Echo EDR-210 Remote Starter User Manual

OPERATOR’S MANUAL
ENGINE DRILL
EDR-210
WARNING
READ INSTRUCTIONS CAREFULLY AND FOLLOW RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
ECHO, INCORPORATED
400 Oakwood Road, Lake Zurich, Illinois 60047-1564
Phone : 847-540-8400
X750-004 57 6
X750409-3506
Printed in Japan 1305Bm 1507 ES
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry
products, and
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do
this type of work. To reduce your exposure to these chemicals: work in a
well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic
particles.
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
CONTENTS
Introduction ............................................................................................................................................. 1
Safety and Special Information ............................................................................................................... 1
Decals and symbols ................................................................................................................................ 1
Safety ...................................................................................................................................................... 2
Operating Techniques ............................................................................................................................. 5
Description .............................................................................................................................................. 6
Assembling .............................................................................................................................................. 7
Operation ................................................................................................................................................ 7
Maintenance and Care ............................................................................................................................ 11
Trouble shooting ...................................................................................................................................... 12
Maintenance ............................................................................................................................................ 13
Storage .................................................................................................................................................... 15
Specifications .......................................................................................................................................... 16
Warranty statements ............................................................................................................................... 17
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
Copyright © 2002
All Rights Reserved.
INTRODUCTION
ECHO Engine Drill EDR-210 is a lightweight, high
performance, two-stroke engined unit designed for
drilling.
WARNING
IMPROPER USE OR CARE OF THIS UNIT, OR
FAILURE TO WEAR PROPER PROTECTION
CAN RESULT IN SERIOUS INJURY.
READ AND UNDERSTAND THE RULES FOR
SAFE OPERATION AND ALL INSTRUCTIONS
IN THIS MANUAL.
This Manual provides the information necessary
for operation and maintenance.
SAFETY AND SPECIAL INFORMATION
CIRCLE AND SLASH SYMBOL
DANGER
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or
fatal injury.
The safety alert symbol accompanied by the
word “DANGER” calls attention to an act or
condition which WILL lead to serious
personal injury or death if not avoided.
NOTE
WARNING
This enclosed message provides tips for use,
care and maintenance of the unit.
The safety alert symbol accompanied by the
word “WARNING” calls attention to an act or
condition which CAN lead to serious
personal injury or death if not avoided.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
CAUTION
Throughout this manual and on the product itself,
you will find safety alters and helpful, information
messages preceded by symbols or key words.
The following is an explanation of those symbols
and key words and what they mean to you.
The safety alert symbol accompanied by the
word “CAUTION” calls attention to an act or
condition which may lead to minor or
moderate personal injury if not avoided.
DECALS AND SYMBOLS
Symbol form/shape
Symbol description/application
Symbol form/shape
Symbol description/application
Carefully read the operator’s
manual
Wear eyes, ears and head
protection
Beware of high-temperature
areas
Finger severing
1
SAFETY
WARNING
WARNING
ENGINE DRILL USERS RISK INJURY TO
THEMSELVES AND OTHERS IF THE ENGINE
DRILL IS USED IMPROPERLY, AND/OR
SAFETY PRECAUTIONS ARE NOT
FOLLOWED. PROPER CLOTHING AND
SAFETY GEAR MUST BE WORN WHEN
OPERATING ENGINE DRILL.
ALWAYS STOP THE ENGINE WHEN A DRILL
JAM OCCURS. DO NOT ATTEMPT TO
REMOVE AN OBJECT CAUSING A DRILL
JAM IF THE ENGINE IS RUNNING. PHYSICAL
INJURY CAN OCCUR IF A DRILL JAM IS
REMOVED AND THE DRILLS START
MOVING.
•
OPERATOR SAFETY
•
Read this Engine drill Operator’s Manual
carefully. Be sure you understand how to
operate this unit properly before you use it.
•
Be familiar with all the controls and the proper
use of the machine.
•
Wear proper clothing to protect legs and other
exposed parts of your body.
•
Wear non-skid sole shoes. Do not wear opentoed shoes or operate unit while bare footed.
•
Wear eye and hearing protection devices.
•
Use caution when handling fuel. Put the caps
back tightly on both the fuel can and the
engine drill fuel tank.
Move at least 3 m (10 feet) from the re-fueling
point and be sure there is no leakage of fuel
from the fuel tank cap or the fuel system before
starting the engine.
•
WARNING
USE A FIRM GRIP WITH THUMBS AND
FINGERS ENCIRCLING THE HANDLES. A
FIRM GRIP WILL HELP YOU KEEP
CONTROL OF THE ENGINE DRILL. NEVER
OPERATE THE ENGINE DRILL ONLY ONE
HAND OR BODILY INJURY CAN OCCUR.
•
Start the unit on the ground with the throttle set
at idle. Do not start if the drills are obstructed
by the ground or any other object.
•
Never allow children to use the machine.
•
Do not allow anyone to hold the material you
are drilling.
•
Keep a firm grip on the engine drill with both
hands, one hand on the front handle, the other
hand on the rear handle.
Always carry the engine drill with the engine
stopped and the HOT muffler away from your
body.
PROTECTIVE EQUIPMENT
Operate this gasoline powered engine
equipment in a well-ventilated area only.
