOOL
Output THD High A
1215
BOOL
Output THD High B
1216
BOOL
Output THD High C
1217
BOOL
Neutral Overload Warning
1218
BOOL
Neutral Overload
1219
BOOL
Ground Current Warning
1220
BOOL
Ground Current Overload
1221
BOOL
V Input THD Warning A
1222
BOOL
V Input THD Warning B
1223
BOOL
V Input THD Warning C
1224
BOOL
I Input THD Warning A
1225
BOOL
I Input THD Warning B
1226
BOOL
I Input THD Warning C
1227
BOOL
V Output THD Warning A
1228
BOOL
V Output THD Warning B
1229
BOOL
V Output THD Warning C
1230
BOOL
I Output THD Warning A
1231
BOOL
I Output THD Warning B
1232
BOOL
I Output THD Warning C
1233
BOOL
Panel Phase A Loss
1235
BOOL
Panel Phase B Loss
1236
BOOL
Panel Phase C Loss
1237
BOOL
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
59
MODBUS REGISTERS
Table 4. PDU/RPP Alarms (FC 02) (continued)
Name
Register
Data Type
Branch Breaker Overload Warning
1249
BOOL
Branch Breaker Overload
1250
BOOL
Branch Breaker Disconnected
1252
BOOL
Main Breaker Overload Warning
1253
BOOL
Main Breaker Overload
1254
BOOL
Primary Breaker Open
1256
BOOL
Primary Breaker Tripped
1257
BOOL
Secondary Breaker Open
1258
BOOL
Secondary Breaker Tripped
1259
BOOL
Input Phase Rotation
1477
BOOL
Panel Registers and Alarms
This section contains information for the Panel Summary Registers
(FC 04) and the Panel Alarms (FC 01 or 02).
Panel Summary Registers (FC 04)
NOTE The panel can be wired for either a wye (phase to neutral) or a delta
(phase-to-phase) configuration. The registers contain only the data supported by the wired
configuration. For example, if the panel is wired in a wye configuration, the voltages AN, BN,
and CN are available, but the voltages AB, BC, and CA are not available (an exception code is
returned). Refer to the actual panel for the wiring configuration.
Table 5 shows the registers that contain summary data for the panel.
The registers contain the total information for all the breakers in the
panel.
60
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
For example, the AC Voltage between Phase A and Neutral is available
in register 4010. To read the AC Voltage in Phase A at Panel #1, set the
Modbus program to Unit ID 2 and register 4010:
IP: <IP address of PDU/RPP>
Unit ID: 2
Starting Register: 4010
Number of Registers: 2
Function Code: 04
To read the AC Voltage in Phase A at Panel #4, set the Modbus program
to Unit ID 5 and register 4010:
IP: <IP address of PDU/RPP>
Unit ID: 5
Starting Register: 4010
Number of Registers: 2
Function Code: 04
Table 5. Panel Summary Registers (FC 04)
Name
Register
Data Type
Bytes
Display Template
1000
UINT
2
Vendor Name
1001
STRING
64
Model Name
1033
STRING
64
Display Name
1065
STRING
64
Serial Number
1123
STRING
64
Device Volts Rating
1202
UINT
4
Number of Phases
1208
UINT
2
Asset ID
1324
STRING
128
Breaker Rating
1453
UINT
2
Breaker Warning
1456
UINT
2
Breaker Overload
1457
UINT
2
Neutral Current Alarm
1459
UINT
2
Enter Admin State
