Operator`s manual | Echo 400 LH Trimmer User Manual

PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
PAS Articulating Hedge Clipper Attachment
Operator's Manual
MODEL
FOR MODELS:
99944200595
SRM-2100SB/2400SB
SRM-210SB/211SB
SRM-225SB
SRM-260SB/261SB
PAS-2100/2400
PAS-210/211
PAS-230/231
PAS-260/261
PAS-2601
PAS-265
WARNING
Read rules for safe operation and instructions carefully. ECHO provides an
Operator's Manual and a Safety Manual for Pro Attachment Series power source or
Split Boom Trimmer. Those manuals and this manual must be read and understood
for proper and safe operation, otherwise serious personal injury may result.
X7532095603
X753001923
01/09
1
2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life
and on-the-job-dependability. Read and understand this manual included with your attachment. You will
find this manual easy to use and full of helpful operations tips and SAFETY messages.
THE OPERATOR'S MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It contains specifications and information for
operation and maintenance specific to the attachment.
THE SAFETY MANUAL
Explains possible hazards and what measures you should take to insure
safe operation.
TABLE OF CONTENTS
Introduction ...................................................................... 2
- The Operator's Manual .............................................. 2
- The Safety Manual .................................................... 2
Safety ................................................................................ 3
- Manual Safety Symbols and Important Information .. 3
- International Symbols ................................................ 3
- Personal Condition and Safety Equipment ................ 4
- Equipment .................................................................. 6
Description ....................................................................... 6
Contents ........................................................................... 7
Assembly .......................................................................... 8
- Power Head Shaft/Lower Shaft Assembly ................. 8
Operation .......................................................................... 9
- Adjusting Cutting Angle ........................................... 9
- Rotate Cutter Assembly .......................................... 10
- Hdege Trimming ...................................................... 10
Copyright© 2009 By Echo, Incorporated
All Rights Reserved.
Maintenance ............................................................ 11
- Skill Levels ........................................................ 11
- Maintenance Intervals ...................................... 11
- Lubrication ........................................................ 11
- Sharpening Blades ........................................... 13
- Blade Adjustment ............................................. 14
Storage ..................................................................... 15
Specifications ........................................................... 15
Servicing Information ............................................... 16
- Parts/Serial Number .......................................... 16
- Service .............................................................. 16
- ECHO Consumer Product Support .................... 16
- Warranty Card .................................................. 16
- Additional or Replacement Manuals ................ 16
Specifications, descriptions and illustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard
equipment.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages
preceded by symbols or key words. The following is an explanation of those symbols and key words and what they
mean to you.
DANGER
CIRCLE AND SLASH SYMBOL
The safety alert symbol accompanied by the
word “DANGER” calls attention to an act or
condition which WILL lead to serious personal
injury or death if not avoided.
WARNING
The safety alert symbol accompanied by the
word “WARNING” calls attention to an act or
condition which CAN lead to serious personal
injury or death if not avoided.
CAUTION
The safety alert symbol accompanied by the
word “CAUTION” calls attention to an act or
condition which may lead to minor or moderate
personal injury if not avoided.
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or fatal
injury.
NOTE
This enclosed message provides tips for use, care
and maintenance of the unit.
IMPORTANT
The enclosed message provides information necessary for the protection of the unit.
INTERNATIONAL SYMBOLS
Symbol form/shape
Symbol
description/application
Symbol form/shape
Symbol
description/application
Symbol form/shape
Symbol
description/application
Read and
understand
Operator's Manual.
Fuel and oil
mixture
Wear eyes, ears
and head
protection
Finger Severing
Choke Control
"Cold Start"
Position
(Choke Closed)
Hot
Surface
Wear hand
protection. Use
two handed.
Choke Control
"Run"
Position
(Choke Open)
Safety/Alert
DO NOT smoke
near fuel.
Avoid all power
lines. This unit is
not insulated
against electrical
current.
DO NOT allow
flames or sparks
near fuel.
Do not operate
closer than 15 M
(50 ft.) from
electrical
hazards.
Keep bystanders
at least 15 meters
(50 feet) away.
Emergency stop
Primer bulb
Carburetor
adjustment
- Low speed
mixture
Symbol form/shape
Symbol
description/application
Plan retreat path
from falling
objects.
Wear slip
resistant foot
wear.
Ignition
ON/OFF
Carburetor
adjustment
- High speed
mixture
Carburetor
adjustment
- Idle speed
3
4
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions
are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.
Hand Protection
Wear no-slip, heavy-duty work gloves to improve your grip on the handle. Gloves also reduce the transmission of
machine vibration to your hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARFS, JEWELRY.
Wear protective hair covering to contain long hair.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early
morning or late afternoon hours when temperatures are cooler.
Extended Operation/Extreme Conditions
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning
sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended, because the minimum exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can
cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
fingers encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
Cutting Angle Adjustments
• Only adjust cutting blade angle with unit flat on the ground, with the
engine stop switch in the “STOP” position. Never adjust cutting
angle with unit standing upright.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
5
6
EQUIPMENT
WARNING
Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment
combination. Read and comply with all safety instructions listed in this manual and safety manual. ECHO, INC. will
not be responsible for the failure of cutting devices or accessories which have not been tested and approved by
ECHO for use with this unit.
•
•
•
•
Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
Never adjust blades when the engine is operating.
Inspect hand guard for damage. Replace if damaged or missing.
Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades
should not be used.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
DESCRIPTION
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDER3
ING instructions for specific information.
8
Shaft Decal
P/N X505000531
4
5
2
P/N 89016012360
1
6
7
P/N 89017854331
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
1.
CUTTING BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable
of cutting on either side of the blade.
2.
LOWER DRIVE SHAFT ASSEMBLY - Includes the Gear Housing assembly, Flexible Drive Cable, Blade and Safety
Decals.
3.
FLEXIBLE DRIVE CABLE - Cable end fits into upper drive shaft coupler. Lubricate drive cable every 25 hours with
ECHO® LUBETM grease.
4.
FRONT DRIVE SHAFT GRIP - Cushioned hand grip for gripping drive shaft assembly.
5.
HAND GUARD / BLADE LOCK - Locks blade in place for travel / storage. Always assure blade cover is installed
when locking blade.
6.
BLADE ADJUSTMENT HANDLE - Provides secure hand grip for adjusting cutting blade angle.
7.
BLADE INDEXING RING- Pull ring out and turn 1/4 turn to lockout position when adjusting blade angle.
8.
BLADE COVER - Used to cover blades during transport and storage. Remove blade cover before operating unit.
CONTENTS
The ECHO product you have purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
Use the contents list to check for missing parts.
_____
_____
_____
_____
_____
_____
1 - Articulating Hedge Clipper Attachment
1 - Operator's Manual
1 - Hedge Clipper Safety Manual
1 - Warranty Registration Card
1 - Blade Cover
1 - Storage Hook Assembly
7
8
ASSEMBLY
POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY
Tools Required: None
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
1.
Set Power Head/Shaft Assembly on a level surface.
2.
Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lockout position.
3.
Remove vinyl cap from attachment drive shaft.
4.
Carefully fit attachment drive shaft assembly into coupler (B) to
decal assembly line (C), making sure that the inner lower drive shaft
engages into the square upper drive shaft socket.
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings fit flush to decal point (E). New couplings are 4-3/4 in.
long, and fit flush to line (C).
5.
Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap flush in coupler. Full engagement
will prevent further shaft rotation.
6.
Secure lower shaft assembly to coupler by tightening clamping
knob (D).
B
D
E
C
A
D
C
A
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
9
OPERATION
WARNING
All over head electrical conductors and communications wires can have electricity flow with high voltages. Never
touch wires directly or indirectly when pruning, otherwise serious injury or death may result.
ADJUSTING CUTTING ANGLE
WARNING
Never adjust cutting assembly with engine running.
WARNING
A
Hedge clipper blades are sharp. Always wear gloves when
adjusting cutting assembly, otherwise serious injury may result.
WARNING
DO NOT stand hedge clipper on end when adjusting cutting angle,
otherwise serious injury may result
1.
Place unit on a flat clear area. Assure stop switch is in the “STOP”
position.
