Owner`s manual | Edirol LVS-400 Musical Instrument User Manual

LVS-400_e1.book 1 ページ 2004年1月20日 火曜日 午後12時50分
Owner’s Manual
Thank you, and congratulations on your choice of the EDIROL VIDEO MIX/LIVE SWITCHER
LVS-400.
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (p. 2–3; p. 4). These sections provide important information concerning
the proper operation of the unit. Additionally, in order to feel assured that you have gained a
good grasp of every feature provided by your new unit, Owner’s Manual should be read in its
entirety. The manual should be saved and kept on hand as a convenient reference.
202
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
LVS-400_e1.book 2 ページ 2004年1月20日 火曜日 午後12時50分
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
to damage or
caused with
and all its
to domestic
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
001
008e
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
• Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
..........................................................................................................
..........................................................................................................
002c
• Do not open (or modify in any way) the unit or its
AC adaptor.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
008c
• Be sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified on
the AC adaptor’s body. Other AC adaptors may
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
2
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
101b
• The unit and the AC adaptor should be located so
their location or position does not interfere with
their proper ventilation.
..........................................................................................................
102c
• Always grasp only the plug on the AC adaptor
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103b
• At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug and
the power outlet can result in poor insulation and
lead to fire.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107c
• Never handle the AC adaptor or its plugs with
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
108b
• Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..........................................................................................................
109b
• Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet (p. 8).
..........................................................................................................
110b
• Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
..........................................................................................................
118
• Should you remove the BNC-RCA adaptors, make
sure to put them in a safe place out of children's
reach, so there is no chance of them being
swallowed accidentally.
3
LVS-400_e1.book 4 ページ 2004年1月20日 火曜日 午後12時50分
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following:
Power Supply
Additional Precautions
301
Add
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a
power supply noise filter between this unit and the
electrical outlet.
• This product is compatible with regular NTSC or PAL
video signal. In case irregular signal is input, it may
obstruct stabile operation of this product.
302
• The AC adaptor will begin to generate heat after long
hours of consecutive use. This is normal, and is not a
cause for concern.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Placement
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
4
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
Copyright
851
• Unauthorized recording, distribution, sale, lending, public
performance, broadcasting, or the like, in whole or in part,
of a work (musical composition, video, broadcast, public
performance, or the like) whose copyright is held by a
third party is prohibited by law.
853
• Do not use this unit for purposes that could infringe on a
copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of
third-party copyrights arising through your use of this
unit.
Add
• Even when intended for the user's private enjoyment
(use), any duplication of third-party copyrighted works
that circumvents technology to protect such works
without the permission of the copyright holder is an
infringement of copyright, and is prohibited by law.
Add
• Duplication of works not protected by such technology
are allowed for private individual use.
LVS-400_e1.book 5 ページ 2004年1月20日 火曜日 午後12時50分
Contents
USING THE UNIT SAFELY......................................................................2
IMPORTANT NOTES ...............................................................................4
Before You Begin....................................................................................6
Check the Included Items.......................................................................................................................... 6
Connecting Peripheral Devices ................................................................................................................ 7
Turning the Power On ............................................................................................................................... 8
Turning the Power Off ................................................................................................................... 8
Switching Between NTSC and PAL......................................................................................................... 8
Names of Things and What They Do.....................................................9
Front Panel................................................................................................................................................... 9
Rear Panel .................................................................................................................................................... 9
Basic Operation ....................................................................................10
Switching Images with the Switcher ..................................................................................................... 10
Controlling the Output ............................................................................................................................ 11
Using the Monitor Output to Check the Images.................................................................................. 11
Advanced Operation.............................................................................12
Inserting Images with the Video Fader ................................................................................................. 12
About Insert Effects ...................................................................................................................... 12
Key Composite Effects.................................................................................................................. 13
Control the LVS-400 from an External Device....................................14
Correspondence Between Commands and MIDI Messages.............................................................. 14
Using V-LINK to Control the LVS-400.................................................................................................. 15
Using V-LINK................................................................................................................................ 15
MIDI Implementation Chart ..................................................................16
Troubleshooting....................................................................................17
Specifications........................................................................................18
5
Before You Begin
Check the Included Items
fig.01.e
About Ground Terminal
In some cases, depending on the environment in which the unit is installed, the surface of the panel may sometimes feel
rough and grainy. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are
concerned about this, connect ground terminal (see figure) with an external ground. When the unit is grounded, a slight
noise may result, depending on the particulars of your installation. If you are unsure of the connection method, contact
nearest Edirol Service Center, or authorized Edirol/Roland distributor, as listed on the "Information" page.