•
Do all drilling at full throttle speed. Drilling at
less at than full speed can damage the clutch
by allowing it to slip.
2
•
Always wear eye protection goggles that meet
ANSI Z87.1 standards.
•
Wear hearing protection.
ECHO recommends that hearing protection be
worn at all times.
•
Dress properly! Do not wear loose clothing or
jewellery, they can be caught in moving parts.
Use of sturdy gloves, non-skid footwear, and
safety glasses is recommended.
•
While operating the machine always be sure of
a secure position.
•
Wear non-slip, heavy-duty work gloves to
improve your grip on the engine drill handles.
The gloves also help reduce the transmission
of machine vibrations to your hands.
WARNING
PRECAUTION AGAINST VIBRATION
AND COLD
IT IS BELIEVED THAT A CONDITION
CALLED RAYNAUD’S PHENOMENON,
WHICH AFFECTS THE FINGERS OF
CERTAIN INDIVIDUALS MAY BE BROUGHT
ABOUT BY EXPOSURE TO VIBRATION AND
COLD. EXPOSURE TO VIBRATION AND
COLD MAY CAUSE TINGLING AND
BURNING SENSATIONS FOLLOWED BY
LOSS OF COLOR AND NUMBNESS IN THE
FINGERS. THE FOLLOWING PRECAUTIONS
ARE STRONGLY RECOMMENDED BECAUSE
THE MINIMUM EXPOSURE WHICH MIGHT
TRIGGER THE AILMENT IS UNKNOWN.
PROTECTING OTHERS
Spectators, children, fellow workers and animals
must be warned to come no nearer than 4.6 m (15
feet) while the engine drill is in use.
People working in the area near you should wear
the same protective equipment as the operator.
PHYSICAL CONDITION
Your judgement and dexterity may be impaired if
you are ill or have taken alcohol or other
substances known to affect the way you would
normally function.
• KEEP YOUR BODY WARM, ESPECIALLY
THE HEAD, NECK, FEET, ANKLES, HANDS
AND WRISTS.
• MAINTAIN GOOD BLOOD CIRCULATION
BY PERFORMING VIGOROUS ARM
EXERCISES DURING FREQUENT WORK
BREAKS AND ALSO BY NOT SMOKING.
• LIMIT THE HOURS OF OPERATION. TRY
TO FILL EACH DAY WITH JOBS WHERE
OPERATING THE ENGINE DRILL OR
OTHER HAND-HELD POWER EQUIPMENT
IS NOT REQUIRED.
• IF YOU EXPERIENCE DISCOMFORT,
REDNESS AND SWELLING OF THE
FINGERS FOLLOWED BY WHITENING AND
LOSS OF FEELING, CONSULT YOUR
PHYSICIAN BEFORE FURTHER EXPOSING
YOURSELF TO COLD AND VIBRATION.
Painful or numb fingers?
See your doctor
3
Repetitive Stress Injuries
It is believed that over-using the muscles and
tendons of the fingers, hands, arms and shoulders
may cause soreness, swelling, numbness,
weakness and extreme pain in those areas.
Certain repetitive hand activities may put you at a
high risk for developing a Repetitive Stress Injury
(RSI). An extreme RSI condition is Carpal Tunnel
Syndrome (CTS), which could occur when your
wrist swells and squeezes a vital nerve that runs
through the area. Some believe that prolonged
exposure to vibration may contribute to CTS.
CTS can cause severe pain for months or even
years. To reduce the risk of RSI/CTS, do the
following:
4
•
Avoid using your wrist in a bent, extended or
twisted position. Instead try to maintain a
straight wrist position. Also, when grasping,
use your whole hand, not just the thumb
and index finger.
•
Take periodic breaks to minimize repetition
and rest your hands.
•
Reduce the speed and force with which you do
the repetitive movement.
•
Do exercise to strengthen the hand and arm
muscles.
•
See a doctor if you feel tingling, numbness or
pain in the fingers, hands, wrists or arms.
The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage
can be prevented.
OPERATING TECHNIQUES
•
When starting to drill, run the engine at full
throttle.
•
When transporting or storing the machine
always remove the drill bit.
•
To reduce fire hazard keep engine and silencer
free of debris, leaves or excessive grease.
•
Handle drill with care, contacting with drills
may cause injury.
WARNING
BEFORE DRILLING, BE SURE TO READ AND
UNDERSTAND THE ENTIRE OPERATOR’S
MANUAL TO AVOID THE CHANCE OF
SERIOUS INJURY.
•
Do not force the drills and only move as
quickly as the drills will allow.
•
Stop the engine and disconnect from ignition
cable before: - cleaning or when clearing a
blockage; checking, maintenance or working
on the machine.
•
Handle fuel with care; it is highly flammable.
Never add fuel to a machine with a running or
hot engine.
•
Do not attempt to repair the machine unless
you are qualified to do so.
•
Do not operate the machine with a damaged or
excessively worn drill bit.
•
Always ensure all handles and guards are
fitted when using the machine. Never attempt
to use an incomplete machine or one fitted with
an unauthorized modification.
5
DESCRIPTION
2
1
3
4
Part Number X505-002310
14
15
13
Part Number X505-002570
12
Part Number X505-002310
11
10
Part Number X505-002570
9
6
7
8
5
* If a decal cannot be read, a new one can be
ordered from your ECHO dealer.
