Edelbrock 16211-MBN-640 Automobile Parts User Manual

Edelbrock 16211-MBN-640 Automobile Parts User Manual
INSTRUCTION SUPPLEMENT FOR 2000LATER HONDA XR650R
SPECIAL NOTE!!!!!!
The Edelbrock carb you have
purchased was designed to be used
with the Honda Power-Up manifold.
Honda part #16211-MBN-640.
Removing stock carburetor and cables.
1. Remove seat and gas tank. Make sure fuel
petcock is in “off” position.
2. Remove throttle cables paying close
attention to routing, as the new cables will
need too be routed the same.
3. Remove stock carburetor and stock throttle
housing.
4. Stuff a dry, clean rag into the intake
manifold to keep debris from entering
engine.
9. Remove rag from manifold.
10. Install carburetor into manifold. Do not
tighten yet.
11. Install the pull cable (long shoulder on cable)
into the 4:00 position and the return cable
end into the 1:00 position of the cable
wheel. Secure cables to cable bracket by
replacing end piece and phillips screw. See
figure 2.
Figure 2.
NOTE: It may be easier to remove sub-frame
prior to installation.
Installing the Edelbrock Carburetor and
Throttle Cables
5. Install the throttle cables into the supplied
throttle housing and place onto clean
handlebar end.
6. Remove the rubber carburetor alignment
tabs from the manifold using a razor blade or
sharp cutters. This should be done with the
rag left in the manifold. Be very careful not
to damage the manifold or your hands
while doing this!!
7. Remove the hex pipe plug from the carb cap
using a 11mm or 7/16 wrench. Do not
discard plug, as it will be needed later.
Install the metering adjustment tool included
in the hardware kit. Do not over-tighten as
damage may occur to cap.
8. Install stock fuel line onto fuel banjo with the
elbow pointed up and secure with clamp.
See figure 1.
Figure 1.
12. Align carburetor as close to vertical as
possible and tighten manifold clamp.
13. Adjust cable until wide-open throttle is
achieved. Adjust return cable to take up the
slack. Note: When throttle cables are
properly adjusted, there should be
approx. 1/8” of free play in the throttle.
14. After throttle cables have been adjusted the
handle bars should be rotated from full right
stop to full left stop while opening and
closing throttle to ensure smooth operation.
Also check to make sure the cables do not
catch or bind on anything, i.e., hand guards,
stabilizers.
15. Secure clamp around air boot onto back of
carburetor.
16. Install Remote Idle Cable into threaded tab
on top of carburetor. Refer to main
instruction manual for remote idle cable
installation and adjustment.
17. Install fuel tank and connect fuel line to
petcock and secure with provided pinch
clamp. Refer to figure 1. Do not bolt tank in
place, as minor adjustments may be
necessary.
18. Turn fuel petcock to “on” and check for
leaks.
19. Open throttle 3-5 times to prime accelerator
pump. Do not open throttle any more than
5 times as this may flood engine!!
20. Once pump is primed, get motor to TDC and
kick through without opening throttle. If
Motor will not fire with a few kicks, open idle
cable ½ turn and repeat starting process.
NOTE: If flooding occurs, slowly open
throttle to wide open and hold. With
throttle still open, hold decompression
lever and kick motor through 5-10 times.
Release throttle and decompression lever
and proceed with normal starting
procedure.
For any questions regarding tuning or
installation of Edelbrock products, please
call our toll free tech line M-F 8:00am-12:
30pm, 1:30pm-5:00pm PST.
877-888-7504 ext.2.
Edelbrock #3115 XR650R
Carburetor Specifications
Bore Size: 36mm Tall X 42mm Wide
Needle: 19E @ 18 Clicks
Accelerator Pump Bypass: 1.5 turns out
Alternate Needles: 17E, 21E
Replacement Cables: #9345
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement