Electrolux 2020 D Ventilation Hood User Manual

2020 D
Cooker Hood
Operating and Installation
Instructions
For the User
For the Installer
Important Safety Information
Installation Instructions
Technical Information
Your Appliance
Electrical Connections
Electrical Requirements
Electrical Connection
Operating Instructions
Cooker Hood Controls
To Operate
Recirculation
Extraction
Installing the Cooker Hood
Service and Spare Parts
Installation Requirements
Unpacking
Clearance Height
Selecting the Type of Installation
Fixing the Chimney to the Canopy
Fitting the Hood to the Wall
Drilling the Shelves
Bottom Shelf
Top Shelf
Installation in Recirculation Mode
Installation with Air Outlet Turned to the Wall
Installation with Air Outlet Turned Left or Right
Final Fixing and Adjustment of Hood
Ducting
Recirculation
Guarantee Conditions
Electrical Connection and Working Test
Maintenance and Cleaning
External Cleaning
Metal Grease Filter
To Remove the Grease Filter Cassette
Charcoal Filter
To Remove/Replace the Charcoal Filter
Worktop Lighting
Replacing the Light Bulb
Something Not Working
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instruction book
Safety instructions
Step by step instructions
2
IMPORTANT SAFETY INFORMATION
These warnings are provided in the interests of your safety. Ensure that you understand them all before
installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of
the meanings of these warnings contact the Customer Care Department.
Installation
•
•
•
•
•
•
•
•
•
•
•
Child Safety
Any installation work must be undertaken by a
qualified electrician or competent person.
This hood must be installed in accordance with
the installation instructions and all measurements
adhered to.
If the cooker hood is installed for use above a gas
appliance then the provision for ventilation must
be in accordance with the Gas Safety Code of
Practice BS.6172, BS.5440 and BS.6891 (natural
gas) and BS.5482 (LP gas) 1994, the Gas Safety
(Installation & Use) Regulations, the Building
Regulations issued by the Dept. of the
Environment, the Building Standards (Scotland)
(Consolidated) Regulations issued by the Scottish
Development Department.
The fan motor of the cooker hood incorporates a
cut-out device, which will operate if the cooker
hood is installed below the minimum height
recommended in the Technical Information
section, or if the motor becomes overheated. If
the cut-out device is activated, switch off the motor
and allow the hood to cool. The cut-out device
will reset itself when the fan motor has cooled.
It is dangerous to alter the specifications or modify
this product in any way.
When installed between adjoining wall cabinets,
the cabinets must not overhang the hob.
If the room where the hood is to be used contains
a fuel burning appliance such as a central heating
boiler then its flue must be of the room sealed or
balanced flue type.
If other types of flue or appliances are fitted ensure
that there is an adequate supply of air to the room.
When the hood is used in conjunction with
appliances supplied with energy other than
electricity, the negative pressure in the room must
not exceed 0.04mbar to prevent fumes being
drawn back into the room by the hood.
The ducting system for this appliance must not be
connected to any existing ventilation system which
is being used for any other purpose.
Do not install above a cooker with a high level
grill.
•
The appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the appliance.
•
•
This appliance is for domestic use only.
Never leave frying pans unattended during use
as over-heated fats and oils might catch fire.
Never do flambé cooking under this cooker hood.
Do not leave naked flames under this hood.
During Use
•
•
Maintenance and Service
•
•
3
This appliance can be a fire hazard if the grease
and charcoal filters are not cleaned or replaced
as recommended.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local Service
Force Centre. Always insist on genuine spare
parts.
YOUR APPLIANCE
OPERATING INSTRUCTIONS
This cooker hood is designed to extract unpleasant
odours from the kitchen, it will not extract steam.
To obtain the best performance it is advisable to switch
on the hood a few minutes before you start cooking and
leave it running for approximately 15 minutes after
finishing.
Cooker Hood Controls
V1.
V2.
V3.
L.
Push to engage the low speed, for use with one
burner or simmering.
Push to engage the medium speed, for normal
cooking up to four pans.
Push to engage the high speed, for use when
frying or cooking foods with strong odours.
Push to switch on the worktop illumination lamps.