1. Operator’s manual - Included with unit. Read
before operation and keep for future reference
to learn proper, safe operating techniques.
2. Throttle trigger - Device activated by the
operator’s finger, for controlling the engine
speed.
3. Rear handle - Handle located furthest from the
drill bit.
4. Silencer cover
5. Drill bit - Not included with unit.
6. Chuck
7. Shift lever
8. Front handle - Handle located on the front
gear case.
9. Fuel tank - Contains fuel and fuel filter.
10. Fuel tank cap - For closing the fuel tank.
11. Air cleaner cover - Covers air filter.
12. Starter handle - Pull handle to start the
engine.
13. Throttle trigger lockout - Device that
prevents the accidental operation of the throttle
trigger until manually released.
14. Ignition switch - Device for allowing the
engine to be started and stopped.
15. Spark plug
6
ASSEMBLING
FRONT HANDLE
•
Washer
Front handle
Insert the front handle to the machine, and turn
clockwise.
(TIGHTEN THE SCREW FIRMLY)
- To operate front handle with right hand,
remove right plug then reverse sides when
installing handle and plug.
DRILL BIT
•
Insert the drill bit (not provided with unit) until it
reaches the bottom of the chuck, then back it
out slightly; tighten the chuck laws evenly and
completely.
IMPORTANT
Use drill bits suited for the material being
drilled and for the depth of hole required.
Plug
Chuck Drill bit
(Tighten three points evenly)
OPERATION
CHECK UP OF NUTS AND OTHER
HARDWARES
WARNING
ALTERNATIVE FUELS, SUCH AS E-20 (20 %
ETHANOL), E-85 (85 % ETHANOL) OR ANY
FUELS NOT MEETING ABOVE
REQUIREMENTS ARE NOT APPROVED FOR
USE IN ECHO 2-STROKE GASOLINE
ENGINES.
USE OF ALTERNATIVE FUELS MAY CAUSE
PERFORMANCE PROBLEMS, LOSS OF
POWER, OVERHEATING, FUEL VAPOR
LOCK, AND UNINTENDED MACHINE
OPERATION, INCLUDING, BUT NOT LIMITED
TO, IMPROPER CLUTCH ENGAGEMENT.
ALTERNATIVE FUELS MAY ALSO CAUSE
PREMATURE DETERIORATION OF FUEL
LINES, GASKETS, CARBURETOR AND
OTHER ENGINE COMPONENTS.
•
FUEL STATEMENT
GASOLINE - Use 89 Octane [(R+M)/2] (mid grade
or higher) gasoline or gasohol known to be good
quality.
Gasohol may contain up to 10 % Ethyl (grain)
alcohol or 15 % MTBE (methyl tertiary-butyl ether).
Gasohol containing methyl (wood) alcohol is NOT
approved.
TWO-STROKE OIL - A two-stroke engine oil meeting
ISO-L-EGD (ISO/CD 13738) and JASO M345-FC/FD
Standards must be used. ECHO brand premium
Power Blend X™ Universal 2-Stroke Oil meets these
standards. Engine problems due to inadequate
lubrication caused by failure to use an ISO-L-EGD
(ISO/CD 13738) and JASO M345-FC/FD certified oil,
such as ECHO premium Power Blend X™, will void
the two-stroke engine warranty. (Emission related
parts only are covered for two years, regardless of
two-stroke oil used, per the statement listed in the
Emission Defect Warranty Explanation.)
Fuel Mix Chart 50 : 1
US.
Gasoline
Gallons
1
2
5
Oil
US. fl. oz.
2.6
5.2
12.8
Check up loose nuts, bolts and screws before
using the unit every day.
METRIC
Gasoline
Oil
L
mL
4
80
8
160
20
400
7
IMPORTANT
• ECHO premium Power Blend X™ Universal
2-Stroke Oil may be mixed at 50 : 1 ratio for
application in all ECHO engines sold in the
past regardless of ratio specified in those
manuals.
• Use of unmixed, improperly mixed, or fuel
older than 90 days, (stale fuel), may cause
hard starting, poor performance, or severe
engine damage and void the product
warranty. Read and follow instructions in
the Storage section of this manual.
HANDLING FUEL
MIXING INSTRUCTIONS 1. Fill an approved fuel container with half of the
required amount of gasoline.
DANGER
FUEL IS VERY FLAMMABLE. USE EXTREME
CARE WHEN MIXING, STORING OR
HANDLING OR SERIOUS PERSONAL
INJURY MAY RESULT.
• USE AN APPROVED FUEL CONTAINER.
• DO NOT SMOKE NEAR FUEL.
• DO NOT ALLOW FLAMES OR SPARKS
NEAR FUEL.
• FUEL TANKS/CANS MAY BE UNDER
PRESSURE.
ALWAYS LOOSEN FUEL CAPS SLOWLY
ALLOWING PRESSURE TO EQUALIZE.
• NEVER REFUEL A UNIT WHEN THE
ENGINE IS HOT!
• NEVER REFUEL A UNIT WITH THE
ENGINE RUNNING.
• DO NOT FILL FUEL TANKS INDOORS.
