Owner`s manual | Eiki LC-XC1 CRT Television User Manual

MULTIMEDIA PROJECTOR
MODEL
LC-XC1
OWNER’S MANUAL
LC-XC1
TO THE OWNER
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables
you to manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or
other accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable
connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem
still persists, contact the sales dealer where you purchased the projector or the service center.
SAFETY PRECAUTIONS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
• This projector produces intense light from the projection lens. Do not stare directly into the lens as
possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.
• This projector should be set in the way indicated. If not, it
may result in a fire hazard.
• Take appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum distance should be taken. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.
• Do not put any flammable object or spray can near the projector, hot air is exhausted from the
ventilation holes.
• The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function
from the Laser Light Window while pressing the LASER button (for 1. minute). Do not look into the
Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.
• If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT
DANGEROUS
VOLTAGE CONSTITUTING A RISK OF
ELECTRIC
SHOCK IS PRESENT WITHIN THIS
UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT
OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE
OWNER’S MANUAL WITH THIS UNIT.
2
LC-XC1
SAFETY INSTRUCTIONS
All the safety and operating instructions should be
read before the product is operated.
ventilation is provided.
Never push objects of any kind into this projector
Read all of the instructions given here and retain
them for later use. Unplug this projector from AC
power supply before cleaning. Do not use liquid or
aerosol cleaners, Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the
projector.
For added protection to the projector during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet. This will prevent damage due to
lightning and power line surges.
Do not expose this unit to rain or use near water...
for example, in a wet basement, near a swimming
pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart,
stand, or table. The projector may fall, causing
serious injury to a child or adult, and serious
damage to the projector. Use only with a cart or
stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should
follow the manufacturer’s instructions, and should
use a mounting kit approved by the manufacturers.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to
overturn.
Slots and openings in the back and bottom of the
cabinet are provided for ventilation, to insure
reliable operation of the equipment and to protect it
from overheating.
The openings should never be covered with cloth or
other materials, and the bottom opening should not
be blocked by placing the projector on a bed, sofa,
rug, or other similar surface. This projector should
never be placed near or over a radiator or heat
register.
through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the
projector.
This projector should be operated only from the
type of power source indicated on the marking label. If
you are not sure of the type of power supplied, consult
your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything
to rest on the power cord. Do not locate this
projector where the cord may be damaged by
persons walking on it.
Do not attempt to service this projector yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Unplug this projector from wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
e. If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the
service technician has used replacement parts specified
by the manufacturer that have the same characteristics
as the original part. Unauthorized substitutions may
result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this
projector, ask the service technician to perform routine
safety checks to determine that the projector is in safe
operating condition.
This projector should not be placed in a built-in
installation such as a book case unless proper
3
LC-XC1
COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased
it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
LC-XC1
TABLE OF CONTENTS
DIRECT OPERATION
MENU OPERATION
FEATURES AND DESIGN
PREPARATION
6
7
NAME OF EACH PART OF THE PROJECTOR7
SETTING-UP THE PROJECTOR
8
CONNECTING THE AC POWER CORD
POSITIONING THE PROJECTOR
ADJUSTABLE FEET
MOVING THE PROJECTOR
8
9
10
10
CONNECTING THE PROJECTOR
11
TERMINALS OF THE PROJECTOR
11
CONNECTING TO THE VIDEO EQUIPMENT13
CONNECTING TO THE COMPUTER
14
COMPUTER MODE
24
SELECTING COMPUTER MODE
SELECTING COMPUTER SYSTEM
24
24
COMPATIBLE COMPUTER SPECIFICATIONS
PC ADJUSTMENT
PICTURE IMAGE ADJUSTMENT
NORMAL FUNCTION
15
TOP CONTROLS AND INDICATORS
15
OPERATION OF THE REMOTE CONTROL 16
OPERATING RANGE
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE THE ON-SCREEN MENU
25
26
28
29
29
AUTO IMAGE FUNCTION
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
30
31
VIDEO MODE
32
SELECTING VIDEO MODE
SELECTING VIDEO SOURCE
32
32
VIDEO SIGNAL FROM VIDEO OR S-VIDEO JACK
VIDEO SIGNAL FROM Y, Pb/Cb, Pr/Cr JACKS
BEFORE OPERATION
23
23
SELECTING COLOR SYSTEM
PICTURE IMAGE ADJUSTMENT
NORMAL FUNCTION
32
32
33
34
35
PICTURE SCREEN ADJUSTMENT
35
SETTING
36
SETTING MENU
SETTING LANGUAGE
36
37
16
17
18
FLOW OF ON-SCREEN MENU
MENU BAR
18
18
19
BASIC OPERATION
20
APPENDIX
38
TURNING ON 70FF THE PROJECTOR
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
20
21
OPERATING WIRELESS MOUSE
MAINTENANCE
38
39
LENS SHIFT ADJUSTMENT
KEY STONE ADJUSTMENT
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
P-TIMER FUNCTION
SOUND ADJUSTMENT
21
21
21
22
22
22
22
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
LAMP REPLACEMENT
LAMP REPLACEMENT MONITOR TIMER
CLEANING THE PROJECTION LENS
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
39
39
40
40
41
42
44
23
TRADEMARKS
• Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
• IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
• Windows and PowerPoint are registered trademarks of Microsoft Corporation.
• Each name of corporations or products in the owner’s manual is a trademark or a registered trademark of
its respective corporation.
5
FEATURES AND DESIGN
LC-XC1
This Multimedia Projector is designed with the most advanced technology for portability, durability, and
ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and
matrix liquid crystal display (LCD) technology.
♦ Compatibility
This projector widely accepts various video and
computer input signals including;
• Computers
IBM-compatible and Macintosh computers up to
1280 x 1024 resolution.
• 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.
• Component Video
Component video signals, such as a DVD
player output high definition TV signals including
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 or
1080i-60, can be connected.
• S-Video
S-Video signals, such as a S-VHS VCR output
signals, can be connected.
♦ High Resolution Image
This projector provides 1024 x 768 dots
resolution for computer input and 700 horizontal
TV lines. The resolution from the computer between
XGA (1024 x 768) and SXGA (1280 x 1024) is
compressed into 1024 x 768 dots. This projector
cannot display image of over 1280 x 1024 dots.
When the resolution of your computer is over than
1280 x 1024, reset the computer output for lower
resolution.
♦ Multi-Scan System
This projector has Multi-Scan System to
conform to almost all computer output signals
quickly. There is no need for troublesome manual
adjustment of frequency and other settings.
♦ One-Touch Auto Imaging
Incoming computer video signals are recognized
and the best setting is automatically selected by the
Auto Image function. No complicated setup is
necessary and projection is always precise.
♦ Progressive Scan Function
This function converts interlace video signals into
progressive scan signals and provide fine
picture quality.
Multilanguage Menu Display
Operation menu is displayed in; English, Deutsch,
Francais, Italiano, Espanol, or Japanese.
♦ • Digital Zoom (Computer Mode only)
The Digital Zoom magnifies the image up to 49
times, allowing you to focus on crucial
information at a presentation.
♦ Motor-driven Lens Shift
The projection lens can be moved up and down with
the motor-driven lens shift function. This function
makes it easy to provide the projected image
where you want.
The zoom and focus can be also adjusted with
motor-driven operation.
♦ Keystone Correction
Positioning height of the projector may result in
distorted images being displayed in a trapezoid
shape. Keystone Correction solves this problem
by digitally altering the projection to produce
undistorted images.
♦ Power Management
Power Management function is provided to
reduce power consumption while the projector is
not in use.
This Power Management function operates to turn
the Projection Lamp off when the projector detects
signal interruption and any button is not pressed over
5 minutes. The Projection Lamp is automatically
turned on again when the projector detects the signal
or any operation button is pressed.
This projector is shipped with this function ON.
♦ Digital Visual Interface
This projector is equipped with the DVI 24-pin
terminal for connecting DVI output of the
computer.
♦ Laser Pointer Function
The Remote Control Unit supplied with this projector
includes the Laser Pointer function. This function
helps you to make a smart presentation on a
projected screen.
♦ Wireless Mouse
The Remote Control Unit supplied with this projector
has Wireless Mouse function for the connected
computer.This function enables you to operate both
projector and computer with this Remote Control
Unit only.
6
LC-XC1
7
LC-XC1
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V or
200-240 V AC. The projector automatically selects the
correct input voltage. It is designed to work with singlephase power systems having a grounded neutral conductor.
To reduce the risk of electrical shock, do not plug into any
other type of power system.
Consult your authorized dealer or service station if you are
not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment before
turning the projector on. (Refer to pages 11 14 ror
connection.)
CAUTION
For safety, unplug the AC Power Cord when the
appliance is not used.
When this projector is connected to the outlet
with the AC Power Cord, the appliance is in
Stand-by Mode and consumes a little electric
power.
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector
Confirm the AC plug type with the chart below. The proper AC power cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Projector side
AC Outlet side
8
LC-XC1
POSITIONING THE PROJECTOR
• This projector is designed to project on a flat
projection surface.
• The projector can be focused from 4.6’ (1 .4m)
47.3’ (1 4.4m),
• Refer to the figure below to adjust the screen
size.
ROOM LIGHT
The brightness in the room has a great
influence on the picture quality. It is
recommended to limit ambient lighting in
order to provide the best image.
LENS SHIFT ADJUSTMENT
The projection lens can be moved up and down with the motor-driven lens shift function. This function
makes it easy to provide the projected image where you want. The U/D ratio can be adjusted 10 : 0 1: 3
(refer to the figure below.). Refer to P 21 for operation.
9
LC-XC1
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET. Projection angle can be
adjusted to 9.0 degrees.
1
Lift the front of the projector and pull the FEET LOCK
LATCHES on both sides of the projector.
2
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET
to fine tune the position and the tilt.
3 To shorten the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
The position and the keystone distortion of the image can
be adjusted using the Menu Operation. (Refer to P 22,
31 and 35.)
MOVING THE PROJECTOR
Use the Carry Handle when moving the Projector. When
moving the projector, replace the lens cover and retract the
feet to prevent damage to the lens and cabinet.
When this projector is not in use for an extended period, put it
into the case (dust cover) supplied with this projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
• Do not drop or bump the projector, otherwise damages or malfunctions may result.
• When carrying the projector, use a suitable carrying case.
• Do not transport the projector by using a courier or transport service in an unsuitable transport
case. This may cause damage to the projector. To transport the projector through a courier or
transport service, consult your dealer for best way.
10
LC-XC1
This projector has INPUT TERMINALS and OUTPUT TERMINALS on its side for connecting computers
and video equipment. Refer to the figure on pages 11 to 14 and connect properly.
INPUT TERMINALS
11
LC-XC1
OUTPUT TERMINALS
RESET BUTTON
This projector uses a micro processor to control the
R/C JACK
When using the Wired / Wireless
unit. Occasionally, the micro processor may
malfunction and need to be reset. This can be done
by pressing the RESET button with a pen, which will
shut down and restart the unit. Do not use the
Remote Control Unit as the Wired
Remote Control, Connect the Wired
Remote Control Unit to this jack with
the Remote Control Cable (supplied).
RESET function excessively.
(Refer to page 17.)
COMPUTER MONITOR OUTPUT
JACKS (BNC X 5)
These jacks output the signal from
the COMPUTER INPUT terminals
(except the digital input signal).
AUDIO OUTPUT JACKS
Connect an external audio
amplifier to these jacks.
(Refer to P13,14.)
VIDEO MONITOR OUTPUT JACK
This terminal outputs the composite video
I
signal or the signal from the S-VIDEO
NPUT JACK. Connect an external
Monitor to this jack. (Refe rto P13.)
Connect an external monitor to
these jacks. (Refer to P14.)
12
LC-XC1
13
LC-XC1
14
LC-XC1
INDICATORS
TOP CONTROL
15
LC-XC1
LASER POINTER FUNCTION
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window, When the LASER button
is pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is
released, light goes off. Laser light is emitted with the RED light which tells the laser beam being emitted.
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on
yourself or other people. The three marks bellow are the caution labels for the laser beam.
CAUTION :
Use of controls or adjustments or performance of procedures other than those specified herein
may result hazardous radiation exposure.