4
OPERATING INSTRUCTIONS
This cooker hood can be used to recirculate or extract
contaminated air.
Recirculation
The cooker hood is supplied specified for use in the
recirculation mode with the charcoal filter fitted.
The contaminated air is cleaned by passing through the
filters and than back into the kitchen.
S07_29
The activated charcoal filter absorbs odours arising from
cooking. In use it will slowly become saturated in grease
and less effective. The filter normally requires changing
after at least every three months or more frequently if
the hood is used for more than three hours per day.
Extraction
The contamined air enters the cooker hood passing
through the grease filter and out through the ducting into
the atmosphere.
When used in the extraction mode the charcoal filter is
not required and must be removed.
S07_03
Never do flambé cooking under this
cooker hood.
Take extra care when frying and never
leave frying pans unattended during
use, as over-heated fats and oils can
catch fire.
R
Do not leave naked flames under the
cooker hood.
Ensure the hood is switched on
before using the hob.
Ensure heating areas on your hob are
covered with pots and pans when using
the hob and cooker hood
simultaneously.
W
S07_30
Ensure not to damage the charcoal filter
when cleaning or replacing as the activated
charcoal inside is saturated with grease,
which will stain if it comes into contact
with clothing or furnishings.
5
R
W
MAINTENANCE AND CLEANING
Before carrying out any maintenance or
cleaning isolate the cooker hood from the
mains supply.
The cooker hood must be kept clean, a build
up of grease or fat can be a fire hazard.
External Cleaning
S07_06
The metal casing, grille and chimney should be cleaned
at least once a month to keep it looking like new. Wipe
over the hood with a soft cloth wrung out in mild
soapy water and then dry thoroughly.
Never use scouring pads or abrasive cleaners as they
may scratch or damage the surfaces.
Always wear protective gloves when cleaning
the hood.
Never use scouring pads or abrasive cleaners.
Never use excessive amounts of water when
cleaning particularly around the control panel.
Metal Grease Filter
The metal grease filter should be cleaned at least every
month. The filter may be washed by hand using mild
soapy water, or can be machine washed in a
dishwasher.
To Remove the Grease Filter
Remove the metal grease filter cassette by pushing
inwardly on the two steel handles; replace, making sure
the handle has sprung back into position and is
completely visible.
Charcoal Filter
The charcoal filter cannot be cleaned, it should be
replaced approximately every three months or more often
if the hood is used for more than three hours per day.
6
MAINTENANCE AND CLEANING
To Remove the Charcoal Filter
Push inwardly on the two retaining clips to disengage
the security fixing and remove.
S07_27
This appliance can be a fire hazard if the
grease and charcoal filters are not
cleaned and replaced as recommended.
S07_31
Worktop Lighting
The lamps should be replaced with a 220-240V 20W
halogen spot lamp.
To Remove the Lamps
Unscrew the two screws to release the metal surround.
Remove a lamp from the holder by pulling the lamp
downwards.
S07_28
When fitting the new lamp ensure the two pins are
correctly inserted into the slots in the lamp holder.
Charcoal filters, grease filters and lamps can be
obtained from your local Service Force Centre.
7
SOMETHING NOT WORKING
If, having followed these instructions carefully, your cooker hood fails to work properly please carry out
the following checks.
Solution
Symptom
The cooker hood will not start
• Check the hood is connected to the electricity supply.
• Check that the fan speed control is set to 1, 2 or 3.
The cooker hood is not working effectively
• The fan speed is set high enough for the task.
• The grease filter is clean.
• The kitchen is adequately vented to allow the entry
of fresh air.
• If set up for recirculation, check that the charcoal
filter is still effective.
• If set up for extraction, check that the ducting and
outlets are not blocked.
The cooker hood has switched off during
operation
• The safety cut-out device has been tripped.
• Tum off the hob and then wait for the device to reset.
In-guarantee customers should ensure
that the above checks have been made as
the engineer will make a charge if the fault
is not a mechanical or electrical
breakdown.
If after all these checks, the problem persists,
contact your local Service Force Centre,
quoting the model and serial number.