ALWAYS FILL FUEL TANKS OUTDOORS
OVER BARE GROUND.
• DO NOT OVERFILL FUEL TANK. IT IS NOT
PERMITTED TO FILL FUEL ABOVE THE
SHOULDER LEVEL OF FUEL TANK. WIPE
UP SPILLS IMMEDIATELY.
• SECURELY TIGHTEN FUEL CAP AFTER
REFUELING.
• INSPECT FOR FUEL LEAKAGE.
IF FUEL LEAKAGE IS FOUND, DO NOT
START OR OPERATE UNIT UNTIL
LEAKAGE IS REPAIRED.
• MOVE AT LEAST 3 M (10 FEET) FROM
REFUELING LOCATION BEFORE
STARTING THE ENGINE.
2. Add the proper amount of two-stroke oil to
gasoline.
3. Close container and shake to mix oil with
gasoline.
4. Add remaining gasoline, close fuel container,
and remix.
IMPORTANT
• Spilled fuel is a leading cause of
hydrocarbon emissions. Some states may
require the use of automatic fuel shut-off
containers to reduce fuel spillage.
• Stored fuel ages.
Do not mix more fuel than you expect to
use in thirty (30) days, ninety (90) days
when a fuel stabilizer is added.
• Stored two-stroke fuel may separate.
ALWAYS shake fuel container thoroughly
before each use.
AFTER USE DO NOT store a unit with fuel in its tank. Leaks can
occur. Return unused fuel to an approved fuel
storage container.
STORAGE Fuel storage laws vary by locality. Contact your
local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight
container. Store in a well-ventilated, unoccupied
building, away from sparks and flames.
Shoulder level
Fuel tank
8
STARTING COLD ENGINE
WARNING
WHEN ENGINE IS STARTED, CONFIRM IF
THERE IS NOT ANY ABNORMAL VIBRATION
OR SOUND. IF THERE IS ABNORMAL
VIBRATION OR SOUND, ASK YOUR DEALER
TO REPAIR.
ON
•
Stand the engine upright on a level surface.
•
Place ignition switch in ON (START/RUN)
position.
•
Push purge bulb 3 to 4 times (or until fuel is
visible in fuel return line).
•
Shift choke lever to close position (START).
•
Pull starter handle until the engine fires.
•
Shift choke lever to full open position, and if
necessary, start the engine again and allow to
warm up before using.
- The clutch engages at approximately 3500
r/min. Therefore the drill bit may rotate at
fast idle engine speed.
Ignition switch
STOP
Throttle trigger
Throttle trigger lockout
Air cleaner
STARTING WARM ENGINE
Purge bulb
Fuel return line
Push
•
Place ignition switch in ON (START/RUN)
position.
•
Pull starter handle until the engine fires.
- Do not use the choke.
Starter handle
STOPPING ENGINE
Choke lever
RUN
(Open)
•
Set throttle trigger in idle position.
•
Place ignition switch in STOP position.
NOTE
When engine does not stop, shift choke lever to
close position.
Check and repair ignition switch before starting
the engine again.
START
(Close)
9
REVERSE ROTATION
Counter
clockwise
(CCW)
Shift lever
Clockwise
(CW)
•
This model is equipped with reverse rotation
mechanism.
•
When drilling, set shift lever down to clockwise
(CW) rotation position.
•
If bit is locked due to deep penetration during
drilling operation, set shift lever up to
counterclockwise (CCW) rotation position and
operate reversed for easy pulling-out.
•
When changing direction of drill rotation,
operate as follows:
- Return engine to idle.
- Engine shift lever to CW or CCW position
with a slight acceleration of the throttle
trigger.
To properly lock the gears in the gear case.
- Do not operate shift lever forcibly when
changing rotation direction.
NOTE
WARNING
• WHEN THE DRILL CAN NOT PULL OUT
FROM THE WOOD, DO NOT TRY TO PULL
OUT THE DRILL BY FORCE.
Do not shift from forward to reverse (or viceversa) while the chuck is turning.
Failure to do so may cause unit damage.
Always release throttle and allow the unit to
return to idle before shifting.
• WHEN CHANGING THE BIT, ENSURE TO
STOP THE ENGINE.
• AFTER A JOB, BIT AND GEAR CASING
MAY BE HEATED, DO NOT TOUCH THEM
WITH BARE HANDS.
Do not stand close to drill or chuck with your
body or clothes while operation.
When drilling, ensure that no power cable or
other obstacle exist.
10
MAINTENANCE AND CARE
AREA
MAINTENANCE
PAGE
BEFORE
USE
Air Filter
Clean/Replace
13
•
Fuel Filter
Inspect/Clean/
Replace
13
•
Spark Plug
Inspect/Clean/
Adjust/Replace
13
•
Carburetor
Adjust
14
Cooling System
Inspect/Clean
15
•
Silencer
Inspect/Tighten/
Clean
15
•
Starter Rope
Inspect/Replace
-
Drills
Inspect/Clean/
Lubricate
-
Fuel Leaks
Inspect
YEARLY
DATE
MAINTENANCE
PERFORMED
•
•
•
13
•
Screws, Bolts and Inspect,
Nuts
Tighten/Replace
-
•
Fuel Line
-
Inspect
MONTHLY
•
IMPORTANT
Time intervals are maximum. Actual use and
your experience will determine the frequency
of required maintenance.