3047
UINT
2
Enter Operating State
3048
UINT
2
Enter Readiness State
3049
UINT
2
Enter Alarm State
3050
UINT
2
Enter Standby State
3051
UINT
2
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
61
MODBUS REGISTERS
Table 5. Panel Summary Registers (FC 04) (continued)
Name
62
Register
Data Type
Bytes
AC V AN
4010
FLOAT
4
AC V BN
4012
FLOAT
4
AC V CN
4014
FLOAT
4
AC V MAX AN
4296
FLOAT
4
AC V MAX BN
4298
FLOAT
4
AC V MAX CN
4300
FLOAT
4
AC I in A
5002
FLOAT
4
AC I in B
5004
FLOAT
4
AC I in C
5006
FLOAT
4
AC I in N
5010
FLOAT
4
AC I MAX A
5164
FLOAT
4
AC I MAX B
5166
FLOAT
4
AC I MAX C
5168
FLOAT
4
AC I MAX N
5170
FLOAT
4
Percent Full Load Current A
5185
FLOAT
4
Percent Full Load Current B
5186
FLOAT
4
Percent Full Load Current C
5188
FLOAT
4
Watts Total
6006
FLOAT
4
Watts Total MAX
6014
FLOAT
4
VA Total
6070
FLOAT
4
VA Total MAX
6078
FLOAT
4
PF Disp Total
6219
FLOAT
4
PF Disp Sys MIN
6268
FLOAT
4
PF Disp Sys MAX
6288
FLOAT
4
Watts Total MIN
6356
FLOAT
4
VA MIN
6364
FLOAT
4
kW Hour
7618
FLOAT
4
Monthly kW Hour
7620
FLOAT
4
Yearly kW Hour
7622
FLOAT
4
Frequency
11000
FLOAT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 5. Panel Summary Registers (FC 04) (continued)
Name
Register
Data Type
Bytes
MIN Frequency
11022
FLOAT
4
MAX Frequency
11027
FLOAT
4
Panel Alarms (FC 01 or 02)
Table 6 lists the panel alarms. They are not registers, but are discrete
inputs and are read using FC 01 or FC 02.
To read the Main Breaker Overload alarm at Panel #4, set the Modbus
program to Unit ID 5 and coil address 1254:
IP: <IP address of PDU/RPP>
Unit ID: 5
Starting Register: 1254
Number of Registers: 1
Function Code: 02
Table 6. Panel Alarms (FC 01 or 02)
Name
Coil/Status Address
Data Type
Neutral Overload
1219
BOOL
Panel Under Voltage
1238
BOOL
Panel Over Voltage
1242
BOOL
Panel Under Over Frequency
1248
BOOL
Branch Breaker Overload Warning
1249
BOOL
Branch Breaker Overload
1250
BOOL
Main Breaker Overload Warning
1253
BOOL
Main Breaker Overload
1254
BOOL
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
63
MODBUS REGISTERS
Breaker Data and Alarms
This section contains:
S Names of breaker parameters along with the register numbers for
Breaker #1
S Instructions for calculating the register numbers for other breakers
S Breaker alarms
Breaker #1 Data Registers (FC 04)
To specify a specific breaker, use a Unit ID for breaker data along with
the register number for the specific breaker.
For example, “Watts in Phase A” is register 1055 for Breaker #1. This
statement is true for any panel. To specify a specific panel for breaker
data, use the panel’s Unit ID in the Modbus program. For Panel #6
(Unit ID 23), the Modbus program would be set as follows:
IP: <IP address of PDU/RPP>
Unit ID: 23
Starting Register: 1055
Number of registers: 2
Function code: 04
The Modbus program would return a value of the watts in Phase A for
Breaker #1 in Panel #6 of the PDU/RPP at the specified IP address.