Please note that it will be necessary to
provide proof of purchase for any
in-guarantee service calls.
SERVICE AND SPARE PARTS
If you require an engineer or wish to purchase spare
parts contact your local Service Force Centre by
telephoning:
For general assistance with your appliance or for
information on other AEG products please contact our
Customer Care Department.
Customer Care Department
AEG
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 929929
Your telephone call will be routed to the Service Force
Centre covering your postcode area.
Telephone: 08705 350350 *
* calls to this number may be recorded for training
purposes
8
GUARANTEE CONDITIONS
Standard Guarantee Conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option,
repair or replace the same FREE OF ANY CHARGE for labour, materials and carriage on condition that:
•
The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
•
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
operating and maintenance instructions.
•
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
•
All service work under this guarantee must be undertaken by an AEG Service Force Centre.
•
Any appliances or defective parts replaced shall become the property of this company.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours
in which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
•
Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United
Kingdom.
•
Appliances found to be in use within a commercial environment, plus those which are the subject of rental
agreements.
•
Products of AEG manufacture which were not marketed by AEG. This guarantee is in addition to your statutory
and legal rights.
EUROPEAN GUARANTEE
If you move to another country within Europe then your guarantee moves with you to your new home subject to the
following qualifications:
•
The guarantee starts from the date you first purchased your product.
•
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
•
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
•
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of
your new home. They will ensure that the local Service organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nurnberg
Pordenone
Stockholm
Slough
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)01678 47053
+46 (0)8 738 79 50
+44 (0)1753 219899
9
INSTALLATION INSTRUCTIONS
It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical Information
DIMENSIONS
HEIGHT (CANOPY):
HEIGHT (CHIMNEY):
WIDTH (CANOPY):
WIDTH (CHIMNEY):
GROSS:
NET:
ELECTRICAL SUPPLY:
POWER CONSUMPTION:
FAN MOTOR:
LAMP:
(2x20W) HALOGEN Ø 35 mm GUA
SUITABLE FOR INSTALLATION
ABOVE:
73 mm
450-850 mm
898 mm
Ø200-Ø270 mm
24.00 kg
19,40 kg
220-240 V (50 Hz)
215 W
175 W
40 W
ELECTRIC HOB:
GAS HOB:
SLOT-IN GAS COOKER
SLOT-IN ELECTRIC COOKER
7 KW
10 KW
13.5 KW
12.4 KW
Note: CE Marking certifies that this appliance complies with the requirements
laid down in EEC directive 89:336. (Electromagnetic compatibility) and
subsequent modifications and Low Voltage directive 72/23/E.
ELECTRICAL CONNECTIONS
This appliance must be earthed
Electrical Requirements
This appliance is fitted with a 3 core mains
cable and must be permanently connected to
the electricity supply via a double-pole switch
having 3mm minimum contact gap on each
pole. A Switched Fuse Connection Unit to
BS1363 Part 4, fitted with a 3 Amp fuse, is a
recommended mains supply connection
accessory to ensure compliance with the Safety
Requirements applicable to fixed wiring
instructions.
Any permanent electrical installation must
comply with the latest I.E.E. Regulations and
local Electricity Board regulations. For your own
safety this should be undertaken by a qualified
electrician e.g. your local Electricity Board, or a
contractor who is on the roll of the National
Inspection Council for Electrical Installation
Contracting (NICEIC).
Electrical Connection
Before connecting to the mains supply ensure
that the mains voltage corresponds to the
voltage on the rating plate inside the cooker
hood.
This appliance conforms to BS 800: 1988 and
EEC Directive No. 78 308 regarding
suppression of radio and television
interference.
10
INSTALLING THE COOKER HOOD
Please ensure that when the appliance is installed it
is easily accessible to an engineer in the event of a
breakdown.
All installations must comply with the
local authorities requirements for the
discharge of exhaust air.
Incorrect installation may affect the
safety of this cooker hood.
Installation Requirements
Before installation check the wall to
which the cooker hood is to be fitted for
electric cables, water pipes or gas.
The cooker hood is designed to be fixed to any rigid
vertical surface over a cooking area, and can be used in
the extraction (ducted to the outside) or recirculation
(internal recycling) mode.