Record dates of monthly and yearly
inspections.
EMISSION DATA
EMISSION CONTROL
PRODUCT EMISSION DURABILITY
(EMISSION COMPLIANCE PERIOD)
The 300 hours emission compliance period is
the time span selected by the manufacturer
certifying the engine emissions output meets
applicable emissions regulations, provided that
approved maintenance procedures are followed
as listed in the Maintenance Section of this
manual.
(EXHAUST and EVAPORATIVE)
EPA 2010 and Later and/or C.A.R.B. TIER III
The emission control system for the engine is EM
(engine modifi cation) and, if the second to last
character of the Engine Family on the Emission
Control Information label (sample below) is "C", "K",
or "T",the emission control system is EM and TWC
(3-way catalyst). The fuel tank/fuel line emission
control system is EVAP (evaporative emissions).
Evaporative emissions for California models may
only be applicable to fuel tanks.
An Emission Control Label is located on the
engine. (This is an example only, information on
label varies by engine family).
11
TROUBLE SHOOTING
Engine -
Trouble
hard to start
does not start
Engine
cranks
Fuel at
carburetor
No fuel
at carburetor
• Fuel filter clogged
• Fuel line clogged
• Carburetor
• Clean or replace
• Clean
• Ask your ECHO dealer
Fuel at
cylinder
No fuel at
cylinder
• Carburetor
• Ask your ECHO dealer
Silencer wet
with fuel
• Fuel mixture is too rich
• Open choke
• Clean/replace air filter
• Adjust carburetor
• Ask your ECHO dealer
Spark at
end of
plug wire
No spark at
end of plug
wire
• Ignition switch off
• Electrical problem
• Turn switch on
• Ask your ECHO dealer
Spark at
plug
No spark at
plug
• Spark gap incorrect
• Covered with carbon
• Fouled with fuel
• Spark plug defective
• Adjust 0.6 to 0.7 mm
(0.024 to 0.028 in)
• Clean or replace
• Clean or replace
• Replace plug
• Internal engine problem
• Ask your ECHO dealer
• Air filter dirty
• Fuel filter dirty
• Fuel vent blocked
• Spark plug
• Carburetor
• Cooling system blocked
• Exhaust port/spark
arrester screen blocked
• Clean or replace
• Clean or replace
• Clean
• Clean and adjust/replace
• Adjust
• Clean
• Clean
Cause
Engine
does not
crank
Engine
runs
Dies or
accelerates poorly
Remedy
WARNING
• ALL ENGINE DRILL SERVICE OPERATIONS, OTHER THAN ITEMS LISTED IN THE
OPERATOR’S MANUAL, SHOULD BE PERFORMED BY AN AUTHORIZED ECHO DEALER.
• FUEL VAPORS ARE EXTREMELY FLAMMABLE AND MAY CAUSE FIRE AND/OR
EXPLOSION. NEVER TEST FOR IGNITION SPARK BY GROUNDING SPARK PLUG NEAR
CYLINDER PLUG HOLE, OTHERWISE SERIOUS PERSONAL INJURY MAY RESULT.
12
MAINTENANCE
AIR FILTER
•
Air filter
Clean before use.
- Remove air cleaner cover and pull out air
filter.
- Lightly brush off dust or wash it in water and
detergent.
- Dry completely before putting it back in
place.
Air cleaner cover
FUEL FILTER
•
Fuel filter
Check periodically.
- Do not allow dust to enter into fuel tank.
- Clogged filter will cause difficulty in starting
engine or poor engine performances.
- Pick up fuel filter through fuel inlet port with
a piece of steel wire or the like.
- When filter is dirty, replace it.
Fuel tank cap
NOTE
CHECK FUEL SYSTEM
Federal EPA regulations require all model year
2012 and later gasoline powered engines
produced for sale in the United States to be
equipped with a special low permeation fuel
supply hose between the carburetor and fuel
tank. When servicing model year 2012 and later
equipment, only fuel supply hoses certified by
EPA can be used to replace the original
equipment supply hose. Fines up to $37,500
may be enforced for using an un-certified
replacement part.
•
Check before every use.
•
After refueling, make sure fuel does not leak or
exude from around fuel pipe, fuel grommet or
fuel tank cap.
•
In case of fuel leakage or exudation there is a
danger of fire. Stop using the machine
immediately and request your dealer to inspect
or replace.
SPARK PLUG
•
Check periodically.
- The standard spark gap is 0.6 to 0.7 mm
(0.024 to 0.028 in).
- Correct spark gap if it is wider or narrower
than the standard gap.
- If the electrodes are coated with carbon
deposits replace with a new spark plug.
Do not sandblast to clean.
Remaining sand will damage engine.
•
Fastening torque = 15 to 17 N • m
(130 to 145 in • lb).
0.6 - 0.7 mm (0.024 - 0.028 in)
IMPORTANT
Do not over tighten plug.
13
REPLACEMENT OF CHUCK
Replacement of chuck should be done in the
following manner:
1. Remove bolt with hexagonal hole fixed in the
driving axle.
2. Insert accessory hexagonal bar (Part Number
895412-20960) into chuck and fix.
3. Fit 19 mm spanner onto driving axle and keep
it fitted.