Table 7. Breaker #1 Data Registers (FC 04)
Name
64
Register
Data Type
Bytes
Display Name
1000
STRING
64
Number of Phases
1032
UINT
2
Breaker Rating
1033
UINT
4
Breaker Warning
1035
UINT
2
Breaker Overload
1036
UINT
2
AC Current Phase A
1037
FLOAT
4
AC Current Phase B
1039
FLOAT
4
AC Current Phase C
1041
FLOAT
4
AC MAX Current Phase A
1043
FLOAT
4
AC MAX Current Phase B
1045
FLOAT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Table 7. Breaker #1 Data Registers (FC 04) (continued)
Name
Register
Data Type
Bytes
AC MAX Current Phase C
1047
FLOAT
4
Percent FL Current A
1049
FLOAT
4
Percent FL Current B
1051
FLOAT
4
Percent FL Current C
1053
FLOAT
4
Watts Phase A
1055
FLOAT
4
Watts Phase B
1057
FLOAT
4
Watts Phase C
1059
FLOAT
4
Watts Phase A MAX
1061
FLOAT
4
Watts Phase B MAX
1063
FLOAT
4
Watts Phase C MAX
1065
FLOAT
4
VA Phase A
1067
FLOAT
4
VA Phase B
1069
FLOAT
4
VA Phase C
1071
FLOAT
4
VA Phase A MAX
1073
FLOAT
4
VA Phase B MAX
1075
FLOAT
4
VA Phase C MAX
1077
FLOAT
4
PF Displacement Phase A
1079
FLOAT
4
PF Displacement Phase B
1081
FLOAT
4
PF Displacement Phase C
1083
FLOAT
4
PF Displacement A Minimum
1085
FLOAT
4
PF Displacement B Minimum
1087
FLOAT
4
PF Displacement C Minimum
1089
FLOAT
4
PF Displacement A Maximum
1091
FLOAT
4
PF Displacement A Maximum
1093
FLOAT
4
PF Displacement A Maximum
1095
FLOAT
4
kW Hours
1097
FLOAT
4
kW Hours Monthly
1099
FLOAT
4
kW Hours Yearly
1101
FLOAT
4
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
65
MODBUS REGISTERS
Calculating Breaker Register Numbers
Table 7 shows the register numbers for Breaker #1. There can be many
breakers in a panel. Determine the corresponding register numbers for
other breakers in the panel by using the following formula:
Breaker register # = Breaker #1 register + ((Breaker # – 1) x 200))
For example:
Breaker #2 starts at 1200:
1000 + ((2 – 1) x 200)
1000 + (1 x 200)
1000 + 200
1200
Breaker #3 starts at 1400:
1000 + ((3 – 1) x 200)
1000 + (2 x 200)
1000 + 400
1400
Breaker #14 starts at 3600:
1000 + ((14 – 1) x 200)
1000 + (13 x 200)
1000 + 2600
3600
This formula works for any register. For example, for Breaker #1, the
register number of “Watts Phase A” is 1055. The corresponding
address for Breaker #18 is:
1055 + ((18 – 1) x 200)
1055 + (17 x 200)
1055 + 3400
4455
66
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
MODBUS REGISTERS
Breaker Alarms (FC 01 or 02)
There are two alarms for each circuit breaker: Overload Warning and
Overload. Each alarm has a unique address similar to the data registers,
but these alarms are not data registers. The alarms are discrete inputs
and are read using FC 01 or FC 02 in the Modbus program.
Table 8. Breaker Alarms (FC 01 or 02)
Name
Coil/Status Address
Data Type
Branch Breaker 1 Overload Warning
1000
BOOL
Branch Breaker 1 Overload
1001
BOOL
Table 8 shows the alarms for Breaker #1. Determine the corresponding
alarms for other breakers by using the following formula:
Breaker #5 address = ((Breaker number – 1) x 2) + Breaker #1 address
For example, to find the Overload Warning alarm address for Breaker #5:
Breaker #5 Overload Warning
= ((5 – 1) x 2) + 1000
= ((4) x 2) + 1000
= (8) + 1000
= 1008
To find the Overload alarm address for Breaker #20:
Breaker #20 Overload
= ((20 – 1) x 2) + 1001
= ((19) x 2) + 1001
= (38) + 1001
= 1039
To read the Overload Warning alarm for Breaker #5 in Panel #8, the
Modbus program would be set as follows:
IP: <IP address of PDU/RPP>
Unit ID: 25
Starting Register: 1008
Number of registers: 1
Function code: 02
The Modbus program would return a true/false value of the Overload
Warning alarm for Breaker #5 in Panel #8 of the PDU/RPP at the
specified IP address.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
67
MODBUS REGISTERS
Environmental Monitoring Probe (FC 03 or 04)
The optional Environmental Monitoring Probe for the PDU/RPP can
measure temperature and humidity. Because the device can be located
outside the PDU/RPP, the reference is to “auxiliary” data. In addition, it
contains two connections for monitoring the condition of auxiliary input
contacts, such as a door switch. See Table 9 for a list of EMP registers.