The Installation work must be undertaken by a qualified
and competent person. The manufacturer disclaims any
responsibility to damages due to incorrect installation of
the cooker hood or if the cooker hood is not installed in
compliance with relevant regulations controlling this type
of installation.
Unpacking
Before unpacking the cooker hood position the carton
with the arrows pointing upwards as illustrated on the
carton.
S
F
The canopy is supplied with the following
components for installation:
G
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
Canopy including controls and worktop illumination (C).
Telescopic chimney stack complete with fan motor (A). R
Flange 120mm (F).
Collar 120-125mm
Venting grille (G).
W
Spigot (R).
Ducting conversion bend (W)
Support Rod (B)
B
11
INSTALLING THE COOKER HOOD
Clearance Heights
The cooker hood is designed to be fitted over a cooking
appliance at the clearance heights stated, provided the
maximum output of the appliance beneath does not
exceed the maximums quoted in the Technical
Specifications.
If the output of the appliance below the cooker hood
exceeds the maximum outputs quoted, please refer to
the cooker manufacturer’s installation instructions.
Hob
A minimum clearance height of 650mm (25 1/2 ins) is
required when installed above a built-in electric hob, or
700mm (27 1/2 ins) when installed above a built-in gas
hob.
A: Built-in Electric Hob:
B: Built-in Gas hob:
C: Slot-in Electric Cooker:
D: Slot-in Gas Cooker:
A minimum clearance height of 685mm (27 ins) is
required when installed above a slot-in electric oven, or
787mm (30 1/2 ins) when installed above a slot-in gas
oven.
G
S07_03
When installed between adjoining wall cabinets, the wall
cabinets must not overhang the hob and the distance
beetween the underside of the cabinet and the worktop
must be 450mm. If the height of the wall cabinet is less
than 450mm a gap of 50mm must be maintained
either side of the hob.
650mm minimum clearance
700mm minimum clearance
685mm minimum clearance
787mm minimum clearance
This cooker hood must not be installed
above a cooking appliance with a high
level grill.
3
2a
R
Selecting the type of installation:
W
The extraction unit at the top of the chimney can be
installed in one of three ways.
Air outlet turned upwards recirculation only (fig.
2a).
2.
Air outlet turned towards the wall -extraction only
(fig. 3).
3.
Air outlet turned left or right -extraction only (fig.
4a and 4b).
4b
W
S07_30
1.
12
R
4a
INSTALLING INSTRUCTIONS
Fixing the Chimney to the Canopy
1.
Remove the metal grease filter cassette by
pushing inwardly on the two steel handles.
2.
To remove the charcoal filter push inwardly on
the two retaining clips to disengage the security
fixing and remove.
3.
4.
5.
A
Align the fixing points on the chimney with the
corresponding fixing points on the canopy. Ensure
the guide in the two chimney sections is
positioned at the back to face the wall.
G1
C
Fixing the chimney stack :
Insert gasket G1 (found in the accessory bag) on
the base of chimney stack A, so that it adheres
perfectly to the shape of chimney stack A. Then
fix chimney stack A to the hood unit C using four
of the screws provided E.
E
E
Connect the supply cable from the canopy
(marked with adhesive tape), to the cable from
the fan motor by pushing together the two (male
and female) connectors.
A08_TL
The metal grease filter and charcoal filter should not
be refitted until after the hood has been fixed to the
wall.
If the hood is to be fitted in conjunction with wooden
shelves or cornice see the separate installation
instructions before fixing the hood in position.
Whichever type of installation is to be carried out, if the
hood is to be fitted in conjunction with wooden shelves
these will require drilling before the hood can be
installed.
S07_08
Fixing the hood to the wall:
1.
Use the cardboard template provided to mark the
hole positions on the shelf.
2.
Using hole ‘B’ as a reference point, drill the shelf
along the centre axis, for the chimney to pass
through.
S07_09
Drilling the shelves:
Bottom Shelf
13
E
E
INSTALLING INSTRUCTIONS
3.
Slide the chimney through the hole in the shelf
before fixing it to the canopy.