fig.02.e
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
6
LVS-400_e1.book 7 ページ 2004年1月20日 火曜日 午後12時50分
Before You Begin
Connecting Peripheral Devices
1
2
3
You can connect up to four video playback devices (sources). Here’s how to connect sources such as a video
camcorder, VCR, DVD player, and play them back to create an impressive video performance. To prevent
malfunction and/or damage to other devices, always turn down the volume, and turn off the power on all
devices before making any connections.
Connect the AC adaptor included with the LVS-400 to the DC IN jack, then plug the adaptor into a power outlet.
Connect the LVS-400 to peripheral equipment as shown in the figure.
fig.03.e
Output Devices
Monitoring Display
(Projector or other display)
Input Devices
(Cameras, VCRs, DVDs, etc.)
AC adaptor
* To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue
stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration.
• The LVS-400 does not have audio inputs so will not mix audio. Audio outputs can be connected directly to speakers or
via an audio mixer if mixing of audio from multiple devices is necessary.
• No video cables come with this product. Please use appropriate video cables for connection with source devices or TV
monitor/Projector.
• It is recommended to use composite cable rather than S-video cable where you need to connect devices long distances
(unless using S-video amplifiers). If devices are installed closer to the LVS-400, it is recommended to use S-video cables
so that you can obtain better image quality.
• If both video (composite) and S-video signals are input simultaneously to the same channel, the S-video signal will take
priority.
• The same image is output simultaneously from the OUTPUT 1, OUTPUT 2, and S-VIDEO outputs.
• The LVS-400 inputs and outputs composite video via BNC connectors. Using the BNC connectors securely locks the
connection. If connecting with RCA phono connectors, use the BNC-RCA phono adaptor included with the LVS-400 or
another commercially available BNC-RCA adaptor to connect to the LVS-400’s BNC connector.
7
Before You Begin
Turning the Power On
1
Check the power cable.
Make sure that the cable from the AC adaptor is firmly plugged into the LVS-400.
2
Press the POWER button.
Press the POWER button located on the rear panel of the LVS-400. It will take approximately five seconds for the LVS400 to initialize itself and begin operating.
fig.04.e
942
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate
normally.
Turning the Power Off
1
Press the POWER button.
Press the POWER button located on the rear panel of the LVS-400. All of the front panel LEDs will go dark.
Switching Between NTSC and PAL
The LVS-400 can be switched to support either NTSC or PAL format signals.
To start up in PAL mode, hold down monitor select “OUTPUT” button and “OUTPUT ON/OFF” button, and press the
power button.
The next time you start up, you can simply press the power button to start up in PAL mode.
If you want to return to NTSC mode, once again hold down monitor select “OUTPUT” button and “OUTPUT ON/OFF”
button, and press the power button.
When the LVS-400 starts up, an indication of whether it is starting up in NTSC mode or PAL mode will appear for several
seconds in the monitor out screen.
8
Names of Things and What They Do
Front Panel
fig.05.e
Rear Panel
fig.06.e
9
LVS-400_e1.book 10 ページ 2004年1月20日 火曜日 午後12時50分
Basic Operation
Switching Images with the Switcher
You can easily get a transition effect when switching images, just by using the MAIN
[1]–[4] buttons.
1. Play back the images with the video equipment.
Input the images from the video device connected to the LVS-400 (such as a video
camera or DVD player).
2. Check the output.
Turn on the video monitor or projector connected to the LVS-400’s output jacks/
connector and check to see whether or not the images are being output correctly.
3. Switch the input channel.
Switch the LVS-400’s input channel. Turn the TRANSITION TIME control knob so
that it points straight up (2 seconds), then press one of the buttons from [1] through
[4] to switch the input.