16
LC-XC1
Remote Control Batteries Installation
1. Remove the battery
compartment lid.
•
•
•
•
•
2.
Slide the batteries into the
compartment.
3.
Replace the
compartment lid.
•
•
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the Remote Control Unit to moisture, or heat.
Do not drop the remote control unit.
If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
17
LC-XC1
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through the ONSCREEN MENU. Refer to the following pages to operate each
adjustment in the ON-SCREEN MENU.
Move the pointer (see the NOTE below) by pressing POINT
button(s) on the TOP CONTROL or the REMOTE CONTROL.
Select the item by pressing SELECT button.
NOTE: Pointer is the icon on the ON-SCREEN MENU to
select the item. See the figures on the section
‘FLOW OF ON-SCREEN MENU' below.
FLOW OF ON-SCREEN MENU
Display ON-SCREEN MENU
1
2
3
4
5
Press MENU button to display the ON-SCREEN
MENU
(MENU BAR). The red frame is the POINTER.
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT I LEFT
buttons.
Select the ITEM by pressing SELECT button. The
dialog box of the ITEM appears.
Move the POINTER downward by pressing POINT
DOWN button. (The shape of the POINTER becomes
an arrow.)
Move the POINTER to the ITEM that you want to
adjust and adjust the ITEM by pressing SELECT
button. Refer to the following pages for details of
respective adjustments.
18
LC-XC1
MENU BAR
MENU BAR IN COMPUTER MODE Press MENU BUTTON while in Computer mode.
MENU BAR IN VIDEO MODE Press MENU BUTTON while in Video Mode.
19
LC-XC1
TURNING ON THE PROJECTOR
1.
2
Complete the peripheral connections (with Computer, VCR, etc.) before turning on the projector. (Refer to
“CONNECTING TO THE PROJECTOR” on Pages 11-~14 for
connecting that equipment.)
Connect the projector’s AC Power Cord into a wall outlet and
turn the MAIN ON I OFF SWITCH to ON. The LAMP
indicator
lights RED, and the READY indicator lights GREEN.
3
Press the POWER ON-OFF button on the Remote Control
Unit or on the Top Control to ON. The LAMP indicator dims,
and the Cooling Fans start to operate. The Preparation
Display
appears on the screen and the count-down starts. The signal from the source appears after 30 seconds.
TURNING OFF THE PROJECTOR
1.
2
Press the power ON-OFF button on the Remote Control Unit or on the Top Control, and the message “Power
off?” appears on the screen.
Press the power ON-OFF button again to turn off the projector.
The LAMP indicator lights bright and the READY indicator turns
off. After the projector is turned off, the Cooling Fans operate (for
about 90 seconds). During this “Cooling Down” period, this
appliance cannot be turned on.
3
When the projector has cooled down, the READY indicator
turns to green again and you can turn the projector on. After
cooling down completely, turn the MAIN ON I OFF SWITCH to
OFF and disconnect the AC power cord.
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU
TURN THE PROJECTOR ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When the Power Management function is ON, the Projector detects the signal interruption and turns the Projection
Lamp off automatically. Refer to “Power Management” on page 33.
When WARNING TEMP. indicator flashes red, the projector is automatically turned oft. Wait at least 5 minutes
before turning the projector on again.
When WARNING TEMP indicator continues to flash, follow procedures below:
1. Turn the MAIN ON I OFF SWITCH to OFF and disconnect the AC power cord from the AC outlet.
2. Check the air filters for dust accumulation.
3. Clean the Air Filter. (See “AIR FILTER CARE AND CLEANING” section on page 39.)
4. Turn the Projector on again.
If WARNING TEMP indicator should still continue to flash, contact the sales dealer where you purchased this
projector or service center.
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working,
WARNING TEMP. INDICATOR flashes red.
20
LC-XC1
ZOOM ADJUSTMENT
1
Press the ZOOM !/"button(s) on the Top Control or on
the Remote Control Unit. The message “Zoom” is displayed.
2.
Press the ZOOM ! button or the POINT UP button to
make the image larger, and press the ZOOM " button or
the POINT DOWN button to make the image smaller.
FOCUS ADJUSTMENT
1
Press the FOCUS !/"button(s) on the Top Control or on the
Remote Control Unit. The message “Focus” is displayed.
2
Adjust the focus of the image by pressing the FOCUS
!/" button(s) or the POINT UP/DOWN button(s).
LENS SHIFT ADJUSTMENT
1
Press the LENS SHIFT !/" button(s) on the Top Control
or the LENS SHIFT button on the Remote Control Unit.
The message “Lens shift” is displayed.
2
Press the LENS SHIFT ! button or the POINT UP button to
move the image up, and press the LENS SHIFT " button or the
POINT DOWN button to move the image down.
Refer to P9 for operating range.
21
LC-XC1
KEYSTONE ADJUSTMENT
If the picture has keystone distortion, correct image with KEYSTONE adjustment.
1.
2
Press the KEYSTONE !/"button on the Remote Control Unit
or select the Keystone on the SCREEN MENU. (Refer to
page 31, 35.) The message “Keystone” is displayed.
Correct the Keystone distortion by pressing the KEYSTONE
!/"button or the POINT UP/DOWN button(s). Press the
KEYSTONE ! button or the POINT UP button to reduce the upper
part or the image, and press the KEYSTONE " button or the
POINT DOWN button to reduce the lower part.
NO SHOW FUNCTION
Press the NO SHOW button on the Remote Control Unit to black
out the image. This function is cancelled when the NO SHOW
button is pressed again or any other function button is pressed.
PICTURE FREEZE FUNCTION
Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is
cancelled when the FREEZE button is pressed again or any other function button is pressed.
P-TIMER FUNCTION
Press the P-TIMER button on the Remote Control unit. The timer display “00 : 00” appears on the screen and the
timer starts to count the time (00 : 00 59 : 59). To stop the P-TIMER, press the
P-TIMER button. And then, press the P-TIMER button again to cancel the
P-TIMER function.
22
LC-XC1
DIRECT OPERATION
Press the VOLUME (+1—) button(s) on the Top Control or
on the Remote Control Unit to adjust the volume. The Volume
dialog box appears on the screen for a few seconds.