4. Fit 10 mm box spanner onto the hexagonal bar
and turn it into direction as indicated by an
arrow to remove chuck.
5. Fit a new chuck in the reversed order of
removing.
Box spanner
Spanner (19 mm)
(10 mm)
Hexagonal bar
(Part Number 895412-20960)
ADJUSTING CARBURETOR
(As Required)
GENERAL INFORMATION
The idle speed adjuster screw controls the throttle
opening at the idle position.
IDLE ADJUSTMENT
1. Start engine and allow it to run at high idle until
warm.
Idle speed adjustment screw
2. Turn the idle speed screw clockwise until drill
bit begins to move.
3. Turn idle screw counterclockwise 1 and 1/2 to 2
turn or until the drill bit stops (2700 to 3300
r/min).
High Altitude Operation
This engine has been factory adjusted to maintain
satisfactory starting, emission, and durability
performance up to 1100 feet above sea level (ASL)
(96.0 kPa). To maintain proper engine operation
and emission compliance above 1100 feet ASL the
carburetor may need to be adjusted by an
authorized ECHO service dealer.
NOTE
When there is some trouble with the carburetor,
contact your dealer.
IMPORTANT
If the engine is adjusted for operation above
1100 feet ASL, the carburetor must be
readjusted when operating the engine below
1100 feet ASL, otherwise severe engine damage
may result.
14
CLEANING CYLINDER FINS
(Check Periodically)
NOTE
Clogged fins will cause poor engine cooling.
1. Carefully remove housing and clean dirt and
dust from fins.
2. Reinstall housing.
CLEANING SILENCER AND
EXHAUST PORT
(Check Periodically)
1. Carefully remove housing halves.
2. Remove and disassemble silencer.
NOTE
Be careful not to scratch the cylinder or piston
when cleaning the cylinder exhaust port.
3. Clean deposits from cylinder exhaust port and
silencer.
STORAGE
6. Drain the fuel tank completely and pull the
recoil starter handle several times to remove
fuel from the carburetor.
LONG TERM STORAGE
(Over 30 Days)
7. Remove the spark plug and pour 1/2
tablespoon (1/4 oz) of fresh, clean, 2-stroke
engine oil into the cylinder through the spark
plug hole.
Do not store your unit for a prolonged period of
time (30 days or longer) without performing
protective storage maintenance which includes the
following:
A. Place a clean cloth over the spark plug hole.
1. Store unit in a dry, dust free place, out of the
reach of children and other unauthorized
persons.
B. Pull the recoil starter handle 2 or 3 times to
distribute the oil inside the engine.
C. Observe the piston location through the
spark plug hole. Pull the recoil starter handle
slowly until the piston reaches the top of its
travel and leave it there.
2. Place ignition switch in STOP position.
3. Remove accumulation of grease, oil, dirt and
debris from exterior of unit.
4. Perform all periodic lubrication and services
that are required.
8. Install the spark plug (do not connect ignition
cable).
5. Tighten all the screws, bolts and nuts.
9. Lubricate the drill bit with a heavy coat of oil to
prevent rust.
NOTE
WARNING
DO NOT STORE IN AN ENCLOSURE WHERE
FUEL FUMES MAY ACCUMULATE OR
REACH AN OPEN FLAME OR SPARK.
For future reference, you should keep this
operator’s manual.
15
SPECIFICATIONS
EDR-210
Mass
without drill bit
Volume
fuel tank
Drill
size
chuck capacity
speed
Mission
reduction ratio
lubrication
External Dimensions
length × width × height
without drill bit
Engine
type
engine displacement
recommended maximum engine speed
recommended engine idling speed
engine speed at beginning of clutch engagement
carburetor
ignition
spark plug
starter
clutch
Fuel
mixture ratio
kg
4.6 (10.1 lb)
L
0.5 (16.9 US fl. oz.)
mm
mm
r/min
32 - 178 (1.25 - 7 inch)
13 (0.5 inch)
520
17.1 (regular side)
18.6 (reverse side)
grease
mm
mL(cm³)
r/min
r/min
r/min
gasoline
fuel consumption at engine maximum power
L/h
16
430 × 320 × 265
(16.9 × 12.6 × 10.4 inch)
Air cooled Two stroke single cylinder
21.2 (1.29 cu. inch)
9000
2900
4000
diaphragm type
flywheel magneto - CDI system
NGK BPM8Y
recoil starter
automatic centrifugal
50:1 ratio with ECHO Power Blend X™ ,
ISO-L-EGD (ISO/CD 13738) and JASO
M345-FC/FD two-stroke, air-cooled engine
oil.
Use 89 octane unleaded. Do not use fuel
containing methyl alcohol, more than 10%
ethyl alcohol or 15% MTBE. Do not use
alternative fuels such as E-20 or E-85.
0.47 (15.9 US fl. oz.)
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMRUE\¿OOLQJRXWWKHZDUUDQW\UHJLVWUDWLRQFDUGVXSSOLHGZLWK\RXUXQLW5HJLVWHULQJ\RXUSURGXFWFRQ¿UPV\RXUZDUUDQW\FRYHUDJHDQGSURYLGHVDGLUHFW
OLQNLIZH¿QGLWQHFHVVDU\WRFRQWDFW\RX
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
RSHUDWRU¶VPDQXDO6KRXOGDSURGXFWGLI¿FXOW\RFFXU\RXPXVWDW\RXUH[SHQVHGHOLYHURUVKLS\RXU(&+2XQLWWRDQDXWKRUL]HG(&+2VHUYLFLQJ
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
‡ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for ¿YH \HDUV from
date of purchase.
EXCEPTIONS:
‡ )RUWZRVWURNHHQJLQHSRZHUHGSURGXFWVWKHHOHFWURQLFLJQLWLRQPRGXOHÀH[LEOHGULYHFDEOHV650VROLGGULYHVKDIWVDQG7&WLQHV
are warranted for the OLIH of the product on parts only.
‡ &XWWLQJDWWDFKPHQWVVXFKDVEXWQRWOLPLWHGWREDUVFKDLQVVSURFNHWVEODGHVDQGQ\ORQWULPPHUKHDGVIRUUHVLGHQWLDORUQRQLQFRPH
producing use will be covered for failures due to defects in material or workmanship for a period of GD\V from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
‡ (&+2¶V5DSLG/RDGHU6WULQJ+HDGFDUULHVDOLIHWLPHZDUUDQW\RQWKHOLQHORFNLQJV\VWHPSDUWVRQO\QRODERU5HIHUWR\RXURSHUDWRU¶V
manual for string head installation and maintenance instructions.
‡ $OO 6%6HULHV DQG 352$77$&+0(17 6(5,(6 6SOLW 6KDIW DWWDFKPHQWV FDUU\ WKH VDPH ZDUUDQW\ GXUDWLRQ DV WKH XQLWV WKH\ DUH
GHVLJQHGWR¿W
COMMERCIAL APPLICATION
‡ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one \HDU from the date of purchase.
‡ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two \HDUV from the date of purchase.
EXCEPTIONS:
‡ )RUWZRVWURNHHQJLQHSRZHUHGSURGXFWVWKHHOHFWURQLFLJQLWLRQPRGXOHÀH[LEOHGULYHFDEOHV650VROLGGULYHVKDIWVDQG7&WLQHV
are warranted for the OLIH of the product on parts only.
‡ &XWWLQJDWWDFKPHQWVVXFKDVEXWQRWOLPLWHGWREDUVFKDLQVVSURFNHWVEODGHVDQGQ\ORQWULPPHUKHDGVIRUFRPPHUFLDOLQVWLWXWLRQDO
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of GD\V from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
‡ (&+2¶V5DSLG/RDGHU6WULQJ+HDGFDUULHVDOLIHWLPHZDUUDQW\RQWKHOLQHORFNLQJV\VWHPSDUWVRQO\QRODERU5HIHUWR\RXURSHUDWRU¶V
manual for string head installation and maintenance instructions.
‡ $OO 6%6HULHV DQG 352$77$&+0(17 6(5,(6 6SOLW 6KDIW DWWDFKPHQWV FDUU\ WKH VDPH ZDUUDQW\ GXUDWLRQ DV WKH XQLWV WKH\ DUH
GHVLJQHGWR¿W
RENTAL APPLICATION - 90 DAYS WARRANTY
‡8QLWVIRUUHQWDOXVHZLOOEHFRYHUHGDJDLQVWGHIHFWVLQPDWHULDODQGZRUNPDQVKLSIRUDSHULRGRIGD\VIURPWKHGDWHRISXUFKDVH
(&+2¶VOLDELOLW\XQGHUWKH³/LIHWLPH´FRYHUDJHLVOLPLWHGWRIXUQLVKLQJSDUWVVSHFL¿HGXQGHUWKH352'8&7:$55$17<3(5,2' section of
this warranty statement for ³/LIH´IUHHRIFKDUJHIRUDSHULRGRIWHQ\HDUVDIWHUWKHGDWHRIWKHFRPSOHWHXQLW¶V¿QDOSURGXFWLRQ
17
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
‡GD\UHVLGHQWLDORUQRQLQFRPHSURGXFLQJZDUUDQW\
‡GD\FRPPHUFLDOLQVWLWXWLRQDODJULFXOWXUDOLQGXVWULDOLQFRPHSURGXFLQJRUUHQWDODSSOLFDWLRQZDUUDQW\
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. (&+23RZHU%OHQGŒ7ZR6WURNH2LO LVDSUHPLXPWZRVWURNHRLOVSHFL¿FDOO\IRUPXODWHGWRPHHW,62
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
‡
/DFNRIOXEULFDWLRQRUHQJLQHIDLOXUHGXHWRWKHXVHRIWZRVWURNHRLOVthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. (&+2 3RZHU %OHQGŒ7ZR6WURNH 2LO meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
‡
'DPDJHFDXVHGE\XVHRIJDVRKROFRQWDLQLQJPHWKDQROZRRGDOFRKRORUJDVROLQHFRQWDLQLQJOHVVWKDQRFWDQH. Only use gasoline which
contains RFWDQHRUKLJKHU. Gasohol which contains a PD[LPXPHWKDQROJUDLQDOFRKRORU07%(PHWK\OWHUWLDU\EXW\OHWKHU
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
‡
(QJLQHGDPDJHFDXVHGE\XVHRIHWKHURUDQ\VWDUWLQJÀXLGV
‡
'DPDJHFDXVHGE\WDPSHULQJZLWKHQJLQHVSHHGJRYHUQRURUHPLVVLRQFRPSRQHQWVRUUXQQLQJHQJLQHVDERYHVSHFL¿HGDQGUHFRPPHQGHG
engine speeds as listed in your operator’s manual.
