Eclipse - Fujitsu Ten AVN8826 GPS Receiver User Manual

English
HDD Navigation System with 7 "Wide TFT Display and DVD/MS Multi-Source Receiver
English
MODEL
INSTALLATION MANUAL
English
Be sure to read this installation manual thoroughly before carrying out installation and making connections. If
installation methods or non-standard parts that are not specified in this installation manual are used, accidents or
injury may result.
Professional installation is recommended, contact the place of purchase to schedule an appointment. After reading
the owner's manual and the installation manual thoroughly, keep them in a safe place for later reference.
To dealers:
Give this installation manual to the customer after installation and connections have been completed.
English
Contents
Connections
2
For your safety in using the AVN8826
3
Names and functions of terminals
4
Connecting the vehicle speed pulse, parking brake, and reverse cables (wires)
6
System connection example
8
Installing the GPS antenna
Installing the main unit
9
11
English
Installation
Components
English
Before
installation
English
English
Components
Check that all of the following components are present
Main unit components
English
1 Main unit
2 Interconnecting cable
3 Interconnecting cable
(Power and speaker connector)
(16P) x 1
x1
5 Antenna cable
6 Bezel
English
x1
(E-lan etc)
(16P) x 1
7 Mounting sleeve
x1
9 Case
4 Interconnecting cable
(Speed pulse, parking,
reverse,video, etc)
(20P) x 1
10 Splicing connector
(For detachable panel) x 1
8 Side bracket
x1
12 Thin flat screw
11 Flat head screw
x3
x2
(M4x5) x 4
(M4x6) x 4
English
13 Pan screw with washer
(Blue:M4x3) x 4
GPS antenna components
English
14 GPS antenna
x1
17 Body protective sheet
16 Earth plate
15 Waterproof cushion
x1
x1
x1
Wiring components
English
18 Clamp
(for GPS antenna) x 3
19 Cable tie
20 Harness affixing tape
x4
x3
Tip
English
When installing the main unit, some vehicle models may require the use of items that need to be obtained
separately such as a power supply adaptor cable, radio antenna adaptor cable or mounting bracket.
-2-
Warnings and caution signs, illustrated bellow, are posted throughout this manual as well as on the AVN8826. They
show safe and correct ways to handle the product so as to prevent personal injury to you and others and avoid damage
to property.
Before reading through the manual, take time to read through and learn the important information listed in this section.
This sign indicates a situation in which incorrect handling through disregard of a sign
might result in death or serious personal injury.
Tip
This section contains information that can help to prevent problems and damage to
the unit, and also contain other useful information.
• When making holes (example: drilling), be sure to wear
protective eyewear. Otherwise, an injury such as loss of
eyesight may result.
• Do not install this product in locations where it may interfere
with the operation of the steering wheel, shift lever, brake
pedal, etc. Otherwise, an accident or injury may result.
• Exposed wires must be insulated with electrical tape.
Otherwise, a short circuit, fire, or electric shock may result.
• Do not modify this system for use other than that specified
herein. Also, do not deviate from the installation procedures
described herein; Fujitsu ten will not be held liable for
damages including, but not limited to serious injury, death,
or property damage resulting from installations that enable
unintended operation.
• When installing this product, never use the existing nuts or
bolts that secure parts of the fuel tank, or the steering, or
braking systems. Otherwise, improper steering, or braking
or a fire may result.
• This unit is intended for operation in 12volt DC, negativegrounded vehicles only. Never use it in 24-volt vehicles
such as heavy trucks or diesel vehicle with cold-region
specifications.
• To prevent a short circuit from occurring, disconnect the
battery's negative terminal before installing this product.
Otherwise, an electric shock or injury may result.
• Do not place the vinyl storage bag over a person's head. It
may cause a serious accident or death by suffocation.
• Do not disassemble or rebuild this product. Doing so may
cause an accident, fire, or electrical shock.
• When using an existing nut and/or bolt from the vehicle to
earth this product, do not use any that secure parts of the
steering or braking systems. Otherwise, an accident may
result.
• When it is necessary to replace the fuse, always use a fuse
of the correct rating (number of amperes). Use of fuses with
higher amperage ratings may cause a fire.
• Do not operate the product in a malfunctioning condition,
for instance, when the audio does not play. Doing so may
result in an accident, fire, or electrical shock.