Top Shelf
The top shelf only requires drilling if the hood is to be
installed with the air outlet turned upwards.
1.
Use the cardboard template provided to mark the
hole position on the shelf.
2.
Using the hole ‘B’ as a reference point, drill the
shelf along the centre axis for the chimney to pass
through.
Installation in the recirculation mode:
The cooker hood is specified for installation in the
recirculation mode with the charcoal filter fitted.
4.
2
X
1
20
1
48
Using the cardboard template mark the hole
positions (to be used for fixing the chimney)
30mm either side of the vertical line. The holes
must be drilled at a distance of (X) from the
horizontal line running through the centre of the
canopy fixing holes (1), which is calculated by
measuring the lenght of the chimney required for
the installation plus 15mm equal (Z).
650
3.
ø1
Using the cardboard template provided mark the
hole position (1) on the wall 100mm either side
of the vertical line ensuring they are level and
that the distance between the lowest point of the
hood and the cooking appliance beneath meet
the clearance requirements quoted in the
paragraph titled ‘Clearance Heights’.
7
2.
Z
Draw a vertical line on the wall from the centre of
the cooking appliance, using a spirit level and
marking pen. This is to ensure the correct vertical
alignment of the appliance.
50
20
ø1
1.
Using a 8mm masonry bit, drill the holes for the
canopy and the fan assembly and insert the rawl
plugs provided ready for the fixing screws.
S07_05
14
100 100
ø8
INSTALLING INSTRUCTIONS
Fix the round eyelet screws provided tightly into
the holes (1).
6.
Fix bracket (S) to the fan assembly.
7.
The hood is supplied in the recirculation mode,
with the recirculation grille (G) fitted over the outlet
in the top of the fan assembly ready for use.
8.
Insert the 4.2x44.4mm screws to be used for
fixing the fan assembly into the rawl plugs and
tighten about two thirds. Lower the fan assembly
and chimney onto the fixing bracket (S). Ensuring
the screws locate into the fixing bracket, than
tighten the screws fully.
S
S07_11
5.
Installation with the air outlet turned
towards the wall:
4.
20
ø1
7
X
Z
1
20
1
100 100
Using the cardboard template mark the hole
positions (to be used for fixing the chimney)
30mm either side of the vertical line. The holes
must be drilled at a distance of (X) from the
horizontal line running through the centre of the
canopy fixing holes (1), which is calculated by
measuring the lenght of the chimney required for
the installation plus 15mm to equal (Z) as
illustrated opposite.
S07_05
Using a 8mm masonry bit, drill the fixing holes
for the canopy and the fan assembly and insert
the rawl plugs provided ready for the fixing
screws.
G
S07_23
3.
2
48
Using the cardboard template provided mark the
hole positions (1) on the wall 100mm either side
of the vertical line ensuring they are level and
that the distance between the lowest point of the
hood and the cooking appliance beneath meet
the clearance requirements quoted in the
paragraph titled ‘Clearance Heights’.
650
2.
50
Draw a vertical line on the wall from the centre of
the cooking appliance, using a spirit level and
marking pen. This is to ensure the correct vertical
alignment of the appliance.
ø1
1.
15
ø8
Mark the position on the wall and drill the hole
for the ducting. To calculate the centre of the hole
on the wall for the ducting, draw a horizontal line
(D) through the vertical line 80mm above line (X)
The round ducting to be used must be Ø125mm.
6.
Fix the round eyelet screws provided tightly into
holes (1) and hook on the canopy (C) ensuring
the hooks are located into the eyelets before
releasing the canopy.
7.
Unscrew the self tapping screws from the back
of the fan assembly and remove the plastic
surround.
8.
Fit the ducting flange (F) onto the fan assembly
utilising the same fixing holes and self tapping
screws.
9.
Insert the 4.2x44.4mm screws provided, for fixing
the fan assembly and chimney into the wall and
tighten about two thirds. Lower the fan assembly
and chimney onto the fixing bracket (S), than fully
tighten the screws.
S07_16
5.
S07_14
INSTALLING INSTRUCTIONS
Installation with the air outlet turned
left or right:
1.
2
Draw a vertical line on the wall from the centre of
the cooking appliance, using a spirit level and
marking pen. This is to ensure the correct vertical
alignment of the appliance.
48
Using the cardboard template provided mark the
hole positions (1) on the wall 100mm either side
of the vertical line ensuring they are level and
that the distance between the lowest point of the
hood and the cooking appliance beneath meet
the clearance requirements quoted in the
paragraph titled ‘Clearance Heights’.
3.
Using the cardboard template mark the hole
positions (to be used for fixing the fan assembly)
107.5mm on the left or right of the vertical line.
The holes must be drilled at a distance of (X) from
the horizontal line running through the centre of
the canopy fixing holes (1), which is calculated
by measuring the lenght of the chimney required
for the installation plus 15mm to equal (Z).
S07_20
35
2.
2
16
INSTALLING INSTRUCTIONS
The hood is supplied with the air outlet facing
the rear. To rotate the extractor to face left or right
proceed as follows:
(A)
Loosen the screws (V1), turn the extractor 60° to
the left or right as required, then tighten the
screws.
(B)
To fix the bracket (S), select the left or right hand
screw holes and using the screw (V2) secure the
bracket.
6.
Unscrew the four self tapping screws and remove
the plastic surround.
7.
Fit the ducting spigot (R) using the four self
tapping screws and replace the plastic cover.
8.
Fix the round eyelet screws provided tightly into
holes (1) and hook on the canopy (C) ensuring
the hooks are located into the eyelets before
releasing the canopy.
9.
Unscrew the self tapping screws from the back
of the fan assembly and remove the plastic
surround.
10.
Fit the ducting flange (F) onto the fan assembly
utilising the same fixing holes and self tapping
screws.
11.
Insert the 4.2x44.4mm screws provided for fixing
the fan assembly and chimney into the wall and
tighten about two thirds. Lower the fan assembly
and chimney onto the fixing bracket (S), then fully
tighten the screws.
S
S07_18
5.
S
S07_22
Using a 8mm masonry bit, drill the holes for the
canopy and fan assembly and insert the rawl
plugs ready for the fixing screws.
R
S07_19
4.
17
INSTALLING INSTRUCTIONS
Final fixing and adjustment of the
hood:
Two adjustable connectors are provided at the rear of
the hood.
(b)
(c)
(d)
(e)
Turn the screws (V1), until the screws (V2) align
with the screw holes (F2).
Adjust the vertical and horizontal alignment using
screws (V2).
Turn the screw (V1) to secure the hood to the
wall.
Insert the plastic grommets provided into the
screw holes (F2).
Tighten the screws fixing the canopy (C) to the
chimney (A).
F
V1
F
S07_21
(a)
Ducting and recirculation fitting:
1.
When ducting to the outside the charcoal filter is
not required and must be removed and destroyed.
2.
When ducting from the rear outlet using 125mm
round ducting it will be necessary to fit the 120125mm ducting collar onto the spigot (F) before
connecting the ducting, to ensure an air tight fit.
This appliance must not be connected to ducting
with a smaller diameter than 120mm.
3.
When ducted from the left or right hand side, it
will be necessary to fit the 60x204mm adapter
(W) for use with flat channel ducting to the spigot
(R).
S07_22
Ducting
Recirculation
The hood is supplied in the recirculation mode,
with the charcoal filter and the recirculation grille
(G) fitted (over the outlet in the top of the fan
assembly) ready for use.
2.
The charcoal filter will have to be removed during
installation to allow for electrical connection.
R
S07_19
1.
18
V2
INSTALLING INSTRUCTIONS
Electrical connection and working
test:
1.
Remove the metal cover by unscrewing the four
self tapping screws.
2.
Connect the ‘Push-Fit’ connectors coming from
the fan assembly to the canopy.
3.
Position the terminals as illustrated under the
cover and replace the cover with the four self
tapping screws.
4.
Once the electrical connection has been
completed, check that the worktop lighting, fan
motor and the speed selection is working properly.
5.
Replace the charcoal filter (if the hood is to be
used in the recirculation mode) and the metal
grease filter cassette.
S07_24
S07_34
19
4329477 01 - 001013