Specifications | Eicon Networks DM/V600A-2E1-PCI Network Card User Manual

Physical Description
CH4 CH3 CH2 CH1
8
Red
Yellow
Green
Loopback
®
Dialogic
DM/V600A-2E1-PCI
7
6
Media Board
Quick Install Card
9
5
Part Number 64-0074-02
Copyright © 2001-2007
Dialogic Corporation.
All rights reserved.
10
4
3
2
1
1
2
Before You Begin
JP2A
JP2B
Protecting the Board from Damage
CAUTION: All computer boards are sensitive to
electrostatic discharge (“ESD”). Handle all staticsensitive boards and components at a static-safe work
area, and observe anti-static precautions at all times.
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall to learn more.
Unpacking the Board
®
Unpack the Dialogic DM/V600A-2E1-PCI Media Board
(“board”) according to the following steps:
1. Prepare a static-safeguarded work area.
2. Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the
board’s components.
3. Lay the board on the static-dissipative work
surface.
Note: Place boards in static-shielding bags when
carrying boards from station to station.
CAUTION: Do not remove the board from the anti-static
packaging until you are ready to install it. Observe
proper anti-static precautions at all times.
Configuring the Hardware
Board Identification
The device driver, part of the system software, assigns
board instance numbers in ascending order (beginning
with 0) as it detects each board in your system. A board
instance number is the identification (ID) number used by
the system software to recognize the board.
Note: If you add or remove a board, the system may
change the existing board instance numbers, depending
upon the PCI bus and slot number where the board is
installed or removed.
Windows Systems
Leave SW1 set to the factory default of 0 to let the
system automatically assign board instance numbers by
PCI bus slot number.
After the hardware and the system software are installed,
refer to the Dialogic® Configuration Manager (DCM)
utility to retrieve the assigned board instance ID
number(s). For more information about board
identification, see the DCM online help.
1. RJ-48C jacks: Connectors to external
digital telephone network interface.
2. General Network Interface Alarm LED
3. Power LED
4. Reset LED
5. SW1: Rotary switch to set board
identification (Linux systems only).
6. Alarm LEDs: During power-up, indicate
Power on Self Test (POST) status. During
operation CH1 and CH2 LEDs indicate
network alarms for each trunk.
Red—Alarm to indicate loss of signal
Yellow—Alarm to indicate loss of frame
synchronization at far end of external
network
Green—Indicates signal present; powered
up and receiving signal from external E1
sources
Loopback—Indicates loopback mode is
activated
7. CT Bus/MVIP Bus Termination Jumpers:
Bus signal is terminated when the
corresponding jumper clip is installed.
Note: Signal must be terminated only on
boards at each end of the CT Bus cable.
JP2A—CT Bus termination jumper
JP2B—MVIP Bus termination jumper
8. P3: CT Bus connector
9. ISA Edge Retainer
10.Signal Processing Daughterboard
Linux Systems
In a Linux system, you must set SW1 to a unique
number for each installed board. Use a non-magnetic
screwdriver to turn SW1 to one of 16 board ID settings,
0–9 or A–F.
After the hardware and the system software are installed,
refer to the proper configuration files to retrieve the
assigned board instance ID number(s). For more
information about Linux configuration files, see the
Dialogic® System Software documentation.
Installing the Hardware
1. With your computer on the static-safe work area,
switch off the power and disconnect all power cords
from the electrical outlets.
2. Remove the computer cover.
3. Select an empty PCI expansion bus slot and remove
the slot’s retaining screw and access cover plate (if
applicable).
4. If you are not installing your board in an ISA form
factor PCI slot, remove the ISA edge retainer.
5. Using the slot’s board guides, insert the board’s edge
connector into the bus slot. Press firmly until the
board is securely seated in the slot.
Installing the CT Bus Cable
Colored
Stripe
(Pin 1)
CT Bus
Cable
Installing a PCI Board
Remove
Cover
Plate
Returning a Product
PCI
Board
Computer
Chassis
32-Bit
PCI Slot
16-Bit
ISA Slot
6. Replace and tighten the slot’s retaining screw to
secure the board firmly in the chassis (if applicable).
7. Connect external digital telephone cables to the
RJ-48C jacks on the board bracket. The topmost
RJ-48C jack is for trunk 1 and the second RJ-48C
jack is for trunk 2.