An exception code is returned if the EMP is not installed.
To read the temperature at the PDU/RPP, set the Modbus program to
Unit ID 254 and coil address 12028:
IP: <IP address of PDU/RPP>
Unit ID: 254
Starting Register: 12028
Number of registers: 2
Function Code: 04
Table 9. Environmental Monitor (FC 03 or 04)
Name
Register
Data Type
Bytes
Vendor Name
1001
STRING
64
Model Name
1033
STRING
64
Display Name
1065
STRING
64
Serial Number
1123
STRING
64
Device ID
1099
UINT
4
Auxiliary Input 1
10275
UINT
2
Auxiliary Input 2
10276
UINT
2
Auxiliary Temperature
12028
FLOAT
4
Auxiliary Humidity
12030
FLOAT
4
68
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 6
Specifications
Table 10. Technical Specifications
CPU
Atmel AT91RM9200 ARM-9
Memory
32 MB Static DRAM
32 MB Flash ROM
LAN Controller
AT91RM9200 Integrated – Port 1
SMSC LAN91C113I – Port 2
Network Connection
(2) 10/100BaseT RJ-45 network connectors
PDU Protocol
Powerware Power Distribution Unit (PDU) communication protocol
Network Protocols
(not limited to)
SNMP v1 over UDP/IP
Modbus TCP/IP
HTTP/HTTPS
BACnet/WS
BOOTP, DHCP
TCP/IP
Supported SNMP MIBs
Eaton PDU MIB
Eaton EMP MIB
Eaton Alarms+Traps MIB
Eaton OID assignments
RFC 1213 (MIB-II)
RFC 4133 (Entity MIB)
RFC 4268 (Entity State MIB)
Operating Temperature
0–40°C (32–104°F)
Operating Humidity
10–80%, noncondensing
Power Input
8–25 Vdc unregulated (12 Vdc nominal)
Power Consumption
2.0 watts maximum
Size (L x W x H)
12 cm x 11.4 cm x 3.9 cm (4.7” x 4.5” x 1.5”)
Weight
200 gm (7 oz)
EMC Statements
Class A: FCC Part 15
EU Standard: EN 55022:1988+A1:2000+A2:2003,
Class A/EN55022:1988+A1:2000+A2:2003
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
69
SPECIFICATIONS
70
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 7
Operation and Maintenance
This section explains:
S Indicator descriptions
S DIP switch settings
S Generating log files
S Firmware upgrade instructions
Front-Panel Indicator Descriptions
The Ethernet port indicator descriptions for the PXGX Series 1000 Card
are listed in Table 11; the stacked indicator descriptions are listed in
Table 12.
Table 11. Ethernet Port Indicators
Ethernet Port 1
Ethernet Port 2
Indicator Label
Illuminated
Not Illuminated
100
Indicates a valid 100 Mb Connection
(Link).
Indicates a valid 10 Mb Connection (Link)
as long as the corresponding ACT
indicator is illuminated.
ACT
Indicates network activity when the
indicator is on or blinking.
Indicates network activity when the
indicator is on or blinking.
100
Indicates a valid 100 Mb Connection
(Link).
Indicates a valid 10 Mb Connection (Link)
as long as the corresponding ACT
indicator is illuminated.
ACT
Indicates network activity when the
indicator is on or blinking.