‡
2SHUDWLRQRIWKHXQLWZLWKLPSURSHUO\PDLQWDLQHGUHPRYHGFXWWLQJVKLHOGRUUHPRYHGGDPDJHGDLU¿OWHU
‡
'DPDJHFDXVHGE\GLUWSUHVVXUHRUVWHDPFOHDQLQJWKHXQLWVDOWZDWHUFRUURVLRQUXVWYDUQLVKDEUDVLYHVDQGPRLVWXUH
‡
'HIHFWVPDOIXQFWLRQVRUIDLOXUHVUHVXOWLQJIURPDEXVHPLVXVHQHJOHFWPRGL¿FDWLRQVDOWHUDWLRQVQRUPDOZHDULPSURSHUVHUYLFLQJRUXVH
of unauthorized attachments.
‡
,QFRUUHFWVWRUDJHSURFHGXUHVVWDOHIXHOLQFOXGLQJIDLOXUHWRSURYLGHRUSHUIRUPUHTXLUHGPDLQWHQDQFHVHUYLFHVDVSUHVFULEHGLQWKHRSHUDWRU
V
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
‡
)DLOXUHVGXHWRLPSURSHUVHWXSSUHGHOLYHU\VHUYLFHRUUHSDLUVHUYLFHE\DQ\RQHRWKHUWKDQDXWKRUL]HG(&+2VHUYLFLQJGHDOHUGXULQJWKH
warranty period.
‡
&HUWDLQparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
‡
8VH RI VSDUN SOXJV RWKHU WKDQ WKRVH PHHWLQJ SHUIRUPDQFH DQG GXUDELOLW\ UHTXLUHPHQWV RI WKH 2(0 VSDUN SOXJ OLVWHG LQ WKH 2SHUDWRU
V
Manuals.
‡
2YHUKHDWLQJRUFDUERQVFRULQJIDLOXUHVGXHWRUHVWULFWHGFORJJHGH[KDXVWSRUWRUFRPEXVWLRQFKDPEHULQFOXGLQJGDPDJHWRVSDUNDUUHVWHU
screen.
‡
$GMXVWPHQWVDIWHUWKH¿UVWWKLUW\GD\VDQGEH\RQGVXFKDVFDUEXUHWRUDGMXVWPHQWDQGWKURWWOHFDEOHDGMXVWPHQW
‡
'DPDJHWRJHDUVRUJHDUFDVHVFDXVHGE\FRQWDPLQDWHGJUHDVHRURLOXVHRILQFRUUHFWW\SHRUYLVFRVLW\RIOXEULFDQWVDQGRUIDLOXUHWRFRPSO\
with recommended grease or oil change intervals.
‡
'DPDJHFDXVHGE\ORDGLQJ6+5('
1
9$&® beyond recommended capacity.
‡
'DPDJHFDXVHGE\SXPSRUVSUD\HUUXQQLQJGU\SXPSLQJRUVSUD\LQJFDXVWLFRUÀDPPDEOHPDWHULDOVRUODFNRIRUEURNHQVWUDLQHUV
‡
$GGLWLRQDOGDPDJHWRSDUWVRUFRPSRQHQWVGXHWRFRQWLQXHGXVHDIWHURSHUDWLRQDOSUREOHPRUIDLOXUHRFFXUV6KRXOGRSHUDWLRQDOSUREOHPRU
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COM<RXUUHFHLSWRISXUFKDVHLQFOXGLQJGDWHPRGHODQGVHULDOQXPEHUPXVWEHPDLQWDLQHGDQGSUHVHQWHGWRDQDXWKRUL]HG
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
FRQVHTXHQWLDOGDPDJHVVR\RXPD\DOVRKDYHRWKHUVSHFL¿FOHJDOULJKWVZKLFKYDU\IURPVWDWHWRVWDWH7KLVOLPLWHGZDUUDQW\LVJLYHQE\(&+2
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
7KLVOLPLWHGZDUUDQW\LVLQOLHXRIDOORWKHUH[SUHVVHGRULPSOLHGZDUUDQWLHVLQFOXGLQJDQ\ZDUUDQW\RI),71(66)25$3$57,&8/$5385326(
OR USE and any implied warranty of MERCHANTABILITYRWKHUZLVHDSSOLFDEOHWRWKLVSURGXFW(&+2DQGLWVDI¿OLDWHGFRPSDQLHVVKDOOQRWEH
OLDEOHIRUDQ\VSHFLDOLQFLGHQWDORUFRQVHTXHQWLDOGDPDJHLQFOXGLQJORVWSUR¿WV7KHUHDUHQRZDUUDQWLHVH[WHQGHGRWKHUWKDQDVSURYLGHGKHUHLQ
7KLVOLPLWHGZDUUDQW\PD\EHPRGL¿HGRQO\E\(&+2
99922201032
11/18/2011
18
E01305001001/E01305999999