(+) button to increase the volume, and (—) button decreasing.
Press the MUTE button on the Remote Control Unit to cut
oft the sound. To restore the sound to its previous level,
press the MUTE button again or press Volume (+/—)
button(s).
MENU OPERATION
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to
select SOUND and press the SELECT button.
Another dialog box SOUND MENU will appear.
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to select by
pressing the POINT UP/DOWN buttons.
Move the arrow to ! or " of “Volume” by pressing the POINT UP/ DOWN buttons. To increase the volume, point the
arrow to A and then press the SELECT button. To decrease the volume point the arrow to V and then press the
SELECT button.
To cut off the audio sound, point the arrow to “Mute” and then press the SELECT button. The Mute display is changed
On from Off and the sound is cut off. To restore the sound to its previous volume level, set the Mute to Off.
23
LC-XC1
DIRECT OPERATION
Select COMPUTER mode by pressing the MODE button on
the Top Control or the COMPUTER button on the Remote
Control Unit.
MENU OPERATION
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
Computer and press the SELECT button. Another dialog
box MODE MENU will appear.
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the mode either Computer 1
or Computer 2, and then press the SELECT button.
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display
appears to show the information of the computer being
selected.
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of
computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page
25). When selecting Computer, this projector automatically
tunes to the incoming signal and projects the proper image
without any special settings. (Setting of the Computer System
may be required when connecting some computers.)
Note : The projector may display one of the following messages.
Go to PC adj
I The projector cannot discriminate or detect the input
signal from the computer. Adjust and set the
computer system manually. (Refer to page 26.)
No signal
I
There is no signal input from the computer. Make
sure the connection of the computer and the
projector is set correctly.
(Refer to TROUBLESHOOTING on page 42.)
SELECT COMPUTER SYSTEM MANUALLY
To set the Computer system manually, select the mode on the
ON-SCREEN MENU.
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
SYSTEM MENU will appear.
2 Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the system that you want to
set, and then press SELECT button.
24
LC-XC1
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below
and less than 180 MHz of Dot Clock.
When the input signal is from the COMPUTER INPUT-i (DIGITAL) terminal, refer to the chart below.
NOTE: Specifications are subject to change without notice.
25
LC-XC1
This Projector can automatically tune to the display signals from most personal computers currently
distributed. However, some computers employ special signal formats which are different from the standard
ones and may not be tuned by the Multi-Scan system of this projector. If this happens, the projector cannot
reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized
picture, a non-centered picture or a skewed picture.
This projector has a PC ADJUSTMENT function to enable you to precisely adjust several parameters to
match with those special signal formats. This projector has 8 independent memory areas to memorize those
parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use
it.
Note : This PC ADJUSTMENT function cannot be operated when the input signal is from the COMPUTER INPUT-i
(DIGITAL) terminal or “RGB” is selected on SYSTEM MENU (P24 and 25).
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT RIGHT/LEFT button to select PC
ADJUST and press the SELECT button. Another dialog
box “Where to reserve” MENU will appear.
2
In this dialog box, you can store the parameter into the area from
“Mode 1” to “Mode 8.” When memorizing the new computer
parameter, select the Mode with the message “Free” by pressing
the POINT UP/DOWN button and the SELECT button. To
change the parameters of the Mode previously set, select the
Mode with “Stored.”
3
When the Mode is selected, Parameter adjustment dialog box
appears. Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN button, and adjust each item by
pressing the SELECT button to match with your computer.
4 Move the arrow to “Stored” and press the SELECT button. The
parameter is memorized in the selected Mode.
5 To activate the Mode manually adjusted in this PC
ADJUSTMENT MENU, select the Mode at SYSTEM SELECT
MENU. (Refer to page 24.)
26
LC-XC1
The number of the total vertical lines. Adjust the number to match
the image of your personal computer.
The number of the total dots in one horizontal period. Adjust the
number to match the image of your computer.
Adjustment of the horizontal or vertical picture position. When the
image is not centered on the screen, adjust each of those
items.
Adjustment of the clamp level. When the image has a dark
bar(s), try this adjustment.
Adjust the picture as necessary to eliminate flicker from the
display.
Adjustment of the area displayed with this projector. Select the
resolution at the Display area dialog box, or adjust the number
at the column of “H” or “V” to match the resolution of the
image.
Adjustment 01 tne norizontai height or vertical wicitn 01 tne
image.
NOTE : The Display area, the Horiz. scale and the Vert. scale
cannot be adjusted when “HDTV1O35i” or “HDTV1O8Oi”
is
selected on SYSTEM MENU (P24 and 25).
Each of the keys operates as follow.
Reset
Mode free
Stored
Recalls the parameter data that was
previously
adjusted.
•.
I
Quit
I
Clears the parameter data previously set.
Stores the parameters in the memory.
Closes PC ADJUST MENU.
27
LC-XC1
1
2
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
IMAGE MENU will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to
select and then press SELECT button.
Normal picture level preset on this projector. This picture level
can be set by pressing the NORMAL button.
Picture level adjusted for the picture with fine tone.
Picture level adjusted manually in the custom setting dialog
box.
When selecting “",” the custom setting dialog box will
appear. Move the arrow to the item that you want to
change by pressing the POINT UP/DOWN button, and
adjust each value by pressing the SELECT button to match
with the image.
Adjust the picture as necessary to eliminate flicker trom
the display. (From 0 to 127.)
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
Move the arrow to the color that you want to adjust. Point
to " to lighten the color and select ! to deepen the color.
(From 0 to 63.)
Point to " to decrease contrast, and select ! to increase
contrast. (From 0 to 63.)
Point to "to adjust the image darker, and select ! to adjust
brighter. (From 0 to 63.)
Point to " to soften the image, and select ! to sharpen the
image (From 0 to 15.)
Each of the keys operates as follow.
Reset
Recalls the data previously adjusted.
Stored
Stores the adjusted data in the memory.
Quit
Closes IMAGE MENU.
NOTE:
The Fine sync and the Total dots
cannot be operated when the input signal
is from the COMPUTER INPUT-i
(DIGITAL) terminal or “RGB” is selected
on SYSTEM MENU (P24 and 25).
The Fine sync and the Total dots cannot
be fully adjusted when “HDTV1O35i” or
“HDTV1O8Oi” is selected on SYSTEM
MENU (P24 and 25).
28
LC-XC1
NORMAL FUNCTION
The normal picture level is preset on this projector at the
factory and can be restored anytime you press the NORMAL button
(located on the Top Control or on the Remote Control Unit).
The “Standard” display will be displayed on the screen for a few
seconds.
The Auto Image function is provided to automatically adjust
Fine sync., Total dots, and Picture Position for most
computers.
1
2
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to
select AUTO IMAGE and press the SELECT button. Another dialog box AUTO IMAGE MENU will appear.
Move the arrow to an item that you want to adjust by pressing
the POINT UP/DOWN button. Change the setting On or Off by
pressing the SELECT button.
Adjust the picture as necessary to eliminate flicker from the
display.
This item can be adjusted manually. (Refer to page 28.)
The number of the total dots in one horizontal period. This item can
be adjusted manually. (Refer to page 28.)
Adjustment of the position of the image. This item can be adjusted
manually. (Refer to page 30.)
3
Move the arrow to “Go!” and press the SELECT button to start
the Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE button on the Top Control or on the Remote Control
Unit.
Stored
Go!
Quit
....
Stores the On/Off setting of each item.
Starts the Auto Image Adjustment.
. ...
Closes AUTO IMAGE MENU.
NOTE: This menu cannot be operated when the input signal is from the COMPUTER INPUT-i (DIGITAL) terminal or
“RGB,” “HDTV72Op,” “HDTV1O35i” or “HDTV1O8Oi” is selected on SYSTEM MENU (P24 and 25).
The Fine sync., Total dots, and Picture Position of some computers may not be fully adjusted with the Auto
Image Function. In that case, manual adjustment is required to make fine image. (Refer to page 28 to adjust
“Fine sync.” or “Total dots” and page 30 to adjust Picture Position.)
29
LC-XC1
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
1
Press the MENU button and the ON-SCREEN MENU
appear. Press the POINT LEFT/RIGHT buttons to select
POSITION and press the SELECT button. Another dialog I
POSITION MENU will appear.
2 Select the arrow to the direction (described as #, $, %, or ⇪
that you want to adjust by pressing the POINT UP/DOV
LEFT/RIGHT buttons, and then press the SELECT
button.
Each of the keys operates as follow.
Reset
Recalls the setting data previously set.
Stores the setting data in the memory.
Closes
POSITION MENU.
30
LC-XC1
This projector has a picture screen resize function, which enables you to display the desirable image size.
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to
select SCREEN ~ and press the SELECT button.
Another dialog box SCREEN MENU will appear.
2
Press the POINT DOWN button and a red-arrow icon
will appear. Move the arrow to the function that you want
to select and then press SELECT button.
To make the image into its original size, select
True in the dialog box. When the original image size is larger
than the screen size (1024 x 768), the image can be panned by
pressing the POINT UP/DOWN/LEFT/RIGHT buttons.
When the image is distorted vertically, select
Keystone in the dialog box. The ON-SCREEN MENU and
SCREEN MENU disappears and the message “Keystone” is
displayed. Correct the Keystone distortion by pressing the
"button or the POINT UP/DOWN button(s).
KEYSTONE !/"
Refer to KEYSTONE ADJUSTMENT on page 20.
To adjust the image size or pan the image, select
Digital zoom in the dialog box. The ON-SCREEN MENU and
SCREEN MENU disappears, and the magnifying glass icon and
the message “D. Zoom” is displayed.
This projector also enters Digital Zoom mode by pressing the
D.ZOOM !/"
"button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ! button or
the SELECT button. The image is magnified by degrees.
NOTE
• The True and the Digital Zoom cannot be
operated when ‘RGB,” “HDTV1O35i” or
“HDTV1O8Oi” is selected on SYSTEM
MENU (P24 and 25).
• This projector cannot display any
resolution higher than 1280 X 1024. If your
computer’s screen resolution is higher than
1280 X 1024, reset the resolution to the
lower before connecting the projector.
• The image data in other than XGA (1024 x
768) is modified to fit the screen size in the
initial mode.
• The normal “Panning Operation” may not
function properly if the computer system
prepared with the “PC Adjust” is used.
Compress function
To compress the image size, press the D.ZOOM " button or
the RIGHT CLICK button. The size of image is reduced by
Panning function
degrees
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT
buttons. Panning function can work only when the image is larger
than the screen size.
To cancel Digital Zoom mode, press any button except D.ZOOM
!/"
", SELECT, RIGHT CLICK, or POINT button. To adjust the
image to 1024 x 768, press NORMAL button.
31
LC-XC1
DIRECT OPERATION
Select VIDEO mode by pressing the MODE button on the
Top Control or the VIDEO button on the Remote Control Unit.
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select Video
and press the SELECT button.
This projector automatically detects the signal from the
VIDEO INPUT JACK(s) or the S-VIDEO INPUT JACK.
When those jacks are connected at the same time, select
the type of Video source in VIDEO SOURCE MENU.
1
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select
VIDEO SOURCE and press the SELECT button. Another
dialog box VIDEO SOURCE MENU will appear.
2 Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the source that you want to
select, and then press the SELECT button.
Auto
The projector automatically detects the incoming Video source,
and adjusts itself to optimize its performance.
• When both VIDEO jack and S-VIDEO jack are connected, the
5-VIDEO jack has priority over the VIDEO jack.
• When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are
connected, the Y-Pb/Cb-Pr/Cr jacks have priority over the S-VIDEO jack.
Video I S-Video / Y, PbICb, Pr/Cr
When the VIDEO INPUT JACK(s) and the S-VIDEO INPUT JACK are connected at the same time, or if the projector
cannot chose the proper video source, it is necessary to select a specific video source among Video, S-Video
and Y, Pb/Cb, Pr/Cr.
32
LC-XC1
1
Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT
buttons to select SYSTEM and press the SELECT button. Another dialog box
VIDEO SYSTEM MENU will appear.
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to “Auto”, and then press the SELECT
button.