• If an abnormal situation occurs, such as foreign matter
entering or liquid splashing on the product, or smoke or a
strange odour emitting from the unit, shut off the product
immediately and consult the dealer from whom you
purchased it. Continued operation may cause an accident,
fire, or electrical shock.
• Never supply power to another electrical appliance by
splicing or tapping into this product's power lead (wire).
Otherwise, the current capacity of the wire will be
exceeded, resulting in a fire or electric shock.
• Never attempt to disassemble or modify the product.
Otherwise, an accident, fire, or electric shock may result.
• When routing cables, use precautions to prevent contact of
sharp metal parts such as brackets or screw tips.
Otherwise, a short circuit, electric shock, fire, or accident
may result.
• When installing this product, be sure to use the supplied
mounting hardware. If parts other than those supplied are
used, the unit may be damaged internally, or may not be
held in place securely and become dislodged.
• Play the audio at a moderate volume level that permits you
to hear sounds from outside the vehicle. Driving without
being able to hear outside sounds may result in an
accident.
• Avoid installing this product in places where it may get wet,
such as near windows, or in places that are moist or dusty.
Presence of liquid, moisture, or dust inside this product can
cause short circuiting resulting in smoke or fire.
• This product must be operated only as on-board equipment,
or it may cause electrical shock or injury.
• Do not play distorted sounds for long periods of time; the
speakers may overheat and cause a fire.
• If this product is not connected properly, a short circuit, fire,
or accident may occur.
-3-
English
• For best results, this product should be installed by a
professional installer.
Contact the dealer whom you purchased the product for an
appointment.
English
• When installing the product into a vehicle with a passenger
side air bag, do not secure it to the air bag's cover or in
places where it may impede air bag deployment. Otherwise,
proper air bag operation may not be ensured in the event of
an accident, causing injury or death.
English
• Bundle cables and harnesses with electrical tape or wire
ties to prevent them from interfering with moving parts. If
they should entangle with the steering wheel, shift lever, or
brake pedal, an accident may result.
English
• To prevent damage to the vehicle, confirm the locations of
hoses, electrical wiring, and the fuel tank prior to drilling
holes to install this product. Also, take precautions so that
the product does not interfere, nor come in contact with
them. Otherwise, a fire may result.
English
• Do not install this product in locations where it may obstruct
the driver's view, or where it may endanger passengers in
the vehicle. Otherwise, an accident or injury may result.
English
This sign indicates a situation in which incorrect handling through disregard of a sign
might result in personal injury or may result solely in damage to property.
English
For y our safety in using the AVN8826
English
Names and functions of ter minals
English
• Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity of
the power cable is exceeded, fire and electric shocks may result.
• The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If
they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal,
accidents may result.
• If removing the end of the cord to connect to another cord, be sure to wrap PVC tape or a similar wire insulating
method around the connection to insulate it. If the connection is not insulated, fire or accidents may result.
4 INTERCONNECTING CABLE (E-lan etc)
16P
8
7
English
13P
F
5 ANTENNA CABLE
ANTENNA PLUG
1 MAIN UNIT
20P
4P
E
D
1P
English
C
16P
A
14 GPS ANTENNA
2 INTERCONNECTING
CABLE
(Power and speaker
connector)
3
4
B
5
8
6
English
Tip*1
1
TO VEHICLE-SIDE
CONNECTOR
2
3 INTERCONNECTING CABLE
(Speed pulse, parking, reverse,video, etc)
Tip*1
• The positions of the B+ and ACC pins on the connector may
vary depending on the vehicle. In such cases, replace the end
of the connector. Ask your dealer for details on connector pin
positions.
English
• Installation is not possible for vehicles without ACC.
Tip
English
• Refer to page 5 for details on the wire colours and connection points for interconnecting cables 2 , and 3 and
4
.
-4-
1
2
and
3
and
Antenna power supply (Blue)
Connect to the automatic-antenna control terminal of the vehicle.
2
Control power supply (Blue/White)
4
English
Wire colours and connection points for connection cables
Connect the control terminal for the external amplifier, etc.
Vehicle speed pulse signal wire (Purple/White)
English
3
Connect to the vehicle speed pulse signal terminal.
4
Parking brake signal wire (Red/White)
Connect to the parking brake signal terminal.
5
Reverse signal Wire (Green)
Connect the reverse signal output of the vehicle to this terminal.