Indicates network activity when the
indicator is on or blinking.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
71
OPERATION AND MAINTENANCE
Table 12. Stacked Indicator Descriptions
Label
Color
Illuminated
Not Illuminated
STATUS
Green
Communication with the PDU has been
established.
Communication with the PDU has not
been established. As the card boots, the
indicator remains off. However, if it
remains off after one minute, there is a
communication problem between the
card and the PDU.
DHCP
Amber
At least one port is configured for DHCP
and has obtained IP address information.
The use of DHCP/BOOTP has been
disabled by the user, or all ports
configured for DHCP have failed to obtain
IP address information.
IDENT
Red
A firmware update is in progress. Do not
remove the card from the PDU.
A firmware update is not in progress.
POWER
Green
DC power is available to the card from
the PDU.
If all indicators are not illuminated, DC
power is not available from the PDU. This
may indicate that the PDU is off and
unplugged.
NOTE During the power-on sequence, all four indicators are illuminated for approximately 20 seconds. Wait at least
one minute for the card’s boot process to complete before comparing the indicators to the table above because
indicators may turn on and off at different times in the boot process.
72
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
OPERATION AND MAINTENANCE
DIP Switch Description
DIP switch definitions for the PXGX Series 1000 Card are listed in
Table 13.
Table 13. DIP Switch Definitions
S1 Position
Number
OFF Position (Default)
ON Position
1
Enable previously stored network
configuration settings (Normal
mode)
Override network settings to
assign private IP addresses
(Configuration mode); Port 1 is set
to 192.168.1.1 and Port 2 is set to
192.168.1.2
2
Enable the front panel RJ-45 for
serial communication
Enable the front panel RJ-45 port
for communication with an
Environmental Monitoring Probe
(EMP) device for immediate or
future use
3
Normal behavior
Reset the HTTP passwords to the
defaults on boot (user and
admin). After a successful boot,
the switch should be turned back
off before rebooting the card.
4
Reserved
Reserved
5
Reserved
Reserved
6
Normal behavior
Reset the card to factory defaults
on boot (after a successful boot,
the switch should be turned back
off before rebooting the card)
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
73
OPERATION AND MAINTENANCE
Generating Log Files
NOTE The data log and event log files are comma-separated values (*.csv) files that can
be opened in Microsoft Excel software. Some computer configurations will automatically
open the files in the Microsoft Excel software instead of prompting you to save.
To generate a data log:
1.
From the card’s Web page, click the Data Log link from the menu
bar.
2.
Click the Click to generate button.
3.
Select a name and location for the file (if prompted to save).
To generate an event log:
1.
From the card’s Web page, click the Event Log link from the menu
bar.
2.
Click the Click to generate button.
3.
Select a name and location for the file (if prompted to save).
Upgrading the Card’s Firmware
The card’s firmware may be updated by downloading the appropriate file
from www.eaton.com/powerxpert. During the upgrade process, the
PXGX Series 1000 Card does not monitor the PDU status.
To upgrade the firmware:
74
1.
From the card’s Web page, click the Firmware link from the menu
bar.
2.
Click the Browse button.
3.
Download the pxgx_pdu_xxx.rom firmware file, available on the
Web at www.eaton.com/powerxpert.
4.
After updating the firmware, the card prompts you to reboot. Click
OK to reboot the card. An audible alarm sounds as the card reboots,
and the Web page shows the “Gateway rebooting, please wait...”
message. The Web page refreshes after approximately 75 seconds.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
Chapter 8
Service and Support
If you have any questions or problems with the PXGX Series 1000 Card,
call your Local Distributor or the Help Desk at one of the following
telephone numbers and ask for a PXGX Series 1000 Card technical
representative.
