Echo 99944200513 Cultivator User Manual

x7722271404 / x772000164
99944200513
Cultivator Pro AttachmentTM Series
FOR MODELS: SRM-2100SB, 2400SB, 210SB, 211SB, 225SB,
260SB, 261SB, PAS-2100, 2400, 2601, 210, 211, 225, 225VP,
225VPB, 230, 231, 260, 261, 265, 266, 280
Operator’s Manual
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to do so
could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7702093305
© 08/2013 ECHO Inc.
TABLE OF CONTENTS
99944200513
TABLE OF CONTENTS
Table of Contents .............................................................................................................................. 2
Introduction ........................................................................................................................................ 3
The Operator’s Manual ................................................................................................................ 3
Servicing Information ......................................................................................................................... 3
Parts/Serial Number..................................................................................................................... 3
Service ......................................................................................................................................... 3
Echo Consumer Product Support ................................................................................................ 3
Warranty Registration .................................................................................................................. 3
Additional or Replacement Manuals ............................................................................................ 3
Safety................................................................................................................................................. 4
Manual Safety Symbols and Important Information ..................................................................... 4
International Symbols .................................................................................................................. 5
Personal Condition and Safety Equipment .................................................................................. 5
Equipment.................................................................................................................................... 8
Description......................................................................................................................................... 9
Contents .......................................................................................................................................... 10
Assembly ......................................................................................................................................... 11
Power Head Shaft/Lower Shaft Assembly ................................................................................. 11
Operation ......................................................................................................................................... 12
Operating Techniques................................................................................................................ 12
Maintenance .................................................................................................................................... 15
Skill Levels ................................................................................................................................. 15
Maintenance Intervals................................................................................................................ 15
Lubrication ................................................................................................................................. 15
Drive Shaft (Lower) ................................................................................................................... 16
Storage ............................................................................................................................................ 17
Storage Hook Installation........................................................................................................... 17
Specifications................................................................................................................................... 18
Warranty Statements ....................................................................................................................... 19
Notes ............................................................................................................................................... 21
2
X7702093305
© 08/2013 ECHO Inc.
99944200513
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual. You will find it easy to use and full of helpful
operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future
reference, write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to
4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
www.echo-usa.com or by filling out the warranty registration card supplied with your unit. Registering your
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
Additional or Replacement Manuals
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at
www.echo-usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047
(800-673-1558). Always check the ECHO Web Site for updated information.
X7702093305
© 08/2013 ECHO Inc.
3
SAFETY
Safety Videos are available from your Echo dealer. A $5.00
shipping charge will be required for each video.
99944200513
For more information
scan this QR code.
SAFETY
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling,
starting and stopping instructions.
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
4
X7702093305
© 08/2013 ECHO Inc.
99944200513
SAFETY
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Warning, See
Operator’s
Manual
Safety/Alert
DO NOT USE
BLADES - Line
Head Only
Wear eye, ear
and head
protection
Finger Severing
Plan retreat
pathfromfalling
objects
Wear hand
and foot
protection
Rotating Cutting
Attachment
AVOID KICKOUT.
Keep bystanders at least 15 meters
(50 feet) away.
Wear Face
Shield
Wear slip
resistant foot
wear
Beware Thrown Objects
Wear Eye Protection
Keep feet
away from
blade
Do not operate
closer than 15 M
(50 ft.) from
electrical hazards.
Keep
bystanders at
least 15 meters
(50 feet) away
Thrown
objects
Keep bystanders and helpers
away 15 m (50 ft.).
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eye protection that meets ANSI Z87.1, CE, or CSA Z94.3 requirements must be worn whenever you operate
the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the
transmission of machine vibration to your hands.
Breathing Protection
Wear a facemask to protect against dust.
X7702093305
© 08/2013 ECHO Inc.
5
SAFETY
99944200513
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work
for early morning or late afternoon hours when temperatures are cooler.
The ignition components of this machine generate an electromagnetic field during operation which
may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of ECHO
products by anyone who has a pacemaker.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon,
which affects the fingers of certain individuals, may be brought
about by exposure to vibration and cold. Exposure to vibration
and cold may cause tingling and burning sensations, followed
by loss of color and numbness in the fingers. The following
precautions are strongly recommended, because the minimum
exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and
also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held
power equipment is not required.
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling,
consult your physician before further exposing yourself to cold and vibration.
6
X7702093305
© 08/2013 ECHO Inc.
99944200513
SAFETY
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the
fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those
areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme
RSI condition is Carpal Tunnel Syndrome (CTS), which could
occur when your wrist swells and squeezes a vital nerve that
runs through the area. Some believe that prolonged exposure to
vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist
position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
All over head electrical conductors and communications wires can have electricity flow with high
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,
otherwise serious injury or death may result.
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual
for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children
and animals prevented from coming nearer than 15 m (50 ft.)
while the unit is in use.
Keep a Firm Grip
• Always hold throttle handle and support handle with thumbs
and fingers tightly encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not
work in odd positions or on ladders. Do not over reach.
X7702093305
© 08/2013 ECHO Inc.
7
SAFETY
99944200513
Avoid Hot Surfaces
• During operation, the drive shaft housing and attachment
bearing housing may become very hot, too hot to touch. Avoid
contact during and immediately after operation.
Equipment
Use this attachment with ECHO approved models only. Serious injury may result from the use of this
attachment combined with a non approved ECHO product.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect shield for damage and that shield is securely in place. Replace if sjield is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe operating condition.
• The cultivator gear housing is designed for ECHO recommended tines. Do not modify the gear housing for
any other purpose or replace tines with other type or size.
Note: ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories
which have not been tested and approved by ECHO.
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
◆
◆
◆
8
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
NEVER reach into any opening while the engine is running. Moving parts may not be visible through
openings.
X7702093305
© 08/2013 ECHO Inc.
99944200513
DESCRIPTION
DESCRIPTION
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
7
1
6
2
4
3
4
Shaft Label
5
1. DRIVE SHAFT ASSEMBLY - Contains a specially designed liner and the flexible drive shaft.
2. SHIELD - Attached to deflect debris away from operator and reduce accidental contact with tines.
3. HUB - Separately attached to axle ends by clevis pin and spring pin. Tines bolt to hubs.
4. TINES - Identical on right and left side from operator's position. See page 12 for optional settings.
5. GREASE ACCESS BOLT - Apply grease to gear housing every 25 hours of use.
6. GEAR HOUSING - Houses gears and ball bearings for driving tines.
7. SERIAL NUMBER LABEL - Also serves as insertion line when drive shaft is properly engaged.
X7702093305
© 08/2013 ECHO Inc.
9
CONTENTS
99944200513
CONTENTS
The ECHO product you purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
____ - 1 - PAS Cultivator Attachment
____ 1 - Operator’s Manual
X7722271404 / X772000164
99944200475
Cultivator Pro
Attachment Series
____ 1 - Warranty Registration Card
____ 1 - Storage Hook Assembly
Operator’s Manual
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur.
The engine exhaust from this product contains chemicals known to the State of California to cause cancer.
birth defects or other reproductive harm.
Read rules for safe operation and instructions carefully. ECHO provides an Operator’s Manual
and a Safety Manual. Both must be read and understood for proper and safe operation.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7722271404 / X772000164
© 4/2011 ECHO Inc.
10
X7702093305
© 08/2013 ECHO Inc.
99944200513
ASSEMBLY
ASSEMBLY
Power Head Shaft/Lower Shaft Assembly
Do not perform maintenance or assembly procedures with engine running.
Parts Required:
PAS or SRM-SB Power Head w/Shaft & Coupling
1. Set Power Head/Shaft Assembly on a level surface.
B
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn
to lock-out position.
D
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
5. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages the square upper drive shaft socket.
E
C
A
Note: Earlier model Power Heads may have shorter couplings.
Short couplings fit flush to decal point (E). New couplings
are 4-3/4 in. long, and fit flush to line (C).
Note: Lower bearing housing and head assembly must be in line with the engine.