Navi mute Wire (Brown)
Connect to the NAVI-MUTE terminal of a DCU105 or similar device (sold separately).
7
Cellular phone mute Wire (Pink)
Connect to the earth output terminal on a mobile phone.
8
H/A mute Wire (Light Green)
English
6
Connect to the DVD-MUTE terminal of a DCU105 or similar device (sold separately).
9
Connect where good body earthing is available.
A
NAVI-VOICE output terminal
Connect to the NAVI-VOICE input terminal of an external device such as a DCU105 (sold
separately).
B
Digital output terminal
C
VTR input terminals
D
VTR output terminals
English
Earth (Black)
Connect to the DIGITAL input terminal of an external device such as a DCU105 (sold separately).
Connect to the monitor with video input.
Yellow : Video signal
White : Audio (left) signal
Back-eye camera external input terminal (4P)
F
E-LAN terminal (13P)
Red : Audio (right) signal
Used with the Eclipse back-eye camera (sold separately).
Connect to the E-LAN terminal of the CD changer, etc.
- Vehicle connections -
English
E
English
Connect the output cable of external video equipment such as a VTR.
Yellow : Video signal
White : Audio (left) signal
Red : Audio (right) signal
Tip
-5-
English
• You will need to purchase the necessary component adapter cable for the vehicle so that the power supplies can
be utilised. (Contact the dealer for further details.)
• Be sure to wrap the connection cables with plastic tape to insulate them.
English
Connecting the vehicle speed pulse , par king
br ak e , and reverse cab les (wires)
Notes on installation
English
• Check the vehicle speed pulse signal, parking brake signal, and reverse signal carefully before making the
connections. If the cables are incorrectly connected, accidents or problems with correct operation may result.
• The label on the vehicle speed pulse signal cable contains a protection circuit, so do not cut the cable or remove
the protective circuit, otherwise problems with operation may result.
• Bind the cables together with tape so that they do not cause an obstruction while driving. If they become wound or
entageled around parts such as the steering wheel, shifting lever, or brake pedal, accidents may result.
Tip
The locations where the vehicle speed pulse signal cable, parking brake signal cable, and reverse cable may vary
depending on the vehicle model and grade. Ask the car dealer or your nearest Eclipse dealer for details.
English
- Connecting point for the vehicle speed pulse signal (example) Vehicle speed pulse
signal cable (vehicle harness)
Tip
Engine computer
Always be sure to connect the vehicle speed pulse,
otherwise the measurement precision will be greatly
reduced.
English
1
Use a splicing connector to connect the vehicle speed
pulse signal cable (purple/white) coming from the main
unit to the vehicle speed pulse signal cable of the
vehicle.
2
Route the vehicle speed pulse signal cable to the main
unit.
Vehicle speed pulse
signal cable
(purple/white) of
connection cable
10 Splicing connector
Contains a protective circuit
so never remove.
English
- Connecting the point for parking brake (example) 1
2
Use a splicing connector to connect the parking brake
signal cable (red/white) coming from the main unit to
the parking brake signal cable of the vehicle.
Hand-operated
parking brake
Parking brake
signal cable
Foot-operated
parking brake
Route the parking brake signal cable to the main unit.
English
Parking brake
signal cable
Attach a splicing
connector at this location
Parking brake
signal cable
English
-6-
Tip
• Be sure to connect the reverse signal cable. If it is not
connected, the vehicle position may be incorrect when
the vehicle is reversed.
• Use a circuit tester to confirm that a sensing voltage of
6 V or higher is generated when the vehicle is reversed.
Use a splicing connector to connect the reverse signal
cable (green) coming from the main unit to the reverse
signal cable of the vehicle.
2
Route the reverse signal cable to the main unit .
English
1
Attach a splicing
connector at this location
Reverse lamp
Reverse signal cable
Reverse signal cable
Vehicle speed pulse signal cable
(purple/white), parking brake cable
(red/white), or reverse cable (green)
Harness in the car
Push in the terminal (the metal part) of the splicing
connector using a pair of pliers.
English
2
Insert the connection cable [vehicle speed pulse signal
cable (purple/white), parking brake signal cable
(red/white), or reverse signal cable (green)] from the
main unit and the vehicle cable into the splicing
connector.
English
- Using the splicing connector 1
English
- Connecting point for the reverse signal (example) -
10 Splicing connector
Press down the cover of the splicing connector and
squeeze it until it locks.