Pinouts for the RJ–48C
Jacks on Bracket
Network Interface
Cable Connector
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
RCV_RING
RCV_TIP
CHASSIS GROUND
XMIT_RING
XMIT_TIP
CHASSIS GROUND
CHASSIS GROUND
CHASSIS GROUND
Pin 1
8. Repeat steps 3-7 for each additional board you are
installing.
9. Use the CT Bus cable to connect the board(s) you
are installing to other boards in the system. To
preserve the electrical integrity of the CT Bus, use a
CT Bus cable with the appropriate number of
connectors (“drops”). It is recommended that no more
than two connectors at either end of the cable be left
unused.
10. Your system may include both CT Bus and SCbus
boards. To connect both board types, you must
install a CT Bus/SCbus Adapter on one of the CT
Bus boards in a system. See the CT Bus/SCbus
Adapter Quick Install Card for installation details
about the Adapter and the bus cables
Dialogic also provides direct support via Dialogic® Pro™
Services agreements. For more details of direct support
from Dialogic please refer to:
http://www.dialogic.com/support/DialogicPro.
Note:
Your CT Bus cable may
have a different number
of connectors (drops).
11. Install CT Bus Termination Jumpers only on boards
located at each end of the CT Bus cable. See the
“Physical Description” section for jumper details.
12. Replace the computer’s cover when finished and
reconnect the power cords.
13. Turn the computer’s power ON.
CAUTION: If your BIOS is set to use Plug and Play
technology and there are ISA boards in your system, an
IRQ conflict can be created if a PCI board is assigned
the same IRQ as an ISA board. This could cause the
machine to stop responding. You can prevent this by
entering the BIOS and reserving the appropriate IRQs
(those used by your ISA boards) for ISA use only.
After Installing the Hardware
After installing the hardware, run the Dialogic®
Configuration Manager (DCM) as described in the
installation instructions included with the Dialogic®
System Software to configure your system.
For technical specifications and product information go
to: http://www.dialogic.com/products.htm.
Warranty and Return Information
Warranty Period
For specific warranty information for this board, refer to
the Warranty section of the Products page, located at
this URL: http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products
through a network of value added distributors who are
trained to answer technical questions on installing and
configuring Dialogic® products. If you are unsure how
to contact your support channel, please call Dialogic
in the United States at 973-967-6600 (9am-5pm EST)
and we will assist in obtaining the appropriate support
channel. Outside the United States please refer to
http://www.dialogic.com/support/contact .
To return a board for warranty or any other returns,
please refer to the following:
http://www.dialogic.com/support/hwfaults .
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales Office
for your area. Address, telephone and fax numbers, are
available at the Dialogic website located at:
http://www.dialogic.com/contact.htm. To purchase
®
Dialogic products, please refer to the following website
to locate the appropriate supplier:
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are subject to
change without notice and do not represent a commitment on the part of Dialogic Corporation
or its subsidiaries (“Dialogic”). Reasonable effort is made to ensure the accuracy of the
information contained in the document. However, Dialogic does not warrant the accuracy of
this information and cannot accept responsibility for errors, inaccuracies or omissions that may
be contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH
DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU
AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND
DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO
SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY
RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life sustaining, critical
control or safety systems, or in nuclear facility applications.
It is possible that the use or implementation of any one of the concepts, applications, or ideas
described in this document, in marketing collateral produced by or on web pages maintained
by Dialogic may infringe one or more patents or other intellectual property rights owned by
third parties. Dialogic does not provide any intellectual property licenses with the sale of
Dialogic products other than a license to use such product in accordance with intellectual
property owned or validly licensed by Dialogic and no such licenses are provided except
pursuant to a signed agreement with Dialogic. More detailed information about such
intellectual property is available from Dialogic’s legal department at 9800 Cavendish Blvd., 5th
Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to
procure all necessary intellectual property licenses required to implement any concepts
or applications and does not condone or encourage any intellectual property
infringement and disclaims any responsibility related thereto. These intellectual property
licenses may differ from country to country and it is the responsibility of those who
develop the concepts or applications to be aware of and comply with different national
license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, among others, are either
registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly
only with permission from Dialogic. Such permission may only be granted by Dialogic’s legal
department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any
authorized use of Dialogic's trademarks will be subject to full respect of the trademark
guidelines published by Dialogic from time to time and any use of Dialogic’s trademarks
requires proper acknowledgement. The names of actual companies and products mentioned
herein are the trademarks of their respective owners.
Download PDF

advertising