Check the image on the video monitor or from the projector to confirm that the
images are switched correctly.
Changing the TRANSITION TIME control knob setting allows you to adjust the
amount of time required to completely switch from one image to another.
fig.07
4. Switch the transition effect.
Press the TRANSITION TYPE select buttons and switch the input.
The following effects are available when switching images.
fig.08.e
MIX: The two images are mixed (overlapped) as they are switched.
Start
Finish
WIPE 1: The images are switched by wiping left to right.
Start
Finish
WIPE 2: The images are switched with a rectangular wipe starting
from the center of the image.
Start
10
Finish
LVS-400_e1.book 11 ページ 2004年1月20日 火曜日 午後12時50分
Basic Operation
Controlling the Output
You can use the OUTPUT (Output Control) button to pause output of the image.
1. Press the Output Control button.
When you press the Output Control button, output of the images is paused.
A black (blank) screen is output, and the button indicator flashes.
A synchronization signal is
output continuously, so the
images remain stable.
2. Press the Output Control button once more.
When you press the button again, the images are output as before.
The button’s indicator goes out.
fig.09
Take care not to mistake the
“OUTPUT” in the MONITOR
selection section for this
button.
Using the Monitor Output to Check the Images
You can check both the input and output without affecting the output images.
1. Play back the images with the video equipment.
Input the images from the video device connected to the LVS-400 (such as a video
camera or DVD player).
2. Check the output.
Turn on the video monitor connected to the LVS-400’s MONITOR OUT connector
and check to see whether or not the images are being output correctly.
3. Switch the view using the Monitor Select buttons.
Switch using the Monitor Select buttons. You can select from Inputs 1 through 4 or
the OUTPUT. The selected image is displayed on the video monitor.
fig.10
When selecting the MONITOR
OUTPUT, the video OUTPUT
in the monitor is disrupted for
a moment, but this has no
effect on the actual video being
OUTPUT.
Check the following if there is no video output.
• Is the output of the video device properly connected to the LVS-400’s input?
• Is video being output from the video device connected to the LVS-400’s input?
• Is the input for the output projector or video monitor properly selected?
• Is the Output Control button indicator unlit? Press the button if the indicator is
flashing.
A blue screen is displayed when you select a channel that has no input connected to
it.
The video fader is used for inserts. For more on inserting, refer to p. 12.
11
LVS-400_e1.book 12 ページ 2004年1月20日 火曜日 午後12時50分
Advanced Operation
Inserting Images with the Video Fader
You can use the video fader to insert video images manually.
When using this feature, you can use the “PinP” (Picture in Picture) or key composite
effects.
fig.11
1
2
3
Pull the video fader all the way toward MAIN.
If you do not start out with the
video fader completely tilted
to the MAIN side, then the
Insert function will not work,
even when you then move the
video fader. First bring the
fader all the way to MAIN to
start the function.
Select the input to insert (1–4).
Move the video fader to the INSERT side.
The video images are inserted as you move the fader.
4
Return the fader to the MAIN side to return to the original image.
About Insert Effects
fig.12
MODE: OFF
When this is set to “OFF,” composite effects are not
applied. The video is inserted in the entire screen
according to the transition selected with the
TRANSITION TYPE selection buttons (p. 10).
MODE: PinP
When PinP is selected, the Picture in Picture function
goes into effect. A small picture is mixed (faded in),
regardless of the TRANSITION TYPE button setting.
fig.13
The position of the smaller picture changes according to the MODE setting (upper
right, upper left, lower right, or lower left).
fig.14.e
MAIN Image
12
INSERT Image
OUTPUT Image
The insert method varies with
the insert effect.
Switch the insert input before
inserting. Although it is
possible to switch the insert
input while the insert is in
progress, note that this
disrupts synchronization.
LVS-400_e1.book 13 ページ 2004年1月20日 火曜日 午後12時50分
Advanced Operation
Key Composite Effects
fig.15
MODE: WHT/BLK/CHR
The key composite functions are enabled when WHT/BLK/CHR is selected.
The video is inserted according to the transition selected with the TRANSITION
TYPE selection buttons.
Adjust the composite effects with the KEY LEVEL adjustment knob.
WHT: Light portions of the inserted image are replaced with the main image.
(White Luminance Key)
BLK: Dark portions of the inserted image are replaced with the main image.
(Black Luminance Key)
CHR: Blue portions of the inserted image are replaced with the main image.
(Blue Chroma Key)
Key Composite Example: MODE: CHR
fig.16.e
MAIN Image
1
2
3
4
INSERT Image
OUTPUT Image
Tilt the video fader to the MAIN side.
Input the video to be used as the background in the final composite output to
MAIN.
Record the video you want to insert against a blue background, then input to
INSERT.
Return the fader to the INSERT side.
The composite output video appears as shown in the figure above.
You can adjust with the KEY LEVEL knob.
5
Return the fader to the MAIN side to return to the original image.
If you reselect the MAIN input
while the Insert function is still
in use, the insert is
automatically cleared, and the
video image switches via the
transition effect from the
current MAIN image to the
newly selected image. If you
want to use the Insert function
again, first bring the fader all
the way to the MAIN side,
then move it to INSERT again.
13
Control the LVS-400 from an External
Device
You can connect the LVS-400 with a MIDI device, and control the LVS-400 remotely.
What is MIDI?
MIDI stands for “Musical Instrument Digital Interface” a worldwide standard that allows performance data and other
information to be exchanged among musical instruments. MIDI compatible devices can be connected together easily
using MIDI cables. Once connected, performance data can readily be communicated between the two devices; or one can
make settings for, as well as control the operation of the other device.
Correspondence Between Commands and MIDI Messages
Normally, after power up (with V-LINK off), the LVS-400 outputs the corresponding MIDI messages from its MIDI OUT
when its buttons and knobs are operated.
Conversely, when any of the supported MIDI messages arrive at its MIDI IN, the LVS-400 performs the same functions
that it would if its buttons or knobs were operated.
* MIDI message values are in hexadecimal notation.
fig.17.e
14
LVS-400_e1.book 15 ページ 2004年1月20日 火曜日 午後12時50分
Control the LVS-400 from an External Device
Using V-LINK to Control the LVS-400
The LVS-400 can be placed under the control of V-LINK capable instruments and operated in sync with musical
performances (when V-LINK is on).
What is V-LINK?
V-LINK is a function that allows images to be synchronized to music. V-LINK makes it easy to manipulate images in a
variety of ways, while linking them to the expressive elements of a performance.
Using V-LINK
For details on how to turn V-LINK on/off, refer to the owner’s manual of the V-LINK compatible device that you intend
to connect to the LVS-400.
Use 10H as the LVS-400's Device ID in V-LINK messages.
The factory setting of V-LINK (receipt of V-LINK ON message only) is as follows.
Rx Channel
Tx Channel
Input Select
Transition Time (CC#5)
Transition Select
Output Fade
Video Fader (CC#11)
1
1
A ch: 1
B ch: 2
0.0 sec
1
Off
Main
15
LVS-400_e1.book 16 ページ 2004年1月20日 火曜日 午後12時50分
MIDI Implementation Chart
VIDEO MIX/LIVE SWITCHER
Date : Jan. 9, 2004
MIDI Implementation Chart
Model LVS-400
Transmitted
Function...