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower
shaft hole. Insure locator pin is fully engaged by twisting
lower drive shaft. Locator pin should snap flush in coupler.
Full engagement will prevent further shaft rotation.
D
C
7. Secure lower shaft assembly to coupler by tightening
clamping knob (D).
X7702093305
© 08/2013 ECHO Inc.
11
OPERATION
99944200513
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a completestop before removing obstructions, clearing debris, or servicing unit. Allow
unit to cool before performing service.
Operating Techniques
• When engine starts tines may rotate. Warn fellow workers and keep children and pets from coming nearer
than 4.5 m (15 ft.).
◆
◆
◆
◆
Always operate cultivator with both hands.
Always stop engine when transporting unit to or between
work areas..
Do not perform maintenance procedures, unclog or clean
cultivator tines while engine is running.
Do not operate the cultivator above ground level or near
feet.
◆
Do not allow the tines to contact large obstructions which
may cause kickback and loss of control..
◆
Failure to follow these warnings may result in serious injury.
12
X7702093305
© 08/2013 ECHO Inc.
99944200513
OPERATION
1. The tilling width of the cultivator is approximately 165 mm
(6.5 in.). Place cultivator in area to be tilled, hold unit firmly
with left hand on front grip and right hand on rear grip and
gradually engage throttle trigger. Guide the cultivator
allowing the tines to pullforward. The soil hardness will
control tilling speed.
2. The cultivator attachment is capable of tilling in the forward
or reverse direction. For deep soil tilling, till forward then
lightly pull unit rearward allowing the tines to make a deeper
cut into the soil. Deep soil cultivating can also be enhanced
by repositioning the tines. (Refer to Tine Setting).
3. To raise or aerate the soil, tilt engine closer to the ground
which will raise cultivator tines higher relative to the soil
surface.
Do not operate cultivator underwater. The gear housing is not
sealed and water will wash away lubrication, damaging gears,
bearings, and seals.
Resetting Tines for Deep Cultivation
The tines are factory assembled with blade ends offset for
standard cultivation. For deep cultivation, the left tine (viewed
from the operator's position) must be repositioned on the hub
aligning the left and right tine blade ends directly across from
each other.
X7702093305
© 08/2013 ECHO Inc.
13
OPERATION
99944200513
1. Remove three (3) bolts (A) mounting left tine to hub. The
bolts will be mounted in hole labeled (1).
A
2. Rotate tine counter clockwise and position hole labeled (2)
over hub mounting holes. The tine blade ends should be
aligned directly opposite each other.
3. Install and tighten bolts.
14
X7702093305
© 08/2013 ECHO Inc.
99944200513
MAINTENANCE
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
COMPONENT/SYSTEM
MAINTENANCE
PROCEDURE
SKILL
LEVEL
Interval
Drive Shaft
Grease
1
Every 25 hours of use [1]
Gear Housing
Grease
1
Every 25 hours of use [2]
Gear Housing/Tines
Clean
1
Dailey or Every 4 hours
Screws/Nuts/Bolts
Inspect/Tighten/Replace
1
Before Each Use
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
[1] Apply POWER BLENDXTM grease.
[2] Apply Lithium-based EP00 Grease every 25 hours of use.
Lubrication
Level 2.
Parts Required:
Lithium-based EP00 Grease for gearcase;
POWER BLENDXTM 8 oz. or Lithium Base
Grease for driveshaft
Gear Housing
1. Clean all loose debris from gear box.
2. Remove plug (C) and check level of grease.
X7702093305
© 08/2013 ECHO Inc.
15
MAINTENANCE
3. Add grease if necessary. DO NOT over-fill.
4. Install screw plug (C).
99944200513
D
A
B
C
Drive Shaft (Lower)
1. Loosen gear housing mounting bolt (A) and remove gear
housing locator screw (B).
2. Pull gear box from drive shaft housing. Shield will remain on
drive shaft.
3. Pull flexible cable from the drive shaft housing, wipe clean
and re-coat with a thin coating [15 ml (1/2 oz.)] of grease.
4. Slide the flexible cable back in the drive housing. DO NOT
get dirt on the flex cable.