Lock
English
10 Splicing connector
English
3
English
-7-
English
System connection example
English
• Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity of
the power cable is exceeded, fire and electric shocks may result.
• The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If
they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal,
accidents may result.
• If removing the end of the cord to connect to another cord, be sure to wrap PVC tape or a similar wire insulating
method around the connection to insulate it. If the connection is not insulated, fire or accidents may result.
Tip
• Install and connect all of the peripheral units before connecting them to the main unit.
• Do not remove any of the protective caps (RCA, etc.) unless in use.
• Be sure to wrap the connection cables with tape (PVC tape) to insulate them.
Tip*1
English
- Speaker connection examples For a front 3-way speaker system
k
lac
B
To centre speaker
(with amplifier) or
external amplifier
To external
anplifier
TO EARTH
These speaker cables are not used when
connecting an external amplifier.
If not using an external amplifier, connect the
front and rear speakers using these speaker
cables.
L
English
k
Pin
2V
+1 ly)
Y
TE
ER pp
wn
TT t Su
MU
Bro
DBA nen
E
DV
TO rma
T
MU
(Pe
VI
NA
16P
To centre speaker
(with amplifier) or
external amplifier
SW
Hi
Mid
L
To external
anplifier
English
ck
4
To external anplifier
Mid
Mid Low
To sub woofer
(with amplifier) or
external amplifier
MICROPHONE
(supplied with DCU105)
DCU105
(sold separately)
LE
AB
GC
N
I
T
EC
NN
CO
R
E
INT
16P
Pin
k
Lig
ht
Gr
ee
n
13P
English
MAIN UNIT
1P
English
GPS ANTENNA
INTERCONNECTING CABLE
(Power and speaker connector)
4P
T
PU
UT
IO
V
NA
k
c
Bla
e
hit
e/W
u
l
B
TO TURN-ON LEAD OF EACH UNIT (Power Supply)
e
Blu
UT
TP
OU
L
ITA
DIG
TO EARTH
TO POWER ANTENNA RELAY (Supply)
DIGITAL
INPUT
5)
10
CU
E
D
L
B ith
CA d w
DIN pplie
u
(s
BEC105
(sold separately)
ANTENNA
CABLE
20P
16P
12P
13P
(su
pp
lied R
TE
wit CA C
hD A
LM
CU BLE
U
H/A
TE
10
MU
5)
TE
13P
5
NAVI VOICE OUTPUT
VIDEO OUTPUT
13P
ANTENNA
PLUG
2
Hi
• See DCU 105 owners manual for details.
Tip*1
OU
T(
Do
no
t re
mo
)
ve
tc
e
cap
n
a
-l
)
E
(
TO EARTH
14
SW
INTERCONNECTING CABLE
(supplied with DCU105)
POWER CONNECTOR CABLE
(supplied with CH3083)
1
FRONT
R
REAR
DIG
ITA
L
Bla
L
CENTER
R
Mid Low
INTERCONNECTING CABLE
(supplied with DCU105)
CH3083
(sold separately)
2V
+1 )
RY upply
E
TT t S
BA nen
llow
TO rma
e
Ye
P
(
To external anplifier
FRONT
R
REAR
To external
anplifier
To sub woofer
(with amplifier) or
external amplifier
For a front 1-way speaker system
L
CENTER
R
llow
Ye
DIN CABLE
(supplied with CH3083)
To external
anplifier
5)
10
E DCU
L
AB ith
AC dw
RC pplie
u
L
(s
NA
ION )
CT ap
SIG
NE ove c
SE
N
L
U )
CO rem
L
DP e6
NO o not
NA
EE ag
SP r to p
(D
SIG
E
e
E
L ef
AK
HIC (R
BR
VE AL
L
G
le/ TO MIN
N
p
NA
I
r
)
R
K
6
Pu ite
TE
SIG
AR page
h
E
P
W
RS )
TO fer to
d/
VE e 7
Re ite
(Re
RE pag
Wh
TO fer to
n
(Re
ee
TE
Gr
MU
VI
NA
wn
Bro
TO VEHICLE-SIDE CONNECTOR
-8-
3
INTERCONNECTING CABLE
(Speed pulse, parking, reverse,video, etc)
Notes on installation
Tip
• If installing the GPS antenna inside the vehicle, be
sure it is mounted to the earth plate.