Recognized
Basic
Channel
Default
Changed
1–16
1–16
1–16
1–16
Mode
Default
Messages
Altered
Mode 3
X
Mode 3
X
Version : 1.00
Remarks
**************
Note
Number : True Voice
X
X
36, 38, 40, 41, 43, 45, 47, 48
O
Operational only
when Note Mode in ON
Velocity
Note On
Note Off
X
X
O
X
After
Touch
Key's
Channel's
X
O
X
O
Control Various Values
O
O
Control Various Values
O
O
O
O
O
O
O
O
Bank Select
Control Various Values
Control Various Values
Control Various Values
Pitch Bend
0, 32
1–5
7–31
64–95
Control
Change
O
O
0–3, 0–7
0–3, 0–7
Input Select : 1–4
Effects Mode : 1–8
System Exclusive
X
O
Control Various Values, V-LINK
: Song Position
System
: Song Select
Common
: Tune Request
X
X
X
X
X
X
: Clock
System
Real Time : Commands
X
X
O
O
X
: All Sound Off
: Reset All Controllers X
Aux
X
: Local On/Off
Messages : All Notes Off
X
O
: Active Sensing
X
: System Reset
X
X
X
X
O
X
Program
Change
: True Number
Start, Continue
Notes
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
16
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
O : Yes
X : No
LVS-400_e1.book 17 ページ 2004年1月20日 火曜日 午後12時50分
Troubleshooting
If you think there may be a problem with the device, first check the following points. If after checking these points the
problem persists, consult your dealer or local Roland Service.
Image not switching when fader is moved
If the same input is selected for both MAIN and INSERT while the EFFECTS MODE is set to OFF, moving the video fader
to switch the images will not change the image that is output.
In addition, switching the main input while the insert effects are in use automatically cancels the insert effects, so to start
using the insert effects again, first tilt the video fader completely to the MAIN side. Begin the insertion with the fader
tilted all the way to MAIN.
Image not switching when main input is switched
Are you looking at a display connected to MONITOR OUT? Select OUTPUT in the Monitor Select buttons. Alternatively,
you can connect the display to OUTPUT (the video output connector).
Images not switching as intended when the input is switched
You cannot use the same input simultaneously with both the composite and S-VIDEO connectors. The S-VIDEO takes
priority in this case.
No picture, even though source device is producing a signal
Is the Output Control button switched off (flashing)? If it is switched off, the screen will be black. Press the flashing
Output Control button to switch it to ON (lit), and the images are then output.
Transition effects not working
When the TIME setting knob is set near "0," no transition effect is attained when the main image is switched. You can
obtain the effect by using a longer time setting.
In addition, if the unit is not operating as you expect, first connect a display to the output of the device connected to the
LVS-400's input connector and confirm that the images are being output correctly.
17
LVS-400_e1.book 18 ページ 2004年1月20日 火曜日 午後12時50分
Specifications
LVS-400: VIDEO MIX / LIVE SWITCHER
Video Format
NTSC or PAL (ITU601)
Video Sampling Rate
13.5 MHz, 4:2:2 (Y: B-Y: R-Y), 8 bits
Dimensions
365 (W) x 259 (D) x 87 (H) mm
14-3/8 (W) x 10-1/4 (D) x 3-7/16 (H) inches
* Maximum height (top of T-bar): 118 mm / 4-11/16 inches
Weight (excluding the AC adaptor)
2.95 kg
Frame Synchronizer
6 lbs 9 oz
2
Accessories
Video Input
Owner’s Manual
S-Video: 4-pin mini DIN type x 4
AC Adaptor (PSB-1U)
Video (Composite): BNC type x 4
BNC-RCA Adapter x 4
* If S-Video is simultaneously, S-Video takes priority
Video Output
S-Video: 4-pin mini DIN type x 1
Video (Composite): BNC type x 2
Monitor Output
Video (Composite): BNC type x 1
Input/Output Level and Impedance
S-Video Luminance signal: 1 Vp-p, 75 ohms
Chrominance signal: 0.286 mVp-p, 75 ohms (NTSC),
0.3 mVp-p, 75 ohms (PAL)
Video (Composite): 1 Vp-p, 75 ohms
Control Connectors
MIDI IN: 5-pin DIN type
MIDI OUT: 5-pin DIN type
Transition Effects
Mix (Dissolve)
Wipe 1
Wipe 2
Composite Effects
Picture-in-Picture (4 types)
Luminance Key (2 types)
Chroma Key
Power Supply
DC 9 V (AC Adaptor)
Current Draw
1500 mA
18
962a
* In the interest of product improvement, the specifications
and/or appearance of this unit are subject to change
without prior notice.
LVS-400_e1.book 19 ページ 2004年1月20日 火曜日 午後12時50分
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
For EU Countries
This product complies with the requirements of European Directive 89/336/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Download PDF

advertising