United States:
Canada:
All other countries:
1-800-843-9433 or 1-919-870-3028
1-800-461-9166 ext 260
Call your local service representative
Please have the following information ready when you call the Help
Desk:
S Model number
S Serial number
S Version number (if available)
S Date of failure or problem
S Symptoms of failure or problem
S Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the package
and on the Bill Of Lading (if applicable). Use the original packaging or
request packaging from the Help Desk or distributor. Units damaged in
shipment as a result of improper packaging are not covered under
warranty. A replacement or repair unit will be shipped, freight prepaid for
all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the Help
Desk for the dealer or distributor nearest you.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
75
SERVICE AND SUPPORT
Two-Year Limited Warranty (US and Canada)
Power Xpert Gateway (PXGX) Series 1000 and Series 2000 Cards
WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Electrical Inc., a Delaware
Corporation company (“Company”).
LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original End-User (the “End-User”)
of the Power Xpert Gateway (PXGX) Series 1000 or Series 2000 Card (the “Product”) purchased on or after June 1,
2004 and cannot be transferred. This Warranty applies even in the event that the Product is initially sold by
Company for resale to an End-User.
LIMITED WARRANTY PERIOD: The period covered by this Warranty for the Product installed [and currently located]
in the fifty (50) United States, the District of Columbia, and Canada is twenty-four (24) months from the date of
purchase.
WHAT THIS LIMITED WARRANTY COVERS: The warrantor warrants that the Product (the “Warranted Item”) is free
from defects in material and workmanship. If, in the opinion of Company, a Warranted Item is defective and the
defect is within the terms of this Warranty, Company’s sole obligation will be to repair or replace such defective
Warranted Item (including by providing service, parts and labor, as applicable), at the option of Company.
PROCEDURES FOR REPAIR OR REPLACEMENT OF WARRANTED ITEMS: The Warranted Item will be repaired or
replaced at a Company site or such other location as determined by Company.
If the Warranted Item is to be replaced by Company, and the End-User supplies a credit card number or purchase
order for the value of the replacement Product, Company will use commercially reasonable business efforts to ship
(via standard ground shipment and at no cost to the End-User) the replacement Warranted Item to the End-User
within one (1) business day after Company receives notice of the warranty claim. In such case, the End-User must
return (at Company’s expense) the defective Warranted Item to Company in the same packaging as the
replacement Warranted Item received by the End-User or as otherwise instructed by Company. If Company does
not receive the defective Warranted Item, Company will either charge the End-User’s credit card, or send the
End-User an invoice (which the End-User agrees to pay), for the value of the replacement Product.
If the Warranted Item is to be replaced by Company, but the End-User is unwilling or unable to supply a credit card
number or purchase order for the value of the replacement Product, Company will use commercially reasonable
business efforts to ship (via standard ground shipment and at no cost to the End-User) the replacement Warranted
Item to the End-User within one (1) business day after Company receives the defective Product from the End-User.
In any case, Company will provide shipping instructions and will pay its designated carrier for all shipping charges for
return of defective equipment and replacement of Warranted Items. Any returned Warranted Item or parts that are
replaced may be new or reconditioned. All Warranted Items returned to Company and all parts replaced by
Company shall become the property of Company.
WHAT THIS LIMITED WARRANTY DOES NOT COVER: This Warranty does not cover any defects or damages
caused by: (a) failure to properly store the Product before installation; (b) shipping and delivery of the Product if
shipping is FOB Factory; (c) neglect, accident, abuse, misuse, misapplication, or incorrect installation; (d) repair or
alteration not authorized in writing by Company personnel or performed by an authorized Company Customer
Service Engineer or Agent; (e) improper testing, operation, maintenance, adjustment, or modification of any kind not
authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or
Agent; or (f) use of the Product under other than normal operating conditions or in a manner inconsistent with the
Product’s labels or instructions.
This Warranty is not valid if the Product’s serial numbers have been removed or are illegible. Any Warranted Items
repaired or replaced pursuant to this Warranty will be warranted for the remaining portion of the original Warranty
subject to all the terms thereof.
76
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
SERVICE AND SUPPORT
Company shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items.
COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY. IF PERMITTED BY THE
APPLICABLE MANUFACTURER, COMPANY SHALL PASS THROUGH SUCH MANUFACTURER’S WARRANTIES TO
END-USER.
COMPANY DOES NOT WARRANT SOFTWARE (IF APPLICABLE TO THE PRODUCT), INCLUDING SOFTWARE
EMBEDDED IN PRODUCTS, THAT IS NOT CREATED BY COMPANY. WITHOUT LIMITING THE FOREGOING,
COMPANY SPECIFICALLY DOES NOT WARRANT SOFTWARE (SUCH AS LINUX®) THAT WAS CREATED USING AN
“OPEN SOURCE” MODEL OR IS DISTRIBUTED PURSUANT TO AN OPEN SOURCE LICENSE.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OFFERED BY COMPANY WITH RESPECT TO THE
PRODUCTS AND SERVICES AND, EXCEPT FOR SUCH FOREGOING WARRANTY COMPANY DISCLAIMS ALL OTHER
WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, TITLE,
NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE. CORRECTION OF NON-CONFORMITIES IN
THE MANNER AND FOR THE PERIOD OF TIME PROVIDED ABOVE SHALL CONSTITUTE COMPANY’S SOLE
LIABILITY AND END-USER’S EXCLUSIVE REMEDY FOR FAILURE OF COMPANY TO MEET ITS WARRANTY
OBLIGATIONS, WHETHER CLAIMS OF THE END-USER ARE BASED IN CONTRACT, IN TORT (INCLUDING
NEGLIGENCE OR STRICT LIABILITY), OR OTHERWISE.
LIMITATION OF LIABILITY: The remedies of the End-User set forth herein are exclusive and are the sole remedies
for any failure of Company to comply with its obligations hereunder. In no event shall Company be liable in contract,
in tort (including negligence or strict liability) or otherwise for damage to property or equipment other than the
Products, including loss of profits or revenue, loss of use of Products, loss of data, cost of capital, claims of
customers of the End-User or any special, indirect, incidental or consequential damages whatsoever. The total
cumulative liability of Company hereunder whether the claims are based in contract (including indemnity), in tort
(including negligence or strict liability) or otherwise, shall not exceed the price of the Product on which such liability
is based.
Company shall not be responsible for failure to provide service or parts due to causes beyond Company’s
reasonable control.
END-USER’S OBLIGATIONS: In order to receive the benefits of this Warranty, the End-User must use the Product
in a normal way; follow the Product’s user’s guide; and protect against further damage to the Product if there is a
covered defect.
OTHER LIMITATIONS: Company’s obligations under this Warranty are expressly conditioned upon receipt by
Company of all payments due to it (including interest charges, if any). During such time as Company has not
received payment of any amount due to it for the Product, in accordance with the contract terms under which the
Product is sold, Company shall have no obligation under this Warranty. Also during such time, the period of this
Warranty shall continue to run and the expiration of this Warranty shall not be extended upon payment of any
overdue or unpaid amounts.
COSTS NOT RELATED TO WARRANTY: The End-User shall be invoiced for, and shall pay for, all services not
expressly provided for by the terms of this Warranty, including without limitation, site calls involving an inspection
that determines no corrective maintenance is required. Any costs for replacement equipment, installation, materials,
freight charges, travel expenses or labor of Company representatives outside the terms of this Warranty will be
borne by the End-User.
OBTAINING WARRANTY SERVICE: In the USA, call the Customer Reliability Center 7x24 at 800-356-5737. Outside
of the USA, contact your local Eaton product sales or service representative, or call the Customer Reliability Center
in the USA at 919-870-3149. For comments or questions about this Warranty, write to the Customer Quality
Representative, 3301 Spring Forest Road, Raleigh, North Carolina 27616 USA.
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
77
SERVICE AND SUPPORT
78
EATON Power Xpert® Gateway Series 1000 Card User’s Guide S 164201670 Rev 1
*1642016701*
164201670 1
Download PDF

advertising