• The materials used in front and rear vehicle windows
can cause GPS reception sensitivity to drop
significantly. If this happens, install the GPS antenna
on the outside of the vehicle.
• Wipe the installation surface thoroughly so that it is
clear of any dirt, moisture, or grease before installing
the antenna.
• Route the GPS antenna cable as far away as
possible from TV and radio antennas, and cables,
otherwise, it may cause interference with video and
audio signals.
• Hold the main antenna unit when removing the
antenna. Do not pull on the cable, otherwise it may
become damaged and result in problems with correct
operation.
• If installing the GPS antenna outside the vehicle,
remove the main antenna unit when washing the
vehicle. (If you wash the vehicle with the main
antenna unit still attached, avoid spraying the cable
section directly with water so that no water gets
inside the vehicle.)
• The magnet that is attached to the GPS antenna is
extremely strong. Be sure to note the following when
installing the antenna.
• Do not put the antenna down on the earth or on
dirty or dusty surfaces. If iron filings become
attached to the magnet, they may cause damage
to the vehicle's body.
• Keep the antenna away from watches and
magnetic cards, otherwise they may be damaged
and/or rendered unusable.
English
• Do not apply any coatings to the GPS antenna,
otherwise it may cause a drop in the reception
sensitivity of the antenna.
• If installing the GPS antenna outside the vehicle,
remove the main antenna unit if leaving the vehicle
unattended for long periods in order to prevent theft
or malicious damage to the antenna.
English
• If the attachment surface is a non-plastic surface
such as genuine leather, wood panel, or cloth,
attaching the antenna may damage the surface
finish. Do not attach the earth plate to such surfaces.
• The GPS antenna should be installed in a level
position where the signals will be as unobstructed as
much as possible, such as on the vehicle's roof.
Satellite signals cannot be received if the antenna is
obscured or obstructed.
English
• If installing the GPS antenna inside the vehicle, the
location and the slope of the vehicle's windscreen will
determine the accuracy of the GPS antenna to
receive the GPS signal. If the GPS antenna location
inside the vehicle is hindering the accuracy of the
GPS antenna, then you may want to install the
antenna outside of the vehicle.
• Do not install the antenna in places (such as front
pillars and roof panel) that are shielded from the sky.
English
• If the vehicle glass is a special type of glass such as
heat-reflective glass or bullet-proof glass, be sure to
install the GPS antenna outside of the vehicle. If the
GPS antenna is installed inside of the vehicle, the
reception sensitivity will severely drop and will affect
the accuracy of the position measurement.
English
• The cables should be bound together with tape or a similar securing method (example: wire ties) so that they do
not interfere with driving. If it becomes wound or entangled around parts such as the steering wheel, shifting lever,
or brake pedal, accidents may result.
• Do not install the GPS antenna where it will obstruct the driver's vision or where it will be an obstacle while driving,
otherwise traffic accidents may result.
English
Installing the GPS antenna
English
-9-
- Installation inside the vehicle (example) -
English
1
Choose an installation location on the dashboard which
is flat and has a clear view of the sky.
16 Earth plate
14 GPS antenna
Tip
English
• Select a location that is at least 20 in. away from the
main unit. If this is not done, the GPS measurement
precision will drop.
• Be sure to use the earth plate when installing the GPS
antenna. If the earth plate is not used, the reception
sensitivity will drop and will affect the accuracy of the
position measurement.
2
Install the earth plate to the dashboard.
3
Install the GPS antenna to the earth plate.
Tip
Front of vehicle
Tip
English
If installing the GPS antenna inside the vehicle, the installation location and the shape of the vehicle's body will
determine GPS accuracy. Accuracy is usually lower when the GPS antenna is installed inside the vehicle.
4
Route the GPS antenna cable to the main unit's
installation location.
Tip
Cut the harness affixing tape into usable lengths with scissors. Do the same for the rest of the installation.
English
- Installation outside the vehicle (example) 1
English
Choose an installation location where the GPS antenna
can be attached securely.
14 GPS antenna
2
Remove the backing paper from the body protective
sheet and attach the sheet to the vehicle.
17 Body protective
sheet (clear)
3
Install the GPS antenna on top of the body protective
sheet.
Front of vehicle
English
4
Route the GPS antenna cable inside the vehicle's boot
and secure it with clamps.
5
Attach the waterproof cushion so that the GPS antenna
cable is flat against the weatherstrip when the boot lid
is closed.