VIDEO SIGNAL FROM VIDEO JACK OR S-VIDEO JACK
Auto
The projector automatically detects the incoming Video system, and adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select the system
manually.
PAL I SECAM I NTSC I NTSC4.43 I PAL-M / PAL-N
If the projector cannot reproduce the proper video image, it is
necessary to select a specific broadcast signal format among
PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
VIDEO SIGNAL FROM Y, Pb/Cb, Pr/Cr JACKS
Auto
The projector automatically detects the incoming Video signal,
and
adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce the proper video image, it is
necessary to select a specific component video signal format
among 480i, 575i, 48Op, 575p, 720p, i035i and iO8Oi.
33
LC-XC1
1
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
IMAGE MENU will appear.
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to
select and then press SELECT button.
Standard
Normal picture level preset on this projector. This picture level
can be set by pressing the NORMAL button.
Cinema
Picture level adjusted for the picture with fine tone.
Custom
Picture level adjusted manually in the custom setting dialog box
When selecting “",” the custom setting dialog box will appear.
Move the arrow to the item that you want to change by pressing
the POINT UP/DOWN button, and adjust each value or change
the setting On or Off by pressing the SELECT button to match
with the image.
Color
Point to V button to lighten the image, and select A to
deepen image. (From 0 to 63.)
Tint
Point to V button to increase purple, and select A to increase
gre~ (From 0 to 63.)
White balance (Red I Green I Blue)
Move the arrow to the color that you want to adjust. Point
to V lighten the color and select A to deepen the color. (From 0
to 63.)
Contrast
Point to V button to decrease contrast, and select A to increa
contrast. (From 0 to 63.)
Brightness
Point to V button to darken the image, and select A to brighten
image. (From 0 to 63.)
Sharpness
Point to V button to soften the image, and select A to
sharpen image. (From 0 to 31.)
Noise reduction
Set “On” to reduce the noise (rough parts) of the image.
Progressive
Set “On” to provide progressive scan mode.
Each of the keys operates as follow.
Recalls the data previously adjusted.
Reset
Stored
....
Stores the data in the memory.
Quit Closes IMAGE MENU.
..
NOTE :
The Noise Reduction
cannot be operated when the video
signal is from the Y, Pb/Cb, Pr/Cr
jacks.
The Progressive cannot be operated
when “480p,” “575p,” “720p,” “1 035i,”
“1 080i-50” or “iO8Oi-60” is selected
on SYSTEM MENU (P33).
34
LC-XC1
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and can be restored anytime you press the
NORMAL button (located on the Top Control or on the Remote Control Unit). The “Standard” display will be
displayed on the screen for a few seconds.
This projector has a picture screen resize function, which enables you to display the desirable image size.
1
2
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SCREEN and press the SELECT button. Another dialog
box SCREEN MENU will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the screen size that you want
to set, and then press the SELECT button.
Regular
Normal Video Image size with 4 x 3 aspect ratio.
Wide
Resizes the image for wide screen size with 16 x 9 aspect ratio.
NOTE:The Regular and the Wide cannot
be operated when “720p,” “1035i,”
“1080i-50” or “1080i-60” is selected on
SYSTEM MENU (P33).
Keystone
When the image is distorted vertically, select Keystone in
the dialog box. Correct the Keystone distortion by pressing
KEYSTONE A/V button or POINT UP/DOWN button(s). Refer
to KEYSTONE ADJUSTMENT on page 20.
35
LC-XC1
1.
2
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SETTING and press the SELECT button. Another dialog
box SETTING MENU will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to set, and then
press the SELECT button to set it “On” or “Off” or press the
POINT LEFT/RIGHT button to adjust the value.
Blue back
When this function is “On,” this projector will produce a blue image
instead of the video noise on the screen when the input
source is unplugged or turned off.
Display
This function decides whether to display the On-Screen Displays.
On1
shows all the On-Screen Displays.
0n2
shows the On-Screen Displays except the Preparation
Display (Our Logo).
Off
sets the On-Screen Displays disappeared except;
•
•
•
•ON SCREEN MENU
•Power off?” message
•P-TIMER
Power management
This function turns the Projection Lamp off when the projector detects signal interruption and the projector is
not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is
shipped with this function ON.)
Power Management function operates to turn the Projection Lamp off
when the input signal is interrupted and the projector is not operated
over 5 minutes. This function operates as follows;
1. When the signal is interrupted, “No signal” and the counting
down (5 minutes) display appears.
2. When the Projection Lamp turned off, the READY indicator
turns off. The Cooling Fans operate for 90 seconds after the
Projection Lamp is turned off. (During this “Cooling Down”
period, the Lamp cannot be turned on.)
3. When the Lamp has cooled down, the READY indicator flashes
and the Lamp can be turned on again (Power Management
mode).
In this Power Management mode, the Projection Lamp is
automatically turned on when the input signal connected or the
projector is operated with any button on the Top Control or the
Remote Control.
On start
When this function is “On,” the projector is automatically turned on
just by switching the MAIN ON / OFF SWITCH on.
Note ; Be sure to turn the projector off properly (refer to the section
“TURNING OFF THE PROJECTOR” on page 20.). If the projector is
turned off in the wrong steps, the On Start function does not operate properly.
36
LC-XC1
Ceiling
When this function is “On,” the top / bottom and the left / right reversed
picture is provided to project the image from a ceiling mounted projector.
Rear
When this function is “On,” the left / right reversed picture is provided
to project the image to a rear projection screen.
Split wipe
Turn this function “On” in the SETTING MENU. The picture will change into
next one by sliding black image side ways like drawing the black curtains
when the input source is turned into another one.
Remote control
This projector has two different remote transmit codes; the factoryset normal code (Mode 1) and the secondary code (Mode 2). This
switching function prevents the remote control operation mixture
(jam) when operating several projectors or video equipment
together. When operating the projector in “Mode 2,” both projector and Remote Control must be switched to
“Mode 2.”
To change the code of the projector
Set the Remote control in SETTING MENU to “Mode 2.”
To change the code of the Remote Control
Press both the MENU and the NORMAL buttons on the Remote
Control together for over 10 seconds.
After changing the code, make sure the Remote Control operates
properly.