2.
Pull out indexing ring (A), and turn ¼ turn to lockout position.
3.
Turn hedge clipper ¼ turn so that indexing ring faces downward.
4.
Release hand-guard blade lock (B) with right hand, while holding
blade-adjustment handle (C) with left hand.
5.
Rotate blades to desired cutting position and hold in place.
6.
Turn indexing ring ¼ turn to lock blade in place.
WARNING
Gear case assembly becomes HOT during use. Always grip
assembly at blade-adjustment handle when making cutting angle
adjustments, otherwise serious injury may result.
IMPORTANT
Always install blade cover, and return cutting assembly to folded/
locked position for travel/storage.
B
B
C
10
ROTATE CUTTER ASSEMBLY
Always use the unit from the right-hand side of your body – NEVER
from the left side. Rotate cutter assembly 180 degrees on driveshaft in
order to avoid cutting directly above your head, and to avoid contact
with hot muffler.
1.
Loosen gearcase clamping screw (A), hand guard clamping screw
(B), and remove gearcase locating screw (C).
2.
Rotate cutter assembly 180-degrees on driveshaft until locating
hole in driveshaft is visible through locating hole in gearcase.
3.
Install gearcase locating screw (C), and securely tighten all
hardware.
B
C
WARNING
During operation, the complete unit, especially the drive shaft
housing and gearcase may become too hot to touch. Avoid
contact when rotating cutter assembly.
HEDGE TRIMMING
1.
2.
3.
Always grip throttle handle with right hand and support handle
with left hand while trimming.
Hold trimmer firmly and squeeze throttle trigger to accelerate
engine.
Tilt trimmer so cutting teeth are angled slightly toward the hedge
or shrub and proceed to cut.
WARNING
Never remove hands from unit when blades are moving.
WARNING
The engine continues running even when the blades have stopped
due to an obstruction. If this occurs, stop the engine, disconnect
ignition cable and remove the obstruction.
A
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
MAINTENANCE
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing
service. Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will
help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to
take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO
dealer for repairs.
SKILL LEVEL
Level 1 =
Level 2 =
Easy to do. Common tools may be required.
Moderate difficulty. Some specialized tools may be required.
MAINTENANCE INTERVALS
Component/System
Maintenance Procedure
Cutting Blades
Drive Shaft
Gear Housing
Screws/Nuts/Bolts
Oil/Clean
Grease
Grease
Inspect/Tighten/Replace
Skill Level
1
1
1
1
LUBRICATION
Blades
Level 1
Tools Required: Clean rag, brush, oil can
Parts Required: 20W Engine Oil (lubrication), 50-50 mixture of
kerosene and 20W oil (cleaning).
WARNING
Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.
1.
2.
3.
4.
Brush loose debris from blade and coat both sides of blade with the
50-50 cleaning mixture.
Allow cleaning mixture to soften the remaining gummy residue then wipe it
from the blade.
Apply clean oil to the entire length of the blade. Be certain the blade bolts
are lubricated.
Wipe excess oil from the blade before putting the unit back in service.
Frequency
Before each use
Every 25 hours of use
Every 15-25 hours of use
Before each use
11
12
Gear Housing
Level 1.
Tools required: Grease Gun, Rag.
Parts required: POWER BLENDXTM 14 oz. Cartridge P/N 91015
Grease or Lithium-based Grease.
1.
Clean dirt from grease fittings (A).
2.
Carefully pump grease in each fitting. DO NOT force grease.
Too much pressure will force grease past seals and cause damage.
Apply 1-2 pumps of grease every 15-25 hours of operation.
A
A
Lower Drive Shaft Assembly
Level 1
NOTE
Drive shaft should be greased every 25 hours of operation.
Tools required: 4 mm hex wrench, 8mm open end wrench, clean rag,
small brush.
Parts required: POWER BLENDXTM 14 oz. cartridge P/N 91015 or
Lithium-based Grease.
WARNING
Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.
1.
Carefully remove locating screw (A) and loosen clamping screw (B).
Remove the flex drive shaft assembly from the gear housing.
2.