15 Waterproof cushion
Tip
To aid in sliding the waterproof cushion in finding the
desired mounting location, apply plain or soapy water
to the waterproof cushion.
English
6
Route the GPS antenna cable to the main unit while
securing it with harness affixing tape.
Front of vehicle
20 Harness affixing tape
Weatherstrip
Tip
Cut the harness affixing tape into usable lengths with scissors. Do the same for the rest of the installation.
- 10 -
English
Installing the main unit
- Installation angle -
Tip
Front
To maintain proper function, the unit must be mounted
less than 30 degrees. If the angle is in excess of 30
degrees, DVD/CD skipping and improper DVD/CD and
Memory Stick ejection may occur.
Level (reference)
- Installation preparation-
Tip
Caution
In the event that the main unit requires shipping, reattach
the caution label to help prevent potential damage that may
be caused by shipping.
Caution label
English
1
Before the main unit installation, be sure to remove the
caution label.
Main unit
1
Tip
• Carefully bind any excess length of cord that is
connected to the main unit and secure it to an area of
empty space in the vehicle so that it does not move
around or get caught in the main unit or vehicle-side
equipment. If the cords are not handled correctly,
operating problems or short-circuits may occur, and this
may result in the danger of fire or other accidents.
• Connect all cables before installing the main unit.
Use a screwdriver or a similar tool to bend the tabs in
the mounting sleeve to secure the mounting sleeve.
3
Attach the side brackets to the main unit using flathead
screws.
7 Mounting sleeve
11 Flat head screws
(M4 x 6) x 2
Main unit
1
Tip
Be sure to use the supplied accessory mounting screws
(M4 x 6) as the mounting screws. If any other screws
are used, they may damage the inside of the unit.
8 Side brackets
example 2
example 1
1
Main unit
1
Main unit
Front of vehicle
Front of vehicle
Screw
position
8 Side brackets
8 Side brackets
By adjusting the positions of the brackets, the main unit's
installed depth can be adjusted.
- 11 -
English
Screw
position
English
2
English
Insert the mounting sleeve into the opening in the
vehicle dashboard or console box.
Bend the mounting
tabs.
Dashboard or
console box
English
- Main unit installation example (If installing the main unit using the mounting sleeve) -
1
English
30˚ or less
English
4
Insert the main unit into the mounting sleeve until it
locks in place.
5
Fasten the rear of the main unit.
6
Install the bezel on the main unit.
Metal of vehicle
Dashboard or console box
Tip
English
• Be careful not to forcefully push on the main unit's
display or buttons during installation. This may result in
damage to the main unit.
• This installation method is only one example. When
installing the main unit to the vehicle, be sure to as the
place of purchase for information on what installation
method to use.
7 Mounting sleeve
6 Bezel
- Main unit installation example (If installing the main unit using the side brackets of the vehicle) -
Tip
Centre cluster panel
English
• Carefully bind any excess length of cord that is
connected to the main unit and secure it to an area of
empty space in the vehicle so that it does not move
around or get caught in the main unit or vehicle-side
equipment. If the cords are not handled correctly,
operating problems or short-circuits may occur, and this
may result in the danger of fire or other accidents.
• Connect all cables before installing the main unit.
English
1
Remove the pocket and any other accessories from the
centre cluster to make room for the main unit.
2
Remove the mounting brackets for the pocket.
3
Attach the brackets to the main unit.
Pocket, etc
Mounting bolts
If using these installation holes, be sure to use
the 13 Pan screw with washer (Blue:M4 x 3).
Tip
12 Thin flat screws
(M4 x 5) x 4
Be sure to use the supplied accessory mounting screws
(M4 x 5) as the mounting screws. If any other screws
are used, they may damage the inside of the unit.
1
English
4
Main unit
Screws x 2
Install the main unit in the vehicle.
Pocket
Mounting bracket
Tip
English
• Be careful not to forcefully push on the main unit's
display or buttons during installation. This may result in
damage to the main unit.
• This installation method is only one example. When
installing the main unit to the vehicle, be sure to as the
place of purchase for information on what installation
method to use.
example 1
1
example 2
Main unit
Front of vehicle
Screw position
1
Main unit
Front of vehicle
Screw position
By adjusting the positions of the brackets, the main unit's
installed depth can be adjusted.
English
- 12 -