To return to the normal code (Mode 1), operate both projector and
Remote Control in the ways above again.
NOTE :
When the ALL-OFF switch on the Remote Control Unit is turned to “ALL-OFF,” the remote
transmit code automatically
returns to the normal code (Mode 1).
Lamp age
The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset
the lamp replacement monitor timer by using this function. (Refer to page 40.)
The language used in the ON-SCREEN MENU is selectable from among English, German, French, Italian,
Spanish and Japanese.
1
2
Press the MENU button and the ON-SCREEN MENU will
appear. Press POINT LEFT/RIGHT buttons to select
LANGUAGE and press the SELECT button. Another
dialog box LANGUAGE MENU will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the language that you want to
set, and then press the SELECT button.
37
LC-XC1
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless
mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the
wireless mouse operation.
The wireless mouse is available only when PC mouse pointer is displayed on the screen. When the menu or
the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse
cannot be used.
INSTALLATION
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the
mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your
computer. And make sure that the mouse port of the computer connected to Control Port is activated.
1
Connect the mouse port of your computer to the Control Port of
the projector with the Control Cable. (Refer to page 11 to 14 for
connection.)
2 Turn the projector on first, and then turn on your computer.
When the computer is switched on first, the Wireless Mouse may
Note: When the computer has no
mouse port, connect the
Serial Port of the computer to
Control Port of the projector
with the Control Cable for
Serial Port.
not work properly.
OPERATING WIRELESS MOUSE
When controlling the pointer of the computer, operate the
Wireless Mouse with POINT button, SELECT button, and
RIGHT CLICK button on the Wireless Remote Control Unit.
POINT button
Used to move the pointer. The pointer is moved corresponding
with the direction you are pressing.
SELECT (LEFT CLICK) button
This button has the same function as the left button in a PC
mouse.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse. Pressing this button does not affect any
operation when in Menu mode.
38
LC-XC1
TEMPERATURE WARNING INDICATOR
WARNING TEMP. Indicator flashes red when the internal temperature of the projector exceeds the normal
temperature. The Indicator stops flashing when the temperature of the projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check the items listed below.
1
2
3
The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the
ventilation slots are not obstructed.
Air filters may be clogged with dust particles. Clean the air filters by following the section AIR FILTER
CARE AND CLEANING below.
If WARNING TEMP. Indicator remains on after performing the above checks, the Cooling Fans or the Internal
Circuits may be malfunctioning. Contact service a personnel from an authorized dealer or service station.
AIR FILTER CARE AND CLEANING
The Removable Air Filter prevents dust from accumulating on
the surface of the Projection Lens and the
Projection Mirror. Should the Air Filter become clogged with dust
particles, it will reduce the Cooling Fans’
effectiveness and may result in internal heat build up and adversely
affect the life of the projector.
Clean the Air Filter following the steps below:
1
2
3
4
Turn the power off, and disconnect the AC power cord from the
AC outlet.
Turn the projector upside down and remove the Air Filter Cover
by pressing four latches sideways and pulling up. Remove three
Air Filters by pulling up the latches.
Clean the Air Filters with brush or wash out the dust and
particles. Be sure to dry them out.
Replace the Air Filters and Air Filter Cover properly. Make
sure that they are fully set.
CAUTION
Do not operate the projector with the Air Filter removed. Dust
may accumulate on the LCD Panel and the Mirror degrading
picture quality. Do not put small parts into the Air Intake Vents.
It may result in malfunction of the proiector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating the
projector. Usage in these environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, lens, or optical
elements inside it. This condition may degrade the quality of the projected image. When the above symptoms are
noticed, contact your authorized dealer or service station for proper cleaning.
39
LC-XC1
LAMP REPLACEMENT
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights
yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is
required.
CAUTION
• For continued safety, replace with a lamp assembly of the same type.
•AIlow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector
can become very hot.
• Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
1 Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 45 minutes.
2 Remove the screw with a screwdriver and remove the Lamp
Cover.
3
4
5
6
Remove the two screws with a screwdriver and pull out the
Lamp Assembly by grasping the handle.
Replace the Lamp Assembly with a new one and tighten the
two screws. Make sure that the Lamp Assembly is set
properly. Replace the Lamp Cover and tighten the screw.
Connect the AC Power Cord to the projector and turn the
projector on.
Reset the Lamp Replacement Monitor Timer (refer to the
section
“Lamp Replacement Monitor Timer” below).
NOTE: Do not reset the LAMP REPLACEMENT MONITOR
TIMER when the lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following
information to the dealer.
• Model No. of your projector :
LC-XC1
• Replacement Lamp Type No.: POA-LMP28
(Service Parts No. 610 285 4824)
LAMP REPLACEMENT MONITOR TIMER
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the
Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
1
2
3
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
LEFT/RIGHT buttons to select SETTING and press the SELECT button (refer to the page 36, 37). Another dialog
box SETTING MENU will appear.
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age,” and then press
the SELECT button. The message “Lamp replace monitor Reset?” is displayed.
Select to reset the Timer.
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.
40
LC-XC1
CLEANING ThE PROJECTION LENS
Follow these steps to clean the projection lens:
1
2
3
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive
amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
Lightly wipe the cleaning cloth over the lens.
When the projector is not in use, replace the lens cover.
41
LC-XC1
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment as described in the section
“CONNECTING THE PROJECTOR” on pages ii 14.
2. Check cable connection. Verify that all computer, video and power cords are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce an image, re-start the computer.
5. If the image sill does not appear, unplug the projector from the computer and check the computer
monitor’s display. The problem may be with your graphics controller rather than with the projector. (When
you reconnect the projector, remember to turn the computer and monitor off before you power up the
projector. Power the equipment back on in order of: Projector and computer.)
6. If the problem still exists, check the following chart.
Problem
Try these Solutions
No Power
• Plug the projector into the AC outlet.
• Be sure READY Indicator light is On.
• Wait 90 seconds after the projector is turned OFF before turning the projector
back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the
projector works as follows:
1. The LAMP indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY indicator will light green again and the
projector may be turned on by pressing the power ON-OFF button.