Pull the drive shaft (C) from the drive shaft assembly, and wipe
clean. Re-coat with a thin coating [1/2 oz. (15 ml)] of grease.
3.
Slide the flex shaft back into the drive shaft assembly, being careful
not to get dirt on the flex shaft.
4.
Align the locating screw hole in gear case with the locating hole in
drive shaft assembly, install and tighten locating screw (A), and
tighten clamping screw (B).
IMPORTANT
Flat edge of washer (D) must be against drive shaft.
A
D
B
C
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
SHARPENING BLADES
Level 3.
Tools required: Flat file, screwdriver
Parts required: None
WARNING
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.
1.
Disconnect spark plug wire from spark plug.
2.
Slide blades to allow file clearance using slots (A) on bottom of
blades. Do not pry against cutting edges.
3.
Follow the original shape, and file each cutting edge carefully to
avoid damage to adjacent teeth. Maintain 6 mm (.25 in.) radius at
base of each tooth.
IMPORTANT
If a power grinder is used, DO NOT allow blade to over heat.
4.
Lubricate blades. See "Lubrication."
5.
Connect spark plug wire.
A
A
6mm (.25 in.) Radius
45º
13
14
BLADE ADJUSTMENT
Level 2.
Tools required: (2) 10 mm Sockets & Extensions
Parts required: None
WARNING
Hedge clipper blades are very sharp. Touching them may lead to
severe personal injury. Use a socket and extension when adjusting blade bolts or blade locknuts in order to keep hands at a safe
distance from sharp blades.
1.
2.
Tighten blade bolts (A) until snug, then loosen blade bolts 1/2
turn.
Hold blade bolts (A) from turning using 10 mm socket & Extension, and tighten blade lock nuts (B) with other 10 mm Socket &
Extension.
NOTE
Locking ability of Hedge Clipper blade lock nuts will diminish
each time they are removed. Replace if turning resistance is not
felt when installing locknuts.
B
A
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
STORAGE
IMPORTANT
Always store and transport hedge clippers in a stable position.
Support gear case and cutting blades to prevent excessive flexing
which may cause damage to the cutting attachment. Always
install blade cover when transporting or storing unit.
1.
Clean and lubricate cutting blades and gear case.
2.
Sharpen cutting blades as required.
3.
Apply a light coating of clean 20W engine oil along entire length of
blades and on blade bolts.
4.
Install blade cover onto hedge clipper cutting blades.
5.
Store hedge clipper attachment in a dry, dust free place out of the
reach of children, using supplied storage hook.
Storage Hook Installation
1.
Insert small end of hook into locating hole on attachment shaft.
2.
Slide plastic cap onto end of attachment shaft.
SPECIFICATIONS
PAS Articulating Hedge Clipper Attachment
Length ------------------------------------------------------- 1016 mm (40.0 in.)
Attachment Width ----------------------------------------- 132 mm (5.2 in.)
Height ------------------------------------------------------- 127 mm (5.0 in.)
Weight ------------------------------------------------------ 2.76 kg. (6.08 lb.)
Gear Case Ratio -------------------------------------------- 4.072 : 1
Cutter -------------------------------------------------------- Double Reciprocating Blade - Double Edge
Effective Length ----------------------------------------- 464 mm (18.3 in.)
Pitch ------------------------------------------------------- 35 mm (1.4 in.)
Maximum Diameter Cut
Soft Material ---------------------------------------------- 25.4 mm (1 in.)
Woody Material ------------------------------------------ 13 mm (1/2 in.)
15
SERVICING INFORMATION
PARTS/SERIAL NUMBER
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the unit with you. You can find these
numbers on the engine housing. For future reference, write them in the
space provided below.
Model No. _____________ SN. ____________
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30 am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
DEALER?
Call
1-800-432-ECHO
or
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
WARRANTY REGISTRATION
You may register your Echo equipment using the warranty registration
card or register on-line at www.echo-usa.com. Registering provides a
direct link between you and ECHO if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
www.echo-usa.com.
Operator's and Parts Manuals are available by:
• Downloading free from www.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit,
part number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047-1564
www.echo-usa.com
S06700001001/S06700999999
Download PDF

advertising