5. Assemble gear housing onto drive shaft correctly matching gear housing to shield cutout (D).
6. Install and tighten locator screw (B).
7. Tighten gear housing mounting bolt (A).
16
X7702093305
© 08/2013 ECHO Inc.
99944200513
STORAGE
STORAGE
1. Clean cultivator attachment.
Do not immerse this attachment in water. Water will enter gear
housing and damage gears, bearings and seals..
2. Apply thin coating of oil to metal parts to prevent rust.
3. Lubricate lower shaft assembly with lithium grease.
4. Store cultivator attachment in a dry, dust free place, out of
the reach of children, using supplied storage hook.
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment
shaft.
2. Slide plastic cap onto end of attachment shaft.
X7702093305
© 08/2013 ECHO Inc.
17
SPECIFICATIONS
99944200513
SPECIFICATIONS
MODEL
99944200513
Length
895 mm (35.2 in.)
Width
162 mm (6.4 in.)
Height
211 mm (8.3 in.)
Weight
1.94 kg (4.29 lb.)
Blade Diameter
216 mm (8.5 in.)
Cultivating Width
160 mm (6.3 in.)
Cultivator Mounting Bore
25.0 mm (0.98 in.)
Coupling Square Hole
5.4 x 5.4 mm (0.21 x 0.21 in.)
Gear Reduction Ratio
46.15:1
Gear Case Capacity
38 grams (1.34 oz.)
Gear Case Lubrication
Lithium-based grease
Drive Shaft Lubrication
POWER BLENDXTM
18
X7702093305
© 08/2013 ECHO Inc.
99944200513
WARRANTY STATEMENTS
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
!"#$
%!"#$
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
& 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for from
date of purchase.
EXCEPTIONS:
& '*
+/
9"
are warranted for the of the product on parts only.
& "
*
producing use will be covered for failures due to defects in material or workmanship for a period of from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
& !"#$:
#
;
manual for string head installation and maintenance instructions.
& < =* >$<99<"#/!?9 !@! COMMERCIAL APPLICATION
& 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one from the date of purchase.
& 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two from the date of purchase.
EXCEPTIONS:
& '*
+/
9"
are warranted for the of the product on parts only.
& "
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
& !"#$:
#
;
manual for string head installation and maintenance instructions.
& < =* >$<99<"#/!?9 !@! RENTAL APPLICATION - 90 DAYS WARRANTY
&B
GJ
!"#$
K:N
>$XB"9Y<<?9Z>!@$X section of
this warranty statement for [\J]
X7702093305
© 08/2013 ECHO Inc.
19
WARRANTY STATEMENTS
99944200513
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
&GJ*
*
&^J*
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. !"#$%!&()* *@$*
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
&
:
*that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. !"#$ > =
{9* $ meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
&
X
[]
|G
. Only use gasoline which
contains |G
. Gasohol which contains a +
6+7+\J}
[
]\~}/9=![]
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
&
!
+
&
X
engine speeds as listed in your operator’s manual.
&
$


&
X
&
X
of unauthorized attachments.
&
@
€

manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
&
'**
%!"#$
warranty period.
&
"
parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
&
B €
$!/ $
Manuals.
&
$
screen.
&
<ƒ
[^J]
ƒ
ƒ
&
X

with recommended grease or oil change intervals.
&
X
#!X?„<"® beyond recommended capacity.
&
X
+
&
<
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COMZ
%
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
€
9
!"#$
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
9
'@9?!'$<><9@"B:<>B>$!
OR USE and any implied warranty of MERCHANTABILITY!"#$
€
9
9
!"#$
99922201032
11/18/2011
20
X7702093305
© 08/2013 ECHO Inc.
99944200513
NOTES
NOTES
X7702093305
© 08/2013 ECHO Inc.
21
NOTES
22
99944200513
X7702093305
© 08/2013 ECHO Inc.
99944200513
X7702093305
© 08/2013 ECHO Inc.
NOTES
23
ECHO, INCORPORATED
24
400 Oakwood Road
Lake Zurich, IL 60047
www.echo-usa.com
S06900001001/S06900999999