Image is out of focus
• Check WARNING TEMP. indicator. If the indicator flashes red, the projector
cannot be turned on.
(See “TURNING ON/OFF THE PROJECTOR” section on page 20.)
• Check the Projection Lamp. (Refer to page 40.)
• Adjust the focus
• Make sure the projection screen is at least 4.6’ (1 .4m) from the projector.
• Check the projection lens to see if it needs cleaning.
NOTE :
Moving the projector from a cool temperature location to a warm
temperature location may result in moisture condensation on the lens. In such
an event, leave the projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed
• Check Ceiling / Rear feature. (See “SETTING” section on page 36.)
Picture is
Top/Bottom
reversed.
Some displays are not
seen during the
Operation.
No image
• Check Ceiling feature. (See “SETTING” section on page 36.)
No sound.
• Check Display feature. (See “SETTING” section on page 36.)
• Check the connection between the computer or video equipment and the
projector.
• When turning the projector on, it takes about 30 seconds to display the image.
• Check the system that you select is corresponding with the computer or the
video equipment.
• Make sure the temperature is not out of the Operating Temperature (5°C
35°C).
• Check audio cable connection from audio input source.
• Adjust the audio source.
• Press VOLUME (+) button.
• Press MUTE button.
42
Problem:
Remote Control Unit does not
work
Wireless Mouse function does
not work.
WARNING:
High voltages are used to
cabinet.
Try these Solution
LC-XC1
Check the batteries.
Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
Make sure nothing is between the Remote Receiver and the Remote
Control Unit.
Make sure you are not too far from the projector when using the
Remote Control Unit. Maximum operating range is 16.4’ (5m).
Make sure the code of the Remote Control is set to conform to the
projector. (See “SETTING” section on page 36, 37.)
• Check the cable connection between the projector and the computer.
• Check the mouse setting on your computer.
•
Turn the projector on before you turn on the computer.
operate this projector. Do not attempt to open the
If the problem still persists after following all operating instructions, contact the sales dealer where you
purchased the projector or the service center. Give the model number and explain the difficulty. We
will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
43
LC-XC1
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Panel Resolution
Number of Pixels
Color System
High Definition TV
Signal
Scanning Frequency
Projection Image size
(Diagonal)
Horizontal Resolution
Projection Lens
Throw Distance
Projection Lamp
AV Input Jacks
AV Audio Input Jacks
Computer Input Jacks
Computer Audio Input
Jacks
Control Port Jacks
Monitor Output Jacks
Audio Output Jacks
Internal Audio Amp
Built-in Speakers
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
Storage Temperature
Remote Control
Transmitter
Multi-media Projector
12.44” x 6.46” x 18.9” (31 6mm x 164mm x 480mm)
20.3 lbs (9.2 kg)
1 3” TFT Active Matrix type, 3 panels
1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, i035i, 1080i-50 and iO8Oi-60
H-sync. 15 100 KHz, V-sync. 50 100 Hz
Adjustable_from_31” to 400”
800 TV lines
F 1.8 2.1 lens with f 48.4 mm 62.8 mm with motor zoom, focus and shift
4.6’ 47.2’ (1.4 m 14.4 m)
250 W
RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
RCA Type x 2
(VGA) HDB 15 Terminal x 1, DVI 24 pin x 1, and BNC jack x 5
Mini Jack (stereo) x 2
Mini DIN 8 pin x 2
BNC jack x 5 (Computer) and RCA Type x 1 (Video)
RCA Type x 2
2.0 W RMS (stereo)
2 speakers, 1.57” x 2,76” (40mm x 70mm)
o
o
0 to 9.0
AC 100 120 V (4.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 240 V (2.2 A Max. Ampere), 50 / 60 Hz (Continental Europe)
o
o
o
o
41 F 95 (5 C 35 C)
o
o
o
o
14 F 140 (-10 C C)
Power Source :
AA, UM3 or R06 Type x 2
Operating Range :
16.4’ (5m) / ±30~
Dimension
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
-
-.
Net Weight
Laser Pointer
Accessories
: 0.36 lbs (165 g) (including batteries)
:
Class II Laser (Max. Output: 1mW / Wave length : 650±2Onm)
Owner’s Manual
AC Power Cord
Wired/Wireless Remote Control Transmitter and Batteries
VGA Cable
MAC Adapter
Control Cable for PS/2 port
Control Cable for Serial port
Control Cable for ADB port
Remote Control Cable
Dust Cover
Lens Cover
• The specifications are subject to change without notice.
44
LC-XC1
CONFIGURATIONS OF THE TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG)
Terminal : HDB1 5-PIN
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting
the Macintosh computer, the MAC Adapter (supplied) is required.
CONTROL PORT CONNECTOR
Terminal:Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (supplied).
COMPUTER INPUT-i TERMINAL (DIGITAL)
Terminal : DVI 24-pin
Connect the display output terminal of the computer to this terminal with the DVI
cable (not supplied).
CONTROL PORT CONNECTOR
Terminal: Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (supplied).
MAC ADAPTER
Set the switches as shown in the table below depending on the RESOLUTION MODE that you want to use
before you turn-on the prolector and computer.
45
EIKI INTERNATIONAL, INC.
26794 Vista Terrace Drive, Lake Forest,
CA. 92630-8113, U.S.A.
TEL (949) 457-0200 FAX (949) 457-7878
ElKI CANADA
865 Heritage Drive P.O. Box 156
Midland Ontario L4R 4K8 Canada
TEL (705) 527-4084 FAX (705) 527-4087
EIKI DEUTSCHLAND GMBH
AM Frauwald 12 65510 Idstein
Germany
TEL (6126) 9371-0 FAX (6126) 9371-11
EIKI CZECH SPOL. S.R.O.
Umelccka 15, 170 00 Praha 7 Holesovice
Czech Republic
TEL (2) 20571413 FAX (2) 20571411
ElK! INDUSTRIAL CO., LTD
4-12 Banzai-cho, Kita-Ku
Osaka, Japan
TEL (6) 6311-9479 FAX (6) 6311-8486
Printed in Japan
Part No. 610 287 0503 (1 AA6P1 P2356-- MM6B)
© 2000 Eiki International, Inc.
46
Download PDF

advertising